Reebok 51549 Manuel utilisateur

Marque: Reebok

Modèle: 51549

Taper: Manuel utilisateur

9/17/2007

REEBOK XL ACTION GRIP

BASKETBALL SYSTEM

MODEL #51549

ASSEMBLY INSTRUCTIONS AND

OWNER’S MANUAL

Save this instruction in the event that

the manufacturer has to be contacted for

replacement parts.

INSTRUCTION #1030931

WARNING

Failure to comply with any of the warnings

in these instructions may result in serious

personal injuries such as cuts, broken

bones, nerve damage, paralysis, brain

injury, or death. Failure to comply may

also result in property damage. Please

heed all warnings and cautions. To ensure

your safety, do not attempt to assemble

this system without reading and following

all instructions carefully. Identify and

inventory the parts using the Parts List.

**U.S. and Canada customers ONLY**

IF ASSISTANCE IS NEEDED,

DO NOT CONTACT THE STORE!!!

CALL OUR CUSTOMER SERVICE DEPARTMENT at 1 (800) 225-3865

HOURS: 7:00 a.m. to 5:00 p.m. Monday through Friday (Mountain Standard Time)

**For customers outside the U.S. or Canada, please contact the store for assistance.**

,IFETIME0RODUCTS¸)NCISTHESOLEDISTRIBUTOROF2EEBOK¸"ASKETBALL

SYSTEMS&ORMOREINFORMATIONVISITUSAT

Copy

HARDWARE IS

ACTUAL SIZE

(Unless otherwise indicated)

PARTS LIST

ID Part # Description Qty

TP 1030702 Top Pole 1

MP 1030703 Middle Pole 1

BP 1030855 Bottom Pole 1

RB 1030781 Right Backboard Bracket 1

LB 1030762 Left Backboard Bracket 1

AT 1030881 Backboard 1

AA 500096 Pole Cap 1

AB 502005 Net 1

AC 502056 Plastic Guard 1

AD 504068 Counterbalance Spring 2

AE 510025 1/2” x 21 3/4” Axle 1

AF CB01599 Base 1

AG 510022 Wheel 2

AH 510035 Base Cap 1

WS FS16400 Warning Sticker ( one Applied) 2

AI F028010 Height Sticker 1

AJ 1030666 Rim 1

AK 1030669 Short Extension Arm 2

AL 1030670 Long Extension Arm 2

AM 1030674 Pole Brace 2

AN DA03800 Rebook Pole Pad 1

Main Hardware (HD9125B)

HA 300022 1/4” Centerlock Nut 2

HB 300029 1/2” x 7 1/8” Hex Bolt 5

HC 300110 1/4” x 2 3/4” Hex Bolt 2

HD 301008 1/2” Centerlock Nut 5

HE 302005 3/8” x 7” Hex Bolt 1

HF 302008 3/8” Centerlock Nut 1

HG 302011 5/16” x 1 1/4” Carriage Bolt 2

HH 302090 5/16” Nylock Flange Nut 2

HI 500013 9/16” x .592” Poly Spacer 4

HJ 500032 1/2” x 1/8” Spacer 4

HK 500037 1/2” x 1” Poly Spacer 2

HL 800324 1/2” x 2 5/16” Metal Spacer 2

Rim Hardware (1012253)

RA 300066 5/16” Hex T-Nut 2

RK 300128 5/16” Jam Nut 2

RC 302014 5/16” Flat Washer 2

RD 302056 Rubber Washer 2

RE 302060 5/16” x 2 1/2” Tap Bolt 2

RF 1009200 4 1/2” U-Bolt 1

HH 302090 5/16” Nylock Flange Nut 4

RJ 1001137 Compression Spring 2

RI 804033 Spring Retainer Plate 1

(Not actual size)

PARTS LIST

ID Part # Description Qty

AN A040031C Inner Channel 1

AO 1030812 Outer Tube 1

AP C050018 Channel Stop 1

AQ 1030748 Pole Bracket 1

AR C050019 Handle 1

AS C050017 Trigger 1

Action Grip

Hardware (HH01300)

GA A070044 Lock Tab 1

GB B070040 1/4-20 x 1 1/2” Screw 2

GC B080015 Trigger Spring 1

GD BW00100 #6 Flat Washer 2

GE 300027 5/16” x 1 3/4” Hex Bolt 1

GF 300031 3/8” Flat Washer 2

GH 300095 5/16” Cap Nut 1

GI 300103 #6 x 3/8” Phillips Screw 2

HF 302008 3/8” Centerlock Nut 2

GK 302053 3/8” x 4” Hex Bolt 2

GL 800239 1/2” x 3 7/16” Spacer 2

Pole Joint Hardware (1005748)

PA BS02000 1/4” x 3/4” Screw 2

PB 1004620 Self-Tapping Screw 2

Base Hardware (1006763)

BA 300066 5/16” Hex T-Nut 1

BB 300030 5/16” x 1” Hex Bolt 2

BD 300097 5/16” Nylock Nut 2

BE BB05300 5/16” x 3.65” Shldr Screw 1

RC 302014 5/16” Flat Washer 4

(Not actual size)

GCGB

(Not actual size)

Failure to follow these safety instructions may result in serious injury or property damage and will void the warranty. The owner must ensure that all players

know and follow these rules for safe operation of the system. Proper and complete assembly, use and supervision is essential for proper operation and to reduce the risk

of accident or injury. A high probability of serious injury exists if this system is not installed, maintained, or operated properly. • If using a ladder during assembly, use

extreme caution. Follow all warnings and cautions on the ladder carefully. • Two people are required for assembly. • Check the Base regularly for leaks. Slow leakage

could cause the system to tip over unexpectedly. • Seat the pole sections properly. Failure to do so could allow the pole sections to separate during play and/or transport

of the system. • Climate, corrosion, or misuse could result in system failure. • If technical assistance is required, contact the manufacturer. • Minimum operational height

is 7’ 6” to the Rim. Most injuries are caused by misuse and/or failure to follow instructions. Use caution when using the system.

SAFETY INSTRUCTIONS

A. Keep the hardware bags and their contents separate. If any parts are missing, call our Customer Service Department.

B. TesttallBoltsbyinsertingthemintotheirrespectiveholes.Ifnecessary,carefullyscrapeawayanyexcesspowdercoatingbuildupfrominsidethe

holes. Do not scrape away all of the powder coating. Bare metal may rust. You may need to pound some Bolts into place with a hammer or mallet.

BEFORE BEGINNING ASSEMBLY

*A MINIMUM OF TWO

ADULTS ARE REQUIRED

FOR ASSEMBLY*

Tools and Materials

Required for Assembly

(Not Included)

1. Adjustable Wrench

2. 7/16” Wrenches (2)

3. 1/2” Wrenches (2)

4. 9/16” Wrenches (2)

5. 3/4” Wrenches (2)

6. Hammer or Mallet

7. 375 lbs. Sand or Water Supply

8. Tape Measure

9. Punch/Dowel or similar tool

10. Scrap Wood or Cardboard

11. Phillips Screwdriver

POLE SECTION IDENTIFICATION

Identify the pole sections before beginning assembly. Failure to assemble

the pole sections correctly may result in severe personal injury or property

damage as described on Page One.

ONCE THE POLE SECTIONS HAVE BEEN SEATED, THEY

CANNOT BE SEPARATED.

Top Pole:

Four holes at the

top of the pole and

one small hole at

the bottom.

Middle Pole:

One slot at the top of the pole,

four holes in the middle and

one small hole at the bottom.

Warning Sticker.

Bottom Pole:

One slot at the top of the pole, two

holes near the top, two holes at

the bottom and a bent edge at the

bottom. Shortest pole.

GK GF

Large holes

Small

holes

(2)

(1)

1005748

HH01300

9/16” Wrenches

Tighten all Nuts

securely now.

Align the hole in the Top Pole with the slot in the Middle

Pole and slide the Top Pole over the Middle Pole.

Do not jam the poles together until instructed.

The Screw will spin freely once installed.

Insert a 1/4” x 3/4” Screw (PA) through the small

hole in the Top Pole and into the Middle Pole.

Note: There are two screw holes at the

bottom of the pole. The correct hole will

be slightly larger and slightly higher up

on the pole.

(1)

1005748

This step cannot be

reversed.

In order to seat the poles, strike each end of the pole

very hard 5 to 6 times on a piece of scrap wood or

cardboard. This must be done even if the poles cover

the slots before seating.

Measure from the top of the Top Pole to the bottom of the Middle

Pole. It must measure 83 1/2” or less. If it measures longer than

83 1/2”, strike it again on the wood. If it is still too long, do not

complete assembly. Call our Customer Service Department.

212.1 cm

83 1/2”

Align the hole in the Middle Pole with the slot in the Bottom Pole and slide the Middle Pole over the Bottom Pole.

Do not jam the poles together until instructed.

The Screw will spin freely once installed.

Insert the remaining 1/4” x 3/4” Screw (PA) through the small hole in the Middle

Pole and into the Bottom Pole.

WARNING

The poles must be seated together!!

Even if the poles cover the slots before

seating, you must strike them on the

wood ve to six times!! Failure to seat

the poles correctly could allow the poles

to separate during use, which could lead

to serious personal injuries or property

damage as listed on Page One.

If the Top and Middle Poles do not completely

cover the slots on the Middle and Bottom Poles

after seating, DO NOT COMPLETE ASSEMBLY. Call

our Customer Service Department.

Note: There are two screw holes at the

bottom of the pole. The correct hole will

be slightly larger and slightly higher up

on the pole.

Insert two self-tapping screws

(PB) into the back of the pole at

the locations shown.

(1)

Make sure the Rubber Gasket is

inside the Base Cap (AH).

Rubber Gasket

Screw the Base Cap (AH)

onto the Base.

7 8

The Bracket on the Middle

Pole faces the Base.

The attened end of the Pole Brace (AM) has a smaller

hole and attaches to the top hole in the Base (AF). The

angled end attaches to the pole.

Only nger

tighten now.

Repeat for the other

Pole Brace.

(2)

(4)

1006763

Completely tighten all Base

and Pole Brace hardware.

Tip the Base forward until the

pole rests on the ground.

(1)

9/16” Wrenches

1/2” Wrenches

7/16” Wrench

1/2” Wrenches

Completely tighten

the Nuts (HA).

(2)

The Tap Bolts (RE) should be at

the outer edge of the holes.

Tighten the T-Nuts (RA) only until the

Rubber Washers (RD) begin to bulge.

(2)

HD9125B

(2)

1012253

Place the Plastic Guard (AC) on

the back of the Rim.

Only hand tighten the Nuts (HH).

Tighten the 5/16” Jam Nuts (RK)

onto the U-Bolt as far as they

will go.

(2)

You may want to perform step #36

now, before proceeding with this step.

HD9125B

(2)

(1)

1012253

Only hand tighten

the Nuts (HH).

Tightening these Nuts later will adjust

the Rim tension.

The lower holes should go

over the Carriage Bolts.

Bend the Backboard Brackets (LB

& RB) out.

(Not actual size)

Do not overtighten

the Nuts (HH).

Completely tighten

all Rim hardware.

1/2” Wrenches

(2)

(1)

(2)

Tighten the Nut until it

is ush with the Bolt.

(1)

3/4” Wrenches

HD9125B

(3)

(2)

(3)

3/4” Wrenches

Attach this end of the Long Extension Arms (AL) to the

Backboard Brackets

Tighten the

Nut until it

is ush with

the Bolt.

HH01300

(1)

(Not actual size)

(1)

(Not actual size)

(2)

(4)

The Backboard and Rim should

be on the ground resting on

cardboard with the Extension

Arms facing up.

TWO PEOPLE REQUIRED FOR THIS STEP

The Backboard must be on the

opposite side as the Bracket on

the Middle Pole.

HH01300

(2)

25 26

Wipe off any grease that may be on the Channel (AN) before

attaching the Sticker.The bottom of the Height Sticker (AI)

lines up with the bottom edge of the Inner Channel (AN).

Squeeze the Trigger while

inserting the Inner Channel (AN).

Slide the Inner Channel (AN) up to the

10’ mark and release the Trigger so it

clicks into place.

Insert the slotted end rst.

Remove the Inner Channel (AN) that is

packaged inside the Outer Tube (AO)

before attaching the Handle (AR).

(1)

WARNING

Do not overtighten the Cap Nut. If the end of the Bolt

breaks through the plastic cap, call our Customer Service

Department at the number on Page One. Exposed threads

on the end of the Bolt may cause serious injuries such as

those listed on Page One.

1/2” Wrenches

(1)

(2)

HD9125B

3/4” Wrenches

TWO PEOPLE REQUIRED

FOR THIS STEP.

(1)

Use the holes closest to

the pole.

Tighten all Nuts

securely now.

9/16” Wrenches

Tighten all Nuts securely now.

Hook the Springs (AD) into the #3 holes in the Backboard Brackets.

Use the closed end of

a wrench to pull the

Springs up and over

the Bolt.

32 33

Attach the Net (AB).

Two adults are required to complete assembly. To

prevent serious injuries, the pole should be held down

by one adult at all times while lling the Base.

Filling the Base with Sand

With the Backboard extended to its highest position,

use a funnel and ll the Base with 375 lbs. of sand.

Filling the Base with Water

Check the Base Cap for leaks

frequently.

Carefully stand the system up.

Never put the system in an upright position without proper

weight in the Base. The system may fall over and could

result in serious personal injury or property damage.

WARNING

For safety reasons, we recommend

that sand be used instead of water

to ll the Base.

If a leak develops, water could run

out unnoticed, allowing the unit to

fall over and resulting in serious

personal injuries or property

damage. Check the Base carefully

for leaks.

Screw the Base Cap (AH) onto the Base.

With the Backboard extended to its highest position, ll the Base

with cold water and one tablespoon of chlorine bleach.

Warning Sticker (AV)

Lay the Pole Pad (AW) at on the ground. Apply

the extra Warning Sticker (AV) onto the Pole

Pad just below the logo at the top of the Pole

Pad. Eliminate any air bubbles in the Sticker.

Attach the Pole Pad (AW) to the pole. The bottom strap

should go below the Pole Braces.

Apply the two Logo Stickers to the Backboard

in the locations shown.

1. Make sure the surface beneath the Base is smooth and free of stones, gravel or other sharp

objects that could puncture the Base and cause leakage.

2. Check the Base frequently for cracks or punctures.

3. Always check the water level before play. If a leak is found or the water level is low, lay the

system down on the ground and call the Customer Service number for assistance.

4. If the unit is to be stored without weight, tilt the unit forward and rest the Rim on the

ground.

5. Each time the Base is lled with water, add one tablespoon of chlorine bleach to the water

to prevent algae formation inside the Base.

WHEN USING WATER IN THE BASE TAKE THE

FOLLOWING PRECAUTIONS:

Operation of the height adjustment system

WHILE TRANSPORTING THE SYSTEM, USE CAUTION TO

PREVENT THE MECHANISM FROM ADJUSTING.

The adjustable system may be adjusted from 7 1/2 feet to 10 feet in 6-inch increments.

Hold the Handle tightly and squeeze the Trigger. Raise the Handle to lower the Backboard,

or lower the Handle to raise the Backboard.

Moving the system

WARNING: The system must only be moved by people who are capable of

handling its weight. Children should not be allowed to move the system.

a. Adjust the system to its lowest position.

b. Stand in front of the system and pull on the pole until the unit is balanced on its Wheels.

c. Move the system to the desired location and carefully set the Base down.

The life of your basketball system depends on many variables. The climate,

exposure to corrosives such as salt, pesticides, or herbicides, and excessive use

or misuse can all contribute to pole failure, which may cause property damage

or personal injury.

Check your basketball system frequently for loose hardware, excessive wear, and

signs of corrosion. For safety reasons, and to prolong the life of your basketball

system, you must take the following preventive measures.

a. Check all Nuts and Bolts. If any are loose, tighten them.

b. Check all parts for excessive wear and tear. If necessary, replace any parts that

have been worn or damaged through usage. Check the Pole Cap for cracks

or tears that could let water into the pole. Contact our Customer Service

Department for replacement parts.

c. Inspect the Warning Sticker on the pole. If it is ripped, faded, or illegible, call

our Customer Service Department to request a replacement Sticker.

d. Check all pole sections for visible rust or chipped or cracked paint. If either are

present, do the following:

1. Use an emery cloth to completely remove any rust or chipped paint.

2. Clean the area with a damp cloth and allow it to dry.

3. Apply two coats of a rust preventative, high gloss enamel paint to the

area. Allow the paint to dry between coats.

IF RUST HAS PENETRATED THROUGH THE POLE ANYWHERE,

REPLACE IT IMMEDIATELY!

POLE CARE AND SYSTEM

MAINTENANCE

Only clean the Backboard with the approved

cleaning materials listed below:

Registered Trademark of the Drackett Products Company.

Registered Trademarks of Procter & Gamble.

Registered Trademark of Texize, Division of Norton Norwich Products Inc.

Registered Trademark of the Clorox Company.

Windex

Joy

Mr. Clean

Fantastik

Formula 409

The use of other chemicals will

void the warranty.

FAUTE DE NE PAS SUIVRE CES AVERTISSEMENTS, VOUS

RISQUEZ DE CAUSER DES BLESSURES GRAVES ET/OU

DES DOMMAGES À L’ÉQUIPEMENT.

SI NO SE OBEDECEN ESTAS ADVERTENCIAS PUEDEN

PRODUCIRSE GRAVES LESIONES y/O DAñOS A LA

PROPIEDAD.

Le propriétaire doit s’assurer que tous les joueurs connaissent

et appliquent les règles suivantes an d’utiliser l’équipement en

toute sécurité.

WARNING

El propietario del sistema debe asegurarse de que todos

los jugadores conozcan y respeten estas reglas para que el

sistema se use en forma segura.

FAILURE TO FOLLOW THESE WARNINGS MAy RESULT IN

SERIOUS INJURy AND/OR PROPERTy DAMAGE.

Owners must ensure that all players know and follow these

rules for safe operation of the system.

Only hang from the rim briey to regain balance or avoid injuring

others. Release the rim as soon as safely possible.

During play, especially when performing dunk type activities, keep

player’s face away from the backboard, rim, and net. Serious injury

could occur if teeth/face come in contact with the backboard, rim,

or net. Player should wear a mouth guard during play.

Do not slide, climb, or play on base or pole.

Completely ll base according to manufacturer’s instructions.

Never leave the unit standing in an upright position without rst

lling the base with weight or the system will tip quickly causing

serious personal injury.

When adjusting height or moving system, keep hands and ngers

away from moving parts.

Do not allow children to move or adjust system.

Do not wear jewelry (rings, watches, necklaces, etc.) during play.

Objects may entangle in net.

Keep organic material away from pole base. Grass, litter, etc. could

cause corrosion and/or deterioration.

• Cuélguese del aro sólo en forma breve, para recuperar el

equilibrio o evitar lesionar a otros jugadores. Suéltese del aro lo

más pronto que pueda hacerlo con seguridad.

• Durante el juego, especialmente al embocar violentamente

de alto, la cara de los jugadores debe mantenerse alejada del

tablero, el aro y la red. Pueden producirse lesiones graves si los

dientes o la cara entran en contacto con el tablero, el aro o la red.

Los jugadores deben usar un protector bucal durante el juego.

• No se deslice, no trepe ni juegue sobre la base o el poste.

• Llene la base completamente siguiendo las instrucciones del

fabricante. Nunca deje la unidad en posición de uso sin haber

llenado previamente la base con material de contrapeso, pues el

sistema podría tumbarse rápidamente y causar graves lesiones

personales.

• Mantenga las manos y los dedos alejados de las piezas movibles

cuando regule la altura o desplace el sistema.

• No deje que los niños regulen ni desplacen el sistema.

• No use joyas (anillos, relojes, collares o gargantillas, etc.)

durante el juego. Estos objetos pueden engancharse en la red.

• La supercie donde se coloque la base debe estar lisa y

desprovista de piedras, grava u otros objetos. Las perforaciones

pueden originar pérdidas, y éstas pueden hacer que el sistema

se tumbe.

• No permita que la base del poste entre en contacto con

materiales orgánicos. El pasto, los desechos animales, etc.,

pueden causar corrosión y/o deterioros.

• Controle el poste y todas las piezas metálicas una vez al mes

en busca de signos visibles de corrosión (oxidación, picaduras,

escamado). Elimine todo rastro de óxido y vuelva a pintar con

esmalte para exteriores. Si el óxido ha penetrado cualquier pieza

de acero, reemplace esa pieza de inmediato.

• Inspeccione el sistema antes de cada uso para vericar que

esté adecuadamente contrapesado, que los elementos de jación

no estén ojos, que no haya desgaste excesivo, inestabilidad

ni signos de corrosión. Si encuentra irregularidades, repárelas

antes de usar el sistema.

Nunca juegue con un equipo dañado.

• No use el sistema en presencia de vientos fuertes o condiciones

climáticas adversas, ya que puede tumbarse. Coloque la unidad

en su posición de almacenamiento y/o en una zona a resguardo

del viento, lejos de propiedades personales que puedan dañarse

si el sistema se cae, y de líneas de suministro de energía.

• No use el sistema para levantar ningún objeto. El mecanismo

está diseñado para elevar solamente el peso del tablero con el

aro. No cuelgue nada de la agarradera, el aro, el tablero ni los

brazos de elevación, ya que esto puede dañar el sistema y anular

la garantía.

• Ne vous suspendez pas à l’anneau plus que nécessaire pour

retrouver votre équilibre ou éviter de blesser les autres joueurs.

Relâchez l’anneau aussitôt que possible.

• Lors d’un match, particulièrement dans le cas des smashs, le

visage du joueur ne doit pas faire face au panneau, à l’anneau,

ni au let. Le joueur risque de graves blessures si ses dents ou

son visage entrent en contact avec le panneau, l’anneau, ou le

let. Les joueurs doivent toujours porter un protège-dents lorsqu’ils

jouent.

• Ne glissez pas, ne grimpez pas, et ne jouez pas sur la base ou

le poteau.

• Remplissez complètement la base selon les instructions du

fabricant. Ne laissez jamais l’unité debout de plein pied sans avoir

d’abord rempli la base avec un poids ou l’équipement pourrait

basculer rapidement et causer de graves blessures.

• Lorsque vous ajustez la hauteur ou lorsque vous déplacez

l’équipement, gardez vos mains et doigts loin des pièces mobiles.

• Ne permettez pas aux enfants de déplacer ou d’ajuster

l’équipement.

• Ne portez pas de bijoux (bagues, montres, colliers, etc.) lorsque

vous jouez. Ces objets pourraient s’accrocher au let.

• La surface sur laquelle est posée la base doit être lisse et sans

gravier ou tout autre objet qui pourrait trouer la base entraînant

ainsi une fuite ce qui pourrait faire basculer l’équipement.

• La base ne doit pas non plus être posée sur aucun type de

matière organique. L’herbe, les déchets, etc. peuvent entraîner la

corrosion et la détérioration de l’équipement.

• Une fois par mois, vériez que le Poteau et toutes les pièces

en métal ne montrent pas de signes de corrosion (rouille, piqûres,

écaillage). Enlevez toute la rouille et repeignez complètement

avec une peinture pour extérieur. Si la rouille a pénétré une des

pièces en acier, vous devrez remplacer immédiatement la pièce

en question.

• A chaque fois que vous allez utiliser l’équipement, vériez d’abord

l’équilibre, la possibilité de pièces desserrées ou usées, la stabilité

de l’équipement et tout signe de corrosion ou réparation nécessaire

avant utilisation.

• Ne jouez jamais avec un équipement endommagé.

• N’utilisez pas l’équipement lors de fortes rafales de vent ou

de mauvais temps. L’équipement pourrait basculer. Placez

l’équipement dans un endroit abrité du vent ou loin des structures

qu’il pourrait endommager s’il basculait et loin des ls électriques.

• N’utilisez pas l’équipement pour lever ou soulever quoique ce

soit. Son mécanisme a été conçu uniquement pour soutenir le

poids du panneau et de l’anneau. N’accrochez rien au manche,

à l’anneau, au panneau ni aux leviers sous peine d’endommager

l’équipement et d’annuler la garantie.

ADVERTENCIA

AVERTISSEMENT

#FS16400

10/12/2004

www.lifetime.com

Surface beneath the base must be smooth and free of gravel or

other objects. Punctures cause leakage and could cause system

to tip over.

Once a month check pole and all metal parts for signs of corrosion

(rust, pitting, chipping). Completely remove rust and repaint with

exterior enamel. If rust has penetrated any steel part, replace that

part immediately.

Check system before each use for proper ballast, loose hardware,

excessive wear, instability, and signs of corrosion and repair

before use.

Never play on damaged equipment.

Do not use system during windy or severe weather. System may

tip over. Place system in an area protected from the wind or in an

area away from property that may be damaged if the system falls,

and from overhead power lines.

 Do not use the system to lift or hoist anything. The mechanism is

designed to lift only the weight of the backboard and rim. Do not

hang anything from the handle, rim backboard, or lifter arms as

this will damage the system and void the warranty.

Reebok 51549 Manuel utilisateur

Marque: Reebok

Modèle: 51549

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Reebok 51549 User manual

Reebok 51549 Manuel utilisateur

Reebok 51549 Manuel utilisateur

dans d''autres langues

Autres documents