Fire Magic Echelon Diamond Portable Griddle Manuel utilisateur

1

IMPORTANT: READ THESE INSTRUCTIONS CAREFULLY BEFORE STARTING INSTALLATION OR USE.

PORTABLE OUTDOOR GAS GRIDDLE

Robert H. Peterson Co. • 14724 East Proctor Avenue • City of Industry, CA 91746

INSTALLATION AND

OWNER’S MANUAL

INSTALLER: Leave these instructions with consumer.

CONSUMER: Retain for future reference.

WARNINGS AND SAFETY CODES

DANGER:

IF YOU SMELL GAS:

1. Shut off the gas to the appliance.

2. Extinguish any open ﬂame.

3. Open lid.

4. If odor continues, keep away from the

appliance and immediately call your

gas supplier or the ﬁre department.

WARNING:

1. Do not store or use gasoline or other

ﬂammable vapors and liquids in the

vicinity of this or any other appliance.

2. An LP cylinder not connected for use

shall not be stored in the vicinity of this

or any other appliance.

CODE AND SUPPLY REQUIREMENTS: This griddle

must be installed in accordance with local codes and

ordinances, or, in the absence of local codes, with the

latest National Fuel Gas Code (ANSI Z223.1/NFPA

54), or Natural Gas and Propane Storage and Handling

Installation Code (CSA-B149.1).

This appliance and its dedicated manual shutoff valve

must be disconnected from the gas-supply piping

system when testing the syst

em at pressures in

excess of ½ psig (3.5 kPa).

This appliance must be isolated from the gas-

supply piping system by closing its dedicated

manual shutoff valve during any pressure testing

of the gas-supply system at pressures up to and

including ½ psig (3.5 kPa).

All electrical outlets in the vicinity of the griddle

must be properly grounded in accordance with

local codes, or, in the absence of local codes, with

the National Electrical Code, ANSI/NFPA 70, or the

Canadian Electrical Code, CSA C22.1, whichever

is applicable.

Keep all electrical-supply cords and fuel-supply

hoses away from any heated surface.

Robert H. Peterson Co. • 14724 East Proctor Avenue • City of Industry, CA 91746

WARNING:

Improper installation, adjustment, alteration,

service, or maintenance can cause injury or

property damage. For proper installation,

refer to the installation instructions. For

assistance or additional information, consult

a qualiﬁed professional service technician,

service agency, or the gas supplier.

Certiﬁed to: ANSI Z21.58

CSA 1.6

Proper operation of your griddle

requires prompt and periodic

maintenance. See the SERVICING

AND CLEANING section for details.

US

®

C

GETTING STARTED

REV 1 - A - 1912021100

L-C2-589

ECHELON

diamond series

E660s-0T4(N,P)

2

IMPORTANT: LISEZ CES INSTRUCTIONS SOIGNEUSEMENT AVANT DE COMMENCER L’INSTALLATION OU L’UTILISATION

PLATINE GAZ EXTÉRIEURE AU GAZ D’ÉCHELON

DANGER:

SI VOUS SENTEZ LE GAZ :

1. Coupez le gaz à l’appareil.

2. Éteignez-vous n’importe quelle ﬂamme nue.

3. Ouvrez le couvercle si équipé d’un four.

4. Si l’odeur continue, gardez loin de

l’appareil et appelez immédiatement

votre département de fournisseur ou de

feu de gaz.

AVERTISSEMENT:

1. Ne stockez pas ou n’employez pas

l’essence ou d’autres vapeurs et liquides

inﬂammables à proximité de ceci ou

d’aucun autre appareil.

2. Un cylindre de propane non relié pour

l’usage ne sera pas stocké à proximité

de ceci ou d’aucun autre appareil.

CONDITIONS DE CODE ET D’APPROVISIONNEMENT:

Ce gril doit être installé selon des codes et des ordonnances

locaux, ou, en l’absence des codes locaux, avec l’un ou l’autre

le plus défunt Code national de gaz de carburant (norme ANSI

Z223.1/NFPA 54), et Stockage de gaz naturel et de propane

et manipulation du code d’installation (CSA-B149.1).

Cet appareil et ses différents robinets d’isolement doivent être

démontés du gaz-fournissent le système sifﬂant en examinant

le système aux pressions au-dessus du ½ psig (kPa 3.5).

Cet appareil doit être isolé dans gaz-fournissent le système

sifﬂant par fermeture que ses différents robinets d’isolement

manuels pendant tous les essais sous pression du gaz-

fournissent le système aux pressions jusques et y compris

le ½ psig (kPa 3.5).

Toutes les sorties électriques à proximité du gril doivent être

correctement fondues selon des codes locaux, ou en l’absence

de local code, avec le code électrique national, ANSI/NFPA

70, ou le code électrique canadien, CSA C22.1, celui qui est

applicable.

Maintenez tout électrique-fournissent des cordes et carburant-

fournissent des tuyaux partis de n’importe quelle surface de

chauffage.

INSTALLATEUR : Laissez ces instructions avec le consommateur.

CONSOMMATEUR : Maintenez pour la future référence.

AVERTISSEMENT:

L’installation inexacte, l’ajustement, le

changement, le service, ou l’entretien peuvent

causer des dommages ou des dégats matériels.

Référez-vous à ce manuel. Pour de l'aide

ou des renseignements supplémentaires,

consultez un technicien professionnel qualiﬁé

de service, une agence de service ou le

fournisseur de gaz.

SÛRETÉ ET CODES D’AVERTISSEMENT

• Ce gril est pour ultilisation à l’extérieur seulement.

Si l’appareil est entreposé à l’intérieur, enlever les

bouteilles et les laisser à l’extérieur.

• Ne pas ranger le gril immédiatement aprés l’avoir utilisé.

le laisser refroidir avant de le déplacer ou de la ranger.

Le non respect de cette mesure de sécurité pourrait

entraîner un incendie causant des dommages à la

propriété, des blessures ou la mort.

• Ne pas utiliser cet appareil sous une surface combustible.

• Ne pas utiliser cet appareil sous un auvent. Le non

respect de cette mesure de sécurité pourrait entraîner

un incendie ou des blessures.

• Dégagement minimal entre les parois latérales et l’arriére

de l’appareil et la construction combustible (45.7 cm à

partir des parois latérales et 45.7cm à partir de l’arriére).

• Le régulareur de pression de gaz prévu avec cet appareil

de cuisson à gaz pour l’extérieur doit être utilisé. Ce

régulateur est réglé pour une pression de sortie de 5

pouces de colonne de l’eau pour le gaz naturel, et 10

pouces pour le propane.

• LE RÉGULATEUR INCLUS D’APPAREILS EST ÉVALUÉ

POUR LE MAXIMUM DE 1/2 (LIVRES PAR POUCE

CARRÉ). SI VOTRE OFFRE DE GAZ EST 1/2 PLUS

GRAND QUE (LIVRES PAR POUCE CARRÉ), UN

RÉGULATEUR ADDITIONNEL DOIT ÊTRE INSTALLÉ

AVANT LE GRIL. VOIR LA SECTION DE CONDITIONS

D’OFFRE DE GAZ POUR LA PRESSION APPROPRIÉE

D’OFFRE DE GAZ.

• Ne couvrez jamais la surface entière de cuisine ou de

gril de gauffreuses ou de casseroles. La surchauffe se

produira et les brûleurs ne seront pas très performants

quand la chaleur de combustion est emprisonnée au-

dessous de la surface à cuire.

• Ne pulvérisez jamais l’eau sur une unité chaude de gaz,

comme ceci peut endommager des composants de

porcelaine ou de fer de fonte.

• Une fuite de GPL peut causer une incendie ou une

explosion si enflammée entraînant des blessures

corporelles graves ou la mort.

• Communiquez avec le fournisseur de GPL pour les

réparations ou pour disposer de qules bouteille ou du

GPL non utilisé.

INSTALLATION INSTRUCTIONS ET MANUEL DU PROPRIÉTAIRE

Certiﬁé à la norme ANSI : Z21.58 / CSA 1.6

REV 1 - A - 1912021100

L-C2-589

3

CONTENTS

GETTING STARTED

INSTALLATION, OPERATION, AND

SAFETY INFORMATION �� 4

ELECTRICAL CONNECTIONS �� 4

GAS SAFETY INFORMATION �� 5

WARNING �� 5

WHEN USING PROPANE GAS �� 5

WHEN USING NATURAL GAS �� 5

INSTALLATION SAFETY GUIDELINES�� 5

OPERATING THE UNIT SAFELY AND CORRECTLY � 5

SAFE USE & MAINTENANCE OF PROPANE

GAS CYLINDERS �� 7

INSTALLATION REQUIREMENTS �� 8

OVERHEAD CONSTRUCTION AND EXHAUST

HOOD REQUIREMENTS

�� 8

REAR WALL CLEARANCES �� 9

SIDE WALL / CORNER WALL CLEARANCES

(if applicable)

�� 9

COMBUSTION AIR AND COOLING AIRFLOW �� 10

GAS-SUPPLY PLUMBING REQUIREMENTS �� 10

ELECTRICAL SAFETY �� 11

MODEL SPECIFICATIONS �� 12

PORTABLE GRIDDLE WIRING DIAGRAM �� 13

GRIDDLE REPLACEMENT PARTS LIST �� 14

INSTALLATION

INSTALLATION �� 16

LOCATION PREPARATION �� 16

WHEELS AND CASTERS �� 16

REMOVE PACKAGED CONTENTS AND

GRIDDLE TOP

�� 16

CONNECT THE GAS SUPPLY �� 17

LIGHTING TEST �� 17

REPLACE GRIDDLE TOP ASSEMBLY �� 17

INSTALL REAR EXHAUST PLATE �� 18

INSTALL THE DRIP COLLECTOR TROUGH �� 18

INSTALL THE DRIP TRAY �� 18

USE, CARE, & SERVICE

IDENTIFICATION OF GRIDDLE CONTROLS �� 19

USING THE GRIDDLE �� 20

LIGHTING (IGNITION) INSTRUCTIONS �� 21

ELECTRONIC LIGHTING �� 21

MANUAL LIGHTING �� 21

SHUTTING OFF THE UNIT �� 21

USING THE FOLDING SHELF �� 23

PAPER TOWEL HOLDER �� 23

REMOVING DRAWERS �� 23

SERVICING AND CLEANING �� 24

CLEANING YOUR GRIDDLE �� 24

GRIDDLE TOP REMOVAL �� 26

HEAT DISTRIBUTION GRID(S) REMOVAL �� 26

BURNER(S) REMOVAL �� 27

DRIP TRAY CHUTE REMOVAL �� 27

CONVERT GAS TYPE / CHECK BURNER ORIFICES �� 28

AIR SHUTTER ADJUSTMENT �� 30

POWER SUPPLY FUSE REPLACEMENT �� 31

CONTROL PANEL REMOVAL �� 32

TROUBLESHOOTING �� 33

WARRANTY �� 34

REV 1 - A - 1912021100

L-C2-589

4

1. The outdoor appliance and surrounding area MUST

remain clear of ﬂammable substances such as gasoline,

yard debris, wood, etc. Maintain a minimum horizontal

clearance of 18" (in all directions) from combustible

materials/items.

2. Do not block the 1" front air inlet along the bottom of

the control panel. See the COMBUSTION AIR AND

COOLING AIRFLOW section under INSTALLATION

REQUIREMENTS for details.

3. This unit must be installed so that the vent

openings on the cabinet remain clear and free at

all times. See the GAS SAFETY INFORMATION

section.

4. When using propane gas: the propane cylinder,

regulator, and rubber hose must be in a location

not subject to temperatures above 125° F (51° C).

5. The griddle lid must be removed before using unit.

6. The ﬂames on each burner burn evenly along the

entire burner with a steady ﬂame (mostly blue). The

unit has burner ﬂame viewing cutouts to observe the

burner ﬂames (see IDENTIFICATION OF GRIDDLE

CONTROLS section). If burner ﬂames are not normal,

check and clean the oriﬁce and burner/venturi tubes

for insects and insect nests. A clogged tube can lead

to a ﬁre beneath the unit. A proper ﬂame pattern will

ensure safe operation and optimal performance.

Adjust the air shutter as needed (see AIR SHUTTER

ADJUSTMENT section).

7. The in-line gas valve or gas cylinder valve must always

be shut OFF when the unit is not in use.

8. The drip collector trough holes must be clear and

unobstructed. Excessive grease deposits can result

in a grease ﬁre.

9. Whenever reconnecting any wires, apply a small

amount of dielectric grease to the male connector,

then make the connection. This will ensure conductivity

and prevent moisture from affecting the contact.

10. Wear gloves and use extreme caution whenever

installing and handling this product and its accessories

as certain components have sharp edges that can

cause personal injury.

WARNING: NEVER cover more than 75% of the cooking surface with griddles or pans. Overheating will occur,

and burners will not perform properly when combustion heat is trapped below the cooking surface.

IMPORTANT

IN THE EVENT OF A GREASE FIRE, IMMEDIATELY SHUT OFF THE MAIN GAS VALVE TO THE UNIT. ALLOW THE FIRE

TO EXTINGUISH ITSELF. KEEP AT A SAFE DISTANCE. A THOROUGH INSPECTION BY A QUALIFIED PROFESSIONAL

SERVICE TECHNICIAN SHOULD BE CONDUCTED BEFORE FUTURE USE OF YOUR UNIT. THE SERVICE TECHNICIAN

WILL CHECK THE SYSTEM FOR GAS LEAKS AND WILL CHECK ALL ELECTRICAL WIRING FOR DAMAGE. ALL

GAS LEAKS AND WIRING MUST BE REPAIRED PRIOR TO FUTURE USE.

ELECTRICAL CONNECTIONS

A 120VAC (15 AMP minimum) GFCI GROUNDED 3-wire receptacle (not included) is required within

the vicinity of the unit to provide power to it. The GFCI receptacle must be a WEATHER-PROOF IN-USE

COVERED RECEPTACLE.

• Observe the National Electric Code and all local codes.

• Verify proper polarity of the receptacle.

• If an extension cord is used, ensure it is a 3-wire GROUNDED cord that is rated for the power of the

equipment, and is approved for outdoor use with a W-A marking. DO NOT use 2-prong adapters.

• DO NOT TAMPER WITH THE EXTENSION CORD OR THE UNIT POWER-SUPPLY CORD.

Important: ONLY REPLACE THE INTERIOR OVEN LIGHTS WITH 12V / 10 WATT HALOGEN BULB(S).

The unit serial number tag can be found afﬁxed to the griddle body behind the control panel (on an

aluminum tag) and on the underside of the drip tray handle (on a thermal label). It is recommended

that the drip tray ﬁrst be removed and cleaned / emptied of its contents, then turned over to view.

The unit rating label is located inside of the control panel.

INSTALLATION, OPERATION, AND SAFETY INFORMATION

5

WARNING

This appliance MUST be installed and operated according to the information below.

FAILURE TO PROPERLY VENT THE GRIDDLE CABINET MAY RESULT IN A FIRE OR EXPLOSION CAUSING

PROPERTY DAMAGE, BODILY INJURY, OR DEATH.

A leaking gas connection or valve unintentionally left open will create a hazard.

WHEN USING PROPANE GAS

• Propane gas (also known as L.P. gas) is heavier than air and will accumulate or pool in an inadequately

vented enclosure or recessed area.

• If a pool of propane gas is ignited, an explosion will occur. Adequate venting at the ﬂoor level of the cabinet

eliminates this danger.

• DO NOT store a spare propane-gas cylinder in or near the unit.

WHEN USING NATURAL GAS

• Natural gas is lighter than air and will accumulate at the top of an inadequately vented enclosure.

• If an accumulation of natural gas is ignited, an explosion will occur. Adequate venting at the top of the cabinet

eliminates this danger.

INSTALLATION SAFETY GUIDELINES

THIS UNIT MUST BE INSTALLED SO THAT THE VENT OPENINGS ON THE CABINET REMAIN CLEAR AND

FREE AT ALL TIMES.

The gas cylinder, regulator, and rubber hose must be in a location not subject to temperatures above

125° F (51° C).

IF A PROPANE CYLINDER IS INSTALLED INSIDE OF THE CABINET, THE GUIDELINES FOUND IN THE SAFE

USE & MAINTENANCE OF PROPANE GAS CYLINDERS SECTION MUST BE FOLLOWED.

WHEN OPERATING THIS GAS APPLIANCE, ALL INSTRUCTIONS AND WARNINGS

MUST BE OBSERVED. FAILURE TO DO SO MAY RESULT IN A FIRE OR EXPLOSION

CAUSING PROPERTY DAMAGE, BODILY INJURY, OR DEATH.

Every time you use the unit, make sure that:

1. The area around the unit is clear and free from combustible materials, gasoline and ﬂammable vapors/liquids.

2. There is no blockage of the airﬂow through the vent openings located on the cabinet.

3. The hose is inspected (if applicable). See SAFE USE & MAINTENANCE OF PROPANE-GAS CYLINDERS section.

DO NOT store any combustible materials, gasoline, and any other ﬂammable vapors/liquids in the vicinity of the

unit. Provide adequate clearance for servicing and operation.

GAS SAFETY INFORMATION

OPERATING THE UNIT SAFELY AND CORRECTLY

6

U

L

Fig. 6-1 type coupleur de ﬁl de point culminant d’I

Valve

de

décompression

QCC

Type 1

Valve

Ajustage de précision

en laiton de ﬁl de

point culminant

Indicateur

de niveau

de liquide

(facultatif)

Écrou de main avec le

ﬁl de point culminant.

Régulateur

Passage

Tuyau

Volant de commande

main dans le sens des aiguilles d’une montre pour engager les

ﬁls et pour serrer jusqu’à ce que douillettement. L’utilisation des

pinces ou de la clé ne devrait pas être nécessaire. Seulement

le propane marqué par cylindres doit être employé.

Pour débrancher: Tournez l’écrou de main dans le sens

contraire des aiguilles d’une montre jusqu’à isolé (ﬁg. 6-1).

Important: Avant d’employer le unité, et ensuite chaque

fois que le cylindre est enlevé et rattaché,

examinez tous les raccordements pour

déceler les fuites. Arrêtez les valves de unité

et ouvrez la valve principale de cylindre, puis

vériﬁez les raccordements avec de l’eau

savonneux. Réparez toutes les fuites avant

d’allumer le unité.

ATTENTION: Tournez toujours la valve principale de cylindre

de propane au loin après chaque utilisation,

et avant de déplacer le unité et le cylindre, ou

débrancher l’accouplement. Cette valve doit

rester fermée et le cylindre a débranché alors

que l’appareil n’est pas en service, quoique

l’écoulement de gaz soit arrêté par un dispositif

de sûreté quand le coupleur est débranché.

Inspectez soigneusement l’ensemble de tuyau chaque fois

avant que le gaz soit allumé. Un tuyau ﬁssuré ou efﬁloché doit

être immédiatement remplacé.

Si l'appareil est stocké à l'intérieur, le cylindre doit être disconnected

et a enlevé. Des cylindres Disconnected doivent être stockés

dehors, hors de la portée des enfants, avec les prises de valve

ﬁletées étroitement installées, et ne doivent pas être stockés dans

un bâtiment, le garage, ou n'importe quel autre secteur inclus.

POUR VOTRE SÛRETÉ

a. Ne stockez pas un cylindre de gaz disponible de propane

dessous ou ne vous approchez pas de cet appareil.

b. Ne remplissez jamais cylindre au delà de 80 pour cent de

plein.

c. SI L’INFORMATION DANS “A” ET “B” N’EST PAS SUIVIE

EXACTEMENT, UN FEU CAUSANT LA MORT OU DES

DOMMAGES SÉRIEUX PEUT SE PRODUIRE.

IMPORTANT POUR VOTRE SÛRETÉ

LISEZ ET SUIVEZ TOUS LES AVERTISSEMENTS ÉQUIPÉS DE VOTRE CYLINDRE DE GAZ DE PROPANE.

En actionnant cet appareil avec un cylindre de gaz de propane ON DOIT observer ces instructions et avertissements.

LE MANQUE DE FAIRE AINSI PEUT AVOIR COMME CONSÉQUENCE UNE INCENDIE OU UNE EXPLOSION SÉRIEUSE.

CYLINDRE ET CONDITIONS ET

CARACTÉRISTIQUES DE CONNECTEUR

a. Les bouteilles, les vannes et les tuyaux de propane doivent

être entretenus et inspectés avant chaque utilisation. Ils

doivent être remplacés en cas de dommages visibles. Si

le tuyau est coupé ou présente des signes d’abrasion ou

d’usure, il doit être remplacé avant utilisation (voir e.).

b. Cette unité, lorsqu'elle est utilisée avec une bouteille, doit

être connectée à une bouteille standard de gaz propane de

5 gallons (20 lb) équipée d'un dispositif anti-débordement

répertorié. L’appareil est obligatoire sur toutes les bouteilles

vendues depuis le 1er octobre 1998 aﬁn d’empêcher tout

remplissage excessif.

c. Les dimensions du cylindre doivent être d'environ 12 "(30,5 cm)

de diamètre et 18" (45,7 cm) de hauteur. Les bouteilles doivent

être construites et marquées conformément aux spéciﬁcations

du ministère des Transports (DOT) pour les bouteilles à gaz LP

ou à la norme relative aux bouteilles, sphères et tubes pour le

transport des marchandises dangereuses et à la Commission,

CAN / CSA-B339, selon le cas.

d. Le cylindre doit inclure un collier pour protéger la valve

de cylindre et le circuit d’alimentation de cylindre doit être

assuré le retrait de vapeur.

e. Le montage du régulateur de pression et le ﬂexible (Fig. 6-1)

fourni avec cet appareil au gaz en plein air (modèles au

propane seulement) doit être utilisé. Assemblées d'origine et

régulateur de pression et le tuyau de remplacement doivent

être ceux spéciﬁés par le fabricant pour le raccordement d'un

dispositif de cylindre de liaison identiﬁée comme de type I

par le ANSI Z 21.58/CGA 1.6 (voir liste des pièces pour les

informations de commande).

f. La valve de cylindre de gaz de propane doit être équipée

d’un dispositif d’accouplement de raccordement de

cylindre, décrit comme type I dans la norme déﬁnie dans le

e. de paragraphe ci-dessus. Ce dispositif est généralement

décrit comme coupleur de ﬁl de point culminant.

g. Si votre cylindre de gaz de propane vient avec une prise

de la poussière, placez le bouchon anti-poussière sur la

sortie de valve de cylindre toutes les fois que le cylindre

n’est pas en service.

OPÉRATION DE COUPLEUR

Pour relier le regulator/hose à l’ajustage de précision de

valve de cylindre de gaz de propane: Serrez l’écrou de main

sur le régulateur au-dessus de l’ajustage de précision de ﬁl

de point culminant sur la valve de cylindre. Tournez l’écrou de

1

2

3

4

FIXATION DU CYLINDRE DE GAZ DE PROPANE

1. Soulevez la poignée de

verrouillage pour ouvrir

le plateau et pour tirer à

l’extérieur.

3. Avec le cylindre de gaz en place et relié,

glissez le plateau de nouveau dans la poignée

de verrouillage de chariot et de serrure en

poussant fermement en bas.

2. Placez le cylindre de gaz de propane gainent fermement sur

le plateau avec la base insérée dans le trou central et le collier

s’ouvrant au dos. Suivez les instructions de relier ci-dessus

l’approvisionnement.

Fig. 6-2

Fig. 6-3

Fig. 6-5

Fig. 6-4

Ouverture

de Collier

UTILISATION SÛRE ET ENTRETIEN DES CYLINDRES DE GAZ DE PROPANE

7

U

L

Fig. 7-1 Type I Acme thread coupler

Pressure

relief

valve

QCC

Type 1

valve

Brass Acme

thread ﬁtting

Liquid level

indicator

(optional)

Hand nut with Acme

thread

Regulator

Vent

Hose

Hand wheel

The use of pliers or a wrench should not be necessary. Only

cylinders marked “propane” may be used.

To disconnect: Turn the hand nut counterclockwise until

detached (Fig. 7-1).

Important: Before using the unit, and after each time

the cylinder is removed and reattached,

check the hose for wear (see a.) and check

all connections for leaks. Turn off the unit

valves and open the main cylinder valve,

then check connections with soapy water.

Repair any leaks before lighting the unit.

CAUTION: Always turn the propane cylinder main valve

off after each use, and before moving the unit

and cylinder or disconnecting the coupling.

This valve must remain closed and the

cylinder disconnected while the appliance

is not in use, even though the gas ﬂow is

stopped by a safety feature when the coupler

is disconnected.

Carefully inspect the hose assembly each time before the

gas is turned on. A cracked or frayed hose must be replaced

immediately.

If the appliance is stored indoors, the cylinder must be

disconnected and removed. Disconnected cylinders must be

stored outdoors, out of the reach of children, with threaded

valve plugs tightly installed, and must not be stored in a

building, garage, or any other enclosed area.

FOR YOUR SAFETY

a. DO NOT store a spare propane-gas cylinder under or

near this appliance.

b. NEVER ﬁll the cylinder beyond 80-percent full.

c. IF THE INFORMATION IN a. AND b. IS NOT FOLLOWED

EXACTLY, A FIRE CAUSING DEATH OR SERIOUS

INJURY MAY OCCUR.

IMPORTANT FOR YOUR SAFETY

READ AND FOLLOW ALL WARNINGS PROVIDED WITH THE PROPANE-GAS CYLINDER.

When operating this appliance with a propane-gas cylinder, these instructions and warnings MUST be observed.

FAILURE TO DO SO MAY RESULT IN A SERIOUS FIRE OR EXPLOSION.

CYLINDER/CONNECTOR REQUIREMENTS

a. Propane-gas cylinders, valves, and hoses must be

maintained in good condition and inspected before each use

of appliance. They must be replaced if there is any visible

damage. If hose is cut or shows excessive abrasion or wear,

it must be replaced before using appliance (see e.).

b. This unit, when used with a cylinder, should be connected

to a standard 5-gallon (20 lb.) propane-gas cylinder

equipped with a listed overﬁlling prevention device. The

device has been required on all cylinders sold since

October 1,1998, to prevent overﬁlling.

c. Cylinder dimensions should be approximately 12" (30.5

cm) in diameter and 18" (45.7 cm) high. Cylinders must

be constructed and marked in accordance with the U.S.

Department of Transportation (D.O.T.) Speciﬁcations for

LP-Gas Cylinders, or the Standard for Cylinders, Spheres,

and Tubes for Transportation of Dangerous Goods and

Commission, CAN/CSA-B339, as applicable.

d. The cylinder used must include a collar to protect the

cylinder valve, and the cylinder supply system must be

arranged for vapor withdrawal.

e. The pressure regulator and hose assembly (Fig. 7-1)

supplied with this outdoor gas appliance (L.P. models

only) must be used. Original and replacement pressure

regulator and hose assemblies must be those speciﬁed by

the manufacturer for connection with a cylinder connecting

device identiﬁed as Type I by the ANSI Z 21.58/CGA 1.6

(see PARTS LIST for ordering information).

f. The propane-gas cylinder valve must be equipped with

a cylinder connection device, described as Type I in the

standard deﬁned in paragraph e. above. This device is

commonly described as an Acme thread coupler.

g. If the propane-gas cylinder comes with a dust plug, place

the dust cap on the cylinder valve outlet whenever the

cylinder is not in use.

COUPLER OPERATION

To connect the regulator/hose assembly to the propane-

gas cylinder valve ﬁtting: Press the hand nut on the regulator

over the Acme thread ﬁtting on the cylinder valve. Turn the hand

nut clockwise to engage the threads and tighten until snug.

SECURING THE PROPANE-GAS CYLINDER

1. Lift latch handle to unlock

tray and pull outward.

3. With gas cylinder in place and connected, slide

tray back into cart and lock latch handle by

pushing ﬁrmly downward.

2. Set propane-gas cylinder into the sleeve of the extended tray with

base inserted into center hole and collar opening to back. Follow

instructions above to connect supply.

Collar

Opening

Fig. 7-2

Fig. 7-3

Fig. 7-5

Fig. 7-4

SAFE USE & MAINTENANCE OF PROPANE GAS CYLINDERS

8

Installation must be performed by a qualiﬁed professional

service technician.

This unit is designed for outdoor use only. DO NOT use this

unit inside a building, garage, or enclosed area. DO NOT use

this unit in or on a recreational vehicle or boat.

OVERHEAD CONSTRUCTION AND EXHAUST

HOOD REQUIREMENTS

A minimum 5 foot clearance is required between the cooking

surface and the overhead construction.

When installed under combustible overhead construction,

the area above the cooking surface of the unit must be

covered with an exhaust hood. The exhaust hood provides

the protection for the combustible overhead construction.

See exhaust hood information below and Fig. 8-1.

Important: DO NOT use this appliance under unprotected

combustible overhead construction.

When installed under overhead non-combustible construction,

an exhaust hood is highly recommended; see exhaust hood

information below and Fig. 8-1.

Exhaust Hood

When using an exhaust hood, the area above the cooking

surface of the griddle must be covered with a hood larger

than the cooking area of the griddle, and with a minimum

of 1200 CFM (cubic feet per minute) rated exhaust fan for

proper outdoor application.

INSTALLATION REQUIREMENTS

Fig. 8-1 Overhead requirements

Min.

5'

OVERHEAD CONSTRUCTION

EXHAUST

HOOD

Combustible overhead

construction:

Exhaust hood required

Non-combustible

overhead construction:

Exhaust hood highly recommended

N

O

N

C

O

M

B

U

S

T

I

B

L

E

W

A

L

9

REAR WALL CLEARANCES

For the minimum clearances between the unit and rear walls,

your setup must fall within one (or more) of the following:

A. Clearance between unit and strictly non-combustible

rear wall

(i.e. brick wall, see Fig. 9-1)

• The unit must have a minimum clearance of 4" from

the non-combustible rear wall.

(To allow for proper ventilation and prevent dangerous

overheating.)

B. Clearance between unit and a protected combustible

rear wall

(i.e. a non-combustible wall in front of a combustible wall

to serve as a barrier. This can be accomplished by brick,

or a metal stud ﬁnished with non-combustible substrate,

see Fig. 9-2)

• The unit must have a minimum clearance of 14" from

the protected combustible rear wall.

(The 4" non-combustible material plus an additional 10"

clearance between the unit and protected rear wall.)

C. Clearance between unit and combustible rear wall

• The unit must have a minimum clearance of 18" from

the combustible rear wall (see Fig. 9-3).

SIDE WALL / CORNER WALL CLEARANCES

(if applicable)

The unit must have a minimum clearance of 24" from any

side walls (to account for variables in airﬂow that could affect

performance). See Fig. 9-4.

INSTALLATION REQUIREMENTS (Cont.)

Fig. 9-3 Clearance 'C' Diagram

Combustible

Min.

18"

(Clearance required for

rear wall)

Fig. 9-1 Clearance 'A' Diagram

Non-combustible

Min.

4"

(Clearance required for

rear wall)

Fig. 9-2 Clearance 'B' Diagram

Min.

14"

Non-combustible

substrate

Non-combustible 4"

Com-

bustible

(Clearance required for

rear wall)

Fig. 9-4 Side/corner wall clearance

Min.

24"

10

The control panel MUST remain removable for servicing (see

CONTROL PANEL REMOVAL section).

COMBUSTION AIR AND COOLING AIRFLOW

Proper airﬂow (front-to-back, Fig. 10-1) MUST be maintained

for the unit to perform as it was designed. If airﬂow is blocked,

overheating and poor combustion will result. Do not block the

1" front air inlet along the bottom of the control panel.

CAUTION: Wind blowing into or across the rear vent (Fig.

10-3) can cause poor performance and/or

dangerous overheating. Orient the griddle so

that the prevailing wind blows toward the front

of the griddle (Fig. 10-2).

GAS-SUPPLY PLUMBING REQUIREMENTS

For natural gas or a household propane system, rigid

1

/

2

" or

3

/

4

" black steel pipe or local code-approved pipe is required

to conduct the gas supply to the unit. Contact your local gas

supplier. Connect this pipe to the C.S.A.-approved quick

connect hose (attached). Apply only joint compounds that are

resistant to all gasses on all NPT pipe ﬁttings except ﬂare

ﬁttings. Make sure to tighten all ﬁttings securely.

Note: If

1

/

2

" pipe is used with natural gas, it should be

no longer than 20'.

Important: A shut-off valve (not included) in the gas

line is required. It provides for safety when

the unit is not in use and for convenient

maintenance and repair. It must be installed

within 6 feet of the unit. Use a pipe joint

compound resistant to all gasses on all male

ﬁttings except ﬂare ﬁttings.

GAS SUPPLY AND MANIFOLD PRESSURES:

For natural gas - normal 7" water column (w.c.), minimum

5", maximum 10

1

/

2

". For propane gas - normal 11" w.c.,

minimum 10", maximum 13".

INSTALLATION REQUIREMENTS (Cont.)

Fig. 10-1 Airﬂow diagram

(1" front air inlet)

CORRECT

Fig. 10-2 Airﬂow direction - CORRECT

PLACE GRIDDLE SO

PREVAILING WIND BLOWS

TOWARD FRONT OF GRIDDLE

YOU MUST PROTECT REAR

VENT FROM PREVAILING WIND

INCORRECT

Fig. 10-3 Airﬂow direction - INCORRECT

11

• To protect against electric shock, do not immerse cord or plugs in water or other liquid.

• Unplug from the outlet when not in use and before cleaning. Allow to cool before putting on or taking off parts.

• Do not operate any outdoor cooking gas appliance with a damaged cord, plug, or after the appliance

malfunctions or has been damaged in any manner. Contact the manufacturer for repair.

• Do not let the cord hang over the edge of a table or touch hot surfaces.

• Do not use an outdoor cooking gas appliance for purposes other than intended.

• When connecting, ﬁrst connect plug to the outdoor cooking gas appliance then plug appliance into the outlet.

• Use only a properly wired and inspected 120VAC (15 AMP minimum) Ground Fault Circuit Interrupter

(GFCI) GROUNDED 3-wire receptacle with this outdoor cooking gas appliance.

• The GFCI receptacle must be a WEATHER-PROOF IN-USE COVERED RECEPTACLE.

• Never remove the grounding plug or use with an adapter of 2 prongs.

• Use only extension cords with a 3 prong grounding plug, rated for the power of the equipment, and approved

for outdoor use with a W-A marking.

• The provisions of the National Electric Code as well as any local codes must be observed when

installing the product.

ELECTRICAL SAFETY

12

MODEL SPECIFICATIONS

E660s Griddle

Main burner quantity

N/P oriﬁce drill size

2

#44 / #55

Nat to LP conversion kit model # 24336-21

Input electrical requirements

120VAC / 15 AMP minimum / 60 Hz / GFCI outlet

Electrical output

12VAC / 60 Watts

Power supply fuse model # / fuse type

24-B-57 / T6.3AL (250V)

Table 1 - Product Speciﬁcations

H

C

G

E

B

D

A

F

Model

Height Width Depth

Floor to top

of shelf

(C)

Left to right Front to back

With lid

(A)

Without lid

(B)

Cart base

(D)

(with shelves)

Cart base

(G)

Maximum

outer

(H)

Up

(E)

Down

(F)

E660s Griddle

39" 38

1

/2" 37" 34

1

/4" 73

1

/2" 44

1

/4" 26" 32"

Table 2 - Griddle Dimensions

13

MODEL SPECIFICATIONS (cont.)

Power supply

Wire harness

extension

Valve

manifold

Light

switch

Burner

igniters

Main

burner 1

Main

burner 2

LED disc

Note: In addition, a wire diagram can be found afﬁxed

to the inside of the control panel.

Power supply

fuse

Wire harness

assembly

LED disc

PORTABLE GRIDDLE WIRING DIAGRAM

14

1

2

24

6

3

7

Fig. 14-1

4

12

13

14

16

17

25

5

10

IMPORTANT

Remove all packing

material (including

any protective

coatings) and

discard prior to use.

SOME COMPONENTS

ARE HEAVY

HANDLE WITH CARE

To order replacement

parts, contact your

local Fire Magic

®

dealer.

GRIDDLE REPLACEMENT PARTS LIST

11

26

27

29

9

11

23

15

GRIDDLE REPLACEMENT PARTS LIST (cont.)

E660s Griddle

Item Description Part No. Qty.

1. Griddle lid 3655 1

2. Griddle top assembly 24194-50 1

3. Rear exhaust plate 24194-55 1

4. Heat distribution grid (set of 2) 3057-S-2 1

5. Main burner 3041-60 2

6. Convertible regulator PR-4 1

7. Valve manifold 24194-51 1

8. Tool holder * 25387-12 1

9. Paper towel holder 25387-11 1

10. Air bafﬂe 24194-41 1

11. Folding shelf 24336-18 2

12. Control panel w/ raceway and wire harness 24194-57 1

13. Control knob 24182-71 2

14. LED disk 24182-63 2

15. Drip tray 24194-58 1

16. Drip collector trough (left and right) 24194-53 1

17. Drip tray chute 24194-54 1

18. Wire harness w/ raceway * 24182-73 1

19. Wire harness extension * 24182-74 1

20. Main burner electrode * 3199-72 2

21. Natural gas oriﬁce * 3001-44-1 2

22. Propane gas oriﬁce * 3001-55-1 2

23. Light switch 24182-48 1

24. Lighting tube (left) 24182-75 1

25. Lighting tube (right) 24182-76 1

26. Propane tank tray (propane models only) 24336-36 1

27. Propane regulator with hose (propane models only) 5110-07 1

28. Quick-disconnect hose (natural models only) * 5110-03 1

29. Power supply 24187-64 1

30. Power supply fuse * 24-B-57 1

*

Not shown

16

LOCATION PREPARATION

Prepare a ﬂat, level surface capable of supporting the weight

of the unit and convenient to the gas supply if connecting

to a gas line.

WHEELS AND CASTERS

To lock a caster press down on the side of the lever with the

word "ON" stamped on it until it stops and the caster will

not turn. To unlock, press down on the side stamped "OFF."

REMOVE PACKAGED CONTENTS AND GRIDDLE TOP

1. Remove all contents from the box.

CAUTION: THE UNIT IS HEAVY AND REQUIRES TWO

PEOPLE FOR SAFE HANDLING.

2. Remove the griddle top by lifting the griddle upward

and out from the main frame. Carefully rest on a sturdy

surface.

Note: Lift the griddle top from the left and right raised walls.

See Fig. 16-2.

CAUTION: THE GRIDDLE TOP IS HEAVY.

3. Remove all packaged contents within the unit and set

aside for later installation.

INSTALL THE TOOL HOLDER AND PAPERTOWEL

HOLDER

The rectangular mounting bracket for the tool holder and

the paper towel holder come pre-attached to the sides of

the cart.

Unpack the holder portion, squeeze the open ends together

slightly, and install them into the mounting bracket (see Fig.

16-3). Next, release the hanger so that the ends extend out

through the holes in the top and bottom of the mounting

bracket (Fig. 16-4, 16-5).

When not in use, the racks may be folded back against the

wall of the cabinet (Fig. 16-4, 16-5).

INSTALLATION

Fig. 16-1 Lock/unlock wheels

Fig. 16-4 Tool holder detail

Fig. 16-5 Papertowel holder detail

Fig. 16-3 Install tool holder / papertowel holder

Fig. 16-2 Remove griddle top

Lift from

side walls

Installation continued on following page

17

CONNECT THE GAS SUPPLY

For connecting a propane unit to a portable propane tank,

read the safety warnings and follow the instructions in the

section SAFE USE AND MAINTENANCE OF PROPANE

GAS CYLINDERS.

For household propane or natural gas units:

1. Turn OFF the gas supply at the source. The quick

disconnect hose is pre-installed on the valve manifold

at the manufacturer. Run the hose through the hole

in the bottom rear of the cabinet, to the gas supply.

2. A shut-off valve is required within 6 feet of the unit.

Connect the quick connect hose to the shut-off valve

OR gas supply (NPT) using a pipe joint compound

resistant to all gasses (see Fig. 17-1). Tighten securely.

3. Turn all burner valves to the OFF position. Turn the gas

supply on. Then carefully check all gas connections

for leaks with a brush and soapy water before lighting.

NEVER USE A MATCH OR OPEN FLAME TO TEST

FOR LEAKS.

LIGHTING TEST

Prior to proceeding with installation, perform a lighting test.

1. Ensure the interior of the griddle is free of any packaging/

plastic material.

2. Test each burner (see the LIGHTING INSTRUCTIONS

section for lighting your burners).

Note: At this point of installation the power is not

connected, so manual lighting (with a match or

lighter) is required.

3. Refer to the AIR SHUTTER ADJUSTMENT section to

determine if the burners require air shutter adjustments.

4. Allow the unit to completely cool after testing.

REPLACE GRIDDLE TOP ASSEMBLY

1. Carefully place the griddle top back onto the main

frame.

Note: Lift the griddle top from the left and right raised

walls (see Fig. 17-2).

CAUTION: THE GRIDDLE TOP IS HEAVY AND

REQUIRES TWO PEOPLE FOR SAFE

HANDLING.

2. Secure the griddle top by fastening the provided screw

into the screw hole located on the rear of the griddle

top (see Fig. 17-3).

INSTALLATION (cont.)

Fig. 17-2 Replace griddle top

Fig. 17-3 Secure griddle top

Lift from

side walls

Griddle top

rear wall

(Rear view)

Fig. 17-5 Connecting to a gas line

Gas supply (NPT)

Quick

connect hose

(coming from unit)

NPT-to-NPT

shut-off valve

(required, not included,

must be installed within

6 feet of the unit)

Quick connector

(can be connected

directly to gas supply

stub if shut-off valve

installed in-line)

18

INSTALLATION (cont.)

INSTALL REAR EXHAUST PLATE

1. Assemble the provided bolts and nuts (loosely) to

the three holes on the rear exhaust plate as shown

in Fig. 18-1, A.

2. Align the exhaust plate with the three cutouts on

the griddle rear wall and fasten (see Fig. 18-1, B).

INSTALL THE DRIP COLLECTOR TROUGH

1. Place the left piece inside the griddle drip reservoir

and completely slide it to the left side (see Fig.

18-2,A).

2. Place the right piece and ensure it overlaps the left

tray as shown in Fig. 18-2, B.

INSTALL THE DRIP TRAY

Carefully align the drip tray to the opening found on the

bottom front of the control panel and fully insert (see

Fig. 18-3).

Fig. 18-1 Install rear exhaust plate

Rear exhaust

plate

A

B

Griddle

rear wall

Assemble bolts

and nuts

Secure to

griddle rear wall

Fig. 18-2 Install drip collector trough

Fig. 18-3 Install drip tray

A

B

Overlap

19

Fig. 19-1 E660s Griddle controls

* The light switch is push button operated, and is located on the right

side of the control panel. It controls the power to the lighted knobs.

Lighting

tube (left)

Lighting

tube (right)

Right

main burner

control knob

Light

switch*

Left

main burner

control

knob

Control

panel

screw(s)

Burner ﬂame

viewing cutouts

Drip tray

IDENTIFICATION OF GRIDDLE CONTROLS

USE, CARE, & SERVICE

20

BEFORE INITIAL USE

Ensure that:

• the unit has been properly installed and leak tested by a qualiﬁed professional service technician and as instructed in this manual.

• you have read and understand all of the information in this manual.

BEFORE EACH USE

Ensure that:

• you smell around the appliance area for gas. If you smell gas (and all control knobs are in the OFF position), immediately shut

off the gas supply and contact a qualiﬁed professional service technician or the gas supplier for inspection.

• the vent openings and surrounding area of the unit are clear and free at all times.

• the cooking area, drip tray, and drip collector trough are clean, and the drip tray and drip collector trough are properly installed.

• you inspect all piping and hoses for damage, cuts, wear, and tear. Replace any damaged components prior to use.

OPERATION

• The unit becomes HOT during use. NEVER touch any part of the cooking area or surrounding hot surfaces with bare

hands. Use long-handled insulated BBQ tools and wear an insulated glove / oven mitt.

• Always keep your face and body as far from the unit as possible during use. Avoid wearing loose-ﬁtting clothing as

they could ignite.

• NEVER leave the unit unattended during use.

• After each use, turn the control knob(s) to the OFF position and turn off the gas supply to the unit.

After reading and understanding all bullets above, follow these steps to light and use your griddle:

1. Remove the griddle lid. The back of enclosure has hooks to hang the lid. When using the

hooks, the lid must hang from the far end of the hooks to maintain proper ventilation when

cooking. See Fig. 20-1.

2. Wipe the cooking surface with a damp clean cloth to remove dust/grime.

3. Coat the cooking surface with a cooking oil or a non-stick cooking spray (high smoking point

and low-sugar content is recommended).

4. Light the griddle per the LIGHTING INSTRUCTIONS section.

5. Turn the control knobs to the HI-LIGHT position and allow the griddle to preheat for 15 minutes.

6. Place the food on the cooking surface and cook as desired. Monitor the ﬂames (through the

burner ﬂame viewing cutouts) and the temperature, and adjust the heat setting if necessary.

Note: Add cooking oil frequently as you cook to ensure the surface remains stick-resistant.

7. See the sections below and the following pages for all other information regarding use.

WIND CONSIDERATIONS

Proper airﬂow (front-to-back, Fig. 20-2) MUST be maintained for the unit to perform as it was

designed. See the INSTALLATION REQUIREMENTS section for details.

When using the unit in windy conditions, the wind can disrupt the airﬂow and cause overheating.

To prevent overheating during windy conditions, do not leave the hood closed with the burners on

high for more than 15 minutes.

AFTER EACH USE

1. Clean the cooking surface, drip collector trough, and drip tray as instructed in the SERVICING

AND CLEANING section.

2. Once the unit has completely cooled, replace the stainless steel griddle lid and cover the entire unit with a griddle cover.

Note: For additional cleaning information, refer to the SERVICING AND CLEANING section.

Fig. 20-1 Hang lid

Fig. 20-2 Airﬂow diagram

Hang

lid from

hooks

Must

retain

air gap

USING THE GRIDDLE

La page charge ...

Fire Magic Echelon Diamond Portable Griddle Manuel utilisateur

Ce manuel convient également à

Fire Magic Echelon Diamond Portable Griddle Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents