Kinetico 2060s Le manuel du propriétaire

Owner’s Manual • Guide d’utilisation • Manual del usuario

High Performance Water Conditioning

and Combination Systems

Adoucisseurs d’eau et systèmes combinés performants

Acondicionadores de agua de alto desempeño

y sistemas combinados

High Performance Conditioning

and Combination Systems

Owner’s Manual

Congratulations for choosing Kinetico to improve the quality of your water.

You will immediately begin to notice the numerous beneﬁts of having quality

water throughout your home and the beneﬁts of having a Kinetico Quality

Water System.

Since 1970, Kinetico Incorporated has designed and manufactured products

to improve the quality of your water. Kinetico oﬀers a complete line of quality

water systems to solve your water problems. Pioneers in non-electric, demand

operated water treatment, Kinetico continually sets the direction for the entire

water quality industry.

“Kinetico,” the Kinetico logo, and “Overdrive” are registered trademarks in the

United States, other countries or both, of Kinetico Incorporated, Newbury, Ohio.

2

Table of Contents

Kinetico Water Conditioners and Combination Systems . . . . . . . . . . . . . . . . . . . 3

What Makes Your Kinetico Water System Different

Is What Makes It Better ................................................... 5

How Your Water System Works .......................................... 7

Kinetico Combination Systems ........................................... 8

Maintaining Your Water System

Changing the Filter ............................................. 10

Adding Regenerant ............................................. 11

Manual Regeneration ........................................... 12

By-pass ........................................................ 12

Cold Weather Protection ....................................... 13

Sanitizing the System ........................................... 13

Iron Cleaning .................................................... 13

Salt Bridge ...................................................... 13

Commonly Asked Questions ............................................ 14

Glossary of Terms ....................................................... 16

Softening System Diagram .............................................. 17

Product Speciﬁcations .................................................. 18

Maintenance Record .................................................... 20

Kinetico Incorporated

10845 Kinsman Rd.

Newbury, Ohio, 44065

USA

www.kinetico.com

Kinetico UK Limited

Bridge House

Park Gate Business Centre

Chandler’s Way

Park Gate SO 31 1FQ

England

www.kinetico.co.uk

Kinetico Canada Incorporated

21 Parr Blvd., Unit 10

Bolton, ON L7E 4G3

Canada

www.kinetico.com

Kinetico France

Sarl

B.P. 80528 Osny

95528 Cergy-Pontoise Cedex

France

www.kinetico.fr

Kinetico Denmark

ApS

Sandvadsvej7

4600 Køge

Denmark

Kinetico Germany GmbH

Bunzlauerstrasse 12-D

Höher-Grenzhausen

Germany 56203

3

2

1

Kinetico Water Conditioners

and Combination Systems

Now that your Kinetico water system is installed, you can enjoy all the beneﬁts

of having soft water. If you are not accustomed to soft water, here are some tips

to follow to get the most beneﬁt from your new system:

How to use soft water

Use pure soap products.

Most leading brands of laundry soaps, household cleaners and shampoos

contain large amounts of detergents. e harsh chemicals in these detergents

are necessary when using hard water, but you can reduce your use or eliminate

them altogether with soft water. We recommend you use pure soap products;

clear liquid soaps without dyes and perfumes. If you continue to use your

normal detergents, you should signiﬁcantly reduce the amount used. Your

local, authorized Kinetico dealer can provide you with more information and

recommended detergent amounts.

Use less soap and household cleaners.

When using soap or cleaners with soft water, start by cutting the amount

of soap you normally use in half. You may even ﬁnd you can use as little as

one-quarter the amount you were using before. Hardness minerals in water

interfere with soap’s cleaning ability. Once they are removed, soap can do its job

better. Even though you’ll use less soap, you’ll get more suds and cleaner results.

It’s especially important to reduce the amount of laundry soap you use. Washing

clothes in soft water not only means you’ll need less soap to get your clothes

clean, but also that the soap you do use will rinse out completely. Washing

in soft water makes your clothes look whiter and brighter, and they’ll last

longer too. It is very important not to let your clothes sit in the washer after

the cycle is complete. Otherwise, mildew and a musty smell could develop.

Detergent buildup can stain your clothing. Again, Kinetico recommends that

you use clear, liquid soaps, without dyes or perfumes.

After bathing in soft water, your skin should feel “slippery.” It’s not soap left on

your skin. What you’re feeling is your own smooth skin without any leftover

soap curd or residue. When you bathed in hard water, you were never able to

rinse this residue oﬀ completely. e soap curd that left a ring in your bathtub

was also left on your skin. But now that you have soft water, you’ll feel soft,

smooth and clean. e same holds true for rinsing shampoo out of your hair.

4

5

3

Reduce or eliminate the use of fabric softeners.

Fabrics washed in hard water retain soap curd or residue making them

“crackle” when removed from the dryer or stiﬀ if air-dried. Fabric softeners are

necessary with hard water to keep your clothing soft, but with soft water, you

can reduce your use of fabric softeners or eliminate them altogether.

Take special precautions with automatic dishwashers.

Soft water, when combined with caustic phosphates

in some dishwasher detergents and very high

temperatures in the dry cycle, can etch dishes

and glassware. To prevent this possibility:

• use the “no heat” dry cycle on your dishwasher;

• use the minimum amount of a good quality,

low phosphate dishwasher detergent needed

to clean your dishes. is may be as little as

20 percent of the amount recommended by

the appliance manufacturer or on the dishwasher

soap box;

• wash good china and crystal by hand.

Special care for plants and ﬁsh.

Depending on your water hardness level, amount of rainfall and how often you

water, you could use soft water for outside watering, but

why waste your soft water? Water your lawn, shrubs

and outside plants from an outside hard water faucet

or put your Kinetico water system in by-pass before

watering. See “By-pass” on page 12 for instructions

on by-passing your system. Many houseplants can be

watered with soft water, although some houseplants

can be highly sensitive to the elevated level of sodium

ions in soft water. You may prefer to water houseplants

with hard water or water from a Kinetico reverse

osmosis system.

Fish accustomed to hard water may have trouble with an abrupt change to soft

water. Make the change gradually over a period of seven to 14 days by blending

hard and soft water until the tank contains 100 percent soft water. Once you

begin using soft water, you should notice that your ﬁsh tank stays cleaner longer.

5

What Makes Your Kinetico Water System

Different Is What Makes It Better

Kinetico water systems are powered by the energy of moving water, not electricity.

So there’s nothing to plug in, no buttons to push, timers to set and reset, or

adjustments to make. You really don’t need to do anything special to operate your

Kinetico water system —it runs itself, not you.

Your Kinetico water system has a built-in water meter which means it operates

“on demand” based on your actual water usage. With demand operation, your

Kinetico water system can regenerate at any time of the day or night and you’ll

still have plenty of soft water available. It regenerates when necessary, so a simple

ﬂush of the toilet or run of the faucet can send your Kinetico water system into

regeneration. Depending on your water usage, your Kinetico water system could

regenerate more frequently (if you have a house full of guests, for instance) or

not at all for several days (if you’re on vacation). Demand operation ensures

maximum eﬃciency while providing you with a

continuous supply of soft water — even as your

water usage changes.

e actual regeneration process of a

Kinetico water system is diﬀerent from other

systems. Kinetico water systems use a process

called countercurrent regeneration (instead of an

old fashioned, 4- or 5-cycle regeneration) which

has long been recognized as the optimum process

for regenerating a resin bed (Fig. 1). Kinetico is

able to eﬀectively use this process since our water

systems regenerate with soft water.

e twin tank design of a Kinetico water

system provides you with a continuous supply

of soft water any time of day, even through the

regeneration process. When one tank needs to

regenerate, service automatically switches to the

other tank (Fig. 2). So go ahead and do a week’s

worth of laundry in one day. Your Kinetico water

system can handle it.

Highly Efﬁcient Regeneration

Kinetico systems clean

themselves with soft water

using countercurrent

regeneration. This process

reduces regenerant and water

usage and regenerates the

resin beads more effectively.

Fig. 1

6

Fig. 2

Twin Tank Design

Twin tanks provide an uninterrupted

supply of soft water, 24 hours a day.

Overdrive® Enhanced

Select Kinetico softening, ﬁltration and combination systems are Overdrive

enhanced for maximum performance and eﬃciency. With Overdrive, you can

expect better ﬂow without compromising water quality.

Overdrive directs the ﬂow of water through both tanks of the system

simultaneously during service cycles. Water ﬂow is distributed evenly between

the tanks, increasing ﬂow, increasing contact time with media and decreasing

pressure loss through the system. During a regeneration cycle, one tank

is available to provide normal service ﬂow. When the cycle is complete, both

tanks are immediately placed back into service.

Should you have any questions or need any assistance, contact your local,

authorized Kinetico dealer.

NOTE: Repair leaky faucets, toilets or pipes to ensure proper product

performance.

7

How Your Water System Works

Hard water contains calcium and magnesium. Your Kinetico water system

contains resin beads, which hold sodium ions. When hard water passes through

the resin beads (Fig. 3) inside a Kinetico water system, the beads attract and

hold the calcium and magnesium ions in exchange for sodium. After this ion

exchange process, the water leaving your Kinetico water system is soft.

Once the resin bed is loaded with calcium and magnesium ions, it must be

cleansed (or regenerated) so that it can continue to soften water. e salt in your

salt storage tank mixes with water to wash the resin beads. e brine solution

loosens the hardness minerals which have built up on the resin beads; then the

system backwashes and ﬂushes the hardness minerals and salt solution away.

Once this is complete, the resin beads hold sodium ions. e system is again

ready to exchange the sodium ions for more calcium and magnesium ions.

Softening

Cycle

Regeneration

Cycle

Fig. 3

8

Unlike most other systems, the Kinetico water system’s cleaning or regeneration

process is done with soft water. Since you already know what a diﬀerence cleaning

with soft water can make throughout your home, it only makes sense that the

Kinetico water system cleans itself with soft water too. And only clean, soft water

is used to make the salt solution in the salt storage tank.

Kinetico Combination Systems

Your Kinetico combination system is two systems in one! It provides additional

ﬁltration capabilities above and beyond the softening performed by a standard

Kinetico water system. Kinetico combination systems have the same great features

that make our water systems so unique (see “What Makes Your Kinetico Water

System Diﬀerent...” section of this manual) as well as additional technology

designed to provide you with the best water possible.

Kinetico offers the following combination systems:

Kinetico 4040s with Overdrive

High eﬃciency water softening system with two tanks of activated carbon for

whole-house dechlorination. Removing chlorine from your water allows you

to enjoy odor-free showers, eliminate the skin-drying eﬀects of chlorine, and

prevent premature fading/bleaching of your favorite clothing and linens.

Kinetico 4060s with Overdrive —Activated Carbon

Water softening system with two tanks of activated carbon for whole-house

dechlorination.

Kinetico 4060s with Overdrive—Macrolite®

Water softening system with two tanks of Macrolite ﬁne ceramic ﬁltration

media for whole-house ﬁltration of ferric (oxidized) iron and particles and the

removal of cloudiness. Filtering unwanted particles and elements from your

water helps to minimize staining, and prolong the life of your appliances and

plumbing system.

9

Overdrive Enhanced

Kinetico combination systems incorporate proven ﬁltration technology

to ensure optimum water quality. Kinetico’s unique design passes water

through all four tanks simultaneously, dramatically improving the ﬂow and

ﬁltration performance of the systems. With Overdrive enhanced systems,

you can rest assured you’re getting the best water possible.

Care and Maintenance of Your Combination System

To ensure your Kinetico combination system continues to operate at peak

performance, follow the procedures outlined in the “Maintaining Your System”

section of this owner’s manual.

e concentration of chlorine in a water supply will determine the life of the

carbon in combination systems. You will have to replace the carbon in your

system when you begin to notice the return of a chlorine odor in your water.

Expect to replace the carbon every few years as a general rule, although it may

last longer if your water supply does not contain high levels of chlorine.

Because Kinetico’s Macrolite filtration media is automatically cleaned

when the 4060s goes into regeneration, it requires no additional

maintenance or replacement.

If you have additional questions about the

operation and maintenance of your Kinetico

combination system, please contact your local,

authorized Kinetico dealer.

Kinetico 4040s with Overdrive

Combination System

10

Maintaining Your Water System

Your Kinetico water system is engineered to provide you with quality water

without requiring extensive maintenance. However, some routine maintenance

is necessary to keep your system working properly.

Changing the Filter

Your Kinetico system uses an in-line ﬁlter to remove solid material from the

inlet water supply. Periodically, the ﬁlter cartridge will require replacement.

is should occur when the water pressure in the home begins to gradually

decrease. e frequency of the ﬁlter change is determined by the amount of

water used and the solid material content of your water supply.

Procedure

1. Turn oﬀ the feed water to the ﬁlter by turning the by-pass valve 1 to the BY-

PASS position*.

2. Slowly turn the handle on the pressure relief valve 2 to the OPEN

position**. Allow at least one minute for system to depressurize and to

minimize spillage.

Open

Closed

Off

On

2

1

5

3

6

4

11

3. When depressurized, remove the ﬁlter sump 3 by turning it clockwise

(when viewed from above) with two hands.

4. Remove the new cartridge and all contents from the protective bag, and

slide the bag over the used cartridge.

5. Remove the used cartridge by turning it clockwise. Discard used cartridge with

the bag, or clean and store for reuse.

6. Inspect and clean the sump seal and adapter O-ring, if necessary. Using the

included packet of silicone, lubricate entire seal, O-ring and the sealing surface

in the ﬁlter head 4.

7. Install the new cartridge into the cartridge adapter by turning it counter-

clockwise until it stops 5.

8. Install the ﬁlter sump by turning it counter-clockwise until it stops.

IMPORTANT! Check alignment of arrows to assure proper assembly 6.

9. Turn the handle on the pressure relief valve to the CLOSED position 2.

10. Turn on the feed water by slowly turning the by-pass to the GREEN, “IN

SERVICE” position*.

* Your by-pass valve may be diﬀerent than the one illustrated.

** Pressure relief valve may be in a diﬀerent location than illustrated. If necessary, contact your Kinetico

dealer for assistance.

NOTE: Filter styles vary, and yours may not be exactly as previously

described.

Adding Regenerant

(water softener salt or potassium chloride)

Make sure your salt storage tank never runs out of regenerant. Reﬁll regenerant

anytime before water is visible in the brine drum or softener cabinet (on cabinet

models). Use Kinetico Water Softener Salt, available from most Kinetico dealers,

or another quality brand. Some salts contain foreign particles which can cause

problems with your system, so be sure to use a quality grade of salt, processed

especially for use in water softeners. If you choose to use potassium chloride,

contact your local authorized Kinetico dealer to ﬁnd out about the recommended

adjustments to your system. Your Kinetico dealer can also recommend or perform

a schedule of periodic maintenance. DO NOT USE ROCK SALT, as it often

contains signiﬁcant levels of dirt or foreign matter.

12

Manual Regeneration

If your salt storage tank does run out of

salt, you can manually regenerate the unit

after adding salt, or you can wait for it to go

through regeneration automatically.

Using a #2 Phillips screwdriver, push down

ﬁrmly on the softener valve screw (Fig. 4) and

slowly turn clockwise until the actuator has advanced the indicator dot to the

“BRINE” position (Fig. 4). You should hear at least ﬁve “clicks” while turning

the screw before the indicator dot reaches the “BRINE” position. At this point

you should hear water begin to run through the system. If you do not hear water

running through the system, the indicator dot has not been advanced far enough.

Repeat the procedure for manual regeneration after the water ﬂow stops (11 to 90

minutes, depending on the model) to be sure both resin tanks are regenerated.

NOTE: If your hot water tank has reﬁlled with hard water, it may take several

days for it to empty and for your water to feel soft again.

By-pass

ere may be times when you need to shut oﬀ the water supply to your entire

house. To do this, set the by-pass valve to the RED, “OFF” position. No water

will ﬂow through the house. To restart the water, set the by-pass valve to the

GREEN, “IN SERVICE” position. You may put the softener into by-pass at any

time, if necessary, by putting the by-pass valve into the YELLOW, “BY-PASS”

position. You will still get water throughout the house; however, all of the water

will be untreated. To return the softener to service, set the by-pass valve to the

GREEN, “IN SERVICE” position.

NOTE: By-pass styles vary and yours may not be as described.

Contact your Kinetico dealer for further assistance.

Indicator

Dot

Softener

Valve Screw

Fig. 4

13

Cold Weather Protection

If your Kinetico water system is installed outside or in an area that is not

heated, you may want to take precautionary measures to prevent damage to

your unit from freezing.

NOTE: Kinetico’s warranty doesn’t cover damage to your system due to freezing.

If you have questions about your Kinetico water system, or if you suspect that it

isn’t working properly, contact your local, authorized Kinetico dealer.

Sanitizing the System

Kinetico water systems are intended for use on microbiologically safe water

supplies. If the inlet water supply’s safety is compromised for any reason

(for example a “Boil Alert” from a municipal supply or positive bacteria test

on a well), you should by-pass the system until bacteriological safety has been

restored. You should then contact your Kinetico dealer to sanitize the system

before returning the system to service.

Iron Cleaning

If the inlet water supply contains iron, it is a good idea to use salt that contains an

iron cleaning additive (for example, Kinetico Salt with Iron Fighter* additive).

e iron cleaning additive will prevent iron from fouling the resin and keep your

system in optimal condition. Alternately, you can add iron cleaning agents in

powder form to the brine tank when you replenish the salt supply. Contact

your Kinetico dealer for additional information about iron cleaning.

Salt Bridge

e regenerant in the brine tank can, under certain conditions, solidify and

form a “salt bridge” preventing the system from making brine for regeneration.

Conditions known to contribute to salt bridging include high humidity, low

water and salt consumption, or the use of potassium chloride (KCl). If a salt

bridge occurs, you can attempt to break up the solidiﬁed salt by carefully

poking the salt with a stick or broom handle.

To minimize the potential for salt bridging, ﬁll the brine tank to the halfway

point with regenerant. Or, consider using the K-Spray Brine System (optional

equipment available from your Kinetico dealer) that virtually eliminates

salt bridging.

*Iron Fighter is a licensed trademark of Cargill, Incorporated.

14

Commonly Asked Questions

ere has been a drop in my home’s water pressure.

What can be the cause?

A reduction in your home’s water pressure can indicate that it is time to

change your ﬁlter. See pages 10 and 11 for instructions on changing the ﬁlter.

If you do not have a ﬁlter with your system or changing the ﬁlter has no eﬀect,

contact your local, authorized Kinetico dealer.

My system seems to be regenerating more frequently. Is this normal?

Remember, your Kinetico system is demand-operated, adjusting automatically

to your water usage. If you do not think that your water usage has increased

due to extra house guests, additional laundry or some other reason, check

for any leaky plumbing, dripping faucets or running toilets; all of which can

contribute to more frequent regenerations.

My water doesn’t seem soft. How can I be sure that my system is

regenerating properly?

Be sure that the water supply to the softener is not by-passed. Follow the

instructions on page 12 to manually regenerate the softener tanks. If the unit

does not begin advancing to the next regeneration automatically, please contact

your local, authorized Kinetico dealer for further assistance.

I can hear my Kinetico system running or regenerating during the day.

My old softener only used to run at night. Is this normal?

Single tank, electric water softeners tend to be set to regenerate at night

because of the unavailability of soft water during the regeneration process.

Unlike traditional water softeners, Kinetico systems operate on demand based

on your water usage, without timers or electronics. So your system regenerates

whenever necessary, at any time of day. And Kinetico’s twin tank design allows

one tank to provide treated water while the other regenerates, so you’ll never

be without soft water.

How will I know when it is time to add salt?

Lift the lid of the brine tank to check the level of salt. If you can see water,

it is time to add salt. You can add salt anytime there is enough room to

accommodate at least one bag. However, keep in mind that keeping the brine

tank completely full of salt can contribute to salt bridging (see page 13).

15

Is it OK to drink soft water?

Yes, soft water is OK for drinking and cooking. If your softener regenerates

with sodium chloride (salt), keep in mind that there will be a small amount of

sodium added to the softened water (see page 18). People who are on sodium-

restricted diets should consider the added sodium as part of their overall

sodium intake. For the highest quality drinking water possible, a Kinetico

reverse osmosis drinking water system will remove as much as 98 percent of

total dissolved solids from your water.

— • —

If at any time you feel your Kinetico water system is not operating properly, put

the system in by-pass and call your local, authorized Kinetico dealer. To assure

that the barium and radium reduction capability of the system is maintained,

make sure the system is working eﬀectively. Soft water indicates that the reduction

of contaminants will occur as expected. Contact your local dealer for information

and directions for the procedure to test your water hardness.

16

Glossary of Terms

Automatic: Softeners or back-washing ﬁlters that start regeneration via clock.

Backwash: High velocity rinsing of softening resin or ﬁltration, normally upﬂow.

Brine: Salt solution used to regenerate resin.

Brine Tank: Holds salt to make brine for regeneration.

By-pass: Manually operated valves to divert ﬂow around POE equipment,

or, automatic diversion of ﬂow inside a controller for single tank POE during

regeneration.

Carbon: Activated carbon found in POE equipment for dechlorination, taste and

odor reduction.

Combination System: Duplex combination filter / softener system using

four separated media tanks and one control.

Counter-current: Direction of service ﬂow and regeneration ﬂow are opposite.

DIR: Demand initiated regeneration.

Downﬂow: Direction of water ﬂow with gravity through resin or ﬁltration media.

Efﬁciency: Referring to grains of hardness removed / pound of salt for a water

softener.

gpg: Grains per gallon of hardness.

1 US gpg = 17.1 ppm of hardness as CaCO3.

gpm: Gallons per minute.

gpp: Grains per pound (salt eﬃciency).

Macrolite: Engineered ceramic ﬁltration media.

Meter: Device to measure ﬂow to service from POE softener or ﬁlter for DIR.

Micron: Micrometer (µm) for solid particle diameter.

Overdrive: Parallel service ﬂow

ppm: Parts per million.

17

Peak ﬂow rate: Maximum design process ﬂow for intermittent high demand

through POE ﬁlter or softener.

POE: Point of Entry. A system installed where water enters the home.

psi: Pounds per square inch.

Regeneration: e process of restoring exchange capacity to a softener.

Resin: For POE softeners, strong acid cation exchange beads operating in the

sodium or potassium form.

Sanitize: e periodic addition of a sanitizing agent such as chlorine to attempt

microbiological control.

Service ﬂow: Process water ﬂow rate through a POE system, often measured at

the point of 15 psi lost.

Simplex: Softener or ﬁlter using one media tank.

Upﬂow: Direction of water ﬂow against gravity through resin or ﬁltration media.

By-pass Valve

Softening System Diagram

Regeneration Cycle

Indicator

Control Valve

Brine Tank

Resin Tanks

18

* Meets California eﬃciency requirements of 4000 grains exchanged per pound of salt used. Eﬃciency is only

certiﬁed at the low salt dosage and was determined in accordance with NSF/ANSI 44.

Sodium Information: Systems using sodium chloride for regeneration will add sodium to the water. e

amount of sodium added is proportionate to the amount of hardness removed. People who are on sodium-

restricted diets should consider the added sodium as part of their overall sodium intake.

Inlet Hardness Sodium Added

171 mg/L (10 gr) 79 mg/L

342 mg/L (20 gr) 149 mg/L

513 mg/L (30 gr) 223 mg/L

1192 mg/L (40 gr) 298 mg/L

Kinetico reverse osmosis systems will remove as much as 98 percent of sodium content in the water. Using

potassium chloride as a regenerant will not add sodium to the water.

Model 2030s 2040s with

Overdrive

2040c with

Overdrive

2050s

2050c

(Europe

only)

2060s 2060s with

Overdrive

2100s 2100s with

Overdrive

2175s 4040s with

Overdrive

4050s

(Europe

Only)

4060s with

Overdrive-

Activated

Carbon

4060s with

Overdrive-

Macrolite

Certiﬁed ﬂow rate

@ 15 psi (or less)

9 gpm

34.1 Lpm

11 gpm

41.6 Lpm

7 gpm

26.5 Lpm

11.6 gpm

43.9 Lpm

20.5 gpm

77.6 Lpm

11 gpm

45.4 Lpm

21 gpm

79.5 Lpm

16.4 gpm

62.1 Lpm

11 gpm

41.6 Lpm

6 gpm

22.7 Lpm

11 gpm

41.6 Lpm

10 gpm

37.9 Lpm

Peak ﬂow rate @

30 psi (or less)

16.5 gpm

62.5 Lpm

15 gpm

56.7 Lpm

15 gpm

56.7 Lpm

30 gpm

113.5 Lpm

30 gpm

113.5 Lpm

19 gpm

71.9 Lpm

31 gpm

117.3 Lpm

22 gpm

83.2 Lpm

15 gpm

56.7 Lpm

15 gpm

56.7 Lpm

15 gpm

56.7 Lpm

15 gpm

56.7 Lpm

Resin per tank,

in cubic feet

0.47 0.4 0.4 0.7 0.7 1.5 1.5 2.25 Upper: 0.4

Resin

Lower: 0.4 Carb

Upper: 0.4 Resin

Lower: 0.4 Carb

Upper: 0.25

Carb

Lower: 0.7 Resin

Upper: 0.2

Macrolite

Lower: 0.7 Resin

Resin per tank, in liters 13.3 11.3 11.3 19.8 19.8 42.5 42.5 63.7 Upper: 11.3

Resin

Lower: 11.3 Carb

Upper: 11.3 Resin

Lower: 11.3 Carb

Upper: 7.1 Carb

Lower: 19.8 Resin

Upper: 5.7

Macrolite

Lower: 19.8

Resin

Capacity per cycle,

in grains @ salt used per

cycle setting pounds

7867 @ 1.8*

9802 @ 2.7

5222 @ 1.0* 5222 @ 1.0* 12,481 @ 2.7*

15,817 @ 4.0

12,481 @ 2.7*

15,817 @ 4.0

25,253 @ 5.5*

41,087 @ 10.0*

25,253 @ 5.5*

41,087 @ 10.0*

65,139 @ 15*

81,845 @ 30

4921 @ 1.0* 4921 @ 1.0* 13,715 @ 4.0 14,883 @ 4.4

Capacity per cycle, in

grams @ salt used per

cycle setting kilograms

509 @ 0.81*

635 @ 1.2

338 @ 0.45* 338 @ 0.45* 809 @ 1.23*

1025 @ 1.8

809 @ 1.23*

1025 @ 1.8

1636 @ 2.5*

2662 @ 4.5*

1636 @ 2.5*

2662 @ 4.5*

4221 @ 6.8*

5303 @ 13.6

319 @ 0.45* 319 @ 0.45* 889 @ 1.8 964 @ 2.0

Grains exchanged

per pound of salt used

4371 @ 1.8*

3630 @ 2.7

5222 @ 1.0* 5222 @ 1.0* 4623 @ 2.7*

3954 @ 4.0

4623 @ 2.7*

3954 @ 4.0

4591* @ 5.5*

4109* @ 10.0*

4591* @ 5.5*

4109* @ 10.0*

4343* @ 15.0*

2728 @ 30.0

4921 @ 1.0* 4921 @ 1.0* 3429 @ 4.0 3383 @ 4.4

Grains exchanged per

kilograms of salt used

628 @ 0.81*

529 @ 1.2

751 @ 0.450* 751 @ 0.450* 658 @ 1.23*

569 @ 1.8

658 @ 1.29*

569 @ 1.8

654 @ 2.5*

592 @ 4.5*

654 @ 2.5*

592 @ 4.5*

621 @ 6.8*

390 @ 13.6

709 @ 0.45* 709 @ 0.45* 494 @ 1.8 482 @ 2.0

Max. ﬂow rate to drain

during regenerations

0.69 gpm

2.6 Lpm

1.5 gpm

5.7 Lpm

1.5 gpm

5.7 Lpm

2.5 gpm

9.5 Lpm

2.5 gpm

9.5 Lpm

3.3 gpm

12.5 Lpm

3.3 gpm

12.5 Lpm

4.8 gpm

18.2 Lpm

3.0 gpm

11.4 Lpm

3.0 gpm

11.4 Lpm

3.0 gpm

11.4 Lpm

3.0 gpm

11.4 Lpm

Min./Max. operating

pressure

103.4 - 861.9 kPa

15 - 125 psi

172.3 - 861.9 kPa

25 - 125 psi

103.4 - 861.9 kPa

15 - 125 psi

Min./Max. operating

temperature

2 - 49°C

35 - 120°F

Max. working

pressure in psi

861.9 kPa

125 psi

Product Speciﬁcations

La page charge ...

Kinetico 2060s Le manuel du propriétaire

Ce manuel convient également à

Kinetico 2060s Le manuel du propriétaire

dans d''autres langues

Autres documents