Tripp Lite BP Series External Battery Packs Le manuel du propriétaire

1

Owner’s Manual

BP Series

External Battery Packs

Not suitable for mobile applications.

Introduction 2

Important Safety Instructions 2

Mounting 4

Connection 11

Maintenance 12

Warranty and Product Registration 13

Español 14

Français 27





40

1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support

PROTECT YOUR INVESTMENT!

Register your product for quicker service and ultimate peace of mind.

You could also win an ISOBAR6ULTRA surge protector—a $100 value!

www.tripplite.com/warranty

24V Battery Packs 36V Battery Packs 48V Battery Packs 72V Battery Packs

BP24V15RT2U, 14AH

BP24V28-2U, 28AH

BP24V36-2US, 36AH

BP24V70-3U, 70AH

BP36V15-2U, 18AH

BP36V42-3U, 21AH

BP48V24-2U, 18AH

BP48V27-2US, 27AH

BP48V60RT-3U, 42AH

BP72V15-2U, 15AH

BP72V18-2US, 18AH

BP72V28RT-3U, 28AH

18-05-292-9336FF.indb 1 7/16/2018 9:07:56 AM

2

Introduction

Important Safety Instructions

Tripp Lite BP Series External Battery Packs are designed for use with various Tripp Lite

UPS systems equipped with external battery pack connectors.

SAVE THESE INSTRUCTIONS

WARNING! The mounting shelves are not intended to support more than

one battery pack. Do not stack multiple battery packs on a single set of

mounting shelves. Failure to follow this warning may lead to product

damage and/or risk of personal bodily harm.

• Use caution when lifting battery packs. Because of the considerable weight of

all battery packs, at least two people should assist in lifting and installing

them.

• Make certain the battery packs and UPS use the same DC voltage before

connecting them.

• Use only Tripp Lite external battery packs with overcurrent protection.

Installation is by qualified service personnel only. Contact Tripp Lite Customer

Support at 773.869.1234 for the appropriate Tripp Lite battery pack to

connect.

• Your external metal battery cabinets are provided with a means for

equipotential protective bonding for safety. When using 2-pin connector

external batteries, be sure to bond the metal enclosure of your external

battery to the metal enclosure of the UPS system. Three-pin/conductor battery

packs are equipped with a ground bond plug. Plastic enclosures do not require

bonding. See below for ground bonding strap requirements:

24V Battery Packs

BP24V15RT2U: Plastic enclosure, so ground bonding strap is not required.

BP24V28-2U: 12 AWG ground bonding strap

BP24V36-2US: 12 AWG ground bonding strap

BP24V70-3U: 12 AWG ground bonding strap

36V Battery Packs

BP36V15-2U: 12 AWG ground bonding strap

BP36V42-3U: 12 AWG ground bonding strap

48V Battery Packs

BP48V24-2U: 12 AWG ground bonding strap

BP48V27-2US: 12 AWG ground bonding strap

BP48V60RT-3U: 12 AWG ground bonding strap

Note: The battery connector on 72V battery packs has a built-in ground bonding plug, so an

additional ground bonding strap isn’t needed.

18-05-292-9336FF.indb 2 7/16/2018 9:07:56 AM

3

Important Safety Instructions

Securely attach the provided ground strap to the UPS system as illustrated

below:

• Use of this equipment in life support applications where failure of this

equipment can reasonably be expected to cause the failure of the life support

equipment or to significantly affect its safety or effectiveness is not

recommended. Do not use this equipment in the presence of a flammable

anesthetic mixture with air, oxygen or nitrous oxide.

• Suggested mounting procedures are for common rack types and may not be

appropriate for all rack configurations. User must determine the fitness of rack and

wall-mount hardware and procedures before mounting.

• When connecting multiple battery packs to a single UPS, the battery packs should be

approximately the same age.

• It is normal for sparks to occur when connecting external batteries.

• Do not unplug external batteries from the UPS while the UPS is operating on battery

power, due to the possibility of dangerous arcing.

• Batteries can present a risk of electrical shock and burn from high short-circuit

current. Observe proper precautions. Do not dispose of the batteries in a fire. Do not

open the UPS or batteries. Do not short or bridge the battery terminals with any

object. Unplug and turn off the UPS before performing battery replacement. Use tools

with insulated handles. There are no user-serviceable parts inside the UPS. Battery

replacement should be performed only by authorized service personnel using the

same number and type of batteries (Sealed Lead-Acid). The batteries are

recyclable. Refer to your local codes for disposal requirements or visit

http://www.tripplite.com/support/recycling-program for recycling information. Tripp Lite

offers a complete line of UPS System Replacement Battery Cartridges (R.B.C.).

Visit Tripp Lite on the Web at http://www.tripplite.com/products/battery-finder/ to locate

the specific replacement battery for your UPS.

18-05-292-9336FF.indb 3 7/16/2018 9:07:56 AM

4

Mounting (Rack)

Mount your rackmount battery pack in either a 4-post or 2-post rack or rack enclosure

(see page 6 for 2-post mounting). The user must determine the fitness of hardware and

procedures before mounting. If hardware and procedures are not suitable for your

application, contact the manufacturer of your rack or rack enclosure. The procedures

described in this manual are for common rack and rack enclosure types and may not be

appropriate for all applications.

4-Post Mounting

Most external battery packs include the hardware required for 4-post mounting. If this

hardware did not come with your unit, an Adjustable 4-Post Rackmount Shelf Kit

(Model 4POSTRAILKIT) may be ordered separately.

1

The included plastic pegs

A

will temporarily support the empty rackmount shelves

B

while you install the permanent mounting hardware. Insert a peg near the center

of the front and rear bracket of each shelf as shown. (Each front bracket has

6 holes and each rear bracket has 3 holes.) The pegs will snap into place.

After installing the pegs, expand each shelf to match the depth of your rack rails.

The pegs will fit through the square holes in the rack rails to support the shelves.

Refer to the rack unit labels to confirm the shelves are level in all directions.

Note: The support ledge of each shelf must face inward.

B

1

A

18-05-292-9336FF.indb 4 7/16/2018 9:07:56 AM

5

Mounting (Rack)

2U

3U

2

Secure the shelves

B

to the mounting rails permanently using the included screws

and cup washers

C

as shown.

• For 2U equipment mounting, place 4 screws total at the front and 4 screws total

at the back.

• For 3U equipment mounting, place 6 screws total at the front and 4 screws total

at the back.

Tighten all screws before proceeding.

Warning: Do not attempt to install equipment until you have inserted and

tightened the required screws. The plastic pegs will not support the weight

of your equipment.

2

C

B

18-05-292-9336FF.indb 5 7/16/2018 9:07:57 AM

6

Mounting (Rack)

3U2U

3

Using the included hardware, attach the mounting brackets to the forward mounting

holes of the cabinet. The mounting bracket "ears" should face forward. (Some

equipment may have pre-installed or integral mounting brackets.)

3

4

With the aid of an assistant (if necessary), lift your equipment and slide it into the

shelves. Attach the equipment mounting brackets to the forward mounting rails with

user-supplied screws and washers

D

. Tighten all screws securely.

3U

2U

4

D

18-05-292-9336FF.indb 6 7/16/2018 9:07:59 AM

7

2-Post (Telecom) Mounting

Select external battery pack models include the hardware required for 2-post mounting.

If this hardware did not come with your unit, a 2-Post Rackmount Installation Kit (Model

2POSTRMKITWM or 2POSTRMKITHD) may be ordered separately. Refer to the

illustrations below for specific installation instructions covering 2U, 3U and 4U battery

packs.

Important: Illustrations show the most typical installation configurations; your

model may vary. Use only the pre-drilled screw holes to attach mounting

brackets to the sides of the battery pack. When installing battery packs into the

rack, ensure the weight of the unit is evenly distributed.

2U

1

X 8

2U

2

X 4

3

X 2 X 2 X 2

3U

4U

X 8

X 4

Mounting (Rack)

X 8

X 4

1

2

3

18-05-292-9336FF.indb 7 7/16/2018 9:08:01 AM

8

BP24V15RT2U 4-Post Mounting

To install an external battery pack in a 4-post rack, remove the mounting hole covers

from the top and bottom sides of the battery pack

1

. To install the battery pack in a

4-post rack, attach the mounting ears to each side of the UPS using the included

hardware

2

. With the help of an assistant, lift the battery pack and attach it to a

standard rack with user-supplied hardware

3

.

Mounting (Rack)

3

1 2

18-05-292-9336FF.indb 8 7/16/2018 9:08:03 AM

9

BP24V15RT2U 2-Post Mounting

To install the external battery pack in a 2-post rack, remove the mounting hole covers

from the top and bottom sides of the pack

1

. Attach the mounting ears to each side of

the UPS using the included hardware

2

. With the help of an assistant, lift the battery

pack and attach it to a standard rack with user-supplied hardware

3

.

Mounting (Rack)

3

1 2

Important: Illustrations show the most common installation

configurations; your model may vary. Use only the pre-drilled screw holes

to attach mounting brackets to the sides of the battery pack. When

installing battery packs into the rack, ensure the weight of the unit is

evenly distributed.

18-05-292-9336FF.indb 9 7/16/2018 9:08:03 AM

10

Select external battery pack models support tower

mounting. For increased stability, Tripp Lite

recommends the use of the 2-9USTAND (sold

separately). Ensure the Battery Orientation Warning

label is not facing upward when installing the

battery pack in tower orientation. Follow the

instructions included with the 2-9USTAND to

complete the installation.

Mounting (Tower)

WARNING

DO NOT INSTALL PRODUCT

WITH THIS LABEL

FACING UP

BP24V15RT2U Tower Mounting

The BP24V15RT2U will stand in a tower position without the aid of the included

hardware. For increased stability, Tripp Lite recommends removing the screw covers

from each bottom side

1

and attaching the included hardware

2

. In either position,

the user must determine the fitness of hardware and procedures before installation.

1 2

NOTICE: If Battery Orientation Warning labels are affixed to both sides of

the battery pack, it can only support rack-mount installation.

18-05-292-9336FF.indb 10 7/16/2018 9:08:04 AM

11

1

Select battery packs have a polarized plug

A

on an output cord permanently connected to

the rear panel. Simply plug the output cord

directly into the UPS external battery

connector (refer to the UPS manual for

external battery connector description and

location).

Note: Only one of these battery packs is generally

connected to a UPS at one time. For longer

runtime, use one or more Tripp Lite Battery Packs

with daisy-chain capability.

2

Select battery packs feature daisy-chain

capability for longer runtime

B

. To connect to

a UPS, insert one end of the attached cable

C

into either plug on the rear of the battery

pack and the cable’s other end into the

external battery connector of your UPS.

(See your UPS manual for external battery

connector description and location.) To

Connection

A

B

C

1

2

3

connect multiple battery packs to a single UPS for greatly increased runtime,

connect the output of the first battery pack to the UPS system's external battery

connector, then “daisy-chain” the others: connect an input/output plug on the

second battery pack to an input/output plug on the first, a plug on the third to a

plug on the second and so on.

Note: Multiple battery pack arrays will provide longer runtimes, but will also require longer

recharge times.

3

Select battery packs contain an external battery detection port on the rear panel.

The battery packs should only be used with host UPS models that provide the same

functionality. The UPS will automatically detect the external battery upon connection

with the battery communication cable

D

. Check the UPS manual for compatible

external battery pack models, configuration requirements and potential limitations.

Battery packs are for use only with UPS systems supporting external battery pack

detection cabling (this connection is not required if the UPS does not support this

feature).

D

Battery

Pack

UPS

18-05-292-9336FF.indb 11 7/16/2018 9:08:05 AM

12

Maintenance

Battery packs require no maintenance but should be kept dry at all times. Avoid

installation in locations with high heat and/or humidity. The battery packs should be kept

fully charged by being connected to an active UPS system, not left in a depleted

condition. Batteries left in a discharged state will suffer a permanent loss of capacity.

Troubleshooting

There is a fuse array inside the battery packs. If a heavy overload or short circuit is

encountered, a fuse will open (blow). A battery pack with a blown fuse will deliver no

output voltage at any load. A qualified technician must replace the fuses. Contact Tripp

Lite Customer Support for additional information.

Internal Battery Replacement

The batteries in the battery packs will eventually wear out and be unable to provide

adequate backup times. The batteries should only be replaced by factory authorized

service personnel. Tripp Lite offers an exchange program for North American customers

wherein they may exchange worn-out battery packs for new ones at a price comparable

to the cost of individual battery replacement. For more details, visit

www.tripplite.com/support.

Storage

Disconnect your battery pack’s power cable before storing. If you plan to store your

battery pack for an extended period of time, fully recharge its batteries every three

months by connecting it to a UPS that is connected to AC input for at least 12 hours.

Service

Your Tripp Lite product is covered by the warranty described in this manual. A variety of

Extended Warranty and On-Site Service Programs are also available from Tripp Lite. For

more information on service, visit www.tripplite.com/support. Before returning your

product for service, follow these steps:

1. Review the installation and operation procedures in this manual to insure that the

service problem does not originate from a misreading of the instructions.

2. If the problem continues, do not contact or return the product to the dealer. Instead,

visit www.tripplite.com/support.

3. If the problem requires service, visit www.tripplite.com/support and click the Product

Returns link. From here you can request a Returned Material Authorization (RMA)

number, which is required for service. This simple on-line form will ask for your unit’s

model and serial numbers, along with other general purchaser information. The RMA

number, along with shipping instructions will be emailed to you. Any damages

(direct, indirect, special or consequential) to the product incurred during shipment to

Tripp Lite or an authorized Tripp Lite service center are not covered under warranty.

Products shipped to Tripp Lite or an authorized Tripp Lite service center must have

transportation charges prepaid. Mark the RMA number on the outside of the

package. If the product is within its warranty period, enclose a copy of your sales

receipt. Return the product for service using an insured carrier to the address given

to you when you request the RMA.

18-05-292-9336FF.indb 12 7/16/2018 9:08:05 AM

13

2-Year Limited Warranty

Seller warrants this product, if used in accordance with all applicable instructions, to be free from original

defects in material and workmanship for a period of 2 years from the date of initial purchase. If the product

should prove defective in material or workmanship within that period, Seller will repair or replace the product, at

its sole discretion.

THIS WARRANTY DOES NOT APPLY TO NORMAL WEAR OR TO DAMAGE RESULTING FROM ACCIDENT, MISUSE,

ABUSE OR NEGLECT. SELLER MAKES NO EXPRESS WARRANTIES OTHER THAN THE WARRANTY EXPRESSLY SET

FORTH HEREIN. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ALL IMPLIED WARRANTIES,

INCLUDING ALL WARRANTIES OF MERCHANTABILITY OR FITNESS, ARE LIMITED IN DURATION TO THE WARRANTY

PERIOD SET FORTH ABOVE; AND THIS WARRANTY EXPRESSLY EXCLUDES ALL INCIDENTAL AND CONSEQUENTIAL

DAMAGES. (Some states do not allow limitations on how long an implied warranty lasts, and some states do not

allow the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions

may not apply to you. This warranty gives you specific legal rights, and you may have other rights which vary

from jurisdiction to jurisdiction).

WARNING: The individual user should take care to determine prior to use whether this device is suitable,

adequate or safe for the use intended. Since individual applications are subject to great variation, the

manufacturer makes no representation or warranty as to the suitability or fitness of these devices for any specific

application.

Product Registration

Visit www.tripplite.com/warranty today to register your new Tripp Lite product. You’ll be automatically entered into

a drawing for a chance to win a FREE Tripp Lite product!*

* No purchase necessary. Void where prohibited. Some restrictions apply. See website for details.

Tripp Lite has a policy of continuous improvement. Specifications are subject to change without notice.

Warranty and Product Registration

1111 W. 35th Street Chicago, IL 60609 USA • www.tripplite.com/support

18-05-292-9336FF.indb 13 7/16/2018 9:08:05 AM

14

Manual del propietario

1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support

Introducción 15

Instrucciones de seguridad importantes 15

Montaje 17

Conexión 24

Mantenimiento 25

Garantía 26

English 1

Français 27



 40

Bancos de batería

externas Serie BP

No conveniente para los usos móviles.

Módulos de Baterías

de 24V

Módulos de Bat-

erías de 36V

Módulos de Baterías

de 48V

Módulos de Baterías

de 72V

BP24V15RT2U, 14AH

BP24V28-2U, 28AH

BP24V36-2US, 36AH

BP24V70-3U, 70AH

BP36V15-2U, 18AH

BP36V42-3U, 21AH

BP48V24-2U, 18AH

BP48V27-2US, 27AH

BP48V60RT-3U, 42AH

BP72V15-2U, 15AH

BP72V18-2US, 18AH

BP72V28RT-3U, 28AH

18-05-292-9336FF.indb 14 7/16/2018 9:08:06 AM

15

Introducción

Instrucciones de seguridad importantes

Los bancos de baterías externas Serie BP de Tripp Lite están diseñados para usarse con

diferentes UPS de Tripp Lite equipados con conectores para bancos externos de baterías.

GUARDE ESTAS INSTRUCCIONES

¡ADVERTENCIA! Los anaqueles de montaje no están diseñados para

soportar más de un banco de baterías. No apile múltiples bancos en un

sólo juego de anaqueles. El incumplimiento de esta advertencia puede

originar daños al producto o lesiones personales.

•

Sea precavido al levantar bancos de baterías. Debido a su gran peso, se requieren

por lo menos dos personas para ayudarlo a levantar e instalar dichos bancos.

• Asegúrese que sus bancos de baterías y su UPS usen el mismo voltaje de

corriente continua antes de conectarlos.

• Use solo módulos de baterías externas Tripp Lite con protección contra

sobrecorriente. La instalación debe llevarla a cabo únicamente personal de

servicio calificado. Póngase en contacto con Soporte al Cliente de Tripp Lite al

773.869.1234 para consultar el módulo de baterías externas apropiado que

se debe conectar.

• Los gabinetes metálicos de sus baterías externas están provistos por

seguridad de un medio de protección equipotencial. Al usar baterías externas

con conector de 2 pines, asegúrese de unir el gabinete metálico de su batería

externa al gabinete metálico del sistema UPS. Los módulos de baterías con

tres conductores / pines están equipados con una clavija de conexión a tierra.

Los gabinetes de plástico no requieren bonding. Para los requisitos de la cinta

de conexión a tierra, consulte abajo:

Módulos de Baterías de 24V

BP24V15RT2U: Gabinete de plástico, por lo que no se requiere Cinta de

conexión a tierra.

BP24V28-2U: Cinta de conexión a tierra 12 AWG

BP24V36-2US: Cinta de conexión a tierra 12 AWG

BP24V70-3U: Cinta de conexión a tierra 12 AWG

Módulos de Baterías de 36V

BP36V15-2U: Cinta de conexión a tierra 12 AWG

BP36V42-3U: Cinta de conexión a tierra 12 AWG

Módulos de Baterías de 48V

BP48V24-2U: Cinta de conexión a tierra 12 AWG

BP48V27-2US: Cinta de conexión a tierra 12 AWG

BP48V60RT-3U: Cinta de conexión a tierra 12 AWG

Nota: El conector de la batería en módulos de baterías de 72V tiene incorporada un clavija

para conexión a tierra, de modo que no se requiere una cinta adicional para conexión a tierra.

18-05-292-9336FF.indb 15 7/16/2018 9:08:06 AM

16

Instrucciones de seguridad importantes

Fija firmemente la Cinta de conexión a tierra suministrada al sistema UPS

como se ilustra a continuación:

• El uso de este equipo en aplicaciones de soporte de vida en donde la falla de

este equipo pueda razonablemente hacer suponer que causará fallas en el

equipo de soporte de vida o afecte significativamente su seguridad o

efectividad, no está recomendado. No use este equipo en la presencia de una

mezcla anestésica inflamable con aire, oxigeno u óxido nitroso.

• Los procedimientos de montaje recomendados son para tipos de bastidores comunes

y pueden no ser apropiados para todas las configuraciones de bastidor. El usuario

debe determinar la idoneidad del bastidor, de los accesorios para el montaje en

pared y de los procedimientos, antes del montaje.

• Cuando se conectan varios bancos de baterías a un sólo UPS, estos deben tener

aproximadamente la misma antigüedad.

• Es normal que se produzcan chispas al conectar baterías externas.

• No desconecte las baterías externas del UPS mientras éste se encuentra en

operación con energía de batería, debido a que puede formarse un arco peligroso.

• Debido a que las baterías presentan un peligro de choque eléctrico y quemaduras

por las altas corrientes de cortocircuito, tome las precauciones adecuadas. No

deseche las baterías en un incinerador. No abra las baterías. No ponga los

terminales de la batería en corto o en puente con ningún objeto. Apague y

desconecte el UPS antes de reemplazar la batería. Sólo debe cambiar las baterías

personal técnico debidamente capacitado. Use herramientas con mangos aislados y

reemplace las baterías existentes con el mismo número y tipo de baterías nuevas

(plomo-ácido selladas). Las baterías del UPS son reciclables. Consulte la

reglamentación local para los requisitos de disposición de desechos o visita

http://www.tripplite.com/support/recycling-program para reciclar información. Tripp Lite

ofrece una línea completa de Cartuchos de reemplazo de batería para UPS (R.B.C.).

Visite Tripp Lite en la web en http://www.tripplite.com/products/battery-finder/ para

localizar la batería de reemplazo específica para su UPS.

18-05-292-9336FF.indb 16 7/16/2018 9:08:06 AM

17

Montaje (Bastidor)

Monte su banco de baterías en un bastidor de 2 o 4 postes (vea la página 15] para

instalación de 2 postes). El usuario debe determinar la idoneidad de los materiales y

accesorios, así como de los procedimientos antes del montaje. Si los materiales y

procedimientos no son adecuados para su aplicación, contacte con el fabricante de su

bastidor. Los procedimientos descritos en este manual son para bastidores comunes y

de tipo caja y podrían no ser apropiados para todas las aplicaciones.

Montaje de 4 postes

La mayoría de los módulos de baterías externas incluyen el hardware requerido para su

instalación en 4 postes. Si este hardware no venía con su unidad, un Juego Ajustable

para Instalación en Rack de 4 postes (Modelo 4POSTRAILKIT) puede ser solicitado, por

separado.

1

Los ganchos plásticos

A

incluidos mantendrán temporalmente los estantes

rackmount vacíos

B

mientras usted coloca los accesorios de instalación

permanentes. Inserte un gancho cerca del centro del soporte frontal y posterior de

cada estantes como se muestra. (Cada soporte frontal tiene 6 orificios y cada

soporte posterior posee 3 orificios.) Los ganchos encajarán en su lugar.

Después de colocar los ganchos, expanda cada estante para que se ajuste con la

profundidad de los rieles de su rack. Los ganchos encajarán en los orificios

cuadrados en los rieles del rack para sostener los estantes. Consulte las etiquetas

de la unidad del rack para confirmar que los estantes estén nivelados en todas las

direcciones.

Nota: El reborde de soporte de cada estante debe quedar mirando hacia adentro.

B

1

A

18-05-292-9336FF.indb 17 7/16/2018 9:08:06 AM

18

Montaje (Bastidor)

2U

3U

2

Asegure de manera permanente los estantes

B

a los rieles de montaje usando los

tornillos incluidos y las arandelas acopadas

C

como se muestra.

• Para montaje de equipos de 2U, coloque 4 tornillos en total en la parte frontal y

4 tornillos en total en la parte posterior.

• Para montaje de equipos de 3U, coloque 6 tornillos en total en la parte frontal y

4 tornillos en total en la parte posterior.

Apriete todos los tornillos antes de continuar.

Advertencia: No intente instalar su equipo hasta que haya insertado y

apretado los tornillos necesarios. Los ganchos plásticos no soportarán el

peso de su equipo.

2

C

B

18-05-292-9336FF.indb 18 7/16/2018 9:08:07 AM

19

Montaje (Bastidor)

3U2U

3

Coloque los soportes de montaje de su equipo en los orificios de montaje

delanteros del gabinete usando los accesorios que vienen incluidos con su equipo.

Las “orejas” del soporte de montaje deben quedar mirando hacia adelante. (Puede

que algunos equipos tengan soportes de montajes preinstalados o integrados.)

3

4

Con la ayuda de un asistente (en caso de ser necesario), levante su equipo y

deslícelo en los estantes. Coloque los soportes de montaje del equipo en los rieles

de montaje delanteros con los tornillos y arandelas

D

suministradas por el

usuario. Apriete todos los tornillos de manera segura.

3U

2U

4

D

18-05-292-9336FF.indb 19 7/16/2018 9:08:08 AM

20

Montaje de 2 postes (Telecomunicaciones)

Para instalar módulos de baterías para rack, en racks de 2 postes, se requiere un Juego

para Instalación en Rack de 2 postes de Tripp Lite (Modelo 2POSTRMKITWM o

2POSTRMKITHD). Si este Juego no venía con su unidad, puede ser solicitado, por

separado. Refiérase a la ilustración de abajo para instrucciones especificas de

instalación que abarca a los módulos de baterías 2U, 3U y 4U.

Importante: Las ilustraciones muestran las configuraciones de instalación más

típicas; su modelo puede variar. Use solamente los agujeros, para los tornillos,

preperforados para fijar las abrazaderas a los lados del módulo de baterías.

Cuando instale el módulo de baterías en el rack, asegúrese que el peso de la

unidad esté uniformemente distribuido.

2U

1

X 8

2U

2

X 4

3

X 2 X 2 X 2

3U

4U

X 8

X 4

Montaje (Bastidor)

X 8

X 4

1

2

3

18-05-292-9336FF.indb 20 7/16/2018 9:08:09 AM

La page charge ...

Tripp Lite BP Series External Battery Packs Le manuel du propriétaire

Tripp Lite BP Series External Battery Packs Le manuel du propriétaire

dans d''autres langues

Documents connexes