Samsung PS-50Q91HR Manuel utilisateur

Register your product at www.samsung.com/global/register

Record your Model and Serial number here for future reference.

▪ Model _______________ ▪ Serial No. _______________

PDP-TELEVISION

(PLASMA DISPLAY PANEL)

PS42Q91HR PS42Q92HR

PS42C91HR PS42C92HR

PS50Q91HR PS50Q92HR

PS50C91HR PS50C92HR

Owner’s Instructions

Before operating the unit,

please read this manual thoroughly,

and retain it for future reference.

ON-SCREEN MENUS

Picture In Picture (PIP)

Energy Saving

TELETEXT (Option)

SRS TruSurround XT

Digital Natural Image engine

BN68-01294B-01

Contact SAMSUNG WORLD-WIDE

If you have any questions or comments relating to Samsung products, please contact the

SAMSUNG customer care centre.

Связывайтесь с SAMSUNG по всему миру

Если у вас есть предложения или вопросы по продуктам Samsung, связывайтесь с

информационным центром Samsung.

Country

Customer Care Centre 

Web Site

RUSSIA 8-800-200-0400 www.samsung.ru

UKRAINE 8-800-502-0000 www.samsung.com/ur

01294B-01_CIS(BWT)_E,R_Cover.indd 1 2007-10-08 ¿ÀÈÄ 3:28:09

English - 2

User Instructions

 Screen Image retention

Do not display a still image (such as on a video game or when hooking up a PC to this PDP) on the

plasma monitor panel for more than 2 hours as it can cause screen image retention. This image

retention is also known as “screen burn”. To avoid such image retention, reduce the degree of

brightness and contrast of the screen when displaying a still image.

 Height

The PDP can normally operate only under 2000m in height. It might abnormally function at a place

over 2000m in height so do not install and operate there.

 Heat on the top of the PDP TV

The top side of the product may be hot after long period of use as heat dissipates from the panel

through the vent hole in the upper part of the product. This is normal and does not indicate any defect

or operation failure of the product. However, children should be prevented from touching the upper

part of the product.

 The product is making a ‘cracking’ noise.

A ‘cracking’ noise may occur when the product contracts or expands due to a change of surrounding

environment such as temperature or humidity. This is normal and not a defect of the unit.

 Cell Defects

The PDP uses a panel consisting of 1,230,000(SD-level) to 3,150,000(HD-level) pixels which require

sophisticated technology to produce. However, there may be few bright or dark pixels on the screen.

These pixels will have no impact on the performance of the product.

 Avoid operating the TV at temperatures below 5°C(41°F)

 A still image displayed too long may cause permanent damage to the PDP Panel.

Watching the PDP TV in 4:3 format for a long period of time may leave traces

of borders displayed on the left, right and centre of the screen caused by the

difference of light emission on the screen. Playing a DVD or a game console

may cause similar effect to the screen. Damages caused by the above effect are

not covered by the Warranty.

 Afterimage on the Screen.

Displaying still images from Video games and PC for longer than a certain period of time may

produce partial afterimages. To prevent this effect, reduce the ‘brightness’ and ‘contrast’ when

displaying still images.

 Warranty

- Warranty does not cover any damage caused by image retention.

- Burn-in is not covered by the warranty.

 Installation

Be sure to contact an authorized service centre, when installing your set in a location with heavy

dust, high or low temperatures, high humidity, chemical substance and where it operates continually

such as the airport, the train station etc. Failure to do so may cause a serious damage to your set.

BN68-01294B,C-01Eng_CIS.indd 2 2007-10-08 ¿ÀÈÄ 3:32:30

English - 3

Symbols

☛ ➢

Press

Important

Note

Contents

General Information

 User Instructions ............................................. 2

 Checking Parts ................................................ 4

 Using the Stand-Base ..................................... 4

 Control Panel ................................................. 5

 Connection Panel ............................................ 6

 Viewing the Remote Control (PS42Q91HR/

PS42Q92HR/PS50Q91HR/PS50Q92HR) ...... 8

 Viewing the Remote Control (PS42C91HR/

PS50C91HR/PS42C92HR/PS50C92HR) ....... 9

Operation

 Switching Your Television On and Off ........... 10

 Viewing the Menus ........................................ 11

 Freezing the Current Picture ......................... 11

 Plug & Play Feature ...................................... 12

 Viewing an External Signal Sources ............. 13

 Editing Device Names ................................... 14

Channel Control

 Storing Channels Automatically .................... 14

 Storing Channels Manually ........................... 15

 Adding / Locking Channels ........................... 16

 Sorting the Stored Channels ......................... 17

 Assigning Names to Channels ...................... 17

 Fine Tuning Channel Reception .................... 18

 LNA ............................................................... 18

Picture Control

 Changing the Picture Standard ..................... 19

 Customizing the Picture Settings .................. 19



Conﬁguring Detailed Settings on the Picture

.. 20

 Selecting the Picture Size ............................. 21

 Selecting the Screen Mode ........................... 21

 Digital NR / Active Colour / DNIe /

Movie Plus .................................................... 22

Sound Control

 Sound Features ............................................ 23

 Selecting the Sound Mode

(depending on the model) ............................. 24

Function Description

 Time Features ............................................... 25

 Language / Blue Screen / Melody /

Light Effect / Energy Saving /

HDMI Black Level ......................................... 26

 Using the Game Mode .................................. 27

 Wall- mount adjustment (Sold separately) .... 28

 Viewing the Picture in Picture (PIP) .............. 29

 Screen Burn Protection ................................. 30

PC Display

 Setting up Your PC Software

(Based on Windows XP) ............................... 31

 Input Mode (PC) ............................................ 32

 Setting the PC ............................................... 33

 Setting the Home Theatre PC ....................... 34

About Anynet+ (PS42Q91HR/PS42Q92HR/PS50Q91HR/PS50Q92HR)

 What is Anynet+? .......................................... 35

 Connecting Anynet+ Devices ........................ 35

 Setting Up Anynet+ ....................................... 36

 Scanning and Switching between Anynet+

Devices ......................................................... 36

 Recording ...................................................... 37

 Listening through a Receiver ........................ 38

 Check Points before Requesting Service ..... 38

Appendix

 Teletext Feature (depending on the model) .. 39

 Wall Mount Kit Speciﬁcations (VESA) ........... 41

 Setting Up Your Remote Control

(PS42Q91HR/PS42Q92HR/PS50Q91HR/

PS50Q92HR) ................................................ 42

 How to assemble the Stand-Base

(depending on the model) ............................. 47

 Troubleshooting ............................................ 47

 Speciﬁcations ................................................ 48

BN68-01294B,C-01Eng_CIS.indd 3 2007-10-08 ¿ÀÈÄ 3:32:30

English - 4

Checking Parts

Owner’s Instructions Remote Control/

AAA Batteries

Power Cord Cloth-Clean

Warranty Card/

Registration Card/

Safety Guide Manual

Cover-Bottom / Screws (2ea)

(Refer to page 47)

Ferrite Core for Power Cord/

S-Video Cable

Ferrite Core for

Headphones Cable/

Power Cord

Sold Separately

S-Video Cable Antenna Cable Component Cables Audio Cables Video Cable

PC Cable Scart Cable PC Audio Cable HDMI Cable HDMI/DVI Cable

➢

Ferrite Core (Power Cord, Headphones Cable, S-Video Cable)

The ferrite core is used to shield the cable from interference.

When connecting a cable, open the ferrite core and clip it

around the cable.

Using the Stand-Base

➢



Two or more people should carry

the PDP. Never lay the PDP on the

floor because of possible damage

to the screen. Always keep the

PDP upright.



The PDP can rotate 20 degrees in

right and left directions.

-20° ~ 20°

BN68-01294B,C-01Eng_CIS.indd 4 2007-10-08 ¿ÀÈÄ 3:32:33

English - 5

Control Panel

1

SOURCE

Displays a menu of all of the available input

sources (TV, Ext.1, Ext.2, AV, S-Video,

Component, PC, HDMI1, HDMI2, and HDMI3).

➢

HDMI3 mode is available only in

PS42Q91HR/PS42Q92HR/PS50Q91HR/

PS50Q92HR models.

2

MENU

Press to see the on-screen menu of your TV’s

features.

3

+



−

Press to increase or decrease the volume.

In the on-screen menu, use the +



−

buttons as you use the ◄ and ► buttons on

the remote control.

4

C/P.

Press to change channels. In the on-screen

menu, use the C/P. buttons as

you use the ▲ and ▼ buttons on the remote

control.

5

(ENTER)

Press to confirm a selection.

6

(Power) button

Press to turn the TV on and off.

Power Indicator

− Power Off: Blue

− Power On: Off

Remote Control Sensor

Aim the remote control towards this spot on

the TV.

➢

The product colour and shape may vary depending on the model.

Front (or Side) Panel

Speaker

BN68-01294B,C-01Eng_CIS.indd 5 2007-10-08 ¿ÀÈÄ 3:32:35

English - 6

Connection Panel

1

HDMI IN 3 (PS42Q91HR/PS42Q92HR/

PS50Q91HR/PS50Q92HR)

Connect to the HDMI jack of a device with

HDMI output.

2

S-VIDEO or VIDEO / AUDIO L/R

Video (S-Video or Video) and audio inputs for

external devices, such as a camcorder or VCR.

3

Headphones jack

You can connect a set of headphones if you

wish to watch a television programme without

disturbing the other people in the room.

➢

Prolonged use of headphones at a high

volume may damage your hearing.

Continued...

☛



Whenever you connect an audio or video system to your set, ensure that all elements are

switched off.



When connecting an external device, match the colour of the connection terminal to the cable.

➢

The product colour and shape may vary depending on the model.

➢

The product colour and shape may vary depending on the model.

Side Panel

3

or

1

Rear Panel

1

3

6

4

2

Cable Television

Network

8

5

7

or

2

BN68-01294B,C-01Eng_CIS.indd 6 2007-10-08 ¿ÀÈÄ 3:32:38

English - 7

1

POWER IN

Connect the supplied power cord.

2

Connecting external Audio Devices

Connect RCA audio signals from the TV to an

external source, such as Audio equipment.

3

EXT 1, EXT 2

Inputs or outputs for external devices, such as

VCR, DVD, video game device or video disc

players.

Input/Output Specification

Connector

Input Output

Video Audio(L/R)

RGB Video + Audio(L/R)

EXT 1

✔ ✔ ✔

Only TV or DTV

output is available.

EXT 2

✔ ✔

Output you can

choose.

4

COMPONENT IN

Audio (AUDIO L/R) and video (Y/PB/PR) inputs

for Component.

5

SERVICE

− Connector for service.

− Connect the serial jack between the electro-

motion wall mount bracket and your TV

when you want to adjust the TV viewing

angle using your remote control.

6

PC IN / AUDIO

Connect to the video and audio output jack on

your PC.

7

HDMI IN 1, HDMI IN 2

− Connect to the HDMI jack of a device with

HDMI output. These inputs can also be used

as a DVI connection with separate analog

audio inputs. An optional HDMI/DVI cable

will be necessary to make this connection.

When using the optional HDMI/DVI adapter,

the DVI analog audio inputs on your TV

allow you to receive left and right audio from

your DVI device. (Not compatible with PC)

− When connecting this product via HDMI or

DVI to a Set Top Box, DVD Player or Games

Console etc, make sure that it has been

set to a compatible video output mode as

shown in the table below. Failure to observe

this may result in picture distortion, image

breakup or no picture.

− Do not attempt to connect the HDMI/DVI

connector to a PC or Laptop Graphics Card.

(This will result in a blank screen being

displayed)

DVI IN (HDMI 2) AUDIO L/R

DVI audio outputs for external devices.

8

ANT IN

75Ω Coaxial connector for Aerial/Cable

Network.

Supported modes for HDMI and Component

480i 480p 576i 576p 720p 1080i

HDMI/DVI 50Hz X X X O O O

HDMI/DVI 60Hz X O X X O O

Component O O O O O O

BN68-01294B,C-01Eng_CIS.indd 7 2007-10-08 ¿ÀÈÄ 3:32:39

English - 8

Viewing the Remote Control (PS42Q91HR/PS42Q92HR/PS50Q91HR/PS50Q92HR)

➢



This is a special remote control for the visually impaired persons, and has Braille points on the

Power, Channel, Volume, STOP, and PLAY/PAUSE buttons.



The performance of the remote control may be affected by bright light.

1

POWER button (turns the TV

on and off)

2

Number buttons for direct

channel access

3

One/Two-digit channel

selection

4

Channel control button

(Refer to page 16)

5

Selects the TV mode directly

6

Volume increase

Volume decrease

7

Temporary sound switch-off

8

Displays the main on-screen

menu

9

Returns to the previous

menu

0

Sound effect selection (Refer

to page 23)

!

Picture effect selection

(Refer to page 19)

#

Picture-In-Picture On/Off

$

Sound mode selection

%

TruSurround XT mode

button

^

Remote control setup

&

Selects a target device to be

controlled by the Samsung

remote control (TV, DVD,

STB, CABLE, VCR)

*

Press to backlight the VOL,

CH, and the active source

button (TV, DVD, CABLE,

STB, VCR) on the remote.

(

Available source selection

)

Previous channel

a

Automatic Power-off

b

Records for Live

Broadcasting

c

VCR/DVD Function (Rewind,

Stop, Play/Pause, Fast/

Forward

d

Next channel

Previous channel

e

Exit the on-screen menu

f

Control the cursor in the

menu

g

Use to see information on

the current broadcast

h

Runs the Anynet

+

view

functions and sets up

Anynet

+

devices.

i

Picture freeze

j

Picture size selection

l

Select the channel of sub

picture (PIP)

n

If your remote control is not

functioning properly, take

out the batteries and press

the reset button for about

2~3 seconds. Re-insert the

batteries and try using the

remote control again.

Teletext Functions

(Refer to page 39)

5

Exit from the teletext display

(depending on the model)

8

Teletext index

@

Teletext display/mix both

teletext information and the

normal broadcast

#

Teletext hold

(

Teletext mode selection

(LIST/FLOF)

)

Teletext sub page

d

P :Teletext next page

P :Teletext previous page

e

Teletext cancel

g

Teletext reveal

k

Fastext topic selection

m

Teletext size

o

Teletext store

Continued...

BN68-01294B,C-01Eng_CIS.indd 8 2007-10-08 ¿ÀÈÄ 3:32:41

English - 9

Viewing the Remote Control (PS42C91HR/PS50C91HR/PS42C92HR/PS50C92HR)

➢



This is a special remote control for the visually impaired persons, and has Braille points on the

POWER, Volume and Channel buttons.



The performance of the remote control may be affected by bright light.

1

POWER button

(turns the TV on and off)

2

Number buttons for direct

channel access

3

One/Two-digit channel

selection

4

Channel control button

(Refer to page 16)

5

Selects the TV mode directly

6

:Volume increase

:Volume decrease

7

Displays the main on-screen

menu

8

Temporary sound switch-off

9

Use to see information on

the current broadcast

0

Returns to the previous

menu

!

Sound effect selection

(Refer to page 23)

@

Picture effect selection

(Refer to page 19)

#

Adjusts screen brightness to

save energy.

$

Sound mode selection

%

Picture-In-Picture Off/On

^

TruSurround XT mode

button

&

Available source selection

*

Previous channel

(

Automatic Power-off

)

Selects the HDMI mode

directly.

a

:Next channel

:Previous channel

b

Exit the on-screen menu

c

Change confirmation

d

Move to the required menu

option / Adjust an option

value respectively

f

Picture freeze

g

Picture size selection

i

Sub picture (PIP) channel

selection

j

Sub picture (PIP) source

selection

k

Sub picture (PIP) location

selection

Teletext Functions

(Refer to page 39)

5

Exit from the teletext display

(depending on the model)

7

Teletext index

9

Teletext reveal

%

Teletext hold

&

Teletext mode selection

(LIST/FLOF)

*

Teletext sub page

a

P :Teletext next page

P :Teletext previous page

b

Teletext cancel

e

Teletext display/mix both

teletext information and the

normal broadcast

h

Fastext topic selection

j

Teletext store

k

Teletext size

Continued...

BN68-01294B,C-01Eng_CIS.indd 9 2007-10-08 ¿ÀÈÄ 3:32:44

English - 10

Installing Batteries in the Remote Control

1 Lift the cover at the back of the remote control upward as

shown in the figure.

2 Install two AAA size batteries.

➢

 Make sure to match the “+” and “–” ends of the

batteries with the diagram inside the compartment.

 Do not mix battery types, i.e. alkaline and manganese.

3 Close the cover as shown in the figure.

➢

Remove the batteries and store them in a cool and dry

place if you won’t be using the remote control for a long

time. The remote control can be used up to about 23 feet

from the TV. (Assuming typical TV usage, the batteries last

for about one year.)

➢

If the remote control doesn’t work! Check the following:

1. Is the TV power on?

2. Are the plus and minus ends of the batteries reversed?

3. Are the batteries drained?

4. Is there a power cut, or is the power cord unplugged?

5. Is there a special fluorescent light or a neon sign nearby?

Switching Your Television On and Off

The main lead is attached to the rear of the television.

1 Plug the main lead into an appropriate socket.

➢

The main voltage is indicated on the rear of the television and the frequency is 50 or 60Hz.

2 Press the (Power) button (On/Off) on the front of the television or press the POWER button on the

remote control to switch the television on. The programme that you were watching last is re-selected

automatically. If you have not yet stored any channels, no clear picture appears. Refer to “Storing

Channels Automatically” on page 14 or “Storing Channels Manually” on page 15.

➢

If the television is initially powered on, several basic customer settings proceed automatically.

Refer to “Plug & Play Feature” on page 12.

3 To switch the television off, press the (Power) button (On/Off) on the front of the television or press

the POWER button on the remote control.

4 To switch the TV on, press the (Power) button (On/Off) on the front of the TV or press the POWER

button or number buttons on the remote control.

BN68-01294B,C-01Eng_CIS.indd 10 2007-10-08 ¿ÀÈÄ 3:32:45

English - 11

Viewing the Menus

1 Press the MENU button.

The main menu is displayed on the screen.

Its left side has five icons: Picture, Sound, Channel, Setup,

and Input.

2 Press the ▲ or ▼ button to select one of the icons.

Press the ENTER button to access the icon’s sub-menu.

3 Press the ▲ or ▼ button to move to items in the menu.

Press the ENTER button to enter items in the menu.

4 Press the ▲/▼/◄/► button to change the selected items.

Press the RETURN button to return to the previous menu.

5 Press the EXIT button to exit from the menu.

➢

The illustration for remote control and OSD (On Screen

Display) shown in this manual has been created based on the

PS42Q91HR model. Even though the configuration is different

from your model, the operation method is the same as in the

illustration.

Freezing the Current Picture

You can freeze the picture when watching a television

programme simply by pressing the “STILL” button. To return to

normal viewing, press it again.

➢

This function will automatically cancel five minutes later.

Move

Enter

Exit

Mode :

Dynamic 

Contrast 100

Brightness 45

Sharpness 75

Colour 55

Tint G 50 R 50

Colour Tone :

Cool1 

Detailed Settings 

 More

Picture

T V

BN68-01294B,C-01Eng_CIS.indd 11 2007-10-08 ¿ÀÈÄ 3:32:46

English - 12

Plug & Play Feature

When the television is initially powered on, several basic

customer settings proceed automatically and subsequently.

The following settings are available.

☛

If you accidentally select the wrong country for your TV, the

characters on the screen may be wrongly displayed.

1 If the television is in standby mode, press the POWER button

on the remote control. The message Start Plug & Play is

displayed. Press the ENTER button.

2 The Language menu will automatically appear after several

seconds.

3 Select the appropriate language by pressing the ▲ or ▼ button.

Press the ENTER button. The message Select Home Mode

when installing this TV at home. is displayed.

4 Press the ◄ or ► button to select Shop or Home, then press

the ENTER button. The message to check the connected status

of the antenna is displayed.

➢

The default selection is Home.

➢

We recommend setting the TV to Home mode for the best

picture in your home environment.

➢

Shop mode is only intended for use in retail environments.

➢

If the unit is accidentally set to Shop mode, and you want to

return to Dynamic (Home) mode, press the Volume button

and then hold down the MENU button for five seconds on

the TV panel.

5 Make sure that the antenna is connected to the TV.

Press the ENTER button. The Country menu is displayed.

6 Select your country or area by pressing the ▲ or ▼ button.

Press the ENTER button. The menu to select channels is

displayed.

7 To start channel store, press the ENTER button.

The search will end automatically. The TV will begin memorizing

all of the available channels.

Press the ENTER button to set the clock.

8 Press the ◄/►/ENTER button to select Month, Day, Year,

Hour, or Minute. Set these by pressing the ▲ or ▼ button.

➢

You can set the Month, Day, Year, Hour, or Minute

directly by pressing the numeric buttons on the remote

control.

9 Press the ENTER button to confirm your setting.

The message Enjoy your viewing is displayed.

When you have finished, press the ENTER button.

➢

Even if the ENTER button is not pressed, the message will

automatically disappear after several seconds.

➢

Plug & Play feature is available in the TV mode only.

Continued...

Plug & Play

Start Plug & Play.

OK

Enter

Return

Plug & Play

Language

Move

Enter

Skip

English

Deutsch

Français

Italiano

▼

Plug & Play

Select Home Mode

when installing this TV at home.

Move

Enter

Skip

Shop

Home

Plug & Play

Country

Move

Enter

Skip

Belgium

France

Germany

Italy

▼

Plug & Play

Auto Store

P 1 C -- 40 MHz

0 %

Enter

Skip

Start

Plug & Play

Check antenna input.

Enter

Skip

OK

Enjoy your viewing

Plug & Play

Adjust

Move

Enter

01 01

2007

12

00

Clock Set

Month Day Year Hour

Minute





BN68-01294B,C-01Eng_CIS.indd 12 2007-10-08 ¿ÀÈÄ 3:32:48

English - 13

Viewing an External Signal Sources

You can switch between viewing signals from connected

equipment, such as a VCR, DVD, Set-Top Box, and the TV

source (broadcast or cable).

1 Press the MENU button to display the menu.

2 Press the ▲ or ▼ button to select Input, then press the ENTER

button.

3 Press the ENTER button again to select Source List.

4 Press the ▲ or ▼ button to select the signal source, then press

the ENTER button.

Available signal sources:

TV, Ext.1, Ext.2, AV, S-Video,

Component, PC, HDMI1, HDMI2, HDMI3

➢

HDMI3 mode is available only in PS42Q91HR/

PS42Q92HR/PS50Q91HR/PS50Q92HR models.

➢

You can select these options simply by pressing the SOURCE

button on the remote control.

➢

To watch television programme again, press the TV button and

select the channel number required.

If you want to reset this feature …

1 Press the MENU button to display the menu.

2 Press the ▲ or ▼ button to select Setup, then press the

ENTER button.

3 Press the ENTER button again to select Plug & Play.

The message Start Plug & Play is displayed.

Move

Enter

Return

Source List :

TV 

Edit Name



Anynet+



Input

T V

Move

Enter

Return

TV

Ext.1 :

−−−−

Ext.2 :

−−−−

AV : −−−−

S-Video :

−−−−

Component :

−−−−

PC :

−−−−

HDMI1 :

−−−−

HDMI2 : −−−−

HDMI3 :

−−−−

Source List

T V

Move

Enter

Return

Plug & Play 

Language :

English 

Time



Game Mode : Off 

Blue Screen :

Off 

Melody :

Off 

PC



Home Theatre PC : Off 

Light Effect :

Off 

 More

Setup

T V

BN68-01294B,C-01Eng_CIS.indd 13 2007-10-08 ¿ÀÈÄ 3:32:49

English - 14

Editing Device Names

You can give a name to the external source.

1 Press the MENU button to display the menu.

2 Press the ▲ or ▼ button to select Input, then press the ENTER

button.

3 Press the ▲ or ▼ button to select Edit Name, then press the

ENTER button.

4 Press the ▲ or ▼ button to select the external source to be

edited, then press the ENTER button.

5 Select the required device by pressing ▲ or ▼, then press the

ENTER button.

Available device names:

VCR, DVD, D-VHS, Cable STB, HD

STB, Satellite STB, AV Receiver, DVD Receiver, Game,

Camcorder, DVD Combo, DHR (DVD HDD Recorder), PC.

6 Press the EXIT button to exit.

➢

HDMI3 mode is available only in PS42Q91HR/

PS42Q92HR/PS50Q91HR/PS50Q92HR models.

➢

When a PC with a resolution of 640 x 480@60Hz is

connected to the HDMI IN 1 port, you should set the HDMI1

mode to PC in the Source List of Input mode. If the HDMI1

mode is not PC, it may work depending on the TV setting.

Storing Channels Automatically

You can scan for the frequency ranges available to you

(availability depends on your country).

Automatically allocated programme numbers may not

correspond to actual or desired programme numbers. However

you can sort numbers manually and clear any channels you do

not wish to watch.

1 Press the MENU button to display the menu.

2 Press the ▲ or ▼ button to select Channel, then press the

ENTER button.

3 Press the ENTER button again. The available countries are

listed.

4 Select your country by pressing the ▲ or ▼ button, then press

the ENTER button.

5 Press the ▲ or ▼ button to select Auto Store, then press the

ENTER button.

6 Press the ENTER button again to start the search.

The search will end automatically.

➢

To stop the search before it has finished, press the MENU

or the ENTER button.

Move

Enter

Return

Source List :

TV 

Edit Name



Anynet+



Input

T V

Move

Enter

Return

Country :

Belgium 

Auto Store



Manual Store



Channel Manager



Sort



Name



Fine Tune



LNA :

Off 

Channel

T V

Move

Enter

Return

Ext.1 : −−−−

Ext.2 :

−−−−

AV :

−−−−

S-Video :

−−−−

Component :

−−−−

PC :

−−−−

HDMI1 :

−−−−

HDMI2 :

−−−−

HDMI3 :

−−−−

Edit Name

T V

−−−−

VCR

DVD

D-VHS

Cable STB

HD STB

Satellite STB

▼

Auto Store

P 1 C -- 40 MHz

0 %

Enter

Return

Start

Move

Enter

Return

Country : Belgium

Auto Store

Manual Store

Channel Manager

Sort

Name

Fine Tune

LNA :

Off

Channel

T V

Belgium

France

Germany

Italy

Netherlands

Spain

▼

BN68-01294B,C-01Eng_CIS.indd 14 2007-10-08 ¿ÀÈÄ 3:32:51

English - 15

Storing Channels Manually

You can store television channels, including those received via

cable networks.

When storing channels manually, you can choose:

 Whether or not to store each of the channels found.

 The programme number of each stored channel which you wish

to identify.

1 Press the MENU button to display the menu.

2 Press the ▲ or ▼ button to select Channel, then press the

ENTER button.

3 Press the ▲ or ▼ button to select Manual Store, then press

the ENTER button.

4 Select the required option by pressing the ▲ or ▼ button, then

press the ENTER button.

5 When you are satisfied with your setting, press the ENTER

button.

6 Press the EXIT button to exit.

 Programme (Programme number to be assigned to a channel)

− Press the ▲ or ▼ button until you find the correct number.

➢

You can also select the channel number directly by

pressing the numeric buttons (0~9).

 Colour System: Auto/PAL/SECAM/NTSC4.43

− Press the ▲ or ▼ button to select the required colour standard.

 Sound System: BG/DK/I/L

− Press the ▲ or ▼ button to select the required sound standard.

 Channel (When you know the number of the channel to be stored)

− Press the ▲ or ▼ button to select C (Air channel) or S (Cable channel).

− Press the ► button, then press the ▲ or ▼ button to select the required number.

➢

You can also select the channel number directly by pressing the numeric buttons (0~9).

➢

If there is abnormal sound or no sound, re-select the sound standard required.

 Search (When you do not know the channel numbers)

− Press the ▲ or ▼ button to start the search.

− The tuner scans the frequency range until the first channel or the channel that you selected is

received on the screen.

 Store (When you store the channel and associated programme number)

− Set to OK by pressing the ENTER button.

☛

Channel mode

 P (Programme mode): When completing tuning, the broadcasting stations in your area have

been assigned to position numbers from P00 to P99. You can select a channel by entering the

position number in this mode.

 C (Air channel mode): You can select a channel by entering the assigned number to each air

broadcasting station in this mode.

 S (Cable channel mode): You can select a channel by entering the assigned number for each

cable channel in this mode.

Move

Enter

Return

Country :

Belgium 

Auto Store



Manual Store



Channel Manager



Sort



Name



Fine Tune



LNA :

Off 

Channel

T V

Move

Enter

Return

Programme :

P 1

Colour System :

Auto 

Sound System :

BG 

Channel :

C 4

Search :

63 MHz

Store :

?

Manual Store

T V

BN68-01294B,C-01Eng_CIS.indd 15 2007-10-08 ¿ÀÈÄ 3:32:51

English - 16

Adding / Locking Channels

Using the Channel Manager, you can conveniently lock or add

channels.

1 Press the MENU button to display the menu.

2 Press the ▲ or ▼ button to select Channel, then press the

ENTER button.

3 Press the ▲ or ▼ button to select Channel Manager, then

press the ENTER button.

 Adding channels

Using the Channel List, you can add channels.

4 Select Channel List by pressing the ENTER button.

5 Move to the ( ) field by pressing the ▲/▼/◄/► buttons,

select a channel to be added, and press the ENTER button to

add the channel.

➢

If you press the ENTER button again, the ( ) symbol next

to the channel disappears and the channel is not added.

 Locking channels

This feature allows you to prevent unauthorized users, such as

children, from watching unsuitable programmes by muting out

video and audio.

6 Press the ▲ or ▼ button to select Child Lock, then press the ENTER

button.

7 Select On by pressing the ▲ or ▼ button, then press the ENTER

button.

8 Press the ▲ or ▼ button to select Channel List, then press the

ENTER button.

9 Move to the ( ) field by pressing the ▲/▼/◄/► buttons, select a

channel to be locked, and press the ENTER button.

➢

If you press the ENTER button again, the ( ) symbol next to the

channel disappears and the channel lock is canceled.

➢

A blue screen is displayed when Child Lock is activated.

10 Press the EXIT button to exit.

➢

You can select these options simply by pressing the CH LIST

button on the remote control.

Move

Enter

Return

Country :

Belgium 

Auto Store



Manual Store



Channel Manager



Sort



Name



Fine Tune



LNA :

Off 

Channel

T V

Move

Enter

Return

Channel List

Child Lock :

Off 

Channel Manager

T V

Channel List

P 1 C 4

1 / 10

▲

▼

Prog.

0 C

-

1 C 4

2 C 24

3 C 2

4 C 5

5 C 80

6 C 7

7 C 36

8 C 52

9 C 11

Add Lock

Move Enter

Page

Return

BN68-01294B,C-01Eng_CIS.indd 16 2007-10-08 ¿ÀÈÄ 3:32:53

English - 17

Sorting the Stored Channels

This operation allows you to change the programme numbers

of the stored channels.

This operation may be necessary after using the auto store.

1 Press the MENU button to display the menu.

2 Press the ▲ or ▼ button to select Channel, then press the

ENTER button.

3 Press the ▲ or ▼ button to select Sort, then press the ENTER

button.

4 Select the channel that you wish to move by pressing the ▲ or

▼ button, then press the ENTER button.

5 Select the number of the programme to which the channel is to

be moved by pressing the ▲ or ▼ button.

Press the ENTER button. The channel is moved to its new

position and all other channels are shifted accordingly.

6 Repeat steps 4 to 5 until you have moved all the channels to

the required programme numbers.

7 Press the EXIT button to exit.

Assigning Names to Channels

Channel names will be assigned automatically when channel

information is broadcast. These names can be changed,

allowing you to assign new names.

1 Press the MENU button to display the menu.

2 Press the ▲ or ▼ button to select Channel, then press the

ENTER button.

3 Press the ▲ or ▼ button to select Name, then press the

ENTER button.

4 Press the ▲ or ▼ button to select the channel to be assigned to

a new name, then press the ENTER button.

5 Press the ▲ or ▼ button to select a letter, a number, or a

symbol (Results in this sequence: A~Z, 0~9, +, -, *, /, blank).

Move on to the previous or next letter by pressing the ◄ or ►

button, then press the ENTER button.

6 Repeat steps 4 to 5 for each channel to be assigned to a new

name.

7 Press the EXIT button to exit.

Move

Enter

Return

Country :

Belgium 

Auto Store



Manual Store



Channel Manager



Sort



Name



Fine Tune



LNA :

Off 

Channel

T V

Move

Enter

Return

Prog. Ch. Name



0 C−−

1 C76

2 C5

3 C6

4 C7 



Sort

T V

Move

Enter

Return

Prog. Ch. Name



0 C−− −−−−−

1 C76 −−−−−

2 C5 −−−−−

3 C6 −−−−−

4 C7 −−−−−



Name

T V

Move

Enter

Return

Country :

Belgium 

Auto Store



Manual Store



Channel Manager



Sort



Name



Fine Tune



LNA :

Off 

Channel

T V

BN68-01294B,C-01Eng_CIS.indd 17 2007-10-08 ¿ÀÈÄ 3:32:54

English - 18

Fine Tuning Channel Reception

If the reception is clear, you do not have to fine tune the

channel, as this is done automatically during the search and

store operation.

If the signal is weak or distorted, you may have to fine tune the

channel manually.

1 Press the MENU button to display the menu.

2 Press the ▲ or ▼ button to select Channel, then press the

ENTER button.

3 Press the ▲ or ▼ button to select Fine Tune, then press the

ENTER button.

4 To obtain a sharp, and clear picture and good sound quality,

press the ◄ or ► button until you reach the optimal setting.

Press the ENTER button.

➢

To reset the fine tuning to 0, select Reset by pressing the

▲ or ▼ button. Press the ENTER button.

5 Press the EXIT button to exit.

➢

Fine Tune Store will change the colour of the Channel OSD

(On Screen Display) from White to Red and add the “*”

mark.

LNA (Low Noise Amplifier)

This function is very useful in the situation that the TV is used

in weak signal.

LNA amplifies the TV signal in the weak signal area, a low-noise

preamplifier boosts the incoming signal.

1 Press the MENU button to display the menu.

2 Press the ▲ or ▼ button to select Channel, then press the

ENTER button.

3 Press the ▲ or ▼ button to select LNA, then press the ENTER

button.

4 Select Off or On by pressing the ▲ or ▼ button, then press the

ENTER button.

5 Press the EXIT button to exit.

➢

Depending on areas, factory mode of LNA, will be set up as On or Off.

Fine Tune

P 1

+3

Adjust

Save

Return

Reset

P 1 *

Mono

Picture : Dynamic

Sound : Custom

SRS TS XT : Off

−−

:

−−

Move

Enter

Return

Country :

Belgium 

Auto Store



Manual Store



Channel Manager



Sort



Name



Fine Tune



LNA :

Off 

Channel

T V

Move

Enter

Return

Country :

Belgium 

Auto Store



Manual Store



Channel Manager



Sort



Name



Fine Tune



LNA :

Off 

Channel

T V

BN68-01294B,C-01Eng_CIS.indd 18 2007-10-08 ¿ÀÈÄ 3:32:55

English - 19

Changing the Picture Standard

You can select the type of picture which best corresponds to

your viewing requirements.

1 Press the MENU button to display the menu.

2 Press the ENTER button to select Picture.

3 Press the ENTER button again to select Mode.

4 Select the required mode by pressing the ▲ or ▼ button, then

press the ENTER button.

Available modes:

Dynamic, Standard, Movie

➢

The settings values may vary depending on the input

source. (ex. RF, Video, Component, PC, or HDMI)

5 Press the EXIT button to exit.

➢

You can select these options simply by pressing the P.MODE

button on the remote control.

➢



Choose Dynamic for viewing the TV during the day or

when there is bright light in the room.



Choose Standard for general TV watching mode.



Choose Movie when viewing the movie.

Customizing the Picture Settings

Your television has several setting options that allow you to

control the picture quality.

1 Press the MENU button to display the menu.

2 Press the ENTER button to select Picture.

3 Press the ENTER button again to select Mode.

4 Select the required mode by pressing the ▲ or ▼ button, then

press the ENTER button.

Available modes:

Dynamic, Standard, Movie

5 Select the required option by pressing the ▲ or ▼ button, then

press the ENTER button.

6 When you are satisfied with your setting, press the ENTER

button.

7 Press the EXIT button to exit.

 Contrast – Brightness – Sharpness – Colour – Tint

➢

In TV, AV, S-Video modes of the PAL system, you cannot

use the Tint Function.

Contrast – Brightness – Colour Tone : PC Mode

Press the ◄ or ► button until you reach the optimal setting.

 Colour Tone: Cool2/Cool1/Normal/Warm1/Warm2

➢

When the picture mode is set to Dynamic or Standard, Warm1 and Warm2 cannot be selected.

 Reset: Cancel/OK

Select

OK. You can return to the factory defaults picture settings.

➢

The reset function is set for each picture mode and colour tone.

Move

Enter

Return

Mode :

Dynamic 

Contrast 100

Brightness 45

Sharpness 75

Colour 55

Tint G 50 R 50

Colour Tone :

Cool1 

Detailed Settings 

 More

Picture

T V

Move

Enter

Return

Mode : Dynamic

Contrast 100

Brightness 45

Sharpness 75

Colour 55

Tint G 50 R 50

Colour Tone :

Cool1

Detailed Settings 

 More

Picture

T V

Dynamic

Standard

Movie

Move

Enter

Return

Mode : Dynamic

Contrast 100

Brightness 45

Sharpness 75

Colour 55

Tint G 50 R 50

Colour Tone

: Cool1

Detailed Settings �

 More

Picture

T V

Cool2

Cool1

Normal

Warm1

Warm2

Move

Enter

Return

Mode :

Dynamic 

Contrast 100

Brightness 45

Sharpness 75

Colour 55

Tint G 50 R 50

Colour Tone :

Cool1 

Detailed Settings 

 More

Picture

T V

BN68-01294B,C-01Eng_CIS.indd 19 2007-10-08 ¿ÀÈÄ 3:32:57

English - 20

Configuring Detailed Settings on the Picture

You can set detailed picture settings.

1 Press the MENU button to display the menu.

2 Press the ENTER button to select Picture.

3 Press the ▲ or ▼ button to select Detailed Settings, then

press the ENTER button.

4 Select the required option by pressing the ▲ or ▼ button, then

press the ENTER button.

Available options: Black Adjust

, Dynamic Contrast, Gamma,

White Balance, My Colour Control, Edge Enhancement,

Colour Space

5 When you are satisfied with your setting, press the ENTER

button.

6 Press the EXIT button to exit.

➢

When the picture mode is set to Movie or Standard, Detailed

Settings can be selected.

➢

If DNIe is Off, the Detailed Settings cannot be selected when

the Picture mode is in Standard mode.

 Black Adjust: Off/Low/Medium/High

You can directly select the black level on the screen to adjust the screen depth.

 Dynamic Contrast: Off/Low/Medium/High

You can adjust the screen contrast so that the optimal contrast is provided.

 Gamma: -3 ~ +3

You can adjust the middle brightness of pictures.

Press the ◄ or ► button until you reach the optimal setting.

 White Balance: R-Offset/G-Offset/B-Offset/R-Gain/G-Gain/B-Gain/Reset

You can adjust the color temperature for more natural picture colors.

R-Offset/G-Offset/B-Offset/R-Gain/G-Gain/B-Gain: Changing the adjustment value will refresh the

adjusted screen.

Select the required option by pressing the ▲ or ▼ button, then press the ENTER button. Press the ◄

or ► button until you reach the optimal setting.

Reset: The previously adjusted white balance will be reset to the factory defaults.

 My Colour Control: Pink/Green/Blue/White/Reset

This setting can be adjusted to suit your personal preferences.

Pink/Green/Blue/White: Changing the adjustment value will refresh the adjusted screen.

Select the required option by pressing the ▲ or ▼ button, then press the ENTER button. Press the ◄

or ► button until you reach the optimal setting.

Reset: The previously adjusted colours will be reset to the factory defaults.

 Edge Enhancement: Off/On

You can emphasize object boundaries.

 Colour Space: Auto/Wide

You can set the colour reproduction space for the input signal to Auto or Wide.

Move

Enter

Return

Mode :

Movie 

Contrast 80

Brightness 65

Sharpness 35

Colour 35

Tint G 50 R 50

Colour Tone :

Warm2 

Detailed Settings 

 More

Picture

T V

Move

Enter

Return

Black Adjust : Off 

Dynamic Contrast :

Low 

Gamma :

0 

White Balance 

My Colour Control



Edge Enhancement

: Off 

Colour Space :

Wide 

Detailed Settings

T V

BN68-01294B,C-01Eng_CIS.indd 20 2007-10-08 ¿ÀÈÄ 3:32:58

La page charge ...

Samsung PS-50Q91HR Manuel utilisateur

Ce manuel convient également à

Samsung PS-50Q91HR Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents