Candy CTP634SCBB Manuel utilisateur

Marque: Candy

Modèle: CTP634SCBB

Catégorie: Plaques de cuisson

Taper: Manuel utilisateur

Instruction Manual For Induction Hob

ENGLISH

Manuel d’instruction pour plaque à induction

FRANÇAIS

MODEL: CTP634SCBB

THANK YOU FOR PURCHASING THE CANDY INDUCTION HOB. PLEASE READ THIS INSTRUCTION

MANUAL CAREFULLY BEFORE USING THE HOB KEEP IT IN A SAFE PLACE FOR FUTURE

REFERENCE.

SAFETY WARNINGS

PLEASE READ THE FOLLOWING INSTRUCTIONS

CAREFULLY BEFORE USING THE APPLIANCE.

Installation

Electrical Shock Hazard

•Disconnect the appliance from the mains electricity supply

before carrying out any work or maintenance on it.

•Connection to a good earth wiring system is essential and

mandatory.

•Means for disconnection must be incorporated in the fixed

wiring in accordance with the wiring rules.

•Alterations to the domestic wiring system must only be

made by a qualified electrician.

•Failure to follow this advice may result in electrical shock

or death.

Cut Hazard

•Take care - panel edges are sharp.

•Failure to use caution could result in injury or cuts.

Important safety instructions

•Read these instructions carefully before installing or using

this appliance.

•No combustible material or products should be placed on

this appliance at any time.

•Please make this information available to the person

responsible for installing the appliance as it could reduce

your installation costs.

•In order to avoid a hazard, this appliance must be installed

according to these instructions for installation.

•This appliance is to be properly installed and earthed only

by a suitably qualified person.

•This appliance should be connected to a circuit which

incorporates an isolating switch providing full

disconnection from the power supply.

•WARNING: Use only hob guards designed by the

manufacturer of the cooking appliance or indicated by the

manufacturer of the appliance in the instructions for use as

suitable or hob guards incorporated in the appliance. The

use of inappropriate guards can cause accidents.

•Failure to install the appliance correctly could invalidate

any warranty or liability claims.

•Regarding the details of installation, thanks to refer to the

section <Installation>.

Operation and maintenance

Electrical Shock Hazard

•Do not cook on a broken or cracked cooktop. If the cooktop

surface is break or crack, switch the appliance off

immediately at the mains power supply (wall switch) and

contact a qualified technician.

•Switch the cooktop off at the wall before cleaning or

maintenance.

•Failure to follow this advice may result in electrical shock

or death.

Health Hazard

•This appliance complies with electromagnetic safety

standards.

Hot Surface Hazard

•During use, accessible parts of this appliance will become

hot enough to cause burns.

•Do not let your body, clothing or any item other than

suitable cookware contact the ceramic glass until the

surface is cool.

•Metallic objects such as knives, forks, spoons and lids

should not be placed on the hob surface since they can get

hot.4

•Children less than 8 years of age shall be kept away unless

continuously supervised.

•Handles of saucepans may be hot to touch. Check saucepan

handles do not overhang other cooking zones that are on.

Keep handles out of reach of children.

•Failure to follow this advice could result in burns and

scalds.

Cut Hazard

•The razor-sharp blade of a cooktop scraper is exposed when

the safety cover is retracted. Use with extreme care and

always store safely and out of reach of children.

•Failure to use caution could result in injury or cuts.

Important safety instructions

•Never leave the appliance unattended when in use. Boilover

causes smoking and greasy spillovers that may ignite.

•Never use your appliance as a work or storage surface.

•Never leave any objects or utensils on the appliance.

•Never use your appliance for warming or heating the room.

•After use, always turn off the cooking zones and the

cooktop as described in this manual (i.e. by using the touch

controls). Do not rely on the pan detection feature to turn

off the cooking zones when You remove the pan.

•Do not allow children to play with the appliance or sit,

stand, or climb on it.

•Do not store items of interest to children in cabinets above

the appliance. Children climbing on the cooktop could be

seriously injured.

•Do not leave children alone or unattended in the area where

the appliance is in use.

•Children or persons with a disability which limits their

ability to use the appliance should have a responsible and

competent person to instruct them in its use. The instructor

should be satisfied that they can use the appliance without

danger to themselves or their surroundings.

•Do not repair or replace any part of the appliance unless

specifically recommended in the manual. All other

servicing should be done by a qualified technician.

•Do not use a steam cleaner to clean your cooktop.

•Do not place or drop heavy objects on your cooktop.

•Do not stand on your cooktop.

•Do not use pans with jagged edges or drag pans across the

glass surface as this can scratch the glass.

•Do not use scourers or any other harsh abrasive cleaning

agents to clean your cooktop, as these can scratch the

ceramic glass.

•If the supply cord is damaged, it must be replaced by the

manufacturer, its service agent or similarly qualified

persons in order to avoid a hazard.

•This appliance is intended to be used in a domestic

household environment only! Commercial use of any kind

is not covered under the manufacturer's warranty!

•WARNING: The appliance and its accessible parts become

hot during use. Young children should be kept away.

•Care should be taken to avoid touching heating elements.

•Children less than 8 years of age shall be kept away unless

continuously supervised.

•This appliance can be used by children aged from 8 years

and above and persons with reduced physical, sensory or

mental capabilities or lack of experience and knowledge if

they have been given supervision or instruction concerning

use of the appliance in a safe way and understand the

hazards involved.

•Children shall not play with the appliance. Cleaning and

user maintenance shall not be made by children without

supervision.

•WARNING: Unattended cooking on a hob with fat or oil

can be dangerous and may result in fire. NEVER try to

extinguish a fire with water, but switch off the appliance

and then cover flame e.g. with a lid or a fire blanket.

•WARNING: Danger of fire: do not store items on the

cooking surfaces.

•WARNING: If the surface is cracked, switch off the

appliance to avoid the possibility of electric shock, for hob

surfaces of glass-ceramic or similar material which protect

live parts.

•A steam cleaner is not to be used.

•The appliance is not intended to be operated by means of an

external timer or separate remote-control system.

•CAUTION: The cooking process has to be supervised. A

short term cooking process has to be supervised

continuously.

•Power cord can’t accessible after installation.

Product Overview

Top View

The Control Panel

Product Information

The ceramic/induction hob can meet different kinds of cuisine demands because of

resistance wire heating, micro-computerized control and multi-power selection, really

the optimal choice for modern families.

The hob centers on customers and adopts personalized design. The hob has safe and

reliable performances, making your life comfortable and enabling to fully enjoy the

pleasure from life.

1. 1800 W zone, boost to 2100 W

2. 1800 W zone, boost to 2100 W

3. 3000 W zone, boost to 3600 W

4. 3000 W zone, boost to 3600 W

5. Control panel

1. ON/OFF control 4. Pause/Keylock control

2. Power/Timer regulating key 5. Heating zone selection controls

3. Timer control 6. Boost control

A Word on Induction Cooking

Induction cooking is a safe, advanced, efficient, and economical cooking technology. It

works by electromagnetic vibrations generating heat directly in the pan, rather than

indirectly through heating the glass surface. The glass becomes hot only because the

pan eventually warms it up.

Before using your New Induction Hob

•Read this guide, taking special note of the ‘Safety Warnings’ section.

•Remove any protective film that may still be on your Induction hob.

Using the Touch Controls

•The controls respond to touch, so you don’t need to apply any pressure.

•Use the ball of your finger, not its tip.

•You will hear a beep each time a touch is registered.

•Make sure the controls are always clean, dry, and that there is no object (e.g. a

utensil or a cloth) covering them. Even a thin film of water may make the

controls difficult to operate.

iron pot

magnetic circuit

ceramic glass plate

induction coil

induced currents

Choosing the right Cookware

•Only use cookware with a base suitable for induction cooking. Look for the

induction symbol on the packaging or on the bottom of the pan.

•You can check whether your cookware is suitable by carrying out a magnet

test. Move a magnet towards the base of the pan. If it is attracted, the pan is

suitable for induction.

•If you do not have a magnet:

1. Put some water in the pan you want to check.

2. Follow the steps under ‘To start cooking’.

3. If does not flash in the display and the water is

heating, the pan is suitable.

•Cookware made by the following materials is not

suitable: pure stainless steel, aluminum or copper

without a magnetic base, glass, wood, porcelain, ceramic,

and earthenware.

Size of burner (mm)

The minimum cookware (diameter /mm)

160

120

180

140

210

160

280

180

Flexible zone

250

Do not use cookware with jagged edges or a curved base.

Make sure that the base of your pan is smooth, sits flat against the glass, and is the same

size as the cooking zone. Always centre your pan on the cooking zone.

Always lift pans off the ceramic hob – do not slide, or they may scratch the glass.

Use pans whose diameter of the ferromagnetic area (base of the pan) is in

the range of dimensions in the table below. (Table 1)

- If you use smaller pots, performance could be affected

- If you use pot with a diameter smaller than the one indicated in the table

above, pots may not be detected

According to the dimension of the zone you can use pots of different

diameters as picture below:

If the ferromagnetic part covers only partially the base of the pan, only the

ferromagnetic area will heat up, the rest of the base may not heat up a

sufficient temperature for cooking.

If the ferromagnetic area is not homogeneous, but presents others material

such as aluminum this may affect the heating up and the pan detection.

If the base of the pan is similar to the pictures below the pan could be not

detected.

Using your Induction Hob

To start cooking

•After power on, the buzzer beeps once, all the indicators light up for 1 second then

go out, indicating that the hob has entered the state of standby mode.

1. Touch the ON/OFF switch. all the indicators

show “– “

2. Place a suitable pan on the cooking zone that you

wish to use.

Make sure the bottom of the pan and the surface of

the cooking zone are clean and dry.

3. Touching the heating zone selection control, and an

indicator next to the key will flash

4. Select a heat setting by touching the “slider” control.

•If you don’t choose a heat setting within 1 minute,

the Induction hob will automatically switch off.

You will need to start again at step 1.

•You can modify the heat setting at any time during

cooking.

When you have finished cooking

1. Touching the heating zone selection that you wish to

switch off

2. Turn the cooking zone off by touching “slider”control

down to“0”. Make sure the display shows“0”.

3. Turn the whole cooktop off by touching the ON/OFF

control.

4. Beware of hot surfaces

“H” will show which means cooking zone is too hot to touch. It

will disappear when the surface has cooled down to a safe

temperature. It can also be used as an energy saving function if you

want to heat further pans, use the hotplate that is still hot.

Using the Power Management

It is possible to set a maximum power absorption level for the induction hob, choosing

up to different power ranges.

Induction hobs are able to limit themselves automatically in order to work at lower

power level, to avoid the risk of overloading.

To enter the power management function

Turn on the hob, then press at the same time the timer control and key lock. The timer

indicator will show “P5” which means power level 5. The default mode is on 7.2Kw.

To switch to another level

Select a power level by touching the slider control. There are 5 power levels, from “P1”

to “P5”. The timer indicator will show one of them.

“P1”: the maximum power is 2.5 Kw.

“P2”: the maximum power is 3.5 Kw.

“P3”: the maximum power is 4.5 Kw.

“P4”: the maximum power is 5.5 Kw.

“P5”: the maximum power is 7.2 Kw (the maximum power is 6.6 Kw for CI633SCBB).

Confirmation and Exit Power Management Function

Press at the same time the timer control and key lock for confirmation, then the hob will

be turned off.

Using Boost function

Activate the boost function

1. Select the zone with boost function (front left zone).

Note: The power setting of bridge zone works the same as any

other normal area.

2. Touch the booster key when the display is blinking,

power level indication shows “P”.

Cancel Boost function

1. Select the zone with boost function (front left zone).

2. Touching the “slider” to cancel the Boost function, and

select the level you want to set.

• Boost function can only last for 5 minutes, after that the zone will go to level 9

automatically.

Using the Pause function

1. Press the Pause control, the heating zones stop working. All the zone

indication show“||”

2. Press the Pause control once again, all the heating zones will revert to its

original setting.

The function is available when one or more heating zones are working.

If you don`t cancel the stop working mode within 30 minutes, the induction

cooktop will automatically switch off.

Locking the Controls

•You can lock the controls to prevent unintended use (for example children

accidentally turning the cooking zones on).

•When the controls are locked, all the controls except the ON/OFF control are

disabled.

To lock the controls

Touch the keylock control for 2 seconds. The timer indicator will show

“Lo “.

To unlock the controls

1. Make sure the hob is turned on.

2. Touch and hold the keylock control for 2 seconds.

3. You can now start using your hob.

When the hob is in lock mode, all the controls are disable except the ON/OFF,

you can always turn the hob off with the ON/OFF control in an emergency, but

you shall unlock the hob first in the next operation.

Residual Heat Warning

When the hob has been operating for some time, there will be some

residual heat. The letter “H” appears to warn you to keep away from it.

Using Bridge zone function

This may be used as a single zone or two individual zones depending on the

cooking needs in each situation.

It is made of two independent coils that can be controlled separately. When the

bridge zone is working, only the zone covered by the cookware is activated. This

function only works on 1# and 2# cooking zones.

To ensure that the cookware is detected and heat is distributed evenly, correctly

centre the cookware.

One hob with more than one flexible zone, it is not recommended to use several

zones at the same time for a single pan.

Activate Bridge zone function

1. To activate the bridge area as a single big zone, press the

front left zone key and rear left zone key at the same time.

2. The buzzer beeps indicating that the induction hob enters

selection of Bridge zone, and the corresponding indicator will flash.

3. Select the power level you want to set by touch “Slider”control.

Cancel Bridge zone function

1. Touching one of the bridge zone to cancel the bright zone function.

2. The power setting works the same as any other normal area.

Auto Shutdown

Safety feature of the hob is auto shut down. This occurs whenever you forget to switch

off a cooking zone. The default shutdown times are shown in the table below:

Power level

Default working timer (hour)

Using the Timer

You can use the timer in two different ways:

You can use it as a minute minder. In this case, the timer will not turn any cooking

zone off when the set time is up.

You can use it as cut-off timer to turn one or more cooking zones off after time is

up.

You can set the timer up to 99 minutes.

Using the Timer as a Minute Minder

If you are not selecting any cooking zone

1. Make sure the hob is turned on. And zone selection key is not activated (zone

indication ‘-‘ is not blinking).

Note: you can use the minute minder even if you are not selecting any cooking zone.

2. Touch timer control, “10” will show in the timer display

and “0” will flashes.

3. Set the time by touching the slider control of the

timer (e.g.5).

4. Touch timer control again, the “1” will flash.

5. Set the time by touching the slider control (e.g.9),

now the time you set is 95 minutes.

6. When the time is set, it will begin to count down

immediately. The display will show the remaining time.

7. Buzzer will bips for 30 seconds and the timer indicator

shows“-- “ when the setting time finished.

Using the timer to switch off one or more cooking zones

1. Touching the heating zone selection control that you want

to set the timer for.

2. Touch timer control, “10” will show in the timer display

and “0” will flashes.

3. Set the time by touching the slider control of the

timer (e.g.5).

4. Touch timer control again, the “1” will flash.

5. Set the time by touching the slider control (e.g.9),

now the time you set is 95 minutes.

6. When the time is set, it will begin to count down immediately.

The display will show the remaining time.

NOTE: There will be a red dot in the right bottom corner of

power level indication which indicating that zone is selected.

7. When cooking timer expires, the corresponding cooking

zone will switch off automatically.

Note: Other cooking zones will keep operating if they are turned on previously.

If the timer is set on more than one zone:

1. When you set timer for several cooking zones, red dots of the relevant cooking

zones are indicated. The timer display shows the min. timer. The dot of the

corresponding zone blinks.

(set to 15 minutes)

(set to 45 minutes)

2. Once the countdown timer expires, the corresponding zone will switch off. Then it

will show the new min. timer and the dot of corresponding zone will flash.

Note: Touch the heating zone selection control, the corresponding timer will be shown

in the timer indicator.

Cooking Guidelines

Take care when frying as the oil and fat heat up very quickly, particularly if you’re

using Boost. At extremely high temperatures oil and fat will ignite spontaneously

and this presents a serious fire risk.

Cooking Tips

•When food comes to the boil, reduce the power setting.

•Using a lid will reduce cooking times and save energy by retaining the heat.

•Minimise the amount of liquid or fat to reduce cooking times.

•Start cooking on a high setting and reduce the setting when the food has heated

through.

Simmering, cooking rice

•Simmering occurs below boiling point, at around 85˚C, when bubbles are just rising

occasionally to the surface of the cooking liquid. It is the key to delicious soups and

tender stews because the flavours develop without overcooking the food. You

should also cook egg-based and flourthickened sauces below boiling point.

•Some tasks, including cooking rice by the absorption method, may require a setting

higher than the lowest setting to ensure the food is cooked properly in the time

recommended.

Searing steak

To cook juicy flavoursome steaks:

1. Stand the meat at room temperature for about 20 minutes before cooking.

2. Heat up a heavy-based frying pan.

3. Brush both sides of the steak with oil. Drizzle a small amount of oil into the hot pan

and then lower the meat onto the hot pan.

4. Turn the steak only once during cooking. The exact cooking time will depend on the

thickness of the steak and how cooked you want it. Times may vary from about 2 – 8

minutes per side. Press the steak to gauge how cooked it is – the firmer it feels the

more ‘well done’ it will be.

5. Leave the steak to rest on a warm plate for a few minutes to allow it to relax and

become tender before serving.

For stir-frying

1. Choose a ceramic compatible flat-based wok or a large frying pan.

2. Have all the ingredients and equipment ready. Stir-frying should be quick. If cooking

large quantities, cook the food in several smaller batches.

3. Preheat the pan briefly and add two tablespoons of oil.

4. Cook any meat first, put it aside and keep warm.

5. Stir-fry the vegetables. When they are hot but still crisp, turn the cooking zone to a

lower setting, return the meat to the pan and add your sauce.

6. Stir the ingredients gently to make sure they are heated through.

7. Serve immediately.

Heat Settings

Heat setting

Suitability

1 - 2

• delicate warming for small amounts of food

• melting chocolate, butter, and foods that burn quickly

• gentle simmering

• slow warming

3 - 4

• reheating

• rapid simmering

• cooking rice

5 - 6

• pancakes

7 - 8

• sauteing

• cooking pasta

• stir-frying

• searing

• bringing soup to the boil

• boiling water

La page charge ...

Candy CTP634SCBB Manuel utilisateur

Marque: Candy

Modèle: CTP634SCBB

Catégorie: Plaques de cuisson

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Candy CTP634SCBB User manual

Documents connexes

Candy CFI 82 Le manuel du propriétaire

Candy CTP634SCBB Manuel utilisateur

Candy CTP634SCBB Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents