Bolens 31AS32AD565 Le manuel du propriétaire

Marque: Bolens

Modèle: 31AS32AD565

Catégorie: Souffleuses à neige

Taper: Le manuel du propriétaire

P. O. Box 1386, 97 KENT AVENUE, KITCHENER, ON N2G 4J1

Printed In USA

OPERATOR’S MANUAL

Safe Operation Practices • Set-Up • Operation • Maintenance • Service • Troubleshooting • Warranty

WARNING

READ AND FOLLOW ALL SAFETY RULES AND INSTRUCTIONS IN THIS MANUAL

BEFORE ATTEMPTING TO OPERATE THIS MACHINE.

FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT IN PERSONAL INJURY.

769-07158A

6.10.15

Two-Stage Snow Thrower — 300 Series

Customer Support

Please do

NOT

return the unit to the retailer from which it was purchased, without first contacting Customer Support.

If you have difficulty assembling this product or have any questions regarding the controls, operation, or maintenance of

this machine, you can seek help from the experts. Choose from the options below:

◊ Visit our web at www.mtdcanada.ca

◊ Locate your nearest dealer from Customer Support: 1-800-668-1238

◊ Contact MTD CANADA • P.O. Box 1386 • 97 Kent Avenue • Kitchener, Ontario, Canada • N2G 4J1

To The Owner

Safe Operation Practices ........................................ 3

Assembly & Set-Up .................................................. 7

Controls ...................................................................10

Operation ................................................................ 12

Maintenance & Adjustment .................................13

Service .....................................................................15

Troubleshooting .....................................................17

Replacement Parts .................................................18

Warranty .................................................................19

Table of Contents

Thank you for purchasing your new equipment. It was carefully

engineered to provide excellent performance when properly

operated and maintained.

Please read this entire manual prior to operating the equipment.

It instructs you how to safely and easily set up, operate and

maintain your machine. Please be sure that you, and any other

persons who will operate the machine, carefully follow the

recommended safety practices at all times. Failure to do so could

result in personal injury or property damage.

All information in this manual is relative to the most recent

product information available at the time of printing. Review

this manual frequently to familiarize yourself with the machine,

its features and operation. Please be aware that this Operator’s

Manual may cover a range of product specifications for

various models. Characteristics and features discussed and/or

illustrated in this manual may not be applicable to all models.

The manufacturer reserves the right to change product

specifications, designs and equipment without notice and

without incurring obligation.

If you have any problems or questions concerning the machine,

phone your local service dealer or contact us directly. Customer

Support telephone numbers, website address and mailing

address can be found on this page. We want to ensure your

complete satisfaction at all times.

Throughout this manual, all references to right and left side of the

machine are observed from the operating position.

The engine manufacturer is responsible for all engine-related

issues with regards to performance, power-rating, specifications,

warranty and service. Please refer to the engine manufacturer’s

Owner’s/Operator’s Manual, packed separately with your

machine, for more information.

Thank You

Record Product Information

Before setting up and operating your new equipment, please

locate the model plate on the equipment and record the

information in the provided area to the right. You can locate the

model plate by standing at the operator’s position and looking

down at the rear of the frame. This information will be necessary,

should you seek technical support via our web site, Customer

Support Department, or with a local authorized service dealer.

Model NuMber

Serial NuMber

Important Safe Operation Practices

Training

1. Read, understand, and follow all instructions on the

machine and in the manual(s) before attempting to

assemble and operate. Keep this manual in a safe place for

future and regular reference and for ordering replacement

parts.

2. Be familiar with all controls and their proper operation.

Know how to stop the machine and disengage them

quickly.

3. Never allow children under 14 years of age to operate this

machine. Children 14 and over should read and understand

the instructions and safe operation practices in this manual

and on the machine and be trained and supervised by an

adult.

4. Never allow adults to operate this machine without proper

instruction.

5. Thrown objects can cause serious personal injury. Plan

your snow-throwing pattern to avoid discharge of material

toward roads, bystanders and the like.

6. Keep bystanders, pets and children at least 75 feet from the

machine while it is in operation. Stop machine if anyone

enters the area.

7. Exercise caution to avoid slipping or falling, especially

when operating in reverse.

Preparation

Thoroughly inspect the area where the equipment is to be used.

Remove all doormats, newspapers, sleds, boards, wires and other

foreign objects, which could be tripped over or thrown by the

auger/impeller.

1. Always wear safety glasses or eye shields during operation

and while performing an adjustment or repair to protect

your eyes. Thrown objects which ricochet can cause serious

injury to the eyes.

2. Do not operate without wearing adequate winter outer

garments. Do not wear jewelry, long scarves or other loose

clothing, which could become entangled in moving parts.

Wear footwear which will improve footing on slippery

surfaces.

3. Use a grounded three-wire extension cord and receptacle

for all machines with electric start engines.

4. Adjust auger housing height to clear gravel or crushed rock

surfaces.

5. Disengage all control levers before starting the engine.

6. Never attempt to make any adjustments while engine is

running, except where specifically recommended in the

operator’s manual.

7. Let engine and machine adjust to outdoor temperature

before starting to clear snow.

WARNING! This symbol points out important safety instructions which, if not followed,

could endanger the personal safety and/or property of yourself and others. Read and follow

all instructions in this manual before attempting to operate this machine. Failure to comply

with these instructions may result in personal injury.

When you see this symbol. HEED ITS WARNING!

DANGER: This machine was built to be operated according to the safe operation practices in

this manual. As with any type of power equipment, carelessness or error on the part of the

operator can result in serious injury. This machine is capable of amputating fingers, hands,

toes and feet and throwing foreign objects. Failure to observe the following safety

instructions could result in serious injury or death.

CALIFORNIA PROPOSITION 65

WARNING! Engine Exhaust, some of its constituents, and certain vehicle components

contain or emit chemicals known to State of California to cause cancer and birth defects

or other reproductive harm.

4 Section 2 — important Safe operation practiceS

Safe Handling of Gasoline

To avoid personal injury or property damage use extreme care

in handling gasoline. Gasoline is extremely flammable and the

vapors are explosive. Serious personal injury can occur when

gasoline is spilled on yourself or your clothes which can ignite.

Wash your skin and change clothes immediately.

a. Use only an approved gasoline container.

b. Extinguish all cigarettes, cigars, pipes and other

sources of ignition.

c. Never fuel machine indoors.

d. Never remove gas cap or add fuel while the engine is

hot or running.

e. Allow engine to cool at least two minutes before

refueling.

f. Never over fill fuel tank. Fill tank to no more than ½

inch below bottom of filler neck to provide space for

fuel expansion.

g. Replace gasoline cap and tighten securely.

h. If gasoline is spilled, wipe it off the engine and

equipment. Move machine to another area. Wait 5

minutes before starting the engine.

i. Never store the machine or fuel container inside

where there is an open flame, spark or pilot light

(e.g. furnace, water heater, space heater, clothes

dryer etc.).

j. Allow machine to cool at least 5 minutes before

storing.

k. Never fill containers inside a vehicle or on a truck

or trailer bed with a plastic liner. Always place

containers on the ground away from your vehicle

before filling.

l. If possible, remove gas-powered equipment from

the truck or trailer and refuel it on the ground. If this

is not possible, then refuel such equipment on a

trailer with a portable container, rather than from a

gasoline dispenser nozzle.

m. Keep the nozzle in contact with the rim of the fuel

tank or container opening at all times until fueling is

complete. Do not use a nozzle lock-open device.

Operation

1. Do not put hands or feet near rotating parts, in the auger/

impeller housing or chute assembly. Contact with the

rotating parts can amputate hands and feet.

2. The auger/impeller control lever is a safety device. Never

bypass its operation. Doing so makes the machine unsafe

and may cause personal injury.

3. The control levers must operate easily in both directions

and automatically return to the disengaged position when

released.

4. Never operate with a missing or damaged chute assembly.

Keep all safety devices in place and working.

5. Never run an engine indoors or in a poorly ventilated area.

Engine exhaust contains carbon monoxide, an odorless

and deadly gas.

6. Do not operate machine while under the influence of

alcohol or drugs.

7. Muffler and engine become hot and can cause a burn. Do

not touch. Keep children away.

8. Exercise extreme caution when operating on or crossing

gravel surfaces. Stay alert for hidden hazards or traffic.

9. Exercise caution when changing direction and while

operating on slopes. Do not operate on steep slopes.

10. Plan your snow-throwing pattern to avoid discharge

towards windows, walls, cars etc. Thus, avoiding possible

property damage or personal injury caused by a ricochet.

11. Never direct discharge at children, bystanders and pets or

allow anyone in front of the machine.

12. Do not overload machine capacity by attempting to clear

snow at too fast of a rate.

13. Never operate this machine without good visibility or light.

Always be sure of your footing and keep a firm hold on the

handles. Walk, never run.

14. Disengage power to the auger/impeller when transporting

or not in use.

15. Never operate machine at high transport speeds on

slippery surfaces. Look down and behind and use care

when backing up.

16. If the machine should start to vibrate abnormally, stop

the engine, disconnect the spark plug wire and ground it

against the engine. Inspect thoroughly for damage. Repair

any damage before starting and operating.

17. Disengage all control levers and stop engine before you

leave the operating position (behind the handles). Wait

until the auger/impeller comes to a complete stop before

unclogging the chute assembly, making any adjustments,

or inspections.

18. Never put your hand in the discharge or collector openings.

Always use the clean-out tool provided to unclog the

discharge opening. Do not unclog chute assembly while

engine is running. Shut off engine and remain behind

handles until all moving parts have stopped before

unclogging.

19. Use only attachments and accessories approved by the

manufacturer (e.g. wheel weights, tire chains, cabs etc.).

20. When starting engine, pull cord slowly until resistance

is felt, then pull rapidly. Rapid retraction of starter cord

(kickback) will pull hand and arm toward engine faster than

you can let go. Broken bones, fractures, bruises or sprains

could result.

21. If situations occur which are not covered in this manual, use

care and good judgment. Contact Customer Support for

assistance and the name of your nearest servicing dealer.

5Section 2 — important Safe operation practiceS

Clearing a Clogged Discharge Chute

Hand contact with the rotating impeller inside the discharge

chute is the most common cause of injury associated with snow

throwers. Never use your hand to clean out the discharge chute.

To clear the chute:

1. SHUT THE ENGINE OFF!

2. Wait 10 seconds to be sure the impeller blades have

stopped rotating.

3. Always use a clean-out tool, not your hands.

Maintenance & Storage

1. Never tamper with safety devices. Check their proper

operation regularly. Refer to the maintenance and

adjustment sections of this manual.

2. Before cleaning, repairing, or inspecting machine

disengage all control levers and stop the engine. Wait until

the auger/impeller come to a complete stop. Disconnect

the spark plug wire and ground against the engine to

prevent unintended starting.

3. Check bolts and screws for proper tightness at frequent

intervals to keep the machine in safe working condition.

Also, visually inspect machine for any damage.

4. Do not change the engine governor setting or over-speed

the engine. The governor controls the maximum safe

operating speed of the engine.

5. Snow thrower shave plates and skid shoes are subject to

wear and damage. For your safety protection, frequently

check all components and replace with original equipment

manufacturer’s (OEM) parts only. “Use of parts which do

not meet the original equipment specifications may lead to

improper performance and compromise safety!”

6. Check control levers periodically to verify they engage

and disengage properly and adjust, if necessary. Refer

to the adjustment section in this operator’s manual for

instructions.

7. Maintain or replace safety and instruction labels, as

necessary.

8. Observe proper disposal laws and regulations for gas, oil,

etc. to protect the environment.

9. Prior to storing, run machine a few minutes to clear snow

from machine and prevent freeze up of auger/impeller.

10. Never store the machine or fuel container inside where

there is an open flame, spark or pilot light such as a water

heater, furnace, clothes dryer etc.

11. Always refer to the operator’s manual for proper

instructions on off-season storage.

12. Check fuel line, tank, cap, and fittings frequently for cracks

or leaks. Replace if necessary.

13. Do not crank engine with spark plug removed.

14. According to the Consumer Products Safety Commission

(CPSC) and the U.S. Environmental Protection Agency (EPA),

this product has an Average Useful Life of seven (7) years,

or 60 hours of operation. At the end of the Average Useful

Life have the machine inspected annually by an authorized

service dealer to ensure that all mechanical and safety

systems are working properly and not worn excessively.

Failure to do so can result in accidents, injuries or death.

Do not modify engine

To avoid serious injury or death, do not modify engine in any

way. Tampering with the governor setting can lead to a runaway

engine and cause it to operate at unsafe speeds. Never tamper

with factory setting of engine governor.

Notice Regarding Emissions

Engines which are certified to comply with California and federal

EPA emission regulations for SORE (Small Off Road Equipment)

are certified to operate on regular unleaded gasoline, and

may include the following emission control systems: Engine

Modification (EM), Oxidizing Catalyst (OC), Secondary Air

Injection (SAI) and Three Way Catalyst (TWC) if so equipped.

Spark Arrestor

WARNING! This machine is equipped with an

internal combustion engine and should not be used

on or near any unimproved forest-covered, brush

covered or grass-covered land unless the engine’s

exhaust system is equipped with a spark arrester

meeting applicable local or state laws (if any).

If a spark arrestor is used, it should be maintained in effective

working order by the operator.

A spark arrestor for the muffler is available through your nearest

engine authorized service dealer.

6 Section 2 — important Safe operation practiceS

Safety Symbols

This page depicts and describes safety symbols that may appear on this product. Read, understand, and follow all instructions on the

machine before attempting to assemble and operate.

Symbol Description

READ THE OPERATOR’S MANUAL(S)

Read, understand, and follow all instructions in the manual(s) before attempting to

assemble and operate

WARNING— WEAR EYE AND HEARING PROTECTION

Thrown objects and loud noise can cause severe eye injury and hearing loss. Wear ear

protection meeting ANSI Z87.1 standards and ear protection when operating this machine.

WARNING— ROTATING BLADES

Keep hands out of inlet and discharge openings while machine is running. There are rotating

blades inside

WARNING— ROTATING AUGER

Do not put hands or feet near rotating parts, in the auger/impeller housing or chute

assembly. Contact with the rotating parts can amputate hands and feet.

WARNING— KEEP BYSTANDERS AWAY

Keep all bystanders, especially children, away from the operating area.

WARNING—THROWN OBJECTS

This machine may pick up and throw objects which can cause serious personal injury.

WARNING—GASOLINE IS FLAMMABLE

Allow the engine to cool at least two minutes before refueling.

WARNING— CARBON MONOXIDE

Never run an engine indoors or in a poorly ventilated area. Engine exhaust contains carbon

monoxide, an odorless and deadly gas.

WARNING— ELECTRICAL SHOCK

Do not use the engine’s electric starter in the rain

WARNING— HOT SURFACE

Engine parts, especially the muffler, become extremely hot during operation. Allow engine

and muffler to cool before touching.

WARNING! Your Responsibility—Restrict the use of this power machine to persons who read, understand and

follow the warnings and instructions in this manual and on the machine.

SAVE THESE INSTRUCTIONS!

Assembly & Set-Up

Assembly

NOTE: Remove all loose parts and any packing material before

assembling.

Setting Up The Handle

1. Cut and remove the cable tie (if present) securing upper

handle to lower handle.

NOTE: Be aware of the three loosely fitted cable ties attached to

the lower handle that will be utilized later to secure the cables.

NOTE: Do not lift the snow thrower by the chute handle.

2. Loosen and remove the wing knob, saddle washer, handle

tab and carriage bolt on each side of the lower handle. See

Figure 3-1.

3. Slide the loosely fitted cable tie from the right side of the

lower handle up to the cross member of the lower handle.

Leave the second cable tie in place on the right side of the

lower handle with the mounting post pushed into the hole

on the handle. See Fig. 3-3 for reference.

IMPORTANT: It will be necessary to lift the upper handle while

sliding up this cable tie to prevent damage to the cable.

4. Lift the upper handle up and position it over the lower

handle, aligning the holes where the wing knobs were

removed (1). See Fig. 3-2.

CAUTION: Be careful not to bend or kink the cables.

5. Insert a carriage screw from the outside through a handle

tab, the upper and lower handles, a saddle washer and into

the wing knob (2). Repeat on the other side.

6. Tighten the wing knobs on each side of the handle. Refer to

Fig. 3-2.

NOTE: The auger cable routes down the left lower handle

and the drive cable is routed across the top of the lower

handle and down the right side of the lower handle. See

Fig. 3-3.

7. Tighten the cable ties on the lower handle in the positions

shown in Fig. 3-3. Trim off excess material of cable ties.

Figure 3-1

Figure 3-3

Figure 3-2

Drive Cable

Auger Cable

8 Section 3 — ASSembly & Set-Up

Tire Pressure

WARNING: Under any circumstance do not exceed

manufacturer’s recommended psi. Equal tire

pressure should be maintained at all times. Excessive

pressure when seating beads may cause tire/rim

assembly to burst with force sufficient to cause

serious injury. Refer to sidewall of tire for

recommended pressure.

The tires are over-inflated for shipping purposes. Check the tire

pressure before operating the snow thrower. Refer to the tire

side wall for tire manufacturer’s recommended psi and deflate

(or inflate) the tires as necessary. Use a manual pump or portable

electric tire inflator to prevent over-inflation.

NEVER USE AN AIR COMPRESSOR

Adjustments

Skid Shoe

The snow thrower skid shoes are adjusted upward at the factory

for shipping purposes. Adjust them downward, if desired, prior

to operating the snow thrower.

CAUTION : It is not recommended that you operate

this snow thrower on gravel as it can easily pick up

and throw loose gravel, causing personal injury or

damage to the snow thrower and surrounding

property.

• For close snow removal on a smooth surface, raise skid

shoes higher on the auger housing.

• Use a middle or lower position when the area to be cleared

is uneven, such as a gravel driveway

NOTE: If you choose to operate the snow thrower on a gravel

surface, keep the skid shoes in position for maximum clearance

between the ground and the shave plate.

CAUTION: Operating a snow thrower equipped

with steel skid shoes may result in damage to

natural stone paver surfaces (e.g. sandstone,

bluestone, limestone). Refer to the Replacement

Parts sections for information on available polymer

skid shoes.

To adjust the skid shoes:

1. Loosen the four hex nuts (two on each side) and carriage

bolts. Move skid shoes to desired position. See Fig. 3-6.

2. Make certain the entire bottom surface of skid shoe is

against the ground to avoid uneven wear on the skid shoes.

3. Retighten nuts and bolts securely.

Set-Up

Shear Pins

Replacement shear pins and cotter pins are provided for your

convenience. Store these safely until needed.

Chute Clean-Out Tool

The chute clean-out tool is fastened to the top of the auger

housing with a mounting clip and a cable tie at the factory. Cut

the cable tie before operating the snow thrower. See Fig. 3-5.

Figure 3-4

Figure 3-5

Chute Clean-out Tool

9Section 3 — ASSembly & Set-Up

Auger Control

Periodic adjustment to the auger control cable may be required

due to normal stretch and wear on the belt. Adjustment is

needed immediately if the augers:

a. Continue to turn with the auger control disengaged, or

b. During operation, augers seem to hesitate turning

while the engine maintains speed.

NOTE: Perform the following test before operating the snow

thrower for the first time and at the start of each winter season.

Check the adjustment of the auger control as follows:

1. When the auger control is released and in the disengaged

“up” position, the cable should have very little slack, but

should NOT be tight.

2. In a well-ventilated area, start the snow thrower engine as

instructed in the engine manual. Make sure the throttle is set

in the FAST position.

3. While standing in the operator’s position (behind the snow

thrower) engage the auger.

4. Allow the auger to remain engaged for approximately 10

seconds before releasing the auger control. Repeat this

several times.

5. With the engine running in the FAST position and the

auger control in the disengaged “up” position, walk to the

front of the machine.

6. Confirm that the auger has completely stopped rotating

and shows NO signs of motion.

NOTE: If the auger shows ANY signs of rotating, immediately

return to the operator’s position and shut off the engine. Wait for

all moving parts to stop before adjusting the auger control cable

as follows:

7. Loosen the rear hex screw on the cable adjustment bracket.

See Fig. 3-8.

8. Slide the cable adjustment bracket forward adding a slight

amount of slack in the auger cable.

9. Retighten the rear hex screw.

10. Start engine and verify auger control engages and

disengages properly.

NOTE: If auger continues to rotate with the control

disengaged, shut off engine and readjust.

11. If during operation, augers seem to hesitate turning while

the engine maintains speed, then the cable is too loose and

the bracket needs to be adjusted rearward, decreasing the

amount of slack to the auger cable. Follow the above steps

to adjust the cable adjustment bracket.

WARNING! Do not over-tighten the cable.

Overtightening may prevent the auger from

disengaging and compromise the safety of the snow

thrower.

Figure 3-7

Figure 3-8

Figure 3-6

Controls and Features

Snow thrower controls and features are described below and

illustrated in Fig. 4-1.

Drive Control

Located on the underside of the upper handle, the drive control

is used to engage/disengage wheels. Squeeze the drive control

against the upper handle to engage the wheels; release to

disengage.

Auger

When engaged, the auger’s rotation draw snow into the auger

housing and throws it out the discharge chute.

Chute Assembly

The direction snow is thrown can be changed by turning the

lower chute with the chute handle. The distance snow is thrown

can be adjusted by raising the upper chute for greater distance,

or lowering for less distance. Loosen the wing nut on the side of

the discharge chute to adjust. Pivot the chute to desired position,

and retighten wing nut.

Auger Control

The auger control is adjacent to the upper handle. Squeeze the

auger control against the upper handle to engage the augers;

release to disengage the augers.

IMPORTANT: Refer to the Auger Control information in

the Assembly & Set-Up section prior to operating your snow

thrower. Read and follow all instructions carefully and perform all

adjustments to verify your snow thrower is operating safely and

properly.

Shave Plate

The shave plate maintains contact with pavement as the snow

thrower is propelled, allowing snow close to pavement’s surface

to be discharged.

Skid Shoes

Position the skid shoes based on surface conditions. Adjust

upward for hard-packed snow. Adjust downward when

operating on gravel or crushed rock surfaces.

Figure 4-1

Chute Assembly

Clean-out Tool

Auger

Shave Plate

Skid Shoe

Chute Handle

Auger Control

Upper Handle

Drive

Control

Chute Assembly

Clean-out Tool

Auger

Shave Plate

Skid Shoe

Chute Handle

Auger Control

Upper Handle

Drive

Control

Chute Assembly

Clean-out Tool

Auger

Shave Plate

Skid Shoe

Chute Handle

Auger Control

Upper Handle

Drive

Control

11Section 4 — controlS and FeatureS

Chute Clean-Out Tool

WARNING! Never use your hands to clear a

clogged chute assembly. Shut off engine and remain

behind handles until all moving parts have stopped

before unclogging.

The chute clean-out tool is conveniently fastened to the rear of

the auger housing with a mounting clip. Should snow and ice

become lodged in the chute assembly during operation, proceed

as follows to safely clean the chute assembly and chute opening:

1. Release both the Auger Control and the Drive Control.

2. Shut off engine as instructed in the engine manual.

3. Remove the clean-out tool from the clip which secures it to

the rear of the auger housing.

4. Use the shovel-shaped end of the clean-out tool to

dislodge and scoop any snow and ice which has formed in

and near the chute assembly.

5. Refasten the clean-out tool to the mounting clip on the

rear of the auger housing, start the snow thrower’s engine

as instructed in the engine manual.

While standing in the operator’s position (behind the snow

thrower), engage the auger control for a few seconds to clear any

remaining snow and ice from the chute assembly.

Starting and Stopping the Engine

Refer to the Engine Operator’s Manual packed with your snow

thrower for instructions on starting and stopping the engine.

To Engage Drive

1. Move the throttle control into the Fast (rabbit) position.

2. To engage the drive, squeeze the drive control completely

against the upper handle to engage the wheels. To stop

the forward motion, release the drive control.

To Engage Augers

1. To engage the augers, squeeze the auger control handle

completely against the upper handle. To stop the augers,

release handle.

Replacing Shear Pins

The augers are secured to the spiral shaft with two shear pins

and cotter pins. If the auger should strike a foreign object or ice

jam, the snow thrower is designed so that the pins may shear. If

the augers will not turn, check to see if the pins have sheared.

See Fig. 5-1.

CAUTION: NEVER replace the auger shear pins

with anything other than OEM Part No. 738-04124A

replacement shear pins. Any damage to the auger

gearbox or other components as a result of failing to

do so will NOT be covered by your snow thrower’s

warranty.

WARNING! Always turn off the snow thrower’s

engine, as instructed in the engine owner’s manual

and remove the key prior to replacing shear pins.

Figure 5-1

Operation

Maintenance & Adjustments

Shave Plate and Skid Shoes

The shave plate and skid shoes on the bottom of the snow

thrower are subject to wear. These should be checked

periodically and replaced when necessary.

To replace skid shoes:

1. Remove the carriage bolts and nuts securing each skid shoe

to the auger housing, See Fig. 6-1.

2. Reassemble new skid shoes with hardware just removed.

Make sure the skid shoes are adjusted to be level.

To remove shave plate:

3. Remove both skid shoes and hardware including carriage

bolts and nuts which attach shave plate to the snow

thrower housing. For location of shave plate, see Fig. 6-1.

4. Reassemble new shave plate, making sure heads of the

carriage bolts are to the inside of the housing.

5. Reinstall skid shoes. Tighten securely.

Maintenance

General Recommendations

• Always observe safety rules when performing any type of

maintenance.

• The warranty on this snow thrower does not cover items

that have been subjected to operator abuse or negligence.

To receive full value from the warranty, operator must

maintain the snow thrower as instructed in this manual.

• Periodically check all fasteners and hardware to make sure

these are tight.

WARNING! Before servicing, repairing, lubricating,

or inspecting, disengage all controls and stop

engine. Wait until all moving parts have come to a

complete stop. Disconnect spark plug wire and

ground it against the engine to prevent unintended

starting. Always wear safety glasses during

operation or while performing any adjustments or

repairs.

Engine

IMPORTANT: Refer to the engine operator’s manual included

with the snow thrower for complete maintenance instructions.

Tire Pressure

Refer to “Assembly & Set-Up” section of this manual.

Check V-Belts

Follow instructions below to check condition of drive belt.

1. Remove the plastic belt cover on the front of the engine by

removing the self-tapping screw and pressing the plastic

tabs to release the belt cover. See Fig. 7-1 in the Service

section of this manual.

2. Visually inspect for frayed, cracked, or excessively worn out

belts. Replace, if necessary, following instructions in the

Service section of this manual.

Figure 6-1

Note: Augers not shown for clarity.

14 Section 6— Maintenance & adjuStMentS

Lubrication

1. Lubricate pivot points on the auger control and drive

control with a light engine oil once a season, see Fig. 6-2.

2. Lubricate the auger idler bracket with a light engine oil

once a season. See Fig. 6-2.

Auger Shaft

At least once a season, remove the shear pins from the auger

shaft. Spray lubricant inside the shaft and around the spacers and

the flange bearings found at either end of the shaft.

See Fig. 6-3.

Wheels

At least once a season, remove both wheels. Clean and coat the

axles with a multipurpose automotive grease before reinstalling

wheels.

Off-Season Storage

If the snow thrower will not be used for 30 days or longer, follow

the storage instructions below.

• Lubricate the machine as instructed earlier in this section.

• Store in a clean, dry area.

• If storing the snow thrower in an unventilated area,

rustproof the machine using a light oil or silicone to coat

the snow thrower.

• Clean the exterior of the engine and the snow thrower.

NOTE: Refer to the Engine Operator’s Manual for information on

storing your engine.

Figure 6-2

Figure 6-3

Se rvice

Augers

The augers are secured to the spiral shaft with four shear pins and

cotter pins. If you hit a foreign object or ice jam, the snow thrower

is designed so that the pins may shear. Refer to Fig. 5-1.

If the augers do not turn, check if the pins have sheared. Replace,

if needed, with proper shear pins. Refer to Parts List for correct

part number.

CAUTION: NEVER replace the auger shear pins

with standard pins or fasteners. Any damage to the

auger gearbox or other components, as a result of

doing so, will NOT be covered by your snow

thrower’s warranty.

Replacing Belts

1. Allow the engine to run until it is out of fuel. Do not

attempt to pour fuel from the engine

2. Remove the key to prevent accidental starting.

3. Remove the self-tapping screw shown in Fig. 7-1, and press

the plastic tabs to release the belt cover. Pull the belt cover

up and out from around the engine and chute assembly.

Set it aside and save.

Auger Belt

1. Tip the snow thrower up and forward so that it rests on

the auger housing. Remove the belt keeper (Refer to Fig.

7-3). Return the snow thrower to its upright position to

complete the following steps.

2. Slip the front auger belt off of the engine pulley, pushing it

forward and rolling in off of the pulley. See Fig. 7-2.

3. Squeeze the auger control handle to release the auger

brake, which is the tab that holds the belt onto the auger

pulley. Remove the belt.

4. Replace with new belt and reassemble in reverse order.

5. Check the adjustment of the auger control, refer to

“Assembly and Set Up” section of this manual.

Figure 7-1

Plastic Tab

Figure 7-2

Auger Belt

Belt Keeper

Idler Bracket

Drive

Belt

Engine

Pulley

Auger

Pulley

16 Section 7— Service

Drive Belt

1. Tip the snow thrower up and forward so that it rests on the

auger housing.

2. Remove the spring that connects the transmission to a bolt

on the engine frame. See Fig. 7-3.

NOTE: It may be easier to first remove the flange lock nut,

then use needle-nosed pliers to firmly grip spring and

remove from bolt.

3. Pivot the transmission forward to release pressure on the

drive belt. Remove belt from transmission pulley.

4. Remove the auger belt and drive belt from around the

engine pulley, and away from the unit.

5. Place the new drive belt on the engine pulley. See Fig. 7-2.

6. Tilt the transmission forward and position the drive belt

onto the transmission pulley.

7. Reconnect the spring to the bolt on the engine frame and

secure the transmission. Reinstall the flange lock nut.

8. Install auger belt.

9. Reassemble the belt cover on the snow thrower

10. Reassemble the belt keeper to the housing.

11. Check the adjustment of the auger control, refer to

“Assembly and Set Up” section of this manual.

Figure 7-3

Drive

Belt

Spring

Drive

Pulley

Belt Keeper

Troubleshooting

Problem Cause Remedy

Excessive vibration 1. Loose parts or damaged auger. 1. Stop engine immediately and disconnect

spark plug wire. Check for possible damage.

Tighten all bolts and nuts. Repair as needed.

If the problem persists, take unit to an

authorized service dealer.

Unit fails to self-propel 1. Drive belt loose or damaged.

2. Single speed transmission damaged.

1. Replace drive belt.

2. See an authorized dealer.

Augers continue to rotate 1. Cable out of adjustment. 1. Adjust auger control cable as shown in

“Adjusting Auger Cable” section.

Unit fails to discharge snow 1. Chute assembly clogged.

2. Shear pin(s) sheared.

3. Foreign object lodged in auger.

4. Auger control cable out of adjustment.

5. Auger belt loose or damaged.

1. Stop engine and disconnect spark plug wire.

Clean chute and inside of auger housing with

clean-out tool or stick.

2. Replace shear pin(s).

3. Stop engine immediately and disconnect the

spark plug wire. Remove object from auger.

4. Adjust auger control cable.

5. Replace auger belt.

IMPORTANT: Refer to the engine operator’s manual included with the snow thrower for engine troubleshooting instructions.

Component Part Number and Description

954-05110 Auger Drive Belt

954-04013 Wheel Drive Belt

738-04124A Shear Pin, 1.50

714-04040 Bow-tie Cotter Pin

784-5580 Skid Shoe, Standard

784-06439 Skid Shoe, Polymer (optional)

731-2643 Chute Clean-out Tool

790-00117 Shave Plate, 22”

Replacement Parts

NOTE: Download a complete Parts Manual, refer to customer support on page 2. Be sure to have your model number and serial

number ready. Refer to page 2 for more information regarding locating your model and serial numbers.

TWO YEAR LIMITED WARRANTY

The limited warranty set forth below is given by MTD Products Limited (“MTD”) with respect to new merchandise purchased and used

in Canada and/or its territories and possessions.

MTD warrants this product (excluding its normal wear parts as described below) against defects in material and workmanship for

a period of two (2) years commencing on the date of original purchase and will, at its option, repair or replace, free of charge, any

part found to be defective in materials or workmanship. This limited warranty shall only apply if this product has been operated

and maintained in accordance with the Operator’s Manual furnished with the product, and has not been subject to misuse, abuse,

commercial use, neglect, accident, improper maintenance, alteration, vandalism, theft, fire, water, or damage because of other peril or

natural disaster. Damage resulting from the installation or use of any part, accessory or attachment not approved by MTD for use with

the product(s) covered by this manual will void your warranty as to any resulting damage.

Normal wear parts are warranted to be free from defects in material and workmanship for a period of thirty (30) days from the date

of purchase. Normal wear parts include, but are not limited to items such as: batteries, belts, blades, blade adapters, grass bags, rider

deck wheels, seats, snow thrower skid shoes, friction wheels, shave plates, auger spiral rubber, tires, engine oil, air filters and spark

plugs.

HOW TO OBTAIN SERVICE: Warranty service is available, WITH PROOF OF PURCHASE, through your local authorized service dealer. To

locate the dealer in your area contact MTD Products Limited, Kitchener, ON N2G 4J1, or call 1-800-668-1238 or log on to our Web site

at www.mtdcanada.com.

This limited warranty does not provide coverage in the following cases:

a. The engine or component parts thereof. These items may carry a separate manufacturer’s warranty. Refer to applicable

manufacturer’s warranty for terms and conditions. The Powermore engine is not excluded under this agreement.

b. Log splitter pumps, valves, and cylinders have a separate one-year warranty.

c. Routine maintenance items such as lubricants, filters, blade sharpening, tune-ups, brake adjustments, clutch adjustments,

deck adjustments, and normal deterioration of the exterior finish due to use or exposure.

d. Service completed by someone other than an authorized service dealer.

e. MTD does not extend any warranty for products sold or exported outside of Canada, including possessions and

territories.

f. Replacement parts that are not genuine MTD parts.

g. Transportation charges and service calls.

h. If products are used commercially. (MTD may separately offer Limited Commercial Warranties on certain select products.

Ask your dealer or retailer for details or contact MTD Service for more information.)

No implied warranty, including any implied warranty of merchantability of fitness for a particular purpose, applies after

the applicable period of express written warranty above as to the parts as identified. No other express warranty, whether

written or oral, except as mentioned above, given by any person or entity, including a dealer or retailer, with respect to any

product, shall bind MTD. During the period of the warranty, the exclusive remedy is repair or replacement of the product as

set forth above.

The provisions as set forth in this warranty provide the sole and exclusive remedy arising from the sale. MTD shall not be

liable for incidental or consequential loss or damage including, without limitation, expenses incurred for substitute or

replacement lawn care services or for rental expenses to temporarily replace a warranted product.

Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, or limitations on how long an

implied warranty lasts, so the above exclusions or limitations may not apply to you.

In no event shall recovery of any kind be greater than the amount of the purchase price of the product sold. Alteration of safety

features of the product shall void this warranty. You assume the risk and liability for loss, damage, or injury to you and your

property and/or to others and their property arising out of the misuse or inability to use the product.

This limited warranty shall not extend to anyone other than the original purchaser or to the person for whom it was purchased as a

gift.

HOW LOCAL LAWS RELATE TO THIS WARRANTY: This limited warranty gives you specific legal rights, and you may also have other

rights that vary in different jurisdictions.

IMPORTANT: Owner must present Original Proof of Purchase to obtain warranty coverage.

MTD Products Limited, P. O. BOX 1386, KITCHENER, ON N2G 4J1; Phone: 1-800-668-1238

0 4.10.15

No tes

La page charge ...

Bolens 31AS32AD565 Le manuel du propriétaire

Marque: Bolens

Modèle: 31AS32AD565

Catégorie: Souffleuses à neige

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: Bolens 31AS32AD565 Owner's manual

Bolens 31AS32AD565 Le manuel du propriétaire

Bolens 31AS32AD565 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents