Appareo AT-130 Guide d'installation

Taper
Guide d'installation
AT-130
INSTALLATION MANUAL
Document revision: 1.1
Last revised: March 17, 2021
AT-130 Installation Manual
600840-000064, rev 1.1 Page 2 of 6
AT-130
Installation Manual
© 2020-21 Appareo Systems, LLC. All Rights Reserved.
AT-130 Installation Manual. All content within is copyrighted by Appareo Systems, LLC, and
may not be reprinted without permission.
The content of this manual is furnished for informational use only, is subject to change without
notice, and should not be construed as a commitment by Appareo Systems. Appareo Systems
assumes no responsibility or liability for any errors or inaccuracies that may appear in the
content contained in this guide.
AT-130, Appareo, Appareo Systems, and the Appareo logo are trademarks or registered
trademarks of Appareo Systems. All other trademarks are property of their respective owner.
Appareo Systems, 1810 NDSU Research Circle North, Fargo, ND 58102 USA.
Visit us online at www.appareo.com
Questions? E-mail us at [email protected]
Record of Revision
Revision
Number Change Description Revision
Date
Inserted
By
1.0 Initial release 2/26/21 AAL
1.1 Clarified orientation instructions and bolt size. 3/17/21 AAL
AT-130 Installation Manual
600840-000064, rev 1.1 Page 3 of 6
1. Compliance
This device complies with part 15 of the FCC Rules and applicable RSS standards.
Operation is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Le présent materiel est conforme aux CNRexempts de licence d'Industrie Canada. Son
fonctionnement est soumis aux deux conditions suivantes: (1) cet appareil ne peut pas
provoquer d'interférences, et (2) cet appareil doit accepter toute interférence, y compris
celles susceptibles de provoquer le fonctionnement du dispositive.
Cet appareil contient des émetteurs / récepteurs exempts de licence qui sont conformes
aux RSS exemptes de licence d'Innovation, Sciences et Développement économique
Canada. Son fonctionnement est soumis aux deux conditions suivantes: Cet appareil ne
doit pas provoquer d'interférences. Cet appareil doit accepter toute interférence, y
compris les interférences qui peuvent provoquer un fonctionnement indésirable de
l'appareil.
Note: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
In order to comply with FCC and ISED RF Exposure requirements, this device must be
installed such that a minimum separation distance of 20 cm is maintained between it and
all persons during normal operation.
Afin de se conformer aux exigences d'exposition aux RF de la d'ISDE, cet appareil doit
être installé de telle sorte qu'une distance de séparation minimale de 20 cm soit
maintenue. entre lui et toutes les personnes pendant le fonctionnement normal.
FCC ID: 2AETC-AT130
AT-130 Installation Manual
600840-000064, rev 1.1 Page 4 of 6
2. About AT-130
The Appareo Asset Tracker, model AT-130 is a cost-effective, cellular, IP69K-rated asset
tracking device with ultra-long battery life and industrial operating temperature range (-40 to
+85 ).
3. Activating AT-130
In order to use AT-130, you need to activate it.
1. Peel off the clear label covering the magnet on the back of the unit as shown below. Flip
over the unit to remove the magnet.
2. Put the magnet in the Device Activation slot for five seconds. Check your asset tracking
software to confirm that the device is activated (it should appear within 5-10 minutes if
the unit is outside with the logo facing up).
Once the device is activated, discard the magnet.
AT-130 Installation Manual
600840-000064, rev 1.1 Page 5 of 6
4. Installing AT-130
Installation Location
Choose an installation location that meets the following specifications:
Mounted on a clean, flat surface.
Mounted as high up as possible.
Mounted in one of the following orientations:
o Best: Mount the unit so that the top of the unit (the side that does not have the
Device Activation text on it) has a clear view of the sky (not underneath or blocked by
a metal surface).
o Good: Orient the unit so that the Device Activation text on the back of the unit is
upright. Mount the unit so that the top side of the unit has a clear view of the sky (not
underneath or blocked by a metal surface).
The device shall be installed on the equipment so that the operator is, at minimum,
20 cm away from all external surfaces of the device.
AT-130 Installation Manual
600840-000064, rev 1.1 Page 6 of 6
Installing AT-130
Use 1/4" or M6 bolts, washers, and nuts to mount AT-130 to its mounting location. Torque to a
maximum of 15 ft-lbs.
The spacing between bolts is 114 mm, as shown below.
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6

Appareo AT-130 Guide d'installation

Taper
Guide d'installation

dans d''autres langues