Jenn-Air JXI8936DS Guide d'installation

Marque: Jenn-Air

Modèle: JXI8936DS

Catégorie: Hottes

Taper: Guide d'installation

JENN-AIR

36" (91.4 CM) ISLAND CANOPY

RANGE HOOD

HOTTE DE CUISINIÈRE JENN-AIR

POUR ÎLOT DE 36" (91,4 CM)

Installation Instructions and Use & Care Guide

For questions about features, operation/performance, parts, accessories, or service in the U.S.A., call:

1-800-JENNAIR (1-800-536-6247) or visit our website at www.jennair.com.

In Canada, call: 1-800-JENNAIR (1-800-536-6247), or visit our website at www.jennair.ca.

Instructions d’installation et Guide d’utilisation et d’entretien

Au Canada, pour assistance, installation ou service, composez le 1-800-JENNAIR (1-800-536-6247) ou visitez notre site web à

www.jennair.ca.

Table of Contents/Table des matières ............ 2

IMPORTANT: READ AND SAVE THESE INSTRUCTIONS.

FOR RESIDENTIAL USE ONLY.

IMPORTANT : LIRE ET CONSERVER CES INSTRUCTIONS.

POUR UTILISATION RÉSIDENTIELLE UNIQUEMENT.

2844/W10640312B

TABLE OF CONTENTS

RANGE HOOD SAFETY .................................................................3

INSTALLATION REQUIREMENTS ................................................5

Tools and Parts ............................................................................5

Location Requirements................................................................5

Venting Requirements..................................................................6

Electrical Requirements ...............................................................7

INSTALLATION INSTRUCTIONS ..................................................8

Prepare Location..........................................................................8

Install Range Hood.......................................................................9

Make Electrical Connection .......................................................11

Complete Installation .................................................................13

RANGE HOOD USE......................................................................13

Controls and Features................................................................13

RANGE HOOD CARE ...................................................................14

Cleaning......................................................................................14

WIRING DIAGRAM ......................................................................16

ASSISTANCE OR SERVICE.........................................................17

In the U.S.A. ...............................................................................17

In Canada ...................................................................................17

Accessories................................................................................17

WARRANTY ..................................................................................18

TABLE DES MATIÈRES

SÉCURITÉ DE LA HOTTE DE CUISINIÈRE................................19

EXIGENCES D'INSTALLATION...................................................21

Outils et pièces...........................................................................21

Exigences d’emplacement.........................................................21

Exigences concernant l'évacuation ...........................................22

Spécifications électriques ..........................................................23

INSTRUCTIONS D’INSTALLATION.............................................24

Préparation de l’emplacement...................................................24

Installation de la hotte ................................................................26

Raccordement électrique...........................................................28

Achever l’installation ..................................................................29

UTILISATION DE LA HOTTE .......................................................30

Commandes et caractéristiques................................................30

ENTRETIEN DE LA HOTTE..........................................................31

Nettoyage ...................................................................................31

SCHÉMA DE CÂBLAGE ..............................................................33

ASSISTANCE OU SERVICE.........................................................34

Au Canada..................................................................................34

Accessoires ................................................................................34

GARANTIE.....................................................................................18

RANGE HOOD SAFETY

You can be killed or seriously injured if you don't immediately

You

can be killed or seriously injured if you don't

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

follow instructions.

instructions.

DANGER

WARNING

State of California Proposition 65 Warnings:

WARNING: This product contains one or more chemicals known to the State of California to cause cancer.

WARNING: This product contains one or more chemicals known to the State of California to cause birth defects or other

reproductive harm.

IMPORTANT SAFETY INSTRUCTIONS

READ AND SAVE THESE INSTRUCTIONS

INSTALLATION REQUIREMENTS

Tools and Parts

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools

listed here.

Tools needed:

■ Level

■ Drill with 1¼" (3.0 cm), ½" (12.7 mm) and ³⁄₁₆" (5.0 mm)

drill bits

■ Pencil

■ Tape measure or ruler

■ Pliers

■ Caulking gun and weatherproof caulking compound

■ Vent clamps

■ Jigsaw or keyhole saw

■ Flat-blade screwdriver

■ Metal snips

■ Phillips screwdriver

■ ½" (13 mm) socket and driver with 24" (61 cm) of extensions

■ T20

®†

TORX

bit or driver

Parts needed:

■ Home power supply

■ ½" (12.7 mm) UL listed or CSA approved strain reliefs

For vented installations, you will also need:

■ 1 wall or roof cap

■ Metal vent system

For non-vented (recirculating) installations, you will

also need:

■ Chimney Kit Recirculation for non-vented (recirculating)

installations only. See “Assistance or Service” section

to order.

■ Charcoal Filter Part Number W10272069. See “Assistance

or Service” section to order.

Parts supplied:

Remove parts from packages. Check that all parts are included.

■ Hood canopy assembly with ventilator and lights installed

■ Mounting boss/damper/6" (15.2 cm) round flexible metal duct

7" (17.8 cm) long (not expanded)

■ Filter - installed in hood canopy

■ (4) 8 x 80 mm hanger bolts (T20

TORX

drive)

■ (4) 8 mm x ½" (13 mm) hex nuts

■ (4) 5 x 13 mm mounting screws (T20

TORX

drive)

■ Mounting template

■ Upper chimney cover

■ Lower chimney cover

■ ½" (13 mm) special nut tightening tool

■ Vent clamp for 6" (15.2 cm) duct

■ (2) 3.5 x 9.5 mm screws used for supporting the lower

chimney (located inside canopy behind filters).

Location Requirements

IMPORTANT: Observe all governing codes and ordinances.

Have a qualified technician install the range hood. It is the

installer's responsibility to comply with installation clearances

specified on the model/serial/rating plate. The model/serial/

rating plate is located behind the left filter on the rear wall of

the vent hood.

Canopy hood location should be away from strong draft areas,

such as windows, doors and strong heating vents.

Cabinet opening dimensions that are shown must be used. Given

dimensions provide minimum clearance.

This range hood is recommended for use with cooktops with a

maximum total rating of 78,000 BTUs or less.

Grounded electrical outlet is required. See “Electrical

Requirements” section.

Because of the size and weight of this island hood, the chimney

support must be securely attached to the ceiling.

■ The chimney support must be attached to joists. If this is not

possible, you must build a support structure behind the

plaster or drywall. The support structure must be able to

support 100 lbs (45.4 kg).

The range hood is factory set for venting through the roof or wall.

For non-vented (recirculating) Installation see “Non-vented

(recirculating) Installations” in “Install Range Hood” section.

Chimney Kit Recirculation and Charcoal Filter Kit Part Number

W10272069 are available from your dealer or an authorized parts

distributor. See “Assistance or Service” section to order.

All openings in ceiling and wall where range hood will be installed

must be sealed.

For Mobile Home Installations:

The installation of this range hood must conform to the

Manufactured Home Construction Safety Standards, Title 24

CFR, Part 328 (formerly the Federal Standard for Mobile Home

Construction and Safety, Title 24, HUD, Part 280) or when such

standard is not applicable, the standard for Manufactured Home

Installation 1982 (Manufactured Home Sites, Communities and

Setups) ANSI A225.1/NFPA 501A, or latest edition, or with local

codes.

Product Dimensions

†®T20 and TORX are registered trademarks of Acument Intellectual Properties, LLC.

A. 13" (33.0 cm)

B. 11¼" (28.6 cm)

C. 28" (71 cm) min.

45¼" (115 cm) max

D. 1

⁵⁄₈

" (4.2 cm)

E. 24" (61.0 cm)

F. 36" (91.4 cm)

Installation Dimensions

IMPORTANT:

Minimum distance “C”: 24" (61.0 cm) from electric cooking

surface, 30" (72.6 cm) from gas cooking surface

Suggested maximum distance “C”: 36" (91.4 cm)

NOTE: For best performance of the Auto Sense feature, the

range hood should be installed at 24" (61.0 cm) from an electric

cooking surface and 30" (76.2 cm) from a gas cooking surface.

The chimneys can be adjusted for different ceiling heights.

See the following chart.

*NOTE: The range hood chimneys are adjustable and designed

to meet varying ceiling or soffit heights depending on the

distance “C” between the bottom of the range hood and

the cooking surface. For higher ceilings from 10' (3.05 m),

a Stainless Steel Chimney Extension Kit is available from

your dealer or an authorized parts distributor. The chimney

extension replaces the upper chimney shipped with the

range hood. See “Assistance or Service” section to order

Venting Requirements

■ Vent system must terminate to the outside, except

for non-vented (recirculating) installations.

■ Do not terminate the vent system in an attic or other

enclosed area.

■ Do not use 4" (10.2 cm) laundry-type wall caps.

■ Use metal vent only. Rigid metal vent is recommended.

Do not use plastic or metal foil vent.

■ The vent system must have a damper. If the roof or wall

cap has a damper, do not use the damper supplied with

the range hood.

For the most efficient and quiet operation:

■ Use a straight run or as few elbows as possible.

■ Use no more than three 90° elbows.

■ Make sure there is a minimum of 24" (61.0 cm) of straight

vent between the elbows if more than 1 elbow is used.

■ Do not install 2 elbows together.

■ Use vent clamps to seal all joints in the vent system.

■ Use caulking to seal exterior wall or roof opening around

the cap.

■ The size of the vent should be uniform.

Cold Weather Installations:

An additional back draft damper should be installed to minimize

backward cold air flow and a thermal break should be installed

to minimize conduction of outside temperatures as part of the

vent system. The damper should be on the cold air side of the

thermal break.

The break should be as close as possible to where the vent

system enters the heated portion of the house.

Makeup Air:

Local building codes may require the use of makeup air systems

when using ventilation systems greater than specified CFM of

air movement. The specified CFM varies from locale to locale.

Consult your HVAC professional for specific requirements in

your area.

Venting Methods

This island hood is factory set for venting through the roof.

A 6" (15.2 cm) round vent system is needed for installation (not

included). The hood exhaust opening is 6" (15.2 cm) round.

A 6" to 8" (15.2 cm to 20.3 cm) vent adapter is available for 8"

(20.3 cm) vent systems. See the “Assistance or Service” section

to order.

Vent system can terminate either through the roof or wall.

To vent through a wall, a 90° elbow is needed.

A. Countertop height

B. Hood height from ceiling to bottom of the range hood:

E-A-C=B

C. Hood height: 24" (61.0 cm) min. from electric cooking

surface, 30" (76.2 cm) min. from gas cooking surface,

suggested 36" (91.2 cm) max.

D. Chimney assembly height: D = B-2

³⁄₈

" (6.0 cm)

E. Ceiling height

Vented Installations

Min. ceiling height Max. ceiling height

Electric cooking

surface

7' 6" (2.3 m) 10' (3.04 m)

Gas cooking

surface

8' (2.45 m) 10' (3.04 m)

Non-vented (recirculating) Installations

Min. ceiling height Max. ceiling height

Electric cooking

surface

7' 6" (2.3 m) 10' (3.04 m)

Gas cooking

surface

8' (2.45 m) 10' (3.04 m)

For Non-Vented (recirculating) Installations:

If it is not possible to vent cooking fumes and vapors to the

outside, the hood can be used in the non-vented (recirculating)

version, fitting a charcoal filter and the deflector. Fumes and

vapors are recycled through the upper chimney cover louvers.

To order charcoal filter and recirculation kit, see “Accessories”

in the “Assistance or Service” section.

NOTE: Wall venting can be an option for 2-story homes.

Calculating Vent System Length

To calculate the length of the system you need, add the

equivalent feet (meters) for each vent piece used in the system.

Maximum equivalent vent length is 35 ft (10.7 m).

Example Vent System:

The following example falls within the maximum vent length of

35 ft (10.7 m).

Electrical Requirements

Observe all governing codes and ordinances.

Ensure that the electrical installation is adequate and in

conformance with National Electrical Code, ANSI/NFPA 70

(latest edition), or CSA Standards C22.1-94, Canadian

Electrical Code, Part 1 and C22.2 No. 0-M91 (latest edition)

and all local codes and ordinances.

If codes permit and a separate ground wire is used, it is

recommended that a qualified electrician determine that

the ground path is adequate.

A copy of the above code standards can be obtained from:

National Fire Protection Association

1 Batterymarch Park

Quincy, MA 02169-7471

CSA International

8501 East Pleasant Valley Road

Cleveland, OH 44131-5575

■ A 120 volt, 60 Hz., AC only, 15-amp, fused electrical

circuit is required.

■ If the house has aluminum wiring, follow the

procedure below:

1. Connect a section of solid copper wire to the

pigtail leads.

2. Connect the aluminum wiring to the added section

of copper wire using special connectors and/or tools

designed and UL listed for joining copper to aluminum.

Follow the electrical connector manufacturer's recommended

procedure. Aluminum/copper connection must conform with

local codes and industry accepted wiring practices.

■ Wire sizes and connections must conform with the rating of

the appliance as specified on the model/serial/rating plate.

The model/serial/rating plate is located behind the filter on

the rear wall of the range hood.

■ Wire sizes must conform to the requirements of the National

Electrical Code, ANSI/NFPA 70 (latest edition), or CSA

Standards C22. 1-94, Canadian Electrical Code, Part 1

and C22.2 No. 0-M91 (latest edition) and all local codes

and ordinances.

Non-vented (recirculating) Roof Venting

A. Deflector

B. 6" (15.2 cm) round vent

A. Roof cap

B. 6" (15.2 cm) round vent

Vent piece 6" (15.2 cm) round

45° elbow 2.5 ft

(0.8 m)

90° elbow 5.0 ft

(1.5 m)

1 - 90° elbow = 5.0 ft (1.5 m)

1 - wall cap = 0.0 ft (0.0 m)

8 ft (2.4 m) straight = 8.0 ft (2.4 m)

System length = 13 ft (3.9 m)

90 elbow

6 ft (1.8 m)

2 ft

(0.6 m)

Wall cap

INSTALLATION INSTRUCTIONS

Prepare Location

■ It is recommended that the vent system be installed before

the range hood is installed.

■ Before making cutouts, make sure there is proper clearance

within the ceiling for exhaust vent.

■ Range hood is to be installed 24" (61.0 cm) min. for electric

cooking surfaces, 30" (76.2 cm) min. for gas cooking

surfaces, to a suggested maximum of 36" (91.4 cm) above

the cooking surface.

1. Disconnect power.

2. Determine which venting method to use: roof or non-vented.

3. Select a flat surface for assembling the range hood. Place

covering over that surface.

4. Using 2 or more people, lift range hood onto covered surface.

5. Remove the motor from the canopy assembly (see the “Motor

Removal” section in this section).

Motor Removal

To remove motor:

1. Remove the filter cover and metal grease filter (see the “Metal

Grease Filters” section in the Range Hood Care section).

2. Disconnect the blower motor wiring at the 9 pin connector.

3. Locate the special ½" (13 mm) tool inside the range hood

blower housing in the left front corner behind the insulation

pad. Use it to loosen the 4 nuts located inside the blower

housing that mounts the motor to the module top cover.

4. Grasp the motor plate and slide the motor toward the

back of the module housing to the large openings in

the keyhole slots.

5. Remove the motor from the range hood.

Range Hood Mounting Screws Installation

1. Determine and mark the centerline on the ceiling where the

range hood will be installed, considering the requirements for

ceiling support structures. See the “Location Requirements”

section. Make sure the range hood is centered over the

cooking surface.

Tape template in place on the ceiling at the marked centerline.

Align the front of the template with the front of the cooktop.

3. Use a pencil to mark the mounting screws, wire access and

duct hole locations on the ceiling.

NOTE: Mounting hole locations must be into the ceiling

support structure. The mounting structure in the ceiling must

be able to support 100 lbs (45.4 kg).

Remove the template.

4. Drill (4) ³⁄₁₆" (4.8 mm) pilot holes at the marked locations on

the ceiling for installing the hanger bolts.

5. Using a T20

Torx

bit and driver, install the (4) 8 x 80 mm

hanger bolts into the pilot holes. Leave approximately ¾"

(2 cm) protruding down from the ceiling.

6. Screw the nuts on the hanger bolts, but do not tighten.

A. Special ½" (13 mm) tool

B. Motor assembly

C. Keyhole slots (large opening) (4)

D. ½" (13 mm) motor mounting nuts (4)

E. Motor plate

F. Module top cover

WARNING

Excessive Weight Hazard

Use two or more people to move and install

range hood.

Failure to do so can result in back or other injury.

A. Blower housing

B. Keyhole slots (4)

C. Motor assembly

D. Motor plate

³⁄₄"

(2 cm)

Complete Preparation

For Vented installations only:

1. Determine and make all necessary cuts in the ceiling for

the vent system. Install the vent system before installing

the hood. See “Venting Requirements” section.

2. Using a jigsaw or keyhole saw , cut a 6½" (16.5 cm) diameter

hole in the ceiling for the vent duct.

3. Install the vent duct through the hole in the ceiling.

4. Connect the flexible vent section to the vent system.

NOTE: Mounting boss handle must be parallel with the front

of the range hood to align the mounting studs with the half

slots in the module top cover plate.

For Vented and Non-Vented installations:

1. Expand the flexible section of vent duct (supplied) to

approximately 12" (30.5 cm) to 24" (61.0 cm) depending

on the ceiling height.

NOTE: For ceiling heights above 9' (2.7 m), additional 6"

(15.2 cm) round duct (not supplied) will be required.

2. Loosen the four nuts on the mounting boss. (The back flange

of each nut should be approximately ³⁄₁₆" [5 mm] from the

face of the mounting boss.)

3. Secure all connections with vent clamps.

4. Determine the required location in the ceiling for the

home power supply cable and drill a 1¼" (3.2 cm) hole

at this location.

Top View:

Use flexible wiring. Crosshatch is the open area available for

wiring access in the ceiling within the upper chimney area.

5. Run the home power supply cable according to the National

Electrical Code or CSA Standards and local codes and

ordinances. There must be enough flexible wiring from the

fused disconnect (or circuit breaker) box to make the

connection in the hood’s electrical terminal box.

NOTE: Do not reconnect power until installation is complete.

6. Use caulk to seal all openings.

Install Range Hood

1. Slip the upper chimney cover over the assembled vent duct

and electrical outlet and slide it to the ceiling. Align the large

end of the keyhole slots in the top of the upper chimney cover

up over the nuts and then slide it into the smaller slot section

on the keyhole slots.

2. Using the ½" (13 mm) special tool (supplied) or a ½" (13 mm)

socket and driver with 24" of extensions, tighten the nuts to

fasten the upper chimney cover section to the ceiling.

A. 6" (15.2 cm) flexible metal duct

B. Mounting boss

C. Mounting boss handle

D. Mounting studs and nuts (4)

³⁄₁₆

" (5 mm)

F. Ve nt c lam p

G. 6" (15.2 cm) round vent

system duct

Vented Installation: Non-vented (recirculating)

Installation:

A. 1

¹¹⁄₁₆

" (4.3 cm)

B. 1

¹³⁄₁₆

" (4.8 cm)

C. 9

⁷⁄₈

" (24.9 cm)

⁵⁄₈

" (1.5 cm)

E. Electrical box

F. Front of range hood

G. 6" (15.2 cm) round duct

A. 7" (17.8 cm)

B. 1½" (3.8 cm)

⁵⁄₈

" (1.5 cm)

D. Air deflector

E. Electrical box

F. Front of range hood

3. Locate and remove the (2) 4 x 13 mm service screws inside

the range hood blower housing.

NOTE: These are be used to hold the lower chimney cover

up while assembling the range hood canopy to the upper

chimney cover.

4. Slide the lower chimney cover up over the upper chimney

cover until its bottom edge is above the holes on the upper

chimney cover front and back. While holding the lower

chimney cover, install the 4 x 13 mm service screws in

each side of the upper chimney cover. Leave approximately

¹⁄₈" (3 mm) between the head of the screw and the upper

chimney cover. Lower the lower chimney cover to rest on the

top of the screws. These screws will hold the lower chimney

cover up while assembling the range hood canopy to the

upper chimney cover.

5. Move the range hood to its mounting location and

connect the power supply. See the “Make Electrical

Connections” section.

6. Lift the range hood canopy into the approximate

recommended height for the cooktop type and install a

minimum of (4) 5 x 12 mm screws (D) (2 each side) through

the slots in the upper chimney cover and into the mounted

threaded fasteners (F) of the range hood canopy.

7. Adjust the range hood to the desired height. Level the

range hood and tighten the screws using a T20

Torx

bit.

See “Installation Dimensions” in the “Location Requirements”

section.

NOTE: Final height must be between the recommended

minimum and maximum dimension. The mounted threaded

fasteners (F) are for height adjustments during installation for

approved minimum and maximum distance between the

bottom of the range hood and the top of the cooking surface.

8. Reach inside the range hood cavity and grasp the handle of

the mounting boss. Pull down to align nuts through cutout

holes in the module top cover. Push back into half-slots to

assemble. Tighten (4) nuts using the ½" (13 mm) special tool

or ½" socket and driver with extension.

A. 4 x 13 mm service screws (2)

B. Inside area of range hood blower housing

A. Lower chimney cover (front)

B. Bottom edge of lower chimney cover

C. 4 x 13 mm screws

D. Upper chimney cover

A. Lower chimney cover

B. 4 x 13 mm screws

C. Upper chimney cover

¹⁄₈

" (3.2 mm)

A. Ceiling

B. Lower chimney cover

C. Upper chimney cover

D. Mounting screws (4)

E. Range hood canopy

assembly

F. Range hood canopy

mounted thread fasteners

9. Push up and hold the lower chimney cover, and remove the

(2) 4 x 13 mm screws. Slide the lower chimney cover down

onto the top of the range hood canopy.

10. Replace (2) 4 x 13 mm service screws into storage area

inside range hood blower housing.

11. Go to “Complete Installation” section.

Make Electrical Connection

1. Disconnect power.

2. Remove the (2) screws from the top of the electrical box

cover and set the screws and cover aside.

3. Using a T20

Torx

driver, remove the (4) screws from the wire

protector race panel and set the part and screws aside.

Do not damage the wiring.

4. Using a T20

Torx

driver, remove the (2) screws inside the

electrical box holding the module plate and the (6) other

screws around the perimeter of the module plate.

A. Lower chimney cover

B. 4 x 13 mm screw (2)

C. Upper chimney cover

D. Range hood canopy assembly

A. 4 x 13 mm service screws (2)

B. Inside area of range hood blower housing

WARNING

Electrical Shock Hazard

Disconnect power before servicing.

Replace all parts and panels before operating.

Failure to do so can result in death or electrical shock.

A. Electrical box cover

B. Screws - electrical box cover (2)

C. Wire protector race

D. Screws - wire protector race (4)

E. Electrical wiring

A. Screws - module top assembly (8)

B. Module plate assembly

C. Range hood module

5. Lift module plate assembly from top of range hood module

and position it to rest on top of the module.

6. Using a T20

Torx

driver, remove (2) screws from the

electrical connection box on the bottom of the module

plate assembly.

7. Remove knockout labeled “Elec IN” from the module top

plate, and install UL listed or CSA approved strain relief.

8. Run the flexible 3 wire home power supply cable from

the ceiling through the strain relief and into the electrical

connection box.

9. Use UL listed wire connectors and connect the

black wires together.

10. Use UL listed wire connectors and connect the

white wires together.

11. Connect the green (or bare) ground wire from the home

power supply cable to the green (or green/yellow) ground

wire in the electrical box using a UL listed wire connector.

12. Tighten strain relief to secure the home power supply cable.

13. Reassemble the electrical connection box cover

on the bottom of the module plate assembly.

14. Reassemble the module plate assembly to the top of the

range hood module and tighten the (8) assembly screws.

15. Reaassemble the electrical box cover and wire race to the

front of the range hood module.

A. Module plate assembly

B. Range hood module

A. Electrical connection box cover

B. Screws (2)

C. Electrical connection box

A. Bottom of module top plate

B. Elec IN knockout

A. UL listed or CSA approved

strain relief

B. 3-wire flexible home power

supply cable

C. Green, bare or yellow/green

wires

D. Black wires

E. White wires

F. UL listed wire connectors (3)

G. 3-wire flexible power cable

from electrical box

WARNING

Electrical Shock Hazard

Electrically ground blower.

Connect ground wire to green and yellow ground wire

in terminal box.

Failure to do so can result in death or electrical shock.

Complete Installation

Reinstall Motor:

1. Place the motor into the blower module housing positioning

it with the large keyholes in motor mounting plate towards

the back of the canopy.

2. Grasping the motor plate, push the motor up into the blower

module housing. Locate the large keyholes over the motor

mounting nuts, push up against the module top cover and

pull the motor forward to lock into the small keyholes slots.

3. Use the special ½" (13 mm) tool and tighten the (4) nuts to

secure the motor.

4. Reconnect 9 pin connector from motor to electrical power.

5. Reconnect power.

Complete Installation:

1. For non-vented (recirculating) installations only, install the

charcoal filters over the metal mesh filter. See the “Range

Hood Care” section.

2. Install metal filters. See the “Range Hood Care” section.

3. Check the operation of the range hood blower and light.

See the “Range Hood Use” section.

If range hood does not operate, check to see whether a

circuit breaker has tripped or a household fuse has blown.

NOTE: To get the most efficient use from your new range hood,

read the “Range Hood Use” section.

RANGE HOOD USE

The range hood is designed to remove smoke, cooking vapors

and odors from the cooktop area. For best results, start the

hood before cooking and allow it to operate several minutes

after the cooking is complete to clear all smoke and odors

from the kitchen.

The range hood controls are located on the front of the canopy.

Control Panel

Controls and Features

NOTES:

■ To activate the controls, press and release the desired button.

■ The control feature button will be lit when a control feature

is turned On.

Sleep Mode

The range hood automatically enters Sleep Mode when not

in use. After 10 minutes of no range hood activity, all of the

control button lights will turn Off. To deactivate Sleep Mode,

press any button.

Auto Sense

Auto Sense allows the range hood fan to turn on automatically

when it senses heat higher than its allowable temperature limit.

When Auto Sense is On, the fan speed will increase or decrease

based on the temperature Auto Sense is measuring.

Auto Sense can be manually increased by pressing a higher fan

speed. The fan will run at the selected speed for 10 minutes

before returning to the speed selected for Auto Sense.

If Auto Sense is On, the Auto button light will turn Off and go into

Sleep Mode when the vent hood is not in use. If the vent hood is

turned On by the consumer or by Auto Sense, the Auto button

light will turn On.

To set Auto Sense:

Press AUTO.

To Select Auto Sense Cooktop Type:

NOTE: The range hood is factory-set for the gas

cooktop mode.

Press and hold AUTO for 5 seconds to switch between

the gas cooktop and electric cooktop modes.

The Auto button light will flash 5 times when the range hood

is changed to the electric cooktop mode. Auto Sense is now

set to work with electric cooktops and ranges.

The Auto button light will flash 3 times when the range hood

is changed to the gas cooktop mode. Auto Sense is now set

to work with gas cooktops and ranges.

Changing the cooktop type will change the temperature limit

for Auto Sense to turn On. When the range hood senses

a high enough temperature, the fan will start automatically.

When the temperature drops below the set temperature limit,

the fan will stop automatically. The Auto button light will turn

Off after the range hood enters Sleep Mode, but Auto Sense

is still active.

A. Louver holes (non-vented

[recirculating] installations only)

B. Chimney covers

C. Lamps

D. Filter door glass

E. Canopy glass

F. Canopy

G. Control panel

Auto Low

Med

Hi Boost Filter Light

To Deactivate Auto Sense:

If the Auto button is lit, press AUTO once to deactivate

Auto Sense. The Auto button light will turn Off.

If Auto Sense is in Sleep Mode, press AUTO once to

deactivate Sleep Mode and turn the Auto button light On.

Press AUTO again to deactivate Auto Sense and turn Off

the Auto button light.

Auto Sense will automatically turn off after 2 hours of no

activation of the Auto Sense system. To reset Auto Sense,

press AUTO.

Manual Vent Functions

Timer

The range hood can be set to automatically turn off

after 15 minutes.

1. Press and hold the desired fan speed button for 2 seconds.

The fan will run on the chosen speed for 15 minutes and the

fan speed button light will flash continuously.

After 15 minutes, the fan will turn Off automatically.

2. Press the desired fan speed button again while the fan timer

is running to cancel the fan timer.

NOTE: Changing the fan speed or turning Auto Sense On will

also cancel the 15-minute timer.

Filter

The Filter button lights up when it is time to replace or clean the

filter. The button will be lit only when the fan is On. Press FILTER

after replacing the filter to turn the Filter button light Off. See the

“Cleaning” section for how to replace or clean the filter.

Light

Press LIGHT to turn the range hood lights On and Off.

RANGE HOOD CARE

Cleaning

IMPORTANT: Clean the hood and grease filters frequently

according to the following instructions. Replace grease filters

before operating hood.

Exterior Surfaces:

To avoid damage to the exterior surface, do not use steel wool or

soap-filled scouring pads.

Always wipe dry to avoid water marks.

Cleaning Method:

■ Liquid detergent soap and water, or all-purpose cleanser

■ Wipe with damp soft cloth or nonabrasive sponge, then rinse

with clean water and wipe dry.

Metal Grease Filters

The filter should be washed frequently. Place the metal filter in

the dishwasher or hot detergent solution to clean.

Let the filter dry thoroughly before replacing it.

NOTE: The metal grease filter is located behind the center glass

panel. The panel is hinged on the left side and magnetically

secured on the right side. To access the grease filter, grasp the

panel on the right-hand corners and pull down. This releases the

panel from the magnets and allows the panel to swing down.

Fan Speeds

Low Press LOW to turn the fan on at Low speed.

Med Press MED to turn the fan on at

Medium speed.

Hi Press HI to turn the fan on at High speed.

Boost Press BOOST to turn the fan on at the

highest speed. Boost will automatically turn

Off after 10 minutes and the fan will switch

to High speed.

A. Center glass panel

B. Magnets

To Remove Metal Grease Filters:

1. Turn off fan and lights.

2. Remove the filter holder frame and grease filter using a

flat-blade screwdriver to turn the grease filter release screws

90° counterclockwise.

To Replace Metal Grease Filter:

Replace grease filter and filter holder frame into range hood.

Align the grease filter release screw and use a flat-blade

screwdriver to turn the grease filter release screws 90° clockwise

to lock in place.

Charcoal Filters - For Non-Vented

(recirculating) Installations

NOTE: After approximately 3 years of use the charcoal filter

should be replaced. To order a replacement Charcoal Filter Kit,

see the “Assistance or Service” section.

The charcoal filters can be cleaned and reactivated. Clean the

filter in the dishwasher using normal detergent and choosing the

highest temperature setting.

To reactivate the filter, the filter should be dried in an oven for

10 minutes with a maximum temperature of 210°F (100°C).

To Remove Charcoal Filters:

1. Turn fan and lights off.

2. Remove the metal grease filters. See “Metal Grease

Filters” section.

3. Remove the upper and side lock springs.

4. Clean or discard the charcoal filter.

To Replace Charcoal Filters:

1. For non-vented (recirculating installations) install charcoal

filter, wrapping it around the grease filter.

2. Place the charcoal filter mat around the grease filter and

fix it in place by using the cap lock springs provided.

3. Position the upper cap and fix it in place using the cap lock

spring provided.

A. Grease filter release screw

B. Filter holder frame

C. Grease filter

A. Charcoal filter mat

B. Grease filter

C. Charcoal filter side lock springs

D. Upper cap

E. Cap lock spring

F. Grease filter support

WIRING DIAGRAM

Additional lamp only

in 4 lamps version

Fuse

RL2

RL4

RL1

FT1

FT2

FT6 FT4

FT5FT3

BK - 1

YL/

WH - 2

BK - 3

WH -

BU - 5

RD - 4

GY - 3

Motor Specifications

3.7 A

120 VAC

Blue - Red

Blue - Black

Frequency

Power Supply

Wattage Rating

14.90 Ohm

9.92 Ohm

22.00 Ohm

Amperage

Motor Speed/Resistance

18.40 Ohm

420 W

Blue - Gray

60 Hz

Blue - White

Component Layout

Description

Num.

E.M.I. Filter

User Interface

Main Board

Light Driver

Capacitor

LED Lamp

Temperature Sensor

Surge Protector

Motor

YL/

2 Speed

4 Speed

3 Speed

1 Speed

120 VAC

Not

used

Not

used

12 VDC

12 VDC12 VDC

12 VDC

YL/

SEL0099388

6 66

4 23

ASSISTANCE OR SERVICE

If you need service:

Please refer to the warranty page in this manual.

If you need replacement parts:

If you need to order replacement parts, we recommend that

you use only factory specified parts. Factory specified parts

will fit right and work right because they are made with the

same precision used to build every new appliance.

To locate factory specified replacement parts in your area, call

the following customer assistance telephone number or your

nearest designated service center.

In the U.S.A.

Call Jenn-Air Customer eXperience Center toll free:

1-800-JENNAIR (1-800-536-6247) or visit our website at

www.jennair.com.

Our consultants provide assistance with:

■ Scheduling of service. Jenn-Air

appliances designated

service technicians are trained to fulfill the product

warranty and provide after-warranty service anywhere

in the United States.

■ Features and specifications on our full line of appliances.

■ Referrals to local Jenn-Air

appliance dealers.

■ Installation information.

■ Use and maintenance procedures.

■ Accessory and repair parts sales.

■ Specialized customer assistance (Spanish speaking,

hearing impaired, limited vision, etc.).

For further assistance:

If you need further assistance, you can write to Jenn-Air

Appliances with any questions or concerns at:

Jenn-Air Brand Home Appliances

Customer eXperience Center

553 Benson Road

Benton Harbor, MI 49022-2692

Please include a daytime phone number in your correspondence.

In Canada

Call the Whirlpool Canada LP Customer eXperience Centre toll

free at 1-800-JENNAIR (1-800-536-6247) or visit our website at

www.jennair.ca.

Our consultants provide assistance with:

■ Scheduling of service. Jenn-Air

appliances designated

service technicians are trained to fulfill the product warranty

and provide after-warranty service anywhere in Canada.

■ Features and specifications on our full line of appliances.

■ Referrals to local Jenn-Air

appliance dealers.

■ Installation information.

■ Use and maintenance procedures.

■ Accessory and repair parts sales.

For further assistance:

If you need further assistance, you can write to Jenn-Air

Appliances with any questions or concerns at:

Jenn-Air Brand Home Appliances

Customer eXperience Centre

200 - 6750 Century Ave.

Mississauga, Ontario L5N 0B7

Please include a daytime phone number in your correspondence.

Accessories

Charcoal Filter Kit

(for non-vented installations only)

Order Part Number W10272069

Chimney Kit Recirculation

(for 7' 9" [2.36 m] to 9' 8" [2.95 m] ceilings)

(for non-vented installations only)

Order Part Number W10646865

Chimney Extension Kit - (vented)

(for 10' 2" [3.1 m] to 12' [3.66 m] ceilings)

Order Part Number W10646863

Chimney Extension Kit - (vented)

(for 9' 1" [2.77 m] to 11' [3.35 m] ceilings)

Order Part Number W10685946

Chimney Extension Kit - (recirculating)

(for 10' 2" [3.1 m] to 12' [3.66 m] ceilings)

(for non-vented installations)

Order Part Number W10685947

Chimney Extension Kit - (recirculating)

(for 9' 1" [2.77 m] to 11' [3.35 m] ceilings)

(for non-vented installations)

Order Part Number W10646866

6" (15.2 cm) Makeup Air Kit

(consult local building codes)

Order Part Number W10446915

Vent Duct Adapter 6" to 8" (15.2 cm to 20.3 cm)

(for 8" [20.3 cm] duct installations)

Order Part Number W10685950

12/14

JENN-AIR

MAJOR APPLIANCE

LIMITED WARRANTY

ATTACH YOUR RECEIPT HERE. PROOF OF PURCHASE IS REQUIRED

TO OBTAIN WARRANTY SERVICE.

Please have the following information available when you call the

Customer eXperience Center:

■ Name, address and telephone number

■ Model number and serial number

■ A clear, detailed description of the problem

■ Proof of purchase including dealer or retailer name and address

IF YOU NEED SERVICE:

1. Before contacting us to arrange service, please determine whether your product requires repair. Some

questions can be addressed without service. Please take a few minutes to review the Troubleshooting or

Problem Solver section of the Use and Care Guide, scan the QR code on the right to access additional

resources, or visit https://jennair.custhelp.com.

2. All warranty service is provided exclusively by our authorized Jenn-Air Service Providers

. In the U.S. and

Canada, direct all requests for warranty service to:

Jenn-Air Customer eXperience Center

1-800-JENNAIR (1-800-536-6247)

If outside the 50 United States or Canada, contact your authorized Jenn-Air dealer to determine whether another warranty applies.

https://jennair.custhelp.com

TWO YEAR LIMITED WARRANTY

WHAT IS COVERED WHAT IS NOT COVERED

For two years from the date of purchase, when this

major appliance is installed, operated and maintained

according to instructions attached to or furnished with

the product, Jenn-Air brand of Whirlpool Corporation or

Whirlpool Canada LP (hereafter “Jenn-Air”) will pay for

Factory Specified Replacement Parts and repair labor

to correct defects in materials or workmanship that

existed when this major appliance was purchased, or at

its sole discretion replace the product. In the event of

product replacement, your appliance will be warranted

for the remaining term of the original unit's warranty

period.

YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS

LIMITED WARRANTY SHALL BE PRODUCT REPAIR

AS PROVIDED HEREIN. Service must be provided by a

Jenn-Air designated service company. This limited

warranty is valid only in the United States or Canada

and applies only when the major appliance is used in

the country in which it was purchased. This limited

warranty is effective from the date of original consumer

purchase. Proof of original purchase date is required to

obtain service under this limited warranty.

1. Commercial, non-residential, multiple-family use, or use inconsistent with published

user, operator or installation instructions.

2. In-home instruction on how to use your product.

3. Service to correct improper product maintenance or installation, installation not in

accordance with electrical or plumbing codes or correction of household electrical or

plumbing (i.e. house wiring, fuses or water inlet hoses).

4. Consumable parts (i.e. light bulbs, batteries, air or water filters, preservation

solutions, etc.).

5. Defects or damage caused by the use of non-genuine Jenn-Air parts or accessories.

6. Conversion of products from natural gas or L.P. gas.

7. Damage from accident, misuse, abuse, fire, floods, acts of God or use with products

not approved by Jenn-Air.

8. Repairs to parts or systems to correct product damage or defects caused by

unauthorized service, alteration or modification of the appliance.

9. Cosmetic damage including scratches, dents, chips, and other damage to the

appliance finishes unless such damage results from defects in materials and

workmanship and is reported to Jenn-Air within 30 days.

10. Discoloration, rust or oxidation of surfaces resulting from caustic or corrosive

environments including but not limited to high salt concentrations, high moisture or

humidity or exposure to chemicals.

11. Food or medicine loss due to product failure.

12. Pick-up or delivery. This product is intended for in-home repair.

13. Travel or transportation expenses for service in remote locations where an authorized

Jenn-Air servicer is not available.

14. Removal or reinstallation of inaccessible appliances or built-in fixtures (i.e. trim,

decorative panels, flooring, cabinetry, islands, countertops, drywall, etc.) that

interfere with servicing, removal or replacement of the product.

15. Service or parts for appliances with original model/serial numbers removed, altered

or not easily determined.

The cost of repair or replacement under these excluded circumstances shall be

borne by the customer.

DISCLAIMER OF IMPLIED WARRANTIES

IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR IMPLIED WARRANTY OF FITNESS FOR A

PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW. Some states and provinces do not allow

limitations on the duration of implied warranties of merchantability or fitness, so this limitation may not apply to you. This warranty gives you

specific legal rights, and you also may have other rights that vary from state to state or province to province.

DISCLAIMER OF REPRESENTATIONS OUTSIDE OF WARRANTY

Jenn-Air makes no representations about the quality, durability, or need for service or repair of this major appliance other than the representations

contained in this warranty. If you want a longer or more comprehensive warranty than the limited warranty that comes with this major appliance,

you should ask Jenn-Air or your retailer about buying an extended warranty.

LIMITATION OF REMEDIES; EXCLUSION OF INCIDENTAL AND CONSEQUENTIAL DAMAGES

YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS LIMITED WARRANTY SHALL BE PRODUCT REPAIR AS PROVIDED HEREIN. JENN-AIR

SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some states and provinces do not allow the exclusion or limitation

of incidental or consequential damages, so these limitations and exclusions may not apply to you. This warranty gives you specific legal rights, and

you also may have other rights that vary from state to state or province to province.

SÉCURITÉ DE LA HOTTE DE CUISINIÈRE

Risque possible de décès ou de blessure grave si vous ne

suivez pas immédiatement les instructions.

Risque possible de décès ou de blessure grave si vous

ne suivez pas les instructions.

Tous les messages de sécurité vous diront quel est le danger potentiel et vous disent comment réduire le risque de blessure et

ce qui peut se produire en cas de non-respect des instructions.

Votre sécurité et celle des autres est très importante.

Nous donnons de nombreux messages de sécurité importants dans ce manuel et sur votre appareil ménager. Assurez-vous de

toujours lire tous les messages de sécurité et de vous y conformer.

AVERTISSEMENT

DANGER

Voici le symbole d’alerte de sécurité.

Ce symbole d’alerte de sécurité vous signale les dangers potentiels de décès et de blessures graves à vous

et à d’autres.

Tous les messages de sécurité suivront le symbole d’alerte de sécurité et le mot “DANGER” ou

“AVERTISSEMENT”. Ces mots signifient :

Avertissements de la proposition 65 de l'État de Californie :

AVERTISSEMENT : Ce produit contient au moins un produit chimique connu par l’État de Californie pour être à l’origine de

cancers.

AVERTISSEMENT : Ce produit contient au moins un produit chimique connu par l’État de Californie pour être à l’origine de

malformations et autres déficiences de naissance.

IMPORTANTES INSTRUCTIONS DE SÉCURITÉ

LIRE ET CONSERVER CES INSTRUCTIONS

AVERTISSEMENT : POUR RÉDUIRE LE RISQUE

D'INCENDIE, CHOC ÉLECTRIQUE OU DOMMAGES

CORPORELS, RESPECTER LES INSTRUCTIONS

SUIVANTES :

■ Utiliser cet appareil uniquement dans les applications

envisagées par le fabricant. Pour toute question, contacter

le fabricant.

■ Avant d'entreprendre un travail d'entretien ou de nettoyage,

interrompre l'alimentation de la hotte au niveau du tableau

de disjoncteurs, et verrouiller le tableau de disjoncteurs

pour empêcher tout rétablissement accidentel de

l'alimentation du circuit. Lorsqu'il n'est pas possible de

verrouiller le tableau de disjoncteurs, placer sur le tableau

de disjoncteurs une étiquette d'avertissement proéminente

interdisant le rétablissement de l'alimentation.

■ Tout travail d'installation ou câblage électrique doit être

réalisé par une personne qualifiée, dans le respect des

prescriptions de tous les codes et normes applicables, y

compris les codes du bâtiment et de protection contre les

incendies.

■ Ne pas faire fonctionner un ventilateur dont le cordon ou la

fiche est endommagé(e). Jeter le ventilateur ou le retourner

à un centre de service agréé pour examen et/ou réparation.

■ Une source d'air de débit suffisant est nécessaire pour le

fonctionnement correct de tout appareil à gaz (combustion

et évacuation des gaz à combustion par la cheminée), pour

qu'il n'y ait pas de reflux des gaz de combustion. Respecter

les directives du fabricant de l'équipement de chauffage et

les prescriptions des normes de sécurité - comme celles

publiées par la National Fire Protection Association (NFPA)

et l'American Society for Heating, Refrigeration and Air

Conditioning Engineers (ASHRAE), et les prescriptions des

autorités réglementaires locales.

■ Lors des opérations de découpage et de perçage dans un

mur ou un plafond, ne pas endommager les câblages

électriques et les canalisations qui peuvent s’y trouver.

■ Les ventilateurs d'évacuation doivent toujours décharger

l'air à l'extérieur.

MISE EN GARDE : Cet appareil est conçu uniquement

pour la ventilation générale. Ne pas l'utiliser pour l'extraction

de matières ou vapeurs dangereuses ou explosives.

MISE EN GARDE : Pour minimiser le risque d'incendie

et évacuer adéquatement les gaz, veiller à acheminer l'air

aspiré par un conduit jusqu'à l'extérieur - ne pas décharger

l'air aspiré dans un espace vide du bâtiment comme une

cavité murale, un plafond, un grenier, un vide sanitaire ou

un garage.

AVERTISSEMENT : POUR RÉDUIRE LE RISQUE

D'INCENDIE, UTILISER UNIQUEMENT DES CONDUITS

MÉTALLIQUES.

AVERTISSEMENT : POUR MINIMISER LE RISQUE

D'UN FEU DE GRAISSE SUR LA CUISINIÈRE :

■ Ne jamais laisser un élément de surface fonctionner à

puissance de chauffage maximale sans surveillance. Un

renversement/débordement de matière graisseuse pourrait

provoquer une inflammation et la génération de fumée.

Utiliser une puissance de chauffage moyenne ou basse

pour le chauffage d'huile.

■ Veiller à toujours faire fonctionner le ventilateur de la hotte

lors de la cuisson avec une puissance de chauffage élevée

ou lors de la cuisson d'un mets à flamber (à savoir crêpes

Suzette, cerise jubilée, steak au poivre flambé).

■ Nettoyer fréquemment les ventilateurs d'extraction. Veiller à

ne pas laisser la graisse s'accumuler sur les surfaces du

ventilateur ou des filtres.

■ Utiliser toujours un ustensile de taille appropriée. Utiliser

toujours un ustensile adapté à la taille de l'élément

chauffant.

AVERTISSEMENT : POUR RÉDUIRE LE RISQUE DE

DOMMAGES CORPORELS APRÈS LE DÉCLENCHEMENT

D'UN FEU DE GRAISSE SUR LA CUISINIÈRE, APPLIQUER

LES RECOMMANDATIONS SUIVANTES :

■ Placer sur le récipient un couvercle bien ajusté, une tôle à

biscuits ou un plateau métallique POUR ÉTOUFFER LES

FLAMMES, puis éteindre le brûleur. VEILLER À ÉVITER

LES BRÛLURES. Si les flammes ne s'éteignent pas

immédiatement, ÉVACUER LA PIÈCE ET APPELER LES

POMPIERS.

■ NE JAMAIS PRENDRE EN MAIN UN RÉCIPIENT

ENFLAMMÉ - vous risquez de vous brûler.

■ NE PAS UTILISER D'EAU, ni un torchon humide - ceci

pourrait provoquer une explosion de vapeur brûlante.

■ Utiliser un extincteur SEULEMENT si :

– Il s'agit d'un extincteur de classe ABC, dont on connaît le

fonctionnement.

– Il s'agit d'un petit feu encore limité à l'endroit où il s'est

déclaré.

– Les pompiers ont été contactés.

– Il est possible de garder le dos orienté vers une sortie

pendant l'opération de lutte contre le feu.

Recommandations tirées des conseils de sécurité en cas

d'incendie de cuisine publiés par la NFPA.

■ AVERTISSEMENT : Pour réduire le risque d'incendie

ou de choc électrique, ne pas utiliser ce ventilateur avec un

quelconque dispositif de réglage de la vitesse à semi-

conducteurs.

La page charge ...

Jenn-Air JXI8936DS Guide d'installation

Marque: Jenn-Air

Modèle: JXI8936DS

Catégorie: Hottes

Taper: Guide d'installation

Télécharger le PDF

rapport

dans d''autres langues

English: Jenn-Air JXI8936DS Installation guide

Jenn-Air JXI8936DS Guide d'installation

Jenn-Air JXI8936DS Guide d'installation

dans d''autres langues

Documents connexes

Autres documents