Superior Fireplaces DRL4543 Mode d'emploi

Marque: Superior Fireplaces

Modèle: DRL4543

Catégorie: Cheminées

Taper: Mode d'emploi

P/N 126718-01 Rev. N 04/2020

P126718-01

Ce manuel est disponible en francais, simplement

en faire la demande. Numéro de la pièce 126718-02.

- Do not store or use gasoline or other ﬂammable

vapors and liquids in the vicinity of this or any

other appliance.

- WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use

any phone in your building.

• Leave the building immediately.

• Immediately call your gas supplier from a neigh-

bor’s phone. Follow the gas supplier’s instruc-

tions.

• If you cannot reach your gas supplier, call the

ﬁre department.

- Installation and service must be performed by

a qualiﬁed installer, service agency or the gas

supplier.

WARNING:

FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly could

result in serious injury, death, or property damage.

AVERTISSEMENT:

RISQUED’INDENDIE OU D’EXPLOSION

Le non-respect Des avertissements de sécurité

pourrait d’entraîner des blessures graves, la mort

ou des dommages matériels.

- Ne pas entreposer ni utilizer d’essence ni d’autres

vapeurs ou liquides inﬂammables dans le voisinage

de cet appareil ou de tout autre appareil.

- QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE GAZ:

• Ne pas tenter d’allumer d’appareil.

• Ne touchez à aucan interrupteur. Ne pas vous servir

des téléphones se trouvant dans le bâtiment où

vous trouvez.

• Sortez immédiatement de bâtiment.

• Appelez immédiatement votre fournisseur de

gaz depuis un voisin. Suivez les instructions du

fournisseur.

• Si vous ne pouvez rejoindre le fournisseur de gaz,

appelez le service des incindies.

- L’installation et l’entretien doivent être assurés par

un installateur ou un service d’entretien qualiﬁé

ou par le fournisseur de gaz.

NOTE: DIAGRAMS AND ILLUSTRATIONS THROUGHOUT THE MANUAL ARE NOT TO SCALE.

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for future

reference.

Installateur : Laissez cette notice avec l’appareil.

Consommateur : Conservez cette notice pour

consultation ultérieure.

This appliance may be installed in an aftermarket permanently located, manufactured home (USA only) or

mobile home, where not prohibited by local codes. This appliance is only for use with the type of gas indicated

on the rating plate. This appliance is not convertible for use with other gases, unless a certiﬁed kit is used.

Cet appareil peut installé dans une maison préfabriquée (mobile) déjà installée à demeure, si les réglements

locaux le permettent. Ce appareil doit être utilisé uniquement avec le type de gaz indiqué sure la plaque

signalétique. Cet appareil ne peut être converti à d’autres gaz, sauf si une trousse de conversion est utilsée.

Installation and Operation Instructions

DRL4500 Series Direct-Vent Linear Gas Fireplace

Models

DRL4543TEN

DRL4543TEP

Report No. F11 -026

PFS

USC

SuperiorFireplaces.us.com 126718-01N2

DANGER

HOT GLASS WILL

CAUSE BURNS.

DO NOT TOUCH GLASS

UNTIL COOLED.

NEVER ALLOW CHILDREN

TO TOUCH GLASS.

A barrier designed to reduce the risk of burns from the hot viewing glass is pro-

vided with this appliance and must be installed for the protection of children and

other at-risk individuals.

DANGER

PELIGRO

VITRE CHAUDE

RISQUE DE BRÛLURES.

NE TOUCHEZ PAS UNE VITRE

NON REFROIDIE.

NE LAISSEZ JAMAIS UN ENFANT

DE TOUCHER LA VITRE.

EL VIDRIO CALIENTE

CAUSARÁ QUEMADURAS.

USTED DEBE NUNCA

TOCAR EL VIDRIO CALIENTE.

LOS NIÑOS DEBEN NUNCA

TOCAR EL VIDRIO.

L’écran pare-étincelles fourni avec ce foyer réduit le risque de brûlure en cas de

contact accidentel avec la vitre chaude et doit être installé pour la protection Des

enfants et Des personnes à risques.

Se provee con este aparato una barrera de proteccion (malla), diseñada para reducir

el riesgo de quemaduras por contacto accidental con el vidrio caliente que debe

estar instalada para proteccion de infantes y otros individuos en riesgo.

Vea el volante adjunto para la representación de color adecuado

See attached color ﬂyer for proper color representation

Voir ci-joint tract pour une bonne représentation de la couleur

SAFETY AND YOUR FIREPLACE

SuperiorFireplaces.us.com126718-01N 3

 Aﬁn d’éviter les brûlures

graves ou les blessures,

ne pas retirer l’écran de

protection de la foyer qui

empêche tout contact

direct avec la vitre.

Para evitar quemaduras y lesiones

graves, no quite el protector de malla

o guardia de seguridad que evita el

contacto directo con el vidrio.

Seguridad y su

chimenea

La sécurité et

votre foyer

[FRENCH][ENGLISH]

[SPANISH]

Safety and Your

Fireplace

 To prevent severe burns

and injuries, do Not remove

the barrier on the appliance

which prevents direct

contact with the glass.

All parts of your

IHP ﬁreplace get

EXTREMELY HOT!

Toutes les parties de votre

foyer IHP deviennent

EXTRÊMEMENT CHAUDES !

¡Todas las partes de la

chimenea IHP se ponen

MUY CALIENTES!

 Follow the safety instructions

below and be sure everyone in your

household understands this burn

hazard:

• The surfaces on your fireplace get

EXTREMELY HOT!

• The glass on the front of the

fireplace reaches EXTREMELY HIGH

temperatures and can cause severe

burns if touched.

• Keep children away from an

operating fireplace. Closely

supervise children in any room

where a fireplace is operating to

prevent contact with glass.

• Keep clothing, furniture, gasoline,

and other flammable liquids away

from the fireplace.

• Even after the gas is turned

off, fireplace surfaces remain

extremely hot.

 Be sure to attach the enclosed Safety-

in-Operation Warnings where you

turn on your ﬁreplace, to help remind

everyone of the dangers associated

with high temperatures

(Page 34)

 Read Important Safety Information

(Page 4)

 Suivez les instructions de sécurité

ci-dessous et veillez à ce que tous

les membres de votre famille soient

conscients du danger de brûlure

encouru :

• Les surfaces de votre foyer

deviennent EXTRÊMEMENT CHAUDES

• La vitre située à l'avant du

foyer atteint des températures

EXTRÊMEMENT ÉLEVÉES et peut

causer de graves blessures en cas de

contact.

• Tenez les enfants à l'écart du foyer

lorsqu'il fonctionne. Surveillez

attentivement les enfants dans les

pièces où un foyer est utilisé aﬁn

d'éviter qu'ils ne soient en contact

avec la vitre.

• Tenez tous les vêtements, les

meubles, l'essence et tout autre

liquide inﬂammable à l'écart du foyer.

• Même après fermeture du gaz, les

surfaces du foyer restent extrêmement

chaudes.

 Veillez à coller les Étiquettes de mise

en garde relatives à la sécurité

d'utilisation à l'endroit où vous

utilisez le foyer, pour rappeler à tous

les utilisateurs les dangers liés aux

températures élevées

(Page 34)



Lisez L’information de sûreté

importante (Page 4)

 Siga las instrucciones de seguridad

a continuación y asegúrese de que

todos en su hogar sepan acerca de

este peligro de quemadura:

• ¡Las superﬁcies de la chimenea se

ponen MUY CALIENTES!

• El vidrio delante de la

chimenea alcanza temperaturas

EXTREMADAMENTE ALTAS y puede

causar quemaduras graves si se toca.

• Mantenga a los niños alejados de

la chimenea en funcionamiento.

Supervise en forma cercana a los

niños en cualquier cuarto donde

haya una chimenea funcionando para

impedir el contacto con el vidrio.

• Mantenga la ropa, mobiliario,

gasolina y otros líquidos inﬂamables

alejados de la chimenea.

• Aún después de haber apagado el

gas, las superﬁcies de la chimenea

permanecen extremadamente calientes.

 Asegúrese de colocar las Etiquetas

de advertencia de seguridad de

operación en el lugar donde enciende

la chimenea, para que todos recuerden

los peligros asociados con las altas

temperaturas

(Página 34)



Lea Información importante de

seguridad (página 4).

SuperiorFireplaces.us.com 126718-01N4

SAFETY

WARNING: Improper installation, adjustment,

alteration, service or maintenance can cause injury

or property damage. Refer to this manual for correct

installation and operational procedures. For assis-

tance or additional information consult a qualiﬁed

installer, service agency or the gas supplier.

This appliance is only for use with the type of gas

indicated on the rating plate. This appliance is not

convertible for use with other gases, unless a certi-

ﬁed kit is used.

State of Massachusetts: The installation must be

made by a licensed plumber or gas ﬁtter in the Com-

monwealth of Massachusetts.

WARNING: This product can expose you to

chemicals including Carbon Black, which is known to

the State of California to cause cancer, and Carbon

Monoxide, which is known to the State of California

to cause birth defects or other reproductive harm. For

more information go to www.P65Warnings.ca.gov.

IMPORTANT: Read this owner’s manual carefully and

completely before trying to assemble, operate or

service this ﬁreplace. Improper use of this ﬁreplace

can cause serious injury or death from burns, ﬁre,

explosion, electrical shock and carbon monoxide

poisoning.

DANGER: Carbon monoxide poisoning may lead

to death!

WARNING: Do not slam or strike glass doors.

Damage can result in a hazardous condition.

Young children should be carefully supervised when they are in

the same room as the appliance. Toddlers, young children and

others may be susceptible to accidental burns. A physical barrier

is recommended if there are at-risk individuals in the house.

To restrict access to a ﬁreplace or stove, install an adjustable

safety gate to keep toddlers, young children and other at-risk

individuals out of the room and away from hot surfaces.

This vented gas ﬁreplace is a sealed combustion gas ﬁreplace de-

signed for residential applications. This ﬁreplace must be installed

with INNOVATIVE HEARTH PRODUCTS (IHP) vent pipe components

and terminations.

NOTICE: Decorative product not for use as a heating

appliance.

Thank you for your purchase. We appreciate your business!

Please carefully read and follow all instructions in this manual. Pay special attention to all warnings and safety information.

Following these safety, care, and operation instructions will help ensure many years of dependable and enjoyable service from your

ﬁreplace.

Please read and understand these instructions before installing or operating.

TABLE OF CONTENTS

Safety and Your Fireplace ............................................................... 2

Local Codes ...................................................................................7

Product Identiﬁcation ..................................................................... 7

Product Features ............................................................................8

Requirements for the Commonwealth of Massachusetts ..............8

Pre-installation ...............................................................................9

Location of Termination Cap ........................................................12

Venting Installation ......................................................................13

Fireplace Installation ....................................................................25

Installer - Attaching Safety In Operation Warnings.......................32

Operation ....................................................................................33

Homeowner - Attaching Safety In Operation Warnings................34

Inspecting Burners ....................................................................... 35

Cleaning and Maintenance ...........................................................36

Replacing Light Bulbs ..................................................................36

Gas Control Module System ........................................................37

Remote Control Operation ...........................................................37

Speciﬁcations ...............................................................................39

Wiring Diagram ............................................................................40

Troubleshooting ...........................................................................41

Parts ............................................................................................43

Replacement Parts .......................................................................47

Technical Service .........................................................................47

Service Hints ................................................................................ 47

Accessories .................................................................................. 47

Warranty ......................................................................................49

WARNING

Never connect this appliance to private (non-utility) gas

wells. This gas is commonly known as wellhead gas

and does not have odorants and may have impurities,

and variations in BTU content. The use of well-head gas

will void the manufacturer’s warranty to this appliance.

SuperiorFireplaces.us.com126718-01N 5

Important Safety Informa-

tion

1. WARNING: Do not operate appliance

with the glass front removed, cracked,

or broken.

2. Do not use this appliance if any part

has been under water. Immediately

call a qualiﬁed service technician to

inspect the appliance and to replace

any part of the control system and

any gas control which has been under

water.

3. Due to high temperatures, the appli-

ance should be located out of trafﬁc

and away from furniture and draperies.

4. Children and adults should be alerted

to the hazards of high surface tem-

perature and should stay away to avoid

burns or clothing ignition.

5. Clothing or other ﬂammable material

should not be placed on or near the

appliance.

6. Young children should be carefully

supervised when they are in the same

room as the appliance. Toddlers,

young children, and others may be sus-

ceptible to accidental contact burns.

A physical barrier is recommended

if there are at-risk individuals in the

house. To restrict access to a ﬁreplace

or stove, install an adjustable safety

gate to keep toddlers, young children,

and other at-risk individuals out of the

room and away from hot surfaces.

7. Any safety screen, guard or barrier

removed for servicing an appliance

must be replaced prior to operating

the appliance.

8. Installation and repair should be done

by a qualiﬁed service person. The

appliance should be inspected before

use and at least annually by a profes-

sional service person. More frequent

cleaning may be required due to

excessive lint from carpeting, bedding

material, et cetera. It is imperative

that control compartments, burners,

and circulating air passageways of the

appliance be kept clean. See mainte-

nance instructions on Page 36.

L’information de sûreté

importante

1. AVERTISSEMENT. Ne pas utiliser l’appareil

si le panneau frontal en verre n’est pas en

place, est craqué ou brisé.

2. Ne pas se servir de cet appareil s’il a été

plongé dans l’eau, même partiellement.

Faire inspecter l'appareil par un technicien

qualiﬁé et remplacer toute partie du systéme

de contrôle et toute commande qui ont été

plongées dans l'eau.

3. En raison des températures élevées,

l’appareil devrait être installé dans un

endroit où il y a peu de circulation et loin

du mobilier et des tentures.

4. Les enfants et les adultes devraient être

informés des dangers que posent les tem-

pératures de surface élevées et se tenir à

distance aﬁn d’éviter des brûlures ou que

leurs vêtements ne s’enﬂamment.

5. On ne devrait pas placer de vêtements

ni d’autres matières inflammables sur

l’appareil ni à proximité.

6. Les jeunes enfants devraient être surveillés

étroitement lorsqu’ils se trouvent dans la

même pièce que l’appareil. Les tout petits,

les jeunes enfants ou les adultes peuvent

subir des brûlures s’ils viennent en contact

avec la surface chaude. Il est recommandé

d’installer une barrière physique si des

personnes à risques habitent la maison.

Pour empêcher l’accès à un foyer ou à un

poêle, installez une barrière de sécurité

; cette mesure empêchera les tout petits,

les jeunes enfants et toute autre personne

à risque d’avoir accès à la pièce et aux

surfaces chaudes.

7. Tout écran ou protecteur retiré pour per-

mettre l’entretien de l’appareil doit être

remis en place avant de mettre l’appareil

en marche.

8. L’installation et la réparation devrait être

conﬁées à un technicien qualiﬁé. L’appareil

devrait faire l’objet d’une inspection par un

technicien professionnel avant d’être utilisé

et au moins une fois l’an par la suite. Des

nettoyages plus fréquents peuvent être

nécessaires si les tapis, la literie, et cetera

produisent une quantité importante de pous

sière. Il est essentiel que les compartiments

abritant les commandes, les brûleurs et les

conduits de circulation d’air de l’appareil

soient tenus propres. Voyez les instructions

d’entretien à la Page 36.

Información importante de

seguridad

1. ADVERTENCIA: No opere el artefacto con el

frente de vidrio quitado, agrietado o roto.

2. No use este artefacto si alguna de sus partes

ha estado bajo agua. Llame de inmediato

a un técnico de servicio caliﬁcado para

que inspeccione el artefacto y reemplace

cualquier parte del sistema de control y

cualquier control de gas que haya estado

bajo agua.

3. Debido a las altas temperaturas, el artefacto

debe situarse fuera de las áreas de tráﬁco y

lejos del mobiliario y cortinas.

4. Se debe alertar a los niños y adultos sobre

los peligros de las altas temperaturas en la

superﬁcie y que se mantengan alejados para

evitar quemaduras o ignición de la ropa.

5. No debe colocarse ropa u otros materiales

inﬂamables sobre y cerca del artefacto.

6. Se debe supervisar de cerca a los niños

cuando estén en el mismo cuarto que el

artefacto. Los niños pequeños, los jóvenes

y otras personas pueden ser susceptibles

a quemaduras por contacto accidental. Se

recomienda instalar una barrera física si hay

personas en riesgo en la casa. Para restringir

el acceso a una chimenea o estufa, instale

una puerta de seguridad ajustable para

mantener a los niños pequeños, jóvenes y

otras personas en riesgo fuera del cuarto y

lejos de las superﬁcies calientes.

7. Cualquier malla o resguardo de seguridad

quitado para dar servicio a un artefacto, debe

reinstalarse antes de operar el artefacto.

8. Una persona de servicio competente debe

realizar la instalación y reparación. Una

persona de servicio profesional debe

inspeccionar el artefacto antes de usar al

menos una vez por año. Se puede requerir

limpieza más frecuente debido a la pelusa

excesiva del alfombrado, del material de

cobijas, etc. Es imprescindible mantener

limpios los compartimientos de control, los

quemadores y los pasajes de circulación del

aire del artefacto. Ver las instrucciones de

mantenimiento en la página 36.

IMPORTANT SAFETY INFORMATION

SuperiorFireplaces.us.com 126718-01N6

This ﬁreplace must be installed by a qualiﬁed (certiﬁed or licensed)

service person. It brings in fresh air for combustion through the outer

pipe and combustion gases are exhausted through the inner pipe. If

the glass door assembly and venting pipe are not properly seated,

connected and sealed, carbon monoxide leakage (spillage) can occur.

Carbon Monoxide Poisoning: Early signs of carbon monoxide poison-

ing resemble the ﬂu, with headaches, dizziness or nausea. If you have

these signs, the ﬁreplace may not be working properly. Get fresh air

at once! Have ﬁreplace serviced. Some people are more affected by

carbon monoxide than others. These include pregnant women, people

with heart or lung disease or anemia, those under the inﬂuence of

alcohol and those at high altitudes.

Natural and Propane/LP Gas: Natural and propane/LP gas are odor-

less. An odor-making agent is added to the gas. The odor helps you

detect a gas leak. However, the odor added to the gas can fade. Gas

may be present even though no odor exists.

Make certain you read and understand all warnings. Keep this manual

for reference. It is your guide to safe and proper operation of this

ﬁreplace.

WARNING: Any change to this ﬁreplace or its con-

trols can be dangerous. Do not modify this ﬁreplace

under any circumstances. Any parts removed for ser-

vicing must be replaced prior to operating ﬁreplace.

WARNING: Do not use a blower insert, heat ex-

changer insert or other accessory not approved for use

with this ﬁreplace.

WARNING: This appliance is only for use with

the type of gas indicated on the rating plate. This

appliance is not convertible for use with other gases

unless a certiﬁed kit is used.

WARNING: Do not allow fans to blow directly into

the ﬁreplace. Avoid any drafts that alter burner ﬂame

patterns.

Due to high temperatures, the appliance should be

located out of trafﬁc and away from furniture and

draperies.

Clothing or other ﬂammable material should not be

placed on or near the appliance.

Do not use this ﬁreplace to cook food or burn paper

or other ﬂammable material.

Any safety screen, guard, or barrier removed for

servicing an appliance must be replaced prior to

operating the appliance.

SAFETY Continued

Installation and repair should be done by a qualiﬁed

service person. The appliance should be inspected

before use and at least annually by a professional

service person. More frequent cleaning may be re-

quired due to excessive lint from carpeting, bedding

material, etcetera. It is imperative that control com-

partments, burners, and circulating air passageways

of the appliance be kept clean.

Children and adults should be alerted to the hazards

of high surface temperature and should stay away

to avoid burns or clothing ignition.

A barrier designed to reduce the risk of burns from

the hot viewing glass is provided with this appliance

and shall be installed for the protection of children

and other at-risk individuals.

If the barrier becomes damaged, the barrier shall

be replaced with the manufacturer's barrier for this

appliance.

Keep the area around your ﬁreplace clear of combus-

tible materials, gasoline and other ﬂammable vapor

or liquids. Do not run ﬁreplace where these are used

or stored.

1. For propane/LP ﬁreplace, do not place propane/LP supply tank(s)

inside any structure. Locate propane/LP supply tank(s) outdoors.

To prevent performance problems, do not use propane/LP fuel

tank of less than 100 lb. capacity.

2. If you smell gas

• shut off gas supply

• do not try to light any appliance

• do not touch any electrical switch; do not use any phone in your

building

• immediately call your gas supplier from a neighbor’s phone.

Follow the gas supplier's instructions

• if you cannot reach your gas supplier, call the ﬁre department.

3. Never install the ﬁreplace

• in a recreational vehicle

• in windy or drafty areas where curtains or other combustible (ﬂam-

mable) objects can make contact with the ﬁreplace front

• in high trafﬁc areas

4. Turn ﬁreplace off and let cool before servicing, installing or

repairing. Only a qualiﬁed service person should install, service

or repair this ﬁreplace. Have ﬁreplace inspected annually by a

qualiﬁed service person.

5. You must keep control compartments, burners and circulating

air passages clean. More frequent cleaning may be needed due

to excessive lint and dust from carpeting, bedding material, etc.

Turn off the gas valve and pilot light before cleaning ﬁreplace.

SuperiorFireplaces.us.com126718-01N 7

Glass Door

Pebble

Pan

Flue Collar

Nailing

Flange

Access Door

Barrier J7457

Top Spacers

SAFETY Continued

6. Have venting system inspected annually by a qualiﬁed service

person. If needed, have venting system cleaned or repaired. See

Cleaning and Maintenance, Page 36.

7. Do not use any solid fuels (wood, coal, paper, cardboard, etc.) in

this ﬁreplace. Use only the gas type indicated on ﬁreplace name-

plate.

8. This appliance, when installed, must be electrically grounded in

accordance with local codes or, in the absence of local codes, with

Listing: This ﬁreplace complies with the National Safety Standards

and is listed and tested by PFS TECO to ANSI Z21.50/CSA 2.22

standard as vented gas ﬁreplace and applicable sections of Z21.97

standard for outdoor decorative gas appliance (When installed as a

see-thru unit using outdoor kit model LDSTO).

These appliances comply with CSA P.4.1-2015 “Testing Method for

Measuring Annual Fireplace Efﬁciency. P4 (EnerGuide) is a measure-

ment of the Canadian Ofﬁce of Energy Efﬁciency.

PRODUCT IDENTIFICATION

Figure 1 - DRL4543 Linear Fireplace

the National Electrical Code, ANSI/NFPA 70 or Canadian Electrical

Code, CSA C22.1.

9. Do not use ﬁreplace if any part has been exposed to or under

water. Immediately call a qualiﬁed service person to arrange for

replacement of the unit.

10. Do not operate ﬁreplace with glass door removed, cracked or

broken.

11. Provide adequate clearances around air openings.

LOCAL CODES

Install and use ﬁreplace with care. Follow all local codes. In the ab-

sence to local codes, use the current National Fuel Gas Code ANSI

Z223.1/NFPA 54* (USA) or the current CSA-B149.1 Installation Code

(Canada).

*Available from:

American National Standards Institute, Inc.

25 West 43rd Street, 4th ﬂoor

New York, NY 10036

National Fire Protection Association, Inc.

1 Batterymarch Park

Quincy, MA 02169-7471

Based on CSA P. 4.1-2015

SuperiorFireplaces.us.com 126718-01N8

COMMONWEALTH OF MASSACHUSETTS REQUIREMENTS

These appliances are approved for installation in the US state of

Massachusetts if the following additional requirements are met:

• Install this appliance in accordance with Massachusetts Rules

and Regulations 248 C.M.R. Sections 4.00 through 8.00.

• Installation and repair must be done by a plumber or gas ﬁtter

licensed in the Commonwealth of Massachusetts.

• The ﬂexible gas line connector used shall not exceed 36 inches

(92 centimeters) in length.

• The individual manual shut-off must be a T-handle type valve.

REQUIREMENTS FOR THE COMMONWEALTH OF MASSACHUSETTS

Massachusetts Horizontal Vent Requirements

In the Commonwealth of Massachusetts, horizontal terminations

installed less than seven (7) feet above the ﬁnished grade must

comply with the following additional requirements:

• A hard wired carbon monoxide detector with an alarm and

battery back-up must be installed on the ﬂoor level where

the gas ﬁreplace is installed. The carbon monoxide detector

must comply with NFPA 720, be ANSI/UL 2034 listed and be

ISA certiﬁed.

• A metal or plastic identiﬁcation plate must be permanently

mounted to the exterior of the building at a minimum height

of eight (8) feet above grade and be directly in line with the

horizontal termination. The sign must read, in print size no less

than one-half (1/2) inch in size, GAS VENT DIRECTLY BELOW.

KEEP CLEAR OF ALL OBSTRUCTIONS.

PRODUCT FEATURES

These are a few facts that can help you understand and enjoy your

direct-vent ﬁreplace:

• The venting system may be routed to the outside of your home in

several ways. It may vent through the roof (vertical) or it may vent

to an outside/exterior wall (horizontal). The vent pipe installation is

very important to allow for proper operation. You must follow the

venting instructions very carefully for either vertical or horizontal

applications.

• This ﬁreplace may be installed in any room of your house provided

all local codes and these installation instructions are followed.

• Each time you turn on your ﬁreplace, you may notice some amount

of condensation on the inside of the ﬁreplace glass. This is normal

and will disappear after 10-20 minutes of operation.

• Your direct-vent gas ﬁreplace system (ﬁreplace and venting) is a

balanced and sealed gas operating unit. It requires approximately

10-20 minutes of operating time before the ﬂame pattern stabilizes.

SuperiorFireplaces.us.com126718-01N 9

PRE-INSTALLATION

LOCATION AND SPACE REQUIREMENTS

Determine the safest and most efﬁcient location for your direct-vent

ﬁreplace. Make sure that rafters and wall studs are not in the way

of the venting system. Choose a location where the heat output is

not affected by drafts, air conditioning ducts, windows or doors. Be

aware of all restrictions and precautions before deciding the exact

location for your ﬁreplace and termination cap.

When deciding the location of your ﬁreplace, follow these rules:

• Do not connect this ﬁreplace venting to a chimney ﬂue serving a

separate solid-fuel burning ﬁreplace or appliance.

• Due to high temperatures, do not locate this ﬁreplace in high trafﬁc

areas, windy or drafty areas or near furniture or draperies.

• Proper clearances must be maintained.

• If your ﬁreplace is to be installed directly on carpeting, vinyl tile or any

combustible material other than wood, it must be installed on a metal

or wood panel extending the full width and depth of the ﬁreplace (see

Figure 6, Page 11).

• If standoff spacers are attached to your ﬁreplace, these spacers

can be placed directly against wall or framing material. See framing

details, Page 10.

• When locating termination cap, it is important to observe the

minimum clearances shown in Figure 7, Page 12.

• Do not recess termination cap into a wall or siding.

• You may paint the termination cap with 450º F (232º C) heat-

resistant paint to coordinate with the exterior ﬁnish.

• There must not be any obstruction such as bushes, garden sheds,

fences, decks or utility buildings within 24" from the front of the

termination cap and the front of outside air vent.

• Do not locate termination cap and outside air vent where excessive

snow or ice build up may occur. Be sure to clear vent termination

area after snow falls to prevent accidental blockage of venting

system. When using snow blowers, do not direct snow towards

vent termination area.

CLEARANCES

Minimum clearances to combustibles for the ﬁreplace are as follows:

*Back and sides 1" (26 mm)

Perpendicular walls 8" (204 mm)

Floor (From bottom of Fireplace) 0" (0 mm)

Ceiling (From bottom of Fireplace) 63" (1601 mm)

Top of Enclosure

(From bottom of Fireplace) 63" (1601 mm)

Top of Standoffs 0" (0 mm)

Vent 1" (26 mm)

(See venting instructions for speciﬁc venting clearances.)

* For back and sides of ﬁreplace, do not pack with insulation or other

materials.

Hearth Extension

A hearth extension is not required with this ﬁreplace. Any hearth

extension used is for appearance only and does not have to conform

to standard hearth extension installation requirements.

NOTICE: This ﬁreplace is intended for use as supple-

mental heat. Use this ﬁreplace along with your primary

heating system. Do not install this ﬁreplace as your

primary heat source. If you have a central heating

system, you may run system’s circulating blower

while using ﬁreplace. This will help circulate the heat

throughout the house.

FRAMING AND FINISHING

Choose framing application accordingly. Figure 2, Page 10 shows

typical one sided framing. Figure 3, Page 10 shows framing for

see-thru installation. NOTE: Kits F2312 and F2313 are required

for see-thru application (See upgrading DRL4543 to indoor/outdoor

see-thru application, Page 31).

All minimum clearances must be met. Vent pipe needs to maintain

1" clearance. Steel framing may be necessary or wood studs may be

notched. Concrete board is provided for facing around the ﬁreplace

as shown in Figure 4, Page 10.

If you are using a separate combustible mantel piece, refer to Figure

5, Page 10 for proper installation height. You can install noncom-

bustible mantels at any height above the ﬁreplace.

NOTE: To avoid heat-related ﬁnish damage, we recommend the

use of high temperature paint (rated 175° F or higher) on the

underside of the mantel.

SuperiorFireplaces.us.com 126718-01N10

PRE-INSTALLATION Continued

Figure 2 - Framing Clearances for One Sided Application

Figure 3 - Framing Clearances for See-Thru Application

Figure 5 - Clearances for Combustible Mantels

Figure 4 - Installing Concrete Board

Concrete

Board

Wall

TOP VIEW

SAFE

ZONE

Perpendicular

Wall

Combustible

Material May

Be Used

33°

(204 mm)

to Face Opening

(127 mm)

(1353 mm)

*53

(1353 mm)

38"

(965 mm)

38"

(965 mm)

STUDS MOUNTED (FLAT)

INSIDE OF NAILING FLANGE

(387 mm)

MOUNTED INSIDE OF

NAILING FLANGE

(FLAT)

FOR ONE SIDED

APPLICATION, STUDS

ARE NOT MOUNTED

TO THE REAR

OF NAILING FLANGES

(445 mm)

*Please refer to overall ﬁreplace width (Figure 6, Page 11) before

rough framing construction.

Ref.

Mantel

Depth Ref.

Mantel from Top

of Opening

1 12" A 24" (610 mm)

2 9" B 21" (554 mm)

3 6" C 18" (458 mm)

4 4" D 16" (407 mm)

5 2" E 14" (356 mm)

SuperiorFireplaces.us.com126718-01N 11

PRE-INSTALLATION Continued

(54 mm)

(16 mm)

(298 mm)

(419 mm)

(210 mm)

(759 mm)

" (89 mm)

(416 mm)

(181 mm)

(48 mm)

(210 mm)

" (105 mm)

(1121 mm)

(1400 mm)

47"

(1194 mm)

(25 mm)

52"

(1321 mm)

(445 mm)

(206 mm)

(210 mm)

(1114 mm)

Figure 6 - DRL4543 Fireplace Series Dimensions

SuperiorFireplaces.us.com 126718-01N12

LOCATION OF TERMINATION CAP

Figure 7 - Minimum Clearances for Termination Cap

Fixed

Closed

Openable

Fixed

Closed

TERMINATION CAP

AIR SUPPLY INLET

GAS METER RESTRICTED AREA

(TERMINATION PROHIBITED)

A = clearance above grade, veranda, porch, deck, or

balcony [*12" (30.5 cm) minimum]

B = clearance to window or door that may be opened

[6" (15 cm) min. for 10,000 Btu or less; 9" (23 cm) in US

if between 10,000 and 50,000, 12" (30 cm) in Canada

if between 10,000 and 100,000; 12" (30 cm) in US if

greater than 50,000, 36" (91 cm) in Canada if greater

than 100,000]

C = clearance to permanently closed window

[minimum 12" (30.5 cm) recommended to prevent

condensation on window]

D = vertical clearance to ventilated soffit located above the

terminal within a horizontal distance of 24" (61 cm) from

the center-line of the terminal [18" (45.7 cm) minimum]

E = clearance to unventilated soffit [12" (30.5 cm) minimum]

F = clearance to outside corner (see below)

G = clearance to inside corner (see below)

H = *not to be installed above a meter/regulator assembly

within 36" (91.4 cm) horizontally from the center line

of the regulator

I = clearance to service regulator vent outlet [*72" (182.9 cm)

minimum]

J = clearance to non-mechanical air supply inlet to building

or the combustion air inlet to any other fireplace

[6" (15 cm) min. for 10,000 Btu or less; 9" (23 cm) in US

if between 10,000 and 50,000, 12" (30 cm) in Canada

if between 10,000 and 100,000; 12" (30 cm) in US if

greater than 50,000, 36" (91 cm) in Canada if greater

than 100,000]

K = clearance to a mechanical air supply inlet [*In Canada,

6 ft. (1.83m) minimum; In US 3 ft. (91 cm) above if within

10 ft. (3 m) horizontally]

L = † clearance above paved side-walk or a paved driveway

located on public property [*84" (213.3 cm) minimum]

M = clearance under veranda, porch, deck

[*12" (30.5 cm) minimum ‡]

N = clearance above a roof shall extend a minimum of

24" (61 cm) above the highest point when it passes

through the roof surface and any other obstruction within

a horizontal distance of 18" (45.7 cm)

† vent shall not terminate directly above a side-walk or paved driveway which is located between two

single family dwellings and serves both dwellings*

‡ only permitted if veranda, porch, deck or balconey is fully open on a minimum of 2 sides beneath the floor*

* as specified in CAN/CGA B149.1 Installation Codes (1991) for Canada and U.S.A.

Note: Local codes or regulations may require different clearances

A = 6" (15.2 cm)

Inside Corner

B = 6" (15.2 cm)

C = Maximum depth of 48" (121.9 cm)

for recessed location

D = Minimum width for back wall of

recessed location -

Combustible - 38" (965 mm)

Noncombustible - 24" (61 cm)

E = Clearance from corner in

recessed location-

Combustible - 6" (15.2 cm)

Noncombustible - 2" (5.1 cm)

Outside Corner Recessed Location

G = 12" (30.5 cm) minimum clearance

Balcony with No Side Wall

Combustible &

Noncombustible

H = 24" (61 cm)

J = 20" (50.8 cm)

Balcony with Perpendicular Side Wall

Termination Clearances for Buildings with Combustible and Noncombustible Exteriors

Openable

SuperiorFireplaces.us.com126718-01N 13

VENTING INSTALLATION

NOTICE: Read these instructions completely before

attempting installation.

These models are tested and approved for use with an IHP (direct-

vent) pipe components and terminations.

The venting system must terminate on the outside of the structure and

can not be attached to a chimney or ﬂue system serving a separate

solid fuel or gas burning appliance. A direct-vent appliance must

have its own venting system. DO NOT common vent this appliance.

These models are approved to be vented either horizontally through

an outside wall or vertically through a roof or chase enclosure using

the following guidelines:

• When venting system terminates horizontally on an outside wall,

you may install a standoff if the termination cap is to be installed

directly on a combustible ﬁnish such as vinyl, wood, stucco, etc.

• Never run the vent downward as this may cause excessive tem-

peratures which could cause a ﬁre.

• Vent pipe air space clearances to combustibles are 1" on all sides

except on the horizontal sections, which requires 2" clearance

from the top of the pipe. Where the termination cap penetrates a

combustible wall, 1" air space clearance is required.

• Have ﬁreplace and selected vent components on hand to help

determine the exact measurements when elbowing or offsetting.

Always use wall ﬁrestops when penetrating walls and ﬁrestops

when penetrating ceilings or attic spaces.

• For installation of ﬁreplace at elevations of 4000 feet or greater,

pay special attention to venting requirement recommendations.

WARNING: Read all instructions completely and

thoroughly before attempting installation. Failure to

do so could result in serious injury, property damage

or loss of life.

NOTICE: Failure to follow these instructions will void the

warranty.

NOTICE: Do not seal termination cap to vent pipe. Cap

must be removable for vent inspection and mainte-

nance.

WARNING: This gas ﬁreplace and vent assembly

must be vented directly to the outside. The venting

system must NEVER be attached to a chimney serving

a separate solid fuel burning appliance. Each direct-

vent gas appliance must use a separate vent system.

Do not use common vent systems.

WARNING: Vent pipe air space clearances to com-

bustibles are 1" on all sides except on the horizontal

sections, which require 2" clearances from the top

of the pipe. Where the termination cap penetrates a

combustible wall, 1" air space clearance is required.

INSTALLATION PRECAUTIONS

• Wear gloves and safety glasses for protection

• Use extreme caution when using ladders or when on roof tops

• Be aware of electrical wiring locations in walls and ceilings

The following actions will void the warranty on your venting system:

• Installation of any damaged venting component

• Unauthorized modiﬁcation of the venting system (Do not cut or alter

vent components)

• Installation of any component part not manufactured or approved

by IHP

• Installation other than as instructed by these instructions

SuperiorFireplaces.us.com 126718-01N14

VENTING INSTALLATION Continued

INSTALLATION PLANNING

There are two basic types of direct-vent installation:

• Horizontal Termination

• Vertical Termination

Installing the Horizontal Termination Vent System

These instructions should be used as a guideline and do not supersede local codes in any way. Install venting according to local codes,

these instructions, the current National Fuel Gas Code (ANSI-Z223.1) in the USA or the current standards of CAN/CGA-B149.1 in Canada.

Ensure clearances are in accordance with local installation codes and the requirements of the gas supplier.

Horizontal vent systems terminate through an outside wall. Building Codes limit or prohibit terminating in speciﬁc areas (Figure 7, Page 12).

1. Analyze the vent route and determine the number of vent

sections and elbows required—Plan the venting so that a

joint does not occur in the ceiling or roof joists. Maintain

the minimum clearances for combustibles (Page 9).

2. Frame the exterior wall opening—Locate the center of the

vent outlet on the exterior wall. Cut and/ or frame an open-

ing, 10 1/2 x 12 1/8” (267 x 308 mm) inside dimensions,

about this center.

3. Frame the ceiling opening—If the vertical route is to pen-

etrate a ceiling, use plumb line to locate the center above

the fireplace. Cut and/or frame an opening, 10 1/2 x 10

1/2” (267 x 267 mm) inside dimensions, about this center

(Figure 17, Page 19).

4. Attach the vent components to the fireplace—See Con-

necting the vent pipe on Page 17.

5. Attach the vent components to each other—See Connecting

the vent pipe on Page 17.

6. Install the firestop/spacer at the ceiling—When using Rigid

Pipe, use SV4.5VF firestop/spacer at ceiling joists. If there

is living space above the ceiling level, the firestop/spacer

must be installed on the bottom side of the ceiling.

1. If attic space is above the ceiling, the firestop/spacer must

be installed on the top side of the joist. Route the vent sec-

tions through the framed opening and secure the firestop/

spacer with 8d nails or other appropriate fasteners at each

corner. Maintain 1” (26 mm) clearance to combustibles,

framing members, and attic or ceiling insulation when run-

ning vertical chimney sections.

2. Support fireplace vent outlet with field provided support

straps (Plumber’s tape)—Attach the straps to the vent pipe

and secure to the framing members with nails or screws

(Figure 8).

3. Change vent direction—At transition from or to a horizon-

tal/inclined run, install SV4.5E45 or SV4.5E90 elbows in

the same manner as the straight vent sections. The elbows

feature a twist section to allow them to be routed about

the center axis of their initial collar section to align with

the required direction of the next vent run element. Twist

elbow sections in a clockwise direction only so as to avoid

the possibility of unlocking any of the previously connected

vent sections (Figure 13, Page 17).

Figure 8 - Typical Horizontal Vent Installation

ertical

Rise

SV4.5E90

Elbow

Horizontal / Inclined Run

Termination

Firestop/Spacer

SV4.5L6/12/24/36/48

Vent Sections

Support bracket spacing

every 5 ft (1.52 m)

Vertical Vent

Support

Brackets

Building

Support

Framing

Ceiling

Fireplace

Exterior

Wall

Exterior

Wall

Termination

Vertical

Rise

SV4.5E90

Elbow

Horizontal / Inclined Run

SV4.5HTSS

Termination

Shown

*Ceiling

Firestop/Spacer

(SV4.5VF)

SV4.5L6/12/24/36/48

Vent Sections

Support Bracket Spacing

Every 5 ft (1.52 m)

Support

Brackets

Building

Support

Framing

Ceiling

Fireplace

Exterior

Wall

Exterior

Wall

TYPICAL HORIZONTAL VENT INSTALLATION

Firestop/Spacer

SV4.5HTSS

Termination

Shown

Fireplace

*When using Secure Flex use

Firestop/Spacer (SF4.5VF)

Note: Adaptor SV4.5RCH or

SV4.5RCHA must be used to

attach the termination to the

venting system. See Steps J

and K.

Vertical

Rise

SV4.5E90

Elbow

Horizontal / Inclined Run

SV4.5HTSS

Termination

Shown

*Ceiling

Firestop/Spacer

(SV4.5VF)

SV4.5L6/12/24/36/48

Vent Sections

Support Bracket Spacing

Every 5 ft (1.52 m)

Support

Brackets

Building

Support

Framing

Ceiling

Fireplace

Exterior

Wall

Exterior

Wall

TYPICAL HORIZONTAL VENT INSTALLATION

Firestop/Spacer

SV4.5HTSS

Termination

Shown

Fireplace

*When using Secure Flex use

Firestop/Spacer (SF4.5VF)

Note: Adaptor SV4.5RCH or

SV4.5RCHA must be used to

attach the termination to the

venting system. See Steps J

and K.

SuperiorFireplaces.us.com126718-01N 15

VENTING INSTALLATION Continued

1. Continue installation of horizontal/inclined sections—

Continue with the installation of the straight vent sections

in horizontal/inclined run. Install support straps every

5 ft. (1.52 m) along horizontal/inclined vent runs using

conventional plumber’s tape (Figure 8, Page 14). Maintain

the horizontal/inclined run in a straight (no dips), slightly

elevated plane. The recommended incline is approximately

1/4” per 1 ft (20 mm per 1 m) horizontal, in a direction

away from the fireplace. Smaller rise per foot run ratios are

acceptable all the way to at or near level. Use a carpenter’s

level to measure from a constant surface and adjust the sup-

port straps as necessary. Maintain the required clearances

to combustibles (Page 9).

2. Assemble the vent run to the exterior wall—If not previ-

ously measured, locate the center of the vent at the exterior

wall. Prepare the opening. Assemble the vent system until

the terminus of the last section is within 7” (178 mm) to

11-1/4” (286 mm) inboard of the exterior surface to which

the SV4.5 HT termination is to be attached (Figure 9). If the

terminus of the last section is not within this distance, use

the telescopic vent section SV4.5LA, as the last vent section.

Table 1, Page 16 lists the additional venting components

needed (in addition to the termination and adaptor) for a

range of wall thicknesses.

3. Attach the termination adaptor—Attach the adaptor

(SV4.5RCH, provided with the termination) to the vent sec-

tion or telescoping vent section, elbow or fireplace collar

(Figure 9).

4. Install the firestop/spacer at the exterior wall—When us-

ing the square termination, install SV4.5HF Firestop/Spacer

over the opening at the exterior side of the framing, long

side up, with the 3” spacer clearance at the top (Figure 9)

and nail into place.

NOTE: The firestop/spacer may also be installed over the

opening at the interior side of the framing.

1. Install the termination (SV4.5HTSS)—From outside the

exterior wall, slide the collars of the termination onto the

adaptor (the outer over the outer and the inner inside the

inner) until the termination seats against the exterior wall

surface to which it will be attached. Orient the housing of

the termination with the arrow pointed upwards. Secure the

termination to the exterior wall. The horizontal termination

must not be recessed into the exterior wall or siding by more

than the 1-1/4” (32 mm) (Figure 10, Page 16).

NOTE: The vent termination is hot while in operation and for

a period of time following the use of the fireplace. To pre-

vent contact with hot surfaces, use a horizontal termination

guard; available for purchase at your local dealer.

The horizontal terminations have been designed to perform

in a wide range of weather conditions. Our terminations meet

or exceed industry standards.

When selecting the locations of your horizontal terminations,

do not place the termination where water from eaves and ad-

joining rooflines may create a heavy flow of cascading water

onto the termination cap. If the cap must be placed where the

possibility of cascading water exists, it is the responsibility of

the builder to direct the water away from the termination cap

by using gutters or other means.

Take care to carefully follow the installation instructions for

the termination, including the use of silicone caulking where

required.

Figure 9 - Installing the Horizontal Termination

Termination

ermination

10 1/2”

(267mm)

7”

(178)

5 1/8”

(130 mm)

12 1/8”

(308 mm)

Note: Centerline of Vent Piping is

NOT the Same as the Centerline of

the Framed Opening.

6 to 48” Vent Section,

Telescopic vent section,

Elbow or Appliance Collar

53” (1346 mm) Min.

Plus 1/4”(6 mm)

Rise per Foot

Base of Appliance

3”

(76 mm)

1”

(26 mm)

Adaptor

SV4.5RCH

To help minimize water

infiltration it is recommended that

the Firestop/Spacer (SV4.5HF)

be installed on the exterior

side of the wall.

*Firestop/Spacer (SV4.5HF) shown

on the exterior side of the wall. It

may also be installed on the

interior side.

SV4.5 HTSS

Termination

Shown.

10-1/2"

(267 mm)

(178)

5-1/8"

(130 mm)

12-1/8"

(308 mm)

NOTE: Centerline of Vent

Piping is NOT the Same as

the Centerline of the

Framed Opening.

6” to 48” Vent Section,

Telescopic vent section,

Elbow or Appliance Collar

Base of Appliance

(77 mm)

(26 mm)

Adaptor

SV4.5RCH or

SV4.5RCHA

NOTE: When using Secure Flex

use Firestop/Spacer SF4.5HF

See Fireplace

Installation Instructions

For Min. Distance to

Base of Appliance.

SuperiorFireplaces.us.com 126718-01N16

VENTING INSTALLATION Continued

NOTE: See Table 1 for wall thickness ranges when using an approved

IHP termination kit.

Vent Components Required Exterior Wall Thickness

Termination Kit Only 6 to 9-1/4” (152–235 mm)

Termination Kit and 6” Vent Section

(SV4.5L6)

10-3/4 to14” (273–356 mm)

Termination Kit and 12” Vent Section

(SV4.5L12)

16-3/4 to 20” (426–508 mm)

Termination Kit and Telescopic Section

(SV4.5LA) and 6” vent section (SV4.5L6)

11-3/4 to 20” (299–508 mm)

Table 1: Venting Components Required for Various Exterior Wall

Thicknesses, when using Typical Termination Kits

Model Effective Length

SV4.5L6 4-1/2” (115 mm)

SV4.5L12 10-1/2” (267 mm)

SV4.5L24 22-1/2” (572 mm)

SV4.5L36 34-1/2” (877 mm)

SV4.5L48 46-1/2” (1181 mm)

Table 2: Effective Vent Length

Figure 10 - Venting Connection and Exterior Wall Recessing of the Horizontal Square Termination (SV4.5HTSS)

** For thicknesses greater than

9-1/4” (235 mm) see Table 21.

Siding

Stucco

1-1/4” Maximum Recess of

the Square Termination into

Exterior Finishing Material

Exterior Surface of

Framing

6” to 9-1/4”

(152 to 235 mm)**

Exterior Surface of Siding

Interior Surface of

Finished Wall

Maximum wall thickness

9-1/4” (235 mm)**

Maximum Extent of

Vent Run Sections

Relative to Exterior

Surface of Framing

Last Vent Section. Use

Telescopic Vent

Section (SV4.5LA), If

Necessary

Adaptor

SV4.5RCH

*Use silicone caulking to

seal the top and sides of

the termination, up to the

underlayment, stucco, or

masonry wall surface.

*Caulk

Siding

Stucco

Caulk*

SuperiorFireplaces.us.com126718-01N 17

VENTING INSTALLATION Continued

Connecting the vent pipe

Direct-vent system components are unitized concentric pipe

components featuring positive twist lock connections (Figure 11

and Figure 12). All of the fireplaces covered in this document are

fitted with collars having locking inclined channels. The dimpled

end of the vent components fit over the fireplace/vent collar to

create the positive twist lock connection.

1. Align the dimpled end over the collar, adjusting the radial

alignment until the four (4) locking dimples are aligned

with the inlet of the four (4) inclined channels on the collar

(Figure 11).

1. Push the vent component against the collar until it fully

engages, then twist the component clockwise, running the

dimples down and along the incline channels until they seat

at the end of the channels.

NOTE: The unitized design of the Rigid Pipe components will

engage and seal both the inner and outer vent pipe.

2. If desired, a #6 x 1/2” screw can be used at the joint, but

is not required as the pipe will securely lock when twisted

(Figure 12).

Figure 11 - Connecting vent components

Figure 12 - Connected vent components

Figure 13 - Elbow Dimensions

Vent elbows.

Vent elbows are available in 90° and 45° configurations. Refer

to Figure 13 for the SV4.5E45 and SV4.5E90 elbow dimensions.

The elbows feature a twist section to allow them to be routed

about the center axis of their initial collar section to align with

the required direction of the next vent run element.

1. Rotate the elbow in a clockwise direction (to avoid the pos-

sibility of unlocking any of the previously connected vent

sections) for proper alignment (Figure 13). See Connecting

the vent pipe for more information.

Locking

Incline

Channel

Appliance Collar or

Vent Section

Arrow

Dimple

Arrow

Dimple

Locking

Incline

Channel

Inches (millimeters)

13-5/8

(346)

15-1/2

(394)

9-7/8

(251)

Non-Swivel

(254)

~45°

~90°

SV4.5E45

(45° elbow)

SV4.5E90

(90° elbow)

SuperiorFireplaces.us.com 126718-01N18

GROUND FLOOR INSTALLATION

Recommended Applications:

• Through the wall using round or square termination

Figure 14 - Horizontal Termination Using One 90° Elbow

Figure 15 - Horizontal Termination Using Two 90° Elbows

Figure 15a - Horizontal Termination Using Three 90° Elbows

(V) Vertical

Minimum

Required

Vertical Pipe

(H) Horizontal

Maximum

Inches (mm) feet (meters) feet (meters)

53" (1346) 1 ft. (0.305) 7 ft. (2.134)

65" (1651) 2 ft. (0.609) 11 ft. (3.353)

77" (1956) 3 ft. (0.914) 20 ft. (6.096)

V + H = 40 feet (12.192 m) maximum

H = 20 feet (6.096 m) maximum

Wall

Firestop

90° Elbow

V + 90· Elbow

Horizontal High

Wind Square

Termination

1' Pipe Min. On

Horizontal Run

53" Min.

Plus ¼''

Rise per

Foot

Wall ﬁrestop/spacer

SV4.5HF**

When using Secure Flex

, use

ceiling ﬁrestop/spacer SF4.5VF.

When using Secure Flex , use wall

ﬁrestop/spacer SF4.5HF.

Wall ﬁrestop/

spacer

SV4.5HF **

Ceiling

ﬁrestop/spacer

SV4.5VF *

Venting with Two 90° Elbows

Vertical (V) Horizontal (H

+ H

)

feet (meters) feet (meters)

5' Min. (1.524) 8' Max (2.439)

6' Min. (1.829) 10' Max (3.048)

7' Min. (2.134) 15' Max (4.572)

20'Min. (6.096) 20' Max (6.096)

VENTING INSTALLATION Continued

Venting with Three 90° Elbows

Vertical (V) Horizontal (H + H

)

feet (meters) feet (meters)

4' Min. (1.219) 20' Max (6.096)

*Firestop/Spacer (SV4.5HF) shown

on the exterior side of the wall. It

may also be installed on the

interior side.

SV4.5 HTSS

Termination

Shown.

10-1/2"

(267 mm)

(178)

5-1/8"

(130 mm)

12-1/8"

(308 mm)

NOTE: Centerline of Vent

Piping is NOT the Same as

the Centerline of the

Framed Opening.

6” to 48” Vent Section,

Telescopic vent section,

Elbow or Appliance Collar

Base of Appliance

(77 mm)

(26 mm)

Adaptor

SV4.5RCH or

SV4.5RCHA

NOTE: When using Secure Flex

use Firestop/Spacer SF4.5HF

See Fireplace

Installation Instructions

For Min. Distance to

Base of Appliance.

SuperiorFireplaces.us.com126718-01N 19

VENTING INSTALLATION Continued

Figure 16 - Vertical (Straight) Installation

Figure 17 - Framing the ceiling opening

Install the Vertical Termination Vent System

These instructions should be used as a guideline and do not super-

sede local codes in any way. Install venting according to local codes,

these instructions, the current National Fuel Gas Code (ANSI-Z223.1)

in the USA or the current standards of CAN/CGA-B149.1 in Canada.

Ensure clearances are in accordance with local installation codes and

the requirements of the gas supplier.

Vertical vent systems terminate through the roof. The minimum

vent height above the roof and/or adjacent walls is speciﬁed in ANSI

Z223.1 (In Canada, the current CAN/CGA-B149.1 installation code)

by major building codes.

Always consult your local codes for speciﬁc requirements. A general

guide to follow is the gas vent rule (see Figure 22, Page 21).

The following ﬁgures and their associated vertical vent tables illus-

trate the various conﬁgurations that are possible for use with these

ﬁreplaces.

Vertical (Straight) Installation

1. Determine the number of straight vent sections required.

See Effective Vent Length on Table 2, Page 16 for more

information. Plan the vent lengths so that a joint does not

occur at the intersection of ceiling or roof joists.

Vertical (Offset) Installation

1. Analyze the vent route and determine the number of vent

sections and elbows required—See Effective Vent Length

on Table 2, Page 14 for more information. Plan the venting

so that a joint does not occur in the ceiling or roof joists. Al-

low for elbows (Figure 13, Page 17). Maintain the minimum

clearances for combustibles (Page 9).

2. Frame the ceiling opening—Use a plumb line from the ceil-

ing above the fireplace to locate the center of the vertical run.

Cut and/or frame an opening, 10 1/2 x 10 1/2” (267 x 267

mm) inside dimensions, about this center mark (Figure 17).

SV4.5FA or

SV4.5FB Flashing

AND SV4.5SC

Storm Collar

SV4.5VF

Firestop/Spacer

1” (26 mm)

Minimum

Clearance to

Combustibles

SV4.5CGV-1

Termination

SV4.5L6/12/24/36/48

Vent Sections

Max. 40 ft

(12.192 m)

1. Attach the vent components to the fireplace—See Con-

necting the vent pipe on Page 17.

2. Attach the vent components to each other—See Connecting

the vent pipe on Page 17.

3. Install firestop/spacer at ceiling—Use SV4.5VF firestop/

spacer at ceiling joists. If there is living space above the

ceiling level, the firestop/ spacer must be installed on the

bottom side of the ceiling. If attic space is above the ceiling,

the firestop/spacer must be installed on the top side of the

joist. Route the vent sections through the framed opening

and secure the firestop/spacer with 8d nails or other appro-

priate fasteners at each corner. Remember to maintain 1” (26

mm) clearance to combustibles, framing members, and attic

or ceiling insulation when running vertical chimney sections.

The gap between the vent pipe and a vertical firestop can be

sealed with non-combustible caulking.

4. Support the vertical vent run sections—Support the vertical

portion of the venting system every 8 ft (2.4 m) above the

fireplace vent outlet. One method of support is by utilizing

field provided support straps (conventional plumber’s tape).

Secure the plumber’s tape to the framing members with nails

or screws. Loop the tape around the vent, securing the ends

of the tape to the framing. If desired, sheet metal screws #6

x 1/2” length may be used to secure the support straps to

the vent pipe (Figure 18, Page 20).

Roof

Framing

Ceiling

Framing

Plumb Bob

10-1/2” (267 mm)

minimum

10-1/2” (267 mm)

minimum

SuperiorFireplaces.us.com 126718-01N20

VENTING INSTALLATION Continued

Figure 18 - Supporting the Vertical Vent Run

Figure 19 - Roof Framing Dimensions

Figure 20 - Installing the Storm Collar

Blocking

Support straps

(Plumber’s tape)

8 ft (2.4 m)

maximum

1” (26 mm)

minimum

clearance to

combustibles

1. Change vent direction of horizontal/inclined run—Install

the SV4.5E45 and SV4.5E90 elbows in the same manner as

the straight vent sections. See Vent elbows on Page 17 for

more information.

2. Continue installation of horizontal/inclined sections—Con-

tinue with the installation of the straight vent sections in

horizontal/inclined run. Install support straps every 5 ft (1.52

m) along horizontal/inclined vent runs using conventional

plumber’s tape. Rise per foot run ratios are acceptable all

the way to level. For best results, maintain the horizontal/

inclined run in a straight (no dips), slightly elevated plane

of approximately 1/4” per 1 ft (20 mm per 1 m). Maintain

the required clearances to combustibles (Page 9).

3. Frame the roof opening—Identify the location for the vent

at the roof. Cut and/or frame opening (Figure 19).

Pitch C D

0/12 10 1/2” (267 mm) 10 1/2” (267 mm)

6/12 10 1/2” (267 mm) 12” (305 mm)

12/12 10 1/2” (267 mm) 17 3/4” (451 mm)

1. Install the roof flashing—Extend the vent sections through

the roof structure. Install the roof flashing over the vent sec-

tion and position such that the vent column rises vertically

(use carpenters level). Nail along perimeter to secure flashing

or adjust roofing to overlap the flashing edges at top and

sides only and trim where necessary. Seal the top and both

sides of the flashing with waterproof caulking.

2. Install the storm collar—Install the storm collar, supplied

with the flashing, over the vent/flashing joint (Figure 20).

Loosen the storm collar screw. Slide collar down until it meets

the top of the flashing. Tighten the adjusting screw. Apply

non-combustible caulking or mastic around the circumfer-

ence of the joint to provide a water tight seal.

Storm

Collar

Figure 21 - Installing the Vertical Termination

1. Install the vertical termination—The ﬁnal step involves installation

of the SV4.5CGV-1 vertical termination. Align the termination over the

end of the previously installed section, adjusting the radial alignment

until the four (4) locking dimples of the termination are aligned with

the inlets of the four (4) incline channels of the last vent section. Push

the termination down until it fully engages, then twist the termination

clockwise running the dimples down and along the incline channels

until they seat at the end of the channels. If the vent system extends

more than 5 ft (1.5 m) above the roof ﬂashing, stabilizers may be

necessary. Additional screws may be used at section joints for added

stability. Guide wires or roof support assemblies may be attached

to the joint for additional support on multiple joint conﬁgurations.

La page est en cours de chargement...

Superior Fireplaces DRL4543 Mode d'emploi

Marque: Superior Fireplaces

Modèle: DRL4543

Catégorie: Cheminées

Taper: Mode d'emploi

Télécharger le PDF

rapport

dans d''autres langues

English: Superior Fireplaces DRL4543 Operating instructions

Superior Fireplaces DRL4543 Mode d'emploi

Superior Fireplaces DRL4543 Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents