Makita VC001GL Manuel utilisateur

Marque: Makita

Modèle: VC001GL

Catégorie: Outils électroportatifs

Taper: Manuel utilisateur

INSTRUCTION MANUAL

MANUEL D'INSTRUCTION

MANUAL DE INSTRUCCIONES

Cordless Vacuum Cleaner

Aspirateur Sans Fil

Aspiradora Inalámbrica

VC001GL

VC003GL

IMPORTANT: Read Before Using.

IMPORTANT : Lire avant usage.

IMPORTANTE: Lea antes de usar.

2ENGLISH

ENGLISH (Original instructions)

SPECIFICATIONS

Model: VC001GL VC003GL

Standard lter type Cloth lter (for dry and wet dust)

Maximum air volume (with BL4040, ø32 mm (1-1/4") x 1.7 m (67") hose)

2.7 m3/min (95.35 cu.ft/min)

Vacuum (with BL4040, ø32 mm (1-1/4") x 1.7 m (67") hose) 23 kPa

Recoverable capacity Dust 8 L (2.1 gal.) 15 L (4 gal.)

Water 6 L (1.6 gal.) 12 L (3.2 gal.)

Dimensions (L x W x H) 366 mm x 334 mm x 425 mm

(14-3/8″ x 13-1/8″ x 16-3/4″)

366 mm x 334 mm x 475 mm

(14-3/8″ x 13-1/8″ x 18-3/4″)

Rated voltage D.C. 36 V - 40 V max

Net weight 8.1 - 10.0 kg (17.9 - 22.0 lbs) 8.4 - 10.3 kg (18.5 - 22.7 lbs)

• Due to our continuing program of research and development, the specications herein are subject to change

without notice.

• Specications and battery cartridge may dier from country to country.

• The weight does not include accessories but battery cartridge(s). The lightest and heaviest combination weight

of the appliance and battery cartridge(s) are shown in the table.

• For wet dust, the oat and the water lter or cloth lter are required.

Applicable battery cartridge and charger

Battery cartridge BL4020 / BL4025 / BL4040* / BL4050F*

* : Recommended battery

Charger DC40RA / DC40RB / DC40RC

• Some of the battery cartridges and chargers listed above may not be available depending on your region of

residence.

WARNING: Only use the battery cartridges and chargers listed above. Use of any other battery cartridges

and chargers may cause injury and/or re.

SAFETY WARNINGS

IMPORTANT

SAFETY

INSTRUCTIONS

When using an electrical appliance,

basic precautions should always be fol-

lowed, including the following:

READ ALL

INSTRUCTIONS

BEFORE USING

THIS APPLIANCE.

WARNING

To reduce the risk of re, electric shock

or injury:

1. Do not leave appliance when battery

tted. Remove battery from appli-

ance when not in use and before

servicing.

Do not expose to rain. Store indoors.

3. Do not allow to be used as a toy.

Close attention is necessary when

used by or near children.

4. Use only as described in this man-

ual. Use only manufacturer's recom-

mended attachments.

5. Do not use with damaged battery.

If appliance is not working as it

should, has been dropped, dam-

aged, left outdoors, or dropped into

water, return it to a service center.

3ENGLISH

6. Do not handle battery or appliance

with wet hands.

Do not put any object into openings.

Do not use with any opening blocked;

keep free of dust, lint, hair, and any-

thing that may reduce air ow.

8. Keep hair, loose clothing, ngers,

and all parts of body away from

openings and moving parts.

9. Turn o all controls before removing

the battery cartridge.

10. Use extra care when cleaning on

stairs.

11. Do not use to pick up ammable or

combustible liquids, such as gaso-

line, or use in areas where they may

be present.

12. Use only the charger supplied by

the manufacturer to recharge.

13. Do not pick up anything that is burn-

ing or smoking, such as cigarettes,

matches, or hot ashes.

14. Always make sure that lters are

correctly installed before use. Do

not use the cleaner without lters

in place. Replace a damaged lter

immediately. It is recommended to

have some spares as lters are con-

sumable items.

15. Do not charge the battery outdoors.

16. Always install oat before any wet

pick-up operation.

17.

Do not use the cleaner as a stool or

work bench. The machine may fall

down and may result in personal injury.

18. Do not vacuum the following:

• Flammable liquid (kerosene,

gasoline, solvents such as ben-

zine, thinner, etc.)

• Hot substances that are burn-

ing or smoking (cigarettes,

matches, incense sticks, can-

dles, hot ashes), sparks and

metal dust generated by cutting

or grinding metal, etc.

• Flammable material (toner,

paint, spray, etc.)

• Foam like carpet cleaning agent,

etc. (they may cause explosion

or re)

• Explosive or pyrophoric sub-

stances (nitroglycerin, alumi-

num, magnesium, titanium, zinc,

red phosphorus, yellow phos-

phorus, celluloid, etc. and their

dust, gas or steam)

• Sharp objects (glass, cutlery,

wood splinter, metal, stone, nail,

razor, push pin, etc.)

•

Solidifying and conductive ne

powder (metal or carbon powder)

• Dehumidier

• Large amount of powder (our,

re extinguisher powder, etc.)

• Substances that cause toxic

symptoms

• Aggressive chemicals (acid,

leach, etc.)

• Liquid or damp garbage, includ-

ing vomit and excreta

• Asbestos

• Pesticides

Such action may cause re, injury

and/or property damage.

To reduce your exposure to these

chemicals, always wear approved

respiratory protection such as dust

masks that are specially designed

to lter out microscopic particles.

Direct the exhaust air away from

your face and body.

NOTE: Read the OSHA regulation

on silica dust to understand the

requirements needed to reduce

exposure to silica dust at the job-

site. Specic rules apply to the drill-

ing, demolition cutting and grinding

materials that contain silica. All

OSHA requirements regarding

reducing silica dust can be found at

the OSHA website: www.osha.gov.

Battery tool use and care

1. Prevent unintentional starting.

Ensure the switch is in the o-po-

sition before connecting to battery

pack, picking up or carrying the

appliance. Carrying the appliance with

your nger on the switch or energiz-

ing appliance that have the switch on

invites accidents.

4ENGLISH

2. Disconnect the battery pack from

the appliance before making any

adjustments, changing accessories,

or storing appliance. Such preventive

safety measures reduce the risk of

starting the appliance accidentally.

3. Recharge only with the charger

specied by the manufacturer. A

charger that is suitable for one type of

battery pack may create a risk of re

when used with another battery pack.

4. Use appliances only with speci-

cally designated battery packs. Use

of any other battery packs may create

a risk of injury and re.

5. When battery pack is not in use,

keep it away from other metal

objects, like paper clips, coins,

keys, nails, screws or other small

metal objects, that can make a

connection from one terminal to

another. Shorting the battery terminals

together may cause burns or a re.

6. Under abusive conditions, liquid

may be ejected from the battery;

avoid contact. If contact acciden-

tally occurs, ush with water. If liq-

uid contacts eyes, additionally seek

medical help. Liquid ejected from the

battery may cause irritation or burns.

Do not use a battery pack or appli-

ance that is damaged or modied.

Damaged or modied batteries may

exhibit unpredictable behavior result-

ing in re, explosion or risk of injury.

Do not expose a battery pack or appli-

ance to re or excessive temperature.

Exposure to re or temperature above

130 °C may cause explosion.

9. Follow all charging instructions

and do not charge the battery

pack or appliance outside of the

temperature range specied in the

instructions. Charging improperly or

at temperatures outside of the speci-

ed range may damage the battery and

increase the risk of re.

10.

Have servicing performed by a quali-

ed repair person using only identical

replacement parts. This will ensure that

the safety of the product is maintained.

11. Do not modify or attempt to repair

the appliance or the battery pack

except as indicated in the instruc-

tions for use and care.

SAVE THESE

INSTRUCTIONS.

This appliance is intended for commer-

cial use.

Symbols

The followings show the symbols used for

tool.

volts

direct current

Take particular care and

attention.

Never stand on the cleaner.

Important safety

instructions for

battery cartridge

1. Before using battery cartridge,

read all instructions and cautionary

markings on (1) battery charger,

(2) battery, and (3) product using

battery.

2. Do not disassemble or tamper the

battery cartridge. It may result in a

re, excessive heat, or explosion.

3. If operating time has become

excessively shorter, stop operating

immediately. It may result in a risk

of overheating, possible burns and

even an explosion.

4. If electrolyte gets into your eyes,

rinse them out with clear water and

seek medical attention right away. It

may result in loss of your eyesight.

5. Do not short the battery cartridge:

(1) Do not touch the terminals with

any conductive material.

5ENGLISH

(2) Avoid storing battery cartridge

in a container with other metal

objects such as nails, coins, etc.

(3) Do not expose battery cartridge

to water or rain.

A battery short can cause a large

current ow, overheating, possible

burns and even a breakdown.

6. Do not store and use the tool and

battery cartridge in locations where

the temperature may reach or

exceed 50 °C (122 °F).

7. Do not incinerate the battery car-

tridge even if it is severely damaged

or is completely worn out. The bat-

tery cartridge can explode in a re.

8. Do not nail, cut, crush, throw, drop

the battery cartridge, or hit against a

hard object to the battery cartridge.

Such conduct may result in a re,

excessive heat, or explosion.

9. Do not use a damaged battery.

10. The contained lithium-ion batteries

are subject to the Dangerous Goods

Legislation requirements.

For commercial transports e.g. by

third parties, forwarding agents,

special requirement on packaging

and labeling must be observed.

For preparation of the item being

shipped, consulting an expert for

hazardous material is required.

Please also observe possibly more

detailed national regulations.

Tape or mask o open contacts and

pack up the battery in such a man-

ner that it cannot move around in

the packaging.

11. When disposing the battery car-

tridge, remove it from the tool and

dispose of it in a safe place. Follow

your local regulations relating to

disposal of battery.

12. Use the batteries only with the prod-

ucts specied by Makita. Installing

the batteries to non-compliant products

may result in a re, excessive heat,

explosion, or leak of electrolyte.

13. If the tool is not used for a long

period of time, the battery must be

removed from the tool.

14. During and after use, the battery

cartridge may take on heat which

can cause burns or low temperature

burns. Pay attention to the handling

of hot battery cartridges.

15. Do not touch the terminal of the tool

immediately after use as it may get

hot enough to cause burns.

16. Do not allow chips, dust, or soil

stuck into the terminals, holes, and

grooves of the battery cartridge.

It may result in poor performance

or breakdown of the tool or battery

cartridge.

17. Unless the tool supports the use

near high-voltage electrical power

lines, do not use the battery car-

tridge near a high-voltage electrical

power lines. It may result in a mal-

function or breakdown of the tool or

battery cartridge.

18. Keep the battery away from

children.

SAVE THESE

INSTRUCTIONS.

CAUTION: Only use genuine Makita batteries.

Use of non-genuine Makita batteries, or batteries that

have been altered, may result in the battery bursting

causing res, personal injury and damage. It will

also void the Makita warranty for the Makita tool and

charger.

Tips for maintaining maximum

battery life

1. Charge the battery cartridge before completely

discharged. Always stop tool operation and

charge the battery cartridge when you notice

less tool power.

2. Never recharge a fully charged battery car-

tridge. Overcharging shortens the battery

service life.

3. Charge the battery cartridge with room tem-

perature at 10 °C - 40 °C (50 °F - 104 °F). Let

a hot battery cartridge cool down before

charging it.

4. When not using the battery cartridge, remove

it from the tool or the charger.

5. Charge the battery cartridge if you do not use

it for a long period (more than six months).

6ENGLISH

PARTS DESCRIPTION

Fig.1

► 1. Head unit 2. Float 3. Float cage 4. Cloth lter

5. Tank

FUNCTIONAL

DESCRIPTION

CAUTION: Always be sure that the appliance

is switched o and the battery cartridges are

removed before adjusting or checking function on

the appliance.

Installing or removing battery

cartridge

CAUTION: Always switch o the appliance

before installing or removing battery cartridges.

CAUTION: Hold the cleaner and battery car-

tridges rmly when installing or removing battery

cartridges. Failure to do so may cause them to slip

o your hands, resulting in damage to the cleaner and

battery cartridges or personal injury.

CAUTION: Be careful not to pinch your n-

gers when opening or closing the battery cover.

Failure to do so may cause personal injury.

The cleaner has double battery slots. With two identical

batteries in parallel, you can extend your running time

in one or more uses without having to stop to recharge

batteries. The cleaner also works with a single battery,

so you can choose with either double batteries or single

battery according to your needs.

Fig.2

► 1. Left battery slot 2. Right battery slot

With double batteries

Continuous drive with two batteries allows longer run-

time and more ecient cleaning. When the rst battery

is becoming empty, the cleaner automatically switches

a power source, so it continues working with the second

battery.

NOTE: The left battery slot (when facing the front of

the cleaner) has priority over the right battery slot.

The right battery slot will only be identied as a power

source, either when no battery is installed in the

left battery slot or the battery in the left battery slot

becomes empty.

NOTE: You can remove the battery from the left

battery slot and recharge it after the cleaner has

switched its power source from the left battery slot to

the right without ceasing operation. To give priority

back to the left battery slot after installing a recharged

battery, restart the cleaner.

With a single battery

Only one battery is required as a power source in either

the left or right battery slot. The cleaner automatically

determines which battery slot is available according to

operating conditions.

Installation and uninstallation

To install battery cartridges, release the lock rst, and

open the battery cover. Then insert the battery cartridges.

Fig.3

► 1. Lock 2. Battery cover

7ENGLISH

Align the tongues on the battery cartridges with the

grooves in the battery housing and slip them into place.

Insert them all the way until they lock in place with a

little click.

Then lock the battery cover.

Fig.4

► 1. Battery cartridge 2. Button

To remove the battery cartridges, slide them out of the

battery housing while pressing and holding the buttons

in front of the cartridges.

CAUTION: Always install the battery cartridge

fully. If not, it may accidentally fall out of the appli-

ance, causing injury to you or someone around you.

CAUTION: Do not install the battery cartridge

forcibly. If the cartridge does not slide in easily, it is

not being inserted correctly.

NOTE: When the cleaner switches the power source

from the rst battery to the second, it may require a

temporary halt in operations, causing a slight loss of

suction. Please note that it is not malfunction so the

cleaner recovers and resumes operations immedi-

ately after the pause.

Indicating the remaining battery

capacity

Press the check button on the battery cartridge to indi-

cate the remaining battery capacity. The indicator lamps

light up for a few seconds.

Fig.5

► 1. Indicator lamps 2. Check button

Indicator lamps Remaining

capacity

Lighted O Blinking

75% to 100%

50% to 75%

25% to 50%

0% to 25%

Charge the

battery.

The battery

may have

malfunctioned.

NOTE: Depending on the conditions of use and the

ambient temperature, the indication may dier slightly

from the actual capacity.

NOTE: The rst (far left) indicator lamp will blink when

the battery protection system works.

Battery indicators on control panel

The remaining battery capacity can be read on the

control panel at any time. Press the check button, and

the left and right indicators will show the battery charge

levels correspondingly.

Fig.6

► 1. Battery indicators 2. Check button

8ENGLISH

Fig.7

Battery indicator status Remaining

battery

capacity

On O Blinking

50% to 100%

20% to 50%

0% to 20%

Charge the

battery

Battery not

inserted

NOTE: The battery indicators will also be activated

when the cleaner starts functioning or switches its

power source from one to another.

Appliance / battery protection

system

The appliance is equipped with an appliance/battery

protection system. This system automatically cuts o

power to the motor to extend appliance and battery life.

The appliance will automatically stop during operation

if the appliance or battery is placed under one of the

following conditions:

Overload protection

When the appliance/battery is operated in a manner

that causes it to draw an abnormally high current, the

appliance automatically stops. In this situation, turn the

appliance o and stop the application that caused the

appliance to become overloaded. Then turn the appli-

ance on to restart.

Overheat protection

On Blinking

When the appliance is overheated, the appliance stops

automatically, and both left and right battery indicators

blink. In this situation, let the appliance cool down

before turning the appliance on again.

On Blinking

When the battery is overheated, the appliance stops

automatically, and one of the indicators for overheated

battery blinks. In this situation, let the battery cool down

before turning the appliance on again.

Overdischarge protection

When the battery capacity becomes low, the appliance

stops automatically. If the appliance does not run along

with the switch operation, remove the batteries from the

appliance and recharge them.

Protections against other causes

Protection system is also designed for other causes that

could damage the appliance and allows the appliance to

stop automatically. Take all the following steps to clear

the causes, when the appliance has been brought to a

temporary halt or stop in operation.

1. Turn the appliance o, and then turn it on again to

restart.

2. Charge the battery(ies) or replace it/them with

recharged battery(ies).

3. Let the appliance and battery(ies) cool down.

If no improvement can be found by restoring protection

system, then contact your local Makita Service Center.

Switch action

Turning cleaner on

1. Turn the stand-by switch in the "I" (ON) position to

have the cleaner ready in stand-by mode.

2. Press the power button.

To switch back to stand-by mode, press the power

button again.

Turning cleaner o

Perform one of the following steps.

• Press the power button to set the cleaner back in

stand-by mode, and then turn the stand-by switch

in the "O" (OFF) position.

• Turn the stand-by switch in the "O" (OFF) position.

9ENGLISH

Adjusting suction power

The suction power can be adjusted according to your

work needs.

• Turn the suction force adjusting knob to the left to

reduce the suction power.

• Turn the suction force adjusting knob to the right

to increase the suction power.

Fig.8

► 1. Stand-by switch 2. Power button 3. Suction force

adjusting knob

Auto-suction stop during wet

suction operation

WARNING: Do not use for a long time while

the oat is at work. Using the cleaner with its oat at

work for a long time can cause overheat, resulting in

the cleaner deformation.

WARNING: Do not pick up foam or soapy

liquid. It can cause foam to come out of air exit

before the oat works. Continuous use under such

conditions may cause an electric shock and breakage

of the cleaner.

The auto-suction stop feature works only while the

cleaner is used with the oat and oat cage.

The cleaner has a oat mechanism that prevents water

from entering into the motor when picking up more than

a certain amount of water. When the tank is full and the

cleaner no longer picks up water, switch o the cleaner

and empty the tank.

Locking and unlocking casters

Rear casters can be locked with stoppers to help the

cleaner stand still.

Lower the stopper lever by hand to lock the caster, and

raise it up to release.

Fig.9

► 1. Caster 2. Stopper lever 3. Unlocked position

4. Locked position

NOTE: When moving the cleaner, make sure that the

caster is unlocked. Moving the cleaner with the caster

in a locked position may cause damage to the caster.

Carriage handle

CAUTION: Lift and carry the appliance with

due care. Failing to do so may result in personal

injury or damage to the appliance.

When carrying the cleaner, carry it by holding the han-

dle on the head unit. The handle is retractable on the

head unit when not in use.

Fig.10

10 ENGLISH

ASSEMBLY

CAUTION: Always be sure that the appliance

is switched o and the battery cartridges are

removed before carrying out any work on the

appliance.

CAUTION: Always wear dust mask during

assembly or maintenance.

Installing powder lter (HEPA) and

prelter (for dry dust)

Optional accessory

CAUTION: Never pick up water or other liq-

uids or wet dusts when using the powder lter.

Picking up such things may cause the powder lter

breakage.

To use powder lter:

1. Loosen the screws securing the oat cage, and

then remove the screws, oat cage and oat from the

head unit.

Fig.11

► 1. Screw 2. Float cage 3. Float 4. Head unit

2. Remove the cloth lter out of the tank.

Fig.12

► 1. Cloth lter 2. Tank

3. Place the prelter into the tank aligning the mount-

ing position markings on the prelter and tank.

4. Set the damper into the prelter, and then place

the powder lter over the damper aligning the mounting

position markings on the powder lter and prelter.

5. Mount the head unit over the tank and secure

them with the locking latches.

Fig.13

► 1. Head unit 2. Powder lter (HEPA) 3. Damper

4. Prelter 5. Tank 6. Mounting position marking

NOTICE: Before using the powder lter, make

sure that prelter and damper are used together. It

is not allowed to install powder lter alone.

Installing water lter

Optional accessory

NOTICE: Never pick up water or wet dust without

the oat and the cloth lter or the water lter.

NOTICE: For picking up wet dust, make sure that

the oat cage and the oat are installed on the

cleaner.

NOTICE: When installing the water lter on the

tank, set it tight at the opening of the tank so

that the hook of the water lter engages the tank

opening rmly and there is no space between the

water lter and the tank.

11 ENGLISH

To pick up water or wet dust only, the water lter is more

suitable than the cloth lter.

When installing the water lter, align its mounting posi-

tion marking with the one on the tank.

Fig.14

► 1. Water lter 2. Tank 3. Mounting position marking

NOTE: It is recommended using water lter when

picking up large amount of water repeatedly.

Otherwise vacuum ability may be reduced in case of

cloth lter.

Installing paper pack

Optional accessory

WARNING: Before using a paper pack,

make sure that the cloth lter or prelter is used

together. Failure to use the cloth lter / prelter

together may cause unusual noise and heat, resulting

in a re.

NOTICE: Never pick up water or other liquids

or wet dusts when using a paper pack. Picking up

such things may cause the paper pack breakage.

NOTICE: When using the cloth lter, make sure

that the oat and the oat cage are attached on

the head unit.

NOTICE: When using the prelter, make sure

that the powder lter and the damper are used

together.

1. Unfold a paper pack.

2. Align the paper pack opening with the dust intake

of the tank.

3. Install the paper pack into the tank with its card-

board opening hooked on the paper pack holder.

Fig.15

► 1. Paper pack 2. Cardboard opening 3. Paper pack

holder 4. Dust intake

Installing polyethylene bag

With a polyethylene bag installed in the tank, you can

easily empty the tank without letting your hands dirty.

Lay a polyethylene bag over the tank, and slip one side

of the top edge of the bag at its open end in between

the holder plate and the front wall of the tank.

Fig.16

► 1. Holder plate 2. Front wall of tank 3. Polyethylene

bag

12 ENGLISH

Spread the other top edges of the bag outwards over

the top rims of the tank. Place the cloth lter or prelter

over the polyethylene bag to fasten the opening of the

bag securely.

Fig.17

► 1. Cloth lter / prelter

NOTE:

A polyethylene bag available on the market

can be used. 0.04 mm or thicker one is recommended.

NOTE:

Too much dust will tear the bag easily, so do not

collect the dust more than the half of the bag capacity.

Emptying tank with polyethylene bag

WARNING:

Always make sure that the cleaner

is switched o and the battery cartridges are

removed before emptying the tank. Failure to do so

may cause an electric shock and serious personal injury.

NOTICE: Do not apply a great impact on the oat

cage and tank. Applying a great impact may cause

deformation and damage to the parts.

NOTICE: Empty the tank at least once a day

although this depends on picked-up dust volume

in the tank. Or, the suction force will weaken and the

motor may be broken.

NOTICE: Do not grab the hooks or latches when

emptying the tank. Grabbing the hooks or latches

may cause them to break.

Release the locking latches and lift the head unit up o the tank.

Shake o dust from the cloth lter or prelter before

lifting the lter away from the tank.

Then remove the polyethylene bag out of the tank,

closing the opening of the bag by hand.

Fig.18

► 1. Polyethylene bag 2. Tank

NOTE: Take the polyethylene bag out of the tank

carefully to avoid it from being scratched and torn by

the edges inside the tank.

NOTE: Empty the polyethylene bag before it

becomes full. Too much dust in the tank may cause

the polyethylene bag to be torn.

Installing multi hook

Use the multi hook to hold a hose, accessories and

attachments not in use in place, and you can quickly

take them out according to your preferences.

Fig.19

Place the multi hook over the mounting base at the rear

of the cleaner, setting the rails on the multi hook along

the grooves on the mounting base.

Fig.20

► 1. Multi hook 2. Mounting base

13 ENGLISH

Installing MAKPAC adapter

Optional accessory

Connectable and stackable MAKPAC storage cases

can be installed on top of the cleaner with an optional

adapter. The cases are available in many sizes and

styles to suit your preferences.

Place the mounting base hook over the handle of the

cleaner with its mounting surface facing upwards when

the handle is folded into the closed position.

Fig.21

► 1. Mounting base hook 2. Mounting surface

3. Handle

Mount the MAKPAC adapter onto the mounting base hook,

and secure them together with four screws provided.

Fig.22

► 1. MAKPAC adapter 2. Mounting base hook

3. Screw

Lift the push bar up and tighten the knob to prepare

installing the MAKPAC cases onto the cleaner.

Fig.23

► 1. Push bar 2. Knob

NOTE: For details on installing the MAKPAC cases,

refer to the instructions provided with the MAKPAC

adapter and cases.

Installing hose

NOTICE: Never force the hose for bending or

stamp it. Never move the cleaner by pulling the

hose. Forcing, stamping and pulling the hose may

cause a breakage or deformation of the hose.

NOTICE: When picking up large wastes such as

planer carvings, concrete dusts or similar other

than small wastes, use the 38 mm inner diameter

hose (optional accessory). Using the 28 mm inner

diameter hose (optional accessory) may cause a

hose stung and damage.

Connection to cleaner

Insert the hose end to the dust intake (hose inlet) of the

cleaner, then turn it clockwise until it locks in place.

Fig.24

► 1. Hose 2. Dust intake (hose inlet)

14 ENGLISH

Connections with your work tools

(Country specic)

By connecting the vacuum cleaner to any available

work tools compatible with the cleaner, it works as a

dust extractor for your power tools.

Select one of the front cus or joints (optional acces-

sories) as most suitable for your tool model. Place the

cus or joint, as necessary, between the front end of the

cleaner hose and a dust extraction port of your tool.

Fig.25

► 1. Front cus or joint 2. Cleaner hose 3. Power tool

4. Vacuum cleaner

Installing or removing cleaner

attachments

CAUTION: After installing an attachment,

check if it is securely installed. If the attachment

is installed imperfectly, it may come o and cause

personal injury.

Attachments without lock function

Optional accessory

Insert an attachment into the suction inlet of the cleaner

by pushing and hand screwing it in place.

Hand twist and pull the attachment apart from the suc-

tion inlet after use.

Fig.26

Attachments with lock function

Optional accessory

NOTICE: When installing the attachment with

lock function, be sure to align the release button

with the hook on the attachment. If they are not

aligned, the attachment will not be locked and may

come o from the cleaner.

Insert an attachment into the suction inlet of the cleaner

by pushing them together with a click.

To remove the attachment, pull it o while pushing the

release button.

Fig.27

► 1. Suction inlet with lock function 2. Release button

3. Attachment with lock function

NOTE: An attachment with lock function can only be

installed in the suction inlet with lock function.

Fig.28

► 1. Attachment with lock function 2. Suction inlet with

lock function 3. Suction inlet without lock function

15 ENGLISH

Adjusting lengths of slide-type

extension wand

Optional accessory

A slide-type extension wand can be combined for

shorter and longer lengths. It allows to clean hard-to-

reach areas and comfortable positioning options.

Pull in and out the slide pipe to change wand lengths

while pressing and holding the slide button.

Release the slide button to lock the slide pipe in your

desired position.

Fig.29

► 1. Slide pipe 2. Slide button

MAINTENANCE

CAUTION: Always be sure that the appliance

is switched o and the battery cartridges are

removed before attempting to perform inspection

or maintenance.

NOTICE: Never use gasoline, benzine, thinner,

alcohol or the like. Discoloration, deformation or

cracks may result.

To maintain product SAFETY and RELIABILITY,

repairs, any other maintenance or adjustment should

be performed by Makita Authorized or Factory Service

Centers, always using Makita replacement parts.

Storage of accessories

Accessories and attachments not in use, such as noz-

zles and brushes, can be hooked and stored in the multi

hook at the rear of the cleaner.

Fig.30

►

1. Multi hook 2. Accessories and attachments not in use

Pipes (with an optional stopper installed) can be placed into

the pipe holder when not using the cleaner for a short time.

Fig.31

► 1. Stopper (optional accessory) 2. Pipe holder

A hose can be wrapped and stored around the housing or han-

dle of the cleaner in large loops. Connect its both ends together

to make loops and hook the loops onto the handle raised up.

Alternatively, keep its root end installed in the hose inlet and

hang the loops on the multi hook with the loose end tied up.

Fig.32

16 ENGLISH

Fig.33

Cleaning of cloth lter

Clean out the cloth lter at regular intervals since

clogged cloth lter may result in poor suction

performance.

Wipe and shake dust o the cloth lter by hand on

occasions.

Fig.34

► 1. Cloth lter

Cleaning of powder lter (HEPA) and

prelter

Optional accessory

Clean out the powder lter, prelter and damper at

regular intervals since clogged lters and damper may

result in poor suction performance.

Routinely wipe and shake dust o lters and damper by hand.

Occasionally wash the powder lter in water, rinse and

dry thoroughly in the shade before use. Never wash

lters in a washing machine.

Fig.35

NOTE: Do not rub or scratch the powder lter, the

prelter and the damper with hard objects such as a

brush and a paddle.

NOTE: The lters wear out in course of time. It is

recommended to have some spares for them.

OPTIONAL

ACCESSORIES

CAUTION: These accessories or attachments

are recommended for use with your Makita tool

specied in this manual. The use of any other

accessories or attachments might present a risk of

injury to persons. Only use accessory or attachment

for its stated purpose.

If you need any assistance for more details regard-

ing these accessories, ask your local Makita Service

Center.

• Hose

• Front cus (22, 24, 38)

• Straight pipe

• Extension wand

• Corner nozzle

• Round brush

• Powder lter, HEPA (for dry dust)

• Damper

• Prelter

• Water lter

• Cloth lter

• Nozzle assembly

• Bent pipe

• Polyethylene bag

• Paper pack

• MAKPAC adapter

• Makita genuine battery and charger

NOTE: Some items in the list may be included in the

tool package as standard accessories. They may

dier from country to country.

MAKITA LIMITED WARRANTY

Please refer to the annexed warranty sheet for the

most current warranty terms applicable to this product.

If annexed warranty sheet is not available, refer to the

warranty details set forth at below website for your

respective country.

United States of America: www.makitatools.com

Canada: www.makita.ca

Other countries: www.makita.com

17 FRANÇAIS

FRANÇAIS (Mode d’emploi original)

SPÉCIFICATIONS

Modèle : VC001GL VC003GL

À ltre standard Filtre en tissu (pour poussières sèches et mouillées)

Volume d’air maximum (avec BL4040, tuyau de ø32 mm (1-1/4") x 1,7 m (67"))

2,7 m3/min (95,35 cu.ft/min)

Aspiration (avec BL4040, tuyau de ø32 mm (1-1/4") x 1,7 m (67")) 23 kPa

Capacité de récupération Poussières 8 L (2,1 gal.) 15 L (4 gal.)

Eau 6 L (1,6 gal.) 12 L (3,2 gal.)

Dimensions (L x P x H) 366 mm x 334 mm x 425 mm

(14-3/8″ x 13-1/8″ x 16-3/4″)

366 mm x 334 mm x 475 mm

(14-3/8″ x 13-1/8″ x 18-3/4″)

Tension nominale C.C. 36 V - 40 V max.

Poids net 8,1 - 10,0 kg (17,9 - 22,0 lbs) 8,4 - 10,3 kg (18,5 - 22,7 lbs)

• Étant donné l’évolution constante de notre programme de recherche et développement, les spécications

contenues dans ce manuel sont sujettes à modication sans préavis.

• Les spécications et la batterie peuvent varier suivant les pays.

• Le poids ne comprend pas les accessoires autres que la/les batterie(s). Les combinaisons la plus légère et la

plus lourde d’appareil et de batterie(s) sont indiquées dans le tableau.

• Pour les poussières mouillées, le otteur et le ltre à eau ou le ltre en tissu sont requis.

Batteries et chargeurs applicables

Batterie BL4020 / BL4025 / BL4040* / BL4050F*

* : Batterie recommandée

Chargeur DC40RA / DC40RB / DC40RC

• Suivant la région où vous habitez, il se peut que certaines des batteries et certains des chargeurs énumérés

ci-dessus ne soient pas disponibles.

MISE EN GARDE : Utilisez exclusivement les batteries et chargeurs énumérés ci-dessus. L’utilisation

de toute autre batterie ou tout autre chargeur peut entraîner une blessure et/ou un incendie.

CONSIGNES DE

SÉCURITÉ

IMPORTANTES

CONSIGNES DE

SÉCURITÉ

Lors de l’utilisation d’un appareil élec-

trique, vous devez toujours prendre

des précautions de base, dont les sui-

vantes :

CONSERVEZ CES

INSTRUCTIONS.

MISE EN GARDE

Pour réduire les risques d’incendie, de

décharge électrique et de blessure :

1. Ne quittez pas l’appareil alors que la

batterie y est insérée. Retirez la bat-

terie de l’appareil lorsqu’il n’est pas

utilisé et avant de le faire réparer.

2. Ne l’exposez pas à la pluie.

Rangez-le à l’intérieur.

3. Ne laissez pas les enfants l’utiliser

comme jouet. Une attention particu-

lière est nécessaire lors de l’utilisa-

tion par les enfants ou près d’eux.

4. Utilisez l’outil uniquement de la

façon décrite dans ce manuel.

Utilisez uniquement les accessoires

recommandés par le fabricant.

18 FRANÇAIS

5. Ne l’utilisez pas avec une batterie

endommagée. Si l’appareil ne fonc-

tionne pas bien, s’il a été échappé,

endommagé, laissé à l’extérieur ou

échappé dans l’eau, retournez-le à

un centre de service après-vente.

6. Ne manipulez pas la batterie ou l’ap-

pareil avec les mains mouillées.

7. Ne mettez rien dans les ouvertures.

N’utilisez jamais l’outil si une des

ouvertures est bouchée ; gardez ces

dernières exemptes de poussières,

charpies, cheveux ou tout objet pou-

vant réduire la circulation de l’air.

8. Gardez les cheveux, les vêtements

amples, les doigts et toute autre par-

tie du corps à l’écart des ouvertures

et des pièces en mouvement.

9. Mettez toutes les commandes hors

tension avant de retirer la batterie.

10. Soyez tout particulièrement pru-

dent lorsque vous nettoyez sur les

marches d’un escalier.

11. Ne l’utilisez pas pour aspirer des

liquides inammables ou com-

bustibles tels que l’essence, ou

dans des zones où de tels liquides

peuvent être présents.

12. Utilisez uniquement le chargeur

fourni par le fabricant pour rechar-

ger la batterie.

13. N’aspirez pas d’objets qui brûlent

ou dégagent de la fumée, tels que

des cigarettes, des allumettes ou

des cendres encore chaudes.

14. Assurez-vous toujours que les

ltres sont correctement installés

avant l’utilisation. N’utilisez pas l’as-

pirateur sans les ltres. Remplacez

immédiatement tout ltre endom-

magé. Il est recommandé de dis-

poser de ltres de rechange, car il

s’agit d’articles consommables.

15.

Ne chargez pas la batterie à l’extérieur.

16. Installez toujours le otteur avant

d’eectuer toute opération de col-

lecte de matières mouillées.

17. N’utilisez pas l’aspirateur en tant

que tabouret ou établi. La machine

risquerait de tomber et d’entraîner

une blessure.

18. N’utilisez pas l’appareil pour aspirer

les matières suivantes :

• Liquides inammables (kéro-

sène, essence, solvants tels que

benzine, diluant, etc.)

•

Substances chaudes qui brûlent

ou dégagent de la fumée (ciga-

rettes, allumettes, bâtons

d’encens, chandelles, cendres

chaudes), étincelles et poussières

métalliques générées par la coupe

ou le meulage du métal, etc.

•

Matières inammables (encre en poudre,

peinture, substance vaporisée, etc.)

•

Mousses telle qu’agent de nettoyage

pour tapis, etc. (elles peuvent causer

une explosion ou un incendie)

•

Substances explosives ou pyro-

phoriques (nitroglycérine, alumi-

nium, magnésium, titane, zinc,

phosphore rouge, phosphore

jaune, celluloïd, etc., et leurs

poussières, gaz ou vapeurs)

• Objets tranchants (verre, coutel-

lerie, éclat de bois, métal, pierre,

clou, rasoir, punaise, etc.)

•

Poudre ne solidiante et conductrice

(poudre de métal ou de carbone)

• Déshydrateur

• Grande quantité de poudre

(farine, poudre d’extincteur, etc.)

• Substances qui causent des

symptômes d’intoxication

• Produits chimiques corrosifs

(acide, lixiviat, etc.)

• Déchets liquides ou humides, y

compris vomi et excréments

• Amiante

• Pesticides

Ces applications peuvent causer

un incendie, une blessure et/ou des

dommages matériels.

Pour réduire le risque d’exposition à

ces produits chimiques, portez tou-

jours des dispositifs de protection

respiratoire approuvés, tels que des

masques antipoussières spéciale-

ment conçus pour ltrer les particules

microscopiques. Dirigez l’air évacué

loin de votre visage et de votre corps.

19 FRANÇAIS

NOTE : Lisez la réglementation

OSHA sur la poussière de silice

pour comprendre les exigences

nécessaires pour réduire l’expo-

sition à la poussière de silice sur

le lieu de travail. Des règles spéci-

ques s’appliquent aux matériaux

de perçage, de coupe de démolition

et de meulage qui contiennent de

la silice. Toutes les exigences de

l’OSHA concernant la réduction de

la poussière de silice sont dispo-

nibles sur le site web de l’OSHA :

www.osha.gov.

Utilisation et entretien des outils

alimentés par batterie

Évitez les démarrages accidentels.

Assurez-vous que l’interrupteur

est sur la position d’arrêt avant de

connecter la batterie, de ramas-

ser l’appareil ou de le transporter.

Transporter l’appareil avec le doigt sur

l’interrupteur, ou mettre l’appareil sous

tension avec l’interrupteur en position

de marche ouvre la porte aux accidents.

2. Déconnectez la batterie de l’appareil

avant d’eectuer tout réglage, de

remplacer les accessoires ou de

ranger l’appareil. De telles mesures

de prévention réduisent le risque de

démarrage accidentel de l’appareil.

3. Pour recharger, utilisez uniquement

le chargeur spécié par le fabricant.

L’utilisation d’un chargeur conçu pour

un type donné de bloc-piles comporte

un risque d’incendie lorsqu’il est utilisé

avec un autre type de bloc-piles.

4. Utilisez les appareils uniquement

avec les batteries spéciquement

désignées. L’utilisation de tout autre

bloc-piles peut entraîner un risque de

blessure et d’incendie.

Lorsque vous n’utilisez pas le bloc-

piles, rangez-le à l’écart des objets

métalliques tels que trombones,

pièces de monnaie, clés, clous, vis ou

autres petits objets métalliques qui

risqueraient d’établir une connexion

entre les bornes. La mise en court-cir-

cuit des bornes de batterie peut causer

des brûlures ou un incendie.

6. Dans des conditions d’utilisation

inadéquates de la batterie, il peut

y avoir fuite d’électrolyte; évitez

tout contact avec ce liquide. En

cas de contact accidentel, rincez

avec beaucoup d’eau. Si le liquide

pénètre dans vos yeux, il faut aussi

consulter un médecin. L’électrolyte

qui s’échappe de la batterie peut cau-

ser des irritations ou des brûlures.

7. N’utilisez pas une batterie ou un

appareil endommagé ou modié.

Les batteries endommagées ou

modiées peuvent se comporter de

manière imprévisible et entraîner

un incendie, une explosion ou un

risque de blessure.

8. N’exposez pas une batterie ou un

appareil au feu ou à une tempé-

rature excessive. L’exposition au

feu ou à une température supé-

rieure à 130 °C peut provoquer une

explosion.

9. Respectez toutes les instructions de

charge, et ne chargez pas la batte-

rie ou l’appareil hors de la plage de

température spéciée dans les ins-

tructions. Charger de manière inadé-

quate ou à des températures hors de

la plage spéciée peut endommager

la batterie et fait augmenter le risque

d’incendie.

10. Conez l’entretien à un réparateur

qualié et n’utilisant que des pièces

de rechange identiques aux pièces

d’origine. Cela assurera le maintien

du produit dans un état sécuritaire.

11. Ne modiez pas ou n’essayez pas

de réparer l’appareil ou la batterie

autrement que tel qu’indiqué dans

les instructions d’utilisation et

d’entretien.

CONSERVEZ CES

INSTRUCTIONS.

Cet appareil est conçu pour un usage

commercial.

20 FRANÇAIS

Symboles

Les symboles utilisés pour l’outil sont indi-

qués ci-dessous.

volts

courant continu

Soyez tout particulièrement

prudent et attentif.

Ne montez jamais sur

l’aspirateur.

Consignes de

sécurité importantes

pour la batterie

1. Avant d’utiliser la batterie, lisez

toutes les instructions et les mises

en garde apposées sur (1) le char-

geur de batterie, (2) la batterie et (3)

le produit utilisant la batterie.

Ne démontez pas et ne modiez pas la

batterie. Cela peut entraîner un incendie,

une chaleur excessive ou une explosion.

3. Cessez immédiatement l’utilisa-

tion si le temps de fonctionnement

devient excessivement court. Il y a

risque de surchaue, de brûlures,

voire d’explosion.

4. Si l’électrolyte pénètre dans vos

yeux, rincez-les à l’eau claire et

consultez immédiatement un méde-

cin. Il y a risque de perte de la vue.

5. Ne court-circuitez pas la batterie :

(1) Ne touchez les bornes avec

aucun matériau conducteur.

(2) Évitez de ranger la batterie dans

un conteneur avec d’autres

objets métalliques tels que

clous, pièces de monnaie, etc.

(3) Évitez d’exposer la batterie à

l’eau ou à la pluie.

Un court-circuit de la batterie pour-

rait provoquer un fort courant, une

surchaue, parfois des brûlures et

même une panne.

6. Ne rangez pas et n’utilisez pas

l’outil ou la batterie dans des empla-

cements où la température peut

atteindre ou dépasser 50 °C (122 °F).

7. Ne jetez pas la batterie au feu même

si elle est sérieusement endomma-

gée ou complètement épuisée. La

batterie peut exploser au contact du

feu.

8. Évitez de clouer, de couper, d’écra-

ser, de lancer ou d’échapper la

batterie, ou de heurter un objet dur

contre la batterie. Cela peut entraîner

un incendie, une chaleur excessive ou

une explosion.

9. N’utilisez pas une batterie si elle est

endommagée.

10. Les batteries lithium-ion fournies

sont soumises aux exigences de

la législation sur les marchandises

dangereuses.

Des exigences particulières sur

l’emballage et l’étiquetage doivent

être respectées lors du transport

commercial par des tiers, des transi-

taires, etc.

Pour préparer la marchandise à

expédier, consultez un expert en

matériaux dangereux si nécessaire.

Respectez aussi les éventuelles

réglementations nationales plus

détaillées.

Recouvrez de ruban isolant les

contacts exposés, et emballez la

batterie de sorte qu’elle ne puisse

pas se déplacer à l’intérieur de

l’emballage.

11. Lors de l’élimination de la batterie,

retirez-la de l’outil et éliminez-la

dans un endroit sûr. Respectez la

réglementation locale concernant

l’élimination de la batterie.

12. N’utilisez les batteries qu’avec

les produits spéciés par Makita.

Installer les batteries sur des produits

non conformes peut entraîner un

incendie, une chaleur excessive, une

explosion ou une fuite d’électrolyte.

13. Suivez la réglementation locale

concernant l’élimination de la

batterie.

La page charge ...

Makita VC001GL Manuel utilisateur

Marque: Makita

Modèle: VC001GL

Catégorie: Outils électroportatifs

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Makita VC001GL User manual
español: Makita VC001GL Manual de usuario

Makita VC001GL Manuel utilisateur

Makita VC001GL Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents