Skil AG290202 Le manuel du propriétaire

Marque: Skil

Modèle: AG290202

Catégorie: Outils électroportatifs

Taper: Le manuel du propriétaire

Ce manuel convient également à

AG290201

WARNING: To reduce the risk of injury, the user must read and understand the

Owner’s Manual before using this product. Save these instructions for future reference.

AVERTISSEMENT : Afin de réduire les risques de blessure, l’utilisateur doit lire et

comprendre le guide d’utilisation avant d’utiliser cet article. Conservez le présent guide

afin de pouvoir le consulter ultérieurement.

ADVERTENCIA : Para reducir el riesgo de lesiones, el usuario debe leer y comprender

el Manual del operador antes de utilizar este producto. Guarde estas instrucciones para

consultarlas en caso sea necesario.

Owner’s Manual

Guide d’utilisation

Manual del propietario

For Customer Service

Pour le service à la clientèle

Servicio al cliente

20V 4-1/2'' Angle Grinder

Meuleuse angulaire de 20 V (11,5 cm)

1-877-SKIL-999

www.skil.com

Model/ Modelo/ Modèle: AG290201

TABLE OF CONTENTS

General Power Tool Safety Warnings . ............................3-4

Safety Warnings for Angle Grinder ...............................5-6

Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-10

Get to Know Your Angle Grinder ..................................11

Accessories ...................................................12

Specications .................................................12

Operating Instructions .......................................13-18

Maintenance ...................................................19

Troubleshooting ...............................................19

Limited Warranty of SKIL Cordless Tool ............................20

WARNING

•

Some dust created by power sanding, sawing, grinding, drilling and other

construction activities contains chemicals known to the State of California to cause cancer,

birth defects or other reproductive harm. Some examples of these chemicals are:

–

Lead from lead-based paints.

–

Crystalline silica from bricks, cement, and other masonry products.

–

Arsenic and chromium from chemically-treated lumber.

•

Your risk from these exposures varies, depending upon how often you do this type of work.

To reduce your exposure to these chemicals:

–

Work in a well-ventilated area.

–

Work with approved safety equipment, such as dust masks that are specially designed to

lter out microscopic particles.

–

Avoid prolonged contact with dust from power sanding, sawing, grinding, drilling, and

other construction activities. Wear protective clothing and wash exposed areas with soap

and water. Allowing dust to get into your mouth or eyes or to lie on the skin may promote

absorption of harmful chemicals.

GENERAL POWER TOOL SAFETY WARNINGS

WARNING

Read all safety warnings and all instructions. Failure to follow the

warnings and instructions may result in electric shock, re and/or serious

injury.

SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE

REFERENCE.

The term "power tool" in the warnings refers to your mains-operated (corded) power tool or

battery-operated (cordless) power tool.

Work area safety

Keep work area clean and well lit. Cluttered or dark areas invite accidents.

Do not operate power tools in explosive atmospheres, such as in the presence of

ammable liquids, gases or dust. Power tools create sparks which may ignite the dust or

fumes.

Keep children and bystanders away while operating a power tool. Distractions can cause

you to lose control.

Electrical safety

Power tool plugs must match the outlet. Never modify the plug in any way. Do not use

any adapter plugs with earthed (grounded) power tools. Unmodied plugs and matching

outlets will reduce risk of electric shock.

Avoid body contact with earthed or grounded surfaces, such as pipes, radiators,

ranges and refrigerators. There is an increased risk of electric shock if your body is earthed

or grounded.

Do not expose power tools to rain or wet conditions. Water entering a power tool will

increase the risk of electric shock.

Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power

tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled

cords increase the risk of electric shock.

When operating a power tool outdoors, use an extension cord suitable for outdoor use.

Use of a cord suitable for outdoor use reduces the risk of electric shock.

If operating a power tool in a damp location is unavoidable, use a ground fault circuit

interrupter (GFCI) protected supply. Use of an GFCI reduces the risk of electric shock.

Personal safety

Stay alert, watch what you are doing and use common sense when operating a power

tool. Do not use a power tool while you are tired or under the inuence of drugs,

alcohol or medication. A moment of inattention while operating power tools may result in

serious personal injury.

Use personal protective equipment. Always wear eye protection. Protective equipment

such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate

conditions will reduce personal injuries.

Prevent unintentional starting. Ensure the switch is in the off-position before

connecting to power source and/or battery pack, picking up or carrying the tool.

Carrying power tools with your nger on the switch or energising power tools that have the

switch on invites accidents.

Remove any adjusting key or wrench before turning the power tool on. A wrench or a

key left attached to a rotating part of the power tool may result in personal injury.

Do not overreach. Keep proper footing and balance at all times. This enables better

control of the power tool in unexpected situations.

Dress properly. Do not wear loose clothing or jewellery. Keep your hair and clothing

away from moving parts. Loose clothes, jewellery or long hair can be caught in moving

parts.

If devices are provided for the connection of dust extraction and collection facilities,

ensure these are connected and properly used. Use of dust collection can reduce

dust-related hazards.

Power tool use and care

Do not force the power tool. Use the correct power tool for your application. The correct

power tool will do the job better and safer at the rate for which it was designed.

Do not use the power tool if the switch does not turn it on and off. Any power tool that

cannot be controlled with the switch is dangerous and must be repaired.

Disconnect the plug from the power source and/or the battery pack from the power tool

before making any adjustments, changing accessories, or storing power tools. Such

preventive safety measures reduce the risk of starting the power tool accidentally.

Store idle power tools out of the reach of children and do not allow persons unfamiliar

with the power tool or these instructions to operate the power tool. Power tools are

dangerous in the hands of untrained users.

Maintain power tools. Check for misalignment or binding of moving parts, breakage of

parts and any other condition that may affect the power tool’s operation. If damaged,

have the power tool repaired before use. Many accidents are caused by poorly maintained

power tools.

Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting

edges are less likely to bind and are easier to control.

Use the power tool, accessories and tool bits etc. in accordance with these instructions,

taking into account the working conditions and the work to be performed. Use of the

power tool for operations different from those intended could result in a hazardous situation.

Battery tool use and care

Recharge only with the charger specied by the manufacturer. A charger that is suitable

for one type of battery pack may create a risk of re when used with another battery pack.

Use power tools only with specically designated battery packs. Use of any other battery

packs may create a risk of injury and re.

When battery pack is not in use, keep it away from other metal objects, like paper clips,

coins, keys, nails, screws or other small metal objects, that can make a connection

from one terminal to another. Shorting the battery terminals together may cause burns or a

re.

Under abusive conditions, liquid may be ejected from the battery; avoid contact. If

contact accidentally occurs, ush with water. If liquid contacts eyes, additionally seek

medical help. Liquid ejected from the battery may cause irritation or burns.

Service

Have your power tool serviced by a qualied repair person using only identical

replacement parts. This will ensure that the safety of the power tool is maintained.

SAFETY WARNINGS FOR ANGLE GRINDER

Safety Warnings Common for Grinding:

This power tool is intended to function as a grinder. Read all safety warnings,

instructions, illustrations and specications provided with this power tool. Failure to

follow all instructions listed below may result in electric shock, re and/or serious injury.

Operations such as sanding, wire brushing, polishing or cutting-off are not

recommended to be performed with this power tool. Operations for which the power tool

was not designed may create a hazard and cause personal injury.

Do not use accessories which are not specically designed and recommended by the

tool manufacturer. Just because the accessory can be attached to your power tool, it does

not assure safe operation.

The rated speed of the accessory must be at least equal to the maximum speed marked

on the power tool. Accessories running faster than their rated speed can break and y apart.

The outside diameter and the thickness of your accessory must be within the capacity

rating of your power tool. Incorrectly sized accessories cannot be adequately guarded or

controlled.

Threaded mounting of accessories must match the grinder spindle thread. For

accessories mounted by ange, the arbor hole of the accessory must t the locating

diameter of the ange. Accessories that do not match the mounting hardware of the power

tool will run out of balance, vibrate excessively and may cause loss of control.

Do not use a damaged accessory. Before each use inspect the accessory such as

abrasive wheels for chips and cracks, backing pad for cracks, tear or excess wear,

wire brush for loose or cracked wires. If power tool or accessory is dropped, inspect

for damage or install an undamaged accessory. After inspecting and installing an

accessory, position yourself and bystanders away from the plane of the rotating

accessory and run the power tool at maximum no-load speed for one minute.

Damaged accessories will normally break apart during this test time.

Wear personal protective equipment. Depending on application, use face shield, safety

goggles or safety glasses. As appropriate, wear dust mask, hearing protectors, gloves

and workshop apron capable of stopping small abrasive or workpiece fragments. The

eye protection must be capable of stopping ying debris generated by various operations. The

dust mask or respirator must be capable of ltrating particles generated by your operation.

Prolonged exposure to high intensity noise may cause hearing loss.

Keep bystanders a safe distance away from work area. Anyone entering the work

area must wear personal protective equipment. Fragments of workpiece or of a broken

accessory may y away and cause injury beyond immediate area of operation.

Hold the power tool by insulated gripping surfaces only, when performing an operation

where the cutting tool may contact hidden wiring. Contact with a "live" wire will also make

exposed metal parts of the power tool "live" and could give the operator an electric shock.

Never lay the power tool down until the accessory has come to a complete stop. The

spinning accessory may grab the surface and pull the power tool out of your control.

Do not run the power tool while carrying it at your side. Accidental contact with the

spinning accessory could snag your clothing, pulling the accessory into your body.

Regularly clean the power tool’s air vents.

The motor’s

fan will draw the dust inside the

housing and excessive accumulation of powdered metal may cause electrical hazards.

Do not operate the power tool near ammable materials. Sparks could ignite these

materials.

Do not use accessories that require liquid coolants. Using water or other liquid coolants

may result in electrocution or shock.

Further safety instructions for all operations

Kickback and Related Warnings:

Kickback is a sudden reaction to a pinched or snagged rotating wheel, backing pad, brush

or any other accessory. Pinching or snagging causes rapid stalling of the rotating accessory

which in turn causes the uncontrolled power tool to be forced in the direction opposite of the

accessory’s rotation at the point of the binding.

For example, if an abrasive wheel is snagged or pinched by the workpiece, the edge of the

wheel that is entering into the pinch point can dig into the surface of the material causing the

wheel to climb out or kick out. The wheel may either jump toward or away from the operator,

depending on direction of the wheel’s movement at the point of pinching. Abrasive wheels

may also break under these conditions.

Kickback is the result of power tool misuse and/or incorrect operating procedures or conditions

and can be avoided by taking proper precautions as given below.

Maintain a rm grip on the power tool and position your body and arm to allow you to

resist kickback forces. Always use auxiliary handle, if provided, for maximum control

over kickback or torque reaction during start-up. The operator can control torque reactions

or kickback forces, if proper precautions are taken.

Never place your hand near the rotating accessory. Accessory may kickback over your

hand.

Do not position your body in the area where power tool will move if kickback occurs.

Kickback will propel the tool in direction opposite to the wheel’s movement at the point of

snagging.

Use special care when working corners, sharp edges etc. Avoid bouncing and snagging

the accessory. Corners, sharp edges or bouncing have a tendency to snag the rotating

accessory and cause loss of control or kickback.

Do not attach a saw chain woodcarving blade or toothed saw blade. Such blades create

frequent kickback and loss of control.

Safety Warnings Specic for Grinding:

Use only wheel types that are recommended for your power tool and the specic guard

designed for the selected wheel. Wheels for which the power tool was not designed cannot

be adequately guarded and are unsafe.

The grinding surface of centre depressed wheels must be mounted below the plane of

the guard lip. An improperly mounted wheel that projects through the plane of the guard lip

cannot be adequately protected.

The guard must be securely attached to the power tool and positioned for maximum

safety, so the least amount of wheel is exposed towards the operator. The guard helps to

protect the operator from broken wheel fragments, accidental contact with wheel and sparks

that could ignite clothing.

Wheels must be used only for recommended applications. For example: do not grind

with the side of cut-off wheel. Abrasive cut-off wheels are intended for peripheral grinding,

side forces applied to these wheels may cause them to shatter.

Always use undamaged wheel anges that are of correct size and shape for your

selected wheel. Proper wheel anges support the wheel thus reducing the possibility of wheel

breakage. Flanges for cut-off wheels may be different from grinding wheel anges.

Do not use worn down wheels from larger power tools. Wheel intended for larger power

tool is not suitable for the higher speed of a smaller tool and may burst.

SYMBOLS

Safety Symbols

The purpose of safety symbols is to attract your attention to possible dangers. The safety sym-

bols and the explanations with them deserve your careful attention and understanding. The

symbol warnings do not, by themselves, eliminate any danger. The instructions andwarnings

they give are no substitutes for proper a cident prevention measures.

WARNING

Be sure to read and understand all safety instructions in this Owner’s

Manual, including all safety alert symbols such as “DANGER,” “WARN-

ING,” and “CAUTION” before using this tool. Failure to following all instructions listed below

may result in electric shock, re, and/or serious personal injury.

The denitions below describe the level of severity for each signal word. Please read the manual

and pay attention to these symbols

This is the safety alert symbol. It is used to alert you to potential

personal injury hazards. Obey all safety messages that follow this

symbol to avoid possible injury or death.

DANGER

DANGER indicates a hazardous situation which, if not avoided, will

result in death or serious injury.

WARNING

WARNING indicates a hazardous situation which, if not avoided, could

result in death or serious injury.

CAUTION

CAUTION, used with the safety alert symbol, indicates a hazardous

situation which, if not avoided, will result in minor or moderate injury.

Damage Prevention and Information Messages

These inform the user of important information and/or instructions that could lead to equip-

ment or other property damage if they are not followed. Each message is preceded by the

word “NOTICE”, as in the example below:

NOTICE: Equipment and/or property damage may result if these instructions are not followed.

WARNING

The operation of any power tools can result in foreign

objects being thrown into your eyes, which can result

in severe eye damage. Before beginning power tool operation, always

wear safety goggles or safety glasses with side shields and a full face

shield when needed. We recommend a Wide Vision Safety Mask for use

over eyeglasses or standard safety glasses with side shields. Always

use eye protection which is marked to comply with ANSI Z87.1..

SYMBOLS (CONTINUED)

IMPORTANT: Some of the following symbols may be used on your tool. Please study them

and learn their meaning. Proper interpretation of these symbols will allow you to operate the

tool better and more safely.

Symbol Name Designation/Explanation

V Volts Voltage (potential)

A Amperes Current

Hz Hertz Frequency (cycles per second)

W Watt Power

kg Kilograms Weight

min Minutes Time

s Seconds Time

Wh Watt-hours Battery capacity

Ah Ampere-Hours Battery capacity

Ø Diameter Size of drill bits, grinding wheels, etc.

No load speed Rotational speed, at no load

n Rated speed Maximum attainable speed

…/min

Revolutions or reciprocation

per minute

Revolutions, strokes, surface speed,

orbits, etc. per minute

0 Off position Zero speed, zero torque...

1,2,3,…

I,II,III,

Selector settings

Speed, torque, or position settings.

Higher number means greater speed

Innitely variable selector

with off

Speed is increasing from 0 setting

Arrow Action in the direction of arrow

Alternating current Type or a characteristic of current

Direct current Type or a characteristic of current

Alternating or direct current Type or a characteristic of current

Class II construction

Designates Double Insulated Construction

tools.

Earthing terminal Grounding terminal

Li-ion RBRC seal

Designates Li-ion battery recycling

program

Ni-Cad RBRC seal

Designates Ni-Cad battery recycling

program

Symbol Name Designation/Explanation

Read manual symbol Alerts user to read manual

Wear eye protection symbol Alerts user to wear eye protection

SYMBOLS (CERTIFICATION INFORMATION)

IMPORTANT: Some of the following symbols for certication information may be used on your

tool. Please study them and learn their meaning. Proper interpretation of these symbols will

allow you to operate the tool better and more safely.

Symbol Designation/Explanation

This symbol designates that this tool is listed by Underwriters Laboratories.

This symbol designates that this tool is recognized by Underwriters

Laboratories.

This symbol designates that this tool is listed by Underwriters

Laboratories, to United States and Canadian Standards.

This symbol designates that this tool is listed by the Canadian

Standards Association.

This symbol designates that this tool is listed by the Canadian

Standards Association, to United States and Canadian Standards.

This symbol designates that this tool is listed by the Intertek Testing

Services, to United States and Canadian Standards.

This symbol designates that this tool complies to NOM Mexican

Standards.

GET TO KNOW YOUR ANGLE GRINDER

20V Brushed Angle Grinder

Switch Button

Spindle Lock

Ventilation Openings

Auxiliary Handle

Wrench

Wrench Storage

Compartment

Wheel Guard

Guard

Release/Lock

Latch

Backing Flange

Grinding Wheel

Lock Nut

Spindle

Fig. 1

Accessories

Part Name Note

4-1/2” (Ø115 mm) Grinding Wheel

Provided as a pair.

4-1/2” (Ø115 mm) Wheel Guard

Auxiliary Handle (Wrench on storage type)

Provided as a pair.

Wrench

Backing Flange and Lock Nut Provided as a pair.

Specications

Rated voltage 20V d.c.

Rated Speed 8500 /min

Wheel Diameter Ø4-1/2’’(115mm)

Wheel Thickness 6mm

Wheel Type Type 27 (only)

Spindle Thread M14

Recommended working temperature 14 ~ 104°F (-10 ~ 40°C)

Recommended storage temperature 32 ~ 104°F (0 ~ 40°C)

WARNING

Use only Type 27 grinding wheels. Using accessories not designed for

this tool can cause serious injury.

OPERATING INSTRUCTIONS

WARNING

To reduce the risk of re, personal injury, and product damage due to

a short circuit, never immerse your tool, battery ack or charger in

uid or allow a uid to ow inside them. Corrosive or conductive uids, such as seawater,

certain industrial chemicals, and bleach or bleach-contain ng products, etc, can cause a short

circuit.

WARNING

If any parts are damaged or missing, do not operate this product until

the parts are replaced. Use of this product with damaged or missing parts

could result in serious personal injury.

WARNING

Do not attempt to modify this tool or create accessories not

recommended for use with this tool. Any such alteration or modication

is misuse and could result in a hazardous condition leading to possible serious injury.

WARNING

To prevent accidental starting that could cause serious personal

injury, always remove the battery pack from the tool when

assembling parts.

This cordless angle grinder must be used only with the battery packs and charger listed below:

Battery Pack Charger

2Ah 4Ah 5Ah

SKIL SC535801

SKIL BY519701 SKIL BY519601 SKIL BY519603

NOTICE: Please refer to the battery and charger manuals for detailed operating information.

Wheel Guard Installation (Fig. 2, 3)

WARNING

Use wheel guard with disc grinding wheels. Always close the latch to

secure the guard. Keep the guard between you and the wheel. Do not

direct the guard opening toward your body.

Turn the tool OFF and remove the battery pack before performing any assembly.

To install the wheel guard:

a. Open the guard latch and position the wheel guard on the spindle neck so that the two

bumps on the guard line up with the two notches on the spindle neck.

b. Rotate the wheel guard to the desired position, then close the latch to secure the guard in

place.

Fig. 2

c. Check to ensure that the wheel guard is

securely clamped to the spindle neck. If the

guard latch does not securely clamp the

wheel guard to the spindle neck, place the

wheel guard on the spindle neck, close the

latch, then tighten the adjustment screw to

increase the clamping tension (Fig. 3). Check

it again and do not proceed until the wheel

guard is properly clamped in place.

To remove the wheel guard:

a. Open the guard latch; rotate the wheel guard

until the bumps on the guard line up with the

notches on the spindle neck.

b. Lift the wheel guard off the spindle neck.

Grinding Wheel Assembly

Turn the tool OFF and remove the battery pack before performing any assembly. Be sure that

the wheel guard is in place for grinding.

To install the grinding wheel:

a. Place the backing ange on the spindle. Check to ensure that the backing ange is properly

seated on the spindle. It will click into place on the spindle and will cause the spindle to

rotate when the backing ange is rotated.

b. Place the grinding wheel on the backing ange.

c. Thread the lock nut on the spindle with the at side of the ange facing outside. Make sure

that the opening in the grinding wheel is positioned around the raised portion of the lock nut

(Fig. 4).

Fig. 4

Lock Nut

Grinding Wheel

Backing Flange

Spindle

Fig. 3

d. While pressing the spindle lock, tighten

the lock nut by turning it clockwise with the

wrench supplied (Fig. 5).

To remove the grinding wheel:

e. While pressing the spindle lock, loosen the

lock nut by turning it counter-clockwise with

the wrench supplied.

WARNING

Press the spindle lock

only when the spindle is

at a standstill.

WARNING

Use protective gloves

when removing the

grinding wheel from the tool, or rst allow

the grinding wheel to cool down. It may be

hot after prolonged use.

Installing the Auxiliary Handle

(Fig. 6)

The auxiliary handle, used to guide and

balance the tool, can be threaded into the front

housing on either side of the tool, depending on

personal preference and comfort.

Turn the tool OFF and remove the battery pack

before performing any assembly. Thread the

auxiliary handle into the desired position and

securely tighten it in place.

Fig. 5

Fig. 6

To Attach/Detach Battery Pack

(Fig. 7)

Be careful not to turn on the tool when

attaching the battery pack.

To attach the battery pack:

Align the raised rib on the battery pack with the

grooves in the tool, and then slide the battery

pack onto the tool.

To detach the battery pack:

Depress the battery-release button located

on the front of the battery pack to release the

battery pack. Pull the battery pack out and

remove it from the tool.

NOTICE: When placing the battery pack on the

tool, be sure that the raised rib on the battery pack aligns with the groove inside the tool and

that the latches snap into place properly. Improper attachment of the battery pack can cause

damage to internal components.

WARNING

Battery tools are always in operating condition. Be careful when the

tool is not in use or when carrying it at your side.

Fig. 7

Battery-

Release

Button

Attach

Detach

Switch Button

The tool can be turned “ON” with the switch button, located at the side of the motor housing.

The switch button can be locked in the “ON” position, a convenience for long grinding

operations.

To turn the tool “ON” without locking it:

Slide the switch button forward by applying pressure ONLY at the REAR portion of the button.

When pressure is released the switch button will snap to the “OFF” position (Fig. 8a).

To lock the switch “ON”:

Slide the switch button forward and press in on the FRONT portion (Fig. 8b).

To unlock the switch:

Simply press and release the REAR portion of the button. The switch is spring loaded and will

snap back automatically (Fig. 8)

Fig. 8

WARNING

Hold the tool with both hands while starting the tool, since torque

from the motor can cause the tool to twist. Start the tool and let the

tool come to full speed before contacting the workpiece. Lift the tool from the work

before releasing the switch.

NOTICE: DO NOT turn the switch “ON” and “OFF” while the tool is under load; this will greatly

decrease the switch life.

Grinding Operations

Selecting Grinding Wheels

WARNING

Before using a grinding wheel, be certain that its maximum safe

operating speed is not exceeded by the nameplate speed of the

grinder. Do not exceed the recommended wheel diameter.

Disc Grinding Wheels

Grinding wheels should be carefully selected in order to use the grinder most efciently.

Wheels vary in type of abrasive, bond, hardness, grit size and structure. The correct type of

wheel to use is determined by the job. Use disc grinding wheels for fast grinding of structural

steel, heavy weld beads, steel casting, stainless steel, and other ferrous metals.

Grinding Tips

Efcient grinding is achieved by controlling the

pressure and keeping the angle between wheel

and the workpiece at 10° to 15° (Fig. 9).

If the wheel is at, the tool is difcult to control.

If the angle is too steep, the pressure is

concentrated on a small area causing burning

to the work surface.

WARNING

Use clamps or other

practical way to secure

and support the workpiece to a stable

platform. Holding the work by hand or against

your body is unstable and may lead to loss of

control and injury.

WARNING

Excessive or sudden

pressure on the wheel will

slow the grinding action and put dangerous stresses on the wheel.

NOTICE: When grinding with a new wheel, be certain to always grind while pulling tool

backwards until wheel becomes rounded on its edge. New wheels have sharp corners that

tend to “bite” or cut into work piece when pushing them forward.

Fig. 9

MAINTENANCE

WARNING

To avoid serious personal injury, always remove the battery pack

from the tool when cleaning or performing any maintenance.

Service

WARNING

Preventive maintenance performed by unauthorized personnel may

result in misplacing of internal wires and components which could

cause serious hazard. We recommend that all tool service be performed by a SKIL Factory

Service Center or Authorized SKIL Service Station.

General Maintenance

WARNING

When servicing, use only identical replacement parts. Use of any

other parts could create a hazard or cause product damage.

Periodically inspect the entire product for damaged, missing, or loose parts such as screws,

nuts, bolts, caps, etc. Tighten securely all fasteners and caps and do not operate this product

until all missing or damaged parts are replaced. Please contact customer service or an autho-

rized service center for assistance.

Cleaning

WARNING

The tool may be cleaned most effectively with compressed dry air. Always

wear safety goggles when cleaning tools with compressed air.

Ventilation openings and switch levers must be kept clean and free of foreign matter. Do not

attempt to clean by inserting pointed objects through openings.

WARNING

Certain cleaning agents and solvents damage plastic parts. Some of

these are: gasoline, carbon tetrachloride, chlorinated cleaning solvents,

ammonia and house hold detergents that contain ammonia.

Storage

Store the tool indoors in a place that is inaccessible to children. Keep away from corrosive

agents.

TROUBLE SHOOTING

Problem Cause Remedy

Tool will not start. 1. Battery pack is depleted.

2. Battery pack is over-

temperature.

3. Battery pack is not installed

properly.

4. Burned out switch.

1. Charge the battery.

2. Turn off the tool and cool the

battery pack under air ow.

3. Conrm battery is locked and

secured to the tool.

4. Have the switch replaced by

an Authorized SKIL Service

Center or Service Station.

LIMITED WARRANTY OF SKIL CONSUMER TOOLS

5 YEAR LIMITED WARRANTY- LEGAL

Chervon North America, Inc. ("Seller") warrants to the original purchaser only, that all SKIL

consumer TOOLS will be free from defects in material or workmanship for a period of ve

years from date of purchase, if original purchaser registers the product within 30 days from

purchase. BATTERIES AND CHARGERS are warranted for 2 years. Product registration

can be completed online at www.Registermyskil.com. Original purchasers should also retain

their receipt as proof of purchase. THE FIVE-YEAR WARRANTY PERIOD FOR TOOLS IS

CONDITIONED ON REGISTRATION OF THE PRODUCT WITHIN 30 DAYS OF PURCHASE.

If original purchasers do not register their product timely, the foregoing limited warranty will

apply for a duration of three years for tools. All batteries and chargers will remain under the

two-year limited warranty.

Notwithstanding the foregoing, if a SKIL consumer tool is used for industrial, professional

or commercial purposes, the foregoing warranty will apply for a duration of ninety days,

regardless of registration.

SELLER’S SOLE OBLIGATION AND YOUR EXCLUSIVE REMEDY under this Limited

Warranty and, to the extent permitted by law, any warranty or condition implied by law, shall

be the repair or replacement of parts, without charge, which are defective in material or

workmanship and which have not been misused, carelessly handled, or repaired by persons

other than Seller or Authorized Service Station. To make a claim under this Limited Warranty,

you must return the complete product, transportation prepaid, to any SKIL Factory Service

Center or Authorized Service Station. For Authorized SKIL Power Tool Service Stations,

please visit www.Registermyskil.com or call 1-877-SKIL-999 (1-877-754-5999).

THIS LIMITED WARRANTY DOES NOT APPLY TO ACCESSORY ITEMS SUCH AS

CIRCULAR SAW BLADES, DRILL BITS, ROUTER BITS, JIGSAW BLADES, SANDING

BELTS, GRINDING WHEELS AND OTHER RELATED ITEMS.

ANY IMPLIED WARRANTIES APPLICABLE TO A PRODUCT SHALL BE LIMITED IN

DURATION EQUAL TO THE DURATION OF THE EXPRESS WARRANTIES APPLICABLE

TO SUCH PRODUCT, AS SET FORTH IN THE FIRST PARAGRAPH ABOVE. SOME

STATES IN THE U.S., SOME CANADIAN PROVINCES DO NOT ALLOW LIMITATIONS ON

HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATION MAY NOT

APPLY TO YOU.

IN NO EVENT SHALL SELLER BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL

DAMAGES (INCLUDING BUT NOT LIMITED TO LIABILITY FOR LOSS OF PROFITS)

ARISING FROM THE SALE OR USE OF THIS PRODUCT. SOME STATES IN THE U.S.

AND SOME CANADIAN PROVINCES DO NOT ALLOW THE EXCLUSION OR LIMITATION

OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR

EXCLUSION MAY NOT APPLY TO YOU.

THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO

HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE IN THE U.S., PROVINCE

TO PROVINCE IN CANADA AND FROM COUNTRY TO COUNTRY.

THIS LIMITED WARRANTY APPLIES ONLY TO PRODUCTS SOLD WITHIN THE UNITED

STATES OF AMERICA, CANADA AND THE COMMONWEALTH OF PUERTO RICO. FOR

WARRANTY COVERAGE WITHIN OTHER COUNTRIES, CONTACT YOUR LOCAL SKIL

DEALER OR IMPORTER.

08/18

La page charge ...

Skil AG290202 Le manuel du propriétaire

Marque: Skil

Modèle: AG290202

Catégorie: Outils électroportatifs

Taper: Le manuel du propriétaire

Ce manuel convient également à

AG290201

Télécharger le PDF

rapport

dans d''autres langues

English: Skil AG290202 Owner's manual

Skil AG290202 Le manuel du propriétaire

Ce manuel convient également à

Skil AG290202 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents