AJA OG-FIBER-2T-X Manuel utilisateur

OG-FIBER-2T-X
AJA
Marque
AJA
Modèle
OG-FIBER-2T-X
Catégorie
Équipement musical supplémentaire
Taper
Manuel utilisateur

Ce manuel convient également à

OG-Fiber-Series
openGear Card
Version 1.1r1
Published January 3, 2020
Installation and Operation Guide
OG-Fiber-Series openGear Card v1.1r1 2 www.aja.com
Notices
Trademarks
AJA® and Because it matters.® are registered trademarks of AJA Video Systems, Inc.
for use with most AJA products. AJA™ is a trademark of AJA Video Systems, Inc. for
use with recorder, router, software and camera products. Because it matters.™ is a
trademark of AJA Video Systems, Inc. for use with camera products.
Corvid Ultra®, lo®, Ki Pro®, KONA®, KUMO®, ROI® and T-Tap® are registered trademarks of
AJA Video Systems, Inc.
AJA Control Room™, KiStor™, Science of the Beautiful™, TruScale™, V2Analog™ and
V2Digital™ are trademarks of AJA Video Systems, Inc.
All other trademarks are the property of their respective owners.
Copyright
Copyright © 2020 AJA Video Systems, Inc. All rights reserved. All information in
this manual is subject to change without notice. No part of the document may be
reproduced or transmitted in any form, or by any means, electronic or mechanical,
including photocopying or recording, without the express written permission of AJA
Video Systems, Inc.
Contacting AJA Support
When calling for support, have all information at hand prior to calling. To contact AJA
for sales or support, use any of the following methods:
Telephone +1.530.271.3190
FAX +1.530.271.3140
Web https://www.aja.com
Support Email suppor[email protected]
Sales Email sales@aja.com
OG-Fiber-Series openGear Card v1.1r1 3 www.aja.com
Contents
Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Copyright . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Contacting AJA Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Chapter 1 – OG-FIBER-Series . . . . . . . . . . . . . . . . . . . . . . . . .4
Card Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Block Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Connectors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
openGear and AJA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Parts Supplied . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Rear Fiber Card Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Front Fiber Card Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Cabling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Appendix A – Specications . . . . . . . . . . . . . . . . . . . . . . . . 11
OG-FIBER-TR. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
OG-FIBER-T . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
OG-FIBER-R . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
OG-FIBER-2T. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
OG-FIBER-2R. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
OG-FIBER-TR-MM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
OG-FIBER-T-MM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
OG-FIBER-R-MM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
OG-FIBER-2T-MM. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
OG-FIBER-2R-MM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Appendix B – Safety and Compliance . . . . . . . . . . . . . . . . . . 21
Warranty and Liability Information . . . . . . . . . . . . . . . . . . . . 29
Limited Warranty on Hardware. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Limitation of Liability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Governing Law and Language; Your Rights . . . . . . . . . . . . . . . . . . . . . . 29
OG-Fiber-Series openGear Card v1.1r1 4 www.aja.com
Chapter 1 – OG-FIBER-Series
Card Overview
The OG-FIBER-Series cards are state-of-the-art, openGear-compatible, 3G-SDI to/
from Fiber converter cards, enabling SDI signals to be extended up to 10km over
standard Single-Mode fiber optic cable or 700 m (2296 ft) for OM4 and 300 m
(984 ft) for OM3 for Multi-Mode fiber optic cable.
Ten AJA cards are available:
• OG-FIBER TR, 1-Channel 3G-SDI/LC Single-Mode LC Fiber Transceiver
• OG-FIBER-T, 1-Channel 3G-SDI to Single-Mode LC Fiber Transmitter
• OG-FIBER-R, 1-Channel Single-Mode LC Fiber to 3G-SDI Receiver
• OG-FIBER-2T, 2-Channel 3G-SDI to Single-Mode LC Fiber Transmitter
• OG-FIBER-2R, 2-Channel Single-Mode LC Fiber to 3G-SDI Receiver
• OG-FIBER-TR-MM, 1-Channel 3G-SDI/LC Multi-Mode LC Fiber Transceiver
• OG-FIBER-T-MM, 1-Channel 3G-SDI to Multi-Mode LC Fiber Transmitter
• OG-FIBER-R-MM, 1-Channel Multi-Mode LC Fiber to 3G-SDI Receiver
• OG-FIBER-2T-MM, 2-Channel 3G-SDI to Multi-Mode LC Fiber Transmitter
• OG-FIBER-2R-MM, 2-Channel Multi-Mode LC Fiber to 3G-SDI Receiver
The inputs are re-clocked with best-in-class input jitter tolerance. The two
channel cards have completely independent paths, allowing different SDI rates to
be carried on each channel.
The fiber connector is attached to the main card for added reliability and cost
savings.
NOTE: In order to allow direct fiber connection to the card, and avoid problematic
optical couplers, AJA Fiber openGear cards have the rear connectors attached to
the front card. This means that the card cannot be removed from the frame with
the SFP module, cables, and/or BNC retaining nuts installed.
Features
• Automatic detection and re-clocking of 270Mb, 1.5Gb, and 3Gb SDI data rates
• LC Fiber connectors
• Input Present and Input SMPTE Lock LEDs
• Hot-swap capable
OG-Fiber-Series openGear Card v1.1r1 5 www.aja.com
• All SDI or ber inputs are re-clocked, and SDI inputs are also equalized.
• ASI compatible
• Compatible with DFR-8321 and OG3 openGear frames
• Five-year international warranty with unlimited technical support
NOTE: OG-FIBER-Series cards do not communicate with the DashBoard Control System.
Block Diagram
3G-SDI
Identical
Second Output
Optical
Fiber
Input
3G-SDI
Output
OG-FIBER-R, OG-FIBER-R-MM
Optical
Receiver
Equalize &
Reclock
Optical
Fiber
Out
3G-SDI
Input
3G-SDI Re-clocked
Loop Thru Output
OG-FIBER-T, OG-FIBER-T-MM
Equalize &
Reclock
Optical
Transmitter
Optical
Fiber
Out
3G-SDI
Input
Optical
Fiber
Input
3G-SDI
Output
OG-FIBER-TR and OG-FIBER-TR-MM
Optical
Receiver
Equalize &
Reclock
Equalize &
Reclock
Optical
Transmitter
Optical
Fiber
Input 1
3G-SDI
Output 1
Optical
Fiber
Input 2
3G-SDI
Output 2
OG-FIBER-2R and OG-FIBER-2R-MM
Optical
Receiver
Equalize &
Reclock
Optical
Receiver
Equalize &
Reclock
Optical
Fiber
Out 1
3G-SDI
Input 1
Optical
Fiber
Out 2
3G-SDI
Input 2
OG-FIBER-2T and OG-FIBER-2T-MM
Equalize &
Reclock
Optical
Transmitter
Equalize &
Reclock
Optical
Transmitter
OG-Fiber-Series openGear Card v1.1r1 6 www.aja.com
Connectors
Figure 1. Rear View of Empty Rear Card and Installed Dual Channel Fiber Cards
Output
BNC 1
(J1)
Input
Fiber 1
Input
Fiber 2
Output
BNC 2
(J2)
OG-FIBER-2R
Card Installed
Input
BNC 1
(J1)
Output
Fiber 2
Output
Fiber 1
Input
BNC 2
(J2)
OG-FIBER-2T
Card Installed
Output
BNC
(J1)
Input
Fiber
Output
Fiber
Input
BNC
(J2)
OG-FIBER-TR
Card Installed
OG-FIBER-Rear
Card
Seating tab to be inserted into frame seating slot.
NOTE: On the OG-Fiber-2T card, Output Fiber 2 is located above Output Fiber 1.
Figure 2. Rear View of Empty Rear Card and Installed Single Channel Fiber
Cards
Output
BNC 1
(J1)
Input
Fiber
Output
BNC 2
(J2)
OG-FIBER-R
Card Installed
Input
BNC
(J1)
Output
Fiber
Output
Loop
BNC
(J2)
OG-FIBER-T
Card Installed
OG-FIBER-Rear
Card
Seating tab to be inserted into frame seating slot.
Indicators
LEDs on the front (near door) of each card indicate, from top to bottom:
2T and 2R Cards
• DC power detected (green)
• Input 1 signal present (green)
• Input 1 SMPTE locked (green)
• Input 2 signal present (green)
• Input 2 SMPTE locked (green)
TR Cards
• DC power detected (green)
• Optical input signal present (green)
• Optical input SMPTE locked (green)
• SDI input signal present (green)
OG-Fiber-Series openGear Card v1.1r1 7 www.aja.com
• SDI input SMPTE locked (green)
Single Channel Cards
• DC power detected (green)
• Signal present (green)
• SMPTE locked (green)
openGear and AJA
openGear is an open-architecture, modular frame system designed by Ross
Video and supported by a diverse range of terminal equipment manufacturers,
including AJA. Ross Video manufactures the frames, power supplies and network
cards for openGear.
AJA Video is a leading manufacturer of video interface technologies, converters,
digital video recording solutions and professional cameras, bringing high-
quality, cost-effective products to the professional, broadcast and post-
production markets. AJA products, including openGear cards, are designed and
manufactured at our facilities in Grass Valley, California.
Parts Supplied
Each OG-FIBER card is shipped with:
• OG-FIBER card in an ESD bag
• Fiber Rear Card
• SFP module in ESD bag
• BNC nuts and star washers
Installation
CLASS 1
LASER
PRODUCT
Warning! Active ber-optic cables emit radiation invisible to the human eye. Do
not look directly at the end of an active ber-optic cable or the ber connector
on an OG-FIBER-2T, OG-FIBER-2T-MM, OG-FIBER-TR, OG-FIBER-TR-MM, OG-
FIBER-T, OG-FIBER-T-MM; these models are Class 1 Laser Products.
Summary
Installing an OG-FIBER card into a DFR-8321 or OG3 openGear frame consists of
the following steps:
1. Install a Rear Fiber Card into the frame.
2. Ensure the SFP module is removed from the Front Fiber Card.
3. Insert the Front Fiber card in the left (odd numbered) slot of the pair.
4. Install BNC connector retaining nuts and washers.
5. Insert the SFP module into the card from the rear of the frame.
6. Connect the BNC and Fiber cabling.
OG-Fiber-Series openGear Card v1.1r1 8 www.aja.com
ESD Susceptibility - Static discharge can cause serious damage to sensitive
semiconductor devices. Avoid handling circuit boards in high static
environments such as carpeted areas, and when wearing synthetic ber clothing.
Always exercise proper grounding precautions when working on circuit boards
and related equipment.
Unpacking
Unpack each openGear product you received from the shipping container and
ensure that all items are included. If any items are missing or damaged, contact
your sales representative or AJA directly.
Rear Fiber Card Installation
1. Power down the openGear frame.
2. Ensure that the frame is properly installed.
3. Locate the card frame slot on the rear of the openGear frame into which you
wish to install the openGear card.
NOTE: An OG-FIBER card occupies two slots in the frame.
4. Using a Phillips screwdriver, unscrew the top screw from the desired blank
rear plate and remove the rear plate.
5. Seat the bottom of the Rear Card in the seating slot at the base of the frame
back plane (Figure 3).
Figure 3. Rear Card Inserted Into Frame Seating Slot
6. Align the top screw of the Rear Card with the screw hole on the top edge of
the frame back plane.
7. Ensure the Rear Card aligns with the desired card slot before tightening the
screw.
8. Using a Phillips screwdriver, fasten the Rear Card to the frame back plane.
Do not over tighten.
9. Ensure proper frame cooling and ventilation by having all rear frame slots
covered with rear modules or blank metal plates if plates are not pre-
installed.
Front Fiber Card Installation
Caution! The SFP module must be removed from an OG-FIBER card before
inserting the card into or removing the card from an openGear frame.
1. If necessary, remove the SFP module from the Front Card by lifting the lever
and pulling out the module.
OG-Fiber-Series openGear Card v1.1r1 9 www.aja.com
2. If nuts and washers are pre-installed on the BNC connectors, they must be
removed before inserting the card in the frame.
3. Open the openGear frame door as follows:
A. Gently pull the side door tabs towards the center of the door, releasing the
door from the frame.
B. Using both hands, pull the door towards you. The door extender arms
prevent the door from falling.
4. Locate the Rear Card you installed as described above. The interior slot
number is dependent on the slot combinations into which you installed the
Rear Card. This allows adequate spacing to avoid damaging the card, the
cards installed in the neighboring slots, or both.
5. Hold the card by the edges and carefully align the card edges with the rails
inside the frame. The slots are numbered starting from the left-most slot
when facing the fame front.
NOTE: OG-FIBER cards are installed into the left (odd numbered) slot of the pair.
6. Fully insert the card into the frame until the card is properly seated in the
Rear Card. (Figure 4).
Figure 4. OG-FIBER Card Inserted Into Left Slot
7. Secure the card in the frame by the BNC connectors using the star washers
and nuts provided (Figure 5).
Figure 5. BNC Star Washer and Nut Installation
8. Insert the SFP ber module into the socket until it clicks and locks. The lever
handle is on the left (Figure 6).
OG-Fiber-Series openGear Card v1.1r1 10 www.aja.com
Figure 6. Fiber SFP Installation
NOTE: The SFP module must match the card’s capabilities for proper operation. Input
and output triangles next to the fiber ports identify which are inputs and which
are outputs.
Figure 7. An SFP Module
9. Close the frame door as follows:
A. Slide the door into the frame.
B. Pull and release the door tabs to ensure the frame door is securely locked
to the frame.
Cabling
Refer to Figure 1 on page 6 and Figure 2 on page 6 to identify the input and
output signal connectors.
NOTE: Keep the protective rubber plug in the SFP module until the fiber cabling is
actually connected to the module.
OG-Fiber-Series openGear Card v1.1r1 11 www.aja.com
Appendix A – Specications
OG-FIBER-TR
Video Formats
• 100 Mbps - 3 Gbps, format agnostic
Video Input Digital
• 1-Channel independent 3G-SDI, SMPTE-259/292/424
• 1-Channel Single Mode LC Fiber connector, SMPTE-297
• Nominal Wavelength: 1310 nm
• Optical Sensitivity: -18dBm (min)
• Optical Power: -5dBm (min), 0dBm (max)
• Extinction Ratio: 7.5dB (Typ)
Video Output Digital
• 1-Channel independent 3G-SDI, SMPTE-259/292/424
• 1-Channel Single Mode LC Fiber connector, SMPTE-297
• Nominal Wavelength: 1310 nm
• Optical Sensitivity: -18dBm (min)
• Optical Power: -5dBm (min), 0dBm (max)
• Extinction Ratio: 7.5dB (Typ)
Reclocking
• 270 Mbps, 1.483 Gbps, 1.485 Gbps, 2.966 Gbps, 2.970 Gbps - Auto Select
• All other rates are passed through and not reclocked
Size (w x d x h)
• openGear standard form factor, front slot and rear card
• Two slots required for each card
Power
• openGear frame compatible, 2.5 watts max per card
Environment
• Safe Operating Temperature: 0 to 40 degrees C (32 to 104 degrees F)
• Safe Storage Temperature (Power OFF): -40 to 60 degrees C (-40 to 140
degrees F)
• Operating Relative Humidity: 10-90% noncondensing
• Operating Altitude: <3,000 meters (<10,000 feet)
OG-Fiber-Series openGear Card v1.1r1 12 www.aja.com
OG-FIBER-T
Video Formats
• 100 Mbps - 3 Gbps, format agnostic
Video Input Digital
• 1-Channel independent 3G-SDI with SDI Loop out, SMPTE-259/292/424
Video Output Digital
• 1-Channel independent 3G-SDI Loop out, SMPTE-259/292/424
• 1-Channel Single Mode LC Fiber connector, SMPTE-297
• Nominal Wavelength: 1310 nm
• Optical Power: -5dBm (min), 0dBm (max)
• Extinction Ratio: 7.5dB (Typ)
Reclocking
• 270 Mbps, 1.483 Gbps, 1.485 Gbps, 2.966 Gbps, 2.970 Gbps - Auto Select
• All other rates are passed through and not reclocked
Size (w x d x h)
• openGear standard form factor, front slot and rear card
• Two slots required for each card
Power
• openGear frame compatible, 2.5 watts max per card
Environment
• Safe Operating Temperature: 0 to 40 degrees C (32 to 104 degrees F)
• Safe Storage Temperature (Power OFF): -40 to 60 degrees C (-40 to 140
degrees F)
• Operating Relative Humidity: 10-90% noncondensing
• Operating Altitude: <3,000 meters (<10,000 feet)
OG-Fiber-Series openGear Card v1.1r1 13 www.aja.com
OG-FIBER-R
Video Formats
• 100 Mbps - 3 Gbps, format agnostic
Video Input Digital
• 1-Channel Single Mode LC Fiber connector, SMPTE-297
• Nominal Wavelength: 1260 - 1620 nm
• Optical Sensitivity: -18dBm (min)
Video Output Digital
• 1-Channel Dual matching 3G-SDI Outputs, SMPTE-259/292/424
Reclocking
• 270 Mbps, 1.483 Gbps, 1.485 Gbps, 2.966 Gbps, 2.970 Gbps - Auto Select
• All other rates are passed through and not reclocked
Size (w x d x h)
• openGear standard form factor, front slot and rear card
• Two slots required for each card
Power
• openGear frame compatible, 2.5 watts max per card
Environment
• Safe Operating Temperature: 0 to 40 degrees C (32 to 104 degrees F)
• Safe Storage Temperature (Power OFF): -40 to 60 degrees C (-40 to 140
degrees F)
• Operating Relative Humidity: 10-90% noncondensing
• Operating Altitude: <3,000 meters (<10,000 feet)
OG-Fiber-Series openGear Card v1.1r1 14 www.aja.com
OG-FIBER-2T
Video Formats
• 100 Mbps - 3 Gbps, format agnostic
Video Input Digital
• 2-Channel independent 3G-SDI Inputs, SMPTE-259/292/424
Video Output Digital
• 2-Channel independent Single Mode LC Fiber Outputs, SMPTE-297
• Nominal Wavelength: 1310 nm
• Optical Power: -5dBm (min), 0dBm (max)
• Extinction Ratio: 7.5dB (Typ)
Reclocking
• 270 Mbps, 1.483 Gbps, 1.485 Gbps, 2.966 Gbps, 2.970 Gbps - Auto Select
• All other rates are passed through and not reclocked
Size (w x d x h)
• openGear standard form factor, front slot and rear card
• Two slots required for each card
Power
• openGear frame compatible, 2.5 watts max per card
Environment
• Safe Operating Temperature: 0 to 40 degrees C (32 to 104 degrees F)
• Safe Storage Temperature (Power OFF): -40 to 60 degrees C (-40 to 140
degrees F)
• Operating Relative Humidity: 10-90% noncondensing
• Operating Altitude: <3,000 meters (<10,000 feet)
OG-Fiber-Series openGear Card v1.1r1 15 www.aja.com
OG-FIBER-2R
Video Formats
• 100 Mbps - 3 Gbps, format agnostic
Video Input Digital
• 2-Channel independent Single Mode LC Fiber Outputs, SMPTE-297
• Nominal Wavelength: 1260 - 1620 nm
• Optical Sensitivity: -18dBm (min)
Video Output Digital
• 2-Channel independent 3G-SDI Outputs, SMPTE-259/292/424
Reclocking
• 270 Mbps, 1.483 Gbps, 1.485 Gbps, 2.966 Gbps, 2.970 Gbps - Auto Select
• All other rates are passed through and not reclocked
Size (w x d x h)
• openGear standard form factor, front slot and rear card
• Two slots required for each card
Power
• openGear frame compatible, 2.5 watts max per card
Environment
• Safe Operating Temperature: 0 to 40 degrees C (32 to 104 degrees F)
• Safe Storage Temperature (Power OFF): -40 to 60 degrees C (-40 to 140
degrees F)
• Operating Relative Humidity: 10-90% noncondensing
• Operating Altitude: <3,000 meters (<10,000 feet)
OG-Fiber-Series openGear Card v1.1r1 16 www.aja.com
OG-FIBER-TR-MM
Video Formats
• 100 Mbps - 3 Gbps, format agnostic
Video Input Digital
• 1-Channel independent 3G-SDI, SMPTE-259/292/424
• 1-Channel Multi-Mode LC Fiber connector, SMPTE-297
• Nominal Wavelength: 850 nm
• Optical Sensitivity: -15dBm (min)
• Optical Power: -7dBm (min), -2dBm (max)
• Extinction Ratio: 7.5dB (Typ)
Video Output Digital
• 1-Channel independent 3G-SDI, SMPTE-259/292/424
• 1-Channel Multi-Mode LC Fiber connector, SMPTE-297
• Nominal Wavelength: 850 nm
• Optical Sensitivity: -15dBm (min)
• Optical Power: -7dBm (min), -2dBm (max)
• Extinction Ratio: 7.5dB (Typ)
Reclocking
• 270 Mbps, 1.483 Gbps, 1.485 Gbps, 2.966 Gbps, 2.970 Gbps - Auto Select
• All other rates are passed through and not reclocked
Size (w x d x h)
• openGear standard form factor, front slot and rear card
• Two slots required for each card
Power
• openGear frame compatible, 2.5 watts max per card
Environment
• Safe Operating Temperature: 0 to 40 degrees C (32 to 104 degrees F)
• Safe Storage Temperature (Power OFF): -40 to 60 degrees C (-40 to 140
degrees F)
• Operating Relative Humidity: 10-90% noncondensing
• Operating Altitude: <3,000 meters (<10,000 feet)
OG-Fiber-Series openGear Card v1.1r1 17 www.aja.com
OG-FIBER-T-MM
Video Formats
• 100 Mbps - 3 Gbps, format agnostic
Video Input Digital
• 1-Channel independent 3G-SDI, SMPTE-259/292/424
Video Output Digital
• 1-Channel independent 3G-SDI Loop out, SMPTE-259/292/424
• 1-Channel Multi-Mode LC Fiber connector, SMPTE-297
• Nominal Wavelength: 850 nm
• Optical Power: -7dBm (min), -2dBm (max)
• Extinction Ratio: 7.5dB (Typ)
Reclocking
• 270 Mbps, 1.483 Gbps, 1.485 Gbps, 2.966 Gbps, 2.970 Gbps - Auto Select
• All other rates are passed through and not reclocked
Size (w x d x h)
• openGear standard form factor, front slot and rear card
• Two slots required for each card
Power
• openGear frame compatible, 2.5 watts max per card
Environment
• Safe Operating Temperature: 0 to 40 degrees C (32 to 104 degrees F)
• Safe Storage Temperature (Power OFF): -40 to 60 degrees C (-40 to 140
degrees F)
• Operating Relative Humidity: 10-90% noncondensing
• Operating Altitude: <3,000 meters (<10,000 feet)
OG-Fiber-Series openGear Card v1.1r1 18 www.aja.com
OG-FIBER-R-MM
Video Formats
• 100 Mbps - 3 Gbps, format agnostic
Video Input Digital
• 1-Channel independent 3G-SDI, SMPTE-259/292/424
• 1-Channel Multi-Mode LC Fiber connector, SMPTE-297
• Nominal Wavelength: 850 nm
• Optical Sensitivity: -15dBm (min)
Video Output Digital
• 1-Channel Dual matching 3G-SDI Outputs, SMPTE-259/292/424
Reclocking
• 270 Mbps, 1.483 Gbps, 1.485 Gbps, 2.966 Gbps, 2.970 Gbps - Auto Select
• All other rates are passed through and not reclocked
Size (w x d x h)
• openGear standard form factor, front slot and rear card
• Two slots required for each card
Power
• openGear frame compatible, 2.5 watts max per card
Environment
• Safe Operating Temperature: 0 to 40 degrees C (32 to 104 degrees F)
• Safe Storage Temperature (Power OFF): -40 to 60 degrees C (-40 to 140
degrees F)
• Operating Relative Humidity: 10-90% noncondensing
• Operating Altitude: <3,000 meters (<10,000 feet)
OG-Fiber-Series openGear Card v1.1r1 19 www.aja.com
OG-FIBER-2T-MM
Video Formats
• 100 Mbps - 3 Gbps, format agnostic
Video Input Digital
• 2-Channel independent 3G-SDI Inputs, SMPTE-259/292/424
Video Output Digital
• 2-Channel independent Multi-Mode LC Fiber Outputs, SMPTE-297
• Nominal Wavelength: 850 nm
• Optical Power: -7dBm (min), -2dBm (max)
• Extinction Ratio: 7.5dB (Typ)
Reclocking
• 270 Mbps, 1.483 Gbps, 1.485 Gbps, 2.966 Gbps, 2.970 Gbps - Auto Select
• All other rates are passed through and not reclocked
Size (w x d x h)
• openGear standard form factor, front slot and rear card
• Two slots required for each card
Power
• openGear frame compatible, 2.5 watts max per card
Environment
• Safe Operating Temperature: 0 to 40 degrees C (32 to 104 degrees F)
• Safe Storage Temperature (Power OFF): -40 to 60 degrees C (-40 to 140
degrees F)
• Operating Relative Humidity: 10-90% noncondensing
• Operating Altitude: <3,000 meters (<10,000 feet)
OG-Fiber-Series openGear Card v1.1r1 20 www.aja.com
OG-FIBER-2R-MM
Video Formats
• 100 Mbps - 3 Gbps, format agnostic
Video Input Digital
• 2-Channel independent Multi-Mode LC Fiber Outputs, SMPTE-297
• Nominal Wavelength: 850 nm
• Optical Sensitivity: -15dBm (min)
Video Output Digital
• 2-Channel independent 3G-SDI Outputs, SMPTE-259/292/424
Reclocking
• 270 Mbps, 1.483 Gbps, 1.485 Gbps, 2.966 Gbps, 2.970 Gbps - Auto Select
• All other rates are passed through and not reclocked
Size (w x d x h)
• openGear standard form factor, front slot and rear card
• Two slots required for each card
Power
• openGear frame compatible, 2.5 watts max per card
Environment
• Safe Operating Temperature: 0 to 40 degrees C (32 to 104 degrees F)
• Safe Storage Temperature (Power OFF): -40 to 60 degrees C (-40 to 140
degrees F)
• Operating Relative Humidity: 10-90% noncondensing
• Operating Altitude: <3,000 meters (<10,000 feet)
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
La page est en cours de chargement...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30

AJA OG-FIBER-2T-X Manuel utilisateur

OG-FIBER-2T-X
AJA
Marque
AJA
Modèle
OG-FIBER-2T-X
Catégorie
Équipement musical supplémentaire
Taper
Manuel utilisateur
Ce manuel convient également à
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents