Lenco LPJ-700BKGY Manuel utilisateur

Model LPJ-700BKGY

User manual – HD 720P LCD projector with Bluetooth

Gebruikshandleiding – HD 720P LCD-projector met Bluetooth

Bedienungsanleitung – HD 720P LCD-Projektor mit Bluetooth

Mode d’emploi – Projecteur LCD HD 720P avec Bluetooth

Manual de usuario – Proyector LCD HD 720P con Bluetooth

1

Index

English ................................................................................................................ 2

Nederlands ........................................................................................................ 28

Deutsch ............................................................................................................. 57

Français ............................................................................................................ 88

Español ........................................................................................................... 117

Version : 4.0

2

English

CAUTION:

Usage of controls or adjustments or performance of procedures other than those

specified herein may result in hazardous radiation exposure.

PRECAUTIONS BEFORE USE

KEEP THESE INSTRUCTIONS IN MIND:

1. Do not cover or block any ventilation openings. When placing the device

on a shelf, leave

2. 5 cm (2”) free space around the whole device.

3. Install in accordance with the supplied user manual.

4. Keep the device away from heat sources such as radiators, heaters,

stoves, candles and other heat-generating products or naked flame. The

device can only be used in moderate climates. Extremely cold or warm

environments should be avoided. Working temperature between 0° and

35°C.

5. Avoid using the device near strong magnetic fields.

6. Electrostatic discharge can disturb normal usage of this device. If so,

simply reset and restart the device following the instruction manual. During

file transmission, please handle with care and operate in a static-free

environment.

7. Warning! Never insert an object into the product through the vents or

openings. High voltage flows through the product and inserting an object

can cause electric shock and/or short circuit internal parts. For the same

reason, do not spill water or liquid on the product.

8. Do not use in wet or moist areas such as bathrooms, steamy kitchens or

near swimming pools.

9. The device shall not be exposed to dripping or splashing and make sure

that no objects filled with liquids, such as vases, are placed on or near the

apparatus.

10. Do not use this device when condensation may occur. When the unit is

used in a warm wet room with damp, water droplets or condensation may

occur inside the unit and the unit may not function properly; let the unit

stand in power OFF for 1 or 2 hours before turning on the power: the unit

should be dry before getting any power.

11. Although this device is manufactured with the utmost care and checked

several times before leaving the factory, it is still possible that problems

may occur, as with all electrical appliances. If you notice smoke, an

excessive build-up of heat or any other unexpected phenomena, you

should disconnect the plug from the main power socket immediately.

3

12. This device must operate on a power source as specified on the

specification label. If you are not sure of the type of power supply used in

your home, consult your dealer or local power company.

13. Keep away from animals. Some animals enjoy biting on power cords.

14. To clean the device, use a soft dry cloth. Do not use solvents or petrol

based fluids.

15. To remove severe stains, you may use a damp cloth with dilute detergent.

16. The supplier is not responsible for damage or lost data caused by

malfunction, misuse, modification of the device or battery replacement.

17. Do not interrupt the connection when the device is formatting or

transferring files. Otherwise, data may be corrupted or lost.

18. If the unit has USB playback function, the USB memory stick should be

plugged into the unit directly. Don’t use an USB extension cable because it

can cause interference resulting in failing of data.

19. The rating label has been marked on the bottom or back panel of the

device.

20. This device is not intended for use by people (including children) with

physical, sensory or mental disabilities, or a lack of experience and

knowledge, unless they’re under supervision or have received instructions

about the correct use of the device by the person who is responsible for

their safety.

21. This product is intended for non professional use only and not for

commercial or industrial use.

22. Make sure the unit is adjusted to a stable position. Damage caused by

using this product in an unstable position vibrations or shocks or by failure

to follow any other warning or precaution contained within this user manual

will not be covered by warranty.

23. Never remove the casing of this device.

24. Never place this device on other electrical equipment.

25. Do not allow children access to plastic bags.

26. Only use attachments/accessories specified by the manufacturer.

27. Refer all servicing to qualified service personnel. Servicing is required

when the device has been damaged in any way, such as the power supply

cord or the plug, when liquid has been spilled or objects have fallen into

the device, when the device has been exposed to rain or moisture, does

not operate normally, or has been dropped.

28. Long exposure to loud sounds from personal music players may lead to

temporary or permanent hearing loss.

29. If the product is delivered with power cable or AC power adaptor:

4

⚫ If any trouble occur, disconnect the AC power cord and refer servicing to

qualified personnel.

⚫ Don’t step on or pinch the power adaptor. Be very careful, particularly

near the plugs and the cable’s exit point. Do not place heavy items on the

power adaptor, which may damage it. Keep the entire device out of

children’s reach! When playing with the power cable, they can seriously

injure themselves.

⚫ Unplug this device during lightning storms or when unused for a long

period.

⚫ The socket outlet must be installed near the equipment and must be

easily accessible.

⚫ Do not overload ac outlets or extension cords. Overloading can

cause fire or electric shock.

⚫ Devices with class 1 construction should be connected to a main

socket outlet with a protective earthed connection.

⚫ Devices with class 2 construction do not require a earthed

connection.

⚫ Always hold the plug when pulling it out of the main supply socket.

Do not pull the power cord. This can cause a short circuit.

⚫ Do not use a damaged power cord or plug or a loose outlet. Doing

so may result in fire or electric shock.

30. If the product contains or is delivered with a remote control containing

coin/cell batteries:

Warning:

⚫ “Do not ingest battery, Chemical Burn Hazard” or equivalent working.

⚫ [The remote control supplied with] This product contains a coin/button

cell battery. If the battery is swallowed, it can cause severe internal burns

in just

⚫ 2 hours and can lead to death.

⚫ Keep new and used batteries away from children.

⚫ If the battery compartment does not close securely, stop using the

product and keep it away from children.

⚫ If you think batteries might have been swallowed or placed inside any part

of the body, seek immediate medical attention.

31. Caution about the use of Batteries:

⚫ Danger of explosion if battery is incorrectly replaced. Replace only with

the same or equivalent type.

⚫ Battery cannot be subjected to high or low extreme temperatures, low air

pressure at high altitude during use, storage or transportation.

5

⚫ Replacement of a battery with an incorrect type that can result in an

explosion or the leakage of flammable liquid or gas.

⚫ Disposal of a battery into fire or a hot oven, or mechanically crushing or

cutting of a battery, that can result in an explosion.

⚫ Leaving a battery in an extremely high temperature surrounding

environment that can result in an explosion or that leakage of flammable

liquid or gas.

⚫ A battery subjected to extremely low air pressure that may result in an

explosion or the leakage of flammable liquid or gas.

⚫ Attention should be drawn to the environmental aspects of battery

disposal.

INSTALLATION

• Unpack all parts and remove protective material.

• Do not connect the unit to the mains before checking the mains voltage and

before all other connections have been made.

6

Do not connect the unit to the mains before checking the mains voltage and

before all other connections have been made.Packing Included:

Main unit

Remote (2 X

AAA batteries

not included)

AC Power

Adapter

Lens Cover

User Manual

7

Remove & Close The Lens Cover

Remove the lens cover before using

Close the lens cover

after use.

Placing Your Projector

Your projector can be installed in four different configurations (see picture below):

Table mounting front:

Select this location with the projector is placed

in front of the screen. This is the most common

way to position the projector for quick setup

and portability.

FRONT TABLE

Ceiling mounting front:

Select this location when the projector is mounted

upside down at the ceiling in front of the screen.

NOTE: A projector mount is required to mount

the projector on the ceiling.

FRONT CEILING

Table mounting rear:

Select this location if you want to place the

projector at the rear of the screen.

NOTE: That a special rear projection screen is

required.

REAR TABLE

Ceiling mounting rear:

Select this location when the projector is

mounted upside down at the ceiling at the rear

of the screen.

NOTE: That a projector mount and a rear

projection screen is required to mount the

projector on the ceiling.

REAR CEILING

8

To Reduce Image Distortion

Square/Rectangle

It is recommended to move the projector as close to

center of screen.

Distance Between The Projector And

Screen

Measure the distance between the projector and where you want to position the

screen. This is the projection distance and the screen diagonal indicated in

inches.

Screen diagonal

Inch

Screen diagonal

CM

Projection distance

Inch

Projection distance

CM

37

94

46

116

45

114

53

135

50

127

59

151

60

152

71

181

72

183

85

215

100

254

142

360

Screen

Projector

9

Placing Your Projector On Ceiling

When you mount the projector on the ceiling, make sure you purchase a

projector mount that is recommended for this use and follow the instructions that

come with the mount. Before installing the projector on the ceiling, please check

to make sure the ceiling structure can support the weight of the projector and the

mount. If in doubt, please ask the advice from an installation professorial.

NOTE: Projector mount and screw(s) not included

10

Adjust The Vertical Location

Follow below picture to adjust the vertical location.

Adjust The Focus And Keystone

Follow below picture to adjust the focus and trapezoidal screen.

Adjust the focus by turning the

adjusting wheel while observing the

image pixels near the center of the

screen. Optimal focus is obtained

when the pixels are clearly visible.

Depending on the projected screen

size, the focus near the screen edges

may be less sharp than the screen

center.

11

Keystone image is created when the

projector beam is projected to the

screen in an angle. Keystone

correction will restore the distorted

image to a rectangular or square

shape.

Controls Of Remote

Power

Press to power ON.

Long press to power OFF.

Previous/Next

Press to skip between chapters or tracks.

Stop

Press to stop playback.

Flip

Press to flip display image 180°.

Play/Pause

Press to play or pause an individual chapter

or track.

Arrows/OK

Press to navigate and confirm selections in

Settings and other menus.

Menu

Press to access projector Settings.

Go To/Number Keypad

Press to enter specific chapter or track

numbers. Use Play button to start playing.

Mute

Press to mute volume.

Back/Fwd

Press to search through an individual

chapter or track.

VOL+/VOL−

Press to adjust audio level.

Source

Press to select media source (AV, PC,

HDMI, MEDIA).

Exit

Press to exit menu.

Zoom

Press to zoom display image in or out.

12

Install/Remove Battery Of Remote

Remove the battery compartment cover on the back of your remote by carefully

sliding it open. The battery cover can then be lifted away. Fit the correct batteries

(2 X AAA batteries not included), referring to the polarity markings. Finally,

replace the cover.

NOTES:

• Batteries shall not be exposed to excessive heat such as direct sunlight, fire.

• Be sure to check the correct polarity when installing the batteries

• Do not mix old and new batteries.

• Only use type AAA/LR03/UM4 type batteries

• Do not throw batteries into fire because it may explode. Never try to

recharge a single use battery.

• Do not mix alkaline, standard (carbon-zinc), or rechargeable (ni-cad, ni-mh,

etc.) batteries.

13

Explanation

14

Controls

Install Power Adapter

Follow below picture to connect the power adapter.

First connect the round connector to the projector and then the adapter to the

power network.

Connect HDMI

Follow the picture below to connect a device with an HDMI cable.

1.

Turn off the projector before connecting the HDMI cable.

2.

After connecting, press the button to turn on the projector and the

15

power indicator will light up GREEN

3.

Press the /SOURCE button to go to HDMI mode and the video of the

HDMI device will show on the projector screen. There are 2 HDMI inputs,

HDMI1 interface corresponds to HDMI 1 in SOURCE mode, and HDMI2

interface corresponds to HDMI 2 in SOURCE mode.

4.

Press the button to turn off the unit power.

HDMI HD signal input

- Using a MHL HDMI cable:

This projector is compatible with MHL cables: this means that you can

connect your smartphone or tablet (if MHL compatible) and stream in HD

from your smartphone or tablet to the projector with a MHL cable (not

included).

- Using a Chromecast dongle:

The HDMI connectors are compatible with the use of a chrome cast dongle

to enable you to stream wirelessly from your smartphone or tablet

Connecting an AV Source

Follow the picture below to connect a device with an AV cable.

1.

Turn off the unit before connecting the AV cable.

2.

Use the AV cable to connect a device as shown in the image below.

3.

After connecting, press the button to turn on the projector and the power

indicator will light up GREEN

4.

Press the /SOURCE button to go to the AV mode and the video of AV

device will show on the projector screen.

16

5.

Press the button to turn off the unit power.

Connecting a VGA source

Follow the picture below to connect a device with a VGA cable.

1.

Turn off the projector before connecting the VGA cable.

2.

Press the button to turn off the power of your projector before

connecting.

3.

After connecting, press the button to turn on the projector and the

power indicator will up light GREEN

4.

Press the /SOURCE button to go to the VGA mode and the video of

VGA device will show on projector screen.

5.

Press the button to turn off the unit power.

Please refer to the following table to adjust the output signal from

computer.

Type

Resolution

Frequency

Field Frequency

17

PC

VGA

640x480

31.5

60

34.7

70

37.9

72

37.5

75

SVGA

800x600

31.4

50

35.1

56

37.9

60

46.6

70

48.1

72

46.9

75

XGA

1024x768

40.3

50

48.4

60

56.5

70

Connecting an Audio device

Follow the picture below to connect a device with an Audio cable.

1.

Press the button to turn off the power of your projector before

connecting.

2.

Use the audio cable to connect the devices as shown in the image below.

3.

After you have connected both devices you will hear the sound through the

connected device.

4.

Switch off both devices after use.

Station Amplifier

18

Connect USB Device And Micro SD Card

“TF”

Follow below picture to connect a USB stick and Micro SD card.

Turn off the projector before connecting the USB/Micro SD card.

Using a Micro SD Card or USB Stick

Connect USB/Micro SD device:

1. Turn off the unit before connecting USB/Micro SD card.

2. Connect the USB device to the USB port.

3. After connecting, press the button to turn on the projector and the

power indicator light up GREEN.

4. Press the /SOURCE button to enter and use the buttons to search the

MEDIAPLAYER mode.

5. After selection, use the buttons to search the MUSIC/PHOTO/MOVIE

icon and press the button to enter, if necessary, use the button to

select Micro SD card or USB and press the button to enter.

6. Use the buttons to search the correct file and press the button to

preview playback file and press the button of unit or button of

remote to start playback.

7. Press button to search forwards and backwards quickly.

8. Press button to search next or previous file.

9. During playback, press the button to pause and press again to resume.

NOTE: Remove USB/Micro SD card device, press the button to turn off

power FIRST.

MICRO SD

19

Sub-Menu on Photo screen

1.

While playing photos, press the

button and more function

are being displayed (ﬁgure 1).

2.

Use the button to select

icon and press button to

play special function.

Figuur 1.

Sub-Menu on Music screen

3.

While playing music, press the

button and more function

are being displayed (ﬁgure 2).

4.

Use the button to select

icon and press button to

play special function.

Figuur 2.

Sub-Menu on Movie screen

5.

While playing a movie, press the

button and more function are

being displayed (ﬁgure 3).

6.

Use the button to select

icon and press button to

play special function.

Figuur 3.

La page charge ...

Lenco LPJ-700BKGY Manuel utilisateur

Lenco LPJ-700BKGY Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents