Hunter Fan 83702 Le manuel du propriétaire

Taper
Le manuel du propriétaire
42911-01 02/12/2008
1
83702 Sona Bath Ventilator With Light
READ and SAVE THESE INSTRUCTIONS
I n s t a l l a t i o n G u i d e
ENGLISH
See page 2
FRANçAIS
Consulter la page 21
009_42911_EngF_2-12-08.indd 1 2/12/08 3:12:53 PM
42911-01 02/12/2008
2
DISCONNECT ELECTRIC
POWER SUPPLY
AND LOCK OUT
SERVICE PANEL BEFORE
SERVICING UNIT
W A R N I N G
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS,
OBSERVE THE FOLLOWING:
1. For general ventilating use only. Do not use to exhaust hazard-
ous or explosive materials and vapors.
2. To avoid motor bearing damage and noisy/unbalanced impellers,
keep drywall spray, construction dust, etc. off power unit.
3. DO NOT install this product in a wall. This product is designed
for installation in ceilings up to a 12/12 pitch (45 degrees).
Ductwork must point upward.
4. Pleasereadspecicationlabelonproductforfurtherinformation
and requirements.
PREVENTATIVE MAINTENANCE
A clean fan provides better service. Disconnect the power supply and
clean the fan as listed below.
TO CLEAN GRILLE: Use a mild detergent, such as dishwashing
liquid, and a soft cloth. DO NOT use abrasive cloths, steel wool pads
or scouring powders.
TO CLEAN FAN ASSEMBLY: Unplug motor cord from receptacle.
To remove motor plate, find the single tab on the motor plate (located
next to the receptacle). Push up rear motor plate tab while pushing
out on the side of the housing or insert a screwdriver into the slot in
the housing (next to tab) and twist screwdriver. Gently vacuum fan,
motor and interior of housing.
METAL AND ELECTRICAL PARTS SHOULD NEVER BE IMMERSED
IN WATER.
MAINTENANCE
The motor is permanently lubricated and never needs oiling. If the
motor bearings are making excessive or unusual noises, replace the
motor with the exact service motor. You should replace the impeller at
the same time.
C A U T I O N
W A R N I N G
1. Use this unit only in a manner intended by the manufacturer.
If you have questions, contact the manufacturer.
2. Before servicing or cleaning the unit, switch power off at service
panel and lock the service disconnecting means to prevent
power from being switched on accidentally. When the service
disconnecting means cannot be locked, securely fasten a
prominent warning device, such as a tag, to the service panel.
3. Installation work and electrical wiring must be done by quali-
edperson(s)inaccordancewithallapplicablecodesand
standards,includingre-ratedconstruction.
4. Sufcientairisneededforpropercombustionandexhausting
ofgassesthroughtheue(chimney)offuelburningequipment
to prevent backdrafting. Follow the heating equipment manufac-
turer’s guideline and safety standards,such as those published
by the National Fire Prevention Association (NFPA), and the
American Society for Heating, Refrigeration and Air-Conditioning
Engineers (ASHRAE), and the local code authorities.
5. When cutting or drilling into wall(s) or ceiling, do not damage
electrical wiring or other hidden utilities.
6. Ducted fans must always be vented to the outdoors.
7. If this unit is to be installed over a tub or shower, it must be
marked as appropriate for the application and be connected to a
GFCI (Ground Fault Circuit Interrupter) – protected branch circuit.
8. Never place a switch where it can be reached from a tub or
shower.
9. Installfanatleast5feet(1.52m)abovetheoor.
10. This unit must be grounded.
11. Unit must not be installed in a ceiling thermally insulated to a
value greater than R40.
Do Not Install Above
Or Inside This Area
Cooking
Equipment
Floor
45° 45°
COOKING AREA
009_42911_EngF_2-12-08.indd 2 2/12/08 3:12:53 PM
42911-01 02/12/2008
3
E
F
G
H
I
J
M
N
O
x5
*
*
*
NOTE:
Strain relief cable connector
must be installed. Not Included.
A
B
C
95044-01-000
95022-01-000
75867-01-000
03242-07-133
95492-05-000
74508-03-133
96371-01-444
K
77520-01
L
65219
75184-01-133
96370-01-444
Extra Screws
x2
D
3/8” Cable Connector
x2
1
Check all the parts.
If damaged, call
1-888-830-1326
for replacements.
2
F
J
Turn off the power source.
Tools Needed. (Not supplied.)
Estimated assembly time: 30 to 60 minutes
Before Installation
Loosen screws.
NOTE: Remove all packing materials before installation.
Included
009_42911_EngF_2-12-08.indd 3 2/12/08 3:12:55 PM
42911-01 02/12/2008
4
5
4
7
H
8
G
3
I
F
6
Remove the motor/blower from the housing.
Remove the pre-loaded screw tip covers.
Remove the wiring cover screw.
Back out the pre-loaded screw tips until flush
with the side of the housing.
Remove the wiring cover.
Remove packing material.
009_42911_EngF_2-12-08.indd 4 2/12/08 3:12:58 PM
42911-01 02/12/2008
5
9
F
10
B
C
A11
F
5/8
1/2
5/8
1/2
A12
Pop out the first wiring access slug. Use second if needed. Insert the strain relief (not included) into the housing and
secure with washer.
Position the correct depth mark at the bottom edge of the
joist based on the thickness of your sheetrock.
Choose Installation Option
For New Construction - attaching to joist go to step A11, page 5
For New Construction - suspended between joists go to step B11, page 8
For Existing Construction - accessible from above go to step C11, page 11
For Existing Construction - accessible only from below go to step D11, page15
Screw pre-loaded screws into joist or framing.
New Construction - attaching to joist
009_42911_EngF_2-12-08.indd 5 2/12/08 3:13:01 PM
42911-01 02/12/2008
6
A
3 Pin
2 Pin
Fan Motor
Light
Light
Green
Black
Black
Red
Red
White
Black
Black
White
White
Bare Copper
Ground
A14
Night Light
Night Light
Switch 1 (AC In)
Main Switch 1 (AC In)
Switch 2 (AC In)
*Option Fan & Main Light Together
*Option
A13
0
A16
H
A15
F
Route wires through the strain relief. For supply connection,
use wires suitable for at least 90º C (194º F).
Connect wires as shown.
Connect 4” duct and vent to the outside. Tape joints.
If ducting does not fit securely, an adapter may need
to be purchased.
Install the wiring cover plate. Make sure all
wiring connections are inside the box or under
the wiring cover plate.
009_42911_EngF_2-12-08.indd 6 2/12/08 3:13:03 PM
42911-01 02/12/2008
7
A19
J
A20
0000
A17
0000
I
A18
ON
OFF
A21
A22
E1
Go to step
on page 17
to attach grille.
Secure the motor by tightening the 2 screws.
Turn on the power source.
Connect wiring harness. DO NOT ALLOW THE MOTOR TO
HANG FROM THE WIRING HARNESS.
Reinstall the motor by inserting the tabs and pushing up
into position. Make sure the wires are not pinched between
the motor and the housing.
Test the motor. If the motor does not run,
check the plug connection.
009_42911_EngF_2-12-08.indd 7 2/12/08 3:13:07 PM
42911-01 02/12/2008
8
Slide the mounting rails into brackets.
Mark position of screws by using holes as a template.
Insert screws, leaving space between the screw
head and the joist. Screws are not provided.
New Construction suspended between joists
B11
E
F
5/8
1/2
5/8
1/2
B12
1/8” bit
B14
B15
B16
F
B13
Position the correct depth mark at the bottom edge of
the joist based on the thickness of your sheetrock.
Drill a hole in the center of each outline.
Attach the rails onto the screws.
009_42911_EngF_2-12-08.indd 8 2/12/08 3:13:09 PM
42911-01 02/12/2008
9
Tighten screws. Route wires through the strain relief. For supply connection,
use wires suitable for at least 90º C (194º F).
Connect wires as shown.
B17
B18
B21
Install the wiring cover plate. Make sure all wiring
connections are inside the box or under the
wiring cover plate.
H
B20
G
Connect 4” duct and vent to the outside. Tape joints.
If ducting does not fit securely, an adapter may need
to be purchased.
009_42911_EngF_2-12-08.indd 9 2/12/08 3:13:13 PM
42911-01 02/12/2008
10
B27
E1
Go to step
on page 17
to attach grille.
B22
I
I
B23
B25
Turn on the power source.
Reinstall the motor by inserting the tabs and pushing up into
position. Make sure the wires are not pinched
between the motor and the housing.
ON
OFF
B26
Test the motor. If the motor does not run,
check the plug connection.
Connect wiring harness. DO NOT ALLOW THE MOTOR TO
HANG FROM THE WIRING HARNESS.
B24
J
Secure the motor by tightening the 2 screws.
009_42911_EngF_2-12-08.indd 10 2/12/08 3:13:17 PM
42911-01 02/12/2008
11
C12
E
F
Existing Construction accessible from above
EXISTING FAN
C11
NO EXISTING FAN
9”
9.75”
OR
Remove an existing fan and check to make sure the
opening is large enough to accommodate the new
motor housing (9”x 9.75”).
Cut out an opening for the housing.
Use the motor housing as a template to mark position.
Slide the mounting rails into brackets.
Position the correct depth mark at the bottom edge of the
joist based on the thickness of your sheetrock.
5/8
1/2
5/8
1/2
C13
C14
Mark position of screws by using holes as a template.
009_42911_EngF_2-12-08.indd 11 2/12/08 3:13:20 PM
42911-01 02/12/2008
12
C17
C18
C19
C20
C15
C16
Drill a hole in the center of each outline. Insert screws, leaving space between the screw head
and the joist. Screws are not provided.
Attach the rails onto the screws. Tighten screws.
Connect 4” duct and vent to the outside. Tape joints.
If ducting does not fit securely, an adapter may
need to be purchased.
Route wires through the strain relief. For supply connection,
use wires suitable for at least 90º C (194º F).
009_42911_EngF_2-12-08.indd 12 2/12/08 3:13:23 PM
42911-01 02/12/2008
13
C21
A
3 Pin
2 Pin
Fan Motor
Light
Light
Green
Black
Black
Red
Red
White
Black
Black
White
White
Bare Copper
Ground
C22
Night Light
Night Light
Switch 1 (AC In)
Main Switch 1 (AC In)
Switch 2 (AC In)
*Option Fan & Main Light Together
*Option
Tighten the strain relief screws.
Connect wires as shown.
C24
I
H
C23
G
Install the wiring cover plate. Make sure all wiring
connections are inside the box or under the
wiring cover plate.
Connect wiring harness. DO NOT ALLOW THE MOTOR TO
HANG FROM THE WIRING HARNESS.
009_42911_EngF_2-12-08.indd 13 2/12/08 3:13:26 PM
42911-01 02/12/2008
14
C25
I
C26
J
C27
ON
OFF
C28
Secure the motor by tightening the 2 screws.
Turn on the power source. Test the motor. If the motor does not run,
check the plug connection.
C29
E1
Go to step
on page 17
to attach grille.
Reinstall the motor by inserting the tabs and pushing up into
position. Make sure the wires are not pinched
between the motor and the housing.
009_42911_EngF_2-12-08.indd 14 2/12/08 3:13:29 PM
42911-01 02/12/2008
15
EXISTING FAN
D11
F
D12
Existing Construction accessible only from below
D13
2
1
D14
Route wires through strain relieif. For supply connection, use
wires suitable for at least 90º C (194º F).
Remove an existing fan and check to make sure the
opening is large enough to accommodate the new motor
housing (9”x 9.75”).
Move the housing into position above the ceiling.
Attach existing ducting to duct connector. Tape joints.
If ducting does not fit securely,
an adapter may need to be purchased.
F
D15
Screw pre-loaded screws into joist or framing.
009_42911_EngF_2-12-08.indd 15 2/12/08 3:13:31 PM
42911-01 02/12/2008
16
A
3 Pin
2 Pin
Fan Motor
Light
Light
Green
Black
Black
Red
Red
White
Black
Black
White
White
Bare Copper
Ground
D16
Night Light
Night Light
Switch 1 (AC In)
Main Switch 1 (AC In)
Switch 2 (AC In)
*Option Fan & Main Light Together
*Option
I
D18
I
D19
D20
J
Connect wires as shown.
Reinstall the motor by inserting the tabs and pushing up into
position. Make sure the wires are not pinched between the
motor and the housing.
Connect wiring harness. DO NOT ALLOW THE MOTOR TO
HANG FROM THE WIRING HARNESS.
Secure the motor by tightening the 2 screws.
H
D17
G
Install the wiring cover plate. Make sure all wiring
connections are inside the box or under
the wiring cover plate.
009_42911_EngF_2-12-08.indd 16 2/12/08 3:13:35 PM
42911-01 02/12/2008
17
ON
OFF
D22
D23
E1
Go to step
on page 17
to attach grille.
D21
Test the motor. If the motor does not run,
check the plug connection.
Turn on the power source.
Attaching the Grille
Remove the thumbscrews. Connect wiring harness. DO NOT ALLOW THE FIXTURE TO
HANG FROM THE WIRING HARNESS.
N
F
E1
E2
M
009_42911_EngF_2-12-08.indd 17 2/12/08 3:13:38 PM
42911-01 02/12/2008
18
Position the strain relief bracket between the plugs as
shown, and screw into place.
E3
K
Align tabs on glass dome assembly with slots on light fixture
and insert tabs into slots.
Install 2 Max 60 watt A-15 bulbs (Not Included).
E8
Turn glass dome assembly as shown until it
locks into position.
E6
O
E7
Attach thumbscrews.
WARNING: To reduce the risk of electrical shock,
all 4 thumbscrews MUST be properly installed.
N
E5
Align posts A, B, C and D (stamped into motor housing)
with posts A, B, C and D (stamped into light fixture).
Slide light fixture over posts.
M
E4
009_42911_EngF_2-12-08.indd 18 2/12/08 3:13:39 PM
42911-01 02/12/2008
19
Trouble Shooting
Problem: Fan does not come on.
Solution:
 •HunterFanBathVentilatorsareextremelyquiet.Toconrmthatthefanisrunning,placeyourhandneartheventstofeel
the air movement.
• Turn power on, replace fuse, or reset breaker.
• Check all plug connections to be sure they are secure.
• Check the wiring to make sure it matches the wiring diagram.
Problem: Light does not come on.
Solution:
Replace the light bulb with a new bulb.
Turn power on, replace fuse, or reset breaker.
Check all plug connections to be sure they are secure.
Check the wiring to make sure it matches the wiring diagram.
Problem: Fan is noisy.
Solution:
Check and tighten all fasteners.
Check the glass to make sure it is secure.
 •Checktheappertomakesureitmovesfreely.
If you need parts or service assistance, please call 888-830-1326 or visit us at our WEB site at http://www.hunterfan.com.
009_42911_EngF_2-12-08.indd 19 2/12/08 3:13:40 PM
42911-01 02/12/2008
20
2500 Frisco Avenue, Memphis, Tennessee 38114
Printed in China
Warranty
Hunter Fan Company
Bath Exhaust Fan
LIMITED WARRANTY
Hunter Fan Company makes the following limited warranty to the original user or consumer purchaser of this Hunter bath exhaust fan:
IfanypartofyourHunterbathexhaustfan(exceptforglassxturesandlightbulbs)failsatanytimewithinoneyearafterthedateof
sale to you due to a defect in material or workmanship, we will repair or, at our option, replace the defective part free of charge for parts
and labor performed at our nearest service center or at our Service Department in Memphis, Tennessee. After this one-year period, you
will be responsible for all parts and labor costs for repairs on the bath exhaust fan except for motor repairs as provided below.
IfyourHunterbathexhaustfanmotorfailsatanytimewithinveyearsafterthedateofsaletoyouduetoadefectinmaterialorwork
-
manship, labor and materials to repair the defect will be provided free of charge at our nearest service center or our Service Department
in Memphis, Tennessee. If no replacement part can be provided, we will, at our option, either refund the actual purchase price of your
bathexhaustfanorprovideareplacementfreeofcharge.Afterthisve-yearperiod,youwillberesponsibleforallpartsandlaborcosts
for repairs on all parts of the bath exhaust fan.
IF THE ORIGINAL USER OR CONSUMER PURCHASER CEASES TO OWN THE FAN, THIS WARRANTY AND ANY IMPLIED
WARRANTY WHICH THEN REMAINS IN EFFECT, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTY OF MERCHANT-
ABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE VOIDED. NO WARRANTY, EXPRESS OR IMPLIED, INCLUDING ANY
WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, IS MADE IN RESPECT OF GLASS FIXTURES
OR LIGHT BULBS OR THE FINISH ON ANY METAL PORTION OF THE BATH EXHAUST FAN.
THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS WARRANTIES. THE DURATION OF ANY IMPLIED WARRANTY, INCLUD-
ING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, IN
RESPECT TO ANY HUNTER FAN BATH EXHAUST FAN MOTOR OR OTHER FAN PART, IS EXPRESSLY LIMITED TO THE PERIOD
OF THE EXPRESS WARRANTY SET FORTH ABOVE FOR SUCH MOTORS OR OTHER PARTS.
This warranty is voided if your Hunter bath exhaust fan is not purchased and installed in the U.S.A. This warranty excludes and does
not cover defects, malfunctions or failures of any Hunter bath exhaust fan which were caused by repairs by persons not authorized by
us,useofpartsoraccessoriesnotauthorizedbyus,mishandling,improperinstallation,modicationsordamagetotheHunterbath
exhaust fan while in your possession, or unreasonable use, including failure to provide reasonable and necessary maintenance.
To obtain servicing, contact the nearest Hunter authorized service center of the Hunter Fan Company Service Department, 2500 Frisco
Avenue, Memphis, Tennessee 38114. Please contact us before shipping your bath exhaust fan to us. If we authorize you to ship it to
us, you will be responsible for all insurance and freight or other transportation charges to our factory or service center. We will return
your Hunter bath exhaust fan freight prepaid. Your Hunter bath exhaust fan should be properly packed to avoid damage in transit since
we will not be responsible for any such damage. Proof of purchase is required when requesting warranty service. The purchaser must
present the sales receipt or other document that establishes proof of purchase.
IN NO EVENT SHALL HUNTER FAN COMPANY BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES.
SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR LIMITA-
TION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES SO THE ABOVE LIMITATION OR EXCLUSIONS MAY NOT APPLY TO
YOU.
THE WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE
TO STATE.
© 2008 Hunter Fan Company
009_42911_EngF_2-12-08.indd 20 2/12/08 3:13:40 PM
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40

Hunter Fan 83702 Le manuel du propriétaire

Taper
Le manuel du propriétaire

dans d''autres langues