DeWalt DCT416S1 Manuel utilisateur

DCT416

12V Max* Cordless Imaging Thermometer

Thermomètre imageur sans fil 12 V max*

Dispositivo termográfico inalámbrico de 12 V Máx*

INSTRUCTION MANUAL

GUIDE D'UTILISATION

MANUAL DE INSTRUCCIONES

INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE

GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE

USAR EL PRODUCTO.

If you have questions or comments, contact us.

Pour toute question ou tout commentaire, nous contacter.

Si tiene dudas o comentarios, contáctenos.

1-800-4-DEWALT • www.dewalt.com

1

English

SAVE ALL WARNINGS AND INSTRUCTIONS

FOR FUTURE REFERENCE

Work Area Safety

a) Keep work area clean and well lit. Cluttered or dark areas

invite accidents.

b) Keep children and bystanders away while operating an

imaging thermometer. Distractions can cause you to lose

control.

Personal Safety

a) Stay alert, watch what you are doing and use common

sense when operating an imaging thermometer. Do not

use an imaging thermometer while you are tired or under

the influence of drugs, alcohol or medication. A moment of

inattention while operating the imaging thermometer may result

in serious personal injury.

b) Do not overreach. Keep proper footing and balance at all

times. This enables better control of the imaging thermometer

in unexpected situations.

Use and Care

a) Store an idle imaging thermometer out of the reach of

children and do not allow persons unfamiliar with the

imaging thermometer or these instructions to operate

the imaging thermometer. The imaging thermometer may be

dangerous in the hands of untrained users.

b) Use the imaging thermometer, accessories, etc. in

accordance with these instructions, taking into account

the working conditions and the work to be performed.

Use of the imaging thermometer for operations different from

those intended could result in a hazardous situation.

Deﬁ nitions: Safety Guidelines

The definitions below describe the level of severity for each

signal word. Please read the manual and pay attention to these

symbols.

DANGER: Indicates an imminently hazardous situation

which, if not avoided, will result in death or serious injury.

WARNING: Indicates a potentially hazardous situation

which, if not avoided, could result in death or serious injury.

CAUTION: Indicates a potentially hazardous situation which,

if not avoided, may result in minor or moderate injury.

NOTICE: Indicates a practice not related to personal injury

which, if not avoided, may result in property damage.

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR

ANY D

EWALT TOOL, CALL US TOLL FREE AT: 1-800-4-DEWALT

(1-800-433-9258).

WARNING: To reduce the risk of injury, read the instruction

manual.

Important Safety Instructions

• Read these instructions.

• Keep these instructions.

• Heed all warnings.

• Follow all instructions.

• Only use attachments/accessories specified by the manufacturer.

• Refer all servicing to qualified service personnel. Servicing is

required when the apparatus has been damaged in any way,

the apparatus has been exposed to rain or moisture, does not

operate normally, or has been dropped.

2

English

Battery Tool Use and Care

a) Recharge only with the charger specified by DEWALT. A

charger that is suitable for one type of battery pack may create

a risk of fire when used with another battery pack.

b) When battery pack is not in use, keep it away from other

metal objects like paper clips, coins, keys, nails, screws,

or other small metal objects that can make a connection

from one terminal to another. Shorting the battery terminals

together may cause burns or a fire.

c) Under abusive conditions, liquid may be ejected from

the battery; avoid contact. If contact accidentally occurs,

flush with water. If liquid contacts eyes, additionally seek

medical help. Liquid ejected from the battery may cause

irritation or burns.

Safety Information for Imaging

Thermometers

WARNING:

• Do not disassemble or modify the imaging thermometer.

Have the imaging thermometer serviced by a qualified

repair person using only identical replacement parts. This

will ensure that the safety of the power tool is maintained. If you

need assistance contact D

EWALT at 1-800-4-DEWALT (1-800-

433-9258) or go to http://www.dewalt.com on the Internet.

• Do not operate the imaging thermometer in explosive

atmospheres, such as in the presence of flammable liquids,

gases, or dust. Imaging thermometers create sparks which may

ignite the dust or fumes.

• The imaging thermometer should only be used with

specifically designated D

EWALT batteries. Use of any other

batteries may create a risk of fire.

• Store the imaging thermometer out of reach of children and

other untrained persons. Tools are dangerous in the hands of

untrained users.

• Do not remove or deface warning labels.

• Do not use imaging thermometer for testing temperatures

of cooked or uncooked food.

• Do not touch surfaces to confirm hot temperature readings.

• Do not use for taking human or animal body temperatures.

WARNING: Burn hazard. The reading may not be accurate if the

imaging thermometer is in the presence of strong electromagnetic

fields (such as arc welders, induction heaters, ratio transmitters, etc.).

Do not use the imaging thermometer under these conditions.

WARNING: The imaging thermometer measures surface

temperature only. Objects behind the surface may have significantly

different temperatures, posing a burn or frostbite hazard.

WARNING: See emissivity information for actual temperatures.

Reflective objects result in lower than actual temperature

measurements and can pose a burn hazard.

WARNING: Do not expose imaging thermometer to excessive

heat such as sunshine, fire or the like.

CAUTION: When not in use, place imaging thermometer on

its side on a stable surface where it will not cause a tripping or

falling hazard. Some tools with large battery packs will stand upright

on the battery pack but may be easily knocked over.

NOTICE: Modifications not authorized by the manufacturer may void

user's authority to operate this device.

NOTICE: To avoid damage to the imaging thermometer, do

not leave it exposed to high temperature environments or heat

sources, for example, in a vehicle in the sun. Always operate the

imaging thermometer within the operating range noted in the

specification chart.

3

English

NOTICE: Do not point the imaging thermometer (with or without the

lens cover engaged) at the sun or other intensive energy sources that

emit laser radiation. This can damage the detector inside the imaging

thermometer and can effect the accuracy.

MICRO SD MEMORY CARD

WARNING: Choking hazard. The micro SD memory card is a

small part that could lead to a choking hazard and is not intended for

children.

NOTICE: It is recommended to use the micro SD memory card

supplied with the imaging thermometer. D

EWALT does not warrant

the use or reliability of other aftermarket cards with different brands

or capacities. It is also recommended to frequently transfer the saved

images to a computer as a backup.

Regulatory Notices

• This Class B digital apparatus complies with Canadian ICES-003.

• This device complies with Part 15 of the FCC Rules. Operation is

subject to the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including

interference that may cause undesired operation.

NOTE: This equipment has been tested and found to comply with

the limits for a Class B digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off and

on, the user is encouraged to try to correct the interference by one or

more of the following measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and receiver.

– Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

– Consult the dealer or an experienced radio/TV technician for help.

Important Safety Instructions for All

Battery Packs

When ordering replacement battery packs, be sure to include catalog

number and voltage. Consult the chart at the end of this manual for

compatibility of chargers and battery packs.

The battery pack is not fully charged out of the carton. Before using

the battery pack and charger, read the safety instructions below, then

follow charging procedures outlined.

READ ALL INSTRUCTIONS

• Do not charge or use battery in explosive atmospheres,

such as in the presence of flammable liquids, gases or dust.

Inserting or removing the battery from the charger may ignite the

dust or fumes.

• NEVER force battery pack into charger. DO NOT modify

battery pack in any way to fit into a non-compatible charger

as battery pack may rupture causing serious personal injury.

Consult the chart at the end of this manual for compatibility of

batteries and chargers.

• Charge the battery packs only in D

EWALT chargers.

• DO NOT splash or immerse in water or other liquids.

• Do not store or use the tool and battery pack in locations

where the temperature may reach or exceed 105 ˚F (40 ˚C)

(such as outside sheds or metal buildings in summer).

4

English

• Contents of opened battery cells may cause respiratory

irritation. Provide fresh air. If symptoms persists, seek medical

attention.

WARNING: Burn hazard. Battery liquid may be flammable if

exposed to spark or flame.

The RBRC™ Seal

The RBRC™ (Rechargeable Battery Recycling

Corp oration) Seal on the nickel cadmium, nickel metal

hydride or lithium ion batteries (or battery packs) indicate

that the costs to recycle these batteries (or battery

packs) at the end of their useful life have already been paid by D

EWALT.

In some areas, it is illegal to place spent nickel cadmium, nickel metal

hydride or lithium ion batteries in the trash or municipal solid waste

stream and the RBRC program provides an environmentally conscious

alternative.

RBRC™ in cooperation with D

EWALT and other battery users, has

established programs in the United States and Canada to facilitate

the collection of spent nickel cadmium, nickel metal hydride or lithium

ion batteries. Help protect our environment and conserve natural

resources by returning the spent nickel cadmium, nickel metal hydride

or lithium ion batteries to an authorized D

EWALT service center or

to your local retailer for recycling. You may also contact your local

recycling center for information on where to drop off the spent battery.

RBRC™ is a registered trademark of the Rechargeable Battery

Recycling Corporation.

Important Safety Instructions for All

Battery Chargers

SAVE THESE INSTRUCTIONS: This manual contains important

safety and operating instruc tions for battery chargers.

• Before using charger, read all instructions and cautionary markings

on charger, battery pack, and product using battery pack.

WARNING: Fire hazard. Never attempt to open the battery pack

for any reason. If battery pack case is cracked or damaged, do not

insert into charger. Do not crush, drop or damage battery pack. Do

not use a battery pack or charger that has received a sharp blow,

been dropped, run over or damaged in any way (i.e., pierced with a

nail, hit with a hammer, stepped on). Damaged battery packs should

be returned to service center for recycling.

WARNING: Fire hazard. Do not store or carry battery so

that metal objects can contact exposed battery terminals.

For example, do not place battery in aprons, pockets, tool boxes,

product kit boxes, drawers, etc., with loose nails, screws, keys, etc.

Transporting batteries can possibly cause fires if the battery

terminals inadvertently come in contact with conductive

materials such as keys, coins, hand tools and the like. The US

Department of Transportation Hazardous Material Regulations (HMR)

actually prohibit transporting batteries in commerce or on airplanes

(i.e., packed in suitcases and carry-on luggage) UNLESS they are

properly protected from short circuits. So when transporting individual

batteries, make sure that the battery terminals are protected and well

insulated from materials that could contact them and cause a short

circuit.

SPECIFIC SAFETY INSTRUCTIONS FOR LITHIUM ION (Li-Ion)

• Do not incinerate the battery pack even if it is severely

damaged or is completely worn out. The battery pack can

explode in a fire. Toxic fumes and materials are created when

lithium ion battery packs are burned.

• If battery contents come into contact with the skin,

immediately wash area with mild soap and water. If battery

liquid gets into the eye, rinse water over the open eye for 15minutes

or until irritation ceases. If medical attention is needed, the battery

electrolyte is composed of a mixture of liquid organic carbonates

and lithium salts.

5

English

WARNING: Shock hazard. Do not allow any liquid to get inside

charger. Electric shock may result.

CAUTION: Burn hazard. To reduce the risk of injury, charge only

D

EWALT rechargeable batteries. Other types of batteries may burst

causing personal injury and damage.

NOTICE: Under certain conditions, with the charger plugged in to the

power supply, the charger can be shorted by foreign material. Foreign

materials of a conductive nature such as, but not limited to, grinding

dust, metal chips, steel wool, aluminum foil, or any buildup of metallic

particles should be kept away from charger cavities. Always unplug the

charger from the power supply when there is no battery pack in the

cavity. Unplug charger before attempting to clean.

WARNING:

• DO NOT attempt to charge the battery pack with any

chargers other than the ones in this manual. The charger and

battery pack are specifically designed to work together.

• These chargers are not intended for any uses other than

charging D

EWALT rechargeable batteries. Any other uses may

result in risk of fire, electric shock or electrocution.

• Do not expose charger to rain or snow.

• Pull by plug rather than cord when disconnecting charger.

This will reduce risk of damage to electric plug and cord.

• Make sure that cord is located so that it will not be stepped

on, tripped over, or otherwise subjected to damage or

stress.

• Do not use an extension cord unless it is absolutely

necessary. Use of improper extension cord could result in risk of

fire, electric shock, or electrocution.

• When operating a charger outdoors, use an extension cord

suitable for outdoor use. Use of a cord suitable for outdoor use

reduces the risk of electric shock.

• An extension cord must have adequate wire size (AWG

or American Wire Gauge) for safety. The smaller the gauge

number of the wire, the greater the capacity of the cable, that is

16 gauge has more capacity than 18 gauge. An undersized cord

will cause a drop in line voltage resulting in loss of power and

overheating. When using more than one extension to make up the

total length, be sure each individual extension contains at least the

minimum wire size. The following table shows the correct size to

use depending on cord length and nameplate ampere rating. If in

doubt, use the next heavier gauge. The smaller the gauge number,

the heavier the cord.

Minimum Gauge for Cord Sets

Ampere Rating

Volts Total Length of Cord in Feet (meters)

120V 25 (7.6) 50 (15.2) 100 (30.5) 150 (45.7)

240V 50 (15.2) 100 (30.5) 200 (61.0) 300 (91.4)

More

Than

Not More

Than

AWG

0 6 18 16 16 14

610 18 16 14 12

10 12 16 16 14 12

12 16 14 12 Not Recommended

• Do not place any object on top of charger or place the

charger on a soft surface that might block the ventilation

slots and result in excessive internal heat. Place the charger

in a position away from any heat source. The charger is ventilated

through slots in the top and the bottom of the housing.

• Do not operate charger with damaged cord or plug.

• Do not operate charger if it has received a sharp blow, been

dropped, or otherwise damaged in any way. Take it to an

authorized service center.

6

English

• Do not disassemble charger; take it to an authorized service

center when service or repair is required. Incorrect reassembly

may result in a risk of electric shock, electrocution or fire.

• Disconnect the charger from the outlet before attempting

any cleaning. This will reduce the risk of electric shock.

Removing the battery pack will not reduce this risk.

• NEVER attempt to connect two chargers together.

• The charger is designed to operate on standard 120V

household electrical power. Do not attempt to use it on any

other voltage. This does not apply to the vehicular charger.

Chargers

Your tool uses a DEWALT charger. Be sure to read all safety instructions

before using your charger. Consult the chart on the back cover of this

manual for compatibility of chargers and battery packs.

Charging Procedure (Fig. 1)

1. Plug the charger into an

A

FIG. 1

appropriate outlet

before inserting battery

pack.

2. Insert the battery pack

(A) into the charger,

as shown in Figure 1,

making sure the pack is

fully seated in charger.

The red (charging) light

will blink continuously

indicating that the

charging process has

started.

3. The completion of charge will be indicated by the red light

remaining ON continuously. The pack is fully charged and may be

used at this time or left in the charger.

Indicator Light Operation

DCB106

PACK CHARGING

PACK CHARGED

DCB107, DCB112

PACK CHARGING

PACK CHARGED

HOT/COLD DELAY

Charge Indicators

HOT/COLD PACK DELAY

DCB107, DCB112

The DCB107 and DCB112 chargers have a hot/cold delay feature.

When the charger detects a battery that is hot, it automatically delays

charging until the battery has cooled. When the charger detects a

battery that is cold, it automatically delays charging until the battery

has warmed.

The red light will continue to blink, but a yellow indicator light will

be illuminated during this operation. Once the battery has cooled,

the yellow light will turn off and the charger will resume the charging

procedure.

7

English

LEAVING THE BATTERY PACK IN THE CHARGER

The charger and battery pack can be left connected with the charge

indicator showing Pack Charged.

WEAK BATTERY PACKS: Weak batteries will continue to function

but should not be expected to perform as much work.

FAULTY BATTERY PACKS: This charger will not charge a faulty

battery pack. The charger will indicate faulty battery pack by refusing

to light or by displaying problem pack or charger.

NOTE: This could also mean a problem with a charger.

Wall Mounting

DCB107, DCB112

These chargers are designed to be wall mountable or to sit upright on

a table or work surface.

If wall mounting, locate the charger within reach of an electrical outlet.

Mount the charger securely using drywall screws at least 1" (25.4 mm)

long, screwed into wood to an optimal depth leaving approximately

7/32" (5.5 mm) of the screw exposed.

Important Charging Notes

1. Longest life and best performance can be obtained if the battery

pack is charged when the air temperature is between 65 °F and

75 °F (18–24 °C). DO NOT charge the battery pack in an air

temperature below +40 °F (+4.5 °C), or above +105 °F (+40.5 °C).

This is important and will prevent serious damage to the battery

pack.

2. The charger and battery pack may become warm to touch while

charging. This is a normal condition, and does not indicate a

problem. To facilitate the cooling of the battery pack after use,

avoid placing the charger or battery pack in a warm environment

such as in a metal shed, or an uninsulated trailer.

3. If the battery pack does not charge properly:

a. Check operation of receptacle by plugging in a lamp or other

appliance;

b. Check to see if receptacle is connected to a light switch which

turns power off when you turn out the lights;

c. Move charger and battery pack to a location where the

surrounding air temperature is approximately 65 °F–75 °F

(18–24 °C);

d. If charging problems persist, take the tool, battery pack and

charger to your local service center.

4. The battery pack should be recharged when it fails to produce

sufficient power on jobs which were easily done previously. DO

NOT CONTINUE to use under these conditions. Follow the

charging procedure. You may also charge a partially used pack

whenever you desire with no adverse affect on the battery pack.

5. Foreign materials of a conductive nature such as, but not limited

to, grinding dust, metal chips, steel wool, aluminum foil, or any

buildup of metallic particles should be kept away from charger

cavities. Always unplug the charger from the power supply when

there is no battery pack in the cavity. Unplug charger before

attempting to clean.

6. Do not freeze or immerse charger in water or any other liquid.

WARNING: Shock hazard. Don’t allow any liquid to get inside

charger. Electric shock may result.

CAUTION: Never attempt to open the battery pack for any reason.

If the plastic housing of the battery pack breaks or cracks, return to

a service center for recycling.

Storage Recommendations

1. The best storage place is one that is cool and dry away from direct

sunlight and excess heat or cold.

8

English

2. For long storage, it is recommended to store a fully charged

battery pack in a cool dry place out of the charger for optimal

results.

NOTE: Battery packs should not be stored completely depleted of

charge. The battery pack will need to be recharged before use.

SAVE THESE INSTRUCTIONS

FOR FUTURE USE

COMPONENTS (Fig. 2)

WARNING: Never modify the imaging thermometer or any part of

it. Damage or personal injury could result.

A. 12V Max* lithium-ion D. Micro SD card slot cover

battery pack E. Micro SD card slot

B. Handle F. Lens

C. Screen G. Lens cover

H.

Back Arrow Button: Press this button to navigate

backward.

I.

Select Button: Press this button to confirm a selection.

J.

Forward Arrow Button: Press this button to navigate

forward.

K.

Image Blend Adjust Button: Press this button to

change the percentage blend between the visual and

thermal images.

L.

Menu/Power Button: Press this button to power the

unit on (hold for 0.5 seconds) or off (hold for 3 seconds).

When the unit is powered on, press this button to view the

menu options.

M.

Photo Capture Button: Press this button for taking a

photo.

H

I

K

M

J

L

C

B

D, E

F, G

A

FIG. 2

INTENDED USE

The imaging thermometer measures radiated energy from an object's

surface and then uses those measurements to display an image and

estimate temperature.

9

English

OPERATION

Installing and Removing the Battery Pack

(Fig.4)

NOTE: Make sure your battery pack is fully charged.

To install the battery pack (A) into the tool handle, align the battery with

the rails inside the tool’s handle and slide it firmly into the handle until

you hear the lock snap into place.

P

A

FIG. 4

To remove the battery pack from the tool, press the release button (P)

and firmly pull the battery pack out of the tool handle. Insert it into the

charger as described in the charger section of this manual.

Getting Started (Fig. 2)

1. Slide lens cover (G) down to expose the lens.

Power On/Off

1. To turn on the imaging thermometer, push the menu/power button

(L) and hold for 0.5 seconds.

2. To turn off the imaging thermometer, push the menu/power button

(L) and hold for 3 seconds.

INITIAL SETUP

Date and Time Setup

The first time the imaging thermometer is powered on, it will prompt to

set the time and date. After the initial setup, the time and date can be

changed through the menu navigation.

Photos can be taken and then saved (bitmap format) on a micro SD

card.

The imaging thermometer can be used for inspections and trouble

shooting of electrical systems, HVAC, plumbing, mechanical

equipment, residential buildings or automotive systems.

The imaging thermometer is a professional tool. DO NOT let children

come into contact with the tool. Supervision is required when

inexperienced operators use this tool.

ASSEMBLY

Belt Hook (Fig.3) (Optional Accessory)

WARNING: To reduce the risk of serious personal injury, DO

NOT suspend tool overhead or suspend objects from the belt hook.

ONLY hang tool’s belt hook from a work belt.

WARNING: To reduce the risk of serious personal injury,

ensure the screw (N) holding the belt hook is secure.

IMPORTANT: When attaching or

N

O

FIG. 3

removing the belt hook, use only

the screw (N) that is provided.

The belt hook (O) can be

attached to either side of the

tool using only the screw (N)

provided, to accommodate left-

or right-handed users. If the hook

is not desired at all, it can be removed from the tool.

To move belt hook, remove the screw (N) that holds the belt hook in

place then reassemble on the opposite side.

10

English

1. Press the forward (J) or back (H) arrow to highlight the field to

change.

2. Press the select button (I) to activate the field. The field will turn

green.

3. Press the forward (J) or back (H) arrow to change the activated

field.

4. Press the select button (I) to save the changes.

5. Repeat the steps above to change the remaining fields.

6. Press the menu/power button (L) to exit.

BASIC OPERATION

Main Viewing Screen

The main screen includes several sections:

Q. Scanned area image

R. Temperature measurement at center of image (+)

S. Emissivity setting

T. Battery fuel gauge

U. Temperature color scale

R

T

S

Q

U

Image Blend

The DCT416 Imaging Thermometer has the ability to display both a

visual image and an infrared image. The images can also be blended

on the display to provide an overlay of the thermal image on top of the

visual image. A blended image can be helpful in diagnosing trouble

spots or communicating with customers.

To change the blend setting, push the image blend adjust button

(K). The image blend can be pushed repeatedly to cycle through the

following options for display settings:

100% Visual

75% Visual, 25% Thermal

50% Visual, 50% Thermal

25% Visual, 75% Thermal

100% Thermal

Take and Store Photos

Make sure a micro SD card is installed in order to save a photo. Open

micro SD card slot cover (D) and insert the micro SD card into the

slot (E).

11

English

E

D

1. Push photo capture button (M).

2. The displayed image will freeze for 3 seconds in order to review

the photo.

3. Press the forward (J) or back (H) arrow to highlight save to SD

card or delete.

4. Press the select button (I) to confirm selection.

5. After completion of save or delete, the imaging thermometer will

automatically return to the main viewing screen.

NOTE: If no SD card is installed or if there is a problem with the SD

card, the below communication will appear.

NOTE: If the SD card is full, the below communication will appear.

MENU OPTIONS

NOTE: At any time, pushing the menu/power button (L) will return to

the previous menu.

12

English

To View Photos

1. Press the menu/power button (L).

2. Press the forward (J) or back (H) arrow to highlight the folder

option in the menu.

3. Press the select button (I) to confirm selection.

4. Press the forward (J) or back (H) arrow to scroll through saved

images.

5. Press the select button (I) to go to the delete sub-menu.

6. Press the forward (J) or back (H) arrow to highlight save to SD

card or delete.

7. Press the select button (I) to confirm selection.

8. After completion of save or delete, the imaging thermometer will

automatically return to the next sequential image.

Emissivity

Emissivity describes the energy-emitting characteristics of materials.

Most organic materials and painted or oxidized surfaces have an

emissivity of about 0.95 which is the default setting. It is recommended

to compensate for inaccurate readings that may result from measuring

materials with low emissivity values such as shiny metal surfaces. Cover

these surfaces with masking tape or flat black paint (<148˚C/300˚F)

and use the default (0.95) setting. Allow time for the tape or paint

to reach the same temperature as the surface beneath it and then

measure the temperature of the tape or painted surface.

If you cannot paint or use tape, then you can compensate your

measurements with the emissivity selector. Even with the adjustable

emissivity, it can be difficult to get a completely accurate infrared

measurement of a target with a shiny or metallic surface. Experimentation

may be required to benchmark temperatures, and experience will help

you choose the best setting for specific measurements.

The imaging thermometer has emissivity adjustable from 0.1 to 1.0

in increments of 0.01. Refer to the Emissivity Table Value table

in this manual. The reference to emissivity settings in the table are

suggestions for typical situations and your particular situation may

differ.

NOTE: Calibration of this product was performed at 0.95 emissivity.

13

English

NOMINAL EMISSIVITY VALUE

MATERIAL VALUE MATERIAL VALUE

Carbon-filled surface 0.98 Copper, heavily oxidized 0.78

Frost crystals 0.98 Cloth, cotton 0.77

Human skin 0.98 Sand 0.76

Slate 0.97 Silica, unglazed 0.75

Water, distilled 0.96 Iron, oxidized at 100˚C 0.74

Ice, smooth 0.96 Coating No. C20A 0.73

Soil, saturated with water 0.95 Basalt 0.72

Carbon candle soot 0.95 Carbon, graphitized at

500˚C

0.71

Glass, polished plate 0.94 Red Rust 0.70

Paint, oil 0.94 Iron sheet, heavily rusted 0.69

Brick, red 0.93 Water 0.67

Paper, white bond 0.93 Black loam 0.66

Concrete 0.92 Cement, white 0.65

Soil, dry 0.92 Iron cast, oxidized 0.64

Plaster, rough coat 0.91 Lead, oxidized at 1100˚C 0.63

Wood, planed oak 0.90 Zirconia on inconel 0.62

Earthenware, glazed 0.90 Cu-Zn, brass oxidized 0.61

Snow, granular 0.89 Inconel sheet at 760˚C 0.58

Silica, glazed 0.88 Marble, smooth white 0.56

Cuprous Oxide at 38˚C 0.87 All anodized chromic acid 0.55

Emery Corundum 0.86 Iron cast, polished 0.21

Snow 0.85 Brass, rubbed 80 grit emery 0.20

Stainless, oxidized at

800˚C

0.85 Stainless steel, 18-8 buffed 0.16

Iron, oxidized at 500˚C 0.84 Aluminium as received 0.09

Cuprous Oxide at 260˚C 0.83 Steel, polished 0.07

Snow, fine particles 0.82 Aluminium, polished sheet 0.05

Brass, unoxidized 0.81 Copper, polished 0.05

Glass, convex D 0.80 Brass, highly polished 0.03

Steel, oxidized 0.79

To Change Emissivity

1. Press the menu/power button (L).

2. Press the forward (J) or back (H) arrow to highlight the emissivity

option in the menu.

3. Press the select button (I) to confirm selection.

4. Press the forward (J) or back (H) arrow to adjust the emissivity

setting. The emissivity can be adjusted in increments of 0.01 from

0.10 to 1.00.

5. Press the select button (I) to confirm the emissivity setting.

6. After saving the emissivity setting, the imaging thermometer will

automatically return to the main menu screen.

Background Temperature

For more accurate temperature measurements, it is recommended

to set the background (or reflected temperature). This is especially

important when the object being measured is at a significantly different

temperature than ambient or if the object being measured has a low

emissivity.

Setting the background temperature will help compensate for the

radiation from the surroundings.

14

English

To Change Background Temperature

1. Press the menu/power button (L).

2. Press the forward (J) or back (H) arrow to highlight the

background temperature option in the menu.

3. Press the select button (I) to confirm selection.

4 Press the forward (J) or back (H) arrow to adjust the background

temperature. The background temperature can be adjusted in

1degree increments.

5. Press the select button (I) to confirm the background

temperature setting.

6. After saving the background temperature setting, the imaging

thermometer will automatically return to the main menu screen.

To Change Color Palette

1. Press the menu/power button (L).

2. Press the forward (J) or back (H) arrow to highlight the color

palette option in the menu.

3. Press the select button (I) to confirm selection.

4. Press the forward (J) or back (H) arrow to scroll through the color

palette options. The five palette choices include: Ironbow, White

Hot, Black Hot, Rainbow and High Contrast.

5. Press the select button (I) to confirm the color palette setting.

6. After saving the color palette setting, the imaging thermometer

will automatically return to the main menu screen.

To Change the Tracking Setting

When the tracking feature is on, the imaging thermometer will locate

the hottest (red o) and coldest (blue o) spot in the displayed area. The

imaging thermometer can be moved to align the center measurement

spot (+) to the desired location.

NOTE: The displayed temperature always corresponds to the

center(+).

1. Press the menu/power button (L).

2. Press the forward (J) or back (H) arrow to highlight the tracking

option in the menu.

15

English

3. Press the select button (I) to confirm selection.

4. Press the forward (J) or back (H) arrow to turn on or off the

tracking feature.

5. Press the select button (I) to confirm the tracking feature setting.

6. After saving the tracking feature setting, the imaging thermometer

will automatically return to the main menu screen.

To Set Date and Time

1. Press the menu/power button (L).

2. Press the forward (J) or back (H) arrow to highlight the date and

time option in the menu.

3. Press the select button (I) to confirm selection.

4. Press the forward (J) or back (H) arrow to highlight the field to

change.

5. Press the select button (I) to activate the field. The field will turn

green.

6. Press the forward (J) or back (H) arrow to change the activated

field.

7. Press the select button (I) to save the changes.

8. Repeat the steps above to change the remaining fields.

9. Press the menu/power button (L) to exit.

To View Information

1. Press the menu/power button (L).

16

English

2. Press the forward (J) or back (H) arrow to highlight the information

option in the menu.

3. Press the select button (I) to confirm selection

4. The imaging thermometer will display the software version.

5. Press the menu/power button (L) to exit.

To Change Temperature Scales

1. Press the menu/power button (L).

2. Press the forward (J) or back (H) arrow to highlight the C / F option

in the menu.

3. Press the select button (I) to confirm selection

4. Press the forward (J) or back (H) arrow to highlight either C or F.

5. Press the select button (I) to confirm selection.

6. After saving the temperature scale setting, the imaging

thermometer will automatically return to the main menu screen.

Return to the Main Viewing Screen

1. Press the menu/power button (L).

2. Press the forward (J) or back (H) arrow to highlight the home

option in the menu.

3. Press the select button (I) to confirm selection.

To Download Images to Computer

The imaging thermometer records both the thermal and visual image

for each saved photo. Images are saved in bitmap format.

The micro SD card can be transferred to a computer to view the

images.

Report Writing Software

The imaging thermometer includes report writing software with your

purchase. You can also download the software from www.dewalt.

com.

17

English

To Turn Off Imaging Thermometer

1. To turn off the imaging thermometer, push the menu/power

button (L) and hold for 3 seconds. The imaging thermometer will

also automatically turn off after 10 minutes of non-use.

2. Slide lens cover (G) up to protect lens when not in use.

Operating Tips

• Use only DEWALT 12V Max* lithium-ion battery.

• Ensure the D

EWALT battery is in good working condition. If the

battery fuel gauge on the screen is empty, the battery needs to be

recharged.

Avoid sudden changes in temperature such as when entering or

leaving a heated building on a cold day as this can cause condensation

inside the imaging thermometer. To prevent condensation, place the

imaging thermometer in the kitbox or a plastic bag before exposing it

to sudden changes in temperature.

MAINTENANCE

Cleaning

WARNING: Blow dirt and dust off with clean, dry air at least once

a week. To minimize the risk of eye injury, always wear ANSI Z87.1

approved eye protection when performing this.

WARNING: Do not apply solvents to the lens as this may cause

damage. Do not clean the infrared lens too vigorously as this can

damage the delicate anti-reflective coating.

WARNING: Never use solvents or other harsh chemicals for

cleaning the non-metallic parts of the tool. These chemicals may

weaken the plastic materials used in these parts. Use a cloth

dampened only with water and mild soap. Never let any liquid get

inside the tool; never immerse any part of the tool into a liquid.

CHARGER CLEANING INSTRUCTIONS

WARNING: Shock hazard. Disconnect the charger from the AC

outlet before cleaning. Dirt and grease may be removed from the

exterior of the charger using a cloth or soft non-metallic brush. Do

not use water or any cleaning solutions.

Troubleshooting

• Make sure the lens cover (G) is open.

• Make sure the 12V Max* lithium-ion battery is charged.

• Make sure the battery is installed on the handle set when in use.

• If the screen freezes, remove the 12V Max* lithium-ion battery to

reset the unit. Reinsert the battery pack and press the power on

button.

KEY NOTES IF HAVING TROUBLE TAKING MEASUREMENT

1. Make sure to apply masking tape or flat black paint to surfaces

that are highly reflective (use the default 0.95 emissivity setting).

2. Make sure to have the correct emissivity for the material you

are testing. Refer to the Emissivity section and the Nominal

Emissivity Value table in this manual.

3. Clean the material before testing if there is heavy dirt, grease, etc.

Accessories

WARNING: Since accessories, other than those offered by

D

EWALT, have not been tested with this product, use of such

accessories with this tool could be hazardous. To reduce the risk of

injury, only D

EWALT recommended accessories should be used with

this product.

Recommended accessories for use with your tool are available

at extra cost from your local dealer or authorized service center.

If you need assistance in locating any accessory, please contact

D

EWALT Industrial Tool Co., 701 East Joppa Road, Baltimore, MD

21286, call 1-800-4-D

EWALT (1-800-433-9258) or visit our website

www.dewalt.com.

18

English

Please contact DEWALT Industrial Tool Co., 701 East Joppa Road,

Baltimore, MD 21286, call 1-800-4-D

EWALT (1-800-433-9258) or visit

our website www.dewalt.com.

Repairs

The charger and battery pack are not serviceable. There are no

serviceable parts inside the charger or battery pack.

To assure product SAFETY and RELIABILITY, repairs, maintenance

and adjustment should be performed by a D

EWALT factory service

center, a D

EWALT authorized service center or other qualified service

personnel. Always use identical replacement parts.

Register Online

Thank you for your purchase. Register your product now for:

• WARRANTY SERVICE: Registering your product will help you

obtain more efficient warranty service in case there is a problem

with your product.

• CONFIRMATION OF OWNERSHIP: In case of an insurance

loss, such as fire, flood or theft, your registration of ownership will

serve as your proof of purchase.

• FOR YOUR SAFETY: Registering your product will allow us to

contact you in the unlikely event a safety notification is required

under the Federal Consumer Safety Act.

Register online at www.dewalt.com/register.

Three Year Limited Warranty

DEWALT will repair, without charge, any defects due to faulty materials

or workmanship for three years from the date of purchase. This

warranty does not cover part failure due to normal wear or tool abuse.

For further detail of warranty coverage and warranty repair information,

visit www.dewalt.com or call 1-800-4-D

EWALT (1-800-433-9258).

This warranty does not apply to accessories or damage caused where

repairs have been made or attempted by others. This warranty gives

you specific legal rights and you may have other rights which vary in

certain states or provinces.

In addition to the warranty, D

EWALT tools are covered by our:

1 YEAR FREE SERVICE

D

EWALT will maintain the tool and replace worn parts caused by

normal use, for free, any time during the first year after purchase.

2 YEARS FREE SERVICE ON D

EWALT BATTERY PACKS

DC9071, DC9091, DC9096, DC9280, DC9360, DC9180, DCB120,

DCB201, DCB203, DCB207 and DCB127

3 YEARS FREE SERVICE ON D

EWALT BATTERY PACKS

DCB200, DCB204

D

EWALT BATTERY PACKS

Product warranty voided if the battery pack is tampered with in any

way. D

EWALT is not responsible for any injury caused by tampering

and may prosecute warranty fraud to the fullest extent permitted by

law.

90 DAY MONEY BACK GUARANTEE

If you are not completely satisfied with the performance of your

DEWALT Power Tool, Laser, or Nailer for any reason, you can return it

within 90 days from the date of purchase with a receipt for a full refund

– no questions asked.

LATIN AMERICA: This warranty does not apply to products sold

in Latin America. For products sold in Latin America, see country

specific warranty information contained in the packaging, call the local

company or see website for warranty information.

FREE WARNING LABEL REPLACEMENT: If your warning labels

become illegible or are missing, call 1-800-4-D

EWALT (1-800-433-

9258) for a free replacement.

La page est en cours de chargement...

DeWalt DCT416S1 Manuel utilisateur

DeWalt DCT416S1 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents