FireMagic Aurora Power Burner Manuel utilisateur

1

INSTALLER: Leave these instructions with consumer.

CONSUMER:

Retain for future reference.

INSTALLATION AND

OWNER'S MANUAL

Important: READ THESE INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION

DANGER

IF YOU SMELL GAS:

1. Shut off the gas to the appliance.

2. Extinguish any open ﬂame.

3. Open cover.

4. If odor continues, keep away from the

appliance, and immediately call your

gas supplier or ﬁre department.

WARNING

1. Do not store or use gasoline or other

ﬂammable vapors and liquids in the

vicinity of this or any other appliance.

2. A propane cylinder not connected for use

shall not be stored in the vicinity of this

or any other appliance.

CODE AND SUPPLY REQUIREMENTS: This

appliance must be installed in accordance with

local codes and ordinances, or, in the absence

of local codes, with either the latest National

Fuel Gas Code (ANSI Z223.1/NFPA 54), and

Natural Gas and Propane Storage and Handling

Installation Code (CSA-B149.1).

This appliance and its individual shutoff valves

must be disconnected from the gas supply piping

system when testing the system at pressures in

excess of ½ psig (3.5 kPa).

This appliance must be isolated from the gas

supply piping system by closing its individual

manual shutoff valves during any pressure

testing of the gas supply system at pressures

up to and including ½ psig (3.5 kPa).

All electrical outlets in the vicinity of the appliance

must be properly grounded in accordance with local

codes or, in the absence of local codes, with the

National Electrical Code, ANSI/NFPA 70, or the

Canadian Electrical Code, CSA C22.1, whichever

is applicable.

Keep all electrical supply cords and fuel supply

hoses away from any heated surface.

WARNING

Improper installation, adjustment, alteration,

service, or maintenance can cause injury or

property damage. Refer to this manual. For

assistance or additional information consult

a qualiﬁed professional service technician,

service agency, or the gas supplier.

Certiﬁed to: ANSI Z21.58

CSA 1.6

Robert H. Peterson Co. • 14724 East Proctor Avenue • City of Industry, CA 91746

GETTING STARTED

WARNINGS AND SAFETY CODES

US

®

C

L-C2-449

REV 4 - B - 2006140955

POWER BURNER

19-7B Series

ONLY TO BE USED OUTDOORS

2

DANGER:

SI VOUS SENTEZ LE GAZ :

1. Coupez l’admission de gaz de I’appariel.

2. Éteindre toute ﬂamme nue.

3. Ouvrir le couvercle.

4. Si l’odeur persiste, éloignez-vous de

l’appareil et appelez immédiatement

le fournisseur de gaz ou le service

d’incendie.

AVERTISSEMENT:

1. Ne stockez pas ou n’employez pas

l’essence ou d’autres vapeurs et liquides

inﬂammables à proximité de ceci ou

d’aucun autre appareil.

2. Un cylindre de propane non relié pour

l’usage ne sera pas stocké à proximité

de ceci ou d’aucun autre appareil.

CONDITIONS DE CODE ET D’APPROVISIONNEMENT:

Ce gril doit être installé selon des codes et des ordonnances

locaux, ou, en l’absence des codes locaux, avec l’un ou l’autre

le plus défunt Code national de gaz de carburant (norme ANSI

Z223.1/NFPA 54), et Stockage de gaz naturel et de propane

et manipulation du code d’installation (CSA-B149.1).

Cet appareil et ses différents robinets d’isolement doivent être

démontés du gaz-fournissent le système sifﬂant en examinant

le système aux pressions au-dessus du ½ psig (kPa 3.5).

Cet appareil doit être isolé dans gaz-fournissent le système

siant par fermeture que ses diérents robinets d’isolement

manuels pendant tous les essais sous pression du gaz-

fournissent le système aux pressions jusques et y compris

le ½ psig (kPa 3.5).

Toutes les sorties électriques à proximité du gril doivent être

correctement fondues selon des codes locaux, ou en l’absence

de local code, avec le code électrique national, ANSI/NFPA

70, ou le code électrique canadien, CSA C22.1, celui qui est

applicable.

Maintenez tout électrique-fournissent des cordes et carburant-

fournissent des tuyaux partis de n’importe quelle surface de

chauffage.

INSTALLATEUR : Laissez ces instructions avec le consommateur.

CONSOMMATEUR : Maintenez pour la future référence.

AVERTISSEMENT:

L’installation inexacte, l’ajustement, le

changement, le service, ou l’entretien

peuvent causer des dommages ou des

dégats matériels. Référez-vous à ce manuel.

Pour de l'aide ou des renseignements

supplémentaires, consultez un technicien

professionnel qualifié de service, une

agence de service ou le fournisseur de gaz.

• Ce gril est pour ultilisation à l’extérieur seulement.

Si l’appareil est entreposé à l’intérieur, enlever les

bouteilles et les laisser à l’extérieur.

• Ne pas ranger le gril immédiatement aprés l’avoir utilisé.

le laisser refroidir avant de le déplacer ou de la ranger.

Le non respect de cette mesure de sécurité pourrait

entraîner un incendie causant des dommages à la

propriété, des blessures ou la mort.

• Ne pas utiliser cet appareil sous une surface combustible.

• Ne pas utiliser cet appareil sous un auvent. Le non

respect de cette mesure de sécurité pourrait entraîner

un incendie ou des blessures.

• Dégagement minimal entre les parois latérales et l’arriére

de l’appareil et la construction combustible (45.7 cm à

partir des parois latérales et 45.7cm à partir de l’arriére).

• Le régulareur de pression de gaz prévu avec cet appareil

de cuisson à gaz pour l’extérieur doit être utilisé. Ce

régulateur est réglé pour une pression de sortie de 5

pouces de colonne de l’eau pour le gaz naturel, et 10

pouces pour le propane.

• LE RÉGULATEUR INCLUS D’APPAREILS EST ÉVALUÉ

POUR LE MAXIMUM DE 1/2 (LIVRES PAR POUCE

CARRÉ). SI VOTRE OFFRE DE GAZ EST 1/2 PLUS

GRAND QUE (LIVRES PAR POUCE CARRÉ), UN

RÉGULATEUR ADDITIONNEL DOIT ÊTRE INSTALLÉ

AVANT LE GRIL. VOIR LA SECTION DE CONDITIONS

D’OFFRE DE GAZ POUR LA PRESSION APPROPRIÉE

D’OFFRE DE GAZ.

• Ne couvrez jamais la surface entière de cuisine ou de

gril de gauffreuses ou de casseroles. La surchauffe se

produira et les brûleurs ne seront pas très performants

quand la chaleur de combustion est emprisonnée au-

dessous de la surface à cuire.

• Ne pulvérisez jamais l’eau sur une unité chaude de gaz,

comme ceci peut endommager des composants de

porcelaine ou de fer de fonte.

• Une fuite de GPL peut causer une incendie ou une

explosion si enflammée entraînant des blessures

corporelles graves ou la mort.

• Communiquez avec le fournisseur de GPL pour les

réparations ou pour disposer de qules bouteille ou du

GPL non utilisé.

DANS LE CONTRE- POWER BURNER

INSTALLATION INSTRUCTIONS ET MANUEL DU PROPRIÉTAIRE

Certiﬁé à la norme: ANSI Z21.58

CSA 1.6

SÛRETÉ ET CODES D’AVERTISSEMENT

À UTILISER UNIQUEMENT À L'EXTÉRIEUR

L-C2-449

REV 4 - B - 2006140955

3

CONTENTS

L-C2-449

REV 4 - B - 2006140955

GETTING STARTED

INSTALLATION, OPERATION, AND SAFETY

INFORMATION ��4

ELECTRICAL CONNECTIONS ��4

GAS SAFETY INFORMATION ��5

WARNING ��5

WHEN USING PROPANE GAS ��5

WHEN USING NATURAL GAS �� 5

INSTALLATION SAFETY GUIDELINES �� 5

OPERATING THE UNIT SAFELY AND CORRECTLY ��5

SAFE USE & MAINTENANCE OF PROPANE GAS

CYLINDERS �� 7

ENCLOSURE / VENTILATION REQUIREMENTS ��8

ENCLOSURE �� 9

WHEN A PROPANE (L.P.) CYLINDER IS USED IN THE

ENCLOSURE

�� 9

INSTALLATION REQUIREMENTS ��10

OVERHEAD CONSTRUCTION AND EXHAUST HOOD

REQUIREMENTS

�� 10

REAR WALL CLEARANCES �� 11

BACKSPLASH CLEARANCE (if applicable) ��11

SIDE WALL / CORNER WALL CLEARANCES

(if applicable)

�� 11

CONTROL PANEL CLEARANCES ��12

COMBUSTION AIR AND COOLING AIRFLOW ��12

GAS-SUPPLY PLUMBING REQUIREMENTS ��12

ELECTRICAL SAFETY ��13

MODEL SPECIFICATIONS ��14

COUNTERTOP OVERHANG ��15

ENCLOSURE VENTILATION �� 15

RECOMMENDED OFFSET INSTALL �� 16

SUBSTRATE ��16

WIRING DIAGRAM ��17

PARTS LIST ��18

INSTALLATION

INSTALLATION �� 19

COUNTER PREPARATION �� 19

CONNECT THE GAS SUPPLY �� 19

POWER SUPPLY & WIRE HARNESS CONNECTIONS �� 20

SLIDE UNIT INTO ENCLOSURE �� 24

INSTALL THE COOKING GRID �� 24

INSTALL THE POWER BURNER LID �� 24

USE, CARE, & SERVICE

IDENTIFICATION OF CONTROLS �� 25

USING THE APPLIANCE �� 26

LIGHTING (IGNITION) INSTRUCTIONS �� 27

ELECTRONIC LIGHTING �� 27

MANUAL LIGHTING�� 27

SHUTTING OFF THE UNIT �� 27

SERVICING AND CLEANING �� 29

CLEANING YOUR POWER BURNER �� 29

CONTROL PANEL REMOVAL �� 31

INTERIOR PROTECTION PLATE REMOVAL �� 32

FLAME COLLIMATOR REMOVAL �� 32

BURNER REMOVAL�� 32

SYSTEM RESET �� 32

CONVERT GAS TYPE / CHECK BURNER ORIFICES �� 33

NOTES PAGE �� 36

TROUBLESHOOTING �� 37

WARRANTY �� 38

4

1. The outdoor appliance and surrounding area MUST

remain clear of ﬂammable substances such as gasoline,

yard debris, wood, etc. Maintain a minimum horizontal

clearance of 18" (in all directions) from combustible

materials/items.

2. Do not block the 1" front air inlet along the bottom of

the control panel. See the COMBUSTION AIR AND

COOLING AIRFLOW section under INSTALLATION

REQUIREMENTS for details.

3. This unit must be installed so that the required

vent openings and surrounding area of the

enclosure remain clear and free at all times. See

the ENCLOSURE/VENTILATION REQUIREMENTS

section for details.

4. When using propane gas: the propane cylinder,

regulator, and rubber hose must be in a location

not subject to temperatures above 125° F (51° C).

5. Do not operate the burner with the cover in place.

6. The ﬂames on each burner burn evenly along the

entire burner with a steady ﬂame (mostly blue). If

burner ﬂames are not normal, check and clean the

oriﬁce and burner/venturi tubes for insects and insect

nests. A clogged tube can lead to a ﬁre beneath the

unit. A proper ﬂame pattern will ensure safe operation

and optimal performance. Adjust the air shutter as

needed (see AIR SHUTTER ADJUSTMENT section).

7. The in-line gas valve or gas cylinder valve must always

be shut OFF when the unit is not in use.

8. Whenever reconnecting any wires, apply a small

amount of dielectric grease to the male connector,

then make the connection. This will ensure conductivity

and prevent moisture from affecting the contact.

9. Wear gloves and use extreme caution whenever

installing and handling this product and its accessories

as certain components have sharp edges that can

cause personal injury.

WARNING: NEVER cover more than 75% of the cooking surface with griddles or pans. Overheating will occur,

and burners will not perform properly when combustion heat is trapped below the cooking surface.

IMPORTANT

IN THE EVENT OF A GREASE FIRE, IMMEDIATELY SHUT OFF THE MAIN GAS VALVE TO THE UNIT. ALLOW THE FIRE

TO EXTINGUISH ITSELF. KEEP AT A SAFE DISTANCE. A THOROUGH INSPECTION BY A QUALIFIED PROFESSIONAL

SERVICE TECHNICIAN SHOULD BE CONDUCTED BEFORE FUTURE USE OF YOUR UNIT. THE SERVICE TECHNICIAN

WILL CHECK THE SYSTEM FOR GAS LEAKS AND WILL CHECK ALL ELECTRICAL WIRING FOR DAMAGE. ALL

GAS LEAKS AND WIRING MUST BE REPAIRED PRIOR TO FUTURE USE.

ELECTRICAL CONNECTIONS

A 120VAC (15 AMP minimum) GFCI GROUNDED 3-wire receptacle (not included) is required within

the vicinity of the unit to provide power to it. The GFCI receptacle must be a WEATHER-PROOF IN-USE

COVERED RECEPTACLE.

• Observe the National Electric Code and all local codes.

• Verify proper polarity of the receptacle.

• If an extension cord is used, ensure it is a 3-wire GROUNDED cord that is rated for the power of the

equipment, and is approved for outdoor use with a W-A marking. DO NOT use 2-prong adapters.

• DO NOT TAMPER WITH THE EXTENSION CORD OR THE UNIT POWER-SUPPLY CORD.

Important: ONLY REPLACE THE INTERIOR OVEN LIGHTS WITH 12V / 10 WATT HALOGEN BULB(S).

CAUTION: FOR YOUR SAFETY, you must provide openings in the enclosure for replacement air

and ventilation (in case of possible leakage from gas connections or propane cylinders).

Failure to do so may result in a ﬁre or explosion causing property damage, bodily injury,

or death. See the ENCLOSURE / VENTILATION REQUIREMENTS section for details.

The unit serial number is located inside the control panel and on the underside of the drip tray

handle. It is recommended that the drip tray ﬁrst be removed and cleaned / emptied of its contents,

then turned over to view. The unit rating label is located on the inside of the control panel.

INSTALLATION, OPERATION, AND SAFETY INFORMATION

5

WARNING

This gas appliance, its enclosure, and the propane cylinder enclosure, if any, MUST be plumbed and vented

in accordance with local building and safety codes and should be approved by local code enforcement

ofﬁcials. This appliance MUST be installed and operated according to the information below.

FAILURE TO PROPERLY VENT THE ENCLOSURE MAY RESULT IN A FIRE OR EXPLOSION CAUSING

PROPERTY DAMAGE, BODILY INJURY, OR DEATH.

A leaking gas connection or valve unintentionally left open will create a hazard.

WHEN USING PROPANE GAS

• Propane gas (also known as L.P. gas) is heavier than air and will accumulate or pool in an inadequately

vented enclosure or recessed area.

• If a pool of propane gas is ignited, an explosion will occur. Adequate venting at the ﬂoor level, or the lowest

point where gas could accumulate, will eliminate this danger.

Refer to the ENCLOSURE / VENTILATION REQUIREMENTS section.

Observe all local codes.

• DO NOT store a spare propane-gas cylinder under or near the enclosure.

WHEN USING NATURAL GAS

• Natural gas is lighter than air and will accumulate at the top of an inadequately vented enclosure.

• If an accumulation of natural gas is ignited, an explosion will occur. Adequate venting at the top of the

enclosure, or the highest point where gas could accumulate, will eliminate this danger.

Refer to the ENCLOSURE / VENTILATION REQUIREMENTS section.

Observe all local codes.

INSTALLATION SAFETY GUIDELINES

THIS UNIT MUST BE INSTALLED SO THAT THE REQUIRED VENT OPENINGS AND SURROUNDING AREA

OF THE ENCLOSURE REMAIN CLEAR AND FREE AT ALL TIMES. See the ENCLOSURE / VENTILATION

REQUIREMENTS section for details.

CAUTION: FOR YOUR SAFETY, you must provide openings in the enclosure for replacement air and

ventilation (in case of possible leakage from gas connections or propane cylinders). Failure

to do so may result in a ﬁre or explosion causing property damage, bodily injury, or death.

See the ENCLOSURE / VENTILATION REQUIREMENTS section for details.

The gas cylinder, regulator, and rubber hose must be in a location not subject to temperatures above

125° F (51° C).

IF A PROPANE CYLINDER IS INSTALLED INSIDE OF THE ENCLOSURE, THE GUIDELINES FOUND IN THE

ENCLOSURE / VENTILATION REQUIREMENTS SECTION MUST BE FOLLOWED.

WHEN OPERATING THIS GAS APPLIANCE, ALL INSTRUCTIONS AND WARNINGS

MUST BE OBSERVED. FAILURE TO DO SO MAY RESULT IN A FIRE OR EXPLOSION

CAUSING PROPERTY DAMAGE, BODILY INJURY, OR DEATH.

Every time you use the unit, make sure that:

1. The area around the enclosure is clear and free from combustible materials, gasoline and ﬂammable vapors/

liquids.

2. There is no blockage of the airﬂow through the vent openings located on the enclosure.

3. The hose is inspected (if applicable). See SAFE USE & MAINTENANCE OF PROPANE-GAS CYLINDERS section.

DO NOT store any combustible materials, gasoline, and any other ﬂammable vapors/liquids in the vicinity of the

unit. Provide adequate clearance for servicing and operation.

GAS SAFETY INFORMATION

OPERATING THE UNIT SAFELY AND CORRECTLY

6

U

L

Fig. 6-1 type coupleur de ﬁl de point culminant d’I

Valve

de

décompression

QCC

Type 1

Valve

Ajustage de précision

en laiton de ﬁl de

point culminant

Indicateur

de niveau

de liquide

(facultatif)

Écrou de main avec le

ﬁl de point culminant.

Régulateur

Passage

Tuyau

Volant de commande

main dans le sens des aiguilles d’une montre pour engager les

ﬁls et pour serrer jusqu’à ce que douillettement. L’utilisation des

pinces ou de la clé ne devrait pas être nécessaire. Seulement

le propane marqué par cylindres doit être employé.

Pour débrancher: Tournez l’écrou de main dans le sens

contraire des aiguilles d’une montre jusqu’à isolé (ﬁg. 6-1).

Important: Avant d’employer le unité, et ensuite chaque

fois que le cylindre est enlevé et rattaché,

examinez tous les raccordements pour

déceler les fuites. Arrêtez les valves de unité

et ouvrez la valve principale de cylindre, puis

vériﬁez les raccordements avec de l’eau

savonneux. Réparez toutes les fuites avant

d’allumer le unité.

ATTENTION: Tournez toujours la valve principale de cylindre

de propane au loin après chaque utilisation,

et avant de déplacer le unité et le cylindre, ou

débrancher l’accouplement. Cette valve doit

rester fermée et le cylindre a débranché alors

que l’appareil n’est pas en service, quoique

l’écoulement de gaz soit arrêté par un dispositif

de sûreté quand le coupleur est débranché.

Inspectez soigneusement l’ensemble de tuyau chaque fois

avant que le gaz soit allumé. Un tuyau ﬁssuré ou efﬁloché doit

être immédiatement remplacé.

Si l'appareil est stocké à l'intérieur, le cylindre doit être disconnected

et a enlevé. Des cylindres Disconnected doivent être stockés

dehors, hors de la portée des enfants, avec les prises de valve

ﬁletées étroitement installées, et ne doivent pas être stockés dans

un bâtiment, le garage, ou n'importe quel autre secteur inclus.

POUR VOTRE SÛRETÉ

a. Ne stockez pas un cylindre de gaz disponible de propane

dessous ou ne vous approchez pas de cet appareil.

b. Ne remplissez jamais cylindre au delà de 80 pour cent de

plein.

c. SI L’INFORMATION DANS “A” ET “B” N’EST PAS SUIVIE

EXACTEMENT, UN FEU CAUSANT LA MORT OU DES

DOMMAGES SÉRIEUX PEUT SE PRODUIRE.

IMPORTANT POUR VOTRE SÛRETÉ

LISEZ ET SUIVEZ TOUS LES AVERTISSEMENTS ÉQUIPÉS DE VOTRE CYLINDRE DE GAZ DE PROPANE.

En actionnant cet appareil avec un cylindre de gaz de propane ON DOIT observer ces instructions et avertissements.

LE MANQUE DE FAIRE AINSI PEUT AVOIR COMME CONSÉQUENCE UNE INCENDIE OU UNE EXPLOSION SÉRIEUSE.

CYLINDRE ET CONDITIONS ET

CARACTÉRISTIQUES DE CONNECTEUR

a. Les bouteilles, les vannes et les tuyaux de propane doivent

être entretenus et inspectés avant chaque utilisation. Ils

doivent être remplacés en cas de dommages visibles. Si

le tuyau est coupé ou présente des signes d’abrasion ou

d’usure, il doit être remplacé avant utilisation (voir e.).

b. Cette unité, lorsqu'elle est utilisée avec une bouteille, doit

être connectée à une bouteille standard de gaz propane de

5 gallons (20 lb) équipée d'un dispositif anti-débordement

répertorié. L’appareil est obligatoire sur toutes les bouteilles

vendues depuis le 1er octobre 1998 aﬁn d’empêcher tout

remplissage excessif.

c. Les dimensions du cylindre doivent être d'environ 12 "(30,5 cm)

de diamètre et 18" (45,7 cm) de hauteur. Les bouteilles doivent

être construites et marquées conformément aux spéciﬁcations

du ministère des Transports (DOT) pour les bouteilles à gaz LP

ou à la norme relative aux bouteilles, sphères et tubes pour le

transport des marchandises dangereuses et à la Commission,

CAN / CSA-B339, selon le cas.

d. Le cylindre doit inclure un collier pour protéger la valve

de cylindre et le circuit d’alimentation de cylindre doit être

assuré le retrait de vapeur.

e. Le montage du régulateur de pression et le ﬂexible (Fig. 6-1)

fourni avec cet appareil au gaz en plein air (modèles au

propane seulement) doit être utilisé. Assemblées d'origine et

régulateur de pression et le tuyau de remplacement doivent

être ceux spéciﬁés par le fabricant pour le raccordement d'un

dispositif de cylindre de liaison identiﬁée comme de type I

par le ANSI Z 21.58/CGA 1.6 (voir liste des pièces pour les

informations de commande).

f. La valve de cylindre de gaz de propane doit être équipée

d’un dispositif d’accouplement de raccordement de

cylindre, décrit comme type I dans la norme déﬁnie dans le

e. de paragraphe ci-dessus. Ce dispositif est généralement

décrit comme coupleur de ﬁl de point culminant.

g. Si votre cylindre de gaz de propane vient avec une prise

de la poussière, placez le bouchon anti-poussière sur la

sortie de valve de cylindre toutes les fois que le cylindre

n’est pas en service.

OPÉRATION DE COUPLEUR

Pour relier le regulator/hose à l’ajustage de précision de

valve de cylindre de gaz de propane: Serrez l’écrou de main

sur le régulateur au-dessus de l’ajustage de précision de ﬁl

de point culminant sur la valve de cylindre. Tournez l’écrou de

1

2

3

4

e. Le régulateur de pression et l’ensemble de tuyau utilisé

doivent assortir les spéciﬁcations pour le type I par ANSI

Z 21.58/CGA 1.6 (voir la ﬁgue. 6-1).

Pour les besoins de ventilation et d'enceinte au propane,

Voir la section ENCLOSURE / VENTILATION REQUIREMENTS.

UTILISATION SÛRE ET ENTRETIEN DES CYLINDRES DE GAZ DE PROPANE

7

U

L

Fig. 7-1 Type I Acme thread coupler

Pressure

relief

valve

QCC

Type 1

valve

Brass Acme

thread ﬁtting

Liquid level

indicator

(optional)

Hand nut with Acme

thread

Regulator

Vent

Hose

Hand wheel

The use of pliers or a wrench should not be necessary. Only

cylinders marked “propane” may be used.

To disconnect: Turn the hand nut counterclockwise until

detached (Fig. 7-1).

Important: Before using the unit, and after each time

the cylinder is removed and reattached,

check the hose for wear (see a.) and check

all connections for leaks. Turn off the unit

valves and open the main cylinder valve,

then check connections with soapy water.

Repair any leaks before lighting the unit.

CAUTION: Always turn the propane cylinder main valve

off after each use, and before moving the unit

and cylinder or disconnecting the coupling.

This valve must remain closed and the

cylinder disconnected while the appliance

is not in use, even though the gas ﬂow is

stopped by a safety feature when the coupler

is disconnected.

Carefully inspect the hose assembly each time before the

gas is turned on. A cracked or frayed hose must be replaced

immediately.

If the appliance is stored indoors, the cylinder must be

disconnected and removed. Disconnected cylinders must be

stored outdoors, out of the reach of children, with threaded

valve plugs tightly installed, and must not be stored in a

building, garage, or any other enclosed area.

FOR YOUR SAFETY

a. DO NOT store a spare propane-gas cylinder under or

near this appliance.

b. NEVER ﬁll the cylinder beyond 80-percent full.

c. IF THE INFORMATION IN a. AND b. IS NOT FOLLOWED

EXACTLY, A FIRE CAUSING DEATH OR SERIOUS

INJURY MAY OCCUR.

IMPORTANT FOR YOUR SAFETY

READ AND FOLLOW ALL WARNINGS PROVIDED WITH THE PROPANE-GAS CYLINDER.

When operating this appliance with a propane-gas cylinder, these instructions and warnings MUST be observed.

FAILURE TO DO SO MAY RESULT IN A SERIOUS FIRE OR EXPLOSION.

CYLINDER/CONNECTOR REQUIREMENTS

a. Propane-gas cylinders, valves, and hoses must be

maintained in good condition and inspected before each use

of appliance. They must be replaced if there is any visible

damage. If hose is cut or shows excessive abrasion or wear,

it must be replaced before using appliance (see e.).

b. This unit, when used with a cylinder, should be connected

to a standard 5-gallon (20 lb.) propane-gas cylinder

equipped with a listed overﬁlling prevention device. The

device has been required on all cylinders sold since

October 1,1998, to prevent overﬁlling.

c. Cylinder dimensions should be approximately 12" (30.5

cm) in diameter and 18" (45.7 cm) high. Cylinders must

be constructed and marked in accordance with the U.S.

Department of Transportation (D.O.T.) Speciﬁcations for

LP-Gas Cylinders, or the Standard for Cylinders, Spheres,

and Tubes for Transportation of Dangerous Goods and

Commission, CAN/CSA-B339, as applicable.

d. The cylinder used must include a collar to protect the

cylinder valve, and the cylinder supply system must be

arranged for vapor withdrawal.

e. The pressure regulator and hose assembly (Fig. 7-1)

supplied with this outdoor gas appliance (L.P. models

only) must be used. Original and replacement pressure

regulator and hose assemblies must be those speciﬁed by

the manufacturer for connection with a cylinder connecting

device identiﬁed as Type I by the ANSI Z 21.58/CGA 1.6

(see PARTS LIST for ordering information).

f. The propane-gas cylinder valve must be equipped with

a cylinder connection device, described as Type I in the

standard deﬁned in paragraph e. above. This device is

commonly described as an Acme thread coupler.

g. If the propane-gas cylinder comes with a dust plug, place

the dust cap on the cylinder valve outlet whenever the

cylinder is not in use.

COUPLER OPERATION

To connect the regulator/hose assembly to the propane-

gas cylinder valve ﬁtting: Press the hand nut on the regulator

over the Acme thread ﬁtting on the cylinder valve. Turn the hand

nut clockwise to engage the threads and tighten until snug.

e. The pressure regulator and hose assembly used must

match the speciﬁcation for Type I by ANSI Z 21.58/CGA

1.6 (see Fig. 7-1).

For propane ventilation and enclosure requirements,

see the ENCLOSURE / VENTILATION REQUIREMENTS section.

SAFE USE & MAINTENANCE OF PROPANE GAS CYLINDERS

8

Fig. 8-1 Ventilation detail

Min.

90˚

Ventilation Requirements:

• Minimum 4 openings

(2 per side wall - spaced at min. 90 degrees)

• Top openings: within 5" of countertop (see below)

• Bottom openings: within 5" of ﬂoor (see below)

• Each vent opening: min. 10 sq. in. of free area

(Total = 40 sq. in. free area)

1"

max.

Keep surrounding

area and vent

openings clear and

free at all times.

5"

max.

1"

max.

5"

max.

Vent openings (4)

10 sq. in. of free

area min. (each)

(Total = 40 sq. in.)

Note: Vent openings example shown. Your design may vary.

• 6" min. clearance between all vent openings

and any items outside of enclosure

• 2" min. clearance between all vent openings

and any items within enclosure

Fig. 8-2 Vent openings clearance

2"

min.

(Side View)

6"

min.

Vent

opening

When installing this unit in a combustible

enclosure, an RHP insulating liner must be used.

Reference Table 1 for liner model #.

Fire Magic GFRC islands are available. They meet all

enclosure and ventilation requirements. For requirements

regarding custom-built enclosures, see below.

VENTILATION (ALL ENCLOSURES)

For All Piping Systems and All Gas Types:

(Natural Gas, Household Propane, L.P. Cylinder)

FOR YOUR SAFETY, you must provide the openings

listed below for replacement air and ventilation of

the enclosure (in case of possible leakage from gas

connections or L.P. cylinders). Failure to do so may

result in a ﬁre or explosion causing property damage,

bodily injury, or death.

One side of the enclosure shall be left completely open

to the outside; OR 4 (minimum) ventilation openings

MUST be created (reference Fig. 8-1 and Fig. 8-2):

• Each opening must have a minimum of 10 sq. in.

of free area. The openings must be equally sized.

(Total of 40 sq. in. free area.)

• Two openings must be in the side walls of the

enclosure, at the top level, and spaced at a minimum

of 90 degrees. The openings must begin 1" or less

below the countertop level and end no more than 5"

below the countertop level.

• Two openings must be in the side walls of the

enclosure, at the ﬂoor level, and spaced at a minimum

of 90 degrees. The openings must begin 1" or less

above the ﬂoor level and end no more than 5" above

the ﬂoor level.

• The openings must remain unobstructed:

The clearance between the openings and any items

outside of the enclosure is a minimum of 6". The

clearance between the openings and any items within

the enclosure is a minimum of 2". See Fig. 8-2.

When an L.P. cylinder is used in the enclosure, additional

requirements exist, see the following section.

It is acceptable to use RHP venting panels (PN 5510-01).

Contact your dealer.

KEEP THE REQUIRED VENT OPENINGS AND

SURROUNDING AREA OF THE ENCLOSURE CLEAR

AND FREE AT ALL TIMES.

WARNING: Ventilation openings in side walls shall not

communicate directly with other enclosures

of the outdoor cooking gas appliance.

ENCLOSURE / VENTILATION REQUIREMENTS

9

Fig. 9-3 Optional door w/ tank tray & louvers

Cylinder & regulator/hose assembly

protected by heatshield

Additional adapters may be required

for your setup (not included)

Equipped with

adapter for hose

assembly.

Flex connector

not included.

Fig. 9-2 Additional ventilation opening for L.P. cylinder

RHP DOOR MEETS ALL REQUIREMENTS ABOVE

Access

door

L.P.

cylinder

Ventilation

opening

(at cylinder gas

connection level,

min. 10 sq. in

free area)

(L.P. Cylinder setups only)

Louvers

Tray

ENCLOSURE

The countertop MUST be constructed of non-combustible

materials. The enclosure can be constructed of combustible

or non-combustible materials.

For combustible enclosures, an insulating liner is always

required (see Table 1).

WHEN A PROPANE (L.P.) CYLINDER IS USED IN

THE ENCLOSURE

When a propane (L.P.) cylinder is installed inside of the

enclosure, the additional guidelines below MUST be

followed. FAILURE TO DO SO MAY CAUSE DAMAGE

TO YOUR UNIT AND/OR PERSONAL INJURY. Refer to

Fig. 9-1 and 9-2.

• Only a C.S.A. listed stainless steel connector can be

connected to the unit.

• The regulator/hose assembly coming from the cylinder

can only be connected to the above mentioned ﬂex

connector. DO NOT connect the regulator/hose

assembly directly to the unit. An adapter will be

required.

• A non-combustible heatshield must be installed to

protect the regulator/hose assembly and cylinder valve.

• The cylinder must rest at least 2" above the ground.

• An additional vent opening is recommended in

the access door near the cylinder and at the gas

connection level (minimum 10 sq. in. of free area).

RHP offers an "access door with tank tray and louvers"

which includes a heatshield that rests directly above

the L.P. cylinder, a tray, and louvers to meet the cylinder

install requirements. The door is shown in Fig. 9-3.

Contact your dealer for ordering information.

Adapter

Power burner

C.S.A.

listed

stainless

steel ﬂex

connector

Non-combustible

Heatshield

Regulator/

hose

assembly

L.P.

cylinder

2" min. from

ground

Fig. 9-1 L.P cylinder orientation

ENCLOSURE / VENTILATION REQUIREMENTS (cont.)

10

Installation must be performed by a qualiﬁed professional

service technician.

This unit is designed for outdoor use only. DO NOT use this

unit inside a building, garage, or enclosed area. DO NOT use

this unit in or on a recreational vehicle or boat.

OVERHEAD CONSTRUCTION AND EXHAUST

HOOD REQUIREMENTS

A minimum 5 foot clearance is required between the countertop

and the overhead construction.

When installed under combustible overhead construction,

the area above the cooking surface of the unit must be

covered with an exhaust hood. The exhaust hood provides

the protection for the combustible overhead construction.

See exhaust hood information below and Fig. 10-1.

Important: DO NOT use this appliance under unprotected

combustible overhead construction.

When installed under overhead non-combustible construction,

an exhaust hood is highly recommended; see exhaust hood

information below and Fig. 10-1.

Exhaust Hood

When using an exhaust hood, the area above the cooking

surface of the power burner must be covered with a hood

larger than the cooking area of the power burner, and with a

minimum of 1200 CFM (cubic feet per minute) rated exhaust

fan for proper outdoor application.

INSTALLATION REQUIREMENTS

Fig. 10-1 Overhead requirements

Min.

5'

OVERHEAD CONSTRUCTION

EXHAUST

HOOD

Combustible overhead

construction:

Exhaust hood required

Non-combustible

overhead construction:

Exhaust hood highly recommended

N

O

N

C

O

M

B

U

S

T

I

B

L

E

W

A

L

11

REAR WALL CLEARANCES

For the minimum clearances between the unit and rear walls,

your setup must fall within one (or more) of the following:

A. Clearance between unit and strictly non-combustible

rear wall

(i.e. brick wall, see Fig. 11-1)

• The unit must have a minimum clearance of 4" from

the non-combustible rear wall.

(To allow for proper ventilation and prevent dangerous

overheating.)

B. Clearance between unit and a protected combustible

rear wall

(i.e. a non-combustible wall in front of a combustible wall

to serve as a barrier. This can be accomplished by brick,

or a metal stud ﬁnished with non-combustible substrate,

see Fig. 11-2)

• The unit must have a minimum clearance of 14" from

the protected combustible rear wall.

(The 4" non-combustible material plus an additional 10"

clearance between the unit and protected rear wall.)

C. Clearance between unit and combustible rear wall

• The unit must have a minimum clearance of 18" from

the combustible rear wall (see Fig. 11-3).

BACKSPLASH CLEARANCE (if applicable)

If a non-combustible backsplash exists, it must have a minimum

of a 4" clearance from the rear of the unit (to allow for proper

ventilation and prevent dangerous overheating). See Fig. 11-4.

Important: This 4" backsplash clearance must ﬁrst be met

prior to any non-combustible walls beginning

behind it.

SIDE WALL / CORNER WALL CLEARANCES

(if applicable)

The unit must have a minimum clearance of 18" from any

side walls (to account for variables in airﬂow that could affect

performance). See Fig. 11-5.

INSTALLATION REQUIREMENTS (Cont.)

Min.

18"

Fig. 11-3 Clearance 'C' Diagram

Combustible

(Clearance required for

rear wall)

Min.

14"

Fig. 11-2 Clearance 'B' Diagram

Non-combustible

substrate

Non-combustible 4"

Com-

bustible

(Clearance required for

rear wall)

Min.

4"

Fig. 11-1 Clearance 'A' Diagram

Non-combustible

(Clearance required for

rear wall)

Fig. 11-4 Backsplash clearance

Non-combustible

Backsplash

Min.

4"

Fig. 11-5 Side/corner wall clearance

Min.

18"

Clearances continued on following page

12

CONTROL PANEL CLEARANCES

• The control panel MUST have a minimum side

clearance of 6" from any obstructions/side walls. See

Fig. 12-1.

(To allow for access to light switch and control panel

removal.)

• The control panel MUST remain removable for

servicing (see CONTROL PANEL REMOVAL section).

Any adjacent countertops must not obstruct the panel

from being removed.

COMBUSTION AIR AND COOLING AIRFLOW

Proper airﬂow (front-to-back, Fig. 12-2) MUST be maintained

for the unit to perform as it was designed. If airﬂow is blocked,

overheating and poor combustion will result. Do not block the

1" front air inlet along the bottom of the control panel.

GAS-SUPPLY PLUMBING REQUIREMENTS

For natural gas or a household propane system, rigid

1

/

2

" or

3

/

4

" black steel pipe or local code-approved pipe is required

to conduct the gas supply to the unit. Contact your local gas

supplier. Connect this pipe to the required C.S.A.-approved

stainless-steel ﬂex connector (attached). An NPT adapter

has been provided for

1

/

2

" pipe. DO NOT use a rubber hose

within the unit enclosure. Apply only joint compounds that

are resistant to all gasses on all NPT pipe ﬁttings except ﬂare

ﬁttings. Make sure to tighten all ﬁttings securely.

Note: If

1

/

2

" pipe is used with natural gas, it should be

no longer than 20'.

Important: A shut-off valve (not included) in the gas

line is required. It provides for safety when

the unit is not in use and for convenient

maintenance and repair. It must be installed

within 6 feet of the unit. If it is located within

the enclosure, it must be easily accessible.

Use a pipe joint compound resistant to

all gasses on all male ﬁttings except ﬂare

ﬁttings.

GAS SUPPLY AND MANIFOLD PRESSURES:

For natural gas - normal 7" water column (w.c.), minimum

5", maximum 10

1

/

2

". For propane gas - normal 11" w.c.,

minimum 10", maximum 13".

INSTALLATION REQUIREMENTS (Cont.)

Fig. 12-2 Airﬂow diagram

(1" front air inlet)

Fig. 12-1 Control panel clearances

Min.

6"

Min.

6"

13

• To protect against electric shock, do not immerse cord or plugs in water or other liquid.

• Unplug from the outlet when not in use and before cleaning. Allow to cool before putting on or taking off parts.

• Do not operate any outdoor cooking gas appliance with a damaged cord, plug, or after the appliance

malfunctions or has been damaged in any manner. Contact the manufacturer for repair.

• Do not let the cord hang over the edge of a table or touch hot surfaces.

• Do not use an outdoor cooking gas appliance for purposes other than intended.

• When connecting, ﬁrst connect plug to the outdoor cooking gas appliance then plug appliance into the outlet.

• Use only a properly wired and inspected 120VAC (15 AMP minimum) Ground Fault Circuit Interrupter

(GFCI) GROUNDED 3-wire receptacle with this outdoor cooking gas appliance.

• The GFCI receptacle must be a WEATHER-PROOF IN-USE COVERED RECEPTACLE.

• Never remove the grounding plug or use with an adapter of 2 prongs.

• Use only extension cords with a 3 prong grounding plug, rated for the power of the equipment, and approved

for outdoor use with a W-A marking.

• The provisions of the National Electric Code as well as any local codes must be observed when

installing the product.

ELECTRICAL SAFETY

14

MODEL SPECIFICATIONS

Height Width Depth

(Top to bottom) (Left to right) (Front to back)

Top of hanger to

bottom of unit

(A)

Hanger to hanger

(B)

Control panel

width

(C)

Maximum depth

(D)

12" 20

3

/4" 19

3

/4" 23

3

/4"

D

A

B

Fig. 14-1

C

Table 2 - Dimensions

19-7B Series

Inner burner

N/P (right) oriﬁce drill size

#46 / #1.25

Outer burner

N/P (left) oriﬁce drill size

#30 / #50

Fire Magic insulating liner model # (not included)* 3278-52

Input electrical requirements 100~240 VAC / 1.90A max. / 50/60 Hz / GFCI outlet

Electrical output 13 VDC / 150 Watts

*Note: If installing this unit in a combustible enclosure, the correct insulating liner must be used. Consult liner instructions

for counter cutout dimensions and installation.

Table 1 - Product Speciﬁcations

15

COUNTERTOP OVERHANG

The control panel is designed to sit ﬂush against the enclosure front wall. If the enclosure countertop extends

beyond the front wall, creating a countertop overhang, it must be cut ﬂush with the front wall for the width of the

control panel or a gap will be created exposing the forward portions of the left and right side ﬁre walls of the

unit. See illustrations above.

ENCLOSURE VENTILATION

FOR YOUR SAFETY, you must provide openings in the enclosure for replacement air and ventilation (in case of

possible leakage from gas connections or propane cylinders). Failure to do so may result in a ﬁre or explosion

causing property damage, bodily injury, or death. See the ENCLOSURE / VENTILATION REQUIREMENTS

section for details.

X= D-B

÷

2

Y= Total

Countertop

Overhang

Note: It is highly recommended to build the enclosure with an offset counter height for

the power burner installation. See the RECOMMENDED OFFSET INSTALL section

on the following page for details.

TOP VIEW

Countertop

overhang

Control panel

NON-COMBUSTIBLE

ENCLOSURE CUTOUT

DIMENSIONS

Fig. 15-1

FRONT VIEW

B

C

D

See next page

for substrate

considerations

Countertop

overhang

X

TOP VIEW

SIDE VIEW

Countertop

overhang

(Control

panel)

(Countertop)

Y

1

/

4

"

Clearance

(Overhang)

A

Control

panel

Check clearance for

control panel removal

MODEL SPECIFICATIONS (cont.)

19-7B Series

A Countertop to unit bottom cutout* 11

1

/

2

"

B Side to side non-combustible cutout* 19"

C Front to back non-combustible cutout*† 18

3

/

4

"

D Control panel width non-combustible cutout‡ 20

1

/

4

"

*Note: If installing this unit in a combustible enclosure, the correct insulating liner must be used. Consult liner

instructions for counter cutout dimensions and installation.

†

Includes any substrate at front wall of enclosure (in the area the rear of the control panel is to sit ﬂush against).

See SUBSTRATE section on next page.

‡

Only applicable for non-combustible enclosures that have countertops with an overhang (see illustration and section

below).

Table 3 - Cutout Dimensions

Lower

support

2

3

/4"

4"

1

/2" ø or 1

1

/2"

square hole

for electrical

supply

2

3

/4"

4"

1

/2" ø or

1

/2" square

hole for gas

supply

16

SUBSTRATE

When adding any substrate to the enclosure front wall (including tiles, stone, etc.), consider the following:

Substrate Behind Control Panel

Substrate Alongside Control Panel

C

Flush

(Control panel)

(Countertop)

(Control panel)

Substrate

(includes tiles,

etc. at front of

enclosure)

Countertop

overhang

(if applicable)

Flush

Power burner

liner

Substrate

(includes tiles,

etc. at front of

enclosure)

1

/4"

Clearance

Any additional substrate alongside the control panel

does not need to be considered in Dim. C (see previous

page), however a

1

/4" clearance on each side (same as

overhang) and below is required.

Substrate

+

countertop "front to back" cutout

must equate to Dim. C (see previous page)

when the substrate sits ﬂush behind the

control panel.

Fig. 16-2 Fig. 16-3

Countertop

overhang

(if applicable)

TOP VIEW TOP VIEW

1

/4"

Clearance

RECOMMENDED OFFSET INSTALL

It is highly recommended to build the enclosure for the power burner 6"-12" LOWER than your countertop (see Fig. 16-1).

This will ensure a safer environment when using tall cooking pots like a turkey fryer, which can hold 40 lbs of hot oil.

Consult Table 3 for power burner cutout dimensions. See Fig. 16-1 below for countertop offset installation information.

Important: The surrounding non-combustible walls must have a minimum clearance of 2" beyond

the power burner hangers to allow for proper installation, airﬂow, and ventilation.

If using an insulating liner:

• Consult liner instructions for

enclosure cutout dimensions

and installation.

• Ensure the 2" clearance for the

surrounding non-combustible

walls is calculated beyond the

insulating liner hangers.

Power burner

liner

2" min.

6-12"

Fig. 16-1

MODEL SPECIFICATIONS (cont.)

17

Note: In addition, a wire diagram for this unit can be

found afﬁxed to the inside of the control panel.

Burner igniter

Wire harness

extension

Wire harness

assembly

Burner

manifold

Ground wire

WIRING DIAGRAM

Lighted bezels

Light switch

MODEL SPECIFICATIONS (cont.)

18

Replacement parts can be ordered

from your local Fire Magic Grill

dealer.

PARTS LIST

3

11

15

10

19-7B Series

Item Description Part No. Qty.

1.

Power burner lid 3278-06 1

2.

Porcelain cast iron cooking grid 3545 1

or

Stainless steel cooking grid 3545-S 1

3.

Interior protection plate 3278-30 1

4.

Flame collimator (stir fry ring) 3278-09 1

5.

Burner assembly 3278-01B 1

6.

Air shutter spring (set of 2) 3048-03-2 1

7.

Natural gas oriﬁce (left)

‡

3001-30-1 1

or

Propane gas oriﬁce (left)

‡

3001-50-1 1

8.

Natural gas oriﬁce (right)

‡

3001-46-1 1

or

Propane gas oriﬁce (right)

‡

3001-1.25-1 1

9.

Igniter assembly 4199-52 1

10.

Valve manifold 3278-14 1

11.

Small knob (inner burner) 24182-42 1

12.

Large knob (outer burner) 24182-41 1

13.

Lighted bezel assembly (small) 24182-64 1

14.

Lighted bezel assembly (large) 24182-63 1

15.

Control panel 23278-32 1

16.

Drip tray w/ match holder 3085 1

17.

Wire harness assembly

‡

23278-25 1

18.

Wire harness extension

‡

24182-55 1

19.

Convertible regulator PR-4 1

20.

Flex connector w/ ﬁttings

‡

3031 1

21.

Power supply w/ cord *

‡

24182-18 1

22.

Light switch 24182-48 1

* Optional / purchased separately

‡

Not shown

16

2

4

5

12

19

9

6

14

13

22

1

19

Fig. 19-3 Connecting to a gas line

Gas supply

(NPT)

Flex

connector

(from unit)

Flare-to-NPT

Shut-off valve*

(end of

gas supply)

NPT-to-NPT

Shut-off valve*

(in-line)

Gas supply

(NPT)

Flare-to-NPT

adapter

Flex

connector

(from unit)

* Shut-off valve: required, not included, must

be within 6 feet of unit

A B

-OR-

It is not required to remove the control panel or knobs to

install this unit.

DO NOT lift the unit from the control panel when installing.

COUNTER PREPARATION

Consult Table 1 for non-combustible enclosure cut-out

dimensions. A RHP insulating liner must be used if any

supporting construction is combustible. Consult the instructions

that come with the liner for dimensions and additional installation

information before beginning the installation.

This power burner must be supported by the stainless-steel

hanger extending from the upper portion of the frame. The

hanger rests on the left, right, and back of the countertop.

The control panel is designed to sit ﬂush against the enclosure

front wall (see Fig. 19-1). If the non-combustible enclosure

countertop extends beyond the front wall, creating a countertop

overhang (see Fig. 19-2), it must be cut ﬂush with the front

wall for the width of the control panel or a gap will be created

exposing the forward portions of the left and right side ﬁre walls

of the unit. See the MODEL SPECIFICATIONS section.

CONNECT THE GAS SUPPLY

For propane cylinders:

For connecting a propane unit to a portable propane tank,

read the safety warnings and follow the instructions in the

section SAFE USE AND MAINTENANCE OF PROPANE GAS

CYLINDERS.

Note: When a propane cylinder is installed inside of the

enclosure, the guidelines found in the ENCLOSURE

/ VENTILATION REQUIREMENTS section MUST be

followed.

For household propane or natural gas units:

CAUTION: Use only C.S.A. listed stainless-steel flex

connectors within the enclosure.

WARNING

A rubber or plastic connector will rupture or leak, resulting

in an explosion or serious injury if used inside the appliance

enclosure.

1. Locate the attached ﬂex connector (found underneath the

unit) and route it to the gas-supply stub.

2. Turn OFF the gas supply at the source.

3. A shut-off valve is required within 6 feet of the unit.

If shut-off valve is installed in-line:

• Install the supplied ﬂare-to-NPT adapter to the gas

supply (NPT) using a pipe joint compound resistant to

all gasses (see Fig. 19-3, A). Tighten securely.

• Connect the ﬂex connector to the adapter (see Fig. 19-3,

A). Tighten securely.

If shut-off valve is connected to end of gas supply stub:

• Connect the ﬂex connector to the shut-off valve (ﬂare)

(see Fig. 19-3, B). Tighten securely.

INSTALLATION

(Countertop)

GAP CREATED

Proposed cut-out

in overhang

Control panel

stops here

INCORRECT

Fig. 19-2 Countertop overhang - incorrect cutout

Fig. 19-4 Household propane & nat. gas diagram

OFF

To gas

system

Gas supply (NPT)

Flex

connector

Hanger

Countertop

Cut-out

Flare -to-NPT

adapter

Shut-off valve

(shown in-line) must

be within 6 feet of

the unit.

IDEAL

Flush-mounted

control panel

Overhang

Fig. 19-1 Countertop overhang - correct cutout

CORRECT

(Countertop)

20

4. Turn burner control knob(s) to the OFF position. Turn the gas supply on. Then carefully check all gas connections

for leaks with a brush and half-soap/half-water solution before lighting. NEVER USE A MATCH OR OPEN

FLAME TO TEST FOR LEAKS.

5. Close the shut-off valve.

POWER SUPPLY & WIRE HARNESS CONNECTIONS

CAUTION: IMPROPERLY CONNECTED WIRES WILL CAUSE DAMAGE TO THE UNIT AND MAY RESULT IN

PROPERTY DAMAGE AND/OR PERSONAL INJURY.

The unit comes with a 6' wire extension to retrieve power from a separately purchased Aurora grill. Aurora grills are

equipped with power supply boxes, which can supply power to the power burner (see AURORA GRILL POWER

SUPPLY BOX section below).

Alternatively; an optional power supply box may be ordered and installed to independently power this unit (see

following INDEPENDENT POWER SUPPLY section). Contact your dealer for ordering information.

Important: If installing with an Echelon Griddle, the power burner must be powered with an independent power

supply. A griddle power supply cannot be used with Echelon side cookers.

TO INSTALL USING AN AURORA GRILL POWER SUPPLY BOX:

1. Locate the power supply box that is connected to the Aurora Grill and ensure the power cord is disconnected,

if connected (see Fig. 20-1, A).

2. Disconnect the grill wire harness extension connectors from the power supply connectors (see Fig. 20-1, B).

INSTALLATION (cont.)

Continue to next pages for section appropriate to your setup (3A, 3B, or 3C).

Grill wire harness

(comes attached to grill)

Power supply

DO NOT

DISCONNECT

B

A

Disconnect

POWER

SUPPLY

POWER

SUPPLY

Fig. 20-1

Follow the text/illustrations below and on one of the following pages for proper wire

connections. The wire harnesses are labeled to further assist with connections.

La page est en cours de chargement...

FireMagic Aurora Power Burner Manuel utilisateur

FireMagic Aurora Power Burner Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents