Craftsman CMCM300B Manuel utilisateur

Marque: Craftsman

Modèle: CMCM300B

Catégorie: Outils électroportatifs

Taper: Manuel utilisateur

final page size: 8.5 x 5.5 in

INSTRUCTION MANUAL GUIDE D’UTILISATION MANUAL DE INSTRUCCIONES

CMCM300

20V MAX* 3 Inch Cutoff Tool

Outil de coupe 20V MAX* 3 po

Herramienta de corte de 3 pulgadas 20V MAX*

IF YOU HAVE QUESTIONS OR COMMENTS, CONTACT US.

POUR TOUTE QUESTION OU TOUT COMMENTAIRE, NOUS CONTACTER.

SI TIENE DUDAS O COMENTARIOS, CONTÁCTENOS.

1-888-331-4569 WWW.CRAFTSMAN.COM

English (original instructions) 5

Français (traduction de la notice d’instructions originale) 17

Español (traducido de las instrucciones originales) 31

Fig. A

1 Battery pack

2 Battery pack release button

3 Main handle

4 Variable speed trigger

5 Forward/reverse/lock off button

6 Spindle lock button

7 Direction indicator

8 Dust port adapter

9 Shoe

10 Depth adjustment knob

11 Rotatable Guard

12 Hex wrench

13 LED worklight

14 Accessory attacment location

1 Paquete de batería

2 Botón de liberación de paquete

de batería

3 Manija principal

4 Gatillo de velocidad variable

5 Botón de bloqueo de apagado/

avance/reversa

6 Botón de bloqueo de husillo

7 Indicador de dirección

8 Adaptador de puerto de polvo

9 Zapata

10 Perilla de ajuste de profundidad

11 Protección giratoria

12 Llave hexagonal

13 Linterna LED

14 Ubicación de conexión de accesorio

1 Bloc-piles

2 Bouton de libération du bloc-piles

3 Poignée principale

4 Gâchette à vitesse variable

5 Bouton Avance/recul/verrouillage

6 Bouton de verrouillage de la tige

7 Indicateur de direction

8 Adaptateur de port antipoussière

9 Sabot

10 Bouton d’ajustement de la

profondeur

11 Protection rotative

12 Clé hexagonale

13 Lampe de travail à DEL

14 Emplacement des accessoires

Fig.B Fig.C

Fig.D Fig.E

Fig.F1

Fig.F2

19 12

75–100% charged

Chargé de 75 à 100 %

75–100% cargada

51–74% charged

Chargé de 51 à 74 %

51–74% cargada

< 50% charged

Chargé de < 50 %

< 50% cargada

Pack needs to be charged

Le bloc‑piles doit être rechargé

La batería tiene que cargarse

Indicators for all chargers except CMCB101

Voyants pour tous les chargeurs sauf CMCB101

Indicadores para todos los cargadores excepto CMCB101

Charging

Bloc‑piles en Cours

de Chargement

Unidad en Proceso de Carga

Fully Charged

Bloc‑piles Chargé

Unidad Cargada

Hot/Cold Pack Delay

Suspension de Charge Contre

le Chaud/Froid

Restraso por Unidad Caliente/Fría

Only CMCB101 Charger Indicators

Seulement les voyants de chargeur CMCB101

Indicadores únicamente para cargador CMCB101

Charging

Bloc‑piles en Cours

de Chargement

Unidad en Proceso de Carga

Fully Charged

Bloc‑piles Chargé

Unidad Cargada

Hot/Cold Pack Delay

Suspension de Charge Contre

le Chaud/Froid

Restraso por Unidad Caliente/Fría

Fig.H

Fig.I

Fig.J1 Fig.J2

Fig.G

Fig.M

Fig.N

Fig.L

Fig.O

Fig.K1 Fig.K2

14 28

ENGLISH

English (original instructions)

WARNING: Read all safety warnings and all

instructions. Failure to follow the warnings and

instructions may result in electric shock, fire and/or

seriousinjury.

WARNING: To reduce the risk of injury, read the

instructionmanual.

Definitions: Safety Alert Symbols and Words

This instruction manual uses the following safety alert

symbols and words to alert you to hazardous situations and

your risk of personal injury or propertydamage.

DANGER: Indicates an imminently hazardous

situation which, if not avoided, will result in death or

seriousinjury.

WARNING: Indicates a potentially hazardous situation

which, if not avoided, could result in death or

seriousinjury.

CAUTION: Indicates a potentially hazardous situation

which, if not avoided, may result in minor or

moderateinjury.

NOTICE: Indicates a practice not related to

personal injury which, if not avoided, may result in

propertydamage.

(Used without word) Indicates a safety

relatedmessage.

Intended Use

Your cut-off tool is designed for professional

cuttingapplications.

DO NOT use in the presence of flammable liquids orgases.

Your cut-off tool is a professional powertool.

DO NOT let children come into contact with the tool.

Supervision is required when inexperienced operators use

thistool.

GENERAL POWER TOOL SAFETY WARNINGS

WARNING: Read all safety warnings, instructions,

illustrations and specifications provided with

this power tool. Failure to follow all instructions

listed below may result in electric shock, fire and/or

seriousinjury.

SAVE ALL WARNINGS AND INSTRUCTIONS

FORFUTUREREFERENCE.

The term "power tool" in the warnings refers to your

mains‑operated (corded) power tool or battery‑operated

(cordless) powertool.

1) Work Area Safety

a ) Keep work area clean and well lit. Cluttered or dark

areas inviteaccidents.

b ) Do not operate power tools in explosive

atmospheres, such as in the presence of

flammable liquids, gases or dust. Power tools create

sparks which may ignite the dust orfumes.

c ) Keep children and bystanders away while

operating a power tool. Distractions can cause you

to losecontrol.

2) Electrical Safety

a ) Power tool plugs must match the outlet. Never

modify the plug in any way. Do not use any

adapter plugs with earthed (grounded) power

tools. Unmodified plugs and matching outlets will

reduce risk of electricshock.

b ) Avoid body contact with earthed or grounded

surfaces, such as pipes, radiators, ranges and

refrigerators. There is an increased risk of electric

shock if your body is earthed orgrounded.

c ) Do not expose power tools to rain or wet

conditions. Water entering a power tool will increase

the risk of electricshock.

d ) Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.

Keep cord away from heat, oil, sharp edges or

moving parts. Damaged or entangled cords increase

the risk of electricshock.

e ) When operating a power tool outdoors, use an

extension cord suitable for outdoor use. Use of

a cord suitable for outdoor use reduces the risk of

electricshock.

f ) If operating a power tool in a damp location

is unavoidable, use a ground fault circuit

interrupter (GFCI) protected supply. Use of a GFCI

reduces the risk of electricshock.

3) Personal Safety

a ) Stay alert, watch what you are doing and use

common sense when operating a power tool. Do

not use a power tool while you are tired or under

the influence of drugs, alcohol or medication. A

moment of inattention while operating power tools

may result in serious personalinjury.

b ) Use personal protective equipment. Always wear

eye protection. Protective equipment such as a dust

mask, non‑skid safety shoes, hard hat, or hearing

protection used for appropriate conditions will reduce

personalinjuries.

c ) Prevent unintentional starting. Ensure the switch

is in the off position before connecting to power

source and/or battery pack, picking up or carrying

the tool. Carrying power tools with your finger on the

switch or energizing power tools that have the switch

on invitesaccidents.

d ) Remove any adjusting key or wrench before

turning the power tool on. A wrench or a key left

attached to a rotating part of the power tool may result

in personalinjury.

e ) Do not overreach. Keep proper footing and

balance at all times. This enables better control of the

power tool in unexpectedsituations.

f ) Dress properly. Do not wear loose clothing or

jewelry. Keep your hair, clothing and gloves away

from moving parts. Loose clothes, jewelry or long

hair can be caught in movingparts.

g ) If devices are provided for the connection of dust

extraction and collection facilities, ensure these

are connected and properly used. Use of dust

collection can reduce dust‑relatedhazards.

ENGLISH

h ) Do not let familiarity gained from frequent use of

tools allow you to become complacent and ignore

tool safety principles. A careless action can cause

severe injury within a fraction of asecond.

4) Power Tool Use and Care

a ) Do not force the power tool. Use the correct power

tool for your application. The correct power tool

will do the job better and safer at the rate for which it

wasdesigned.

b ) Do not use the power tool if the switch does not

turn it on and off. Any power tool that cannot be

controlled with the switch is dangerous and must

berepaired.

c ) Disconnect the plug from the power source and/

or remove the battery pack, if detachable, from

the power tool before making any adjustments,

changing accessories, or storing power tools. Such

preventive safety measures reduce the risk of starting

the power toolaccidentally.

d ) Store idle power tools out of the reach of children

and do not allow persons unfamiliar with the

power tool or these instructions to operate the

power tool. Power tools are dangerous in the hands of

untrainedusers.

e ) Maintain power tools and accessories. Check

for misalignment or binding of moving parts,

breakage of parts and any other condition

that may affect the power tool’s operation. If

damaged, have the power tool repaired before

use. Many accidents are caused by poorly maintained

powertools.

f ) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are

less likely to bind and are easier tocontrol.

g ) Use the power tool, accessories and tool bits, etc.

in accordance with these instructions, taking

into account the working conditions and the

work to be performed. Use of the power tool for

operations different from those intended could result in

a hazardoussituation.

h ) Keep handles and grasping surfaces dry, clean

and free from oil and grease. Slippery handles and

grasping surfaces do not allow for safe handling and

control of the tool in unexpectedsituations.

5) Battery Tool Use and Care

a ) Recharge only with the charger specified by the

manufacturer. A charger that is suitable for one type

of battery pack may create a risk of fire when used with

another batterypack.

b ) Use power tools only with specifically designated

battery packs. Use of any other battery packs may

create a risk of injury andfire.

c ) When battery pack is not in use, keep it away

from other metal objects, like paper clips, coins,

keys, nails, screws or other small metal objects,

that can make a connection from one terminal to

another. Shorting the battery terminals together may

cause burns or afire.

d ) Under abusive conditions, liquid may be ejected

from the battery; avoid contact. If contact

accidentally occurs, flush with water. If liquid

contacts eyes, additionally seek medical help.

Liquid ejected from the battery may cause irritation

orburns.

e ) Do not use a battery pack or tool that is damaged

or modified. Damaged or modified batteries may

exhibit unpredictable behavior resulting in fire,

explosion or risk ofinjury.

f ) Do not expose a battery pack or tool to

fire or excessive temperature. Exposure to

fire or temperature above 265°F (130°C) may

causeexplosion.

g ) Follow all charging instructions and do not

charge the battery pack or tool outside the

temperature range specified in the instructions.

Charging improperly or at temperatures outside the

specified range may damage the battery and increase

the risk offire.

6) Service

a ) Have your power tool serviced by a qualified

repair person using only identical replacement

parts. This will ensure that the safety of the power tool

ismaintained.

b ) Never service damaged battery packs. Service

of battery packs should only be performed by the

manufacturer or authorized serviceproviders.

CUTOFF MACHINE SAFETY WARNINGS

a ) The guard provided with the tool must be securely

attached to the power tool and positioned for

maximum safety, so the least amount of wheel is

exposed towards the operator. Position yourself

and bystanders away from the plane of the

rotating wheel. The guard helps to protect operator

from broken wheel fragments and accidental contact

with wheel.

b ) Use only bonded reinforced or diamond cut‑off

wheels for your power tool. Just because an

accessory can be attached to your power tool, it does

not assure safeoperation.

c ) The rated speed of the accessory must be at least

equal to the maximum speed marked on the

power tool. Accessories running faster than their rated

speed can break and flyapart.

d ) Wheels must be used only for recommended

applications. For example: do not grind with the

side of cut‑off wheel. Abrasive cut‑off wheels are

intended for peripheral grinding, side forces applied to

these wheels may cause them toshatter.

e ) Always use undamaged wheel flanges that are of

correct diameter for your selected wheel. Proper

wheel flanges support the wheel thus reducing the

possibility of wheelbreakage.

f ) Do not use worn down reinforced wheels from

larger power tools. Wheels intended for a larger

ENGLISH

power tool are not suitable for the higher speed of a

smaller tool and mayburst.

g ) The outside diameter and the thickness of your

accessory must be within the capacity rating of

your power tool. Incorrectly sized accessories cannot

be adequately guarded orcontrolled.

h ) The arbour size of wheels and flanges must

properly fit the spindle of the power tool. Wheels

and flanges with arbour holes that do not match the

mounting hardware of the power tool will run out

of balance, vibrate excessively and may cause loss

ofcontrol.

i ) Do not use damaged wheels. Before each use,

inspect the wheels for chips and cracks. If power

tool or wheel is dropped, inspect for damage or

install an undamaged wheel. After inspecting

and installing the wheel, position yourself and

bystanders away from the plane of the rotating

wheel and run the power tool at maximum no

load speed for one minute. Damaged wheels will

normally break apart during this testtime.

j ) Wear personal protective equipment. Depending

on application, use face shield, safety goggles

or safety glasses. As appropriate, wear dust

mask, hearing protectors, gloves and shop apron

capable of stopping small abrasive or workpiece

fragments. The eye protection must be capable of

stopping flying debris generated by various operations.

The dust mask or respirator must be capable of

filtering particles generated by your operation.

Prolonged exposure to high intensity noise may cause

hearingloss.

k ) Keep bystanders a safe distance away from

work area. Anyone entering the work area must

wear personal protective equipment. Fragments

of workpiece or of a broken wheel may fly away and

cause injury beyond immediate area ofoperation.

l ) Hold the power tool by insulated gripping

surfaces only, when performing an operation

where the cutting accessory may contact hidden

wiring. Cutting accessory contacting a "live" wire may

make exposed metal parts of the power tool "live" and

could give the operator an electricshock.

m ) Never lay the power tool down until the accessory

has come to a complete stop. The spinning wheel

may grab the surface and pull the power tool out of

yourcontrol.

n ) Do not run the power tool while carrying it at your

side. Accidental contact with the spinning accessory

could snag your clothing, pulling the accessory into

yourbody.

o ) Regularly clean the power tool’s air vents. The

motor’s fan will draw the dust inside the housing and

excessive accumulation of powdered metal may cause

electricalhazards.

p ) Do not operate the power tool near flammable

materials. Sparks could ignite thesematerials.

q ) Do not use accessories that require liquid

coolants. Using water or other liquid coolants may

result in electrocution orshock.

FURTHER SAFETY INSTRUCTIONS FOR

ABRASIVE CUTTINGOFF OPERATIONS

Kickback and Related Warnings

Kickback is a sudden reaction to a pinched or snagged rotating

wheel, backing pad, brush or any other accessory. Pinching or

snagging causes rapid stalling of the rotating accessory which

in turn causes the uncontrolled power tool to be forced in the

direction opposite of the accessory’s rotation at the point of

thebinding.

For example, if an abrasive wheel is snagged or pinched by the

workpiece, the edge of the wheel that is entering into the pinch

point can dig into the surface of the material causing the wheel

to climb out or kick out. The wheel may either jump toward or

away from the operator, depending on direction of the wheel’s

movement at the point of pinching. Abrasive wheels may also

break under theseconditions.

Kickback is the result of power tool misuse and/or incorrect

operating procedures or conditions and can be avoided by

taking proper precautions as given below:

a ) Maintain a firm grip on the power tool and

position your body and arm to allow you to resist

kickback forces. Always use auxiliary handle, if

provided, for maximum control over kickback or

torque reaction during start‑up. The operator can

control torque reaction or kickback forces, if proper

precautions aretaken.

b ) Never place your hand near the rotating

accessory. Accessory may kickback over yourhand.

c ) Do not position your body in line with the

rotating wheel. Kickback will propel the tool in

direction opposite to the wheel’s movement at the

point ofsnagging.

d ) Use special care when working corners, sharp

edges etc. Avoid bouncing and snagging the

accessory. Corners, sharp edges or bouncing have a

tendency to snag the rotating accessory and cause loss

of control orkickback.

e ) Do not attach a saw chain, woodcarving blade,

segmented diamond wheel with a peripheral gap

greater than 10mm or toothed saw blade. Such

blades create frequent kickback and loss ofcontrol.

f ) Do not “jam” the wheel or apply excessive

pressure. Do not attempt to make an excessive

depth of cut. Overstressing the wheel increases the

loading and susceptibility to twisting or binding of

the wheel in the cut and the possibility of kickback or

wheelbreakage.

g ) When wheel is binding or when interrupting a cut

for any reason, switch off the power tool and hold

the power tool motionless until the wheel comes

to a complete stop. Never attempt to remove

the wheel from the cut while the wheel is in

motion otherwise kickback may occur. Investigate

ENGLISH

Additional Safety Warnings for Abrasive

Cutting-Off Operations:

a ) This power tool is intended to function as a cut‑off

tool. Read all safety warnings, instructions,

illustrations and specifications provided with

this power tool. Failure to follow all instructions

listed below may result in electric shock, fire and/or

seriousinjury.

b ) Operations such as grinding, sanding, wire

brushing, or polishing are not recommended to

be performed with this power tool. Operations for

which the power tool was not designed may create a

hazard and cause personalinjury Do not surface grind

with side of wheel.

c ) Do not use accessories which are not specifically

designed and recommended by the tool

manufacturer. Just because the accessory can

be attached to your power tool, it does not assure

safeoperation.

d ) The outside diameter and the thickness of your

accessory must be within the capacity rating of

your power tool. Incorrectly sized accessories cannot

be adequately guarded orcontrolled.

e ) The arbour size of wheels or flanges must

properly fit the spindle of the power tool.

Accessories with arbour holes that do not match the

mounting hardware of the power tool will run out

of balance, vibrate excessively and may cause loss

ofcontrol.

f ) When using segmented diamond wheels, use

only diamond wheels with a peripheral gap not

greater than 10mm and negative rakeangle.

g ) Set the depth of cut for no more than necessary.

The less wheel exposed, the less chance of binding

and kickback. Before cutting, be sure adjust shoe

assembly istight.

h ) Do not force the tool. Forcing a cut off tool reduces

control and cuttingefficiency.

i ) If guard is not tight in position, do notuse.

j ) Do not use toothedblades.

k ) Do not use this tool as a tablesaw.

l ) Firmly secure the workpiece.

Additional Safety Information

WARNING: Never modify the power tool or any part of

it. Damage or personal injury couldresult.

WARNING: ALWAYS use safety glasses. Everyday

eyeglasses are NOT safety glasses. Also use face or

dust mask if cutting operation is dusty. ALWAYS WEAR

CERTIFIED SAFETYEQUIPMENT:

• ANSI Z87.1 eye protection (CAN/CSA Z94.3),

• ANSI S12.6 (S3.19) hearing protection,

• NIOSH/OSHA/MSHA respiratoryprotection.

WARNING:

Some dust created by power sanding,

sawing, grinding, drilling, and other construction

activities contains chemicals known to the State

of California to cause cancer, birth defects or

other reproductive harm. Some examples of these

chemicalsare:

• lead from lead‑based paints,

• crystalline silica from bricks and cement and other

masonry products, and

• arsenic and chromium from

chemically‑treatedlumber.

Your risk from these exposures varies, depending on

how often you do this type of work. To reduce your

exposure to these chemicals: work in a well ventilated

area, and work with approved safety equipment, such

as those dust masks that are specially designed to filter

out microscopicparticles.

WARNING: Use of this tool can generate and/or

disperse dust, which may cause serious and permanent

respiratory or other injury. Always use NIOSH/OSHA

approved respiratory protection appropriate for

the dust exposure. Direct particles away from face

andbody.

WARNING: Always wear proper personal hearing

protection that conforms to ANSI S12.6 (S3.19)

during use. Under some conditions and duration

of use, noise from this product may contribute to

hearingloss.

• Wear protective clothing and wash exposed areas

with soap and water. Allowing dust to get into your

mouth, eyes, or lay on the skin may promote absorption

of harmfulchemicals. Direct particles away from face

andbody.

• Use the appropriate dust extractor vacuum to remove

the vast majority of static and airborne dust. Failure

to remove static and airborne dust could contaminate the

working environment or pose an increased health risk to

the operator and those in closeproximity.

• Use clamps or other practical ways to secure and

support the workpiece to a stable platform. Holding

the work by hand or against your body is unstable and may

lead to loss ofcontrol andinjury.

• Air vents often cover moving parts and should be

avoided. Loose clothes, jewelry or long hair can be caught

in movingparts.

and take corrective action to eliminate the cause of

wheelbinding.

h ) Do not restart the cutting operation in the

workpiece. Let the wheel reach full speed and

carefully re‑enter the cut. The wheel may bind,

walk up or kickback if the power tool is restarted in

theworkpiece.

i ) Support panels or any oversized workpiece to

minimize the risk of wheel pinching and kickback.

Large workpieces tend to sag under their own weight.

Supports must be placed under the workpiece near the

line of cut and near the edge of the workpiece on both

sides of thewheel.

j ) Use extra caution when making a “pocket cut”

into existing walls or other blind areas. The

protruding wheel may cut gas or water pipes, electrical

wiring or objects that can cause kickback.

ENGLISH

CAUTION: When not in use, place tool on its

side on a stable surface where it will not cause

a tripping or falling hazard. Some tools with large

battery packs will stand upright on the battery pack

but may be easily knockedover.

The label on your tool may include the following symbols. The

symbols and their definitions are asfollows:

V .......................... volts

Hz ........................hertz

min ...................... minutes

or DC ......direct current

....................... Class I Construction

(grounded)

…/min ..............per minute

BPM .................... beats per minute

IPM ..................... impacts per minute

OPM ....................

oscillations per minute

RPM ....................

revolutions per minute

sfpm ...................

surface feet per minute

SPM .................... strokes per minute

A ......................... amperes

W ........................watts

Wh ......................watt hours

Ah ....................... amp hours

or AC ...........alternating current

or AC/DC .... alternating or

direct current

...................... Class II Construction

(double insulated)

no .......................no load speed

n .........................rated speed

PSI.......................

pounds per square inch

......................earthing terminal

.....................safety alert symbol

..................... visible radiation–

do not stare into

the light

..................... wear respiratory

protection

..................... wear eye protection

..................... wear hearing

protection

..................... r

ead all documentation

.....................

do not expose to rain

BATTERIES AND CHARGERS

The battery pack is not fully charged out of the carton.

Before using the battery pack and charger, read the

safety instructions below and then follow charging

proceduresoutlined. When ordering replacement battery

packs, be sure to include the catalog number andvoltage.

• Do not store or use the tool and battery pack in

locations where the temperature may reach or

exceed 104°F (40°C) (such as outside sheds or metal

buildings in summer). For best life store battery packs in

a cool, drylocation.

NOTE: Do not store the battery packs in a tool with

the trigger switch locked on. Never tape the trigger

switch in the ONposition.

• Do not incinerate the battery pack even if it is severely

damaged or is completely worn out. The battery pack

can explode in a fire. Toxic fumes and materials are created

when lithium‑ion battery packs areburned.

• Do not expose a battery pack or appliance to ﬁre or

excessive temperature. Exposure to ﬁre or temperature

above 265°F (130°C) may causeexplosion.

• Follow all charging instructions and do not charge the

battery pack or appliance outside of the temperature

range specified in the instructions. Charging improperly or

at temperatures outside of the specified range may damage

the battery and increase the risk offire.

• If battery contents come into contact with the skin,

immediately wash area with mild soap and water. If

battery liquid gets into the eye, rinse water over the open

eye for 15minutes or until irritation ceases. If medical

attention is needed, the battery electrolyte is composed of a

mixture of liquid organic carbonates and lithiumsalts.

• Contents of opened battery cells may cause

respiratory irritation. Provide fresh air. If symptoms

persist, seek medicalattention.

• Battery liquid may be flammable if exposed to spark

orflame.

• Never attempt to open the battery pack for any

reason. If the battery pack case is cracked or

damaged, do not insert into the charger. Do not crush,

drop or damage the battery pack. Do not use a battery pack

or charger that has received a sharp blow, been dropped,

run over or damaged in any way (e.g., pierced with a nail,

hit with a hammer, stepped on). Damaged battery packs

should be returned to the service center forrecycling.

Storage Recommendations

The best storage place is one that is cool and dry, away

from direct sunlight and excess heat or cold. Store the fully

charged battery pack out of thecharger.

Battery Pack Cleaning Instructions

Dirt and grease may be removed from the exterior of the

battery pack using a cloth or soft non-metallic brush. Do not

use water or any cleaningsolutions.

Fuel Gauge Battery Packs (Fig.B)

Some battery packs include a fuel gauge. When the fuel

gauge button is pressed and held, the LED lights will

indicate the approximate level of charge remaining. This

does not indicate tool functionality and is subject to

variation based on product components, temperature, and

end-userapplication.

READ ALL INSTRUCTIONS

Important Safety Instructions for All

Battery Packs

WARNING: Read all safety warnings, instructions,

and cautionary markings for the battery pack,

charger and product. Failure to follow the

warnings and instructions may result in electric

shock, fire and/or seriousinjury.

• Do not charge or use the battery pack in explosive

atmospheres, such as in the presence of flammable

liquids, gases or dust. Inserting or removing the battery

pack from the charger may ignite the dust orfumes.

• NEVER force the battery pack into the charger. DO

NOT modify the battery pack in any way to fit into a

non‑compatible charger as battery pack may rupture

causing serious personal injury. Consult the chart at the

end of this manual for compatibility of batteries andchargers.

• Charge the battery packs only in

CRAFTSMANchargers.

• DO NOT splash or immerse in water or otherliquids.

• DO NOT allow water or any liquid to enter batterypack.

ENGLISH

Transportation

WARNING: Fire hazard. Do not store, carry, or

transport the battery pack so that metal objects

can contact exposed battery terminals. For

example, do not place the battery pack in aprons,

pockets, tool boxes, product kit boxes, drawers, etc.,

with loose nails, screws, keys, coins, hand tools, etc.

When transporting individual battery packs, make

sure that the battery terminals are protected and well

insulated from materials that could contact them and

cause a short circuit.

NOTE: Li‑ion battery packs should not be put

in checked baggage on airplanes and must be

properly protected from short circuits if they are in

carry‑onbaggage.

The RBRC® Seal

Please take your spent battery packs to an

authorized CRAFTSMAN service center or

to your local retailer for recycling. In some

areas, it is illegal to place spent battery

packs in the trash. You may also contact your local recycling

center for information on where to drop off the spent

battery pack. Do not place in curbside recycling. For more

information visit www.call2recycle.org or call the toll-free

number in the RBRC®Seal.

RBRC® is a registered trademark of Call 2Recycle,Inc.

• When operating a charger outdoors, always provide

a dry location and use an extension cord suitable

for outdoor use. Use of a cord suitable for outdoor use

reduces the risk of electricshock.

• An extension cord must have adequate wire size

(AWG or American Wire Gauge) for safety. The smaller

the gauge number of the wire, the heavier the cord and

thus the greater its capacity. An undersized cord will

cause a drop in line voltage resulting in loss of power and

overheating. The following table shows the correct size

to use depending on total length of all extension cords

plugged together, and nameplate ampere rating. If in

doubt, use the next heaviergauge.

Minimum Gauge for Cord Sets

Volts Total Length of Cord in Feet

(meters)

120V 25 (7.6) 50 (15.2) 100 (30.5) 150 (45.7)

Ampere Rating

American Wire Gauge

More Than Not More

Than

0 6 18 16 16 14

610 18 16 14 12

10 12 16 16 14 12

12 16 14 12 Not Recommended

• Do not place any object on top of the charger or place

the charger on a soft surface that might block the

ventilation slots and result in excessive internal heat.

Place the charger in a position away from any heat source.

The charger is ventilated through slots in the top and the

bottom of thehousing.

• Do not operate the charger with a damaged cord

orplug. Have them replacedimmediately.

• Do not operate the charger if it has received a sharp

blow, been dropped or otherwise damaged in any

way. Take it to an authorized servicecenter.

• Do not disassemble the charger; take it to an

authorized service center when service or repair

is required. Incorrect reassembly may result in a risk of

electric shock, electrocution orfire.

• The charger is designed to operate on standard

120V household electrical power. Do not attempt to

use it on any other voltage. This does not apply to the

vehicularcharger.

• Foreign materials of a conductive nature, such as, but

not limited to, grinding dust, metal chips, steel wool,

aluminum foil or any buildup of metallic particles

should be kept away from the charger cavities and

ventilation slots.

• Always unplug the charger from the power supply

when there is no battery pack in thecavity.

Charging a Battery (Fig.C, D)

1. Plug the charger into an appropriate outlet.

2. Insert and fully seat battery pack1. Charging light(s) will

continuously blink whilecharging.

Important Safety Instructions for All

Battery Chargers

WARNING: Read all safety warnings, instructions,

and cautionary markings for the battery pack,

charger and product. Failure to follow the

warnings and instructions may result in electric

shock, fire and/or seriousinjury.

• DO NOT attempt to charge the battery pack with

any chargers other than a CRAFTSMAN charger.

CRAFTSMAN chargers and battery packs are specifically

designed to worktogether.

• These chargers are not intended for any uses other

than charging CRAFTSMAN rechargeable battery

packs. Charging other types of battery packs may cause

them to overheat and burst, resulting in personal injury,

property damage, fire, electric shock orelectrocution.

• Do not expose the charger to rain orsnow.

• Do not allow water or any liquid to entercharger.

• Pull by the plug rather than the cord when

disconnecting the charger. This will reduce the risk of

damage to the electric plug andcord.

• Make sure that the cord is located so that it will not

be stepped on, tripped over or otherwise subjected to

damage orstress.

• Do not use an extension cord unless it is absolutely

necessary. Use of improper extension cord could result in

risk of fire, electric shock orelectrocution.

ENGLISH

3. Charging is complete when the green charging light(s)

remain(s) continuously ON. Battery pack can be left in

charger orremoved.

WARNING:

Only charge batteries in air temperature over

40° F (4.5° C) and below 104° F (40°C).

4. Charger will not charge a faulty battery pack, which may

be indicated by the charging light(s) staying OFF. Take

charger and battery pack to an authorized service center

if light(s) stay(s)OFF.

NOTE: Refer to label near charging light(s) on charger for

blinkpatterns.

NOTE: To remove the battery pack, some chargers

require the battery pack release button2 to bepressed.

Hot/Cold Pack Delay

When the charger detects a battery pack that is too hot

or too cold, it automatically starts a Hot/Cold Pack Delay,

suspending charging until the battery pack has reached an

appropriate temperature. The charger then automatically

switches to the pack charging mode. This feature ensures

maximum battery packlife.

A cold battery pack may charge at a slower rate than a warm

batterypack.

The hot/cold pack delay will be indicated by the green

light(s) continuing to blink but with the red light

continuously ON. Once the battery pack has reached an

appropriate temperature, the red light will turn OFF and the

charger will resume the chargingprocedure.

Electronic Protection System

Li-ion tools are designed with an Electronic Protection

System that will protect the battery pack against overloading,

overheating or deep discharge. The tool will automatically

turn off and the battery pack will need to berecharged.

Important Charging Notes

1. Longest life and best performance can be obtained if

the battery pack is charged when the air temperature is

between 65° F – 75° F (18° C– 24° C). DO NOT charge

when the battery pack is below 40° F (4.5° C), or above

104° F (40° C). This is important and will prevent serious

damage to the batterypack.

2. The charger and battery pack may become warm to the

touch while charging. This is a normal condition, and

does not indicate a problem. To facilitate the cooling of

the battery pack after use, avoid placing the charger or

battery pack in a warm environment such as in a metal

shed or an uninsulatedtrailer.

3. If the battery pack does not charge properly:

a. Check operation of receptacle by plugging in a lamp

or other appliance;

b. Check to see if receptacle is connected to a light

switch which turns power off when you turn out

thelights;

c. If charging problems persist, take the tool, battery

pack and charger to your local servicecenter.

4. You may charge a partially used pack whenever you

desire with no adverse effect on the batterypack.

Wall Mounting

Some CRAFTSMAN chargers are designed to be wall

mountable or to sit upright on a table or work surface.If wall

mounting, locate the charger within reach of an electrical

outlet, and away from a corner or other obstructions which

may impede air flow. Use the back of the charger as a

template for the location of the mounting screws on the wall.

Mount the charger securely using drywall screws (purchased

separately) at least 1” (25.4mm) long, with a screw head

diameter of 0.28–0.35” (7–9mm), screwed into wood to an

optimal depth leaving approximately 7/32” (5.5 mm) of the

screw exposed. Align the slots on the back of the charger

with the exposed screws and fully engage them in theslots.

NOTE: Do not attempt to mount CMCB101 charger under a

bench ortable.

NOTE: Only mount CMCB101 charger with the charging

lights pointed upward toward theceiling.

VersaTrack™

WARNING: Do not charge batteries while charger is

hung onTrackwall.

CRAFTSMAN chargers, except the CMCB101, can

be stored on CRAFTSMAN VersaTrack™ Trackwall.

Hooks and accessories are sold separately. Please

refer to the VersaTrack™ Trackwall accessory sheet for

furtherinformation.

NOTE: The CMCB101 charger is not CRAFTSMAN VersaTrack™

Trackwallcompatible.

SAVE THESE INSTRUCTIONS FOR

FUTURE USE

ASSEMBLY AND ADJUSTMENTS

WARNING:

To reduce the risk of serious personal

injury, turn unit off and

remove the battery pack

before making any adjustments or removing/

installing attachments or accessories. An accidental

start‑up can causeinjury.



WARNING: Wheels, cutting material and metal

components on the tool such as gearcase, shoe and

guard may be hot during or after continued use. Use

caution when approaching these areas.

Wheels

WARNING: To reduce the risk of injury, only use wheels

that are no greater than 3" (76mm) in diameter, have

an inner diameter of 3/8” (or 7/16” if using adapter

ring), and without cutting teeth. Thickness of wheel not

to exceed 0.09” (2.2mm). Never force a wheel onto the

machine or alter the size of the arborhole.

A dull wheel will cause slow inefficient cutting, overload the

motor, could cause excessive splintering, and could increase

Charger Cleaning Instructions

WARNING:Shock hazard. Disconnectthe charger

from the AC outlet before cleaning. Dirt and grease

may be removed from the exterior of the charger using

a cloth or soft non‑metallic brush. Do not use water or

any cleaningsolutions.

ENGLISH

the possibility of kickback. Please refer to the table below to

determine the correct wheel for yourapplication.

Wheel type Application

Diamond** Multi‑Material

Wheel

Drywall, fiber cement, plastic, steel, non

ferrous materials

Bonded Reinforced Wheel Steel, stainless steel, non‑ferrous materials

Diamond** Tile Wheel Ceramic Tile, Porcelain and Granite/Marble/

Stone

**This blade uses manufactured diamonds engineered

forcutting.

NOTE: Bonded Reinforced wheels are composed of abrasive

grains which are held tightly together by a bonding agent

and typically reinforced with a woven material.

center of the 7/16" wheel when assembled. Refer to

Fig.F1.

6. Slip wheel over spindle. Make sure wheel goes over pilot

diameter of innerflange.

NOTE: When installing diamond wheels, always match

direction of rotation of the wheel to the desired direction

of rotation of the tool.

7. Slip on outer flange with the flat side towards the wheel.

NOTE: The text "LOOSEN TIGHTEN" will be visible when

installedcorrectly.

8. Start threading on spindle screw counterclockwise which

will self align outer flange. Make sure the wheel is fitted

in the correctorientation.

9. Depress and hold spindle lock button and tighten

spindle screw with hex wrench. Do not overtighten

spindlescrew.

10. Release spindle lock button and turn wheel by hand to

ensure it is properly centered. The wheel should not hit

the shoe, guard or spindle screw. The spindle screw and

flanges should betight.

NOTE: Do not run tool with the spindle lock engaged.

Always allow motor to come to a complete stop before

engaging the spindle lock.

Installing/Replacing Wheels

(Fig. A, F1, F2, L, M)

WARNING: Burn Hazard. Sharp parts. ALWAYS wear

gloves when changing wheels. Wheels have sharp

edges or may get extremely hot during operation, and

may damage barehands.

WARNING: To reduce the risk of injury, only use wheels

that are no greater than 3" (76mm) in diameter, have

an inner diameter of 3/8” (or 7/16” if using adapter

ring), and without cutting teeth. Thickness of wheel not

to exceed 0.09” (2.2mm). Never force a wheel onto the

machine or alter the size of the arborhole.

WARNING: Since accessories, other than those

offered by CRAFTSMAN , have not been tested with

this product, use of such accessories with this tool

could be hazardous. To reduce the risk of injury, only

CRAFTSMAN recommended accessories should be

used with thisproduct.

WARNING: Failure to properly seat the flanges and/

or wheel could result in serious injury (or damage to the

tool or wheel).

1. Remove thebattery.

2. Lay unit on a firm surface, with the spindle15

facingupward.

3. Hold spindle lock button6 to keep the spindle

fromturning. Spindle threads are lefthand.

4. Using supplied 6mm hex wrench 12, rotate clockwise

to remove spindle screw20, outer flange19, and used

wheel18 if one is installed. Leave inner flange16

inplace.

NOTE: Hex wrench is magnetically secured.

NOTE: It is possible that the inner flange and outer

flange may stick together. Be sure to keep both flanges

seperated during the wheel installation process. Refer

to Fig. F2 showing the correct order of the flanges and

wheel installed over the spindle.

5. Ensure inner flange is installed over the spindle.

NOTE: Your tool comes provided with a 7/16" arbor

adapter17 which should only be used when installing

a 7/16" wheel. The 7/16" arbor adapter is not to be used

with the wheels provided with this tool. When installing

7/16" wheels, place the 7/16" arbor adaptorover the

innerflange. The 7/16" arbor adapter will fit inside the

Adjusting the Rotatable Guard Angle (Fig. G)

WARNING: Remove battery first. To reduce the risk

of injury, ALWAYS adjust the guard to provide the

best control and protection. ALWAYS wear gloves to

protect your hands when adjusting theguard as the

guard may get hot.

WARNING: Adjust the position of the guard to provide

the maximum protection from loose particles and

sparks thrown from the wheel.

CAUTION: Guard must be used with all cutting wheels.

1. Remove thebattery.

2. Grasp the rotatable guard11firmly and rotate until it

snaps securely into one of three positions.

Mounting, Removing the Shoe (Fig.A, J1)

Your cut off tool comes pre-assembled with the shoe9

mounted to the rotatable guard11.

To Remove the Shoe

1. Remove thebattery pack1.

2. Loosen the depth adjustment knob10counterclockwise.

3. Remove the depth adjustment knob and remove shoe

from the rotatableguard.

To Mount the Shoe

1. Remove thebattery pack.

2. Install shoe onto the back of the rotatable guard, aligning

slot29 to threaded hole25 on guard. Refer to Fig.J1.

3. Install and rotate the depth adjustment knob clockwise

to tighten.

NOTE: The shoe is not required for use with this tool. For

best performance the shoe is recommended for more

stability when cutting on a flatsurface.

ENGLISH

Attaching the Dust Port Adaptor (Fig.A, I)

A dust port adaptor8 comes available for use with this

tool. This accessory connects directly to the tool's rotatable

guard11 .

1. Remove the battery pack1.

2. Friction fit the dust port adaptor8 onto the dust port

hole23 located near the front tip of the rotatable guard.

Attaching an AirLock™ Compatible Dust

Extractor (Fig.A, I)

(Sold Separately)

WARNING: Do not use dust extraction when cutting

metal. Swarf from metal cutting may be hot and may

spark which can melt vacuum hoses and may cause a

fire inside thevacuum.

WARNING: When using dust extraction, empty

vacuum before work begins and often during work.

Use care in disposing of dust. Materials in fine dust can

beexplosive.

The dust port adaptor8 allows you to connect the tool

to an external dust extractor using a AirLock™ connection

system (soldseparately), or a standard 32 mm dust extractor

fitment. The AirLock™ allows for a fast, secure connection

between the AirLock™ connector21 and your tool's dust

port adaptor.

1. Remove thebattery pack1.

2. Ensure the collar on the AirLock™ connector is in the

unlock position. (Refer to FigureI.) Align notches22 on

collar and AirLock™ connector as shown for unlock and

lockpositions.

3. Push the AirLock™ connector onto the connection point

of the dust port adaptor. (Refer to Fig. I)

4. Rotate the collar to the lockedposition.

NOTE: The ball bearings inside collar lock into slot and

secure the connection.The power tool is now securely

connected to the dustextractor.

OPERATION

WARNING: To reduce the risk of serious personal

injury, turn unit off and remove the battery pack

before making any adjustments or removing/

installing attachments or accessories. An

accidental start‑up can causeinjury.

Proper Hand Position (Fig. H)

WARNING: To reduce the risk of serious personal injury,

ALWAYS use proper hand position asshown.

WARNING: To reduce the risk of serious personal

injury, ALWAYS hold securely in anticipation of a

suddenreaction.

WARNING: Keep your free hand far from

cuttingaction. Do not reach underneath the workpiece.

Proper hand position requires one hand on the main

handle3.

Installing and Removing the Battery Pack

(Fig.E)

WARNING: Ensure the tool/appliance is in the off

position before inserting the batterypack.

NOTE: For best results, make sure your battery pack is

fullycharged.

1. To install the battery pack1 into the tool handle, align

the battery pack with the rails inside the tool’s handle

and slide it into the handle until the battery pack is firmly

seated in the tool and ensure that it does notdisengage.

2. To remove the battery pack from the tool, press the

battery pack release button2 and firmly pull the battery

pack out of the tool handle. Insert it into the charger as

described in the charger section of thismanual.

Variable Speed Trigger (Fig. A)

The tool is turned on and off by pulling and releasing the

variable speed trigger 4 . The variable speed trigger permits

speed control—the farther the trigger is depressed, the

higher the speed of the tool.

Adjusting the Depth of Cut (Fig.J2)

1. Loosen the depth adjustment knob10 and slide the

shoe9 up or down. Adjust the cutting depth to the

thickness of the workpiece. Less than 1/4" of the wheel

should be visible below theworkpiece.

2. After depth of cut is selected tighten the depth

adjustment knob

LED Worklight (Fig.A)

The LED worklight13 will activate when the variable speed

trigger4 is depressed, and will automatically turn off

20seconds after the variable speed trigger is released. If the

variable trigger switch remains depressed, the LED worklight

will remainon.

NOTE: The LED worklight is for lighting the immediate work

surface and is not intended to be used as aflashlight.

Forward/Reverse/Lock Off Button

(Fig.A, K1–K2)

CAUTION: Before changing the position of the control

button, be sure the trigger isreleased.

Your cut-off tool is equipped with a forward/reverse/lock off

button5. There is a wheel direction label24 located above

the main handle3 that will help to identify the current

direction mode of the tool. Some applications or accessories

may require the tool to be run in forward or reverse. When

making a cut, select the direction of cut that allows the tool

to be pushed away from your body. Always operate tool in

correct rotation for wheel selected.

1. Forward (counterclockwise rotation) — Located on the

right side of the tool near the variable speed trigger4,

push the forward/reverse/lock off button5 to the far

left. Refer to Fig. K1. The forward direction of the wheel

is also noted by the direction indicator7 located on the

rotatable guard11. Refer to Fig. A.

ENGLISH

‑If excessive chipping of the tile is observed, user may

operate tool at slower speed using variable speed

trigger to achieve a cleanercut.

‑Cutting tile will generate debris. Guard position may

be adjusted to deflect debris away fromuser.

Cutting Plastic

‑Take frequent breaks to allow wheel to cooldown.

‑If melted material or debris becomes adhered to

blade, shoe or guard: Release trigger. Allow unit to

rest and material to cool. Remove battery. Remove

debris. Ensure all areas around wheel including inside

of guard is clear of debris. Resume cuttingoperation.

Cutting Metals

Observe the following to avoid potential hazards when

cuttingmetals.

‑During and shortly after cutting operation the

material, wheel and metal components on the tool

such as gearcase, guard and shoe may gethot.

‑Allow these areas to cool before touching to

avoidinjury.

‑Cutting metal will generate sparks. Guard position

may be adjusted to deflect sparks and debris away

fromuser.

‑Cutting material and cutting wheel may have sharp

or jagged edges after cutting operation. Wear gloves

and use caution when touching theseareas.

To Operate (Fig.A, H)

CAUTION: Before attempting to start, grasp

toolfirmly.

WARNING: To reduce the risk of injury, DO NOT use a

toothed blade.

WARNING: This tool is intended to be used dry.

If water cooling is necessary, use a spray bottle

with clean water to lightly wet surface only, avoid

over‑wetting the workpiece. NEVER immerse your tool

or battery pack in any liquid or allow liquid insidethem.

WARNING: Wheels used for cutting may break or kick

back if they bend or twist while the tool is being used to

do cut‑offwork.

WARNING: Do not bang or bump a cut‑off wheel

when starting or during acut.

1. Grasp main handle3firmly.

2. Line up wheel18with material to be cut. Be sure

nothing is near or in line with thewheel.

3. Depress and hold the variable speed trigger4. Slowly

feed the wheel into the workpiece with firm even

pressure, allowing the tool to do the work. Do not force

the cut off tool through the workpiece. Forcing a cut off

tool can cause kickback. For maximum efficiency and

wheel life, keep the wheel speedhigh.

4. While cutting, if using the shoe, keep the shoe against

the workpiece and maintain a firm grip.

NOTE: If making a partial cut, restarting a cut, or

correcting cut direction, allow the wheels to come to

a complete stop. To resume cutting, pull the variable

speed trigger and re-enter the cutslowly.

5. To stop tool, release the variable speed trigger.

Transportation and Storage

During transportation and storage lock the variable speed

trigger with the lock-offbutton. Refer to the Forward/

Reverse/Lock Off Button section.

Remove the battery pack during the toolstorage.

MAINTENANCE

WARNING: To reduce the risk of serious personal

injury, turn unit off and remove the battery pack

before making any adjustments or removing/

installing attachments or accessories. An

accidental start‑up can causeinjury.

Your CRAFTSMAN power tool has been designed to operate

over a long period of time with a minimum of maintenance.

Continuous satisfactory operation depends upon proper tool

care and regularcleaning.

Accessories

WARNING:

Since accessories, other than those

offered by

CRAFTSMAN

, have not been tested with

this product, use of such accessories with this product

could be hazardous. To reduce the risk of injury, only

CRAFTSMAN

recommended accessories should be used

with thisproduct.

WARNING:

Handle and store all abrasive wheels

carefully to prevent damage from thermal shock, heat,

mechanical damage, etc. Store in a dry protected area

free from high humidity, freezing temperatures or

extreme temperature changes.

2. Reverse (clockwise rotation) — Located on the left side

of the tool near the variable speed trigger4 , push the

forward/reverse/lock off button5 to the far right. Refer

to Fig. K2. The reverse direction of the wheel is also noted

by the direction indicator7 located on the rotatable

guard11.Refer to Fig. A.

3. The center position of the forward/reverse/lock off

button locks the tool in the off position. When locked the

variable speed trigger cannot be depressed.

NOTE: Keep the button in the center locked position when

the tool is not in use or when being transported.

General Tips for Cutting Materials

‑For best control, user cutting direction should be

opposite wheel rotation. Example: When making a

cut away from user by pushing the tool forward, set

wheel rotation to reverse/clockwise direction.

‑Be sure that the wheel is at full speed before

continuing a cut.

‑Allow the wheel to come to a complete stop before

raising the wheel out of thematerial.

Cutting Tile

‑To reduce overheating of cutting wheel or

workpiece, user may lightly wetsurface.

ENGLISH

Cleaning

WARNING: Blow dirt and dust out of all air vents with

clean, dry air at least once a week. To minimize the risk

of eye injury, always wear ANSI Z87.1 approved eye

protection when performing thisprocedure.

WARNING:

Never use solvents or other harsh chemicals

for cleaning the non‑metallic parts of the tool. These

chemicals may weaken the plastic materials used in

these parts. Use a cloth dampened only with water and

mild soap. Never let any liquid get inside the tool; never

immerse any part of the tool into aliquid.

Repairs

The charger and batteries are notserviceable. There are no

serviceable parts inside the charger or batterypack.

WARNING: To assure product SAFETY and

RELIABILITY, repairs, maintenance and adjustment

(including brush inspection and replacement, when

applicable) should be performed by a factory service

center or an authorized service center. Always use

identical replacementparts.

VersaTrack™ (Fig. N)

Optional accessory, sold separately.

WARNING: To reduce the risk of serious personal

injury, turn unit off and remove the battery pack

before making any adjustments or removing/

installing attachments or accessories. An

accidental start‑up can causeinjury.

WARNING: To reduce the risk of serious personal

injury, do not use a damaged VersaTrack™ hang hook

or VersaTrack™ Trackwall. A damaged VersaTrack™

hang hook or VersaTrack™ Trackwall will not support

the weight of thetool.

WARNING: To reduce the risk of serious personal

injury, ensure the screw holding the VersaTrack™ hang

hook is securelytightened.

WARNING: To reduce the risk of serious personal

injury, DO NOT suspend tool overhead or suspend

objects from the hang hook. ONLY suspend tool on the

VersaTrack™ Trackwall using the hanghook.

WARNING: The Versatrack™ integral hang hook is not

a belthook.

WARNING: Ensure that the tool weight does not

exceed the maximum rated weight of 20lb (9 kg) for

the selected VersaTrack™hook.

WARNING: When hanging objects on a VersaTrack™

Trackwall rail, adequately space the tools in order to

not exceed 75lb (35 kg) per linearfoot.

IMPORTANT: When attaching the VersaTrack™ hang

hook, use only the screw that is provided. Be sure to

securely tighten the screw. VersaTrack™ accessories

mount compatible tools securely to the VersaTrack™

Trackwallsystem.

1. Turn the tool off, remove the battery pack

andaccessories.

CAUTION: Any product with exposed cutting teeth

must have them covered securely if it is to be on

theVersaTrack™Trackwall.

2. Attach the VersaTrack™ hang hook28 on thetool.

a. Place the VersaTrack™ hang hook onto the accessory

attacment location14 at the base of thetool.

b. Use a screwdriver to secure the VersaTrack™ hang

hook with the provided screw27. Do not use any

other screw forthis.

NOTE: VersaTrack™ accessories for use with your tool are

available at extra cost from your local dealer or authorized

service center. If you need assistance in locating any

accessory, please contact CRAFTSMAN, call 1-888-331-4569.

WARNING: To reduce the risk of serious personal

injury, DO NOT suspend tool overhead or suspend

objects from the belt hook. ONLY hang tool’s belt hook

from a workbelt.

WARNING: To reduce the risk of serious personal

injury, ensure the screw holding the belt hook issecure.

CAUTION: To reduce the risk of personal injury

or damage, DO NOT use the belt hook to hang

thetool.

IMPORTANT: When attaching or replacing the belt hook26,

use only the screw27 that is provided. Be sure to securely

tightenscrew.

If the belt hook is not desired at all, it can be removed from

thetool.

1. Place the belt hook onto the accessory attachment

location14 at the base of thetool.

2. Use a screwdriver to secure the belt hook with the

provided screw. Do not use any other screw forthis.

To remove the belt hook, remove the screwthat holds the

belt hook inplace.

Thank you for your purchase. Register your product nowfor:

• WARRANTY SERVICE: Registering your product will help

you obtain more efficient warranty service in case there is

a problem with yourproduct.

• CONFIRMATION OF OWNERSHIP: In case of

an insurance loss, such as fire, flood or theft, your

registration of ownership will serve as your proof

ofpurchase.

• FOR YOUR SAFETY: Registering your product will allow

us to contact you in the unlikely event a safety notification

is required under the Federal Consumer SafetyAct.

• Register online at www.craftsman.com/support.

Belt Hook(Fig.O)

Optional accessory, sold separately.

WARNING: To reduce the risk of serious personal

injury, turn tool off and disconnect battery pack

before making any adjustments or removing/

installing attachments oraccessories.

Recommended accessories for use with your product are

available at extra cost from your local dealer or authorized

service center. If you need assistance in locating any

accessory, please contact CRAFTSMAN. Call 1-888-331-4569.

ENGLISH

Three-Year Limited Warranty

For warranty terms, go to https://www.craftsman.com/

support/warranty.

To request a written copy of the warranty terms, contact:

Customer Service at CRAFTSMAN, 701East Joppa Road,

Towson, MD 21286or call 1-888-331-4569.

LATIN AMERICA: This warranty does not apply to products

sold in Latin America. For products sold in Latin America,

see country-specific warranty information contained in

the packaging, call the local company, or see website for

warrantyinformation.

FREE WARNING LABEL REPLACEMENT: If your warning

labels become illegible or are missing, call 1-888-331-4569

for a freereplacement.

FRANÇAIS

Le terme « outil électrique » cité dans les avertissements

se rapporte à votre outil électrique à alimentation sur

secteur (avec fil) ou par piles (sansfil).

1) Sécurité du lieu de travail

a ) Tenir l’aire de travail propre et bien éclairée.

Les lieux encombrés ou sombres sont propices

auxaccidents.

b ) Ne pas faire fonctionner d’outils électriques

dans un milieu déflagrant, tel qu’en présence de

liquides, de gaz ou de poussières inflammables.

Les outils électriques produisent des étincelles qui

pourraient enflammer la poussière ou lesvapeurs.

c ) Éloigner les enfants et les personnes à proximité

pendant l’utilisation d’un outil électrique. Une

distraction pourrait en faire perdre la maîtrise

àl’utilisateur.

2) Sécurité en matière d’électricité

a ) Les fiches des outils électriques doivent

correspondre à la prise. Ne jamais modifier la

fiche d’aucune façon. Ne jamais utiliser de fiche

d’adaptation avec un outil électrique mis à la

terre. Le risque de choc électrique sera réduit par

l’utilisation de fiches non modifiées correspondant

àlaprise.

b ) Éviter tout contact physique avec des surfaces

mises à la terre comme des tuyaux, des radiateurs,

des cuisinières et des réfrigérateurs. Le risque de

choc électrique est plus élevé si votre corps est mis

àlaterre.

c ) Ne pas exposer les outils électriques à la pluie ou

à l’humidité. La pénétration de l’eau dans un outil

électrique augmente le risque de chocélectrique.

d ) Ne pas utiliser le cordon de façon abusive. Ne

jamais utiliser le cordon pour transporter, tirer

ou débrancher un outil électrique. Tenir le

cordon éloigné de la chaleur, de l’huile, des bords

tranchants et des pièces mobiles. Les cordons

endommagés ou enchevêtrés augmentent les risques

de chocélectrique.

e ) Pour l’utilisation d’un outil électrique à l’extérieur,

se servir d’une rallonge convenant à cette

application. L’utilisation d’une rallonge conçue pour

l’extérieur réduira les risques de chocélectrique.

f ) S’il est impossible d’éviter l’utilisation d’un

outil électrique dans un endroit humide,

brancher l’outil dans une prise ou sur un circuit

d’alimentation dotés d’un disjoncteur de fuite à

la terre (GFCI). L’utilisation de ce type de disjoncteur

réduit les risques de chocélectrique.

3) Sécurité personnelle

a ) Être vigilant, surveiller le travail effectué et faire

preuve de jugement lorsqu’un outil électrique est

utilisé. Ne pas utiliser d’outil électrique en cas de

fatigue ou sous l’influence de drogues, d’alcool ou

de médicaments. Un simple moment d’inattention en

utilisant un outil électrique peut entraîner des blessures

corporellesgraves.

AVERTISSEMENTS GÉNÉRAUX SUR LA

SÉCURITÉ DES OUTILS

AVERTISSEMENT : lisez tous les avertissements de

sécurité, toutes les instructions, les illustrations

et les caractéristiques fournis avec cet outil

électrique. Ne pas suivre toutes les instructions

comprises aux présentes peut conduire à un choc

électrique, un incendie et/ou des blessuresgraves.

CONSERVER TOUS LES

AVERTISSEMENTS ET TOUTES

LES DIRECTIVES POUR UN

USAGEULTÉRIEUR.

Définitions: symboles et mentions d'alerte

de sécurité

Cette notice d'utilisation utilise les symboles et les mentions

d'alerte de sécurité suivants afin de vous alerter sur les

situations dangereuses et les risques de blessures ou de

dégâtsmatériels.

DANGER: indique une situation de risque imminent

qui engendre, si elle n'est pas évitée, la mort ou de

gravesblessures.

AVERTISSEMENT: indique une situation de risque

potentiel qui pourrait engendrer, si elle n'est pas évitée,

la mort ou de gravesblessures.

ATTENTION: indique une situation de risque potentiel

qui peut engendrer, si elle n'est pas évitée, des

blessures bénignes oumodérées.

REMARQUE: indique une pratique n'entraînant

aucun risque de blessures mais qui, si elle n'est pas

évitée, peut entraîner des dommagesmatériels.

(Utilisé sans mention) Indique un message lié à lasécurité.

Utilisation prévue

Votre outil de coupe est un outil électrique destiné à des

applicationsprofessionnelles.

NE PAS utiliser en présence de liquides ou de

gazinflammables.

Votre outil de coupe est un outil électriqueprofessionnel.

NE PAS laisser les enfants toucher l’outil. Une supervision

est requise lorsque des utilisateurs inexpérimentés utilisent

cetoutil.

Français (traduction de la notice d’instructions originale)

AVERTISSEMENT: lisez tous les avertissements

de sécurité et toutes les instructions. Ne pas suivre

les avertissements et les instructions peut entraîner un

choc électrique, un incendie et/ou des blessuresgraves.

AVERTISSEMENT: pour réduire le risque de blessure,

lisez le guided’utilisation.

FRANÇAIS

son mode d’emploi d’utiliser cet outil. Les outils

électriques deviennent dangereux entre les mains

d’utilisateursinexpérimentés.

e ) Gardez les poignées et surfaces d’emprise propres

et libres de tout produit lubrifiant. Vérifier si les

pièces mobiles sont mal alignées ou coincées,

si des pièces sont brisées ou présentent toute

autre condition susceptible de nuire au bon

fonctionnement de l’outil électrique. En cas de

dommage, faire réparer l’outil électrique avant

toute nouvelle utilisation. Beaucoup d’accidents

sont causés par des outils électriques malentretenus.

f ) S’assurer que les outils de coupe sont aiguisés et

propres. Les outils de coupe bien entretenus et affûtés

sont moins susceptibles de se coincer et sont plus

faciles àmaîtriser.

g ) Utiliser l’outil électrique, les accessoires, les forets,

etc. conformément aux présentes directives en

tenant compte des conditions de travail et du

travail à effectuer. L’utilisation d’un outil électrique

pour toute opération autre que celle pour laquelle il a

été conçu estdangereuse.

h ) Garder vos mains et les surfaces de prise sèches,

propres et libres de graisse et de poussière. Les

mains et les surfaces de prise glissante ne permettent

pas la manutention et le contrôle sécuritaires de l’outil

dans les situationsimprévues.

5) Utilisation et entretien du bloc‑piles

a ) Ne recharger l’outil qu’au moyen du chargeur

précisé par le fabricant. L’utilisation d’un chargeur

qui convient à un type de bloc‑piles risque de

provoquer un incendie s’il est utilisé avec un autre type

de bloc‑piles.

b ) Utiliser les outils électriques uniquement avec

les blocs‑piles conçus à cet effet. L’utilisation de

tout autre bloc‑piles risque de causer des blessures ou

unincendie.

c ) Lorsque le bloc‑piles n’est pas utilisé, le tenir

éloigné des objets métalliques, notamment

des trombones, de la monnaie, des clés, des

clous, des vis ou autres petits objets métalliques

qui peuvent établir une connexion entre les

deux bornes. Le court‑circuit des bornes du bloc‑piles

risque de provoquer des brûlures ou unincendie.

d ) En cas d’utilisation abusive, le liquide peut gicler

hors du bloc‑piles; éviter tout contact avec ce

liquide. Si un contact accidentel se produit, laver

à grande eau. Si le liquide entre en contact avec

les yeux, obtenir également des soins médicaux.

Le liquide qui gicle hors du bloc‑piles peut provoquer

des irritations ou desbrûlures.

e ) Ne pas utiliser de bloc‑piles ou outil qui a été

endommagé ou modifié. Les unités endommagées

ou modifiées peuvent avoir une réaction imprévisible

résultant en un incendie, une explosion ou un potentiel

deblessure.

f ) Ne pas exposer de bloc‑piles ou l’outil aux

flammes ou à des températures excessives.

L’exposition aux flammes ou à une température

b ) Utiliser des équipements de protection

individuelle. Toujours porter une protection

oculaire. L’utilisation d’équipements de protection

comme un masque antipoussière, des chaussures

antidérapantes, un casque de sécurité ou des

protecteurs auditifs lorsque la situation le requiert

réduira les risques de blessurescorporelles.

c ) Empêcher les démarrages intempestifs. S’assurer

que l’interrupteur se trouve à la position d’arrêt

avant de relier l’outil à une source d’alimentation

et/ou d’insérer un bloc‑piles, de ramasser ou de

transporter l’outil. Transporter un outil électrique

alors que le doigt repose sur l’interrupteur ou brancher

un outil électrique dont l’interrupteur est à la position

de marche risque de provoquer unaccident.

d ) Retirer toute clé de réglage ou clé avant de

démarrer l’outil. Une clé ou une clé de réglage

attachée à une partie pivotante de l’outil électrique

peut provoquer des blessurescorporelles.

e ) Ne pas trop tendre les bras. Conserver son

équilibre en tout temps. Cela permet de mieux

maîtriser l’outil électrique dans les situationsimprévues.

f ) S’habiller de manière appropriée. Ne pas porter

de vêtements amples ni de bijoux. Garder les

cheveux, les vêtements et les gants à l’écart des

pièces mobiles. Les vêtements amples, les bijoux ou

les cheveux longs risquent de rester coincés dans les

piècesmobiles.

g ) Si des composants sont fournis pour le

raccordement de dispositifs de dépoussiérage

et de ramassage, s’assurer que ceux‑ci sont bien

raccordés et utilisés. L’utilisation d’un dispositif de

dépoussiérage peut réduire les dangers engendrés par

lespoussières.

h ) Ne pas laisser votre connaissance acquise suite

l’utilisation fréquente des outils vous permettre

de baisser la garde et ignorer les principes de

sécurité de l’outil. Un acte irréfléchi peut causer une

blessure grave en une fraction deseconde.

4) Utilisation et entretien d’un

outilélectrique

a ) Ne pas forcer un outil électrique. Utiliser l’outil

électrique approprié à l’application. L’outil

électrique approprié effectuera un meilleur travail,

de façon plus sûre et à la vitesse pour laquelle il

aétéconçu.

b ) Ne pas utiliser un outil électrique dont

l’interrupteur est défectueux. Tout outil électrique

dont l’interrupteur est défectueux est dangereux et doit

êtreréparé.

c ) Débranchez la fiche de la prise électrique et, si

amovible, retirez le bloc‑piles de l’outil avant

d’effectuer tout ajustement, changement et

entreposage de celui‑ci. Ces mesures préventives

réduisent les risques de démarrage accidentel de

l’outilélectrique.

d ) Ranger les outils électriques hors de la portée

des enfants et ne permettre à aucune personne

n’étant pas familière avec un outil électrique ou

La page charge ...

Craftsman CMCM300B Manuel utilisateur

Marque: Craftsman

Modèle: CMCM300B

Catégorie: Outils électroportatifs

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Craftsman CMCM300B User manual
español: Craftsman CMCM300B Manual de usuario

Documents connexes

Craftsman CMCS551BLW Manuel utilisateur

Craftsman CMCM300B Manuel utilisateur

Craftsman CMCM300B Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents