Sony KLV-30MR1 Manuel utilisateur

4-094-069-11 (1)

LCD Colour TV

KLV-30MR1

 2003 Sony Corporation

Operating Instructions

Bedienungsanleitung

Manual de instrucciones

Mode d’emploi

GB

DE

FR

NL

2

NOTICE FOR CUSTOMERS IN THE UNITED KINGDOM

A moulded plug complying with BS1363 is fitted to this equipment for your safety and convenience.

Should the fuse in the plug supplied need to be replaced, a 5 AMP fuse approved by ASTA or BSI to BS

1362 (i.e. marked with or ) must be used.

When an alternative type of plug is used it should be fitted with a 5 AMP FUSE, otherwise the circuit

should be protected by a 5 AMP FUSE at the distribution board.

If the plug supplied with this equipment has a detachable fuse cover, be sure to attach the fuse cover after

you change the fuse. Never use the plug without the fuse cover. If you should lose the fuse cover, please

contact your nearest Sony service station.

How to replace the fuse

Open the fuse compartment with a blade screwdriver, and replace the fuse.

IMPORTANT

If the plug supplied is not suitable for the socket outlets in your home, it should be cut off and an

appropriate plug fitted in accordance with the following instructions:

The wires in this mains lead are coloured in accordance with the following code:

Blue Neutral

Brown Live

As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured

markings identifying the terminals in your plug, proceed as follows:

The wire which is coloured blue must be connected to the terminal which is marked with the letter N or

coloured black. The wire which is coloured brown must be connected to the terminal which is marked with

the letter L or coloured red. Do not connect either wire to the earth terminal in the plug which is marked

by the letter E or by the safety earth symbol I or coloured green or green and yellow.

WARNING

• To prevent the risk of electric shock, do not insert the plug cut off from the mains lead into a socket

outlet. This plug cannot be used and should be destroyed.

• To prevent the risk of fire or electric shock, do not expose the unit to rain or moisture.

• Dangerously high voltages are present inside the set. Do not open the cabinet. Refer servicing to

qualified personnel only.

3

Table of Contents

GB

Introduction

Thank you for choosing this Sony LCD Colour Television.

Before operating the TV, please read this manual thoroughly and retain it for future reference.

Symbols used in the manual

Table of Contents

Safety Information

Safety Information .....................................................................................................................................5

Precautions ............................................................................................................................................... 11

Overview

Checking the Accessories Supplied ......................................................................................................... 13

Overview of the Display Unit .................................................................................................................. 14

Overview of the Media Receiver Unit Buttons and Indicators ...............................................................15

Overview of the Remote Control Buttons ............................................................................................... 16

Installation

Inserting Batteries into the Remote Control ............................................................................................18

Connecting the Display Unit to the Media Receiver Unit .......................................................................19

Storing the cables in the display stand .....................................................................................................21

Connecting the Aerial and VCR .............................................................................................................. 22

First Time Operation

Switching On the TV and Tuning the TV Automatically .......................................................................23

Menu System

Introducing and Using the Menu System ................................................................................................26

Picture Adjustment ..................................................................................................................................26

Sound Adjustment ...................................................................................................................................28

Screen Control ......................................................................................................................................... 30

Features .................................................................................................................................................... 33

Set Up ...................................................................................................................................................... 36

Timer ....................................................................................................................................................... 40

Unit Status ............................................................................................................................................... 42

“Memory Stick”

About “Memory Stick” ............................................................................................................................43

Inserting and Removing a “Memory Stick” ............................................................................................ 46

Using the “Memory Stick” (Memory Stick Home) ................................................................................. 47

.........Important information.

.........Information on a feature.

1,2 ...........Sequence of instructions.

....Shaded buttons on the remote control

show you the buttons you have to press

to follow the sequence of instructions.

..........Informs you of the result of instructions

followed.

OK

(continued)

4

Table of Contents

Teletext

Teletext ....................................................................................................................................................55

NexTView

NexTView* .............................................................................................................................................56

Additional Information

Connecting Optional Equipment ............................................................................................................. 59

Using Optional Equipment ...................................................................................................................... 63

Remote Control Configuration for VCR/DVD .......................................................................................64

Specifications ...........................................................................................................................................66

Troubleshooting .......................................................................................................................................69

Television Channel Number Guide for United Kingdom ................................................................. 74

5

Safety Information

GB

Safety Information

For Safety

Mains lead and display cable

Unplug the mains lead and the

display cable when moving

the set. Do not move the set

with the mains lead and the

display cable plugged in. It

may damage the mains lead

and the display cable and result in fire or electric shock.

If the set has been dropped or damaged, have it checked

immediately by qualified service personal.

Medical institution

Do not place this unit

in a place where

medical equipment is

in use. It may cause

malfunction of

medical instruments.

For the display unit

Installation

Installation of the display

unit on the wall should be

carried out by qualified

servicemen. Improper

installation may render the

unit unsafe in the event of an

earthquake, etc.

Carrying

Carrying the display unit

requires two or more people.

If you carry the display unit

in a manner other than that

specified, it may drop and a

serious injury may be caused. Be sure two or more

people carry the display unit. When transporting, do

not subject the display unit to shocks or excessive

vibration. The display unit may fall and be damaged

or cause serious injury. When you carry the display

unit for repair or when you move it, pack it using the

original carton and packing material.

(continued)

6

Safety Information

Installation and moving

Ventilation

Never cover the ventilation holes in the

cabinet. It may cause overheating and

result in fire. Unless proper ventilation

is provided, the unit may gather dust

and get dirty. For proper ventilation,

observe the following:

• Do not install the unit turned backwards or sideways.

• Do not install the unit turned over or upside down.

• Do not install the unit on a shelf or in a closet.

• Do not place the unit on a rug or bed.

• Do not cover the unit with cloth, such as curtains, or

items such as news papers, etc.

Outdoor use

Do not install this unit

outdoors. If the unit is

exposed to rain, it may

result in fire or electric

shock. If the unit is

exposed to direct

sunlight, the unit may

heat up and it may damage the unit.

Vehicle or ceiling

Do not install this unit in a

vehicle. Bumping of the

vehicle may cause the set to

fall down and cause injury.

Do not hang this unit from

the ceiling.

Ships and other

vessels

Do not install this unit

in a ship or vessel. If

the unit is exposed to

seawater, it may cause

fire or damage the unit.

Water and moisture

Do not use this unit near water - for example, near a

bathtub or shower room. Also do not expose to rain,

moisture or smoke. It may result in fire or electric shock.

Do not use this unit where insects may enter.

For the display unit

Optional accessories

Observe the following when installing

the display unit using a stand or wall-

mount bracket. If not, the unit may fall

and cause serious injury.

• Be sure to follow the operating instructions supplied

with your stand when installing the unit.

• Be sure to attach the brackets supplied with your

stand.

To prevent the unit from

falling

Place the display unit on a secure,

stable stand. Do not hang anything

on the display unit. The unit may

fall from the stand or wall-

hanging rack unit, causing damage or serious injury.

Do not allow children to climb on to the display unit.

7

Safety Information

GB

Power Sources

Overloading

This set is designed to

operate on a 220-240V AC

supply only. Take care not to

connect too many appliances

to the same mains socket as

this could result in fire or

electric shock.

Mains lead

protection

Pull out the mains lead

by the plug. Do not

pull on the mains lead

itself.

Mains

Do not use a poor fitting mains socket.

Insert the plug fully into the mains. If it is

loose, it may cause arcing and result in

fire. Contact your electrician to have the

mains socket changed.

Wiring

Unplug the mains lead when wiring cables. Be sure

to unplug the mains lead for your safety, when

hooking up.

Moisture

Do not touch the mains lead with a wet

hand. If you plug/unplug the mains lead

with a wet hand, it may cause electric

shock.

Cleaning

Clean the mains plug regularly. If

the plug is covered with dust and

it picks up moisture, its insulation

may deteriorate and result in fire.

Unplug the mains plug and clean

it regularly.

Lightning storms

For your own safety, do not

touch any part of the set, mains

lead or aerial lead during

lightning storms.

(continued)

8

Safety Information

Use

Damage requiring service

If the surface of the display unit cracks, do not touch it

until you have unplugged the mains lead. Otherwise

electric shock may result.

Ventilation holes

Do not insert anything in the

ventilation holes. If metal or

something flammable enters, it

may result in fire or electric

shock.

Servicing

Do not open the cabinet or

remove the rear cover of the

set. Refer to qualified

service personnel only.

Moisture and flammable

objects

• Do not let this unit get

wet. Never spill liquid of

any kind on the unit. If

any liquid or solid object

does fall through, do not operate the unit. It may

result in electric shock or damage to the unit.

Have it checked immediately by qualified

personnel.

• To prevent fire, keep inflammable objects or

naked lights (e.g. candles) away from the set.

For the media receiver unit

Object placement

Do not place anything heavy on

the media receiver unit. It may

damage the unit.

Liquid

Do not place objects containing

liquid on the media receiver

unit. It may result in electric

shock or damage the unit.

9

Safety Information

GB

Additional Safety Information

Electric shock

Do not touch the unit with wet hands. Doing so may cause

electric shock or damage the unit.

Broken glass

Do not throw anything at the

unit. The screen glass may

explode by the impact and

cause serious injury.

Protruding location

Do not install the display unit in protruding locations. If

you install the unit in the following locations, it may

result in injury.

• Do not install the unit in a location where the unit

protrudes, such as on or behind pillar.

• Do not install the unit in a location where you might

bump your head on it.

Oils

Do not install this unit in restaurants that use oil.

Dust absorbing oil may enter into the unit and

damage the unit.

Placement

Never place the set in hot, humid

or excessively dusty places. Do

not install the unit where it may

be exposed to mechanical

vibration.

Corrosion

If you use this set near the seashore, salt may corrode

metal parts of the unit and cause internal damage or

fire. It may also shorten the life of the unit. Steps

should be taken to reduce the humidity and

temperature of the area where the set is located.

Accessories

Secure the display unit properly.

If the display unit is not secured properly, it may fall and

cause injury. Take measures to prevent this by using a

stand or other apparatus on the floor or wall in the

specified manner, referring to the operating instructions

supplied with your stand.

Recommended place for

the media receiver unit

Place the media receiver unit

on a stable, level surface.

Otherwise, the media receiver

unit may fall and cause injury.

Use an optional Sony stand, which has adequate

strength.

Weight

Do not stand on the media receiver unit.

The unit may fall or be broken, causing

injury. Pay special attention when little

children are likely to come near the set.

Cleaning

Unplug the mains lead when cleaning this unit. If

not, it may result in electric shock.

Disposal of the display unit

• Do not dispose of display units with general

household waste.

• The LCD contains a small amount of liquid crystal

and mercury. The fluorescent tube used in this display

also contains mercury. Follow your local ordinances

and regulations for disposal.

(continued)

10

Safety Information

LCD Screen

• Although the LCD screen is made with high-precision

technology and has effective pixels of 99.99% or

more, black dots may appear or bright points of light

(red, blue, or green) may appear constantly on the

LCD screen. This is a structural property of the LCD

panel and is not a malfunction.

• Do not expose the LCD screen surface to the sun.

Doing so may damage the screen surface.

• Do not push or scratch the front filter, or place objects

on top of this unit. The image may be uneven or the

LCD panel may be damaged.

• If this unit is used in a cold place, a smear may occur

in the picture or the picture may become dark.

This does not indicate a failure. These phenomena

improve as the temperature rises.

• Ghosting may occur when still pictures are displayed

continuously. It may disappear after a few moments.

• The screen and cabinet get warm when this unit is in

use. This is not a malfunction.

Mains lead and

display cable

If you damage the mains

lead or display cable, it

may result in fire or

electric shock.

• Do not pinch, bend, or

twist the cable

excessively. The core

lines may be bared or

cut, causing a short -

circuit which may in

fire or electric shock.

• Do not convert or damage the mains lead or

display cable.

• Do not put anything heavy on the mains lead or

display cable. Do not pull the mains lead or

display cable.

• Keep the mains lead or display cable away from

heat sources.

• Be sure to grasp the plug when disconnecting the

mains lead.

Refer to the operating instructions when

disconnecting the display cable. If the mains lead or

display cable is damaged, stop using it and ask your

dealer or Sony service centre to exchange it.

Fluorescent lamp

This unit uses a special fluorescent lamp as its light

source. If the screen image becomes dark, flickers, or

does not appear, the fluorescent lamp has run down and

should be replaced. For replacement, consult qualified

service personnel.

When not in use

For environmental

and safety reasons, it

is recommended that

the set is switched off

when not in use - not

left in standby mode.

Disconnect from the mains.

Cleaning the screen surface

The screen surface is finished with a special coating to

prevent strong light reflections. Be sure to observe the

following precautions to avoid damaging the finish.

• To remove dust from the screen surface, wipe gently

with a soft cloth. If dust is persistent, wipe with a soft

cloth slightly moistened with a diluted mild detergent

solution. You can wash and repeatedly use the soft

cloth.

• Never use any type of abrasive pad, alkaline/acid

cleaner, scouring powder or strong solvent such as

alcohol, benzene or thinner.

Cable wiring

Take care not to catch your feet on the cables. It may

damage the unit.

Installation

Do not install optional components too close to the

display unit. Keep optional components at least 30

cm away from the display unit. If a VCR is installed

in front or at the right side of the display unit, the

picture may distort.

Cooling fan

This display unit uses a cooling fan to avoid overheating.

Note that the noise of the cooling fan may be heard from

the display unit, depending on where the display unit is

installed.

Heat

Do not touch the surface of the display unit. It

remains hot, even after the display unit has been

turned off for some time.

11

Safety Information

GB

Precautions

On viewing the TV comfortably

• To view the TV comfortably, the recommended viewing position is from four to seven times of the

screen’s vertical length away from the TV set.

• View the TV in a moderate light room, as viewing the TV in poor light taxes your eyes. Watching the

screen continuously for long periods of time can also tax your eyes.

On installing the TV set

Installing the display unit

Use the specified wall-mount bracket or stands.

Installing the media receiver unit

Leave enough space for ventilation between the exhaust fan in the rear of unit and the wall.

• Do not install the display unit in places subject to extreme temperature, for example in direct sunlight,

or near a radiator, or heating vent. If the unit is exposed to extreme temperature, the unit may heat up

and it may cause deformations of the casing or cause the unit to malfunction.

• After transporting the display unit directly from a cold to a warm location, or if the room temperature

has changed suddenly, pictures may be blurred or show poor colour over portions of the picture. This

is because moisture has condensed on the mirrors or lenses inside the unit. In this case let the moisture

evaporate before using the unit.

• To obtain a clear picture, do not expose the screen to direct illumination or direct sunlight. If possible,

use spot lighting directed down from the ceiling.

• The TV set is not disconnected from the mains when the switch is in Off position. To disconnect the

set completely, pull the plug from the mains.

On volume adjustment

• Adjust the volume so as not to trouble neighbours. Sound carries very easily at night time. Therefore,

closing the windows or using headphones is suggested.

• When using headphones, adjust the volume so as to avoid excessive levels, as hearing damage may

result.

On image

With extensive use of this TV set in 4:3 mode, the 4:3 screen area might become darker within a 16:9

panel. To avoid this problem, the “Smart” picture mode should be used.

On handling the remote control

• Handle the remote control with care. Do not drop or step on it, or spill liquid of any kind onto it.

• Do not place the remote control in a location near a heat source, or in a place subject to direct sunlight,

or in a damp room.

On handling and cleaning the screen surface of the display unit

To avoid screen degradation, follow the points mentioned below. Do not push on or scratch with hard

objects, or throw anything at the screen. The screen may be damaged.

• Be sure to unplug the mains lead connected to the media receiver unit from the mains before cleaning.

• Do not touch the display panel after operating continuously for a long period as the display panel

becomes hot.

• We recommend that the screen surface is touched as little as possible.

• Clean the screen with a soft cloth.

• Never use any type of abrasive pad, scouring powder, or solvent, such as alcohol or benzine. This type

of contact may result in damage to the screen surface.

(continued)

12

Safety Information

On cleaning the cabinet

• Be sure to unplug the mains lead connected to the media receiver unit from the mains before cleaning.

• Clean the cabinet with a soft cloth.

• Note that material deterioration or screen coating degradation may occur if the display unit is exposed

to a volatile solvent, such as alcohol, thinner, benzine or insecticide, or if prolonged contact is

maintained with rubber or vinyl materials.

• The ventilation holes can accumulate dust over a period of time and the accumulated dust may make

the cooling function of the built-in fan less effective. To prevent this, we recommend removing the dust

periodically (once a month) using a vacuum cleaner.

13

Safety Information

GB

Checking the Accessories Supplied

One Remote Control

(RM-972):

Two size AAA batteries

(R03 Type):

One Display Interface

Cable:

One Coaxial Cable: One AV Mouse:

Two Mains Leads

(Type C-4):

Use these mains leads

(with safety earth) if you

use the set outside the

United Kingdom.

Two Mains Leads

(Type BF):

• Use these mains leads

(with safety earth) if you

use the set in the United

Kingdom.

• See “NOTICE FOR

CUSTOMERS IN THE

UNITED KINGDOM” on

page 2 when using the

mains leads.

• These mains leads may not

be supplied depending on

the country.

Two Mains Leads

(Type C-5):

• Use these mains leads

(with safety earth) if you

use the set in the Swiss

Confederation.

• These mains leads may

not be supplied depending

on the country.

Do not remove ferrite cores.

14

Overview

Overview of the Display Unit

About the indicators

The following indicators are on the display unit and the media receiver unit.

POWER/STANDBY indicator

Lights up in green when the TV is switched on. When in standby mode, the indicator lights up in red.

When in PC power saving* mode, the indicator lights up in yellow.

TIMER indicator

When lit, indicates that one of the timers is set. When the on timer is set and the TV is in standby mode,

this indicator lights up in yellow. When one of the off timers is set, this indicator lights up in red. For more

details regarding the timers, refer to “ Timer” on page 40.

PICTURE OFF indicator

Lights up in blue when you press (picture off) on the remote control to switch off the picture. Only

the picture is switched off (the sound remains unchanged).

* If the TV is connected to a personal computer or video graphic board that is DPMS (Display Power

Management System) compliant, the TV will automatically reduce power consumption (PC power

saving mode).

If you connect a personal computer to the PC connector, the “Auto Shutoff ” function cannot

work. After a certain period without a signal from a personal computer, the TV switches into PC

power saving mode, not standby mode.

POWER/STANDBYTIMERPICTURE OFF

POWER/STANDBY indicator

TIMER indicator

PICTURE OFF indicator

Remote control sensor

15

Overview

GB

Overview of the Media Receiver Unit Buttons and

Indicators

654321

66

6

PC

MEMORY STICK

PROG

MENU

PC

OK

L/G/S/I R/D/D/D

MENU OK

PROG

64321

PC

MEMORY STICK

5

(Power on/standby) indicator

(Power) switch

(Timer) indicator

“Memory Stick” slot

“Memory Stick”

access lamp

PROG (channel)

+/– buttons

2(Volume) +/–

buttons

(Input

select) button

(TV mode)

button

Input select indicators

To watch the picture of connected

equipment, press repeatedly until the

correct input indicator lights up. For more

details, refer to “Using Optional

Equipment” on page 63.

TV indicator

1 Input 1 indicator

2 Input 2 indicator

3 Input 3 indicator

4 Input 4 indicator

5 Input 5 indicator

6 Input 6 indicator

PC PC indicator

MEMORY

Memory Stick indicator

STICK

Menu button

///

buttons

OK button

Front connectors*

* For more details of the front

connectors, refer to “Connecting

Optional Equipment” on page 59.

16

Overview

Overview of the Remote Control Buttons

Buttons

Description

a To Temporarily

Switch Off TV:

Press this button to temporarily switch off the TV

(the (power on/standby) indicators on the

display unit and the media receiver unit light up in

red). Press again to switch on the TV from standby

mode.

To save energy we recommend switching the TV

off completely when the TV is not in use.

After a certain period without a signal and

without any button being pressed, the TV

automatically switches into standby mode

(Auto Shutoff, page 41).

b VCR or DVD on/

off:

Press this button to switch your VCR or DVD on

or off.

c Selecting input

source:

Press this button repeatedly until the desired input

symbol of the source appears on the TV screen.

d Displaying the

Memory Stick

Home (“Memory

Stick” picture

viewer):

Press this button to display the Memory Stick

Home (“Memory Stick” picture viewer). For more

details, refer to “Using the Memory Stick Home”

on page 50.

e Selecting

channels:

Press this button to select channels.

For double-digit programme numbers, enter the

second digit within 2.5 seconds.

Buttons

Description

f a) If the Media Selector is

switched to TV:

Press this button to watch the last channel selected (the last channel

watched for at least 5 seconds).

b) If the Media Selector is

switched to VCR:

For Sony’s VCR double-digit programme numbers, e.g. 23, press

-/- - first and then the buttons 2 and 3.

g a) If the Media Selector is

switched to VCR or DVD:

Press this button to record programmes.

b) If the Media Selector is

switched to TV:

Press this button to return the picture and sound to the factory preset levels.

This will also return the set to the install condition.

h Switching off the picture: Press this button to switch off the picture. Only the picture is switched off;

the sound remains on. Press again to cancel.

i Displaying the clock: Press this button to display the clock on the TV screen. Press again to turns

the clock display off.

The clock display turns off automatically 5 minutes after it is

turned on.

j This button works in Teletext mode and is also used for programming the remote control to operate

the VCR and DVD.

OK

PROG

MENU

TV

VIDEO

17

Overview

GB

Buttons

Description

k Selecting screen format: Press this button repeatedly to change the format of the screen. For more

details, refer to “Screen Control” on page 30.

l Selecting channels: Press these buttons to select the next or previous channel.

m Displaying the menu

system:

Press this button to display the menu on the TV screen. Press again to

remove the menu display from the TV screen.

n Adjusting the TV volume: Press these buttons to adjust the volume of the TV.

o Selecting Sound effect: Press this button repeatedly to change the sound effect.

p Selecting Picture mode: Press this button repeatedly to change the picture mode.

q Joystick

a) If the Media Selector is

set to TV:

• When MENU is selected, use these buttons to operate the menu system.

For more details, refer to “Introducing and Using the Menu System” on

page 26.

• When MENU is switched off, press OK to show an overview of all TV

channels. Then press

or to select the channel and then press

to watch the selected channel.

b) If the Media Selector is

set to VCR or DVD:

Using these buttons, you can control the main functions of your VCR or

DVD.

r NexTView: For more details, refer to “NexTView*” on page 56.

s Selecting Teletext: Press this button to switch on Teletext.

t Media Selector: With this remote control you can operate not only this TV but also the main

functions of your VCR or DVD.

Switch on the equipment you want to operate and then press this button

repeatedly to select VCR, TV or DVD. A green light will light up

momentarily.

An initial set up is required to synchronise this remote control to

your VCR or DVD. This setup depends on the manufacturer. For

more details, refer to “Remote Control Configuration for VCR/

DVD” on page 64.

u Displaying On Screen

information:

Press this button to display all on-screen indications. Press again to cancel.

v Selecting TV mode: Press this button to switch off teletext or video input.

w Muting the Sound: Press this button to mute the TV sound. Press again to restore the sound.

In addition to the TV functions, all coloured buttons as well as green symbols are also used for

Teletext operations. For more details, refer to “Teletext” on page 55.

18

Installation

Inserting Batteries into the Remote Control

Make sure you insert the supplied batteries observing the correct polarity.

Always remember to dispose of used batteries in an environmentally friendly way.

m

<

19

Installation

GB

Connecting the Display Unit to the Media Receiver

Unit

• Use the supplied display interface cable.

• Use the supplied mains lead for the display unit (Type C-4, Type BF or Type C-5, see page 13).

1 Connect the supplied display interface cable and the supplied mains lead for the display unit to the

display unit.

Do not connect to the mains before all connections are completed.

BLACK

DISPLAY SIGNAL IN

WHITEAC IN

Tighten the

screw slowly

until the screw

is stabilized.

Mains leads

(supplied)

After making all

connections,

connect to a wall

outlet.

Display interface

cable (supplied)

To Media receiver unit.

(continued)

20

Installation

2 Install the display unit using the specified wall-mount bracket or stand.

Before installing the display unit, check the installation instructions of your wall-mount bracket or

stand.

3 Connect the supplied display interface cable to the media receiver unit.

1/

R/D/D/D

55

L/G/S/I

Y

CTRL

S

CENTRE

SPEAKER IN

180W (6 ) MAX

P

B

/C

B

P

R

/C

R

(SMARTLINK)

AV

MOUSE

W/G/W/GL/G/S/IR/D/D/D

2/

3/

4/

DISPLAY SIGNAL OUT

BLACK WHITE

AC IN

La page est en cours de chargement...

Sony KLV-30MR1 Manuel utilisateur

Sony KLV-30MR1 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents