Osaki Sigma Guide d'installation

Os Pro-3D Sigma

1-2

3-4

5

7

6

Industry Canada Notice

8

9-11

12-14

15-16

17-24

25

26

27

28

Keep Dry – Do not operate in a wet or moist condition.

1

Temperatures sufficiently high to cause burns may occur regardless of the control

setting. Do not use on an infant or invalid or on a sleeping or unconscious person.

Do not use on insensitive skin or on a person with poor blood circulation. Check the

skin in contact with the heated area of the appliance frequently to reduce the risk of

blistering.

Do Not Crush – Avoid sharp folds.

Do not use massager in close proximity to loose clothing or jewelry.

Keep long hair away from massager while in use.

2

3

4

Caution

5

6

This device complies with Industry Canada licence-exempt RSS standard(s).

1. Operation is subject to the following two conditions:

(1) this device may not cause interference, and

(2) this device must accept any interference, including interference that may cause

undesired operation of the device.

2.Changes or modifications not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

Avis d’Industrie Canada

Le présent appareil est conforme avux CNR d'Industrie Canada applicables aux

appareils radio exempts de licence.

1L'exploitation est autorisée aux deux conditions suivantes :

(1) l'appareil ne doit pas produire de brouillage, et

(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi,

même si le brouillage est susceptible d'en compromettre le fonctionnement.

2.Cet appareil numérique ne dépasse pas les Rèlements sur l’interférence radio

par un appareil numérique de classe B stipulées dans les Rèlements sur

l’interférence redio d’industrie Canada.

Industry Canada Notice

7

8

Waist massage section

Bluetooth Music Speaker

8

63 9

9

54.3

34.3

51.6

23.2 20.1

22.8

10

Connect the electrical connector: B1(on the legrest) and B2(on the main unit).

AA

B1

B2

A2

A1

A2B1 B2 A1

Step 2: Install

on the legrest on the main unit

11

C

C C

on the legrest on the main unit

12

If an object is detected around the footrest, there will be the following caution!

13

14

1.When you encounter any problems and need to stop the massage immediately,

please press this button, and the massage chair will stop all actions.

2.User can adjust backrest recline by touching the icon.

3.User can adjust backrest incline by touching the icon.

4.User can adjust footrest incline by touching the icon.

5.User can adjust footrest recline by touching the icon.

6.The button for the footrest allows you to extend the length of the footrest.

7.The button for the footrest allows you to retract the length of the footrest.

15

1

4

5

2

3

7

6

AUTO

ON/OFF Button

Touch screen

(Main operation page)

Touch keys

16

Press this key to start the massage chair. Backrest and footrest of the massage

chair are automatically adjusted to the default angle. The remote control enters to

the main operation page.

Press this key again. Massage function stops. The massage mechanism, backrest

and footrest restore to its original position. The massage chair is turned off.

There are 7 massage functions available:

• Auto

• Manual

• Local

• Air Massage

• Avanced

• Settings

• Bluetooth button

Position: Press to adjust angles of the massage chair and zero gravity position.

Main operation page: Press to return to the main operation page.

Pause

Press this button to stop all the functions immediately.

Button light will be on when pause function is activated.

Please press again to cease pause function before using any other functions

AUTO: Press to start ‘Auto’

massage function (Press to start the auto massage program of Office PRO.).

3. The manual controller is described as follows

Main Operation Page

AUTO

Main operation page

Pause

AUTO

Position

17

1.Select 'Auto' function on the operation main page.

2.There are 15 massage modes to select from. After the selection, relevant massage

starts. The remote control enters to the adjustment page.

3. The adjustment page.

4.Body scanning will commence when the program is selected. ( Screen will show

scanning).

5.Please sit as far back in the seat as possible with your head on the pillow during

the scanning.

1 . 3D : Touch 3D to adjust 3D massage intensity ( 6 levels).

2 . Strength : Touch Strength to adjust Kneading strength ( 5 levels).

3 . Speed : Touch Speed to adjust Tapping speed ( 5 levels ).

4 . Intensity : Touch Intensity to adjust air massage intensity ( 5 levels ).

‘Auto’ Massage

Adjustment notes

18

La page charge ...

Osaki Sigma Guide d'installation

Osaki Sigma Guide d'installation

dans d''autres langues

Autres documents