Comelit IPPTZ110IRA Mode d'emploi

Catégorie
Des caméras de sécurité
Taper
Mode d'emploi
i
4" FULL-HD IP PTZ CAMERA
ART. IPPTZ110IRA
Before installation, please read the operation manual carefully
i
Contents
1. Introduction ........................................................................................................................................ 1
Features ......................................................................................................................................... 1
2. Hardware Installation ......................................................................................................................... 2
System requirement ....................................................................................................................... 2
Installation environment .................................................................................................................. 2
Installation environment requirements ..................................................................................... 2
Recommend operating environment ........................................................................................ 2
Connection instruction .................................................................................................................... 3
3. Operating Guide for Network High Speed Dome ................................................................................ 4
Set the IE Browser .......................................................................................................................... 4
Download and Install ActiveX.......................................................................................................... 4
Login .............................................................................................................................................. 7
Live view ........................................................................................................................................ 7
System specification setting ......................................................................................................... 11
System .................................................................................................................................. 11
Basic info ........................................................................................................................... 11
User manage ..................................................................................................................... 17
Serial ................................................................................................................................. 18
Record ............................................................................................................................... 19
Time zone .......................................................................................................................... 21
Micro-SD status ................................................................................................................. 22
AV ......................................................................................................................................... 23
Video channels .................................................................................................................. 23
Video parameters............................................................................................................... 24
Shot parameters ................................................................................................................ 25
Network ................................................................................................................................. 26
Ethernet ............................................................................................................................. 26
DDNS ................................................................................................................................ 27
Netport ............................................................................................................................... 28
Other protocol .................................................................................................................... 29
Alarm configuration ............................................................................................................... 30
Linkage .............................................................................................................................. 32
INPUT/OUTPUT alarm ...................................................................................................... 33
Motion ................................................................................................................................ 34
Local ..................................................................................................................................... 35
Local Settings .................................................................................................................... 35
Playback ....................................................................................................................................... 36
Search video and playback.................................................................................................... 36
4. Appendix .......................................................................................................................................... 37
Specification ................................................................................................................................. 37
Network Interface of Network High Speed Dome .......................................................................... 39
Default Network Parameters ......................................................................................................... 39
Frequently asked questions .......................................................................................................... 39
ii
CAUTION
Non-technician should not try to operate this high speed dome before reading this manual carefully. (This
manual are subject to change without prior notice.)
Cut the power supply off before operating the device to avoid damage caused by mal-operation.
Interior of the camera are precision optical and electrical instruments. Heavy pressure, shock and other
incorrect operations should be prevented. Otherwise, may cause damage to product.
Please do not use the product under circumstances where the limits exceed the maximum specified
temperature, humidity or power supply specifications.
Contents in this manual may be different from the edition that you are using. Should any unsolved problem
occur given that the product is used according to this manual, please contact our technical support
department or your product suppliers.
This manual content will be updated unscheduled, our company reserves the right to do manual contents
update without further notice.
The default username for this device is “admin”, and the password is blank. Default IP address is
192.168.1.188, HTTP port is 80.
PACKING LIST
Open the package, and check whether the accessories all contained.
Part Quantity
IP speed domeInclude bracket 1
Power supply 1
Screws bag 1
CD 1
Note:
When open the box, please check all of parts carefully, confirm the parts as same as packing list.
Please read the user manual carefully before the installation.
Make sure to turn off all the power when install the camera
Please confirm the power transformer, avoid the device damage with unmatched power source
Contact your local retailer without hesitate if anything is missing in your package.
1
1. Introduction
Features
Build in 10X optics zoom lens, up to 1080P 1~30FPS
True Day/Night switch
H.264 High Profile/MJPEG encoding, VBR/CBR, dual stream
Motion detection
Alarm linkage output, micro-SD card video recording, snapshot, FTP upload, e-mail notification, link Preset
ONVIF Profile S protocol,GB/T28181 protocol
360° horizonal continuous rotation; vertical 0°-90°, 255 Presets
Low power consumption – MTTF up to 30,000 hours
1CH alarm input, 1CH alarm output, build in micro-SD card slot, audio input/output, 100M Ethernet
IP66 protection level
2
2. Hardware Installation
System requirement
LAN or WAN Internet to connect server, via PC Ethernet (network card or network cable) TCP/IP
protocol connect, suggest Internet Explorer 9.0 version or later.
Monitor and PC configuration:
CPU: Dicaryon 2.8G or latter, RAM: 512M or later (above DirectX8.1)
Monitor: 17", 1920×1080 resolution
Operation system: Windows NT, Windows2000, Windows XP, Windows 7 or later
Installation environment
Installation environment requirements
Far away from high-temperature or humid environment, notice ventilation and avoid installing in shaky place.
Recommend operating environment
-20°C55°CThe camera will enable cold start below -20°C, then it will turn on the IR leds automatically and
operate normally after heating in 30 minutes)
Hardware installation steps
Please make sure LAN and WAN are working smoothly before the Network High Speed Dome installation. After
checked all the network system in good condition, keep your hands clean and dry, following the steps below.
Open the box to check the goods
Take out all goods which needed for installation
LAN connection
Use one network line to connect Speed Dome with concentrator or switchboard of the LAN. As Figure
below.
Users also can use one network line to connect IP Speed Dome with computer network card or
switchboard.
WAN connection
Use one network line to connect IP Speed Dome with router or XDSL Modem/Cable Modem.
router
web browser
switch
web browser
web browser
IP camera
IP cam
era
IP camera
3
Connect the power supply
After connect the power source, the IP speed camera will start operation automatically.
Connection instruction
Multi-function RJ45 line:
Analog video output
GND
Reset button
Power supply input24 VDC
RJ45
Alarm input
Alarm output
4
3. Operating Guide
Set the IE Browser
Because the high safety level of the IE browser, if you visit Network High Speed Dome for first time, please set
the IE browser.
Setting method: open the IE browser, click Internet Option into the "Security" page, click the "Custom Level", and
then follow steps to set the IE browser
Download and Install ActiveX
Users have to install ActiveX Control when visit Network High Speed Dome at the first time via IE browser.
Download and install the ActiveX:
Input the IP address (default address
http://192.168.1.188.) in Internet Explorer to enter into login page (users
can refer to the “NETWORK SETTINGS” under “SETUP” menu to set the configure the IP address).
5
At the login interface, click “downloadActiveX”. As Figure 3-1:
Figure 0-1
Notice the below download interface, click “Run”. As Figure 3-2:
Figure 0-2
A “User Account Control” interface will pop out, click “Yes” to install. As figure 3-3.
Figure 3-3
In download interface, you can also select “save” to save ActiveX in default storage file, such as
D:\TDDOWNLOAD.Then open the file an install the ActiveX. As figure 3-4 and 3-5.
6
Figure 3-4
Figure 3-5
Click “Install” in the below interface, as Figure 3-6:
Figure 3-6
Click “Finish” in the below interface to complete the installation, as Figure 3-7:
7
Figure 3-7
Login
Re-open Internet Explorer after ActiveX installation completes, input IP address ( http://192.168.1.188,) of the
Network High Speed then turn to login page, input username (default is admin) and password (default is
blank), click login to enter into main interface(see Figure 3-8):
Figure 0-8
Live view
Live preview interface as figure 3-9:
8
Figure 0-9
In the Live view interface, users can do remote operations such as master/slave stream video preview, voice
intercom, listen, video recording, full-screen preview, video capture, PTZ control, preset, area scan, pattern scan,
PTZ watch, preview video image volume adjustment, camera module parameters setting, etc.
Master/slave stream
notice the buttons at the left right corner, click it to switch
the preview mode.
Video capture: click icon to do screen video capture, it will create JPG picture and store in the
specified folder automatically. The default file storage path is C:\IPCamera\ , users can set it at the
Setting→→Local→→Local setting .
Full screen: click icon to get full screen preview, press ESC or right mouse click to exit full screen
preview.
Manual video: click icon to do manual video operation and store in the specified file automatically
(Video format is mp4, the default file storage path is C:\IPCamera\, users can set it at the
Setting→→Local→→Local setting .
Image parameters adjustment: users can adjust the image parameters at the video preview interface,
such as image brightness, hue, contrast, saturation and sharpness, etc. As Figure 3-10:
Figure 3-10
9
Day/Night switch: according to the surveillance need, users can set color mode, black/white mode, auto
mode. According to the environment need, users can set Day/night switch sensitivity 0-255, and
Night/day switch sensitivity 0-255. As Figure 3-11:
Figure 3-11
White balance: according to the environment color temperature, users can set the white balance, Auto
option for normal light environment, adjust the white balance value by drop down list selection
,
click
to save it. As Figure 3-9.
Image flip: via the buttons to adjust image flip, support horizontal flip , horizontal+vertical flip .
As Figure 3-9.
WDR: click to open it, click again to close it. As Figure 3-9.
Low illumination: click to open it, click again to close it. As Figure 3-9.
BLC: click to open it, click again to close it. As Figure 3-9.
3DNR: click to open it, click again to close it. As Figure 3-9.
Video formats
select the video format, 50HZ for PAL, 60HZ for NTSC. Click to save
it. As Figure 3-9.
Exposure compensation: select the exposure compensation at the drop down list, click
to save it. As Figure 3-9.
Exposure mode: select auto and handle at the drop down list, click to save it. As
Figure 3-9.
Max shutter: select the max shutter value at the drop down list, click to save it. As
Figure 3-9.
Min shutter: select the minimum shutter value at the drop down list, click to save it. As
Figure 3-9.
Max gain: select the gain value at the drop down list, click
to save it. As Figure 3-9.
10
Click PTZ at the video preview interface to turn to PTZ configuration interface. As
Figure 3-12:
Figure 3-12
PTZ control: user can do horizontal 360°/vertical 180°overall monitoring via PTZ configuration
buttons , PTZ operation speed 1-63 levels adjustable. As Figure 3-12.
Preset: adjust the camera to the appointed angle and location through directional buttons and then
select a preset number in the preset drop down list, click to set it. There are 1-255 presets can be
set, and users can click to delete the preset, click to call the preset. As Figure 3-12.
Area scan: via the PTZ buttons to set area scan, click to set left limit, click to set right limit
and area scan remembered automatically. When set the area scan, users have to select Small radian
scan (scan radian less then 180°) / Big radian scan (scan radian more then 180°) first and then set left
limit/right limit. Click to call area scan. As Figure 3-12.
Pattern scan: at the pattern scan drop down list, users can select the pattern scan number, and edit the
pattern scan name. Then click to start recording, click to stop recording, pattern scan
remembered automatically. Click to call pattern scan. As Figure 3-12.
PTZ Watch: at the PTZ Watch drop down list, users can select the PTZ watch type (Include preset, CRZ,
Pattern, Area, etc.) and set the idle time, then click to save it. As Figure 3-13.
11
Figure 3-13
CRZ: at the CRZ drop down list, users can select cruise preset, click to add preset, set the delay
time. Select preset ID and click to delete it. Finally click to save it, and Click to call
pattern scan. As Figure 3-14.
Figure 3-14
System specification setting
System
Basic info
System information
Click Setting System Basic info Sysinfo, IP Speed Dome “Device Info” interface. As figure 3-15:
12
Figure 0-15
Device name: Edit the camera name
Device number: Display the device serial number
Hardware version: Display the device hardware version number
UBOOT version: Display the product system UBOOT version number
Kernel version: Display the product system kernel version number
APP version: Display the product software version and the system version date
PTZ version: Display the IP speed dome version model
OCX version: Display the OCX version number
After setting complete, click to save it.
13
System operate
Click Setting System Basic info Sysoperate, IP Speed Dome “System operate” interface. As
figure 3-16:
Figure 3-16
Rest: Restore factory settings
Reboot: Click to do IP speed dome reboot operation
Parameters type: Select the parameters type which you have to derive
Parameter input: Select the configure file which you need and click
Parameter output: Select the configure file which you need and click
After setting complete, click to save it.
14
Update
Click Setting System Basic info Update, IP Speed Dome “Update” interface. As figure 3-17:
Figure 3-17
System update: System update online.
Operation method:
Click , find the specified file and select the upgrade package, click
or double click to operate the program file . As Figure below:
Click , system upgrade automatically;
15
After system upgrade successfully, the following window will pop out, click .
As Figure below:
Reopen the IE browser and input the IP address, after log in, check the whether the
software version is updated.
Note: after system upgrade successfully, you need to reset camera data in "Sysoperate", clear IE cache and
install ActiveX again before logging in web system (clear IE cache as figure below).
Non-professional technicians do not operate the system upgrade.
Please do not power off during installing update.
16
Log query
Log query setting, as Figure 3-18:
Figure 3-18
Type: Select the alarm log type, there are alarm/ exception/ operation/ information selectable
Begin time/ End time: Set the log search time period, click icon , and the log information will
display, click to open or download the corresponding log information
After setting complete, click to save it.
17
User manage
User manage, as Figure 3-19:
Figure 3-19
Add User: Add a new users, and select the new user limits of authority
Modify: Select the added user and modify the users password
Del User: Delete the added users
After setting, click to save it.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72
  • Page 73 73
  • Page 74 74
  • Page 75 75
  • Page 76 76
  • Page 77 77
  • Page 78 78
  • Page 79 79
  • Page 80 80
  • Page 81 81
  • Page 82 82
  • Page 83 83
  • Page 84 84
  • Page 85 85
  • Page 86 86
  • Page 87 87
  • Page 88 88
  • Page 89 89
  • Page 90 90
  • Page 91 91
  • Page 92 92
  • Page 93 93
  • Page 94 94
  • Page 95 95
  • Page 96 96
  • Page 97 97
  • Page 98 98
  • Page 99 99
  • Page 100 100
  • Page 101 101
  • Page 102 102
  • Page 103 103
  • Page 104 104
  • Page 105 105
  • Page 106 106
  • Page 107 107
  • Page 108 108
  • Page 109 109
  • Page 110 110
  • Page 111 111
  • Page 112 112
  • Page 113 113
  • Page 114 114
  • Page 115 115
  • Page 116 116
  • Page 117 117
  • Page 118 118
  • Page 119 119
  • Page 120 120
  • Page 121 121
  • Page 122 122
  • Page 123 123
  • Page 124 124
  • Page 125 125
  • Page 126 126
  • Page 127 127
  • Page 128 128
  • Page 129 129
  • Page 130 130
  • Page 131 131
  • Page 132 132
  • Page 133 133
  • Page 134 134
  • Page 135 135
  • Page 136 136
  • Page 137 137
  • Page 138 138
  • Page 139 139
  • Page 140 140
  • Page 141 141
  • Page 142 142
  • Page 143 143
  • Page 144 144
  • Page 145 145
  • Page 146 146
  • Page 147 147
  • Page 148 148
  • Page 149 149
  • Page 150 150
  • Page 151 151
  • Page 152 152
  • Page 153 153
  • Page 154 154
  • Page 155 155
  • Page 156 156
  • Page 157 157
  • Page 158 158
  • Page 159 159
  • Page 160 160
  • Page 161 161
  • Page 162 162
  • Page 163 163
  • Page 164 164
  • Page 165 165
  • Page 166 166
  • Page 167 167
  • Page 168 168
  • Page 169 169
  • Page 170 170
  • Page 171 171
  • Page 172 172
  • Page 173 173
  • Page 174 174
  • Page 175 175
  • Page 176 176

Comelit IPPTZ110IRA Mode d'emploi

Catégorie
Des caméras de sécurité
Taper
Mode d'emploi