TrolMaster TWS-1 Manuel utilisateur

Marque
TrolMaster
Modèle
TWS-1
Taper
Manuel utilisateur
TWS-1
TrolMaster Wireless Station
Read all instructions carefully before installation.
This product is not intended for use by any persons
and children with reduced physical, sensory or mental
capabilities or lack of experience and product
knowledge.
The device is designed to be installed INDOORS IN A
SPACE THAT IS PROTECTED FROM RAIN AND
FLOODING.
DO NOT clean the exterior of the enclosure with any
chemicals that might cause damage. To clean the
enclosure… Use a damp cloth only.
CAUTION
The TWS-1 Wireless Station enables you to use
TrolMaster sensors and devices wirelessly with your
existing Hydro-X Pro Controller (HCS-2). The TWS-1 is
the core of the wireless system, designed to convert
wired and wireless protocols, thus building a scalable,
solid communication link between the HCS-2 controller,
sensors, and devices. The TWS-1 provides a wiring-free
option for TrolMaster’s future wireless product
development, to enhance user experiences by offering
the option to connect sensors and devices wirelessly.
OVERVIEW
1.
2.
3.
4.
02
1 x TrolMaster Wireless Station (TWS-1)
1 x Antenna
2 x Phillips Head Screws (0.05in / 1.28mm)
SPECIFICATION
12V, 80mA
Temperature: 32°-122°F
Humidity: ≤90%
Working Environment:
Unit: 60mm x 82.5mm x 25mm
Screw Size: Phillips Head (0.05" / 1.28mm)
RJ12 cable: 16ft (4.9m)
Antenna: 6.99" (177.5mm)
Product Dimensions:
Input Voltage:
915Mhz Lora
Wireless Standard:
0.42 lbs
Product Weight:
2A33F-TWS-1
FCC ID:
1mile / 1.6km
Maximum Range
(Without Interference):
3.25” / 82.5mm
2.4” / 60.87mm
6.99” / 177.5mm
0.98” / 25mm
16' / 4.9m
PACKAGE CONTENT DIMENSION
HOW TO INSTALL
0403
LED BUTTON
OPERATION INSTRUCTIONS
ADDRESSING INSTRUCTIONS
The TWS-1 can be mounted directly on any wall
surface with appropriate fasteners to secure. (*Do not
place TWS-1 inside metal enclosures or else the signal
may be affected.)
Fasten the antenna to the wireless station
Connect the wireless station to the Hydro-X Pro’s
sensor port to connect sensors or the device port to
connect device modules wirelessly.
There is a manual push-button and a LED indicator on
the TWS-1 antenna side. The button can be used to pair
the wireless station to the controller or to reset the
addressing between sensors or device modules and the
TWS-1 itself.
make sure that your HCS-2 controller is updated to
the most recent firmware.
Connect the TrolMaster Wireless Station (TWS-1) to
the Hydro-X Pro (HCS-2) Sensor port.
Press and release the button quickly on the TWS-1 to
pair the TWS-1 to the main controller. A “pairing
successful” message will appear on the HCS-2 display
when successful.
LED Indication Message
No Light No Power
Stand ByFlashing Green
Pairde to ControllerSolid Green
How to add the TWS-1 to the Hydro-X Pro
TWS-1
0605
Hydro-X Pro Control System
01:30pm Jan 15,2022
Wireless Station
Light
Temp
Humid
CO2
Devices
Advanced
Historical Chart
Zone1 Wireless Station is
Added
OK
WIRELESS PARING INSTRUCTIONS
On the HCS-2 controller screen, go to "Setting" and
tab down to the next page. Then go to the “Wireless
Station” menu. If the icon does not appear, try pairing
again.
Press the “Add" button in the top-rigth corner to add a
new device.
Device(s) will show up on the "Scanning New Device"
window with the paring ID provided.
0807
General Alarm Setting Calibration
System Reset Screen Lock
Deadband
Import / Export Serial Number
Hydro-X Pro Control System
01:30pm Jan 15,2022
Detectors
Light
Temp
Humid
CO2
Devices
Advanced
Historical Chart
Hydro-X Pro Control System
01:30pm Jan 15,2022
Wireless Station
Light
Temp
Humid
CO2
Devices
Advanced
Historical Chart
Hydro-X Pro Control System
01:30pm Jan 15,2020
Wireless Station
Hydro-X Pro Control System
01:30pm Jan 15,2022
Add
Light
Temp
Humid
CO2
Devices
Advanced
Historical Chart
Add New Device All
CancelSave
A67B
Once the device(s) is paired, it will show up in the
"Wireless Station" menu.
CAUTION: For instructions on how to pair the specific
device/sensor to the TWS-1, please check the manual
from the device/sensor unit.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired
operation.
1009
FCC Statement
Note: This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio
frequency energy, and if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is
no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and
receiver.
– Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV
technician for help.
This equipment complies with FCC radiation exposure
limits set forth for an uncontrolled environment. This
equipment should be installed and operated with a
minimum distance of 20cm between the radiator & your
body. This transmitter must not be co-located or
operating in conjunction with any other antenna or
transmitter.
Hydro-X Pro Control System
01:30pm Jan 15,2020
Wireless Station
Channel: 122 V2.0
Hydro-X Pro Control System
01:30pm Jan 15,2020
Add
Light
Temp
Humid
CO2
Devices
Advanced
Historical Chart
Smart
Junction Box
Zone 1
Enter
12
11
ISED Canadia Statement
WARNING: Any changes or modifications not expressly
approved by the party responsible for compliance could
void the user's authority to operate the equipment.
This equipment complies with the FCC RF radiation
exposure limits set forth for an uncontrolled environ-
ment. This equipment should be installed and operated
with a minimum distance of 20cm between the radiator
and any part of your body.
(1) L’appareil ne doit pas produire de brouillage;
(2) L’appareil doit accepter tout brouillage radioélec-
trique subi, même si le brouillage est susceptible d’en
compromettre le fonctionnement.
The device meets the exemption from the routine
evaluation limits in section 2.5 of RSS-102 and compli-
ance with RSS-102RF exposure, users can obtain
Canadian information on RF exposure and compliance.
Le dispositif rencontre l'exemption des limites courantes
d'évaluation dans la section 2.5de RSS-102 et la
conformité à l'exposition de RSS-102rf, utilisateurs peut
obtenir l'information canadienne sur l'exposition et la
conformité de rf.
This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter. This
equipment should be installed and operated with a
minimum distance of 20 centimeters between the
radiator and your body.
Cet émetteur ne doit pas être Co- placé ou ne fonction-
nant en même temps qu'aucune autre antenne ou
émetteur. Cetéquipement devrait être installé et
actionné avec une distance minimum de 20 centimètres
entre le radiateur et votre corps.
This Class B digital apparatus complies with Canadian
ICES-003. Cet appareil numérique de classe B est
conforme à la normeI CES-003 du Canda.
This device contains licence-exempt transmitter(s) that
comply with Innovation, Science and Economic
Development Canada’s licence-exempt RSS(s). Operation
is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including
interference that may cause undesired operation of the
device.
L’émetteur/récepteur exempt de licence contenu dans le
présent appareil est conforme aux CNR d’Innovation,
Sciences et Développement économique Canada
applicables aux appareils radio exempts de licence.
L’exploitation est autorisée aux deux conditions
suivantes:
13
WARNING : DO NOT allow the TrolMaster
Wireless Station to be exposed to water or
excessive heat. DO NOT open or attempt to repair
or disassemble the module, as there are no
user-serviceable parts inside. Opening the module
will void the warranty.
If the surface of the TrolMaster Wireless Station is
dirty, wipe it with a dry towel. The TrolMaster
Wireless Station operates under natural ventilation
conditions.
AVERTISSEMENT : NE PAS exposer la station
sans fil TrolMaster à l'eau ou à une chaleur
excessive. NE PAS ouvrir ni tenter de réparer ou de
démonter le module, car il ne contient aucune pièce
réparable par l'utilisateur. L'ouverture du module
annulera la garantie.
Si la surface de la station sans fil TrolMaster est
sale, essuyez-la avec une serviette sèche. La station
sans fil TrolMaster fonctionne dans des conditions
de ventilation naturelle.
If you have any questions,please contact us:
TrolMaster Agro Instruments Co.,Ltd. 64 N Mission Dr, Pueblo West, CO
81007
AUG 2022 ©TrolMaster
Room 2520, 25/F., New Tech Plaza, No.34 Tai yau Street,
Kowloon, Hong Kong, China
CONFORMS TO
UL STD.62368-1
CERTIFIED TO CSA
STD.C22.2#62368-1
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7

TrolMaster TWS-1 Manuel utilisateur

Marque
TrolMaster
Modèle
TWS-1
Taper
Manuel utilisateur
Télécharger le PDF
rapport

dans d''autres langues

Autres documents