Allied Telesis AT-AP500 Quick Installation Manual

Marque: Allied Telesis

Modèle: AT-AP500

Taper: Quick Installation Manual

Installation and User’s Guides

This document contains an abbreviated version of the installation instructions for the

AT-AP500 Wireless Access Point. For complete installation and management instructions,

refer to the AT-AP500 Installation Guide and AlliedView™ Cloud User’s Guide on the Allied

Telesis web site at www.alliedtelesis.com/services-and-support.

Safety and Electromagnetic Emissions Certificates

For Safety and Electromagnetic Emissions certificates, refer to the AT-AP500 Installation

Guide.

Installation Options

This quick installation guide explains how to install the device on a wall or ceiling.

Physical Description

For a physical description of the AT-AP500 Wireless Access Point, refer to the AT-AP500

Installation Guide.

Package Contents of the AT-AP500 Wireless Access Point

The following items should be in the shipping container:

 One AT-AP500 Wireless Access Point

 This AT-AP500 Quick Installation Guide

 One mounting-bracket screw

 One bracket and one base plate for wall or ceiling mounting

If you are not planning to use the PoE+ feature of the access point to power the device, you

must separately order the AT-TQ0091 AC/DC Power Adapter. For installation information

on the adapter, refer to the AT-AP500 Installation Guide.

If any item is missing or damaged, contact your Allied Telesis sales representative for

assistance. You should retain the original shipping material in case you need to return the

unit to Allied Telesis.

Installing the Wireless Access Point on a Wall or Ceiling

To install the access point on a wall or ceiling, perform the following procedure:

1. Using the base plate as a template, mark the four holes for mounting the base plate

to the wall or ceiling.

2. Drill the holes for the four self-tapping screws, and if applicable, two wall anchors.

3. If using wall anchors, install the wall anchors.

4. Mount the base plate to the wall or ceiling using the self-tapping screws.

5. Place the access point upside down on a flat surface

6. Place the bracket against the bottom of the access point and use the bracket to push

downward on the stopper nub, then turn the bracket in the direction of the arrows

shown here until the two hooks hold the bracket, the stopper nub pops up, and the

bracket locks in place.

7. Attach the mounting-bracket screw through the notch in the mounting bracket to the

access point to fasten the bracket to the access point.

8. Have someone hold the bottom of the access point next to the base plate attached to

the wall or ceiling and insert the two base-plate pins into the circles of the keyhole

slots.

9. Slide the access point downward to lock the necks of the base-plate pins in the slots.

10. Fasten the access point to the base plate by turning the base-plate captive screw

clockwise using a Phillips-head screwdriver.

11. Connect a network cable to the LAN port on the rear panel of the access point.

12. Connect the other end of the network cable to a port on the PoE enabled networking

device (for example, Ethernet switch, midspan power-sourcing device).

Kensington Lock

A Kensington lock can be used to secure the device. For the location of the lock, refer to

the AT-AP500 Installation Guide.

Starting the Initial Management Session

This section contains an abbreviated version of the procedure for starting the initial

management session. For complete instructions, refer to the AT-AP500 installation Guide

or AlliedView Cloud User’s Guide.

You must have the following to initiate a management session on the access point:

 Network with a DHCP server and a route for the access point to the Internet. When

you power on the access point for the first time, it will obtain an IP address from the

DHCP server, and then it must be able to access the Internet to register itself with the

AlliedView Cloud service.

 Serial number for the access point.

To start the initial management session, perform the following procedure:

1. Create an AlliedView Cloud account at avcloud.alliedtelesis.com for the

management of the access points. Refer to the AlliedView Cloud User’s Guide.

2. Add one or more access points to the account by entering the access point name

and serial number. Refer to the AlliedView Cloud User’s Guide.

Quick Installation Guide

AT-AP500

Cloud Managed Enterprise-class Wireless Access Point

with IEEE802.11 a/b/g/n/ac Dual Radio

613-002285 Rev. C

*613-002285 Rev C*

1 2 3

3. If not done already, power on the access point: the access point automatically

registers with the AlliedView Cloud once a name and serial number is assigned, and

the unit is powered up.

4. Refer to the AlliedView Cloud User’s Guide to add the access point to the network

and configure the access point.

LEDs

The LEDs on the top panel of the access point are described in this table.

Federal Communication Commission Interference Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following

two conditions: (1) This device may not cause harmful interference, and (2) this device

must accept any interference received, including interference that may cause undesired

operation.

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the user

is encouraged to try to correct the interference by one of the following measures:

 Reorient or relocate the receiving antenna.

 Increase the separation between the equipment and receiver.

 Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

 Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party

responsible for compliance could void the user's authority to operate this equipment.

This transmitter must not be co-located or operating in conjunction with any other antenna

or transmitter.

For operation within 5.15 ~ 5.25GHz / 5.47 ~5.725GHz frequency range, it is restricted to

indoor environment. The band from 5600-5650MHz will be enabled by the software during

the manufacturing and cannot be changed by the end user. This device meets all the other

requirements specified in Part 15E, Section 15.407 of the FCC Rules.

Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled

environment. This equipment should be installed and operated with minimum distance

26cm between the radiator & your body.

Note

The country code selection is for non-US model only and is not available to all US

model. Per FCC regulation, all WiFi product marketed in US must fixed to US

operation channels only.

Industry Canada Statement

This device complies with ISED’s license-exempt RSSs. Operation is subject to the

following two conditions: (1) This device may not cause harmful interference, and (2) this

device must accept any interference received, including interference that may cause

undesired operation.

Le présent appareil est conforme aux CNR d’ ISED applicables aux appareils radio

exempts de licence. L’exploitation est autorisée aux deux conditions suivantes: (1) le

dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit accepter

tout brouillage reçu, y compris un brouillage susceptible de provoquer un fonctionnement

indésirable.

Caution:

(i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the

potential for harmful interference to co-channel mobile satellite systems;

(ii) the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and

5470-5725 MHz shall comply with the e.i.r.p. limit;

(iii) the maximum antenna gain permitted for devices in the band 5725-5825 MHz shall

comply with the e.i.r.p. limits specified for point-to-point and non point-to-point operation as

appropriate; and

(iv) Users should also be advised that high-power radars are allocated as primary users

(i.e. priority users) of the bands 5.26-5.32GHz, 5.50-5.58GHz and 5.66-5.70GHz and that

these radars could cause interference and/or damage to LE-LAN devices.

Avertissement:

Le guide d’utilisation des dispositifs pour réseaux locaux doit inclure des instructions

précises sur les restrictions susmentionnées, notamment:

(i) les dispositifs fonctionnant dans la bande 5 150-5 250 MHz sont réservés uniquement

pour une utilisation à l’intérieur afin de réduire les risques de brouillage préjudiciable aux

systèmes de satellites mobiles utilisant les mêmes canaux;

(ii) le gain maximal d’antenne permis pour les dispositifs utilisant les bandes 5.26-5.32GHz,

5.50-5.58GHz and 5.66-5.70GHz doit se conformer à la limite de p.i.r.e.;

(iii) le gain maximal d’antenne permis (pour les dispositifs utilisant la bande 5 725-5 825

MHz) doit se conformer à la limite de p.i.r.e. spécifiée pour l’exploitation point à point et non

point à point, selon le cas.

(iv) De plus, les utilisateurs devraient aussi être avisés que les utilisateurs de radars de

haute puissance sont désignés utilisateurs principaux (c.-àd., qu’ils ont la priorité) pour les

bandes 5.26-5.32GHz, 5.50-5.58GHz and 5.66-5.70GHz et que ces radars pourraient

causer du brouillage et/ou des dommages aux dispositifs LAN-EL.

Radiation Exposure Statement:

This equipment complies with ISED radiation exposure limits set forth for an uncontrolled

environment. This equipment should be installed and operated with minimum distance

26cm between the radiator & your body.

Déclaration d'exposition aux radiations:

Cet équipement est conforme aux limites d'exposition aux rayonnements ISED établies

pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un

minimum de 26 cm de distance entre la source de rayonnement et votre corps.

European Union Restriction of the Use of Certain Hazardous

Substances (RoHS) in Electrical and Electronic Equipment

This Allied Telesis RoHS-compliant product conforms to the European Union Restriction of

the Use of Certain Hazardous Substances (RoHS) in Electrical and Electronic Equipment.

Allied Telesis ensures RoHS conformance by requiring supplier Declarations of Conformity,

monitoring incoming materials, and maintaining manufacturing process controls.

Europe - EU Declaration of Conformity

This device complies with the essential requirements of the R&TTE Directive 1999/5/EC.

For more information, refer to the AT-AP500 Installation Guide.

Product Specifications

For product specifications, refer to the AT-AP500 Installation Guide.

No part of this publication may be reproduced without prior written permission from Allied

Telesis, Inc.

Allied Telesis and the Allied Telesis logo are trademarks of Allied Telesis, Incorporated. All

other product names, company names, logos or other designations mentioned herein are

trademarks or registered trademarks of their respective owners.

Allied Telesis, Inc. reserves the right to make changes in specifications and other

information contained in this document without prior written notice. The information

provided herein is subject to change without notice. In no event shall Allied Telesis, Inc. be

liable for any incidental, special, indirect, or consequential damages whatsoever, including

but not limited to lost profits, arising out of or related to this manual or the information

contained herein, even if Allied Telesis, Inc. has been advised of, known, or should have

known, the possibility of such damages.

LED State Description

PWR Solid

Green

The unit is receiving DC power that is within the normal

operating range.

Off The power supply is not receiving power from either the

AC/DC power adapter or a PoE+ Ethernet switch.

SYS Solid

Amber

The access point is loading its firmware or there is a

system fault.

Off The unit is operating normally.

LAN Solid

Green

The Ethernet port is operating at 1000 Mbps.

Flashing

Green

The Ethernet port is operating at 1000 Mbps with link

activity.

Solid

Amber

The Ethernet port is operating at 10/100 Mbps.

Flashing

Amber

The Ethernet port is operating at 10/100 Mbps with link

activity.

2.4GHz Solid

Green

The 2.4GHz radio is sending and receiving radio waves.

5GHz Solid

Green

The 5GHz radio is sending and receiving radio waves.

4 5 6

Allied Telesis AT-AP500 Quick Installation Manual

Marque: Allied Telesis

Modèle: AT-AP500

Taper: Quick Installation Manual

Télécharger le PDF

rapport

dans d''autres langues

English: Allied Telesis AT-AP500

Allied Telesis AT-AP500 Quick Installation Manual

Allied Telesis AT-AP500 Quick Installation Manual

dans d''autres langues

Autres documents