iLive ITP180B Manuel utilisateur

Marque: iLive

Modèle: ITP180B

Catégorie: Stations d'accueil pour appareils mobiles

Taper: Manuel utilisateur

USER’S GUIDE

V: 428-02

For the most up-to-date version of this User’s Guide, go to www.iLiveElectronics.com

ITP180B

2.1 Channel Speaker Bar for Any TV

iLive

WARNING: Lithium batteries, like all rechargeable batteries

are recyclable and should be recycled or disposed of in

normal household waste. Contact your local government

for disposal or recycling practices in your area. They should

never be incinerated since they might explode.

WARNING: Shock hazard - Do Not Open.

AVIS: RISQUE DE CHOC ÉLECTRIQUE - NE PAS OUVRIR

Mains Plug or Direct plug-in adapter is used as disconnect

device and it should remain readily operable during

intended use. In order to disconnect the apparatus from the

mains completely, the Mains Plug or Direct plug-in adapter

should be disconnected from the mains socket outlet

completely.

La che d’alimentation ou adaptateur de courant est utilisé

comme dispositif de déconnexion et doit rester accessible

pendant l’utilisation. Pour mettre l’appareil hors tension, la

che ou adaptateur de courant doit être débranché de la prise

de courant.

Do not mix old and new batteries.

Do not mix alkaline, standard (carbon-zinc), or rechargeable

(ni-cad, ni-mh, etc) batteries.

No mezcle baterías viejas y nuevas.

No mezcle baterías alcalinas, estándar (carbono-zinc) o

recargables (ni-cad, ni-mh, etc.).

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE

BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

WARNING: To reduce the risk of re or electric shock, do

not expose this apparatus to rain or moisture.

AVERTISSEMENT: Pour réduire le risque d’incendie ou de

choc électrique, ne pas exposer cet appareil sous la pluie et

l’humidité.

CAUTION: Use of any controls or adjustments or

performance of procedures other than those herein

specied may result in hazardous radiation exposure.

WARNING: Changes or modications to this unit not

expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment.

WARNING: Do not place the unit on top of any soft, porous,

or sensitive surfaces to avoid damaging the surface. Use a

protective barrier between the unit and surface to protect

the surface.

WARNING: Use of this unit near uorescent lighting may

cause interference regarding use of the remote. If the unit is

displaying erratic behavior move away from any uorescent

lighting, as it may be the cause.

CAUTION: Danger of explosion if battery is incorrectly

replaced. Replace only with the same or equivalent type.

PRÉCAUTION: Danger d’explosion si les piles sont remplacées

de façon incorrect. Remplacer les piles seulement par le même

type de pile ou l’équivalent.

WARNING: There is a danger of explosion if you attempt

to charge standard Alkaline batteries in the unit. Only use

rechargeable NiMH batteries.

WARNING: The battery, batteries, and battery pack shall

not be exposed to excessive heat such as sunshine, re, or

the like.

The lightning ash with arrowhead symbol, within

an equilateral triangle, is intended to alert the user

to the presence of uninsulated "dangerous voltage"

within the product's enclosure that may be of

sufcient magnitude to constitute a risk of electric

shock to persons.

WARNING: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER (OR BACK). NO USER-

SERVICEABLE PARTS INSIDE. REFER

SERVICING TO QUALIFIED SERVICE

PERSONNEL.

ATTENTION

RISQUE D' ÉLECTROCUTION

NE PAS OUVRIR

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

The exclamation point within an equilateral triangle

is intended to alert the user to the presence of

important operating and maintenance (servicing)

instructions in the literature accompanying the

appliance.

Warnings and Precautions

Customer Support: 1-888-999-4215 iLive

13. Unplug this apparatus during lightning storms or when

unused for long periods of time.

14. Refer all servicing to qualied service personnel.

Servicing is required when the apparatus has been

damaged in any way, such as power-supply cord or

plug is damaged, liquid has been spilled or objects

have fallen into the apparatus, the apparatus has been

exposed to rain or moisture, does not operate normally,

or has been dropped.

1. Read these Instructions.

2. Keep these Instructions.

3. Heed all Warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with a dry cloth.

7. Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators,

heat registers, stoves, or other apparatus (including

ampliers) that produce heat.

9. Do not defeat the safety purpose of the polarized or

grounding - type plug. A polarized plug has two blades

with one wider than the other. A grounding type plug

has two blades and a third grounding prong. The wide

blade or the third prong are provided for your safety.

When the provided plug does not t into your outlet,

consult an electrician for replacement of the obsolete

outlet.

10. Protect the power cord from being walked on or

pinched particularly at plugs, convenience receptacles,

and the point where they exit from the apparatus.

11. Only use attachments/accessories specied by the

manufacturer.

12.

This symbol indicates that this product

incorporates double insulation between

hazardous mains voltage and user

accessible parts.

Use only with a cart, stand, tripod,

bracket, or table specied by the

manufacturer, or sold with the apparatus.

When a cart is used, use caution when

moving the cart/apparatus combination to

avoid injury from tip-over.

Important Safety Instructions

Special note: When placing your unit on a lacquered or

natural nish, protect your furniture with a cloth or other

protective material.

WARNING: Changes or modications to this unit not expressly

approved by the party responsible for compliance could void the

user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with

the limits for a Class B digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This

equipment generates, uses, and can radiate radio frequency energy

and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning

the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

The apparatus shall not be exposed to dripping or

splashing and that no objects lled with liquids, such as

vases, shall be placed on apparatus.

L’appareil ne doit pas être exposé aux écoulements ou aux

éclaboussures et aucun objet ne contenant de liquide, tel

qu’un vase, ne doit être placé sur l’objet.

Battery shall not be exposed to excessive heat such as

sunshine, re or the like.

Les piles ne doivent pas être exposées à de forte chaleur,

tel qu’à la lumière du soleil, au feu ou autres choses de

semblable.

Caution marking is located at the rear or back of the

apparatus.

Attention marquage est situé à l’arrière ou à l’arrière de

l’appareil

The marking information is located at the rear or back of

apparatus.

Les informations de marquage est situé à l’arrière ou à

l’arrière de l’appareil.

FCC Warnings

Additional Warnings

iLive

2.1 Channel Speaker Bar for Any TV

• Powered 2.1 channel

speaker system with built-in

subwoofer

• App-enhanced

• Motorized dock plays &

charges iPod & iPhone

• FM radio with 20 station

presets

• RCA audio input

• 3.5mm Audio Input

• Optical audio Input

• Component video output

• Subwoofer output

• Advanced remote control

• 30” length

• Wall mountable

• Treble & bass controls

• 5 EQ presets

• Digital clock

• Wake to iPod/iPhone or radio

• Gradual wake

• Sleep timer

• AC power: built-in AC power

cord

• Remote control: requires 2

AAA batteries (included)

• Docking brackets for

compatible iPhone/iPod

models

• FM wire antenna

• Component video & audio

cable

• Wall-mount hardware & easy

mount instructions

Features

Includes

Setup

AC power: built-in AC power cable Requires 2 AAA batteries (included)

FM ANT

OUT

COMPENTENT OUT VIDEO

AUDIO IN

SW OUT

RESET

AC 120V/60Hz

OPTICAL

Power Remote

Customer Support: 1-888-999-4215 iLive

Table of Contents

Warnings and Precautions ............................................................................ 2

Important Safety Instructions ......................................................................... 3

2.1 Channel Speaker Bar for Any TV ................................................................... 4

Setup ................................................................................................ 4

Table of Contents ..................................................................................... 5

Introduction ......................................................................................... 6

iPod and iPhone ...................................................................................... 8

Dock + App .......................................................................................... 9

FM Radio ...........................................................................................10

Clock, Alarm, and Sleep Timer ........................................................................ 11

Basic Connectivity ................................................................................... 12

Video Output .......................................................................................13

Audio Inputs and Subwoofer Output .................................................................14

Mounting to a Wall ..................................................................................15

Company Information ...............................................................................16

iLive

Introduction

POWER

SOURCE

VOLUME

PLAY/PAUSE

LINE IN

iPod DRAWER

OPTICAL

POWER

Press to turn the bar

speaker o or on.

SOURCE

Press to switch between

Opitcal, AUX, Line, FM,

and iPhone/iPod modes.

VOLUME

Press to adjust the volume.

PLAY/PAUSE

Press to play or pause a

docked iPhone or iPod.

iPod DRAWER

Press to open or close

the motorized dock

for iPhone/iPod.

AC POWER CABLE

3.5MM AUDIO INPUT

RESET

Press using a paperclip

or like object to reset

the bar speaker to it’s

original settings.

OPTICAL

AUDIO INPUT

RCA AUDIO

INPUT

SUBWOOFER

OUTPUT

COMPONENT

VIDEO

OUTPUT

FM ANTENNA

PORT

Customer Support: 1-888-999-4215 iLive

MUTE

Press to mute the volume.

ALARM

With the power o, press

to set the alarm.

CLOCK

With the power o,

press to set the clock.

SLEEP

Press repeatedly to

set the sleep timer.

BASS

With the EQ set to FLAT, press

to adjust the levels of bass.

REV/FWD/MIN/HR

Press to rewind or fast

forward a docked iPhone

or iPod. Press to adjust the

hour and minute when

setting the clock or alarm.

Press skip through menus

on a docked iPhone or iPod.

TUN/SKIP

Press to skip between tracks

on a docked iPhone or iPod.

Press to tune the radio.

ALBUM/CHAPTER/PLAYLIST

Press to skip through albums,

chapters, or playlists on a

docked iPhone or iPod.

SOURCE

Press to switch between

Opitcal, AUX, Line, FM,

and iPhone/iPod modes.

NUMBER KEYPAD

REPEAT

Press to repeat a single

track or entire album on a

docked iPhone or iPod.

TREBLE

With the EQ set to FLAT, press

to adjust the levels of treble.

MENU UP/DN

Press to navigate up and

down in menus on a

docked iPhone or iPod.

SELECT

Press to make selections on

a docked iPhone or iPod.

SHUFFLE

Press to play songs from

a docked iPhone or iPod

in a random order.

Press to adjust the EQ.

VOLUME

Press to adjust the volume.

PLAY/PAUSE

Press to play or pause a

docked iPhone or iPod.

STOP

Press to stop a docked

iPhone or iPod during play.

MEMORY

Press to cycle through

saved radio stations.

iPod

Press to switch to

iPhone/iPod mode.

STANDBY/ON

Press to turn the bar

speaker o or on.

DISPLAY

Press to view the

clock on the display.

iPod DRAWER

Press to open or close

the motorized dock

for iPhone/iPod.

MEM

Press to save a radio

station to the bar

speaker’s memory.

iLive

iPod and iPhone

1. Press the POWER button to turn the bar speaker

on.

2. Press the SOURCE button to switch to iPhone/

iPod mode.

3. Press the iPod DRAWER button to open the

MOTORIZED DOCK FOR iPhone/iPod

4. Locate the numbered bracket that ts the

iPhone/iPod model that will be docked.

Each included bracket has a number on it,

indicating which iPhone/iPod model that bracket

is compatible with. See the separate bracket chart

page to identify which bracket is needed.

5. Snap the bracket into place over the iPhone/iPod

connector in the motorized dock.

6. Connect the iPhone or iPod to the connector

inside the Dock for iPhone/iPod.

When the speaker is plugged in, using AC power, the

docked iPhone or iPod will charge.

After docking an iPod or iPhone, the bar speaker

will automatically switch to composite video

output mode.

1. Follow the instructions for Docking an iPod or

iPhone.

2. Press the PLAY/PAUSE button to begin playing

music from the docked iPhone or iPod.

Docking an iPod or iPhone

Playing a Docked iPod or iPhone

Customer Support: 1-888-999-4215 iLive

Dock + App

1. Go to the App Store on your iPhone, iPod touch,

or on iTunes.

2. Search for Dock + App.

3. Download the App.

When downloading directly from iTunes, sync the

app to your iPod or iPhone from iTunes.

Manually Downloading the App

iLive

FM Radio

Plug the FM Wire Antenna (included) into the FM

Antenna Connection.

1. Press the POWER button to turn the bar speaker

on.

2. Press the SOURCE button to switch to FM radio

mode.

3. Press the TUN/SKIP buttons on the remote to

tune the FM radio.

1. Press the POWER button to turn the bar speaker

on.

2. Press the SOURCE button to switch to FM radio

mode.

3. Press the MEMORY buttons on the remote to

cycle through saved radio stations.

1. Follow the instructions for tuning the FM radio.

2. After tuning to the desired station, press the

MEM button.

3. Press the MENU UP or MENU DN buttons on the

remote to select a preset.

4. Press the MEM button to save the current radio

station to the selected preset.

Up to 20 stations can be saved to the bar speaker’s

memory.

FM Antenna

Tuning the FM Radio

Listening to a Saved Radio Station

Saving a Radio Station

Customer Support: 1-888-999-4215 iLive

Clock, Alarm, and Sleep Timer

1. Press the POWER button to turn the power o.

2. Press the CLOCK button on the remote control.

3. The time on the display will begin blinking.

4. Press the REV/MIN and FWD/HR buttons on the

remote to adjust the minute and hour.

5. Wait 5 seconds to nish setting the clock.

1. Press the POWER button to turn the power on.

2. Press the SOURCE button on the bar speaker to

switch to the desired sleep timer source.

3. Press the SLEEP button repeatedly to set the

sleep timer.

4. After the set sleep time has expired, the bar

speaker will automatically power o.

1. Press the POWER button to turn the power on.

2. Adjust the volume to the desired level.

3. Press the POWER button to turn the power o.

4. Press the ALARM button on the remote control.

5. The alarm time on the display will begin blinking.

6. Press the REV/MIN and FWD/HR buttons on the

remote to adjust the minute and hour.

7. Press the SOURCE button on the bar speaker to

switch to the desired alarm source.

8. Wait 5 seconds to nish setting the alarm.

9. ALARM will appear on the display when the

alarm is set.

10. Press the ALARM button to cancel the alarm.

Setting the Clock

Setting the Sleep Timer

Setting the Alarm

iLive

DVD PLAYER

DIGITAL CABLE or SATELLITE TUNER

VCR

GAMING CONSOLE

SUBWOOFER TELEVISION

IPOD

Basic Connectivity

This is a basic ow chart of how you can connect your home entertainment devices to the bar speaker,

and in turn how the bar speaker connects to them.

For optimal performance, always connect video sources such as a DVD players, gaming consoles or set-top boxes directly

to your television.

Customer Support: 1-888-999-4215 iLive

Video Output

The Component Video Output will only output

video from a docked iPod or iPhone.

1. Connect a component video cable to the

COMPONENT VIDEO OUTPUT and a television.

2. Adjust the connected television

to the proper input setting.

3. Press the SOURCE button on the remote

to switch to iPhone/iPod mode.

4. Video from a docked iPhone/iPod, can

now be played through the bar speaker

to the connected television.

Using the Component Video Output

iLive

Audio Inputs and Subwoofer Output

1. Connect a 3.5mm Audio Input cable (not

included) to the 3.5MM AUDIO INPUT on the

bar speaker and an audio source.

2. Press the POWER button to turn the bar speaker

on.

3. Press the SOURCE button to switch to LINE

mode.

4. Use the native controls on the connected audio

device to begin playing music through the

connected bar speaker.

1. Use an RCA cable (included) to connect an

external subwoofer to the SUBWOOFER

OUTPUT.

2. When audio is played through any source, the

bar speaker will automatically use the connected

subwoofer.

1. Connect an RCA cable (included) to the RCA

AUDIO INPUT on the bar speaker and an audio

source.

2. Press the POWER button to turn the bar speaker

on.

3. Press the SOURCE button to switch to AUX

mode.

4. Use the native controls on the connected audio

device to begin playing music through the

connected bar speaker.

Using the 3.5mm Audio Input

Using the Subwoofer Output

Using the RCA Audio Input

You will need: An audio source with an Optical

Audio Output and a Digital Optical Audio Cable

(not included)

1. Connect the Digital Optical Audio Cable to the

optical output on the audio source and to the

OPTICAL INPUT on the speaker bar.

2. Press the POWER button to power the unit on.

3. Press the SOURCE button repeatedly to swtich

to OPTICAL Mode.

4. Audio from the connected audio source will now

be played through the speakers.

Using the Optical Input

Customer Support: 1-888-999-4215 iLive

Mounting to a Wall

We recommend having this bar speaker

professionally mounted.

The included spacers should be used at your

discretion to extend the face of the bar speaker

farther from the wall. These are typically used when

mounting the bar speaker under a television, and

the face of the bar speaker needs to be ush with the

face of the television.

1. Use the Tape Measure to decide how high you’d

like to hang the bar speaker on the wall.

2. The bar speaker must be hung within 6 feet of an

AC power outlet for the attached AC power cable

to reach.

3. Use the Stud Finder to locate 2 parallel wooden

studs to screw the mounting brackets into.

4. Mark the wall at the center of the studs using the

Pencil.

5. Line the Level up on both of your marks to make

sure they are level. If they’re not, adjust the

marks as needed to make them level.

6. After you’ve double checked your markings, drill

through the top hole on both mounting brackets

directly into the marks you’ve made on the wall.

7. If you are using the brackets only and no spacers,

use the included short screws. If you are using

any of the spacers or combination of the spacers,

use the long screws.

8. Use the Level to level each of the hanging

brackets, then drill the second screw into the

bottom hole on both mounting brackets.

9. Slide the bar speaker onto the mounting

brackets, and make sure there is a rm and stable

connection before letting go of the bar speaker.

10. Finally, use the Level to conrm that the bar

speaker is level.

• Manual or Power Screwdriver

• Stud Finder

• Pencil

• Tape Measure

• Level

• (2) Wall Mount Brackets

• (4) Long Screws

• (4) Short Screws

• (2) 1/4” Spacers

• (2) 1/2” Spacers

• (2) 3/4” Spacers

Important Notes

Getting Started

Required Tools

Included Hardware

16”

ITP180B

screws

studs

mounting

bracket

spacer

Specications are subject to change without notice

iLive ITP180B Manuel utilisateur

Marque: iLive

Modèle: ITP180B

Catégorie: Stations d'accueil pour appareils mobiles

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: iLive ITP180B User manual

iLive ITP180B Manuel utilisateur

iLive ITP180B Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents