AJA OG-3GDA-1x9 Manuel utilisateur

Marque: AJA

Modèle: OG-3GDA-1x9

Catégorie: Équipement musical supplémentaire

Taper: Manuel utilisateur

Ce manuel convient également à

OG-3GDA-2x4

OG-3GDA Series

openGear Cards

Version 1.2r1

Published January 2, 2020

Installation and Operation Guide

OG-3GDA Series openGear Cards v1.2r1 2 www.aja.com

Notices

Trademarks

AJA® and Because it matters.® are registered trademarks of AJA Video Systems, Inc.

for use with most AJA products. AJA™ is a trademark of AJA Video Systems, Inc. for

use with recorder, router, software and camera products. Because it matters.™ is a

trademark of AJA Video Systems, Inc. for use with camera products.

Corvid Ultra®, lo®, Ki Pro®, KONA®, KUMO®, ROI® and T-Tap® are registered trademarks of

AJA Video Systems, Inc.

AJA Control Room™, KiStor™, Science of the Beautiful™, TruScale™, V2Analog™ and

V2Digital™ are trademarks of AJA Video Systems, Inc.

All other trademarks are the property of their respective owners.

this manual is subject to change without notice. No part of the document may be

reproduced or transmitted in any form, or by any means, electronic or mechanical,

including photocopying or recording, without the express written permission of AJA

Video Systems, Inc.

Contacting AJA Support

When calling for support, have all information at hand prior to calling. To contact AJA

for sales or support, use any of the following methods:

Telephone +1.530.271.3190

FAX +1.530.271.3140

Web https://www.aja.com

Support Email support@aja.com

Sales Email sales@aja.com

OG-3GDA Series openGear Cards v1.2r1 3 www.aja.com

Contents

Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Contacting AJA Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Chapter 1 – Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Card Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

OG-3GDA-1x9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

OG-3GDA-2x4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

LED Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Block Diagram for OG-3GDA-1x9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Block Diagram for OG-3GDA-2x4 in Dual 1x4 Mode . . . . . . . . . . . . . . . . 6

Block Diagram for OG-3GDA-2x4 in Single 1x8 Mode . . . . . . . . . . . . . . . 7

I/O Connections for OG-3GDA-1x9. . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Inverted and Non-Inverted Outputs . . . . . . . . . . . . . . . . . . . . . . . . . .7

I/O Connections for OG-3GDA-2x4, Dual 1x4 Mode . . . . . . . . . . . . . . . . . . 8

Inverted and Non-Inverted Outputs . . . . . . . . . . . . . . . . . . . . . . . . . .8

I/O Connections for OG-3GDA-2x4, Single 1x8 Mode . . . . . . . . . . . . . . . . .8

Inverted and Non-Inverted Outputs . . . . . . . . . . . . . . . . . . . . . . . . . .8

Signal Indicators in the DashBoard Control System . . . . . . . . . . . . . . . . 9

User Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

DashBoard Control System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

openGear and AJA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Rear OG-3GDA Series Card Installation . . . . . . . . . . . . . . . . . . . . . . . 12

Front OG-3GDA Series Card Installation. . . . . . . . . . . . . . . . . . . . . . . 13

Cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Chapter 2 – Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Using the DashBoard Control System. . . . . . . . . . . . . . . . . . . . . . . . . . 15

Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Conguration Settings Stored in OG Card . . . . . . . . . . . . . . . . . . . . . 15

Control Interface Basic Components . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Basic Tree View of Frames and Cards. . . . . . . . . . . . . . . . . . . . . . . . . 16

Card Information and Status. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Parameter Controls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Card Tab Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Input Status Tab Screen—Dual 2x4 Mode . . . . . . . . . . . . . . . . . . . . . 18

Input Status Tab Screen—Single 1x8 Mode . . . . . . . . . . . . . . . . . . . . 19

Setup Tab Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Uploading New Software. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Rebooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Appendix A – Specications . . . . . . . . . . . . . . . . . . . . . . . . 24

OG-3GDA-1x9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

OG-3GDA-2x4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Appendix B – Safety and Compliance . . . . . . . . . . . . . . . . . . 26

Warranty and Liability Information . . . . . . . . . . . . . . . . . . . . 35

Limited Warranty on Hardware. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Limitation of Liability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Governing Law and Language; Your Rights . . . . . . . . . . . . . . . . . . . . . . 35

Index. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37

OG-3GDA Series openGear Cards v1.2r1 4 www.aja.com

Chapter 1 – Introduction

Card Overview

AJA’s OG-3GDA Series cards are state-of-the-art, openGear-compatible, 3G-SDI

distribution amplifiers.

Features

• openGear compatible card (requires 2 slots, rear card included)

• Use with openGear 2RU frames

• Controlled by DashBoard network control software

• Automatic detection and re-clocking of 270Mb, 1.5Gb, and 3Gb SDI data rates

• Excellent input jitter tolerance and low jitter re-clocked outputs

• Input Present and Input SMPTE Lock LEDs (OG-3GDA-1x9)

• Input Present LEDs (OG-3GDA-2x4)

• Hot-swap capable

• 5 year warranty

OG-3GDA-1x9

For the OG-3GDA-1x9, the incoming SD, HD or 3G signal is distributed to each

of the nine 3G-SDI outputs, allowing the same signal to be sent to multiple

destinations simultaneously.

If the incoming SD, HD or 3G signal is one of the five SMPTE rates (270 Mbps, 1.483

Gbps, 1.485 Gbps, 2.966 Gbps, 2.970 Gbps), the signal will be reclocked, and both

the SMPTE Lock LED and Signal Present LED will illuminate. Otherwise, if a non-

SMPTE input is detected, the signal will bypass the reclocker and only the Signal

Present LED will illuminate.

OG-3GDA Series openGear Cards v1.2r1 5 www.aja.com

OG-3GDA-2x4

The OG-3GDA-2x4 offers two modes: Dual 1x4 or Single 1x8. In either mode, the

OG-3GDA-2x4 allows the same signal or signals to be sent to multiple destinations

simultaneously.

The incoming SD, HD or 3G signal(s) will be reclocked if it is one of the five SMPTE

rates (270 Mbps, 1.483 Gbps, 1.485 Gbps, 2.966 Gbps, 2.970 Gbps). Otherwise the

signal(s) will bypass the reclocker and be present at the outputs.

When a SD, HD, or 3G signal is detected, regardless of its compliance to SMPTE

standards, the Signal Present 1 and/or Signal Present 2 LEDs will illuminate,

depending on where the signal input is detected.

Dual 1x4 Mode

In Dual 1x4 Mode, the incoming SD, HD or 3G signals coming in through SDI Input

1 and SDI Input 2 are distributed to the two corresponding sets of four 3G-SDI

outputs. The two DAs are completely independent.

Single 1x8 Mode

In Single 1x8 Mode, the SD, HD or 3G signal coming in through SDI Input 1 is

distributed to the eight 3G-SDI outputs. Both Signal Present LEDs will illuminate

when a signal is present on SDI in 1.

LED Indicators

For OG-3GDA-1x9

LEDs on the front (near door) of each card indicate, from top to bottom:

• DC power detected (green)

• Input signal present (green)

• Input reclocker locked (green)

For OG-3GDA-2x4

LEDs on the front (near door) of each card indicate, from top to bottom:

• DC power detected (green)

• Input 1 signal present (green)

• Input 2 signal present (green)

OG-3GDA Series openGear Cards v1.2r1 6 www.aja.com

Block Diagram for OG-3GDA-1x9

Figure 1. OG-3GDA-1x9 Converter, Simplified Block Diagram

3G-SDI with

Embedded Audio In

3G-SDI with

Embedded Audio Out

SDI Out 1

Outputs pass

embedded audio

and metadata

SDI Out 2

SDI Out 3

SDI Out 4

Cable

ReClock

SDI Out 5

SDI Out 6

SDI Out 7

SDI Out 8

SDI Out 9

Control

DashBoard

Block Diagram for OG-3GDA-2x4 in Dual 1x4 Mode

Figure 2. OG-3GDA-2x4 Converter in Dual 1x4 Mode, Simplified Block Diagram

3G-SDI with

Embedded Audio In

3G-SDI with

Embedded Audio Out

SDI 1 Out 1

Outputs pass

embedded audio

and metadata

SDI 1 Out 2

SDI 1 Out 3

SDI 1 Out 4

3G-SDI with

Embedded Audio In

3G-SDI with

Embedded Audio Out

Outputs pass

embedded audio

and metadata

SDI 2 Out 1

SDI 2 Out 2

SDI 2 Out 3

SDI 2 Out 4

SDI Input 1

SDI Input 2

Cable

ReClock

Control

DashBoard

OG-3GDA Series openGear Cards v1.2r1 7 www.aja.com

Block Diagram for OG-3GDA-2x4 in Single 1x8 Mode

Figure 3. OG-3GDA-2x4 Converter in 1x8 Mode, Simplified Block Diagram

3G-SDI with

Embedded Audio In

3G-SDI with

Embedded Audio Out

SDI 1 Out 1

Outputs pass

embedded audio

and metadata

SDI 1 Out 2

SDI 1 Out 3

SDI 1 Out 4

SDI 1 Out 5

SDI 1 Out 6

SDI 1 Out 7

SDI 1 Out 8

SDI Input 1

Cable

ReClock

Control

DashBoard

I/O Connections for OG-3GDA-1x9

Figure 4. Rear View of OG-3GDA-1x9 Card Connectors

Input

BNC

Output 1*

BNC

Output 3*

BNC

Output 5

BNC

Output 7*

BNC

Output 9*

BNC

Output 2

BNC

Output 4*

BNC

Output 6

BNC

Output 8

BNC

* Non Inverting Outputs

Inverted and Non-Inverted Outputs

Five of the outputs (1, 3, 4, 7, 9) are non-inverting. These are suitable for level-

sensitive signaling, such as DVB-ASI. The other four outputs (2, 5, 6, 8) are

identical, except inverted. All outputs are fully SDI compatible.

OG-3GDA Series openGear Cards v1.2r1 8 www.aja.com

I/O Connections for OG-3GDA-2x4, Dual 1x4 Mode

Figure 5. Rear View of OG-3GDA-2x4 Card Connectors, Dual 1x4 Mode

SDI Input 1

BNC (J1)

SDI Input 2

BNC (J2)

SDI 1 Out 2*

BNC (J4)

SDI 1 Out 4

BNC (J6)

SDI 2 Out 2*

BNC (J8)

SDI 2 Out 4*

BNC (J10)

SDI 1 Out 1

BNC (J3)

SDI 1 Out 3*

BNC (J5)

SDI 2 Out 1

BNC (J7)

SDI 2 Out 3

BNC (J9)

* Non Inverting Outputs

Inverted and Non-Inverted Outputs

In Dual 1x4 Mode, four of the outputs (SDI 1 Out 2, SDI 1 Out 3, SDI 2 Out 2, SDI 2

Out 4) are non-inverting. These are suitable for level-sensitive signaling, such as

DVB-ASI. The other four outputs (SDI 1 Out 1, SDI 1 Out 4, SDI 2 Out 1, SDI 2 Out 3)

are identical, except inverted. All outputs are fully SDI compatible.

I/O Connections for OG-3GDA-2x4, Single 1x8 Mode

Figure 6. Rear View of OG-3GDA-2x4 Card Connectors, 1x8 Mode

SDI Input 1

BNC (J1)

SDI Out 2*

BNC (J4)

SDI Out 4

BNC (J6)

SDI Out 6*

BNC (J8)

SDI Out 8*

BNC (J10)

SDI Out 1

BNC (J3)

SDI Out 3*

BNC (J5)

SDI Out 5

BNC (J7)

SDI Out 7

BNC (J9)

* Non Inverting Outputs

Inverted and Non-Inverted Outputs

In 1x8 Mode, four of the outputs (SDI Out 2, SDI Out 3, SDI Out 6, SDI Out 8) are

non-inverting. These are suitable for level-sensitive signaling, such as DVB-ASI.

The other four outputs (1, 4, 5, 7) are identical, except inverted. All outputs are

fully SDI compatible.

OG-3GDA Series openGear Cards v1.2r1 9 www.aja.com

Signal Indicators in the DashBoard Control System

Card Alarm State – Red

This potential card state will result in a red alarm indicator:

• HW Status Unsupported Rear Module

Card Alarm State – Yellow

When the signal is either not present or is not locked, the DashBoard Control

System shows a yellow Card State alarm: "Signal Status No Signal." Additionally,

under the Input Status tab, the Signal Status is shown as "No Signal," and the

Input Lock is shown as "No Lock."

Figure 7. Signal not present or not locked

OG-3GDA Series openGear Cards v1.2r1 10 www.aja.com

Card Alarm State – Green

When there is a valid input signal detected, the DashBoard Control System shows

a green Card State. Additionally, under the Input Status tab, the Signal Status is

shown as "Signal Present," and the Input Lock is shown as "Locked." The detected

Data Rate of the SDI Signal is also indicated (for example, "1.5 Gbps").

Figure 8. Signal is present and locked

User Controls

The OG-3GDA Series cards can be used right out of the box for many applications,

since they are designed to recognize inputs and perform standard actions

automatically. However, you can also remotely monitor the OG-3GDA Series

through the DashBoard Control System for an openGear Frame.

OG-3GDA Series openGear Cards v1.2r1 11 www.aja.com

DashBoard Control System

The DashBoard Control System, created by Ross Video, provides a control

interface between Windows, macOS and Linux computers and the cards installed

in an openGear frame. DashBoard operates through TCP/IP communication

and requires an Ethernet connection between the controlling computer and an

openGear frame.

For details about acquiring and using the DashBoard Control System, refer to

"Using the DashBoard Control System" on page 15.

openGear and AJA

openGear is an open-architecture, modular frame system designed by Ross

Video and supported by a diverse range of terminal equipment manufacturers,

including AJA. Ross Video manufactures the frames, power supplies and network

cards for openGear. AJA is a reseller of the openGear frames.

AJA Video is a leading manufacturer of video interface technologies, converters,

digital video recording solutions and professional cameras, bringing high-

quality, cost-effective products to the professional, broadcast and post-

production markets. AJA products, including openGear cards, are designed and

manufactured at our facilities in Grass Valley, California.

Installation

Summary

Installing an OG-3GDA Series card into an OG-X-FR openGear frame consists of

the following steps:

• Install the Rear Panel onto the back of the frame corresponding to the slot pair

you will be using for the OG-3GDA Series card.

• Insert the OG-3GDA Series card into the frame in the right (even numbered)

slot of the pair.

• Connect the BNC cabling to the Rear Panel.

ESD Susceptibility - Static discharge can cause serious damage to sensitive

semiconductor devices. Avoid handling circuit boards in high static

environments such as carpeted areas, and when wearing synthetic fiber

clothing. Always exercise proper grounding precautions when working on circuit

boards and related equipment.

Unpacking

Unpack each openGear product you received from the shipping container and

ensure that all items are included. If any items are missing or damaged, contact

your sales representative or AJA directly.

Parts List

Quantity Description

1 OG-3GDA Series Front Card in ESD bag

1 10 BNC Rear Card

OG-3GDA Series openGear Cards v1.2r1 12 www.aja.com

Rear OG-3GDA Series Card Installation

1. Ensure that the frame is properly installed.

2. Locate the card frame slot on the rear of the openGear frame into which you

wish to install the openGear card.

NOTE: An OG-3GDA Series card occupies two slots in the frame.

3. Using a Phillips screwdriver, unscrew the top screw from the desired blank

rear plate and remove the rear plate.

4. Seat the bottom of the Rear Card in the seating slot at the base of the frame

back plane.

Figure 9. Rear Card Inserting Into Frame Seating Slot

5. Align the top screw of the Rear Card with the screw hole on the top edge of

the frame back plane.

6. Ensure the Rear Card aligns with the desired card slot before tightening the

screw.

7. Using a Phillips screwdriver, fasten the Rear Card to the frame back plane.

Do not over tighten.

Figure 10. Rear Card Inserted Into Frame Seating Slot

8. Ensure proper frame cooling and ventilation by having all rear frame slots

covered with rear modules or blank metal plates if plates are not pre-

installed.

OG-3GDA Series openGear Cards v1.2r1 13 www.aja.com

Front OG-3GDA Series Card Installation

1. Open the openGear frame door as follows:

A. Gently pull the side door tabs towards the center of the door, releasing the

door from the frame.

B. Using both hands, pull the door towards you. The door extender arms

prevent the door from falling.

2. Locate the Rear Card you installed as described above. The interior slot

number is dependent on the slot combinations into which you installed the

Rear Card. This allows adequate spacing to avoid damaging the card, the

cards installed in the neighboring slots, or both.

3. Hold the card by the edges and carefully align the card edges with the rails

inside the frame. The slots are numbered starting from the left-most slot

when facing the frame front.

IMPORTANT: OG-3GDA Series cards are installed into the right (even numbered) slot of the

pair in order to connect with the rear panel.

4. Fully insert the card into the frame until the card is properly seated in the

Rear Card. There are two stages to inserting the card:

A. After you feel the card's first click, its position in the frame will resemble the

photograph below in Figure 11.

B. Next, press against the white plastic tab again until you feel the second

click. The card's position will resemble the photograph below in Figure 12.

NOTE: Some cards require more pressure than others to be fully inserted. Make sure that

the plastic tab at the bottom of the front edge of the card is completely upright. If

it is tilting forward, the card is not yet fully inserted.

Figure 11. The card on the left is already fully inserted. The card on the right

is not yet fully inserted, as indicated by the white plastic tab tilting

forward.

OG-3GDA Series openGear Cards v1.2r1 14 www.aja.com

Figure 12. The white plastic tab for the card on the right is now upright. Both

cards are shown fully inserted.

5. Close the frame door as follows:

A. Slide the door into the frame.

B. Pull and release the door tabs to ensure the frame door is securely locked

to the frame.

Cabling

Refer to "I/O Connections for OG-3GDA-1x9" on page 7, "I/O Connections for OG-

3GDA-2x4, Dual 1x4 Mode" on page 8, and "I/O Connections for OG-3GDA-2x4,

Single 1x8 Mode" on page 8 to identify the input and output signal connectors.

OG-3GDA Series openGear Cards v1.2r1 15 www.aja.com

Chapter 2 – Operation

Using the DashBoard Control System

The DashBoard Control System is available as a free download from the openGear

DashBoard Software Download webpage:

https://www.opengear.tv/frame-and-control/control-system/download/

Ross Video offers comprehensive documentation that covers the extensive

capabilities of the DashBoard Control System:

https://www.rossvideo.com/support/product-documentation/dashboard/

This AJA OG-3GDA Series manual addresses only those essential aspects of the

DashBoard Control System needed to control the OG-3GDA Series card.

Requirements

The DashBoard Control System requires the following components:

• openGear frame with a Frame Controller card

• Ethernet connection betweeen the controlling computer and the openGear

frame

NOTE: The openGear frame ships from AJA with the MFC-8322-S Frame Controller card

for controlling the new AJA DashBoard cards. The openGear frame also supports

the MFC-0G3-N Advanced Networking Frame Controller card, which can be used

to control compatible OG cards.

DashBoard automatically discovers openGear and DashBoard Connect devices,

such as openGear frames and cards that are present and accessible on your

network.

Configuration Settings Stored in OG Card

Configuration settings made through DashBoard are stored in the

OG-3GDA Series unit through subsequent power cycles.

Control Interface Basic Components

The basic components of the DashBoard Control System user interface consist of

the basic tree view of frames and cards, the card information and status panel,

and the parameter controls panel. These elements are shown below.

OG-3GDA Series openGear Cards v1.2r1 16 www.aja.com

Figure 13. Main Sections of the DashBoard User Interface

Parameter

Controls

Card Information

and Status

Basic Tree View of

Frames and Cards

Basic Tree View of Frames and Cards

The basic tree view in the left column shows the frames and cards that are

discoverable by DashBoard on your network.

Card Information and Status

The card information and status panel, shown in the middle panel, display the

basic status of the card currently selected in DashBoard. The yellow fields in this

panel indicate that they are read-only.

Parameter Controls

The parameter controls panel on the right side of DashBoard shows the tabs and

parameters that are configurable for the selected card. The white fields indicate

that they can be written to, or modified.

OG-3GDA Series openGear Cards v1.2r1 17 www.aja.com

Card Tab Screen

Figure 14. OG-3GDA-2x4 Card Tab Screen in DashBoard

The Card tab screen indicates the basic information about the card itself such as

the card name, hardware status, serial number, software version and other items.

OG-3GDA Series openGear Cards v1.2r1 18 www.aja.com

Input Status Tab Screen—Dual 2x4 Mode

Figure 15. OG-3GDA Series Input Status Tab Screen, Dual 2x4 Mode, in

DashBoard

For Channels 1 and 2, as applicable, the Input Status fields report the Routing

Mode (1x8 or 2x4), the Signal Status, the Input Lock Status, and the Data Rate.

OG-3GDA Series openGear Cards v1.2r1 19 www.aja.com

Input Status Tab Screen—Single 1x8 Mode

Figure 16. OG-3GDA Series Input Status Tab Screen, Single 1x8 Mode, in

DashBoard

The Input Status fields report the Routing Mode (1x8 or 2x4), the Signal Status, the

Input Lock Status, and the Data Rate.

OG-3GDA Series openGear Cards v1.2r1 20 www.aja.com

Setup Tab Screen

Figure 17. OG-3GDA Series Setup Tab Screen in DashBoard

Click on the Setup tab to view and make changes to the card name or to restore

card settings to factory default values.

Card Name - By default, this field is pre-populated with the card name OG-3GDA-

2x4 or OG-3GDA-1x9. You can change the card name by editing the text in the

Card Name field.

NOTE: Changing the Card Name in the Setup tab also changes the name of the card in

the DashBoard tree view.

Factory Settings - If you would like to revert the card settings to factory default

values, click Restore.

Uploading New Software

When available, you can upload updated software to the OG-3GDA Series

through the DashBoard Control System by following the steps below.

To Upload New Software

1. Check the AJA website for new software for your OG-3GDA Series. If new

software is found, download it and uncompress the file archive (zip).

2. Click the Upload button in the lower panel of the DashBoard Control System

to open the Upload Software Wizard.

La page charge ...

AJA OG-3GDA-1x9 Manuel utilisateur

Marque: AJA

Modèle: OG-3GDA-1x9

Catégorie: Équipement musical supplémentaire

Taper: Manuel utilisateur

Ce manuel convient également à

OG-3GDA-2x4

Télécharger le PDF

rapport

dans d''autres langues

italiano: AJA OG-3GDA-1x9 Manuale utente
English: AJA OG-3GDA-1x9 User manual
Deutsch: AJA OG-3GDA-1x9 Benutzerhandbuch
português: AJA OG-3GDA-1x9 Manual do usuário

AJA OG-3GDA-1x9 Manuel utilisateur

Ce manuel convient également à

AJA OG-3GDA-1x9 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents