Horizon Fitness S3+ Le manuel du propriétaire

OWNER’S MANUAL

MANUEL DU PROPRIÉTAIRE

MANUAL DEL PROPIETARIO

2

3 ENGLISH

33 FRANÇAIS

63 ESPAÑOL

3

IMPORTANT PRECAUTIONS

SAVE THESE INSTRUCTIONS

When using an exercise product, basic precautions should always be followed, including the following: Read all instructions

before using this indoor cycle. It is the responsibility of the owner to ensure that all users of this indoor cycle are adequately

informed of all warnings and precautions. If you have any questions after reading this owner’s manual, contact customer

support using the contact information on the INFORMATION CARD.

3

4

WARNING

READ AND SAVE ALL INSTRUCTIONS BEFORE ASSEMBLING OR USING THIS INDOOR CYCLE.

IT IS STRONGLY RECOMMENDED TO TAKE THE FOLLOWING SAFETY INSTRUCTIONS.

• CAUTION: If you experience chest pains, nausea, dizziness or shortness of breath, stop exercising immediately and consult your physician

before continuing.

• Use this cycle for its intended purpose as described in this manual.

Do not use attachments that have not been recommended by the manufacturer.

• Never operate the cycle if it is not working properly, or if it has been damaged.

Contact Horizon Fitness or the authorized dealers for examination and repair.

• Do not use the cycle without proper footwear. NEVER operate the cycle with bare feet.

• Do not wear any clothing that might catch on any moving parts of this cycle.

• Keep hands and feet clear at all times from moving parts to avoid injury. Never turn the pedal cranks by hand.

• Do not dismount the cycle until the pedals are at a complete STOP.

• Do not attempt to ride the cycle in a standing position at high RPMs until you have practiced at slower speeds.

• Do not insert any object, hands or feet into any openings, or expose hands, arms or feet to the drive mechanism or other potentially moving

part of the cycle.

• Do not use any equipment that is damaged or has worn or broken parts. Use only replacement parts supplied by Horizon Fitness or the

authorized dealers.

• Do not operate where aerosol (spray) products are being used or when oxygen is being administered.

• Close supervision is necessary when used near children, invalids or disabled people.

• When the cycle is in use, young children and pets should be kept at least 3 meters / 10 feet away.

• After exercising, push down on the tension knob or turn the tension knob in a clockwise direction to slow the flywheel down and decrease the

potential for injury.

• Ensure that adjustment levelers (saddle and handlebar height, saddle and handlebar fore-and-aft) are properly secured and do not interfere

with range of motion during exercise.

• It is the sole responsibility of the owner to ensure that all users of the indoor cycle are informed of all warnings and precautions.

• Keep the indoor cycle indoors, away from moisture and dust. Do not place the indoor cycle in a garage, covered patio or near water.

• Place the indoor cycle on a level surface. To protect the floor or carpet from damage, place a mat beneath the indoor cycle.

• The indoor cycle does not have a independently moving flywheel; the pedals will continue to move together with the flywheel until

the flywheel stops.

5

INDOOR CYCLE OPERATION

5

6

3 ft

6 ft

3 ft

91 cm 91 cm

1 ft

183 cm

30 cm

FRONT

REAR

BIKE

HOW TO MOVE THE INDOOR CYCLE

Due to the weight of the Indoor Cycle, it is recommended

that two persons move it. While one person lifts the back

of the indoor cycle, the second person firmly holds the

handlebar and tips the indoor cycle forward until it rolls

on the wheels. Carefully move the Indoor Cycle to the

desired location and then lower it.

If the Indoor Cycle rocks on the floor after being set

down, turn the leveling feet underneath the front or rear

stabilizer until the rocking motion is eliminated.

Leveling Feet

To reduce the risk of injury, use extreme caution

while moving the indoor cycle. Do not attempt to

move it over uneven surfaces and make sure there’s

a safety space of 20 inch (minimum) to the nearest

equipment is recommended.

WARNING

LOCATION OF THE

INDOOR CYCLE

Place the Indoor Cycle on a

level surface. There should be

6 feet (183 cm) of clearance

behind the Indoor Cycle, 3 feet

(91 cm) on each side and 1 foot

(30 cm) in front of the Indoor

Cycle. Do not place the cycle

in any area that will block any

vent or air openings. The Indoor

Cycle should not be located in

a garage, covered patio, near

water or outdoors.

7

HOW TO ADJUST THE INDOOR CYCLE

The Indoor Cycle can be adjusted for maximum comfort and exercise effectiveness. The instructions below describe one

approach to adjusting the Indoor Cycle to ensure optimal user comfort and ideal body positioning; you may choose to adjust the

Indoor Cycle differently.

SADDLE ADJUSTMENT

Proper saddle height helps ensure maximum

exercise efficiency and comfort, while

reducing the risk of injury. Adjust the saddle

height to make sure it’s in proper position, one

that keeps a slightly bend in your knee while

your legs are in the extended position.

HANDLEBAR ADJUSTMENT

Proper position for the handlebar is based

primarily on comfort. Typically, the handlebar

should be positioned slightly higher than

the saddle for beginning cyclists. Advanced

cyclists could try different heights to get the

arrangement most suitable for you.

A

B

8

TO ADJUST THE SADDLE HEIGHT:

Rotate the adjustment knob counterclockwise and adjust the saddle to a comfortable pedaling position. Rotate the lever

clockwise to lock saddle position.

TO ADJUST THE SADDLE HORIZONTAL POSITION:

Rotate the adjustment knob counterclockwise to slide the saddle forward or backward as desired. Rotate the lever clockwise to

lock saddle position. Test the saddle slide for proper operation.

Do not adjust the

saddle position

beyond the stop

marks on the

saddle slider

Do not adjust

saddle height

beyond the

stop mark on

the stem

9

TO ADJUST THE HANDLEBAR HEIGHT:

Rotate the adjustment knob counterclockwise to adjust the handlebar height. Raise or lower the handlebar to the desired

height. Rotate the lever clockwise to lock handlebar position.

TO ADJUST THE PEDAL STRAPS:

Place each foot ankle on the pedal and in the toe clip that the foot ankle is centered over the pedal spindle (center of the

pedal). Rotate one foot to arms reach and pull up on the toe clip strap. Repeat for the other foot. Keep your knees over your

feet as you pedal. To remove your foot from the toe clip, loosen the strap and pull out.

Do not adjust the

handlebar height

beyond the stop

mark on the stem

The pedal straps should

be adjusted to hold the

foot snugly in the pedal.

10

TENSION CONTROL AND EMERGENCY BRAKE

The preferred level of difficulty in pedaling (resistance) can be regulated in fine increments by use of the tension control

knob. To increase the resistance, turn the tension control knob clockwise. To decrease the resistance, turn the knob counter

clockwise.

IMPORTANT:

• To stop the flywheel while pedaling, push down on the

yellow emergency brake lever.

• The flywheel should quickly come to a complete stop.

• Make sure your shoes are fixed into the toe clip.

• Apply full resistance load when the bike is not in use to

prevent injuries due to moving drive gear components.

Tension control knob

Emergency brake

The Indoor Cycle does not have a free moving flywheel; the

pedals will continue to move together with the flywheel until

the flywheel stops. Reducing speed in a controlled manner

is required. To stop the flywheel immediately, push down the

yellow emergency brake lever. Always pedal in a controlled

manner and adjust your desired cadence according to your

own abilities. Push the yellow lever down = emergency stop.

WARNING

The Indoor Cycle uses a fixed flywheel that builds momentum and will keep the pedals turning even after the user stops pedaling or if the

user’s feet slip off. DO NOT ATTEMPT TO REMOVE YOUR FEET FROM THE PEDALS OR DISMOUNT THE MACHINE UNTIL BOTH

THE PEDALS AND THE FLYWHEEL HAVE COMPLETELY STOPPED. Failure to follow these instructions may lead to loss of control and

the potential for serious injury.

WARNING

11

ASSEMBLY

There are several areas during the assembly process that special attention must be paid. It is very important to follow the

assembly instructions correctly and to make sure all parts are firmly tightened. If the assembly instructions are not followed

correctly, the indoor cycle could have parts that are not tightened and will seem loose and may cause irritating noises. To

prevent damage to the indoor cycle, the assembly instructions must be reviewed and corrective actions should be taken.

Before proceeding, find your indoor cycle’s serial number located on

the rear base frame of the cycle and enter it in the space provided below.

ENTER YOUR SERIAL NUMBER IN THE BOX BELOW:

» Refer to the SERIAL NUMBER and MODEL NAME when calling for service.

» Be sure to enter both the SERIAL NUMBER and MODEL NAME on your warranty card.

SERIAL NUMBER:

MODEL NAME:

HORIZON S3+ INDOOR CYCLE

WARNING

11

12

Saddle

Tension Control & Emergency Brake

Adjustable Knob

Speed Sensor

Console

Heavy Flywheel

Transportation Wheel

Durable Crank

Belt

Bottom Bracket

Seat Post

Seat Slider

MODEL INFORMATION

13

PRE ASSEMBLY

MAIN PARTS INCLUDED:

1 Main Frame

Front & rear stabilizer

Handlebar Set

Seat Post Set

PARTS PACKING

INCLUDED:

1 Console box

1 Parts box

1 Water bottle

1 Owners Manual

If you have questions or if there

are any missing parts, contact your

local dealer. Contact information

may be located on the back panel

of this manual or on warranty card.

UNPACKING

Due to the weight of the indoor cycle, it is recommended that two persons

perform the assembly. Set the indoor cycle in a cleared area and remove all

packing materials; do not dispose of the packing materials until assembly is

completed.

NOTE: During each assembly step, ensure that ALL nuts and bolts are in place and

partially threaded in before completely tightening any ONE bolt.

NOTE: A light application of grease may aid in the installation of hardware. Any

grease, such as lithium bike grease is recommended.

NEED HELP?

14

ASSEMBLY INSTRUCTIONS

ASSEMBLY PARTS LIST

ITEM DESCRIPTION QTY SPECIFICATION

1 Handlebar 1 Chrome & PVC dipping

2 Seat Post 1 Chrome

3 Pedal (L) 1 Left threaded

4 Pedal (R) 1 Right threaded

5

Combination

Wrench

1

6 Allen Wrench 1 for 2 stabilizes

7 Allen Bolt 4 M8 x 16L

8 Washer 4

9 Front Stabilizer 1 With 2 transportation wheels

10 Rear Stabilizer 1 Without 2 transportation wheels

11

Console, Console

Bracket and Screw

3

1

2

3

4

5

6

7

8

6

7

8

9

10

11

15

ASSEMBLY STEP 1

A Remove the TWO SHIPPING TUBES (14) from

the frame and THROW AWAY.

B Attach the FRONT STABILIZER (9) to the

frame using TWO ALLEN BOLTS (7) and TWO

WASHERS (8), and secure firmly by ALLEN

WRENCH (6).

9

8

7

6

14

16

ASSEMBLY STEP 2

A Attach the REAR STABILIZER (10) to the

frame using TWO ALLEN BOLTS (7) and TWO

WASHERS (8), and secure firmly by ALLEN

WRENCH (6).

6

10

7

8

17

ASSEMBLY STEP 3

A Thread the LEFT PEDAL (3) that has “L” on the

spindle to the left side arm of the cycle using the

COMBINATION WRENCH (5). Please note that

the L pedal is left-hand threaded which needs to be

turned COUNTER CLOCKWISE to tighten.

B Thread the RIGHT PEDAL (4) that has “R” on the

spindle to the right side arm of the cycle using the

COMBINATION WRENCH (5). Please note that the

R pedal is right-hand threaded which needs to be

turned clockwise to tighten.

3

4

5

18

ASSEMBLY STEP 4

A Carefully insert SPEED SENSOR (11) into the frame,

checking that it comes out the other side and does

not get caught.

Note: SPEED SENSOR (11) is the other end of

LOWER CONSOLE CABLE (B)

B Install the HANDLEBAR (1) into the frame receptor

and secure with the knob.

1

11

B

19

ASSEMBLY STEP 5

A Install the SEAT POST (2) into the frame receptor

and secure with the knob.

2

20

A Install the MOUNTING CLAMP (11) to the uppper

handlebar with CONSOLE SCREW (12) and adjust

the console angle.

Note: do not tighten the screw at this stage.

B Fix CONSOLE (13) with console mounting clamp

from the back.

ASSEMBLY STEP 6

13

11

12

La page charge ...

Horizon Fitness S3+ Le manuel du propriétaire

Ce manuel convient également à

Horizon Fitness S3+ Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents