Lifetime 90469 Le manuel du propriétaire

Lifetime’s assembly experts offer quick responses and great customer service.

PUMP ADJUST

®

BASKETBALL SYSTEM

Call: 1-800-225-3865

7:00 am–5:00 pm (Monday–Friday) MST

and 9:00 am–1:00 pm Saturday MST

Web: www.lifetime.com/instructions

Live Chat: www.lifetime.com/instructions

NEED HELP? TALK TO US!

MODEL# AND PRODUCT ID (you will need both when contacting us)

Model Number: Product ID:

Lifetime

®

basketball systems are designed to be

strong and durable. We strive to make assembly as

easy as possible without compromising quality. If

you get stuck, we have tools to help:

• Prepare the Area

Before you start, make sure you have the required

amount of concrete and rebar (not included).

• Recruit Friends and Family

Assembly should take 3 people about 2–3

hours to complete, plus 3 days for the concrete to

cure.

TOOLS REQUIRED TABLE OF CONTENTS

90469

(x2) (x2) (x2) (x2) (x2)

(x1)

1/2" (13 mm) 9/16" (14 mm) 11/16" (18 mm) 3/4" (19 mm) 1/2" (13 mm)

Icon Legend................................2

Notices....................................3

Ground Preparation.....................4

Pole Assembly.............................8

Backboard to Rim Assembly......11

Backboard to Pole Assembly.......15

Parts Identiﬁ er..........................i-iv

Handle Assembly......................22

Final Assembly..........................31

Maintenance Instructions..........36

Warning Sticker........................37

Registration........................38

Warranty................................39

(x1)

30” Rebar

Cement Mix

Level

(x1)

1/2" (13 mm)

(x1)

(x3)

(x1)

Frame pads and Backboard

Graphics may vary from the

system pictured here.

COPY

2

• Indicates the parts to be used for a section.

• Indicates special heed should be taken when reading.

• Indicates the hardware to be used for a section.

• Indicates the tools to be used for a section.

• Indicates no hardware required for a speciﬁ c page.

• Indicates no parts required for a speciﬁ c section.

• Indicates to use/not to use an electric drill for a speciﬁ c step.

ICON LEGEND

• Indicates the use of a Centerlock Nut. A Nut with this marking will require some effort to tighten. This

hardware was designed with this feature in order to prevent loosening later.

• Save this instruction in the event that the manufacturer has to be contacted for replacement parts.

CONTACT US

www.lifetime.com/instructions

Call: 1-800-225-3865

7:00 am–5:00 pm (Monday–Friday) MST

and 9:00 am–1:00 pm Saturday MST

1176317_B

7/22/2016

COPY

3

WARNINGS & NOTICES

Most injuries are caused by misuse and/or not following instructions. Use caution when using this product.

To ensure safety, do not attempt to assemble this product without following the instructions carefully. Check entire box and inside all packing

material for parts and/or additional instruction material. Before beginning assembly, read the instructions and identify parts using the hardware

identiﬁ er and parts list in this document. Proper and complete assembly, use and supervision are essential for proper operatation and to reduce the

risk of accident or injury. A high probability of serious injury exists if this product is not installed, maintained, and operated properly.

FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE AND WILL VOID WARRANTY.

Owner must ensure that all players know and follow these rules for safe operation of the system.

• If using a ladder during assembly, use extreme caution.

• Three capable adults are recommended for this operation.

• Check base daily for leakage. Leaks will cause system to fall.

• Assemble the pole sections properly. Failure to do so could cause the pole sections to separate during play or transport.

• Minimum operational height is 6 ft 6 in (1.98m) to the bottom of the backboard.

SAFETY INSTRUCTIONS

4

1

GROUND PREPARATION

Metal Parts

Hardware Bag

TOOLS REQUIRED

PARTS REQUIRED

HARDWARE REQUIRED

(x1)

ALE (x1)

30" Rebar

Cement Mix

Level

BGW (x1)

Paper Parts

(x1)

5

TOOLS AND HARDWARE REQUIRED

X SECTION 1 (CONTINUED)

1.1

• A Ground Sleeve is available as an alternative

to cementing the Pole into the ground. Please

contact Customer Service for more information.

!

• Dig a round hole 24" deep and 21" in diameter. If

you live in an area where frost heaves may pose a

problem, consult your local building inspector to

determine the proper hole depth. The edge of the

hole should be ﬂ ush with the edge of the playing

surface.

(9 Bags, 80 lb each)

ALE

16"

ALE

BGW

(x1)

1.2

• Make a mark 16 inches from the dimpled

end of the Bottom Pole (ALE) (do not scratch

the powder coating). Slide the Alignment

Frame (BGW) over the Bottom Pole.

1.3

• Mix 8 1/2 bags of concrete. Save 1/2 bag of

concrete mix to use later in the assembly. Pour

the mixed concrete into the hole until it is ﬁ lled

to the level of the playing surface.

6

TOOLS AND HARDWARE REQUIRED

X SECTION 1 (CONTINUED)

• Slide the dimpled end of the Bottom Pole (ALE) into the cement up to the 16-inch mark. Position the pole next

to the playing surface. For regulation courts, the Alignment Frame (BGW) should cross the playing surface at the

middle of the scored measurements.

1.4

• Use a Level to make sure the Bottom Pole is standing vertical. Form

the cement into a downward slope away from the pole to allow water

runoff. Failure to do so may result in premature rusting of the Pole.

• If the pole is buried too deep or too shallow,

the rim will not to be at the correct height.

• Do not continue the assembly

until the concrete has been

allowed to set for 1-4 hours.

!

30" Rebar

Playing

Surface

ALE

TOP VIEW

BGW

ALE

Rebar

• Insert the 30" rebar (not included) inside the Bottom Pole (ALE) so it is about 15" from the top of the pole. Check

the pole several times within the ﬁ rst hour to make sure that all sides are vertical and that the 16-inch mark remains level with

the surface.

1.5

7

TOOLS AND HARDWARE REQUIRED

X SECTION 1 (CONTINUED)

• Mix the remaining 1/2 bag of concrete. Fill the Bottom Pole (ALE) with concrete until it reaches the top of the

rebar (about 15" from the top of the pole). Tamp the concrete down in the Bottom Pole with a broom handle

to remove air pockets. Clean all concrete off the outside of the pole. You may now remove the Alignment Frame

(BGW).

1.6

15"

• Stop assembly now. Do not continue the assembly until the concrete has been allowed

to set for at least 72 hours (3 days). In humid climates or wet weather, allow more time

for the concrete to cure. Do not proceed until the curing process is complete.

!

8

POLE ASSEMBLY

2

BCO

Metal Parts

Hardware Bag

TOOLS REQUIRED

PARTS REQUIRED

HARDWARE REQUIRED

(x1)

9/16" (14 mm)

(x1)

(x2)

• Warning Sticker applied to this Pole

CMV (x2)*

AAA (x2)

AAF (x2)

ANF (x2)

ANE (x2)

5”

• Only one Self-Drilling Screw (CMV) will

be used in Section 2. Save the second

Screw for use in Section 5.

ALH (x1)

ALF (x1)

ALL (x1)

!

9

TOOLS AND HARDWARE REQUIRED

X SECTION 2 (CONTINUED)

• Secure the Pole Bracket (ALL) to Top Pole (ALH)

with the hardware shown.

2.1

ANE (x2)

ANF (x2)

ALH

ANF

ANE

ALL

ABB

AAF

Large Holes

Small Holes

ABB (x2)

9/16" (14 mm)

(x2)

5”

AAF (x2)

ALH

ALF

FAUTE DE NE PAS SUIVRE CES AVERTISSEMENTS,

VOUS RISQUEZ DE CAUSER DES BLESSURES

GRAVES ET/OU DES DOMMAGES À L’ÉQUIPEMENT.

SI NO SE OBEDECEN ESTAS ADVERTENCIAS

PUEDEN PRODUCIRSE GRAVES LESIONES Y/O

DAÑOS A LA PROPIEDAD.

Le propriétaire doit s’assurer que tous les joueurs

FRQQDLVVHQWHWDSSOLTXHQWOHVUqJOHVVXLYDQWHVD¿Q

d’utiliser l’équipement en toute sécurité.

WARNING

El propietario del sistema debe asegurarse de que

todos los jugadores conozcan y respeten estas reglas

para que el sistema se use en forma segura.

FAILURE TO FOLLOW THESE WARNINGS MAY

RESULT IN SERIOUS INJURY AND/OR PROPERTY

DAMAGE.

Owners must ensure that all players know and follow

these rules for safe operation of the system.

• Cuélguese del aro sólo en forma breve, para recuperar el

equilibrio o evitar lesionar a otros jugadores. Suéltese del

aro lo más pronto que pueda hacerlo con seguridad.

• Durante el juego, especialmente al embocar violentamente

de alto, la cara de los jugadores debe mantenerse alejada

del tablero, el aro y la red. Pueden producirse lesiones

graves si los dientes o la cara entran en contacto con

el tablero, el aro o la red. Los jugadores deben usar un

protector bucal durante el juego.

• No se deslice, no trepe ni juegue sobre el poste.

• Mantenga las manos y los dedos alejados de las piezas

movibles cuando regule la altura del sistema.

• No deje que los niños regulen el sistema.

• No use joyas (anillos, relojes, collares o gargantillas, etc.)

durante el juego. Estos objetos pueden engancharse en la

red.

• No permita que la base del poste entre en contacto con

materiales orgánicos. El pasto, los desechos animales, etc.,

pueden causar corrosión y/o deterioros.

• Controle el poste y todas las piezas metálicas una vez al

mes en busca de signos visibles de corrosión (oxidación,

picaduras, escamado). Elimine todo rastro de óxido y

vuelva a pintar con esmalte para exteriores. Si el óxido ha

penetrado cualquier pieza de acero, reemplace esa pieza

de inmediato.

,QVSHFFLRQH HO VLVWHPDDQWHV GHFDGD XVRSDUDYHUL¿FDU

TXHORVHOHPHQWRV GH¿MDFLyQQRHVWpQ ÀRMRVTXHQRKD\D

desgaste excesivo, inestabilidad ni signos de corrosión.

Si encuentra irregularidades, repárelas antes de usar el

sistema.

• Nunca juegue con un equipo dañado.

• No use el sistema para levantar ningún objeto. El

mecanismo está diseñado para elevar solamente el peso

del tablero con el aro. No cuelgue nada de la agarradera, el

aro, el tablero ni los brazos de elevación, ya que esto puede

dañar el sistema y anular la garantía.

•Ne vous suspendez pas à l’anneau plus que nécessaire

pour retrouver votre équilibre ou éviter de blesser les autres

joueurs. Relâchez l’anneau aussitôt que possible.

• Lors d’un match, particulièrement dans le cas des smashs,

le visage du joueur ne doit pas faire face au panneau, à

O¶DQQHDXQLDX¿OHW/HMRXHXUULVTXHGHJUDYHVEOHVVXUHVVL

ses dents ou son visage entrent en contact avec le panneau,

O¶DQQHDXRX OH¿OHW /HVMRXHXUV GRLYHQWWRXMRXUVSRUWHUXQ

protège-dents lorsqu’ils jouent.

• Ne glissez pas, ne grimpez pas, et ne jouez pas sur la base

ou le poteau.

• Lorsque vous ajustez la hauteur ou l’équipement, gardez

vos mains et doigts loin des pièces mobiles.

• N’autorisez pas les enfants à ajuster l’équipement.

• Ne portez pas de bijoux (bagues, montres, colliers, etc.)

lorsque vous jouez. Ces objets pourraient s’accrocher au

¿OHW

• Gardez la base du poteau libre de toute matière organique.

L’herbe, les déchets, etc. peuvent la corroder et la

détériorer.

8QHIRLVSDUPRLVYpUL¿H]TXHOHSRWHDXHWWRXWHVOHVSLqFHV

en métal ne montrent pas de signes de corrosion (rouille,

piqûres, écaillage). Enlevez toute la rouille et repeignez

complètement avec une peinture pour extérieur. Si la rouille

a pénétré une des pièces en acier, vous devrez remplacer

immédiatement la pièce en question.

$FKDTXHIRLVTXHYRXVDOOH]XWLOLVHU O¶pTXLSHPHQWYpUL¿H]

d’abord l’équilibre, la possibilité de pièces desserrées ou

usées, la stabilité de l’équipement et tout signe de corrosion

ou réparation nécessaire avant utilisation.

• Ne jouez jamais avec un équipement endommagé.

• N’utilisez pas l’équipement pour lever ou soulever quoique

ce soit. Son mécanisme a été conçu uniquement pour

soutenir le poids du panneau et de l’anneau. N’accrochez

rien au manche, à l’anneau, au panneau ni aux leviers sous

peine d’endommager l’équipement et d’annuler la garantie.

ADVERTENCIA

AVERTISSEMENT

y2QO\ KDQJ IURPWKH ULP EULHÀ\ WR UHJDLQ EDODQFHRU DYRLG

injuring others. Release the rim as soon as safely possible.

yDuring play, especially when performing dunk type activities,

keep player’s face away from the backboard, rim, and net.

Serious injury could occur if teeth/face come in contact with

the backboard, rim, or net. Player should wear a mouth

guard during play.

yDo not slide, climb, or play on pole.

yWhen adjusting height or moving system, keep hands and

¿QJHUVDZD\IURPPRYLQJSDUWV

yDo not allow children to move or adjust system.

yDo not wear jewelry (rings, watches, necklaces, etc.) during

play. Objects may entangle in net.

yKeep organic material away from pole base. Grass, litter,

etc. could cause corrosion and/or deterioration.

yOnce a month check pole and all metal parts for signs of

corrosion (rust, pitting, chipping). Completely remove rust

and repaint with exterior enamel. If rust has penetrated any

steel part, replace that part immediately.

y Check system before each use for loose hardware,

excessive wear, instability, and signs of corrosion and repair

before use.

y ever play on damaged equipment.

y Do not use the system to lift or hoist anything. The

mechanism is designed to lift only the weight of the

backboard and rim. Do not hang anything from the handle,

rim backboard, or lifter arms as this will damage the system

and void the warranty.

#FS16500

10/12/2004

www.lifetime.com

• Align the hole in the Top Pole (ALH) with the slot in

the Middle Pole (ALF) and slide the Top Pole over the

Middle Pole.

2.2

10

TOOLS AND HARDWARE REQUIRED

X SECTION 2 (CONTINUED)

2.3

• Do not hit your feet with the

Pole sections, as serious injury

could occur.

(x1)

• THIS STEP CANNOT BE REVERSED! Strike the end of the Pole Assembly on a piece of scrap wood or cardboard

ﬁ ve to six times.

6x

!

(x1)

CMV (x1)

CMV

ALH

ALF

1" up from bottom of

Top Pole

• After the Poles have been seated, measure up 1" from the bottom center of the Top Pole (ALH) and insert one

Self-Tapping Screw (CMV) into the Pole as shown.

2.4

WARNING

The Poles must be seated together! Even if the Poles cover

the slots before seating, they must be struck on a hard

surface ﬁve to six times! Failure to seat the Poles correctly

could allow the Poles to separate during use, which could

lead to serious personal injuries or property damage.

11

BACKBOARD TO RIM ASSEMBLY

3

BCS

Metal Parts

Hardware Bag

PARTS REQUIRED

HARDWARE REQUIRED

TOOLS REQUIRED

(2)

1/2” (13 mm)

AAQ (x2)

EAP

(x2)

ABK (x4)

AAV (x2)

ADR (x4)

ABQ (x1)

APY (x1)

Hardware shown at 50% of Actual Size

ALX (x1)

AJI (x1)

1/2” (13 mm)

(1) (1)

ALD (x1)

AMA (x1)

Plastic Parts

BGR (x1)

APZ (x1)

Hardware shown at 25% of Actual Size

AJW (x2)

AOW (x1)

12

X SECTION 3 (CONTINUED)

TOOLS AND HARDWARE REQUIRED

3.1

• Insert two Carriage Bolts (EAP) through the Rim Pivot Bracket (APY) as shown.

3.2

EAP

APY

ABQ (x1)

(Not to scale)

• Use the 1/2” socket head from the socket head wrench to press one Push Nut (AAQ) onto one end of the Axle

(ABQ).

AAQ

ABQ

• The Push Nut should rest about 1/4” from the end of the

Axle. If the Push Nut slips on too far, continue sliding it to

the other end of the Axle to remove it and try again.

!

AAQ (x2)

EAP (x2)

(1)

1/2” (13 mm)

3.3

• Slide the end of the Axle (ABQ) through the Rim (ALX) and the Rim Pivot Bracket (APY). Press the Push Nut (AAQ) onto

the end of the Axle. Use the 1/2” socket head to secure the Push Nut if needed.

APY

ALX

ABQ

AAQ

13

TOOLS AND HARDWARE REQUIRED

X SECTION 3 (CONTINUED)

3.4

• Insert the U-Bolt (APZ) through the upper part of the opening on the backside of the Backboard (AJI). Connect the Rim

(ALX) and Plastic Guard (ALD) to the Backboard (AJI) with the hardware as shown.

ABK

APZ

BGR

AJI

EAP

ALX

ALD

ABK (x2)

BGR (x1)

APZ (x1)

(2)

1/2” (13 mm)

ABK

EAP

14

X SECTION 3 (CONTINUED)

TOOLS AND HARDWARE REQUIRED

3.5

• Thread two Jam Nuts (AAV) all the way on to the U-Bolt (APZ). Then slide the Compression Springs (AJW) onto the U-Bolt

and place the Spring Retainer Plate (AOW) over the Compression Springs. Tighten the Nylock Flange Nuts (ABK) until the

Rim (ALX) does not wobble to complete this step.

ABK (x2)

AAV (x2)

AJW (x2)

ABK

AOW

AJW

APZ

AAV

• DO NOT COMPLETELY TIGHTEN THE NYLOCK FLANGE NUTS IN

THIS STEP! Only tighten the nuts until the Rim does not wobble.

Tightening the Nuts will adjust the Rim tension.

!

3.6

• Attach the Rim Cover Plate (AMA) to the Rim with the hardware shown.

ADR (x4)

ADR

AMA

ADR

(2)

1/2” (13 mm)

15

Metal Part

Hardware Bag

TOOLS REQUIRED

PARTS REQUIRED

HARDWARE REQUIRED

BACKBOARD TO POLE ASSEMBLY

4

(1) (2)

(1) (1)

1/2” (13 mm)

3/4” (19 mm)

11/16” (18 mm)

(1)

BCR

AAD (x1)

ANQ (x2) AQD (x1)

ANU (x2) AQB (x2)

ANS (x4)

*

AAX (x4)

7 1/16”

5”

ANP (x1)

AOR (x6)

ABP (x2)

ANK (x4)

AQC (x2)

BGP (x2)

BGO (x2)

BLC (x1)

ANZ (x2)

ABN (x4)

*Hardware Bag BCR

may include extra Plastic

Plugs (ANS).

16

X SECTION 4 (CONTINUED)

TOOLS AND HARDWARE REQUIRED

4.1

• Insert one end of the Tie Plate (BLC) into the slot on the Lower Extension Arm (BGP), then iInsert the opposite end of the

Tie Plate (BLC) into the slot on the other Lower Extension Arm (BGP) as shown.

• Do not overtighten the Cap Nut. If the end of the Bolt breaks

through the plastic cap, call our Customer Service Department.

Exposed threads on the end of the Bolt may cause serious injuries.

!

1/2” (13mm)

(x1)

1/2” (13 mm)

(x1)

BLC

BGP

AQB

AAN

BGP

BLC

AQB (x2)

AAN (x2)

4.2

• Secure the Lower Extension Arms (BGP) together with the hardware shown. Use a 1/2” Socket Wrench to screw the Thread-

Cutting Bolts (AQB) through the Lower Extension Arms and the Tie Plate (BLC).

17

TOOLS AND HARDWARE REQUIRED

X SECTION 4 (CONTINUED)

4.3

TOOLS AND HARDWARE REQUIRED / HERRAMIENTAS Y ACCESORIOS REQUERIDOS / OUTILS ET ACCESSOIRES REQUIS

• Insert the Extension Arm Caps (AQC) into the ends of the Lower Extension Arms (BGP) as shown.

X SECTION 4 (CONTINUED)

• Place the Top Pole (ALH) to the Lower Extension Arms (BGP) and secure them with the hardware shown.

4.4

BGP

AQC

BGP

AAX

AAD

AOR

ANZ

ANZ ANZ

ANZ

ALH

• Tighten the Nut until it is ﬂ ush

with the end of the Bolt.

!

AAX (x1)

AAD (x1)

7 1/16”

3/4”(19 mm)

(x2)

ANZ (x2)

AOR (x2)

18

X SECTION 4 (CONTINUED)

TOOLS AND HARDWARE REQUIRED

AAX (x1)

4.5

• Attach the Upper Extension Arms (BGO) to the Top Pole (ALH) with the hardware as shown.

3/4” (19 mm)

(x2)

5”

BGO

AQD

AAX

ANK

ABN

ANK

AQD (x1)

ANK (x2)

• Tighten the Nut until it is ﬂ ush

with the end of the Bolt.

!

ABN (x2)

19

TOOLS AND HARDWARE REQUIRED

X SECTION 4 (CONTINUED)

4.6

ANP (x1)

ABP (x2)

AOR (x2)

ANQ (x2)

BGP BGP

AJI

ANQ

AOR

ANP

ABP

AOR

ANQ ANQ

ANP

3/4” (19 mm)

(x2)

11/16” (18 mm)

(x1)

• Rest the Rim on cardboard to prevent scratching, then secure the Lower Extension Arms (BGP) to the Backboard (AJI)

with the hardware shown. Screw the Nut Coupler (ANP) onto one of the Hex Bolts (ANQ), then onto the other. Center the

Coupler between the two Bolts as shown.

• Make sure the 1/2” x 3/8” Poly Spacers (ABP) positioned between the Lower

Extension Arms and the Backboard do not bulge.

!

20

X SECTION 4 (CONTINUED)

TOOLS AND HARDWARE REQUIRED

4.7

AOR (x2)

ANK (x2)

ANU (x2)

AAX (x2)

• Attach the Upper Extension Arms (BGO) to the Backboard (AJI) with the hardware as shown.

3/4” (19 mm)

(x2)

ABN (x2)

AAX

AOR

ANK

ANU

BGO

ABN

• Tighten the Nuts until they are

ﬂ ush with the end of the Bolts.

!

La page charge ...

Lifetime 90469 Le manuel du propriétaire

Lifetime 90469 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents