AT&T AWX22104 Guide de démarrage rapide

Quick start guide

AWX22104

DECT 6.0 cordless telephone/

answering system with

caller ID/call waiting

Instructions

This quick start guide provides you with basic installation and operation instructions.

A limited set of features are described in abbreviated form.

Please refer to the complete online AWX22104 DECT 6.0 cordless telephone/

answering system with caller ID/call waiting user’s manual for a full set of installation

and operation instructions at

http://telephones.att.com/manuals.

Before using this AT&T product, please read Important safety information on

pages 26-28 of this quick start guide.

Table of contents

Parts checklist........................................................1

Installation ...............................................................2

Battery installation ..............................................3

Battery charging ...................................................4

Handset overview .................................................5

Telephone base overview.................................6

Menu overview.......................................................7

Feature summary ..................................................7

Telephone settings ..............................................8

Making, answering and ending calls...........9

Options while on calls ....................................10

Handset locator ..................................................11

Intercom .................................................................12

Directory ................................................................14

Speed dial ............................................................15

Caller ID .................................................................16

Answering system and voicemail ..............17

Turn the answering system on or off ...... 17

Announcement ...................................................17

Number of rings .................................................18

Call screening .....................................................18

Message playback .............................................19

Delete all old messages ................................19

Remote access ....................................................19

Adding and registering handsets ..............20

Deregistering handsets ..................................21

Troubleshooting .................................................22

Important safety information ......................26

For C-UL compliance .......................................29

FCC Part 68 and ACTA....................................32

FCC Part 15 ..........................................................33

Limited warranty ................................................34

Technical specifications .................................36

Parts checklist

Your telephone package contains the following items. Save your sales receipt and

original packaging in the event warranty service is necessary.

1

Cordless handset Wall-mount bracket

Battery compartment cover

Telephone line cord

Battery for cordless handset

Power adapter for

telephone base

Telephone base

Quick start guide

AWX22104

DECT 6.0 cordless telephone/

answering system with

caller ID/call waiting

THIS SIDE UP / CE CÔTÉ VERS LE HAUT

Battery Pack / Bloc-piles :

BT162342/BT262342 (2.4V 3 00mAh Ni-MH)

WARNING / AVERTISSEMENT :

DO NOT BURN OR PUNCTURE BATTERIES.

NE PAS INCINÉRER OU PERCER LES PILES.

Made in China / Fabriqué en chine CR1423

2

Installation

Install the telephone base, as shown below. If you subscribe to high-speed Internet

service (DSL - digital subscriber line) through your telephone line, you must install a DSL

filter on the DSL line. If you want to mount your telephone on a wall, use the included

wall-mount bracket and refer to Wall-mount installation in the online user’s manual

for details.

IMPORTANT INFORMATION:

Use only the power adapter(s) provided with this product. To obtain a replacement, visit our website

at www.telephones.att.com or call 1 (800) 222-3111. In Canada, dial

1 (866) 288-4268.

Plug the large end

of the base power

adapter into an

electrical outlet not

controlled by a wall

switch.

Plug the small end

of the base power

adapter into the

power jack on

the bottom of the

telephone base.

Plug one end of the

telephone line cord into

a telephone wall jack.

A DSL filter (not

included) is required if

you have DSL high-speed

Internet service.

Route the cords

through the slots.

Plug the other end of

the telephone line cord

into the telephone line

jack on the bottom of

the telephone base.

3

T

H

IS

SI

D

E

U

P

/

CE

C

ÔT

É

V

ER

S

L

E HA

U

T

B

attery

P

ac

k

/

Bl

oc

-

p

i

l

e

s

:

B

T

1

62

3

42

/

B

T

2

6

2

34

2

(2

.

4V

3

00

m

Ah

N

i

-M

H)

W

ARN

I

N

G

/

A

V

E

RT

I

S

E

M

E

N

T

:

D

O

NOT

BU

R

N

OR

P

UN

C

T

U

RE

BA

T

E

R

I

E

S

.

N

E

PA

S

I

NC

I

N

É

RE

R

OU

P

E

R

CE

R

LE

S

P

I

L

E

S

.

M

ade

i

n

C

h

i

na

/

Fa

b

r

i

q

u

é

en

c

h

i

ne

C

R142

3

Battery installation

Install the battery, as shown below.

IMPORTANT INFORMATION:

Use only the supplied rechargeable battery or replacement battery (model BT162342/

BT262342). To order, visit our website at www.telephones.att.com or call

1 (800) 222-3111. In Canada, dial 1 (866) 288-4268.

Plug the battery connector securely into the socket inside the handset battery

compartment. Insert the supplied battery with the label THIS SIDE UP facing up,

as indicated.

1.

Align the cover flat against the battery compartment, then slide it upwards until it clicks

into place.

2.

Charge the handset by placing it face forward in

the telephone base or charger. The CHARGE light

is on when charging.

3.

CHARGE light

To replace the battery, press the tab and slide the

battery compartment cover downwards. Lift out

the old battery and disconnect it from the handset.

Follow the instructions to install and charge the

new battery.

T

H

IS

SI

D

E

U

P

/

CE

C

ÔT

É

V

ER

S

L

E HA

U

T

B

attery

P

ac

k

/

Bl

oc

-

p

i

l

e

s

:

B

T

1

62

3

42

/

B

T

2

6

2

34

2

(2

.

4V

3

00

m

Ah

N

i

-M

H)

W

ARN

I

N

G

/

A

V

E

RT

I

S

E

M

E

N

T

:

D

O

NOT

BU

R

N

OR

P

UN

C

T

U

RE

BA

T

E

R

I

E

S

.

N

E

PA

S

I

NC

I

N

É

RE

R

OU

P

E

R

CE

R

LE

S

P

I

L

E

S

.

M

ade

i

n

C

h

i

na

/

Fa

b

r

i

q

u

é

en

c

h

i

ne

C

R142

3

T

H

IS

SI

D

E

U

P

/

CE

C

ÔT

É

V

ER

S

L

E HA

U

T

B

attery

P

ac

k

/

Bl

oc

-

p

i

l

e

s

:

B

T

1

62

3

42

/

B

T

2

6

2

34

2

(2

.

4V

3

00

m

Ah

N

i

-M

H)

W

ARN

I

N

G

/

A

V

E

RT

I

S

E

M

E

N

T

:

D

O

NOT

BU

R

N

OR

P

UN

C

T

U

RE

BA

T

E

R

I

E

S

.

N

E

PA

S

I

NC

I

N

É

RE

R

OU

P

E

R

CE

R

LE

S

P

I

L

E

S

.

M

ade

i

n

C

h

i

na

/

Fa

b

r

i

q

u

é

en

c

h

i

ne

C

R142

3

Battery charging

Once you have installed the battery, the screen indicates the battery status (see the

following table). If necessary, place the handset in the telephone base or charger to

charge the battery. For best performance, keep the handset in the telephone base

or charger when not in use. The battery is fully charged after 16 hours of continuous

charging. See Technical specifications on page 36 for battery operating times.

If the screen is blank, you need to charge the handset without interruption for at least

30 minutes to give the handset enough charge to use the telephone for a short time.

The screen shows Low battery until you have charged the battery without interruption

for at least 30 minutes. The following table summarizes the battery charge indicators

and actions to take.

Battery indicators Battery status Action

The screen is blank or shows

Put in charger.

Battery has no or very little

charge. The handset cannot

be used.

Charge without interruption

(at least 30 minutes).

The screen shows

Low battery and flashes.

Battery has enough charge

to be used for a short time.

Charge without interruption

(at least 30 minutes).

The screen shows HANDSET X

and the battery icon shows .

Battery is charged. To keep the battery charged,

place it in the telephone base or

charger when not in use.

notes:

If you are on a call in low battery mode, you hear 4 short beeps every 50 seconds.

If no battery is installed in the handset when you place it in the telephone base or charger, the

screen shows No battery. Follow the instructions in Battery installation on page 3 to install

the battery.

•

After you install your telephone or power returns following a power

outage, the handset will prompt you to set the date and time (see

page 8). To skip setting the date and time, press OFF/CANCEL.

Date: MM/DD/YY

ECO

4

Handset overview

CHARGE light

On when the handset is

charging in the telephone

base or charger.

CID/VOLUME

Press to scroll down while

in menus.

Press to decrease the

listening volume.

Press to show the caller ID

log when the handset is not

in use.

While entering names or

numbers in the directory,

press to move the cursor to

the left.

•

MENU/SELECT

Press to display the menu.

Once in the menu, press to

select an item or save an

entry or setting.

•

QUIET

#

Press and hold to set and

turn on the quiet mode, or

turn it off.

When reviewing a caller ID

log entry, press repeatedly

to view other dialing

options.

•

DIR/VOLUME

Press to scroll up while in

menus.

Press to increase the

listening volume.

Press to show directory

entries when the handset is

not in use.

While entering names or

numbers in the directory,

press to move the cursor to

the right.

•

/SPEAKER

Press to turn on the handset

speakerphone, press again to

resume normal handset use.

PHONE/FLASH

Press to make or answer

a call.

During a call, press to

answer an incoming call

when you receive a call

waiting alert.

•

INT

Press to initiate an intercom

conversation or transfer a call.

1

While reviewing a caller

ID log, press repeatedly to

add or remove 1 in front

of the caller ID log before

dialing or saving it to the

directory.

Press and hold to set or

dial your voicemail number.

•

5

REDIAL/PAUSE

Press repeatedly to review

the last 10 numbers dialed.

While entering numbers,

press and hold to insert a

dialing pause.

•

MUTE/DELETE

During a call, press to mute

the microphone.

While predialing, press to

erase digits.

While reviewing the redial

list, directory, speed dial

list or caller ID log, press to

delete an individual entry.

•

TONE

Press to switch to tone dialing

temporarily during a call if you

have pulse service.

OFF/CANCEL

During a call, press to hang

up.

While using menus, press

to cancel an operation,

back up to the previous

menu, or exit the menu

display; or press and hold

to exit to idle mode.

Press and hold while the

handset is not in use to

erase the missed call

indicator.

•

6

/HANDSET LOCATOR

Press to page all handsets.

X/DELETE

Press to delete the message currently

playing.

Press twice to delete all old messages when

the telephone is not in use.

•

Telephone base overview

/SKIP

Press to skip a message.

Message window

Displays the number of messages or other

answering system information.

/ANS. ON/OFF

Press to turn the built-in answering system on

or off.

/PLAY/STOP

Press to start or stop message playback.

During call screening, press to temporarily

turn the call screening on or off.

•

/ /-VOLUME+

When the telephone is not in use, press to

adjust the telephone base ringer volume.

During call screening or message playback,

press to adjust the listening volume.

•

/REPEAT

Press to repeat a message.

Press twice to play the previous message.

•

7

Menu overview

Use the menu to change the telephone settings.

Press MENU/SELECT in idle mode (when the handset is not in use) to enter the

main menu.

Press CID or DIR to scroll through menu items.

Press MENU/SELECT to select or save the indicated item.

-OR-

Press OFF/CANCEL to cancel an operation, back up to the previous menu or exit

the menu display. Press and hold OFF/CANCEL to cancel an operation and return

to idle mode.

Feature summary

Default settings are indicated by an asterisk (*).

Screen display Function Options

LCD language Set the display language as English, French

or Spanish.

English*

Français

Español

Voicemail # Set the speed dial voicemail number. Voicemail #

-

Clr voicemail Turn off the voicemail indicator. Reset VM Icon?

Key tone Set whether there are beeps when you press keys. On*

Off

Set date/time Set date and time of the telephone system. Date: MM/DD/YY

Time: HH:MM

- -

Home area code Set the telephone to recognize calls with the home

area code.

Home area code

---

Dial mode Set whether outgoing calls use pulse dialing or

tone dialing.

Pulse

Touch-tone*

Call screening Set whether incoming calls are played through the

speaker while they are being recorded.

On*

Off

# of rings Set how many times the telephone rings before the

answering system answers an incoming call.

6, 5, 4, 3*, 2,

Toll saver

Remote code Select a 2-digit number to allow remote access from

another telephone (away from your home or office).

19*

Msg alert tone Set whether there is an audible message alert every

10 seconds when there are new messages.

On

Off*

Recording time Set how long a message can be recorded. 3 minutes*

2 minutes

1 minute

Voice language Set the voice prompt language in your answering

system.

English*

Français

1.

2.

3.

8

Telephone settings

Use Feature summary on page 7 to find and set features. The following are a few

examples of common features to set. Refer to Handset settings and Answering

system settings in the online user’s manual for detailed instructions on setting all

telephone features.

Handset ringer volume

You can set the handset ringer volume level, or turn the ringer off. When the ringer is

off, and Ringer off appear on the handset screen.

Press MENU/SELECT when the handset is in idle mode.

Press CID or DIR to scroll to Ringers, then press MENU/SELECT

twice to select Ringer volume.

Press CID or DIR to sample each volume level.

Press MENU/SELECT to save your preference.

note: If the handset ringer volume is off, that handset ringer is silenced

for all incoming calls; however, that handset still plays the paging tone

when responding to the handset locator feature.

Telephone base ringer volume

When the telephone is not in use, press / /-VOLUME+ on the telephone base to

adjust the ringer volume.

Date and time

The answering system announces the day of the week and time of each message

received prior to playing it. If you subscribe to caller ID service, the day, month and time

are set automatically with each incoming call. However, the year must be set so that the

day of the week can be calculated from the caller ID information.

Press MENU/SELECT when the handset is in idle mode.

Press CID or DIR to scroll to Set date/time, then press

MENU/SELECT.

Press CID or DIR to select the month, then press

MENU/SELECT or enter the 2-digit number (01-12) using the

dialing keys.

Press CID or DIR to select the day, then press MENU/SELECT

or enter the 2-digit number (01-31) using the dialing keys.

Press CID or DIR to select the year or enter the 2-digit

number (00-99) using the dialing keys, then press

MENU/SELECT.

Press CID or DIR to select the hour, then press MENU/SELECT

or enter the 2-digit number (00-23) using the dialing keys.

Press CID or DIR to select the minute, then press

MENU/SELECT or enter the 2-digit number (00-59) using the

dialing keys.

Press CID or DIR to choose AM or PM. Press MENU/SELECT

to save.

1.

2.

3.

4.

1.

2.

3.

4.

5.

6.

7.

8.

Volume:

Ringer volume

ECO

Set date/time

ECO

Date: MM/DD/YY

ECO

Time: HH:MM - -

ECO

9

Making, answering and ending calls

Making a call

Press PHONE/FLASH or /SPEAKER and then dial the

number using the dialing keys.

-OR-

Enter the number using the dialing keys and then press

PHONE/FLASH or /SPEAKER to dial.

While predialing a number, you can:

Press and hold REDIAL/PAUSE to insert a 3-second dialing

pause (a P appears).

Press MUTE/DELETE or OFF/CANCEL to erase a digit.

Press and hold MUTE/DELETE or OFF/CANCEL to return to

idle mode.

Answering a call

Press PHONE/FLASH, /SPEAKER, or any dialing key (0-9,

or #).

Ending a call

Press OFF/CANCEL or put the handset in the telephone base or

charger to end the call.

Handset speakerphone

During a call, press /SPEAKER to switch between speakerphone and normal handset

use. Press OFF/CANCEL to hang up.

Temporary silencing

While the telephone is ringing, press OFF/CANCEL or MUTE/DELETE to silence the

ringer temporarily on that handset only. This turns off the ringer without disconnecting

the call. The next incoming call rings normally at the preset volume.

•

10

Options while on calls

Volume control

While on a call, press DIR/VOLUME to increase or press CID/VOLUME to decrease

the listening volume.

note: The handset volume setting and speakerphone volume setting are independent. Changing

one does not affect the other.

Join a call in progress

If a handset is already on a call and you would like to join the call, press

PHONE/FLASH or /SPEAKER on another system handset.

To exit the call, press OFF/CANCEL or place the handset in the telephone base or

charger. The call does not end until all handsets hang up.

notes:

This feature is only applicable to models with more than one handset.

For models with two to four handsets, all handsets can be used at the same time on an outside

call. For models with five handsets, you can use a maximum of four handsets. If the fifth

handset attempts to join the call, the handset screen shows Unable to call.

Chain dialing

While on a call, you can initiate a dialing sequence from numbers stored in the directory,

caller ID log or redial list. Doing this can be useful if you wish to access other numbers

(such as bank account numbers or access codes).

To initiate a dialing sequence from the directory, caller ID log or redial list while on a

call, access the number through the menu system:

While on a call, press MENU/SELECT, then scroll to Directory or Caller ID log.

Press MENU/SELECT.

-

OR

-

While on a call, press REDIAL/PAUSE to show the redial list.

Scroll to the desired number. If you are in directory, you can use the dialing keys to

find the desired directory entry (see Search by name in the online user’s manual for

more details).

Press MENU/SELECT to dial the displayed number.

Redial

Each handset stores the 10 most recently called numbers in the redial list.

To review and call numbers in the redial list, press REDIAL/PAUSE in idle mode. The

most recently called number appears on the screen.

To view up to 10 recently called numbers, press DIR, CID or REDIAL/PAUSE

repeatedly to scroll through the numbers in the list.

When the desired number appears, press PHONE/FLASH or /SPEAKER to dial

the number.

•

1.

2.

3.

1.

2.

3.

11

Handset locator

Use the handset locator to find misplaced handset(s).

To start the paging tone:

Press /HANDSET LOCATOR at the telephone base to

start the paging tone on all handsets for 60 seconds.

To stop the paging tone:

Press PHONE/FLASH, /SPEAKER,

OFF/CANCEL or any dialing key (0-9, or #) on

the handset(s).

-OR-

Press /HANDSET LOCATOR on the telephone base.

-OR-

Put the handset in the telephone base or charger.

•

12

Intercom

Make and answer an intercom call

You can make an intercom call between handsets.

Press INT on your handset when not in use.

If you have 2 handsets, your originating handset screen

shows Calling HS X, and the other handset screen shows

HS X is calling.

If you have more than 2 handsets, your originating handset

screen shows Intercom to. Use the dialing keys to select

the the destination handset. The destination handset screen

shows HS X is calling (X represents the handset number).

To answer the intercom call, press any dialing key (0-9, or #),

PHONE/FLASH, /SPEAKER or INT on that handset. Both

handset screens now show Intercom.

To end an intercom call, press OFF/CANCEL or place the

handset back in the telephone base or charger. Both handset

screens now show Intercom ended.

notes:

This feature is only applicable to models with more than one handset.

Before the intercom call is answered, you can cancel the intercom call by pressing

OFF/CANCEL or INT on your originating handset.

1.

•

2.

3.

•

Intercom to

ECO

Intercom

ECO

Calling HS X

ECO

13

Call transfer using intercom

You can transfer an outside call to another system handset.

During an outside call, press INT and proceed just as you would

make a normal intercom call. Once the other party has answered

the intercom call, you have the following options:

You can let the other handset join you on the outside call in

a three-way conversation. Press and hold INT on the

originating handset.

You can transfer the call. Press OFF/CANCEL or place the

handset back in the telephone base or charger. Your originating

handset screen shows Transferred. The other handset

automatically connects to the outside call.

Press INT on your originating handset to switch between the

outside call (Outside call appears on the screen) and the

intercom call (Intercom appears on the screen).

The called party can end the intercom call by pressing

OFF/CANCEL or placing the other handset back in the

telephone base or charger. The outside call continues with the originating handset.

notes:

This feature is only applicable to models with more than one handset.

To cancel the transfer and return to the outside call before the intercom call is answered, press

OFF/CANCEL, PHONE/FLASH or INT on your handset.

If the called party does not answer within 100 seconds, or if the handset is in use, on a call,

or out of range, the originating handset shows

Unable to call

on its screen and automatically

returns to the outside call.

•

Transferred

ECO

Outside call

ECO

Intercom

ECO

14

Directory

Directory overview

The directory is stored in the telephone base and shared by all handsets. It stores up to

50 entries. Changes made to the directory on any one handset apply to all. Only one

handset can review the directory at a time.

Create directory entries

Press MENU/SELECT in idle mode. Press CID or DIR to scroll to

Directory and then press MENU/SELECT.

Press MENU/SELECT to choose Add contact.

Use the dialing keys to enter the telephone number (up to 30

digits). Press MENU/SELECT to save the number in the display.

Enter the name when prompted. Use the dialing keys to enter

a name (up to 15 characters). Each time you press a key, the

character on that key appears. Additional key presses produce

other characters on that key. Refer to the Character chart

under Create directory entries of the online user’s manual for

information on entering special characters.

Press MENU/SELECT to store your new directory entry. The screen

shows Saved.

While entering names and numbers, you can edit them using the

following controls:

Press CID or DIR to move the cursor to the left or right.

Press MUTE/DELETE to erase a digit or character.

Press and hold MUTE/DELETE to erase all digits or characters.

While entering telephone numbers, press and hold REDIAL/PAUSE to enter a

3-second dialing pause (a P appears).

While entering a name, press 0 to add a space.

Review directory entries

Press DIR when in idle mode. The screen briefly shows the directory summary

followed by the first entry in the directory.

Press CID or DIR to browse through the directory or use the dialing keys (0-9) to

start a name search. Entries appear alphabetically by the first letter in the name.

note: If the telephone number in the directory exceeds 15 digits, a dash appears after the

14th digit, and the remaining digits are displayed after two seconds beginning with a dash.

1.

2.

3.

4.

5.

•

1.

2.

Enter number

888-883-2445_

ECO

Charlie Johnson_

ECO

Add contact

ECO

15

Dial a directory number

When the desired directory entry displays, press PHONE/FLASH or /SPEAKER

to dial.

Edit a directory entry

When the desired directory entry displays on the screen, press MENU/SELECT.

Edit the telephone number, then press MENU/SELECT.

Edit the name.

Press MENU/SELECT to save.

Delete a directory entry

When the desired directory entry displays on the screen, press MUTE/DELETE and then

press MENU/SELECT to confirm.

Speed dial

There are 9 speed dial locations (0 and 2-9) where you can store telephone numbers

you wish to dial more quickly. Speed dial assignments can only be selected from the

existing directory entries. The speed dial locations are shared by all handsets. Changes

made apply to all handsets.

Enter a speed dial number

Press MENU/SELECT when the handset is in idle mode. Press CID

or DIR to scroll to Directory and then press MENU/SELECT.

Press CID or DIR to choose Speed dial, then press

MENU/SELECT.

Press CID or DIR to scroll to the desired speed dial location,

then press MENU/SELECT.

Press CID or DIR to scroll to the desired entry you wish to

assign to the selected speed dial location, or use the dialing keys

to start a name search.

When the desired directory entry displays, press MENU/SELECT.

Dial a speed dial number

When in idle mode, press and hold the desired speed dial location

(0 or 2-9) to dial.

1.

2.

3.

4.

1.

2.

3.

4.

5.

•

Speed dial

ECO

0:<Unassigned>

ECO

Charlie Johnson

888-883-2445

ECO

0:Charlie Johnson

16

Caller ID

This product supports caller ID services offered by most telephone service providers.

Caller ID allows you to see the name, number, date and time of calls. The available

caller ID information will appear after the first or second ring.

Missed (new) call indicator

The telephone base stores the last 50 incoming calls as the caller ID information. When

a handset is in idle mode and has new or missed calls, the screen shows XX missed

calls. If you do not want to review the missed calls one by one, but still want to keep

them in the caller ID log, you can press and hold OFF/CANCEL for 4 seconds when

the handset is idle.

Review the caller ID log

When a handset is in idle mode, press CID.

Press CID or DIR to scroll through the list.

Press # (pound key) repeatedly to show different dialing options.

Press 1 repeatedly if you need to add or remove 1 in front of the telephone

number before dialing or saving it in the directory.

Press PHONE/FLASH or /SPEAKER to dial the displayed telephone number.

Delete entries from the caller ID log

To delete one entry:

When viewing an entry, press MUTE/DELETE to delete the entry from the caller ID log.

To delete all entries:

On a handset, press MENU/SELECT in idle mode.

Press CID or DIR to scroll to Caller ID log, then press

MENU/SELECT.

Press CID or DIR to scroll to Del all calls, then press

MENU/SELECT twice. Once deleted, you cannot retrieve

the entries.

Store a caller ID entry in the directory

On a handset, press CID in idle mode.

Press CID or DIR to scroll through the list.

When the desired entry displays on the screen, press MENU/SELECT. The screen

shows Edit number. If necessary, modify the number (page 14).

Press MENU/SELECT to continue. The screen shows Edit name. If necessary, modify the

name (page 14).

Press MENU/SELECT to save.

1.

2.

•

3.

1.

2.

3.

1.

2.

3.

4.

5.

Del all calls

ECO

17

Answering system and voicemail

Your telephone has separate indicators for two different types of voice messages: those

left on its built-in digital answering system and those left on your service provider’s

voicemail (fees may apply). Your telephone’s built-in answering system messages and

voicemail messages are separate. Each alerts you to new messages differently.

If XX new messages displays on the handset screens and the message window

on the telephone base flashes, there are new messages recorded on the built-in

answering system. If you turn on Msg alert tone, the telephone base beeps every

10 seconds when there are new answering system messages. To listen to your

message(s), press MENU/SELECT twice on the handset (page 19) or press

/PLAY/STOP on the telephone base (page 19).

If and New voicemail display on the handset, your telephone service provider

is indicating that it has new voicemail for you. To listen to your voicemail, dial an

access number provided by your telephone service provider, followed by a security

code or PIN. Refer to Voicemail waiting (visual message waiting) indicator in the

online user’s manual for a full description of the voicemail indicators.

Some service providers bundle or combine multiple services like voicemail and call

waiting, so you may not be aware that you have voicemail. To check what services you

have and how to access them, contact your telephone service provider.

You can use the telephone answering system and voicemail together by setting your

built-in answering system to answer before voicemail. Refer to Using the answering

system and voicemail together in the online user’s manual for instructions.

Turn the answering system on or off

You can turn the answering system on or off by pressing the /ANS. ON/OFF key on

the telephone base or through the Answer on/off menu in the handset.

note: You can turn the answering system on or off from either the handset or the telephone

base, but you can use only the handset to change the other answering system settings.

Announcement

The announcement is the greeting callers hear when calls are

answered by the answering system. The telephone has a default

announcement. You can use this announcement, or record your

own announcement up to 90 seconds.

On a handset, press MENU/SELECT in idle mode.

Press CID or DIR to scroll to Answering sys, then press

MENU/SELECT.

Press MENU/SELECT to scroll to Announcement. Follow the

screen and voice prompts to record a new announcement.

•

1.

2.

3.

Answering sys

ECO

Announcement

ECO

18

Number of rings

You can set the answering system to answer an incoming call after 6, 5, 4, 3, or 2 rings.

You can also select Toll saver. If toll saver is selected, the answering system answers a

call after two rings when you have new messages, and after four rings when there are

no new messages. Unless you change it, the answering system answers an incoming call

after 3 rings.

To set the number of rings:

On a handset, press MENU/SELECT in idle mode.

Press CID or DIR to scroll to Answering sys, then press

MENU/SELECT.

Press CID or DIR to scroll to Ans sys setup, then press

MENU/SELECT.

Press CID or DIR to scroll to # of rings, then press

MENU/SELECT.

Press CID or DIR to scroll and choose among 6, 5, 4, 3, 2 or

Toll saver.

Toll saver - the answering system answers a call after two

rings when you have new messages, and after four rings when there are no new

messages. This feature allows you to check for new messages and avoid paying

long distance charges if you are calling from out of your local area.

Press MENU/SELECT to save.

Call screening

If Call screening is on, the incoming messages can be played through the speaker on

the telephone base or the handsets. You can press PHONE/FLASH on the handset to

stop recording and speak to the caller.

Call screening at the handset:

If the answering system is turned on and there is an incoming call answered by the

answering system, the handset screen shows To screen call and press [SELECT],

alternately. Press MENU/SELECT on the handset to screen the call.

Call screening at the base:

You can turn call screening on or off using the handset. When call screening is off, you

can temporarily turn on the call screening by pressing /PLAY/STOP or /VOLUME+

on the telephone base. The call screening will return to off for the next incoming call.

1.

2.

3.

4.

5.

•

6.

# of rings

ECO

3

ECO

La page est en cours de chargement...

AT&T AWX22104 Guide de démarrage rapide

AT&T AWX22104 Guide de démarrage rapide

dans d''autres langues

Documents connexes

Autres documents