Sony KE-P37XS1 Le manuel du propriétaire

Operating Instructions

GB

Before operating the TV, please read the “Safety Information”

section of this manual. Retain this manual for future reference.

R

4-102-916-11 (1)

PDP Colour TV

KE-P37XS1

KE-P42XS1

Bedienungsanleitung

DE

Bevor Sie das Fernsehgerät einschalten, lesen Sie bitte den

Abschnitt „Sicherheitshinweise“ dieses Handbuchs. Bewahren

Sie das Handbuch auf, um später bei Bedarf darin nachschlagen

zu können.

Manual de Instrucciones

ES

Antes de utilizar este televisor, lea atentamente el capítulo

“Normas de seguridad” de este manual. Conserve el manual para

futuras referencias.

Mode d'emploi

FR

Avant d'utiliser le téléviseur, nous vous prions de lire avec

attention les “Consignes de sécurité illustrées à la section

correspondante de ce manuel. Conservez ce manuel pour vous y

référer ensuite.

2

NOTICE FOR CUSTOMERS IN THE UNITED

KINGDOM AND IRELAND

A moulded plug complying with BS1363 is fitted to this equipment for your safety and convenience.

Should the fuse in the plug supplied need to be replaced, a 5 AMP fuse approved by ASTA or BSI to BS

1362 (i.e. marked with or ) must be used.

When an alternative type of plug is used it should be fitted with a 5 AMP FUSE, otherwise the circuit

should be protected by a 5 AMP FUSE at the distribution board.

If the plug supplied with this equipment has a detachable fuse cover, be sure to attach the fuse cover after

you change the fuse. Never use the plug without the fuse cover. If you should lose the fuse cover, please

contact your nearest Sony service station.

How to replace the fuse

Open the fuse compartment with a blade screwdriver, and replace the fuse.

• IMPORTANT

If the plug supplied is not suitable for the socket outlets in your home, it should be cut off and

an appropriate plug fitted in accordance with the following instructions:

The wires in this mains lead are coloured in accordance with the following code:

Blue Neutral

Brown Live

As the colours of the wires in the mains lead of this apparatus may not correspond with the

coloured markings identifying the terminals in your plug, proceed as follows:

The wire which is coloured blue must be connected to the terminal which is marked with the

letter N or coloured black. The wire which is coloured brown must be connected to the

terminal which is marked with the letter L or coloured red. Do not connect either wire to the

earth terminal in the plug which is marked by the letter E or by the safety earth symbol I

or coloured green or green and yellow.

WARNING

• To prevent the risk of electric shock, do not insert the plug cut off from the mains lead into a

socket outlet. This plug cannot be used and should be destroyed.

• To prevent the risk of fire or electric shock, do not expose the unit to rain or moisture.

• Dangerously high voltages are present inside the set. Do not open the cabinet. Refer servicing

to qualified personnel only.

FUSE

3

GB

Introduction

• Thank you for choosing this Sony product.

• Before operating the TV, please read this manual thoroughly and retain it for future reference.

• Symbols used in the manual:

Table of Contents

Notice for Customers in the United Kingdom and Ireland................................................................................... 2

Introduction .......................................................................................................................................................... 3

Safety Information................................................................................................................................................4

Precautions ........................................................................................................................................................... 7

Overview & Installation

Checking the Accessories Supplied......................................................................................................................9

Overview of Remote Control Buttons................................................................................................................ 10

Overview of the TV Buttons and side Connectors............................................................................................. 12

Overview of the TV Indicators...........................................................................................................................13

Inserting Batteries into the Remote Control.......................................................................................................13

Connecting the Aerial and VCR.........................................................................................................................14

Stabilizing the TV set ........................................................................................................................................ 14

First Time Operation

Switching on the TV and Automatically Tuning ...............................................................................................15

TV Functions

Introducing and Using the Menu System ..........................................................................................................17

The Picture Adjustment menu .....................................................................................................................18

The Sound Adjustment menu....................................................................................................................... 20

The Features menu........................................................................................................................................ 22

The Timer menu ........................................................................................................................................... 25

The Set Up menu.......................................................................................................................................... 26

"Memory Stick"

About "Memory Stick"....................................................................................................................................... 30

Adjusting settings...............................................................................................................................................31

Viewing Photos and Playing movies..................................................................................................................33

Teletext.................................................................................................................................................................. 36

NexTView...............................................................................................................................................................37

Additional Information

Connecting Equipment to the TV........................................................................................................................38

Viewing pictures from equipment connected to the TV......................................................................................40

Remote Control Configuration for VCR or DVD ...............................................................................................41

Learning functions from other Remote controls..................................................................................................42

Technical Specifications......................................................................................................................................44

Troubleshooting...................................................................................................................................................45

Television Channdel Number Guide...................................................................................................................49

Index....................................................................................................................................................................50

How to lift the TV ................................................................................................................................Back cover

• Buttons shaded white on the remote control show you the

buttons you have to press to follow the sequence of the

instructions.

• Informs you of the result of the instructions.

• Important information.

• Information on a feature.

• 1,2... Sequence of instructions.

Table of Contents

4

Safety Information

Ventilation

Leave space around the TV set. Otherwise, adequate

air-circulation may be blocked causing overheating

which may cause fire or damage the TV set.

Table 1:

Mains lead

Unplug the mains lead when

moving the set. Do not move

the set with the mains lead

plugged in. It may damage the

mains lead and result in fire or

electric shock. If the set has been dropped or

damaged, have it checked immediately by qualified

service personal.

Medical institution

Do not place this TV set in a

place where medical

equipment is in use. It may

cause malfunction of medical

instruments.

Damage requiring service

If the surface of the display cracks, do not touch it

until you have unplugged the mains lead. Otherwise

electric shock may result.

Carrying

Carrying the TV requires two or

more people. If you carry the TV

in a manner other than that

specified, it may drop and a

serious injury may be caused. Be

sure two or more people carry the TV. When

transporting, do not subject the TV set to shocks or

excessive vibration. The TV may fall and be damaged

or cause serious injury.

Leave at

least

this

much

space.

30cm

10cm10cm

10cm

Safety Information

continued...

5

GB

Power Sources

Overloading

This set is designed to operate on

a 220-240V AC supply only.

Take care not to connect too

many appliances to the same

mains socket as this could result

in fire or electric shock.

Mains lead protection

Pull out the mains lead by the

plug. Do not pull on the mains

lead itself.

Mains

Do not use a poor fitting mains socket. Insert

the plug fully into the mains. If it is loose, it

may cause arcing and result in fire. Contact

your electrician to have the mains socket

changed.

Wiring

Unplug the mains lead when wiring cables. Be sure to

unplug the mains lead for your safety, when hooking up.

Moisture

Do not touch the mains lead with a wet

hand. If you plug/unplug the mains lead

with a wet hand, it may cause electric

shock.

Cleaning

Clean the mains plug regularly. If the

plug is covered with dust and it picks up

moisture, its insulation may deteriorate

and result in fire. Unplug the mains plug

and clean it regularly.

Lightning storms

For your own safety, do not touch

any part of the set, mains lead or

aerial lead during lightning storms.

When not in use

For environmental and safety

reasons, it is recommended that

the set is switched off when not

in use - not left in standby

mode. Disconnect from the

mains.

Mains lead

If you damage the mains lead, it

may result in fire or electric

shock.

• Do not pinch, bend, or twist the

cable excessively. The core

lines may be bared or cut,

causing a short - circuit which

may in fire or electric shock.

• Do not convert or damage the

mains lead.

• Do not put anything heavy on the mains lead. Do not

pull the mains lead.

• Keep the mains lead away from heat sources.

• Be sure to grasp the plug when disconnecting the

mains lead.

• If the mains lead is damaged, stop using it and ask your

dealer or Sony service centre to exchange it.

Cable wiring

Take care not to catch your feet on the cables. It may

damage the TV set.

Installation

• Do not install optional components too close to the

TV set. Keep optional components at least 30 cm

away from the TV set. If a VCR is installed in front or

at the right side of the TV set, the picture may distort.

Heat

Do not touch the surface of the TV. It remains hot, even

after the TV has been turned off for some time.

Electric shock

Do not touch the TV set with wet hands. Doing so may

cause electric shock or damage the TV set.

Oils

Do not install TV set in restaurants that use oil. Dust

absorbing oil may enter into the TV set and damage TV

set.

Corrosion

If you use this set near the seashore, salt may corrode

metal parts of the TV set and cause internal damage or

fire. It may also shorten the life of the TV set. Steps

should be taken to reduce the humidity and temperature

of the area where the set is located.

Safety Information

continued...

6

Installation and moving

Ventilation

Never cover the ventilation holes in the

cabinet. It may cause overheating and

result in fire. Unless proper ventilation is

provided, the TV set may gather dust and

get dirty. For proper ventilation, observe

the following:

• Do not install the TV set turned backward or sideways.

• Do not install the TV set turned over or upside down.

• Do not install the TV set on a shelf or in a closet.

• Do not place the TV set on a rug or bed.

• Do not cover the TV set with cloth, such as curtains, or

items such as news papers, etc.

Outdoor use

Do not install this TV set

outdoors. If the TV set is exposed

to rain, it may result in fire or

electric shock. If the TV set is

exposed to direct sunlight, the TV

set may heat up and it may

damage the TV set.

Vehicle or ceiling

Do not install this TV set in a

vehicle. Bumping of the vehicle

may cause the set to fall down

and cause injury. Do not hang this

TV set from the ceiling.

Ships and other vessels

Do not install this TV set in a

ship or vessel. If the TV set is

exposed to seawater, it may

cause fire or damage the TV set.

Water and moisture

Do not use this TV set near water - for example, near a

bathtub or shower room. Also do not expose to rain. It

may result in fire or electric shock.

To prevent the TV set from falling

Place the TV set on a secure, stable stand

and secure the TV set to a wall (see page

14 for details). Do not hang anything on

the TV set. The TV set may fall from the

stand or wall-hanging rack unit, causing damage or

serious injury.

Servicing

Do not open the cabinet or

remove the rear cover of the set.

Refer to qualified service

personnel only.

Ventilation holes

Do not insert anything in the ventilation

holes. If metal or something flammable

enters, it may result in fire or electric

shock.

Moisture and flammable objects

• Do not let this set get wet. Never

spill liquid of any kind on the set. If

any liquid or solid object does fall

through, do not operate the set. It

may result in electric shock or damage to the set. Have

it checked immediately by qualified personnel.

• To prevent fire, keep inflammable objects or naked

lights (e.g. candles) away from the set.

Broken glass

Do not throw anything at the TV set.

The screen glass may explode by the

impact and cause serious injury.

Protruding location

Do not install the TV set in protruding locations. If you

install the TV set in the following locations, it may result

in injury.

• Do not install the TV set in a location where the TV

set protrudes, such as on or behind pillar.

• Do not install the TV set in a location where you

might bump your head on it.

Placement

Never place the set in hot, humid or

excessively dusty places. Do not

install the set where it may be

exposed to mechanical vibrations.

Cleaning

Unplug the mains lead when cleaning this TV set. If not,

it may result in electric shock.

Safety Information

continued...

7

GB

Precautions

On viewing the TV comfortably

• To view the TV comfortably, the recommended viewing position is from four to seven times of the screen’s

vertical length away from the TV set.

• View the TV in a moderate light room, as viewing the TV in poor light taxes your eyes. Watching the screen

continuously for long periods of time can also tax your eyes.

On installing the TV set

• Do not install the TV in places subject to extreme temperature, for example in direct sunlight, or near a radiator,

or heating vent. If the TV set is exposed to extreme temperature, the TV set may heat up and it may cause

deformations of the casing or cause the TV set to malfunction.

• After transporting the TV directly from a cold to a warm location, or if the room temperature has changed

suddenly, pictures may be blurred or show poor colour over portions of the picture. This is because moisture has

condensed on the mirrors or lenses inside the TV set. In this case let the moisture evaporate before using the TV

set.

• To obtain a clear picture, do not expose the screen to direct illumination or direct sunlight. If possible, use spot

lighting directed down from the ceiling.

• The TV set is not disconnected from the mains when the switch is in Off position. To disconnect the set

completely, pull the plug from the mains.

On volume adjustment

• Adjust the volume so as not to trouble neighbours. Sound carries very easily at night time. Therefore, closing the

windows or using headphones is suggested.

• When using headphones, adjust the volume so as to avoid excessive levels, as hearing damage may result.

On handling the remote control

• Handle the remote control with care. Do not drop or step on it, or spill liquid of any kind onto it.

• Do not place the remote control in a location near a heat source, or in a place subject to direct sunlight, or in a

damp room.

On cleaning the cabinet

• Be sure to unplug the mains lead before cleaning.

• Clean the cabinet with the supplied cleaning cloth or a soft cloth lightly dampened. Do not use any type of abrasive

pad, alkaline cleaner, scouring powder or solvent, such as alcohol or benzine, or antistatic spray.

• Note that material deterioration or screen coating degradation may occur if the TV is exposed to a volatile solvent,

such as alcohol, thinner, benzine or insecticide, or if prolonged contact is maintained with rubber or vinyl

materials.

• The ventilation holes can accumulate dust over a period of time and the accumulated dust may make the cooling

function of the built-in fan less effective. To prevent this, we recommend removing the dust periodically (once a

month) using a vacuum cleaner.

On handling and cleaning the screen surface

The screen of this TV has an anti-reflection screen coating. To avoid screen degradation, follow the points mentioned

below. Do not push on or scratch with hard objects, or throw anything at the screen. The screen may be damaged.

• Be sure to unplug the mains lead before cleaning.

• Do not touch the TV after operating continuously for along period as the display panel becomes hot.

• The screen of this TV has an anti-reflection screen coating. We recommend that the screen surface is touched as

little as possible.

• Clean the screen with the supplied cleaning cloth or a soft cloth lightly moistened. Cleaning with dirty cleaning

cloth may result in damage to the TV set. Never use any type of abrasive pad, scouring powder, or solvent, such

as alcohol or benzine. This type of contact may result in damage to the screen surface.

Safety Information

continued...

8

On image

• Please note that the PDP (Plasma Display Panel) screen is made with high-precision technology. However, black

points or bright points of light (red, blue, or green) may appear constantly on the PDP screen, and irregular

coloured stripes or brightness may appear on the PDP screen. This is not a malfunction.

• With extensive use of this TV set in 4:3 mode, the 4:3 screen area might become darker within a 16:9 panel. To

avoid this problem, the “Smart” picture mode should be used (see page 22).

On image retention

• If the following images are displayed for an extended period time, image retention (afterimage) in areas of the

screen may result due to the characteristics of the Plasma Display Panel.

– Black bars at the top and bottom that appear with a wide video source (Letterbox picture).

– Black bars to the left and right that appear with a 4:3 video source (conventional TV broadcasts).

– Video game sources

–PC images

– DVD on-screen menu displays

– On-screen menus, channel numbers, etc., of connected equipment such as Set top box, Cable modem, VCR,

etc.

The risk of this is higher if the set is in “Live” mode or has a high contrast setting. This image cannot be

removed once burnt onto the screen. To avoid the risk of image retention do not leave the TV set operating

on such a picture, or programme for a long time, use the “Screen Saver” function (page 24) or lower the

contrast setting. Repeated extended daily usage of the same image, or programme can also result in this

occurrence. IMAGE RETENTION IS NOT COVERED BY THE SONY WARRANTY.

• To reduce image retention, this TV set has the “Screen Saver” function. The default setting of the “Orbit”

function in “Screen Saver” is “On” (page 24.)

• The “Screen Saver” function prevents and reduces image retention. For details see page 24.

On altitude

• When used at an altitude of greater than 2300m or 7546 feet (air pressure less than 760hPa), this Plasma TV may

generate a low buzzing sound as a result of the difference between the interior and exterior air pressure of the

panels. This is not considered a defect and is not covered under by the Sony Warranty. This buzzing sound is an

inherent characteristic of any Plasma Display Panel.

Safety Information

9

GB

Checking the Accessories supplied

1 Mains Leads (Type C-4):

Use this mains leads (with

safety earth) if you use the

set outside the United

Kingdom and Ireland.

1 Mains Leads (Type BF):

• Use this mains leads (with

safety earth) if you use the set

in the United Kingdom.

•See “NOTICE FOR

CUSTOMERS IN THE

UNITED KINGDOM and

IRELAND” on page 2

when using these mains leads.

• This mains leads may not be

supplied depending on the

country.

1 Mains Leads (Type C-5):

• Use this mains leads (with

safety earth) if you use the set

in the Swiss Confederation.

• This mains leads may not be

supplied depending on the

country.

Do not remove ferrite cores.

GB

Do not remove ferrite cores.

1 Remote control

(RM-Y1010):

2 Batteries (AA size):

Overview & Installation

1 Cleaning cloth:

1 Coaxial Cable:

2 Anchor attachments:

1 AV Mouse:

1 “Notes on Plasma” book.

1 Clump Belt:

10

Overview of Remote Control Buttons

1 TV I/ : To Temporarily Switch Off TV (standby mode):

Press this button to temporarily switch off TV (the standby indicator on the TV

lights up). Press again to switch on TV from standby mode.

• To save energy we recommend switching off completely when TV is

not in use.

• If the “Auto Shutoff” option is set to “On” (see page 25) the TV

switches automatically into standby mode after 15 minutes without a

TV signal and without any button being pressed.

2 VIDEO I/ : press this button to switch your VCR or DVD on or off.

3 Media Selector: press these buttons to select which device you want to operate,

TV, VCR, DVD or AUX. A green light will be momentarily lit to show which one

you have selected. For details refer to pages 41-43.

4 Selecting TV mode: press this button to switch off Teletext or Video input

mode.

5 Selecting input source: press this button repeatedly until the desired input

symbol of the source appears on the TV screen. Refer to page 40.

6 Switching off the picture: press this button to switch off the picture. Only the

picture is switched off; the sound remains on. Press again to cancel.

7 Selecting broadcast channels: if Media Selector (3) is switched to TV,

press these buttons to select channels. For double-digit programme numbers, enter

the second digit within 2.5 seconds.

8 a) Watching last channel selected: if Media Selector (3) is switched to

TV, press this button to return to the previous channel you were watching

(provided you watched it for at least 5 seconds).

b) Selecting VCR double-digit: if Media Selector (3) is switched to VCR,

press this button to select double-digit channels for Sony's VCR e.g. 23, press

-/-- first and next the buttons 2 and 3.

9 a) Fastext: if Media Selector (3) is switched to TV and whilst you are in

Teletext mode, these buttons can be used as Fastext buttons. For details see

page 36.

b) Operating VCR or DVD: if Media Selector (3) is switched to VCR or

DVD, these buttons will operate the main functions of your VCR or DVD,

once the remote control has been programmed. Refer to page 41.

q; Teletext: press this button to switch on Teletext. For details see page 36.

continued...

Overview & Installation

1

3

2

4

5

7

8

9

q;

6

11

GB

The buttons labelled 5, qd and qk are also used for Teletext operation. For details see page 36.

.

qa a) Displaying a channel or an input signal index: If Media Selector

(3) is switched to TV and MENU is switched off, press OK to display a

channel or input signal index. Once you have pressed OK:

1 To select a channel: press v or V to select a channel and next press

again the OK button to watch the selected channel.

2 To select an input signal: while watching the channel index, press b to

display the input signal (you can always switch from the channel index to

the input signal index and vice versa by pressing B or b). Next, press v

or

V to select an available input signal. Finally press again the OK button

to watch the selected input signal.

b) Navigator: if Media Selector (3) is switched to TV and MENU (qs) is

switched on, use these buttons to navigate through the menu system of the

TV. Refer to page 17.

qs Displaying "Memory Stick" menu: for details see pages 30-35.

qd Selecting broadcast channels: press these buttons to select the next or

previous broadcast channel.

qf Menu system: press this button to enter the TV menu system. Refer to page

17.

qg Adjusting volume: press these buttons to increase or decrease the volume.

qh Selecting the screen format: press this button repeatedly to change the

format of the screen. Refer to page 22.

qj NexTView: press this button to display NexTView. For details, refer to page

37.

qk Displaying Info: press this button to display all on-screen indication such as

channel number, etc. Press again to cancel.

ql Selecting picture mode: press this button repeatedly to change the picture

mode. For details on the different picture modes, refer to page 18.

w;

Selecting the sound effect: press this button repeatedly to change the

sound effect. For details on different sound effects refer to page 20.

wa Muting the sound: press this button to mute the TV sound. Press again to

restore the sound.

Overview & Installation

wa

w;

qf

qg

qj

qk

ql

qh

qa

qd

qs

12

Overview of the TV Buttons and side Connectors

On/Off switch

Volume control buttons (+/-)

Programme Up or Down buttons

(selects TV channels)

TV mode button

Selecting Input Source button

(see page 40)

(MONO)

L/G/S/I

R/D/D/D

Overview of the TV Buttons

Overview of the side Connectors

Headphones

jack

Video Input

jack

S Video Input

jack

Audio Input

jacks

Auto Start Up button (starts

the auto start up sequence, see

page 15)

Overview & Installation

13

GB

Overview & Installation

Overview of the TV indicators

Inserting Batteries into the Remote Control

Make sure you insert the supplied batteries using the correct polarities.

Always remember to dispose of used batteries in an environmental friendly way.

To operate

the remote

control, point

it towards

this receiver.

Lights up in blue when you

press (picture off) on

the remote control to

switch off the picture. Only

the picture is switched off

(the sound remains

unchanged).

Lights up in red

when the sleep

timer is set. For

more details

regarding the sleep

timer, refer to “

Timer” on

page 25.

Lights up in

green when

the TV is

switched on.

Lights up in red

when the TV is in

standby mode.

14

Connecting the Aerial and VCR

Stabilizing the TV set

After setting up, secure the TV set to a wall, pillar, etc, using the supplied anchor attachments, for safety

purposes.

1 Remove the two screws attached to the upper rear side

of the TV set.

2 Replace the two screws with the two supplied anchor

attachments.

3 Secure a wall anchor bracket (not supplied) to a solid wall or

pillar.

4 Pass a strong cord or chain through both holes of the anchor

attachments and then secure to a wall or pillar, etc.

• Use the supplied mains lead (Type C-4, Type BF or Type C-5, see page 9).

• Use the supplied coaxial cable for aerial connection.

or

For more details regarding VCR connection, refer to

“Connecting Optional Equipment to the TV” on

page 38.

OUT IN

VCR

Overview & Installation

15

GB

1 Connect the TV plug to the mains socket (220-240V

AC, 50Hz).

2 The first time that the TV set is connected, it is usually

turned on. If the TV is off, press the on/off button on

the TV set to turn on the TV.

The first time you switch on the TV, a Language

menu appears automatically on the TV screen.

3 Press the V, v, B or b buttons on the remote control to select your

language, then press the OK button to confirm your selection. From

now on all the menus will appear in your chosen language.

4 The Country menu appears automatically. Press the v or V button

to select the country in which you are using the TV. Press the OK

button to confirm your selection.

• If the country in which you want to use the TV set does not

appear in the list, select “Off” instead of a country.

• To avoid wrong teletext characters for cyrillic languages we

recommend selecting Russia if your own country does not

appear in the list.

Switching On the TV and Automatically Tuning

The first time you switch on your TV, a sequence of menu screens appear on the TV enabling you to: 1) choose

the language of the menu screen 2) Choose the country in which you are going to operate the TV, 3) check how

to connect optional equipment to your TV, 4) search and store all available channels (TV Broadcast) and 5)

change the order in which the channels (TV Broadcast) appear on the screen.

However, if you need to change any of these settings at a later date, you can do that by selecting the appropriate

option in the (Set Up menu) or by pressing the Auto Start Up button on the right side of TV set.

First Time Operation

continued...

Country

Select country

Off

Ireland

Nederland

België/Belgique

Luxembourg

France

Italia

Schweiz/Suisse/Svizzera

16

5 A diagram appears showing you how to connect a wide range of

equipment to your TV set. Follow the instructions and press the

OK button to remove the picture and continue the automatic

process.

The connection diagram should be used as a guide only as

most equipment can be connected to more than one type of

TV socket. Once the TV has completed the automatic

tuning process, refer to the ‘Connection Guide’ section on

page 23 for further information on getting the best set up for

your equipment.

6 The Auto Tuning menu appears on the screen. Press the OK

button to select Yes.

7 The TV starts to automatically search and store all

available broadcast channels for you.

This procedure could take some minutes. Please be patient

and do not press any buttons, otherwise automatic tuning

will not be completed.

In some countries the TV Broadcaster installs the channels

automatically (ACI system). In this case, the TV

Broadcaster sends a menu in which you can select your city

by pressing the

v or V button and OK to store the

channels.

If no channels were found during the auto tune process, a

message appears automatically on the screen asking you to

connect the aerial. Check the aerial connection (refer to

page 14). Press the OK button to restart the auto tuning

process.

8 After all available channels are captured and stored,

the Programme Sorting menu automatically appears

on the screen enabling you to change the order in

which the channels are stored.

a) If you wish to keep the broadcast channels in the tuned order,

go to step 9.

b) If you wish to store the channels in a different order:

1 Press the v or V button to select the programme

number with the channel (TV Broadcast) you wish

to move. Press the b button.

2 Press the v or V button to select the new

programme number position for your selected

channel (TV Broadcast). Press the OK button to store.

3 Repeat steps b)1 and b)2 if you wish to change

the order of the other channels.

9 Press the MENU button to remove the menu from the screen

Auto Tuning

Programmes found: 4

No channel found.

Please connect aerial

Confirm

Programme Sorting

01

02

03

04

05

06

07

08

TVE

TVE2

TV3

C33

C27

C58

S02

S06

Programme Sorting

01 TVE

01

02

03

04

05

06

07

08

TVE

TVE2

TV3

C33

C27

C58

S02

S06

Do you want to start

automatic tuning?

Yes No

OK

Please connect your equipment

according to this chart

DVD

Your TV set is now ready for use

First Time Operation

17

GB

Introducing and Using the Menu System

Your TV set uses an On-Screen menu system to guide you through the operations. Use the following buttons

on the Remote Control to operate the menu system:

1 To switch on the menu screens:

Press the MENU button to switch the first level menu on.

TV Functions

2 To navigate through the menus:

• To highlight and select the desired menu or option, press

v or V.

• To enter the selected menu or option, press OK or

b.

• To return to the last menu or option, press OK or

B.

• To alter the settings of your selected option, press

v/V/B or b.

• To confirm and store your selection, press OK.

3 To switch off the menu screens:

Press the MENU button to remove the menu from the screen.

18

The Picture Adjustment Menu

The “Picture Adjustment” menu allows you to

alter the picture settings.

To do this:

Press the MENU button and then press OK to

enter this menu. Next, press

v or V to select the

desired option and press OK. Finally, read below

how to operate into each option.

Picture Mode This option allows you to customise the Picture Mode based on the programme

you are watching. After selecting this option press OK. Next, press repeatedly

v

or

V to select:

Live (for live broadcast programmes, DVD and Digital Set Top Box

receivers).

Movie (for films).

Personal (for individual settings).

Once you have selected your desired option, press OK to store.

"Brightness", "Colour" and "Sharpness" level of "Live" and "Movie" mode are fixed on the

factory to get the best picture quality.

Contrast Press B or b to reduce or enhance picture contrast. Next, press OK to store.

Brightness Press B or b to darken or brighten the picture. Next, press OK to store.

This option only appears and can only be adjusted if “Picture Mode” is set to “Personal”.

Colour Press B or b to decrease or to increase color intensity. Next press OK to store.

This option only appears and can only be adjusted if “Picture Mode” is set to “Personal”.

Hue Press B or b to decrease or to increase the green tones. Next press OK to store.

This option only appears for NTSC signal (e.g. USA video tapes).

Sharpness Press B or b to soften or to sharpen the picture. Next press OK to store.

This option only appears and can only be adjusted if “Picture Mode” is set to “Personal”.

TV Functions

,

MENU

continued...

19

GB

Reset Press OK to reset the picture to the factory preset levels.

Noise This option is set to Auto to automatically reduce the snowy picture visible in the weak broadcast

Reduction signal. However, it can be modified. After selecting this option press

b. Next, press v or V to

select High, Mid, Low or Off. Finally, press OK to store.

Colour Tone This option allows you to alter the tint of the picture. After selecting this option press b. Next, press

repeatedly

v or V to select: Warm (gives the white colours a red tint), Normal (gives the white

colours a neutral tint), Cold (gives the white colours a blue tint). Finally press OK to store.

DRC Mode This option allows you to select the high resolution picture with 4x density for high quality sources

(i.e. DVD player, satellite receiver). This option is set to High Density (recommended for moving

pictures). However it can be modified. After selecting this option, press

b. Next press v or V to

select Progressive (recommended for still images and text).

This option only appears and can only be adjusted if “Picture Mode” is set to “Personal”.

DRC Palette This option allows you to customise the level of detail (Reality) and smoothness (Clarity) for up to

three input sources. After selecting this option press

b. Next, press v or V, to adjust Reality (as

higher as the mark is along the Reality axis, the picture becomes more detailed) and press

B or

b to adjust Clarity (as you move to the right, along the Clarity axis, the picture becomes

smoother). Finally, press OK to store.

This option only appears and can only be adjusted if “Picture Mode” is set to “Personal”.

TV Functions

20

The Sound Adjustment Menu

The “Sound Adjustment” menu allows you to

alter the sound settings.

To do this:

Press the MENU button and press

v to select

, then press OK to enter this menu. Next,

press

v or V to select the desired option and

press OK. Finally, read below how to operate

into each option.

Sound This option allows you to customise the Sound Effect. After selecting this

Effect option press OK. Next, press repeatedly

v or V to select:

Dolby* (Dolby Virtual, simulates the sound effect of “Dolby Surround Pro

Virtual Logic”).

Natural (Enhances clarity, detail and presence of sound by using “BBE High

Definition Sound system”**).

Dynamic (“BBE High Definition Sound system”** intensifies clarity and presence

of sound for better intelligibility and musical realism).

Off (Flat response).

Once you have selected your desired option, press OK to store.

Treble Press B or b to decrease or to increase higher-frequency sounds. Next, press OK to

store.

Bass Press B or b to decrease or to increase the lower-frequency sounds. Next, press OK

to store.

Balance Press B or b to emphasise the left or the right speaker. Next, press OK to store.

Reset Press OK to reset the sound to the factory preset levels.

Dual Press b. Next:

Sound • For a Stereo broadcast:

Press

v or V to select Stereo or Mono. Next press OK to store.

• For a bilingual broadcast:

Press

v or V to select Mono (for mono channel if available), A (for channel 1) or B

(for channel 2). Next press OK to store.

Auto Press b. Next press v or V to select On (the volume level of the channels will

Volume stay the same, independent of the broadcast signal, e.g. in the case of advertisements)

or Off (the volume level changes according to the broadcast signal). Next press OK to

store.

If you select “Dolby Virtual” on the “Sound Effect” option, the “Auto Volume” option will

automatically be switched to “Off”.

continued...

TV Functions

,

m

MENU

La page charge ...

Sony KE-P37XS1 Le manuel du propriétaire

Ce manuel convient également à

Sony KE-P37XS1 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents