VTech CS6649-2 Manuel utilisateur

Catégorie
Téléphones
Taper
Manuel utilisateur

Ce manuel convient également à

DECT 6.0 cordless telephone
User’s manual
Go to www.vtechphones.com
to register your product for
enhanced warranty support and
lastet VTech product news.
CS6648-2
CS6648-3
CS6649
CS6649-2
CS6649-3
BC
Congratulations
on purchasing your new VTech product.
Before using this telephone, please read
Important safety instructions.
This manual has all the feature operations
and troubleshooting necessary to install
and operate your new VTech telephone.
Please review this manual thoroughly to
ensure proper installation and operation
of this innovative and feature rich VTech
product.
For support, shopping, and everything
new at VTech, visit our website at
www.vtechphones.com. In Canada,
please visit www.vtechcanada.com.
Telephones identified with this
logo have reduced noise and
interference when used with
most T-coil equipped hearing
aids and cochlear implants.
The TIA-1083 Compliant
Logo is a trademark of the
Telecommunications Industry
Association. Used under
license.
The ENERGY STAR
®
program
(www.energystar.gov)
recognizes and encourages
the use of products that save
energy and help protect our
environment. We are proud
to mark this product with
the ENERGY STAR
®
label
indicating it meets the latest
energy efficiency guidelines.
T
Compatible with
Hearing Aid T-Coil
TIA-1083
i
Table of contents
What’s in the box ........................................ 1
Overview...................................................... 2
Telephone base overview .............................2
Handset overview ..........................................4
Charger overview ..........................................5
Display icons overview ..................................5
Handset and telephone base indicators .......6
Connect ....................................................... 6
Connect the telephone base .........................6
Mount the telephone base.............................6
Install and charge the battery ........................7
Before use ................................................... 8
Set date and time ..........................................8
Check for dial tone ........................................8
Operating range ............................................9
Congure your telephone .......................... 9
Using the telephone base/handset menu .....9
Set language .................................................9
Set date and time ........................................10
Home area code ..........................................10
Dial mode ....................................................10
Temporary tone dialing ................................10
Telephone operations .............................. 11
Make a call .................................................. 11
Predial a call ................................................11
Answer a call ...............................................12
End a call .....................................................12
Speakerphone .............................................12
Volume ........................................................12
Mute ............................................................12
Transfer a call ..............................................13
Join a call in progress .................................13
Call waiting ..................................................13
Chain dialing ................................................14
Find handset................................................14
Multiple handset use ................................ 15
Intercom ......................................................15
Answer an incoming call during an
intercom call .............................................16
Call transfer using intercom ........................16
Redial list................................................... 18
Review a redial list entry .............................18
Dial a redial list entry ...................................18
Delete a redial list entry ...............................18
Directory .................................................... 19
Add a directory entry ...................................19
Review a directory entry ..............................20
Alphabetical search .....................................20
Dial a directory entry ...................................20
Edit a directory entry ...................................20
Delete a directory entry ...............................21
Speed dial.................................................. 21
Assign a speed dial number ........................21
Reassign a speed dial number ...................21
Dial a speed dial number ............................22
Delete a speed dial number ........................22
Caller ID ..................................................... 23
Review a caller ID log entry ........................23
Missed call indicator ....................................23
View dialing options.....................................23
Dial a caller ID log entry ..............................24
Save a caller ID log entry to the directory ...24
Delete caller ID log entries ..........................24
Sound settings .......................................... 25
Key tone ......................................................25
Ringer tone ..................................................25
Telephone base ringer volume ....................26
Handset ringer volume ................................26
Temporary ringer silencing ..........................26
Quiet mode ..................................................26
About the built-in answering system and
voicemail service .................................. 27
Set your built-in answering system ........ 28
Turn the answering system on or off ...........28
Default announcement ................................29
Record your own announcement ................29
Play your announcement ............................29
Delete your announcement .........................30
Set number of rings .....................................30
Set recording time .......................................30
Turn the call screening on or off ..................30
Turn the message alert tone on or off .........31
ii
Using your built-in answering system .... 31
Message capacity .......................................31
New message indication .............................31
Message playback ......................................32
Delete all old messages ..............................32
Remote access ...........................................33
Set your remote access code .....................33
Call screening..............................................34
Call intercept ...............................................34
Temporarily turn off the message
alert tone ..................................................34
Record, play and delete memos .................34
Use the built-in answering system and
voicemail service .................................. 35
Retrieve voicemail from telephone
service .................................................... 35
Retrieve voicemail .......................................35
Voicemail number ........................................35
Turn off the new voicemail indicators ..........36
Register a handset ................................... 37
Replace a handset .................................... 38
Other information ..................................... 38
Website .......................................................38
Screen messages ..................................... 39
General product care ............................... 41
Frequently asked questions .................... 41
The RBRC
®
seal ........................................ 44
FCC, ACTA and IC regulations ................ 45
California Energy Commission battery
charging testing instructions ............... 47
For C-UL compliance only ....................... 48
Limited warranty ....................................... 51
Technical specications .......................... 53
1
Your telephone package contains the
following items. Save your sales receipt
and original packaging in case it is
necessary to ship your telephone for
warranty service.
NOTE
To purchase a replacement battery or power
adapter, visit our website at
www.vtechphones.com or call
1 (800) 595-9511. In Canada, go to
www.vtechcanada.com or call
1 (800) 267-7377.
1 set for CS6648-2/CS6648-3/
CS6649/CS6649-2/CS66493-3
1 set for CS6649;
2 sets for CS6648-2/CS6649-2;
3 sets for CS6648-3/CS6649-3
1 set for CS6648-2/CS6649-2;
2 sets for CS6648-3/CS66493-3
1 set for CS6648-2/CS6648-3/
CS6649/CS6649-2/CS66493-3
What’s in the box
Abridged
users
manual
Important
safety
instructions
2
Overview
Telephone base overview
1 – LCD display
2 – IN USE light
On when the phone is in use, or
when the answering system is
answering an incoming call.
On when a handset is being
registered.
Flashes when there is an incoming
call.
Flashes when handsets are being
deregistered.
Flashes when another telephone
on the same line is in use.
3 – FLASH
During a call, press to answer an
incoming call when you receive a
call waiting alert.
CANCEL
While in a menu, press to cancel
an operation, back up to the
previous menu or exit the menu
display.
Press and hold to erase the
missed call indicator when the
phone is not in use.
While the phone is ringing,
press to silence the base ringer
temporarily.
CID
Press to scroll down while in
menus and lists.
While entering or modifying names
or numbers, press to move the
cursor to the left.
Press to view the caller ID log
when the base is not in use.
Press to scroll up while in menus
and lists.
While entering or modifying names
or numbers, press to move the
cursor to the right.
Press to review the directory when
the base is not in use.
MENU/SELECT
Press to show a menu.
While in a menu, press to select
an item, or save an entry or
setting.
INT
Press to initiate or answer an
intercom call, or to transfer a call.
FIND HANDSET
Press to page all handsets when
the phone is not in use.
4 – /PLAY/STOP
Press to start or stop message
playback.
Flashes when there are new
messages or memos in the
answering system.
a
b
c
d
e
fgh
i
j
k
l
3
X/DELETE
Press to delete the playing
message or playing
announcement.
While reviewing the redial list,
directory or caller ID log, press to
delete an individual entry.
While entering names or numbers,
press to delete a character or digit.
/REPEAT
Press once to repeat the playing
message.
Press twice to play the previous
message.
/SKIP
Press to skip to the next message
during message playback.
5 – MUTE
During a call, press to mute the
microphone.
While the phone is ringing,
press to silence the base ringer
temporarily.
VOL
During a call or message
playback, press to adjust the
listening volume.
Press to adjust the telephone base
ringer volume when the base is
not in use.
/ANS ON/OFF
Press to turn the built-in answering
system on or off.
REDIAL/PAUSE
Press repeatedly to view the last
10 numbers dialed.
Press and hold to insert a dialing
pause while dialing or entering
numbers.
/SPEAKER
Press to make, answer or end a
call.
During a call, press to switch
between the corded handset and
the base speakerphone.
6 –
Press and hold to set and turn on
the quiet mode, or turn it off.
Press repeatedly to display other
dialing options when reviewing a
caller ID log entry.
7 –
Press to enter space during text
editing.
8 –
Press to switch to tone dialing
during a call if you have pulse
service.
9 – MIC
Microphone.
10 – 1
While reviewing a caller ID log
entry, press repeatedly to add or
remove 1 in front of the telephone
number before dialing or saving it
in the directory.
Press and hold to set or dial your
voicemail number.
11 – Speakerphone
12 – Corded handset
4
Handset overview
1 – Handset earpiece
2 – LCD display
3 –
Show the menu.
While in a menu, press to select
an item or save an entry or setting.
4 –
Hang up a call.
Return to the previous menu
or idle mode without making
changes.
Delete digits while predialing.
Silence the handset ringer
temporarily while the phone is
ringing.
Press and hold to erase the
missed call indicator when the
phone is not in use.
5 –
Press and hold to turn on quiet
mode, or turn it off.
Press repeatedly to display other
dialing options when reviewing a
caller ID log entry.
6 – INT
Press to initiate or answer an
intercom call, or to transfer a call.
7 – MUTE/DELETE
Mute the microphone during a call.
Silence the handset ringer
temporarily while the phone is
ringing.
Delete the displayed entry while
reviewing the directory, caller ID
log or redial list.
Delete digits or characters when
entering numbers or names.
Delete the playing message or
playing announcement.
8 – Microphone
9 –
Press to make or answer a call.
During a call, press to
switch between the handset
speakerphone and the handset
earpiece.
10 –
Press to switch to tone dialing
during a call if you have pulse
service.
11 –
While reviewing a caller ID log
entry, press repeatedly to add or
remove 1 in front of the telephone
number before dialing or saving it
in the directory.
Press and hold to set or dial your
voicemail number.
a
b
c
d
e
f
g
h
i
j
k
l
m
n
5
Charger overview
1 – Charging pole
Display icons overview
Handset display icons
The battery icon flashes when
the battery is low and needs
charging.
The battery icon animates
when the battery is charging.
The battery icon becomes
solid when the battery is fully
charged.
The handset ringer is off.
There are new voicemail
received from your telephone
service provider.
ANS ON
The answering system is
turned on.
ECO
The ECO mode activates
automatically to reduce
power consumption when the
handset is within range from
the telephone base.
NEW
The entry you are reviewing is
new in the caller ID log.
1/13
The number of current playing
message and the total number
of messages recorded.
Telephone base display icons
The telephone base ringer is off.
There are new voicemail received
from your telephone service
provider.
NEW
The entry you are reviewing is
new in the caller ID log.
13
MSG#
The total number of messages
recorded when the telephone
base is not in use.
The number of the playing
message.
12 –
Press to make or answer a call.
During a call, press to answer an
incoming call when you receive a
call waiting alert.
13 – REDIAL/PAUSE
Review the redial list.
Press and hold to insert a dialing
pause while dialing or entering
numbers.
14 – CHARGE light
On when the handset is charging
in the handset charger.
6
Connect
You can choose to connect the telephone
base for desktop usage or wall mounting.
NOTES
Use only the adapters provided.
Make sure the electrical outlets are not
controlled by wall switches.
The adapters are intended to be correctly
oriented in a vertical or floor mount
position. The prongs are not designed to
hold the plug in place if it is plugged into a
ceiling, under-the-table or cabinet outlet.
TIP
If you subscribe to digital subscriber line
(DSL) high-speed Internet service through
your telephone line, make sure you install
a DSL filter (not included) between the
telephone line cord and telephone wall
jack. Contact your DSL service provider for
more information.
Connect the telephone base
Mount the telephone base
Handset and telephone base
indicators
Handset lights overview
On when the handset
speakerphone is in use.
CHARGE
On when the handset is
charging in the handset
charger.
Telephone base lights overview
IN USE
On when the telephone
line is in use.
On when the answering
system is answering a
call.
On when you are
registering a handset.
Flashes quickly when
there is an incoming call.
Flashes when another
telephone sharing the
same line is in use.
Flashes when you are
deregistering all handsets.
/ANS
ON/OFF
On when the answering
system is turned on.
/
SPEAKER
On when the base
speakerphone is on.
/PLAY/
STOP
Flashes when there are new
memos or messages in the
answering system.
MUTE
On when mute function is on.
7
Connect the charger and charge
the battery
Place the handset in the telephone base
or handset charger to charge.
Once you have installed the battery,
the handset LCD display indicates the
battery status (see the table on next
page).
NOTES
For best performance, keep the handset
in the telephone base or charger when not
in use.
The battery is fully charged after 11 hours
of continuous charging.
If you place the handset in the telephone
base or the charger without plugging in
the battery, the screen displays
NO BATTERY.
Install and charge the battery
Install the battery
Install the battery as shown below.
NOTES
Use only supplied battery.
Charge the battery provided with this
product only in accordance with the
instructions and limitations specified in this
manual.
If the handset will not be used for a long
time, disconnect and remove the battery to
prevent possible leakage.
THIS SIDE UP
8
Battery
indicators
Battery
status
Action
The screen
is blank, or
displays Put
in charger
and flashes.
The battery
has no or
very little
charge. The
handset
cannot be
used.
Charge
without
interruption
(about 30
minutes).
The screen
displays
Low battery
and flashes.
The battery
has enough
charge to
be used
for a short
time.
Charge
without
interruption
(about 30
minutes).
The screen
displays
HANDSET X.
The battery
is charged.
To keep
the battery
charged,
place it in
the handset
charger when
not in use.
When the battery is fully charged, you can
expect the following performance:
Operation
Operating
time
While in handset use
(talking*)
Up to 7 hours
While in speakerphone
mode (talking*)
Up to 3.5 hours
While not in use
(standby**)
Up to 5 days
* Operating times vary depending on your
actual use and the age of the battery.
** Handset is not charging or in use.
Before use
After you install your telephone or power
returns following a power outage, the
handset will prompt you to set the date
and time.
Set date and time
NOTE
Make sure you set the date and time
including the year correctly; otherwise the
answering system does not announce the
correct day of the week for your recorded
messages time stamp.
Use the dialing keys (0-9) to enter
the month (MM), date (DD) and year
(YY). Then press SELECT.
Use the dialing keys (0-9) to enter
the hour (HH) and minute (MM).
Then press or to choose AM or
PM.
Press SELECT to save.
Check for dial tone
Press . If you hear a dial tone, the
installation is successful.
If you do not hear a dial tone:
Make sure the installation procedures
described above are properly done.
It may be a wiring problem. If you have
changed your telephone service to
digital service from a cable company
or a VoIP service provider, the
telephone line may need to be rewired
to allow all existing telephone jacks to
work. Contact your cable/VoIP service
provider for more information.
1.
2.
3.
9
Operating range
This cordless telephone operates with
the maximum power allowed by the
Federal Communications Commission
(FCC). Even so, this handset and
telephone base can communicate over
only a certain distance - which can vary
with the locations of the telephone base
and handset, the weather, and the layout
of your home or office.
When the handset is out of range, the
handset displays Out of range or no
pwr at base.
If there is a call while the handset is out
of range, it may not ring, or if it does ring,
the call may not connect well when you
press . Move closer to the telephone
base, then press to answer the call.
If the handset moves out of range during
a telephone conversation, there may be
interference. To improve reception, move
closer to the telephone base.
Configure your telephone
Using the telephone base/
handset menu
You can use the telephone base or
a cordless handset to change your
telephone settings.
Press MENU when the phone is not
in use.
Press or until the screen displays
the desired feature menu.
Press SELECT to enter that menu.
To return to the previous menu, press
CANCEL.
To return to idle mode, press and hold
CANCEL.
Set language
The LCD language is preset to English.
You can select English, French or
Spanish to be used in all screen
displays.
Press MENU when the handset/
telephone base is not in use.
Press or to scroll to Settings,
and then press SELECT twice.
Press or to choose English,
Français or Español, then press
SELECT.
4. Press SELECT twice to save your
setting. You hear a confirmation tone.
NOTE
If you accidentally change the LCD language
to French or Spanish, you can reset it to
English easily by pressing MENU then
entering 364
#
.
1.
2.
3.
1.
2.
3.
10
Set date and time
NOTE
Make sure you set the date and time
including the year correctly; otherwise the
answering system does not announce the
correct day of the week for your recorded
messages time stamp.
Press MENU when the handset/
telephone base is not in use.
Press or to scroll to Set date/
time, then press SELECT.
Use the dialing keys (0-9) to enter
the month (MM), date (DD) and year
(YY). Then press SELECT.
Use the dialing keys (0-9) to enter the
hour (HH) and minute (MM). Then
press or to choose AM or PM.
Press SELECT to save the settings.
You hear a confirmation tone.
Home area code
If you dial your local calls using only
seven digits (area code not required),
you can program your home area code
so that when you receive a call within
your local area, the telephone number
is automatically stored without the area
code in the caller ID log.
Press MENU when the handset/
telephone base is not in use.
Press or to scroll to Settings,
then press SELECT.
Press or to scroll to Home area
code, then press SELECT.
Use the dialing keys (0-9) to enter a
three-digit home area code.
Press DELETE on the handset to
delete a digit.
Press and hold DELETE on the
handset to delete all digits.
Press X/DELETE on the telephone
base to delete all digits.
1.
2.
3.
4.
5.
1.
2.
3.
4.
5. Press SELECT to confirm. You hear
a confirmation tone.
NOTE
If, in the future, your telephone service
provider requires you to dial the area code
when making a local call, or, if you move to
a location that requires it, follow the steps
above to delete the home area code you
have already programmed. After you have
deleted the home area code, _ _ _ will appear
on the screen.
Dial mode
The dial mode is preset to touch-tone
dialing. If you have pulse (rotary) service,
you must change the dial mode to pulse
dialing before using the telephone to
make a call.
Press MENU when the handset/
telephone base is not in use.
Press or to scroll to Settings,
then press SELECT.
Press or to choose Dial mode,
then press SELECT.
Press or to choose Touch-tone
or Pulse, then press SELECT to
save your selection. You hear a
confirmation tone.
Temporary tone dialing
If you have pulse (rotary) service only,
you can switch from pulse to tone dialing
temporarily during a call. This is useful if
you need to send touch-tone signals to
access your telephone banking or long
distance services.
During a call, press TONE .
Use the dialing keys to enter the
number you wish to dial. The
telephone sends touch-tone signals.
It automatically returns to pulse
dialing mode after you end the call.
1.
2.
3.
4.
1.
2.
11
Telephone operations
Telephone base control key panel:
Handset control key panel:
Make a call
Using a cordless handset:
Press
or .
When you hear a dial tone, dial the
number.
Using the telephone base:
Lift the corded handset, or press /
SPEAKER.
When you hear a dial tone, dial the
number.
NOTE
The screen displays the elapsed time as
you talk (in hours, minutes and seconds).
Predial a call
Using a cordless handset:
Enter the telephone number using
the dialing keys (0-9).
Press DELETE or CANCEL to
make corrections.
2. Press or to dial.
NOTE
While entering numbers, press and hold
PAUSE to insert a dialing pause (a P
appears).
Using the telephone base:
Enter the telephone number using
the dialing keys (0-9).
Press X/DELETE to make
corrections.
2. Lift the corded handset, or press
/SPEAKER to dial.
While entering numbers, press
and hold PAUSE to insert a dialing
pause (a P appears).
If you make a predial call while the
telephone line is in use, the screen
displays Unable to call.
1.
2.
1.
2.
1.
1.
12
Answer a call
Using a cordless handset:
Press , or any of the dialing
keys.
Using the telephone base:
Lift the corded handset, or press
/SPEAKER or any of the dialing
keys.
End a call
Using a cordless handset:
Press OFF or place the handset in the
handset charger.
Using the telephone base:
When you are using the corded
handset, place it on the telephone
base.
When you are using the base
speakerphone, press
/SPEAKER.
Speakerphone
Handset speakerphone:
When the cordless handset is on a call,
press
to switch between the handset
speakerphone and the handset earpiece.
When the speakerphone is active, the
handset displays Speaker and the
light
turns on.
Telephone base speakerphone:
When the corded handset is on a call,
press
/SPEAKER to switch between
the telephone base speakerphone and
the corded handset.
When the speakerphone is active, the
telephone base displays Speaker and
the /SPEAKER light turns on.
1.
2.
Volume
To adjust the listening volume on
a cordless handset:
During a call, press /VOLUME or
/VOLUME.
To adjust the listening volume at
the telephone base:
During a call, press VOL or VOL .
NOTES
The handset earpiece volume and
speakerphone volume settings are
independent.
When the volume reaches the minimum or
maximum setting, you hear two beeps.
Mute
The mute function allows you to hear the
other party but the other party cannot
hear you.
To mute a call on a cordless
handset:
During a call, press MUTE. The
handset displays Muted until the
mute function is turned off.
Press MUTE again to resume the
conversation. The handset displays
Microphone on briefly.
To mute a call at the telephone
base:
During a call, press MUTE. The
telephone base displays Muted and
the MUTE light turns on until the
mute function is turned off.
Press MUTE again to resume the
conversation. The telephone base
displays Microphone on briefly.
1.
2.
1.
2.
13
Join a call in progress
Another handset or the telephone base
can join you on an outside call. That
call continues until all parties hang up.
You can use the telephone base and
a cordless handset, or two cordless
handsets at a time on an outside call.
You can buy additional expansion
handsets (CS6609) for this telephone
base. You can register up to five
handsets to the telephone base.
To join a call with a cordless handset:
When a handset or the telephone
base is already on a call, press or
on another handset to join the call.
Press OFF or place the handset in the
handset charger to exit the call. The
call continues until both devices
hang up.
To join a call with the telephone base:
Lift the corded handset or press
/SPEAKER.
Place the corded handset back to the
telephone base or press
/SPEAKER
to exit the call. The call continues until
both devices hang up.
Call waiting
If you subscribe to call waiting service
from your telephone service provider,
you hear an alert tone when there is an
incoming call while you are already on a
call.
Press FLASH to put your current call
on hold and take the new call.
Press FLASH to switch back and forth
between calls.
If you also subscribe to caller ID
service, it will let you see the name and
telephone number of the caller during
call waiting.
Transfer a call
While on an outside call, you can
transfer the call from a cordless handset
to another handset or to the telephone
base.
During a call, press MENU.
Press or to scroll to Transfer,
then press SELECT.
Your handset shows Transfer to:
Press 7 for the telephone base or 1-5
for HANDSET 1 to HANDSET 5.
The outside call is put on hold and
your handset shows Calling HS X/
Calling base, and then Transferred.
The destination device rings and
shows Incoming call.
4. To answer the call on the destination
handset, press , or any of the
dialing keys.
-OR-
To answer the call on the telephone
base, lift the corded handset, or
press /SPEAKER or any of the
dialing keys.
NOTES
If the destination device does not answer
the call within 30 seconds, the call will be
reverted to the originating device. If the
originating device does not answer the
reverted call within 30 seconds, the
call ends.
If the destination device is in the directory
or caller ID log, or is out of range, the
originating device displays Unable to call
and then reconnects to the outside call.
1.
2.
3.
14
It may be necessary to change your
telephone service to use this feature.
Contact your telephone service provide if:
You have both caller ID and call
waiting, but as separate service (you
may need to combine these service);
You have only caller ID service, or
only call waiting service; or
You do not subscribe to caller ID or
call waiting services.
There are fees for caller ID services. In
addition, services may not be available in
all areas.
Chain dialing
Use this feature on the cordless
handsets to initiate a dialing sequence
from numbers stored in the directory,
caller ID log or redial list while you are on
a call.
Chain dialing can be useful if you wish
to access other numbers (such as bank
account numbers or access codes) from
the directory, caller ID log or redial list.
To access a number from the
directory while on a call:
Press MENU.
Press SELECT to choose
Directory.
Press or to scroll to the desired
entry.
Press SELECT to dial the displayed
number.
To access a number from the
caller ID log while on a call:
Press MENU.
Press or to scroll to Caller ID
log, then press SELECT.
Press or to scroll to the desired
entry.
Press SELECT to dial the displayed
number.
1.
2.
3.
4.
1.
2.
3.
4.
To access a number from the
redial list while on a call:
Press REDIAL to enter the redial list.
Press , or REDIAL repeatedly to
browse to the desired entry.
Press SELECT to dial the displayed
number.
NOTE
Press CANCEL to exit the directory, caller ID
log or redial list while on a call.
Find handset
This feature helps you find misplaced
handsets.
To start paging:
Press FIND HANDSET on the
telephone base and its screen
displays
**
Paging
**
. All idle handsets
ring and display
**
Paging
**
.
To stop paging:
Press , , OFF or any of the
dialing keys on the cordless handset.
-OR-
Place the cordless handset to the
handset charger.
-OR-
Press FIND HANDSET on the
telephone base.
NOTES
Press MUTE to turn off the ringer of
that handset temporarily. Paging tone
continues on all other idle handsets.
Do not press and hold FIND HANDSET
for more than four seconds. It may lead
to handset deregistration. If the handset
displays To register HS and See manual,
refer to the Add and register a handset
section to register the handset back to the
telephone base.
1.
2.
3.
15
Multiple handset use
Intercom
Use the intercom feature for
conversations between the telephone
base and a cordless handset, or two
cordless handsets.
When you have two or more handsets,
use the handset number to initiate an
intercom call or to transfer a call.
Press 7 for the telephone base or 1-5
for HANDSET 1 to HANDSET 5.
To initiate an intercom call with a
cordless handset:
Press INT on the cordless handset
when it is not in use.
If you have only one handset, the
telephone base shows Calling
base. The telephone base rings
and shows HS 1 is calling.
If you have two or more handsets,
your handset shows Intercom
to. Use the dialing keys to enter
a device number. Your handset
shows Calling HS X/Calling base.
The destination device rings and
shows HS X is calling.
2. To answer the intercom call on the
destination handset, press , INT,
or any of the dialing keys. Both
handsets now show Intercom.
-OR-
To answer the intercom call at the
telephone base, press /SPEAKER,
INT, any of the dialing keys, or lift the
corded handset. Both devices now
show Intercom.
3. To end the intercom call on either
handset, one party presses OFF,
or places the handset back in the
handset charger. Both handsets
display Intercom ended.
1.
-OR-
To end the intercom call at the
telephone base, press INT or
/SPEAKER when using the base
speakerphone, or place the corded
handset back to the telephone base.
Both screens display Intercom
ended.
NOTES
You can cancel the intercom call before it
is answered by pressing CANCEL or INT.
If the destination handset is not powered,
out of range, on a call, or does not answer
the intercom call within 100 seconds, your
handset displays Unable to call and then
returns to idle mode.
If the telephone base is on a call, or does
not answer the intercom call within 100
seconds, your handset displays Unable to
call and then returns to idle mode.
You can press OFF or MUTE on the
cordless handset, or CANCEL or MUTE
on the telephone base to temporarily
silence the intercom ringer.
Two intercom calls can be established at
a time.
To initiate an intercom call at the
telephone base:
Press INT on the telephone base
when it is not in use.
If you have only one handset, the
telephone base shows Calling HS
1. The handset rings and shows
Base is calling.
If you have two or more handsets,
the telephone base shows
Intercom to. Use the dialing keys
to enter a handset number. The
telephone base shows Calling HS
X. The destination handset rings
and shows Base is calling.
2. To answer the intercom call on the
destination handset, press
, INT,
or any of the dialing keys. Both
devices now show Intercom.
1.
16
pressress
/SPEAKER, or lift up the
corded handset to answer the call.
To end the intercom call without
answering or canceling the incoming
call, press /SPEAKER, or place the
corded handset back to the base. The. The
telephone continues to ring.
Call transfer using intercom
Use the intercom feature to transfer an
outside call to another cordless handset
or the telephone base.
To transfer a call with a cordless
handset:
During a call, press INT.
If you have only one handset, the
outside call is put on hold and your
handset shows Calling base. The
telephone base rings and shows
HS 1 is calling.
If you have two or more handsets,
your handset shows Intercom to.
Use the dialing keys to eenter a
device number. The outside call
is put on hold and your handset
shows Calling HS X/Calling base.
The destination device rings and
shows HS X is calling.
2. To answer the call on the destination
handset, press, press
, INT,
, or any
of the dialing keys. The outside call
is still on hold and both handsets
display Intercom. You can now have
a private intercom conversation.
-OR-
To answer the call at the telephone
base, press INT
,
/SPEAKER, any
of the dialing keys or lift the corded
handset. The outside call is still
on hold and both devices display
Intercom. You can now have a
private intercom conversation.
1.
3. To end the intercom call at the
telephone base, press INT, or
/SPEAKER when using the base
speakerphone, or place the corded
handset back to the telephone base.
Both screens display Intercom
ended.
-OR-
To end the intercom call on the
destination handset, press OFF,
or place the handset back in the
handset charger. Both screens
display Intercom ended.
NOTES
If you do not have any cordless handset
registered to the telephone base, you will
hear two beeps when you press INT on
the base.
You can cancel the intercom call before it
is answered by pressing CANCEL or INT.
If the destination handset is not powered,
out of range, on a call, or does not answer
the intercom call within 100 seconds, your
telephone base displays Unable to call
and then returns to idle mode.
Answer an incoming call during
an intercom call
If you receive an incoming outside call
during an intercom call, you will hear an
alert tone.
To answer on a cordless handset:
To answer the call, press
. The
intercom call ends automatically.
To end the intercom call without
answering or canceling the incoming
call, press OFF. The telephone
continues to ring.
To answer at the telephone base:
Press
/SPEAKER, or place the
corded handset back to the base. The
intercom call ends automatically. Then
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58

VTech CS6649-2 Manuel utilisateur

Catégorie
Téléphones
Taper
Manuel utilisateur
Ce manuel convient également à

dans d''autres langues