Sanyo LCD55L4 Manuel utilisateur

Marque: Sanyo

Modèle: LCD55L4

Catégorie: Équipement musical supplémentaire

Taper: Manuel utilisateur

Instruction manual

Manuel de l’utilisateur

LCD55L4

55” Stereo HDTV LCD television with

LED edge-lighting and USB socket

Téléviseur ACL stéréo haute définition de 55 po

avec panneau lumineux à DEL et connecteur USB

Help line / Ligne d’assistance : 1-800-263-2244

Monday to Friday 9am to 5pm (Eastern)

Du lundi au vendredi, de 9 h à 17 h (heure de l’Est)

http://ca.sanyo.com

1080p HDTV LCD

TVHD 1080p ACL

All manuals and user guides at all-guides.com

all-guides.com

Need help? http://ca.sanyo.com 1-800-263-2244

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators,

heat registers, stoves, or other apparatus (including

amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or

grounding-type plug. A polarized plug has two blades with

one wider than the other. A grounding-type plug has two

blades and a third grounding prong. The wide blade or the

third prong are provided for your safety. If the provided

plug does not fit fully into your outlet, consult an electri-

cian for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or

pinched particularly at plugs, convenience receptacles,

and the point where they exit from the apparatus.

11. Only use attachments/accessories specified by the

manufacturer.

12. Use only with the cart, stand, tripod,

bracket, or table specified by the manu-

facturer, or sold with the apparatus.

When a cart is used, use caution when

moving the cart/apparatus combination

to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when

unused for long periods of time.

14. Refer all servicing to qualified service personnel.

Servicing is required when the apparatus has been

damaged in any way, such as power-supply cord or plug

is damaged, liquid has been spilled or objects have fall-

en into the apparatus, the apparatus has been exposed

to rain or moisture, does not operate normally, or has

been dropped.

15. If an outside antenna is connected to the television

equipment, be sure the antenna system is grounded so

as to provide some protection against voltage surges

and built up static charges. In the U.S. Selection 810-21

of the National Electrical Code provides information with

respect to proper grounding of the mast and supporting

structure, grounding of the lead-in wire to an antenna

discharge unit, size of grounding conductors, location of

antenna discharge unit, connection to grounding elec-

trodes, and requirements for the grounding electrodes.

16. An outside antenna system should not be located in the

vicinity of overhead power lines or other electrical light

or power circuits, or where it can fall into such power

lines or circuits. When installing an outside antenna

system, extreme care should be taken to keep from

touching such power lines or circuits as contact with

them might be fatal.

EXAMPLE OF ANTENNA GROUNDING ACCORDING

TO NATIONAL ELECTRICAL CODE, ANSI/NFPA 70

“Note to CATV system installer:

This reminder is provided to call the CATV system installer’s

attention to Article 820-40 of the NEC that provides guidelines for

proper grounding and, in particular, specifies that the cable

ground shall be connected to the grounding system of the build-

ing, as close to the point of cable entry as practical.”

17. Wall or Ceiling Mounting—The product should be

mounted to a wall or ceiling only as recommended by

the manufacturer.

18. Apparatus shall not be exposed to dripping or splashing

and no objects filled with liquids, such as vases, shall be

placed on the apparatus.

19. When the MAINS plug is used as the disconnect device,

the disconnect device shall remain readily operable.

CAUTION

RISK OF ELECTRIC SHOCK DO NOT OPEN!

AUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR

BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERV-

ICE PERSONNEL.

THIS SYMBOL INDICATES THAT DANGEROUS VOLTAGE CONSTITUTING A

ISK OF ELECTRIC SHOCK IS PRESENT WITHIN THIS UNIT.

THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT OPERATING AND

AINTENANCE INSTRUCTIONS IN THE LITERATURE ACCOMPANYING THIS

UNIT.

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO

RAIN OR MOISTURE.

IMPORTANT SAFETY INSTRUCTIONS

All manuals and user guides at all-guides.com

Need help? http://ca.sanyo.com 1-800-263-2244

This symbol on the nameplate means

the product is Listed by Underwriter’s

Laboratories Inc. It is designed and

manufactured to meet rigid U.L. safety

standards against risk of fire, casualty

and electrical hazards.

FCC INFORMATION

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15

of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by turning the equipment off and on,

the user is encouraged to try to correct the interference by one or more of the following measures:

– Reorient or relocate the receiving antenna.

– Increase the separation between the equipment and receiver.

– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

– Consult the dealer or an experienced radio/TV technician for help.

CAUTION: FCC Regulations state that improper modifications or unauthorized changes to this unit may void

the user’s authority to operate the unit.

TRADEMARKS

PC RESOLUTION CHART

This Class B digital apparatus complies with Canadian

ICES-003.

As an Energy Star

Partner, SANYO

Manufacturing Corporation has deter-

mined that this product meets the

Energy Star

guidelines for energy

efficiency.

ENERGY STAR

Manufactured under license from Dolby Laboratories.

“Dolby” is a trademark of Dolby Laboratories.

HDMI, the HDMI Logo and High-

Definition Multimedia Interface are

trademarks or registered trademarks

of HDMI Licensing LLC in the United

States and other countries.

All manuals and user guides at all-guides.com

Need help? http://ca.sanyo.com 1-800-263-2244

CONTENTS

Thank you for choosing SANYO.

Please read all instructions to obtain

maximum benefit of your product.

IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . 2

FCC INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

TRADEMARKS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

PC RESOLUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

PROTECTING THE SCREEN . . . . . . . . . . . . . . . . . . . . . . . . .4

POSITIONING THE HDTV . . . . . . . . . . . . . . . . . . . . . . . . . . .5

STAND REMOVAL / WALL MOUNTING . . . . . . . . . . . . . . .5

GETTING STARTED—

Remote Control Battery Installation . . . . . . . . . . . . . . . .5

Antenna Connections for off-air or cable . . . . . . . . . . .5

HDTV INPUT/OUTPUT REFERENCE . . . . . . . . . . . . . . . . . . .6

A/V CONNECTIONS (SIDE PANEL) . . . . . . . . . . . . . . . . . . .7

A/V CONNECTIONS (BACK PANEL) . . . . . . . . . . . . . . . . . .8

POWER CONNECTION / INITIAL CHANNEL SEARCH . . .9

REMOTE CONTROL OPERATION . . . . . . . . . . . . . . . . . . . .10

ON-SCREEN MENU OPERATION—

Channel / Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Channel Search . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Channel Scan Memory . . . . . . . . . . . . . . . . . . . . . . .11

Input Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Video3 Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

HDMI Linking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Menu Language . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Digital Caption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Energy Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

Clock Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Motion Sync . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

V-Chip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Picture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16

Sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

PC CONNECTIONS & MENU OPERATION . . . . . . . . . . . .18

PHOTO VIEWER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

PROTECTING THE SCREEN

CAUTION: The screen can be damaged if it is not

maintained properly.

•

Do not use hard objects such as hard cloth or

paper to clean the screen.

•

Do not use excessive pressure when cleaning

the screen; excessive pressure can cause

permanent discoloration or dark spots.

•

NEVER spray liquids on the screen.

HANDLING PRECAUTIONS

•

Handle by the cabinet only.

•

Never touch the screen when handling.

•

Handling damage is not covered under warranty.

POSITIONING THE HDTV

•

Always use a firm and flat surface when

positioning your HDTV.

•

Do not position the unit in a confined area.

•

Allow adequate space for proper ventilation.

SPECIFICATIONS

Power Requirement: Source: AC 120V, 60Hz

AC Power Consumption: Weight:

195 watts 75 lbs.

Dimensions:

MODEL WIDTH HEIGHT DEPTH

LCD55L4 51.2 34.5 10.9

w/o stand 32.3 2.4

NOTE: Dimensions are in inches

Please read before

operating your HDTV!

“The Amercian Academy of Pediatrics discourages

television viewing for children younger than two

years of age”

All manuals and user guides at all-guides.com

Need help? http://ca.sanyo.com 1-800-263-2244

Remove the two (2) screws holding the stand

base cover and carefully dislodge.

STAND REMOVAL AND WALL

MOUNTING (OPTIONAL)

Tools Needed: Phillips screwdriver

IMPORTANT NOTE: Place HDTV face down

on a padded or cushioned flat surface to

protect the screen and finish.

Wall mounting of the HDTV must be performed

by a skilled person.

GETTING STARTED

Install two (2) “AAA” batteries in the remote

control. (Not included)

To ensure safe operation, please observe the

following precautions:

• Replace both batteries at the same time. Do not use a

new battery with a used battery.

• There’s a risk of explosion if a battery is replaced by

an incorrect type.

• Do not expose the Remote Control unit to moisture

or heat.

• Be sure to match the “+” and “

–” signs on the

batteries with marks inside the remote control.

ANTENNA CONNECTION FOR

OFF-AIR SIGNALS OR CABLE

ANTENNA

CABLE

ANALOG / DIGITAL

ANTENNA IN

BATTERY INSTALLATION

Hook up your antenna or your cable service to

the HDTV’s ANT terminal with the use of a 75

OHM coaxial cable.

NOTE: Keep your indoor antenna at least 3 ft. away

from the television set and any other electronic

equipment.

The tuner in this HDTV can receive:

• Digital and Analog off air signals from an antenna

• Analog or ClearQAM cable channels from a direct

Cable TV connection.

Remove the four (4) screws securing the

stand base to the HDTV. CAUTION: Hold the

stand firmly as you remove the last screw.

Use the screws that are threaded into the four

(4) inserts on the back of your HDTV to secure

it to an appropriate wall mounting kit.

VESA standard interface: 400 x 400

Mounting screws measurements:

M6 (6mm) Diameter, Length—12mm (maximum)

NOTE: Wall mounting kit is not included.

All manuals and user guides at all-guides.com

Need help? http://ca.sanyo.com 1-800-263-2244

S-Video Input (VIDEO1)

NOTE: An S-Video connection will override a connection to

the Video1 (yellow) input jack.

Composite AV Input (VIDEO1) – Yellow (Video),

plus white and red (Audio) input jacks.

Component AV Input (VIDEO2) – Green (Y), blue

(Pb), and red (Pr) Video inputs plus the white and

red Audio inputs.

Stereo Audio Out (L/R) Jacks

HDMI (INPUT2 & 3) – An all digital AV interface

accepting uncompressed video signals up to

1080p for the best picture possible.

Analog / Digital Antenna Input – Connect a 75 OHM

cable from an antenna or direct Cable service.

Digital Audio Output (Coaxial)

AV Component Input (VIDEO3) – Green (Y), blue

(Pb), and red (Pr) Video inputs plus the white and

red Audio inputs.

NOTE: A Composite connection is possible via VIDEO

INPUT3 using the Y (VIDEO) jack and the L/R audio

jacks. (See Video 3 Setting on page 12.)

PC Input and Stereo Audio (Mini)

• MONITOR RGB (D-SUB)

• AUDIO R/L (Stereo Mini Jack)

NOTE: See page 18 for proper PC hookup and setup.

GETTING STARTED

HDTV INPUT/OUTPUT REFERENCE

USB Input

View pictures stored in a USB flash drive.

HDMI (INPUT1)

An all digital AV interface that can accept

uncompressed video signals up to 1080p

for the very best picture possible.

NOTE: A DVI connection is possible via the HDMI

INPUT1 (DVI) using an appropriate adapter

and the VIDEO3 Audio jacks for sound output.

ETHERNET Port

For Service use only.

HDTV BACK PANEL

HDTV

SIDE PANEL

All manuals and user guides at all-guides.com

all-guides.com

Need help? http://ca.sanyo.com 1-800-263-2244

GETTING STARTED

AUDIO / VIDEO CONNECTIONS (SIDE PANEL)

DVD PLAYER

(or similar device)

MULTICHANNEL RECEIVER

(or home theater system)

NOTE: Audio/Video cables

are not supplied

COMPONENT connections will accept SDTV,

EDTV and HDTV video signals. Use them for great

image quality from digital devices such as a DVD

player or Video Game system.

Match your digital device’s Component output jacks

to either of the two (2) Component input jack sets

(VIDEO2 or VIDEO3) on your HDTV.

USB FLASH DRIVE

USB input jack is used to con-

nect a USB mass storage device

to display digital images on

your HDTV. (JPEG format only.)

DVI

HDMI (DVI) INPUT1 can be used to hookup a DVI

device with the use of an appropriate DVI to HDMI

cable or adapter. VIDEO3 Audio in L/R jacks need to

be hooked up to the DVI device as well

NOTE: HDMI INPUT1 may also be used to hookup any digital

device with an HDMI output, without the use of the L/R

audio jacks.

Digital Audio Output is used to output the HDTV’s

Audio through your home theater system.

Hook up the HDTV’s Digital Audio Output to your

home theater system’s input with the use of a

phono-type Digital Audio cable.

DVD PLAYER

(or similar device)

All manuals and user guides at all-guides.com

Need help? http://ca.sanyo.com 1-800-263-2244

GETTING STARTED

AUDIO / VIDEO CONNECTIONS (BACK PANEL)

VCR

(or analog device)

STEREO AMPLIFIER

COMPOSITE connections are used to hookup

your analog equipment such as a VCR or an older

DVD player.

Hook up you analog device’s yellow video output

jack and corresponding audio output jacks to the

HDTV’s Video Input 1 composite jacks.

NOTE: Always match the color of your device’s output jack,

the connector and the HDTV’s input jack.

S-Video jack may be used instead of the yellow

Composite video input with the use of an S-Video

cable connected from your device’s S-Video out-

put to the HDTV’s S-Video input.

SATELLITE RECEIVER

(or similar device)

Audio Output L/R are used to hookup an external

stereo Amplifier. Connect your home stereo’s

input jacks to the HDTV’s Audio Output jacks with

a pair of audio red and white connectors.

NOTE: Do not connect external speakers directly to the

HDTV.

Use HDMI INPUT1, 2 & 3 to hookup HD digital

devices such as a Blu-ray player, HD Cable Box,

HD Satellite Receiver or Video-game System.

Connect your digital device’s HDMI output to any

of the three (3) HDMI inputs on your HDTV with

the use of an HDMI cable.

HDMI

All manuals and user guides at all-guides.com

Need help? http://ca.sanyo.com 1-800-263-2244

TURN ON TV (PRESS POWER BUTTON)

Wait for on-screen instructions to set an

Initial Energy Saving Mode, and perform an

Initial Channel/Signal Search.

PLUG IN AC POWER CORD

120V AC, 60Hz

GETTING STARTED (CONTINUED)

INITIAL CHANNEL SEARCH

Before proceeding, please make sure to hook up

your antenna or cable connection and all AV

equipment correctly to your HDTV.

Press the CH key to perform a channel

search from an Antenna or a direct Cable

connection, and a signal search from devices

hooked up to the HDTV’s AV input jacks.

AV INPUT SELECTION

Press the INPUT key to select the correct AV

input for the video source you wish to watch.

TV SET LOCATION SELECTION:

Select “Home Mode” by pressing the CH key to set

the HDTV’s backlight to an Energy Star qualified level,

or select “Store Mode” by pressing CH to set the

backlight to a retail display level.

CHANNEL AND AV SIGNAL SEARCH:

CHANNEL AND SIGNAL SETUP SCREEN

The final setup screen displays analog and digital

channels found as well as AV inputs detected. Pressing

the CH key finalizes the setup process.

NOTE: To repeat the initial setup process press VOL.

Press the CH key if you wish to access an

on screen trouble shooting guide.

NOTE: On screen help is also accessible via the

main menu.

ON SCREEN HELP (OPTIONAL)

INITIAL CHANNEL/SIGNAL SEARCH

SETUP SCREEN

CHANNEL SEARCH PROGRESS SCREEN

INITIAL ENERGY SAVING

MODE SCREEN

CHANNEL/SIGNAL LIST SCREEN

All manuals and user guides at all-guides.com

Need help? http://ca.sanyo.com 1-800-263-2244

REMOTE CONTROL OPERATION

• PIX SHAPE Key—Cycles through the available

aspect ratios. The different settings either

stretch, zoom, or fill the image on your screen.

Bars may appear on top and bottom of your

screen (or on left and right sides) depending on

the broadcasted signal or program.

NOTE: Pix6-7 are setup as Pix1-2 in PC mode. Use of

Pix6-7 in TV mode is not recommended.

• MENU—Displays or hides the on-screen menu.

• HELP—Displays on-screen Help menu.

• INFO Key—Displays the Channel Information

banner.

• EXIT Key—Exits the on-screen menu.

• Cursor  (UP)  (DOWN) keys—Move the on-

screen cursor up and down.

• Cursor t (LEFT) u (RIGHT) keys—Move the on-

screen cursor left and right.

• ENTER Key—Set or select the highlighted option

on the screen.

The PLAY, PAUSE, STOP, REW, FF, W, T, CAMERA,

and XACTI MENU keys control playback features

on a SANYO Xacti digital camera when the HDMI-

CEC feature has been activated on both the HDTV

and the Xacti camera (see HDMI Linking feature

on page 12.)

NOTE: These playback keys may or may not react with

other devices other than the Xacti camera.

• POWER Key—Turns your HDTV On or Off.

• ECO Key—Modifies the Energy Saver level (see

page 13.)

• AUDIO Key—Selects the desired Audio mode.

Stereo, Mono, or SAP (when available.)

• ON TIMER Key—Displays the current switch on

time (see Clock Timer on page 14.)

• CAPTION Key—Cycles through the available

Caption modes.

• RESET Key—Pressing it twice restores your

HDTV to its factory settings. All user customized

settings will be cleared.

• SLEEP Key—Displays the “Off” Timer. While Off

Timer is on-screen, press the “0” key to Set the

amount of time (in 30 minute increments) at

which the HDTV will turn off.

• PICTURE Key—Cycle through the picture modes.

• SOUND Key—Cycle through the sound modes.

• NUMERICAL Keys—Select channels directly.

NOTE: For channels 100 and up, press and hold the

first number, then enter the remaining two numbers.

• “

––

” (sub ch) key —Allows for the direct selec-

tion of digital subchannels. For example: to

select channel 39.1 press the

3, 9,

––

, and 1 keys.

• INPUT Key—Selects the video source to view.

Holding down the key displays the Input List.

• Volume

––

keys—Increases or decreases the

audio level.

• Channel keys—Scan through the channels

in the memory database.

• MUTE Key—Mute or restore the sound.

• RECALL Key—Switch between current channel

and last selected channel.

• DYN VOL Key—Select sound enhancement

feature.

• USB Key—Selects the USB input directly.

All manuals and user guides at all-guides.com

CHANNEL / INPUT ____________

Need help? http://ca.sanyo.com 1-800-263-2244

Auto – Searches the detected mode, Cable or Air.

Cable – Searches for analog and unscrambled

(ClearQAM) digital cable channels.

Air (Antenna) – Searches for analog and digital off-air

channels.

Digital Add-On – Searches digital off-air channels

adding newly found digital channels to the channel

map database.

Channel Search

Display the On Screen menu and use the

CURSOR  keys to select Channel / Input.

Press ENTER.

NOTE: Digital Add-On option is not available when the cur-

rent mode is Cable.

ON-SCREEN MENU OPERATION

Channel Scan Memory lists all Analog and Digital

channels found. It also lists Analog channels that were

not found, which can be added.

Use the CURSOR  keys to move the channel select

bar through all enabled and disabled channels, or use

the CH  keys to skip all disabled channels.

Press ENTER to enable or disable the selected channel.

Channel Scan Memory

IMPORTANT FACT: This HDTV maintains only one database of

digital channels. Therefore, when you search for cable chan-

nels, the database of antenna digital channels will be deleted.

You will only be able to receive those ClearQAM channels your

cable company provides.

Input Setting

CHANNEL SCAN MEMORY SCREEN

INPUT SETTING SCREEN

MAIN MENU SCREEN

CHANNEL SETTING SCREEN

Input Setting feature allows the removal of unused

inputs from the AV input loop.

Use the CURSOR  keys to select an AV input. Press

ENTER to disable (uncheck) or enable (check) the high-

lighted input.

NOTE: At least one input must and will remain enabled.

:Skip is for reference only.

All manuals and user guides at all-guides.com

all-guides.com

Need help? http://ca.sanyo.com 1-800-263-2244

ON-SCREEN MENU OPERATION

Use this feature to establish either a Component or

Composite connection to the VIDEO INPUT 3 jacks on

your HDTV.

Use the CURSOR  keys to select the type of hook up

that will be used in the Video3 input.

Press ENTER, a blue mark will appear next to the

selected option.

Video3 Setting

With a SANYO Xacti Digital

Video/Movie Camera hooked up to your

HDTV’s HDMI input, setting the HDMI-

CEC Function to ON enables you the use

of keys on your GXEA remote to operate

your Xacti camera.

Xacti-LINK

NOTE: The HDMI-CEC function of the Xacti must also be

turned ON to enable the Xacti-Link.

NOTE: Designed for use with a SANYO Xacti Digital

Video/Movie Camera, and may not support all HDMI-

CEC functions of other equipment.

Use the HDMI-CEC Function to enable or disable all

available CEC functions.

HDMI Power ON Sync and Power OFF Sync enable

specific features including the automatic power ON

process and power OFF process.

HDMI Linking

HDMI LINKING SCREEN

VIDEO3 SETTING SCREEN

CHANNEL SETTING ___________

All manuals and user guides at all-guides.com

Need help? http://ca.sanyo.com 1-800-263-2244

MENU LANGUAGE SCREEN

Digital Caption

SETUP _________________________

Display the On Screen menu and use the

CURSOR  keys to select Setup.

Press ENTER.

Captioning is textual information transmitted along

with the picture and sound. Turning Captioning ON (by

pressing the CAPTION key during normal TV viewing)

causes the HDTV to open these captions (digital or

analog) and superimpose them on the screen.

NOTE: Local broadcasters decide which caption signals to

transmit.

Use the CURSOR  and tu keys to modify Font,

Background, and Foreground of digital caption text.

Choose the language in which you On Screen menus

will be displayed.

• English

• Español

• Français

Press ENTER on the desired language.

ON-SCREEN MENU OPERATION

Energy Setting

Menu Language

Use the Energy Saver and Light Sensor features found

under Energy Setting to lower power comsumption by

controlling the LED backlight brightness levels.

Energy Saver – This settings control the LCD backlight

brightness to reduce power consumption.

• Level 1: Energy Saver feature is off.

• Level 2: Low power consumption.

• Level 3: Lowest power consumption.

Press ENTER on the desired level.

NOTE: ECO key may also be used as a shortcut to modify the

Energy Saver settings.

ENERGY SAVER SCREEN

MAIN MENU SCREEN

DIGITAL CAPTION SCREEN

All manuals and user guides at all-guides.com

Need help? http://ca.sanyo.com 1-800-263-2244

This feature allows you to set a Current Time for your

HDTV and enable a Switch On Time for the HDTV to

turn on at a specific time of day.

When On Timer Function is set to ON, the TV will

automatically turn on at the previously set Switch on

Time.

Clock Timer

CLOCK TIMER SCREEN

ON-SCREEN MENU OPERATION

Your HDTV has a refresh rate of 120

Hz, it basically means that it “redraws”

the image on the screen twice as often

than a common 60 Hz refresh rate TV

would, allowing for less blur in scenes

with fast motion.

• On – Takes full advantage of your TV’s refresh rate

capabilities for the best picture quality.

• Off – Disables the Motion Sync. feature.

NOTE: Even with Motion Sync set to Off, your HDTV still

displays all images at a 120 Hz refesh rate.

Motion Sync

MOTION SYNC SCREEN

LIGHT SENSOR SCREEN

Light Sensor – Detects ambient room light brightness

and uses that reading to control the panel brightness

level and picture parameters to reduce the HDTV’s

power consumption.

NOTE: When room lighting is dark, the panel brightness

and/or the picture setting parameters such as bright-

ness and cotrast are lowered. When room lighting is

bright, parameters are affected opposite.

All manuals and user guides at all-guides.com

Need help? http://ca.sanyo.com 1-800-263-2244

SETUP ________________________

ON-SCREEN MENU OPERATION

Use this feature to automatically block programs with

content you deem as inappropriate for viewing by

your children.

NOTE: This feature is designed to comply with the United

States of America’s FCC V-Chip regulations. Therefore,

it may not function with broadcasts that originate in

other countries.

ADJUSTING THE V-CHIP RATINGS

Select ON and press ENTER.

Select Adjust (Standard) and press ENTER.

Use the CURSOR   and tu keys to navigate and

the ENTER key to Block or Unblock a selected rating. A

lock symbol will appear beside the selected rating

option indicating that it is blocked

NOTE: Blocking a rating will automatically block all higher

ratings. Unblocking a rating automatically unblocks

all lower ratings.

V – Chip (Parental Control)

ADVANCED V-CHIP SYSTEM (RRT5)

RRT5 (V-Chip Regional Ratings 5) is an advanced V-Chip

ratings system for digital channels that are received

with an antenna.

When the HDTV detects compatible RRT5 data, it’s

downloaded & stored in memory, and the Setup

V-Chip screen is then modified to show the Adjust

(Advanced) option.

Use the CURSOR   and tu keys to highlight the

different options, and use the ENTER key to block or

unblock the selected rating.

MORE INFORMATION

Additional information about MPAA (Motion Picture

Association of America) and V-Chip rating can be

found at: www.mpaa.org and www.v-chip.org,

respectively.

NOTE:There may be more ratings than can be displayed on

one screen. When vertical scroll bars appear, press

CURSOR  to gain access to the additional ratings.

V-CHIP SETUP SCREEN

ADJUST (STANDARD) SCREEN

ADJUST (ADVANCED) SCREEN

V-CHIP SETUP SCREEN WITH ADJUST

(ADVANCED) OPTION

All manuals and user guides at all-guides.com

Need help? http://ca.sanyo.com 1-800-263-2244

PICTURE ____________________

ON-SCREEN MENU OPERATION

You may choose between Vivid, Mild, , and Standard,

which have predetermined fixed picture parameter

values, or choose the Manual option for customized

personal settings.

NOTE: Each AV input can have its own picture mode (pre-

determined or manual.) Current input’s selected

option is indicated by a blue marker.

Manual parameters to adjust include:

•

Color

•

Tint

•

Contrast

•

Brightness

•

Sharpness

•

Dynamic Contrast

The Detailed Setting option allows for the adjustment

of 7 additional parameters such as:

•

Signal Balancer

•

Noise Reduction

•

White Balance

•

Vertical Sharpness

•

Edge Enhancer

•

H-Size

•

V-Size

NOTE: Default Picture option returns all picture parameters to

their original factory settings.

MANUAL PICTURE SETTINGS

NOTE: CURSOR  keys select the next/previous parame-

ter without returning to the previous menu screen.

Display the On Screen menu and use the

CURSOR  keys to select Picture. Press ENTER.

Use the CURSOR  keys to highlight the picture

parameter you wish to adjust. Press the ENTER key to

enter the value adjustment screen. Modify the selected

parameter’s value by pressing the CURSOR tu keys.

ADJUSTING A PICTURE SETTING

Once adjustments are complete, press the EXIT key to

return to normal TV viewing.

MAIN MENU SCREEN

PICTURE SCREEN (MANUAL)

PARAMETER SELECTION SCREEN

VALUE ADJUSTMENT SCREEN EXAMPLES

All manuals and user guides at all-guides.com

all-guides.com

Need help? http://ca.sanyo.com 1-800-263-2244

SOUND _____________________

Display the On Screen menu and use the

CURSOR  keys to select Sound. Press ENTER.

ON-SCREEN MENU OPERATION

Choose an option for your sound settings:

Auto – Sound settings are linked to the current Picture

option and parameters are adjusted accordingly.

Dynamic, Mild, Standard – 3 different predetermined

sound parameters not linked with any Picture option.

MANUAL SOUND SETTINGS

The Manual option provides different parameters that

can be personally adjusted:

•

Bass

•

Treble

•

Detailed Setting

– 4-Band Equalizer: Personalize audio highs and lows.

NOTE: Default Sound option returns all sound parameters to

their original factory settings.

NOTE:

CURSOR  keys select the next/previous parame-

ter without returning to the previous menu screen.

Use the CURSOR  keys to highlight the sound

parameter you wish to adjust. Press the ENTER key to

enter the value adjustment screen. Modify the selected

parameter’s value by pressing the CURSOR tu keys.

ADJUSTING A SOUND SETTING

Once adjustments are complete, press the EXIT key to

return to normal TV viewing.

MAIN MENU SCREEN

MANUAL PARAMETER SCREEN

DETAILED SETTING SCREEN

VALUE ADJUSTMENT SCREEN EXAMPLES

All manuals and user guides at all-guides.com

Need help? http://ca.sanyo.com 1-800-263-2244

PC OR LAPTOP

HDTV SIDE PANEL

RGB Monitor

cable

Stereo mini

audio cable

SANYO recommends using

a monitor cable that

includes a Ferrite Core.

PC INPUT

PC Setting

Auto Adjustment – Automatically adjusts display

position, dot clock and phase.

Dot Clock – Adjust the Dot frequency to match

your computer’s Dot frequency.

Phase – Adjust this parameter when the picture

appears to flicker or is blurred.

H-Position – Move the image horizontally

V-Position – Move the image vertically

Power Saving – Enable the HDTV to turn to

Standby Mode when computer is not in use.

PC Picture and Sound

Standard – Sets predetermined values to the

Picture or Sound parameters.

Manual – Adjust Contrast, Brightness, and Color

Temperature screen settings, and the Bass and

Treble audio settings.

NOTE: These settings do not affect normal TV viewing.

Laptop Display

When using your SANYO HDTV to display a

Laptop’s screen display, holding down the Fn (or

FN) key while pressing the appropriate function

key (F5, F7, F8, etc) should cycle through different

display modes between the laptop and the HDTV.

Modes may include displaying only on the laptop

screen, on both the laptop and the HDTV, or

displaying only on the HDTV.

NOTE: Fn key and function key symbols on the laptop’s

keyboard may vary from one brand to another.

Hold down and press

Before connecting any cables, disconnect the

AC power cords of both the HDTV and PC from

the AC outlets.

Power on the HDTV and any other peripheral

equipment before powering on the computer.

To avoid an “Out of Range” condition please set

your PC’s output resolution to one compatible with

your HDTV. See PC Resolution chart on page 3.

DVI OUTPUT

JACK

RGB OUTPUT

JACK

Use your HDTV as a computer monitor by hooking

up your PC or Laptop to the TV with the use of an

appropriate monitor cable (not included.)

PC PICTURE AND SOUND SCREENS

PC SETTING SCREEN

NOTE: If computer has only DVI Output, a DVI to RGB

adapter will be required, or, a DVI to HDMI cable

and RCA audio cables (see HDMI (DVI) INPUT1 on

page 7.)

All manuals and user guides at all-guides.com

Need help? http://ca.sanyo.com 1-800-263-2244

PHOTO VIEWER __________________

USING THE PHOTO VIEWER

Press ENTER on a thumbnail photo to enable the

Rotate, Full View and Start Slideshow functions.

Once in Full View mode:

Use the CURSOR tu keys to change picture.

Press ENTER to show the full view options menu.

SLIDE SHOW

In the Slideshow Setup menu you may turn the Shuffle

and Quick Change options ON or OFF.

Press ENTER on Start Slideshow from the Thumbnail

View Screen or from the full view options menu to start

the slideshow from the current picture.

JPEG VIEWER USB MENU

Press MENU when in Full View or Slideshow mode to

display the USB On screen menu.

Picture Setting – Adjust Color, Tint, Contrast,

Brightness, Sharpness and Dynamic Contrast.

NOTE: Picture Settings are separate configurations from the

settings in TV and AV inputs.

View pictures on your HDTV with the use of a USB

mass storage device (not included.)

Any of the two USB inputs on your HDTV may be used.

NOTE: When two devices are hooked up, only the first one is

recognized and available as an input.

NOTE: The HDTV switches to USB

Input when a USB flash drive is

detected.

USB FLASH

DRIVE

USB INPUT

USB MAIN MENU SCREEN

THUMBNAIL VIEW SCREEN

NOTE: A thumbnail hide icon will appear if a

picture cannot be decoded or if no

thumbnail data is available.

SLIDE SHOW

SETUP MENU

FULL VIEW

OPTIONS MENU

All manuals and user guides at all-guides.com

Need help? http://ca.sanyo.com 1-800-263-2244

WARRANTY APPLICATION

New, unused SANYO Color Television products purchased in

Canada through a SANYO authorized dealer are warranted

against manufacturing defects in materials and workmanship

for ONE YEAR for parts and labor, from the date of purchase

by the original retail purchaser for non-commercial use. This

warranty only applies in favor of the original retail purchaser of

the warranted product.

SANYO CANADA INC.'S RESPONSIBILITY

During the warranty period, SANYO Canada Inc. will repair, or

at our option, replace a Color Television product which shows

evidence of a manufacturing defect in materials or workman-

ship.

Replacement PARTS are warranted for the remaining portion

of the warranty period.

WHAT IS NOT COVERED

(a) Color Television products purchased outside Canada.

(b) Color Television products purchased in a used condition.

(d) Adjustments that are outlined in the Operating Manual.

(e) Accessory items including antenna, batteries and

connecting cables.

(f) Damage in or due to transportation.

(g) Damage due to improper maintenance, accident, abuse,

misuse or negligence.

(h) Damage caused by lightning and power surges.

ORIGINAL RETAIL PURCHASER'S RESPONSIBILITY

You, the original retail purchaser, must present your original,

dated bill-of-sale together with this warranty to SANYO Canada

Inc. or to an authorized SANYO Service Depot* when you

make a claim under this warranty.

You, the original retail purchaser, are responsible for any costs

of TRANSPORTING the product to and from SANYO Canada

Inc. or an authorized SANYO Service Depot. You also are

responsible for the cost of any MAINTENANCE necessary in

respect of the product.

*In-home service is only available to the units whose screen

size is 46 inches or over, and limited to the locations within a

30-km radius of any authorized SANYO Service Depot,

throughout Canada.

WARRANTY BECOMES VOID This warranty becomes void if

the product's serial numbers are altered or removed or if any

repair to the product is made other than by SANYO Canada Inc.

or by an authorized SANYO Service Depot.

LIMITATIONS

(a) SANYO Canada Inc. reserves the right to change or

improve the design of the model of the product warranted

hereunder without incurring any obligation to make any

modifications to or to install any improvement in or on the

product.

(b) In no event shall SANYO Canada Inc. or any of its

Authorized Dealers be liable for special or consequential

damage arising from the use of this product.

STATUTORY WARRANTIES

The above provisions do not preclude the operation of any

applicable provincial statute which in certain

circumstances may not allow some of the limitations and

exclusions described in this Warranty. Where any terms

of this Warranty are prohibited by such a statute, they shall be

deemed null and void but the remainder of this

warranty shall remain in effect.

HOW TO OBTAIN WARRANTY SERVICE

Please contact the SANYO Authorized Dealer from whom the

product was purchased or contact us directly at:

SANYO Canada Inc.

201 Creditview Road

Woodbridge Ont. L4L 9T1

(905) 265-4100

1-800-263-2244

SANYO COMFORT WARRANTY

All manuals and user guides at all-guides.com

La page charge ...

Sanyo LCD55L4 Manuel utilisateur

Marque: Sanyo

Modèle: LCD55L4

Catégorie: Équipement musical supplémentaire

Taper: Manuel utilisateur

Télécharger le PDF

rapport

dans d''autres langues

English: Sanyo LCD55L4 User manual

Sanyo LCD55L4 Manuel utilisateur

Sanyo LCD55L4 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents