Mafell KSS 40 18M bl Mode d'emploi

KSS40 18 M bl

170692.0922/b

IMPORTANT

Read Before Using

IMPORTANT

Lire avant usage

IMPORTANTE

Leer antes de usar

Operating/Safety Instructions

Consignes d’utilisation/de sécurité

Instrucciones de funcionamiento y seguridad

For English Version

See page 2

Version française

Voir page 35

Versión en español

Ver la página 68

KSS40 18 M bl

2

09/2022

English

Table of contents

1 Signs and symbols ........................................................................................................... 4

1.1 Identification of the device ................................................................................................ 6

2 Product specifications ...................................................................................................... 6

2.1 Technical data .................................................................................................................. 7

2.2 Scope of delivery .............................................................................................................. 7

2.3 Adjustment elements ........................................................................................................ 8

3 General safety .................................................................................................................. 9

3.1 Intended use ..................................................................................................................... 9

3.2 Foreseeable misuse ......................................................................................................... 9

3.3 Safety instructions .......................................................................................................... 10

3.4 Specific safety rules ....................................................................................................... 11

3.5 Safety devices ................................................................................................................ 15

3.6 Residual risks ................................................................................................................. 16

4 Setup / adjustment ......................................................................................................... 16

4.1 Charging the rechargeable battery ................................................................................. 16

4.2 Inserting the rechargeable battery .................................................................................. 17

4.3 Removing the rechargeable battery ............................................................................... 17

4.4 Chip extraction ............................................................................................................... 18

4.5 Saw blade selection ....................................................................................................... 18

4.6 Changing the saw blade ................................................................................................. 19

4.7 Riving knife ..................................................................................................................... 21

5 Operation ........................................................................................................................ 22

5.1 Startup ............................................................................................................................ 22

5.2 Switching on ................................................................................................................... 22

5.3 Switching off ................................................................................................................... 22

5.4 Cutting depth setting ...................................................................................................... 23

5.5 Setting for bevel cuts ...................................................................................................... 23

5.6 Plunge cuts ..................................................................................................................... 24

5.7 Shadow gap cuts ............................................................................................................ 25

5.8 Sawing with the Flexi bar ............................................................................................... 26

5.9 Sawing along markings .................................................................................................. 28

5.10 Sawing with the parallel guide fence .............................................................................. 28

5.11 Working with the guiding device ..................................................................................... 29

5.12 Setting for Miter cuts ...................................................................................................... 30

6 Service and maintenance ............................................................................................... 31

6.1 Storage ........................................................................................................................... 31

6.2 Transport ........................................................................................................................ 31

6.3 Disposal of a rechargeable battery ................................................................................. 32

7 Troubleshooting .............................................................................................................. 32

KSS40 18 M bl

09/2022

3

8 Optional accessories ...................................................................................................... 34

9 Exploded view and spare parts list ................................................................................. 34

KSS40 18 M bl

4

09/2022

1 Signs and symbols

These operating instructions contain the following general information signs to guide you, the reader, through

the operating instructions and to provide you with important information.

Sign

Meaning

Important information

This sign highlights user tips and other useful information.

➢

Identifies an intermediate result in a sequence of actions.

✓

Identifies the final result of a sequence of actions.

Tab. 1: General signs and their meanings

Warning icons warn of dangerous points, risks and obstacles.

Icon

Meaning

Warning

This sign can be found at all locations where you can find information regarding your

safety. Non-observance can result in extremely serious injuries.

Warns of danger of electric shock.

Warns of danger caused by dust.

Warns of the danger of cutting.

Warns of the danger of cutting off or severing limbs.

Warns of the danger of fire and explosion.

Tab. 2: Warning icons and their meanings

KSS40 18 M bl

09/2022

5

Mandatory icons are intended to prevent accidents.

Icon

Meaning

Wear eye protection.

Wear dust mask.

Wear hearing protection.

Wear protective gloves.

Tab. 3: Mandatory icons and their meanings

During the operation of the power tool there are always actions to be taken where hazards can occur. These

potentially dangerous actions are preceded by warnings which must be observed.

Classification of the danger level (signal words) of warnings

Warning

Meaning and consequences of non-observance

Imminent danger that will cause serious or fatal injuries.

Potentially dangerous situation that can cause serious or

fatal injuries.

Potentially dangerous situation that can cause minor

injuries.

Tab. 4: Structure of warnings

KSS40 18 M bl

6

09/2022

1.1 Identification of the device

The icons listed and explained below can be found on the rating plate or on the product.

Symbol

Explanation

Symbol

Explanation

V

Volt

1, 2, 3, ...

I, II, III, ...

Rotational speed setting

A

Ampere

rpm

Revolutions per minute

Hz

Hertz

ø

Saw blade diameter

W

Watt

~

Alternating current

kg

Kilogram (weight)

Protection class II

min

Minutes (time)

Read operating instructions

s

Seconds (time)

Protective goggles

n0

Rated speed at no load

Hearing protection

n

Rated speed at normal load

Dust mask

Cordless Allicance System (=CAS) is a cross-manufacturer battery pack

system. Further information is available at www.cordless-alliance-system.com

2 Product specifications

for machines with item number 91B323

The article number and machine number are listed on the type plate of the machine.

By entering the article number and machine number on the MAFELL homepage, you can

call up the spare parts lists, exploded drawings, and other product information belonging

to your machine (see also Chapter 9 Exploded view and spare parts list).

KSS40 18 M bl

09/2022

7

2.1 Technical data

Rated voltage

18 V, DC

Saw blade speed at no load

6700 rpm

Cutting depth 0°/30°/45°

42/36/29 mm [1.65/1.42/1.14 in]

Saw unit swivel range

0° to 45°

Saw blade diameter max/min

122/112 mm [4.80/4.41 in]

Saw blade body thickness

1.2 mm [0.05 in]

Tool cutting width

1.8 mm [0.07 in]

Saw blade mounting hole

20 mm [0.8 in]

Hose connector diameter

28 mm [1.1 in]

Weight with rechargeable battery and guiding

device

3.6 kg [7.94 lbs]

Dimensions (width x length x height)

200 x 580 x 200 [7.87 x 22.83 x 7.87 in]

2.2 Scope of delivery

Fig. 1: Scope of delivery

Components

A

Hand-held circular saw

B

Allen key in a holder on the machine

C

Parallel guide fence

D

Transport box

E

Shavings bag

F

2x rechargeable battery 18M 99 LiHD

G

Charger APS M

H

Flexi bar

I

Guiding device S

Additionally included:

1 hose connector

KSS40 18 M bl

8

09/2022

2.3 Adjustment elements

Fig. 2: Front and read adjustment elements

Adjustment elements on the machine

1

Plunge lever

2

Cutting depth scale

3

Pre-feed lever

4

Switch-on lock

5

Wing screws

6

Operating lever

7

Clamping lever

8

Tilting segment scale

9

Tilting segment wing screw

10

Lever of the rechargeable battery lock

11

Locking pin

KSS40 18 M bl

09/2022

9

3 General safety

Please read all safety instructions and directions. Failure to comply with the safety instructions and

directions can cause electric shock, fire and/or serious injuries. Please retain all safety instructions and

directions for future reference.

3.1 Intended use

The hand-held circular saw is only suitable for ripping and cross cutting of solid wood.

Panel material such as chip board, core board and medium density fiber board can also be processed.

Processing wood fiber insulation materials is also possible.

Use only saw blades that are approved by the manufacturer.

Use only the battery packs and the charger approved by the manufacturer.

3.2 Foreseeable misuse

The machine is not intended for any other use than the intended use listed above.

The manufacturer is not liable for any damage resulting from such other use.

To use the machine as intended, comply with the operating, maintenance and repair conditions specified by

MAFELL.

Foreseeable misuse also includes:

- Tampering with, removing and/or bypassing safety devices of any kind.

- Operating the machine without safety devices.

- Non-observance of safety and warning instructions in the operating instructions.

- Removing the safety and warning labels from the machine.

- Operating the machine by unauthorized persons.

- Failure to follow prescribed maintenance and care instructions.

Never use:

- Cracked and/or deformed saw blades.

- Saw blades made of high speed steel (HSS saw blades).

- Blunt saw blades as they impose an excessive load on the motor.

- Saw blades with a base body thicker than or a cutting width smaller than the riving knife.

- Saw blades that are not suitable for the no load speed of the saw blade.

- Abrasive wheels.

KSS40 18 M bl

10

09/2022

3.3 Safety instructions

READ ALL INSTRUCTIONS!

Non-observance of the instructions listed below can cause electric shock, fire and/or serious injuries.

Work area

- Children and adolescents are not allowed to operate this machine.

- Protect the machine and the rechargeable batteries from moisture.

- Do not throw the rechargeable batteries into a fire.

- Never use defective or deformed rechargeable batteries.

- Never try to open the rechargeable batteries.

- Do not touch or short-circuit the contacts of the rechargeable batteries.

- A slightly acidic, flammable liquid can escape from defective rechargeable batteries! Rinse immediately with

plenty of water if battery fluid gets in contact with your skin. If battery fluid gets into your eyes, wash your

eyes with clean water and seek medical attention immediately!

- Remove the batteries from the machine before you adjust, set up, maintain or clean the machine.

- Ensure that the machine is switched off before you insert the rechargeable battery.

- Remove the rechargeable battery from the machine when you put it down, transport it or store it unattended.

- Do not use this machine when you are tired, or under the influence of drugs, alcohol or medicaments. Be

aware of what you are doing. Stay alert and use common sense.

- Keep children and bystanders at a distance while you are operating the machine. Distractions can cause

you to lose control of the machine.

- Use eye protection, dust mask and hearing protection. Appropriate safety equipment, used

under proper conditions, will reduce the risk of injuries.

Instructions for service and maintenance:

- Cleaning the machine regularly, especially the adjustment elements and the guiding devices, is an important

safety factor.

- Ensure that only genuine MAFELL spare parts and accessories are used. Failure to do so will make

warranty claims and the liability of the manufacturer null and void.

- Prepare a periodic maintenance schedule for your machine. When you clean the machine, be careful

not to disassemble any part of the machine. Reassembling the machine bears the risk that internal

wires are routed incorrectly or pinched, or that return springs of the safety device are mounted

incorrectly. Certain cleaning agents, such as gasoline, carbon tetrachloride, ammonia, etc. can damage

plastic parts.

KSS40 18 M bl

09/2022

11

- Some of the dust produced by sawing, sanding, drilling and other building work contains chemicals

known to cause cancer, birth defects or other reproductive harm. Some examples of these

chemicals are:

- Lead from lead-based paints,

- Crystalline silica from bricks and cement and other masonry products,

- Arsenic and chromium from chemically treated wood.

Your risk from this hazard varies with the frequency at which you perform this type of work. To reduce your

exposure to these chemicals: Work in a well-ventilated area. Work only with approved safety equipment,

such as dust masks that are specially designed to filter out particles of microscopic size.

3.4 Specific safety rules

Sawing method

- DANGER: Keep hands away from cutting area and the blade. Keep your second hand on auxiliary

handle, or motor housing. If both hands are holding the saw, they cannot be cut by the blade.

Fig. 3: Incorrect sawing vs. correct sawing

- Do not reach underneath the workpiece. The guard cannot protect you from the blade below the

workpiece.

- Adjust the cutting depth to the thickness of the workpiece. Less than a full tooth of the blade teeth

should be visible below the workpiece.

- Never hold the workpiece in your hands or across your leg while cutting. Secure the workpiece to a

stable platform. It is important to support the work properly to minimize body exposure, blade binding, or

loss of control.

- Hold the power tool by insulated gripping surfaces, when performing an operation where the cutting

tool may contact hidden wiring. Contact with a "live" wire will also make exposed metal parts of the power

tool "live" and could give the operator an electric shock.

- When ripping, always use a rip fence or straight edge guide. This improves the accuracy of cut and

reduces the chance of blade binding.

- Always use blades with correct size and shape (diamond versus round) of arbour holes. Blades that

do not match the mounting hardware of the saw will run off-centre, causing loss of control.

- Never use damaged or incorrect blade washers or bolt. The blade washers and bolt were specially

designed for your saw, for optimum performance and safety of operation.

KSS40 18 M bl

12

09/2022

Kickback - causes and related safety instructions

- Kickback is a sudden reaction to a pinched, jammed or misaligned saw blade, causing an uncontrolled saw

to lift up and out of the workpiece toward the operator;

- When the blade is pinched or jammed tightly by the kerf closing down, the blade stalls and the motor

reaction drives the unit rapidly back toward the operator;

- If the blade becomes twisted or misaligned in the cut, the teeth at the back edge of the blade can dig into the

top surface of the wood causing the blade to climb out of the kerf and jump back toward the operator.

Fig. 4: Kickback of the machine

Kickback is the result of saw misuse and/or incorrect operating procedures or conditions and can be avoided

by taking proper precautions as given below.

- Maintain a firm grip with both hands on the saw and position your arms to resist kickback forces.

Position your body to either side of the blade, but not in line with the blade. Kickback could cause the

saw to jump backwards, but kickback forces can be controlled by the operator, if proper precautions are

taken.

- When blade is binding, or when interrupting a cut for any reason, release the trigger and hold the

saw motionless in the material until the blade comes to a complete stop. Never attempt to remove

the saw from the work or pull the saw backward while the blade is in motion or kickback may occur.

Investigate and take corrective actions to eliminate the cause of blade binding.

- When restarting a saw in the workpiece, centre the saw blade in the kerf so that the saw teeth are

not engaged into the material. If a saw blade binds, it may walk up or kickback from the workpiece as the

saw is restarted.

KSS40 18 M bl

09/2022

13

- Support large panels to minimise the risk of blade pinching and kickback. Large panels tend to sag

under their own weight. Supports must be placed under the panel on both sides, near the line of cut and

near the edge of the panel.

Fig. 5: Incorrect support vs. correct support

- Do not use dull or damaged blades. Unsharpened or improperly set blades produce narrow kerf causing

excessive friction, blade binding and kickback.

- Blade depth and bevel adjusting locking levers must be tight and secure before making the cut. If

blade adjustment shifts while cutting, it may cause binding and kickback.

- Use extra caution when sawing into existing walls or other blind areas. The protruding blade may cut

objects that can cause kickback.

Function of the lower guard

- Check the lower guard for proper closing before each use. Do not operate the saw if the lower guard

does not move freely and close instantly. Never clamp or tie the lower guard into the open position.

If the saw is accidentally dropped, the lower guard may be bent. Raise the lower guard with the retracting

handle and make sure it moves freely and does not touch the blade or any other part, in all angles and

depths of cut.

- Check the operation of the lower guard spring. If the guard and the spring are not operating

properly, they must be serviced before use. Lower guard may operate sluggishly due to damaged parts,

gummy deposits, or a build-up of debris.

- The lower guard may be retracted manually only for special cuts such as "plunge cuts" and

"compound cuts". Raise the lower guard by the retracting handle and as soon as the blade enters

the material, the lower guard must be released. For all other sawing, the lower guard should operate

automatically.

- Always observe that the lower guard is covering the blade before placing the saw down on bench or

floor. An unprotected, coasting blade will cause the saw to walk backwards, cutting whatever is in its path.

Be aware of the time it takes for the blade to stop after switch is released.

KSS40 18 M bl

14

09/2022

Function of the riving knife

- Use the appropriate saw blade for the riving knife. For the riving knife to function, the body of the blade

must be thinner than the riving knife and the cutting width of the blade must be wider than the thickness of

the riving knife.

- Adjust the riving knife as described in this instruction manual. Incorrect spacing, positioning and

alignment can make the riving knife ineffective in preventing kickback.

- Always use the riving knife except when plunge cutting. The riving knife must be replaced after plunge

cutting. The riving knife causes interference during plunge cutting and can create kickback.

- For the riving knife to work, it must be engaged in the workpiece. The riving knife is ineffective in

preventing kickback during short cuts.

- Do not operate the saw if the riving knife is bent Even a light interference can slow the closing rate of a

guard.

RETAIN THESE INSTRUCTIONS!

KSS40 18 M bl

09/2022

15

3.5 Safety devices

Danger

Risk of injury from missing safety devices

These devices are necessary for the safe operation of the machine. They must

not be removed or rendered ineffective.

➢ Check the proper functioning of the safety devices before you start

operating the machine.

➢ Never use the machine with missing or ineffective safety devices.

The machine is equipped with the following safety devices:

Safety device

Type of check

Upper fixed guard

Visual check for damage

Lower movable guard

Functional check (complete opening and jerk-free

abrupt closing)

Large base plate

Visual check for damage and deformation

Handles

Visual check for damage

Riving knife/splitter

Visual check for damage and deformation

Motor brake

Functional check (braking time must not be longer

than 2 seconds)

Hose connector

Visual check for damage and obstruction

If the safety devices are damaged or not functioning properly, follow the instructions in the chapter

Troubleshooting. For other malfunctions, please contact your dealer or MAFELL Customer Service directly.

KSS40 18 M bl

16

09/2022

3.6 Residual risks

Warning

Risk of injury when working with the machine

Even when the machine is used as intended and in compliance with the safety

regulations, there are still residual risks caused by the intended use, which can

have consequences for your health.

➢ Observe the safety instructions and information in these instructions.

➢ Always be extremely careful and cautious when you work with the machine.

The existing residual risks include:

- Contact with the saw blade in the area of the start-up opening below the base plate.

- Contact with the part of the saw blade that protrudes below the workpiece during the cutting process.

- Contact with rotating parts from the side: Saw blade, clamping flange and flange bolt.

- Kickback of the machine when jammed in the workpiece.

- Breakage and ejection of the saw blade or parts of the saw blade.

- Impaired hearing when working without hearing protection for long periods of time.

- Emission of harmful wood dusts during longer operation without extraction.

- FLEXI bar snapping open in case of improper use.

4 Setup / adjustment

4.1 Charging the rechargeable battery

Rechargeable battery and charger are matched to each other. Use only the MAFELL chargers for charging.

First, charge the rechargeable battery when you use a new machine.

The charging process is described in the "Charger APS M" instructions supplied.

A significantly shortened operating time after charging indicates that the rechargeable battery is exhausted and

needs to be replaced.

The rechargeable battery is equipped with a temperature monitor. This ensures that the rechargeable battery is

only charged in the optimal temperature range between 0 °C (32 °F) and 50 °C (122 °F). This ensures a long

battery life.

KSS40 18 M bl

09/2022

17

Warning

Risk of fire and explosion due to overheating or moisture

High temperatures and moisture can cause short-circuits in the rechargeable

battery. There is a risk of fire and explosion.

➢ Protect the rechargeable battery from heat, fire and moisture.

➢ Do not expose the rechargeable battery to temperatures above 50 °C (122

°F).

➢ Store the rechargeable battery at a temperature between 10 °C (50 °F)

and 30 °C (86 °F).

➢ Allow the rechargeable battery to cool down before you start charging it.

4.2 Inserting the rechargeable battery

Prior to inserting the battery, check to ensure that the rated voltage of the rechargeable battery matches the

specification on the machine.

Use the following procedure to insert the

rechargeable battery into the machine:

1. Insert the charged rechargeable battery into

the battery guide until you feel that it locks into

place.

2. Check to ensure that the battery is firmly

seated in the machine.

✓ The rechargeable battery is inserted in

the machine.

Fig. 6: Inserting the rechargeable battery into the machine

4.3 Removing the rechargeable battery

Use the following procedure to remove the

rechargeable battery:

1. Press and hold the lever (10) of the battery

lock.

2. Pull the rechargeable battery out of the guide.

✓ The rechargeable battery is removed.

Fig. 7: Removing the rechargeable battery

KSS40 18 M bl

18

09/2022

4.4 Chip extraction

Caution

Health hazards from wood dust

The dusts produced during work can be inhaled and can cause health damage.

➢ Harmful dust must be extracted with a HEPA 13 dust extractor.

➢ Wear a dust mask during work.

For all work that produces a significant amount of dust, connect the machine to a suitable external extraction

device. The air velocity must be at least 20 m/s [65 ft/sec].

The outside diameter of the hose connector is 28 mm [1.1 in].

For short-time work that generates a small amount of dust, you can use the shavings bag provided as a self-

suction device.

4.5 Saw blade selection

To achieve good cutting quality, use a sharp tool and select a tool from the following list that is appropriate for

material and application:

Cutting softwood and hardwood across and along the grain direction:

- Carbide circular saw blade Ø 120 x 1.8 x 20 mm, 24 teeth [Ø 4.72 x 0.07 x 0.79 in]

Cutting softwood and hardwood especially along the grain direction:

- Carbide circular saw blade Ø 120 x 1.8 x 20 mm, 12 teeth [Ø 4.72 x 0.07 x 0.79 in]

Cutting softwood and hardwood especially across the grain direction:

- Carbide circular saw blade Ø 120 x 1.8 x 20 mm, 40 teeth [Ø 4.72 x 0.07 x 0.79 in]

Cutting laminate:

- Carbide circular saw blade Ø 120 x 1.8 x 20 mm, 40 teeth [Ø 4.72 x 0.07 x 0.79 in]

Cutting wood fiber insulation material:

- Carbide circular saw blade Ø 120 x 1.8 x 20 mm, 40 teeth [Ø 4.72 x 0.07 x 0.79 in]

Cutting plastic material (styrofoam):

- Carbide circular saw blade Ø 120 x 1.8 x 20 mm, 24 teeth [Ø 4.72 x 0.07 x 0.79 in]

KSS40 18 M bl

09/2022

19

4.6 Changing the saw blade

Caution

Risk of injury from the sharp saw blade

The saw blade is sharp. You can hurt yourself when you change the saw blade.

➢ Wear protective gloves when you change the saw blade.

➢ Be careful when you change the saw blade.

Use the following procedure to change the saw

blade:

1. Pull the rechargeable battery out of the

machine.

2. Put the machine on a flat surface.

3. To move the movable guard to the maximum

open position, either use the pre-feed lever (3)

or do it manually.

➢ To remove the saw blade, manually hold

the guard in the open position.

Fig. 8: Opening the guard

4. Press and hold the locking pin (11).

Fig. 9: Actuating the locking pin

KSS40 18 M bl

20

09/2022

5. Insert the Allen key (B) into the flange screw

(12) and turn it counterclockwise until the

saw shaft engages in the locking device.

➢ The saw blade is retained in position and

the flange screw can be released.

6. Using the Allen key (B), turn the flange screw

(12) counterclockwise to loosen it.

➢ You can now release the locking pin.

7. Remove the flange screw (12) and the front

clamping flange (13).

8. Remove the old saw blade.

➢ Clamping flanges must be free of

adhering parts!

➢ The new saw blade can now be installed.

Fig. 10: Removing the old saw blade

9. Position the new saw blade (14) on the rear

flange (16).

➢ Ensure that the direction of rotation is

correct when you install the saw blade.

The saw teeth or the arrow on the saw

blade (14) must point in the direction of

the arrow (15) on the machine.

10. Fit clamping flange (13) and flange screw (12).

Fig. 11: Replacing the saw blade

La page est en cours de chargement...

Mafell KSS 40 18M bl Mode d'emploi

Mafell KSS 40 18M bl Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents