1
Package Contents
9.7” LM-4010 or 9.7” TM-4010
or 10.1” LM-4011 or 10.1” TM-4011
POS Monitor ……………………… (x 1)
Mounting Kits ………………....…...(x 1)
User Manual………………………...(x 1)
Views of TM-4010/LM-4010/TM-4011/LM-4011
Front View of TM/LM-4010
Front View of TM/LM-4011
Rear View
TM-4010/LM-4010
TM-4011/LM-4011
POS Monitor User Manual
10.1” LM-4011 LCD Panel
10.1” TM-4011 P-CAP Touch Panel
Front Cover for
Mounting Bracket
Camera (Optional)
Camera (Optional)
9.7” LM-4010 LCD Panel
9.7” TM-4010 P-CAP Touch Panel
19640901030 Ver. C0
http://www.posiflex.com
2
SOME IMPORTANT NOTES
FCC NOTES
This system meets industry & government requirements and applicable standards. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions manual, may cause interference to radio
communications. It has been tested and found to comply with limits for a Class A
digital device pursuant to subpart B of Part 15 of FCC Rules, which are designed to
provide reasonable protection against interference when operated in a commercial
environment. Operation of this equipment in a residential area is likely to cause
interference in which case the user at his own expense will be required to take whatever
measures to correct the interference.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may cause
undesired operation.
CE CLASS A WARNING
This equipment is compliant with Class A of CISPR 32. In a residential environment
this equipment may cause radio interference.
AVERTISSEMENT CE CLASSE A
Cet équipement est conforme à la classe A de CISPR 32. Dans un environnement
résidentiel, cet équipement peut provoquer des interférences radio.
WARRANTY LIMITS
Warranty will terminate automatically when the machine is opened by any person other
than the authorized technicians. The user should consult his/her dealer for the problem
happening. Warranty voids if the user does not follow the instructions in application of
this merchandise. The manufacturer is by no means responsible for any damage or
hazard caused by improper application.
LIMITES DE GARANTIE
La garantie prend fin automatiquement lorsque la machine est ouverte par une personne
autre que les techniciens autorisés. L'utilisateur doit consulter son revendeur pour le
problème qui se produit. La garantie s'annule si l'utilisateur ne suit pas les instructions
d'application de cette marchandise. Le fabricant n'est en aucun cas responsable de tout
dommage ou danger causé par une mauvaise application.
警告使用者
此為甲類資訊技術設備產品，於居住環境中使用時，可能會造成射頻擾動，在此
種情況下，使用者會被要求採取某些適當的對策。
3
Mounting your Monitor to RT-series POS Terminals
The following instructions are provided to help you mount your TM/LM-4010
or TM/LM-4011 to Posiflex RT-series POS terminals. During installation,
please ensure the terminal is properly turned off and disconnected from the
power sources to avoid potential hazards.
1. Tile the screen of your RT-series terminal to
the most upright position.
2. Remove the system cover by holding down
the release levers at the bottom of the cover
and then pulling the cover outwards.
3. Take the monitor out of package box, and remove the front cover for
mounting bracket.
4. Tear off the release liner from the protective
strip which is clipped onto the mounting
bracket.
4
5. Lift the monitor, align the two screws holes located on the mounting
bracket with those on the top of the system compartment of RT-series
terminals and then secure the monitor with two fixing screws.
6. After ensuring the monitor is well mounted to RT-series terminal, push
back the front cover for the mounting bracket of TM/LM-4010 or
TM/LM-4011.
7. Tile the monitor screen all the way up.
8. Well insert the cable to the internal VGA port from the mainboard of
RT-series terminal, and tuck the extra cable inside the system
compartment.
5
9. Place back the sytem cover to close the system
compartment of RT-Series terminal.
10. Tile the monitor screen to your desired angle.
While setting up the tilting adjustment, be
careful NOT to press on the LCD panel.
Identifying your Monitor as Secondary Touchscreen Monitor
in Extended Mode
In the following section the related descriptions will be offered to help you set
up TM series as the extended monitor when you attempt to extend the desktop
across multiple monitors
For TM-4010/4011 Models with P-CAP Touchscreen
If your monitors are TM-4010/TM-4011 models, you may configure the
display settings from Control Panel in Microsoft Windows to identify the
monitor as the secondary touchscreen monitor. Please go through the below
steps to complete configuration.
1. Make sure that the monitor is well connected to your POS terminal.
2. Go to Control Panel>Display Settings, change your display settings to
extended mode.
3. Go to Control Panel, and then click on
Tablet PC Settings item.
4. In Tablet PC Settings dialogue box, click
on Setup button.
6
5. Following the instruction shown on the screen, click on the screen that
you want to identify as the primary touchscreen display.
6. Press Enter button to proceed the configuration.
7. Click on the screen you want to use as the secondary touchscreen
display.
Powering ON/OFF your Monitor
To start up TM-4010/LM-4010/TM-4011/LM-4011, please make sure that the
monitor is well connected to POS terminals and electricity is supplied to the
monitor through POS terminal.
Installing Drivers
Please visit Posiflex official website to download and install the related drivers.
http://www.posiflex.com/en-global/Download/download)
Setting up Display Resolution for Your Monitor
The below chart defines the list of recommended display settings for
TM/LM-4010 or TM/LM-4011. Improper display configuration will prevent
the monitor from properly displaying the image and lead to a warning message
of “out of range” prompted on the screen.
7
9.7” TM/LM-4010
Display Resolution
Horizontal Frequency (KHz)
Refresh Rate (Hz)
640 x 400
37.9
70
640 x 480
31.5
60
37.9
72
37.5
75
720 x 400
37.9
70
800 x 600
35.1
56
37.9
60
48.1
72
46.9
75
1024 x 768
48.4
60
10.1” TM/LM-4011
Display Resolution
Horizontal Frequency (KHz)
Refresh Rate (Hz)
640 x 480
31.5
60
37.9
72
37.5
75
800 x 600
37.9
60
48.1
72
46.9
75
1024 x 768
48.4
60
1280 x 720
45.0
60
1280 x 800
49.7
60
Specification
TM-4011
LM-4011
TM-4010
LM-4010
Display
LCD Panel
10.1" TFT LCD
9.7" TFT LCD
Resolution
1280(H) x 800 (V)
1024(H) x 768 (V)
Active Area
216.96mm (H) x
135.60mm (V)
196.61mm (H) x
147.46mm (V)
Pixel
Arrangement
R.G.B. Vertical Stripe
Viewing
Angle
85/85/85/85 degree
(U/D/L/R)
70/60/70/70 degree
(U/D/L/R)
Contrast Ratio
800 : 1
500 : 1
Response time
25ms
20ms
Brightness
400 cd/m
2
350 cd/m
2
8
Display
Interface
VGA
Power Supply
12V from Posiflex terminal VGA Port
Touch
Touch type
P-CAP
N/A
P-CAP
N/A
Interface
USB
N/A
USB
N/A
※
The product information and specifications are subject to change without
prior notice. To get the detailed information on TM-4010/LM-4010/TM-
4011/LM-4011 please check this model from Posiflex Global Website
(http://www.posiflex.com/en-global/Download/download).
BSMI ROHS
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
Posiflex LM-4010 Manuel utilisateur
- Taper
- Manuel utilisateur
dans d''autres langues
- English: Posiflex LM-4010 User manual
Documents connexes
-
Posiflex TM/LM-5011P Manuel utilisateur
-
Posiflex RT-5115 Manuel utilisateur
-
-
Posiflex RT-6115 Manuel utilisateur
-
Posiflex RT-5015E Manuel utilisateur
-
-
-
-