Jabra BT200 - Headset - Over-the-ear Manuel utilisateur

JABRA

BT200

JABRA

BT200

FREESPEAK

JABRA BT200

User Manual

For Non Bluetooth Phones

Bluetooth Mobile Headset

FOR ALL BLFOR ALL BLUETUETOOOOTH MOBILE PHONESTH MOBILE PHONES

32

English

Introduction ....................................................................................................................................................... 4

What’s in the Package?................................................................................................................................... 5

JABRA BT300 Bluetooth Headset Features ............................................................................................. 6

Choose Right or Left Ear Wearing Style ................................................................................................... 8

Placing the Headset on your Ear ................................................................................................................ 9

Using your JABRA BT300 Headset........................................................................................................... 10

Charging & Battery Time............................................................................................................................. 13

Linking (Pairing) the Headset to the Multi-adapter.......................................................................... 15

Making a Call with the JABRA BT200 ..................................................................................................... 16

Speaker Volume & Volume Control Buttons ........................................................................................ 20

Optimising Audio Quality........................................................................................................................... 21

Using JABRA BT200 Bluetooth Phones.................................................................................................. 22

Audio & Visual Indicators ............................................................................................................................ 22

JABRA BT200 Specifications....................................................................................................................... 24

Storage of Headset........................................................................................................................................ 24

Certification & Safety Approvals / General Information.................................................................. 25

Warranty & Parts Replacement ................................................................................................................. 26

English ....................................................................................... 3

Français

................................................................................. 29

Deutsch ................................................................................. 57

Italiano

................................................................................... 83

Nederlands ..................................................................... 111

Español

............................................................................... 139

Dansk

................................................................................... 166

Suomi ................................................................................... 193

Svenska

.............................................................................. 219

PART NUMBER BT200-31 REVISION NUMBER Revision A

What’s in the Package?

Your JABRA BT200 Bluetooth headset includes a Bluetooth headset, Bluetooth

Multi-Adapter and charging solution.

Enclosed in this package you will find:

•

One JABRA BT200 Bluetooth headset (Headset Includes One JABRA MiniGel

™

)

•

One JABRA Multi-Adapter – Bluetooth Adapter, Audio Connector, headset holder and

battery charger.

•

One JABRA mains power adapter – used with the Multi-Adapter for charging the

headset and Multi-Adapter batteries.

(Please use only the supplied compatible charger for this device)

•

One removable charging cradle clip – to attach the headset to you for easy carrying

•

One JABRA Audio socket adapter (included in certain versions)

•

One small stylus for ‘pairing’ the Multi-Adapter.

•

Two spare JABRA MiniGels

™

•

One JABRA BT200 User Guide

Introduction

The JABRA BT200 Bluetooth Headset is a lightweight wireless headset utilising Bluetooth

technology. The Bluetooth Multi-Adapter supplied plugs directly into your non-Bluetooth

phone to allow convenient cordless connection. (Connection varies with phone model

and may require an audio adapter) The Headset contains a microphone and a speaker,

and is intended for hands free communications with mobile phones. Power for the

Bluetooth Multi-Adapter and Headset are provided by an integral rechargeable battery.

The battery must be charged with the supplied charger / holder and mains power

adapter. Battery Life is approximately 3 hours (“Talk Time”) and 96 hours standby time.

Please read this user booklet before you start using the product and make sure that you:

•

Fully charge your JABRA BT200 headset and Multi-Adapter before you use it the first

time. (see Page 13)

•

Make sure that connect the Multi-Adapter to your mobile phone before you start

making calls. (see page 16)

Thank you for choosing the JABRA BT200, we hope that you are

happy with your choice!

54

4

6

10

9

5

8

3

7

2

1

JABRA BT200 Bluetooth Headset Features

1. Headset Indicator Light (BLUE LED) – Indicates the status of the headset.

2. Multi-Function Button (MFB): controls various functions of the headset.

3. Volume Control Button: adjusts the speaker (receive) volume + / -.

4. Speaker: for incoming audio.

5. Microphone: voice input for outgoing audio.

6. MiniGel

™

: One-Size-Fits-All for either ear. (JABRA BT200 should only be used with the

MiniGel in place.)

7. Charging Port: contacts for charging the battery.

8. Audio Connector: Plugs into your phone to connect the headset and phone together.

9. Stylus Switch: Switch used to ‘pair’ the Multi-Adapter with the headset or to adjust

audio quality.

10. Multi- Adapter Indicator Light (LED): Indicator used to show operating mode of the

Multi-Adapter.

76

Placing the Headset on your Ear

In order to wear the headset please follow these instructions:

1. Place the JABRA BT200

Headset behind your ear.

2. Loop the top of the headset

over the top of your ear.

3. Place the MiniGel into your

ear canal.

4. The microphone will then be

positioned in the direction of

your voice.

Choose Right or Left Ear Wearing Style

The JABRA BT200 Bluetooth headset can be worn on either ear, the MiniGel is attached to

the product for wearing on the right ear.To position for wearing on either ear please use

the simple instruction as follows:

1. Hold the headset firmly and

carefully remove the MiniGel

by gently lifting and pulling it

from the speaker housing.

2. Rotate the MiniGel 180°

from its position.

3. Replace the MiniGel onto

the speaker housing.

4. The Headset is now ready

for wearing on the left ear.

5. To change from left to right

wearing styles please repeat the

steps above rotating the MiniGel

position for either left or right ears.

98

11

To switch your headset off:

1. Press and hold the Multi-Function Button for 3 seconds until the indicator

light flashes rapidly.

2. Release the button.The headset is now turned off and the indicator light

will no longer flash.

(Please note you will need to wait at least 5 seconds before switching the

headset back on.)

Attaching the charger cradle clip

The charging cradle can be fastened to your belt or clothes

using the supplied clip.To attach the clip to the cradle follow

these simple instructions:

1. Locate the two slots on the charging cradle as shown.

2. Position the clip with one end in the top slot on the cradle.

3. Press the clip gently onto the charger cradle until the other

end fits into the bottom slot securely.

4. You will hear a clicking sound when this is correctly attached.

1

2

3

Using your JABRA BT200 Headset

The multi-adapter needs to be ON for the headset to work.To turn the multi-adapter on:

1. Remove the headset from the multi-adapter, this will automatically turn the

multi-adapter ON.

2. The multi-adapter will then be in standby mode and ready for use.

3. The indicator light will flash every 3 seconds.

4. To turn the multi-adapter OFF, simply insert the headset to the multi-adpater holder.

Turning your headset ON and OFF

To switch your JABRA BT200 on:

1. Remove the headset from the multi-adapter.

2. Press and hold the Multi-Function button firmly for at least 3 seconds until the

indicator light flashes rapidly.

3. Release the Multi-Function Button.

4. The headset will now be switched ON (standby mode) and the indicator light will

continue to slow flash every 3 seconds.

10

1312

Charging & Battery Time

Before you can use your JABRA BT200 headset, you

need to place it in its Multi-Adapter and charge it fully.

SEE FIGS 1 & 2 (Please note that the headset can be

ON or OFF while charging.) A fully charged battery

provides up to 3 hours of talktime, and up to 96 hours

of standby time.The JABRA BT200 battery does not

need to be completely used before charging – you

can re-charge the product at any time. If the charger

is left connected and charging – it will not over

charger the battery.

To charge the headset and multi-adapter , please

follow this guide:

1. Insert the travel charger’s electrical plug into an

electrical outlet.

2. Plug the mains travel charger connector into the

charger port on your multi-adapter .

1

2

Using the stylus switch

Inside the multi-adapter there is a hidden switch which

is used for a number of functions. The stylus switch is

accessible via a hole in the multi-adapter, just next to

the charging port socket. Inside the hole you will see a

small white rectangle which is the stylus switch. Using

the stylus provided in the pack, you can press the

switch when instructed in this user guide.

Using the audio adapter

Some mobile phones do not have standard sockets for

headsets to be connected. So, these phones often

have adapters available to make your phone

compatible with standard headsets. Depending on

the version of JABRA BT200 you have,your package

may include a JABRA audio adapter. To connect the

multi-adapter to your phone using the audio adapter:

1. Plug the audio adapter into your phone.

2. Plug the jack plug from the multi-adapter into the

socket on the audio adapter.

2

1

1514

Linking (Pairing) the Headset to

the Multi-adapter

Pairing creates a unique wireless link between two Bluetooth devices – such as the JABRA

BT200 headset and multi-adapter. You should NOT have to pair your headset and multi-

adapter – they have already been paired in the factory for you. If you want to use a

different JABRA multi-adapter or headset, then please follow the steps below:

1. Ensure that the main power adapter is not plugged in.

2. Ensure that the JABRA BT200 is switched OFF.

3. Using the stylus supplied, press down on the stylus switch (see Using the Stylus

Switch section) for 6 seconds until the multi-adapter indicator light stays lit. Then

Release. (Note that the indicator light will flash during the 6 seconds – but keep

pressing until on constant.)

4. Without delay, press the multi-function on/off button on the headset for 6 seconds

until it’s indicator light stays on constant.Then release the button.

5.

After a short period, both the indicator lights will flash in standby mode (every 3 seconds).

6. The headset and multi-adapter are now paired.

You will not need to repeat this process in the future because the headset and the

multi-adapter are now paired.

3. While charging,the indicator light (BLUE LED) on the headset and multi-adapter are

lit, and will remain lit, until both the headset and multi-adapter are fully charged. (The

LED will only turn on if the headset is correctly inserted into the multi-adapter.)

4. Charge the headset and multi-adapter for approximately 2 hours, or until both the

indicator lights go out.

5. You can now remove the headset from the multi-adapter and it will be ready to use.

If you remove the headset from the multi-adapter (with the power supply plugged in) the

headset will automatically turn on (standby mode). If there is an incoming call when the

headset is in the multi-adapter then you can answer the call as described in section

‘making and receiving calls’.

Low Battery Warning:

The headset needs re-charging when you hear three rapid high tones through the

headset’s speaker at 30-second intervals, and see the LED flash quickly 3 times every 3

seconds. Once the low battery warning indicators start you have 3-5 minutes of talktime

left and you will then need to follow the above steps 1-4.

1716

b) Making a Call Using Voice Dialing

1. Place the headset in the desired wearing style.

2. On the Headset - Press the Multi Function Button.

3. A short tone will prompt you to say the name of the person you wish to call (as entered

in the phone’s voicedial phonebook directory). Speak the voice ‘tag’ name.

4. The phone automatically dials your selection, and you see the details of the call

on the phone screen.

5. When connected you are free to communicate normally via the headset.

(Note : Please refer to the phone user guide for instructions on storing voice tags.)

c) Making a Call Using Voice Dialing

If your mobile phone supports voice dialing, you can use this feature with the headset.

(Voice dialing on your phone must be turned on and voice tags stored) Please refer to

your phone’s user guide for more information on voice control. (Note : Please refer to

the phone user guide for instructions on storing voice tags.)

1. Ensure that your headset is in standby mode by removing it from the multi-adapter.

2. Press the multi-function button on the headset – this puts the headset into active mode

and will establish a link between the multi-adapter and the headset.(The indicator lights

will flash every 3 seconds – you may also hear background noise as well.)

Connecting the multi-adapter to your phone

The multi-adapter needs to be connected to your phone.To enjoy cordless

communication with the JABRA BT200 simply:

1. Locate the headset socket on your phone.

2. Plug in the jack from the multi-adapter.

Making a Call with the JABRA BT200

a) Making a Call from the Mobile Phone

1. Ensure that your headset is in standby mode by removing it from the multi-adapter.

2. Place the headset on your ear in the desired wearing style.

3. Press the multi-function button on the headset – this puts the headset into active mode

and will establish a link between the multi-adapter and the headset.(The indicator

lights will flash every 3 seconds – you may also hear background noise as well.)

4. Using the phone’s keypad, dial the phone number.

5. To start the call, press the phone’s SEND / CALL key – the phone initiates the call.

6. The call will then transfer automatically to the headset when connection is made.

1918

2. Keypad First

Answer the call as usual by using the phones keypad. In this case your can then

follow instruction in the section Transferring a Call.

3. From the Multi-Adapter

If there is an incoming call and your headset is in the multi-adapter then you must:

•

Disconnect the power adapter (if plugged-in)

•

Remove the headset from the multi-adapter, and make sure it is switched on.

•

Press the headset multi-function button to put the headset in active mode.

•

Answer using the phone’s key pad.

f) Transferring a Call

To transfer a call from the phone to the headset, briefly press the headset Multi-

function button which will start the active mode. Plug the jack of the multi-adapter

into your phones headset socket.

To transfer a call from the

headset to the phone, press the multi-function button

which will place the headset in standby mode.Then remove the jack from the headset

socket on your phone.

3. Place the headset in the desired wearing style.

4. Use the phone’s keypad to initiate the voice dialling.

5. A short tone will prompt you to say the name of the person you wish to call (as

entered in the phone’s voicedial phonebook directory). Speak the voice ‘tag’name.

6. The phone automatically dials your selection, and you see the details of the call on the

phone screen.

7. When connected you are free to communicate normally via the headset.

d) Ending a call from the Headset

To end a call when wearing the headset - press the headset’s Multi Function Button.

Or you can simply end the call from the phone keypad.

e) Receiving/Answering a Call

Any of three methods can be used to answer a call. In each way you must first press

the multi-function button on the headset to put it into ‘active’mode. During active

mode the LED will flash every second.

1. Headset First

Briefly press the multi-function button to make the headset active – then answer the

call from the phones keypad in the usual way.

2120

Optimising Audio Quality

On some phone models you may hear the echo of your own voice when you are talking.

You will then need to lower the echo level by adjusting the volume of your multi-adapter.

To adjust the echo level you need to use the stylus switch and follow these instructions:

•

Ensure the AC mains power is not plugged in.

•

Ensure the multi-adapter is in active mode. (see Answering a Call)

•

Use the stylus supplied to press and hold down the switch for more than 6 seconds

until the multi-adapter indicator light stays on constant.

•

This is similar to the pairing process, but CONTINUE to hold the stylus switch down

while the light is ON.

•

After a few more seconds you will see 1, 2 or 3 longer ‘blinks’ (flashes). After the

blinking stops, the standard standby mode will flash every 3 seconds.There will also

be ‘beeps/tones’in then headset – you may find it easier to listen.

•

The number of tones or flashes corresponds to the output level of the multi-adapter.

•

1 Tone / Blink High Setting

•

2 Tone / Blink Medium Setting

•

3 Tone / Blink Low Setting

Speaker Volume & Volume Control Buttons

The JABRA BT200 offers louder speaker

volume than most headsets due to its active

battery powered amplifier.You can adjust the

volume to 8 pre-set levels.Volume up (+) and

volume down (–) button will regulate the

volume to the speaker in these 8 steps. One

step per key press increases / decreases the

desired volume until a satisfactory level is

reached.An audible tone is played for each

step +/- and when either the minimum or

maximum volume has been achieved.

2322

Multi-Adapter State LED Indication State

Power ON LED ON – with JABRA BT200 in the multi-adapter

Pairing Mode LED ON – with JABRA BT200 in the multi-adapter

Standby Mode Flashes every 3 seconds – no audio link between

headset & adapter

Active Mode Flashes every 1 second – call in progress and linked.

Audio Indicator Chart

Headset State Audio Indication

Volume limit Repeated single tone when either lower or upper

limit achieved

Low Battery Tone Three rapid tones repeated every 30 seconds

Out of Range No audio indications, deterioration of audio quality will

alert user

Incoming Call Ring tone

Pairing Confirmation Single High Pitch Tone

Active Mode Quick series of 4 tones – low to high.

Power On/OFF Quick Series of 4 Tones – low to high pitch.

Using JABRA BT200 with Bluetooth Phones

If you purchase a new Bluetooth enabled mobile phone you only need to pair the

headset and phone together. You do not need to but a new headset product – the JABRA

BT200 headset only will then work with the Bluetooth phone without the need for the

multi-adapter or phone connector.

Audio & Visual Indicators

Indicator Light Chart

Headset State LED Indication State

Power Off LED OFF

Standby Mode LED ON – Flashes every 3 seconds

Charging In Process LED ON – (while in charging cradle)

Charging Complete LED OFF – (while in charging cradle)

Low Power LED ON – Rapid flashes

Pairing Mode LED ON – Constant

Pairing Successful LED – Series of blue rapid flashes

Active / On Call Indicator LED – Flashes every second

2524

Certification and Safety Approvals /

General Information

This product is CE marked according to the provisions of the R & TTE Directive

(99/5/EC).

Hereby, GN Netcom, declares that this product is in compliance with the

essential requirements and other relevant provisions of Directive 1999/5/EC.

For further information please consult http://www.gnnetcom.com.

Please note that this product uses radio frequency bands not harmonised within EU.

Within the EU this product is intended to be used in Austria, Belgium, Denmark,

Finland, France, Germany, Greece, Ireland. Italy, Luxembourg, The Netherlands,

Portugal, Spain, Sweden, United Kingdom and within EFTA in Iceland, Norway

and Switzerland.

Users are not permitted to make changes or modify the device in any way. Changes

or modifications not expressly approved by JABRA (GN Netcom) will void the users

authority to operate the equipment.

BLUETOOTH is a trademark owned by the Bluetooth SIG, Inc.

JABRA BT200 Specifications

Bluetooth Compliance Bluetooth 1.1 with Headset Profile

Bluetooth Power 2.5 Milliwatts (0.0025 watts)

Maximum Cordless Distance 30 Feet (10 meters)

Weight of Headset 23g / 0.8oz

Typical Standby Time 96 Hours

Typical Talktime 3 Hours

Typical Re-Charge Time 2 Hours

Battery Type Lithium Polymer (Rechargeable)

Other Comments NOT Waterproof

Storage Of Headset

1. Always store the JABRA BT200 with power off and safely protected.

2. Avoid storage at high temperatures (above 60 °C / 134°F) – such as in a hot vehicle or

in direct sunlight. (Storage at high temperatures can degrade performance and

reduce battery life.)

3. Do not expose the headset or any of its supplied parts to rain or other liquids.

2726

•

Any implied warranty on JABRA (GN Netcom) products is limited to two years from

the date of purchase on all parts, including any cords and connectors.

•

Specifically exempt from any warranty are limited-life consumable components

subject to normal wear and tear, such as microphone windscreens, ear cushions,

decorative finishes, batteries, and other accessories.

•

JABRA (GN Netcom) is not liable for any incidental or consequential damages arising

from the use or misuse of any JABRA (GN Netcom) product.

•

This warranty gives you specific rights and you may have other rights which vary from

area to area.

•

Unless otherwise instructed in the User Guide, the user may not, under any

circumstances, attempt to perform service, adjustments or repairs on this unit,

whether in or out of warranty. It must be returned to the purchase point, factory or

authorised service agency for all such work.

•

JABRA (GN Netcom) will not assume any responsibility for any loss or damage

incurred in shipping.Any repair work on JABRA (GN Netcom) products by

unauthorised third parties voids any warranty.

Warranty & Parts Replacement

Battery: The JABRA BT200 is equipped with a lithium polymer rechargeable battery.

Replacement or service must be done at a qualified service centre or returned to the

manufacturer. Use only the battery supplied.

Use only the supplied and approved AC charger.

JABRA (GN Netcom) warrants this product against all defects in material and

workmanship for a period of one year from the date of original purchase.The conditions

of this warranty and our responsibilities under this warranty are as follows:

•

The warranty is limited to the original purchaser.

•

A copy of your receipt or other proof of purchase is required.Without proof of

purchase, your warranty is defined as beginning on the date of manufacture as

labelled on the product.

•

The warranty is void if the serial number, date code label or product label is removed,

or if the product has been subject to physical abuse, improper installation,

modification, or repair by unauthorised third parties.

•

The responsibility of JABRA (GN Netcom) products shall be limited to the repair or

replacement of the product at it’s sole discretion.

Français

Introduction .....................................................................................................................................................30

Contenu du paquet .......................................................................................................................................31

Fonctions du casque Bluetooth JABRA BT200 ...................................................................................32

Choisir l’oreille sur laquelle porter le casque ......................................................................................34

Placement du casque sur l’oreille ............................................................................................................35

Utilisation du casque JABRA BT200 ........................................................................................................36

Temps de chargement et durée de vie de la pile ..............................................................................39

Coupler (associer) le casque au multi-adaptateur .............................................................................41

Effectuer un appel à partir du JABRA BT200 .......................................................................................42

Volume du haut-parleur et réglage du volume...................................................................................47

Optimiser la qualité audio ..........................................................................................................................48

Utilisation du JABRA BT200 avec des mobiles Bluetooth ...............................................................49

Indicateurs sonore et visuel .......................................................................................................................50

Spécifications JABRA BT200 .......................................................................................................................52

Rangement du casque .................................................................................................................................52

Certification et exigences de sécurité / Informations générales ....... ..........................................53

Garantie et Remplacement des pièces ..................................................................................................54

2928

3130

Introduction

Le casque Bluetooth JABRA BT200 est un casque ultra-léger sans fil qui fonctionne sur la

base de la technologie Bluetooth. Le multi-adaptateur Bluetooth fourni se branche

directement sur votre mobile, même s’il n’est pas Bluetooth, pour un branchement sans fil

pratique. (Le branchement varie en fonction du modèle et peut nécessiter un adaptateur

audio). Le casque se compose d’un microphone et d’un haut-parleur, et permet d’utiliser

un téléphone portable en mains libres. L’alimentation électrique du multi-adaptateur et

du casque Bluetooth est fournie par une pile entièrement rechargeable. Il est impératif de

ne recharger la pile qu’avec le chargeur/support fourni et avec l’adaptateur secteur. La

pile assure environ 3 heures de conversation et 96 heures d’autonomie en veille.

Lisez attentivement cette brochure avant d’utiliser le produit et assurez-vous que :

•

La pile de votre casque JABRA BT200 et du multi-adaptateur est totalement chargée

avant toute première utilisation. (voir Page 39)

•

Vérifiez que le multi-adaptateur de votre mobile est bien branché au téléphone avant

d’effectuer vos appels. (voir Page 42)

Merci d’avoir choisi le JABRA BT200.Nous espérons que vous êtes

satisfait(e) de votre choix !

Contenu du paquet

Votre ensemble casque Bluetooth JABRA BT200 est livré avec un casque, un multi-

adaptateur et un dispositif de recharge Bluetooth.

Vous trouverez dans ce paquet :

•

un casque Bluetooth JABRA BT200 (le casque est livré avec un JABRA MiniGel

™

)

•

un multi-adaptateur JABRA : adaptateur Bluetooth, connecteur audio, support casque

et chargeur pile

•

un adaptateur électrique JABRA (à utiliser avec le multi-adaptateur pour recharger le

casque et les piles du multi-adaptateur) ; (veuillez utiliser exclusivement des chargeurs

agréés et compatibles avec cet appareil)

•

un clip amovible de rechargement du support (pour fixer le casque sur vous et en

faciliter le transport)

•

un adaptateur prise audio JABRA (fourni dans certaines versions)

•

un petit stylet pour « coupler » le multi-adaptateur

•

deux JABRA MiniGels

™

de rechange

•

un guide d’utilisation JABRA BT200

3332

Fonctions du casque Bluetooth

JABRA BT200

1. Voyant indicateur du casque (LED bleu) : indique l’état actuel du casque.

2. Bouton multifonctions (BMF) : commande les diverses fonctions du casque.

3. Commande Volume : permet de régler le volume (réception) du haut-parleur +/-.

4. Haut-parleur : pour l’entrée audio.

5. Micro : entrée voix pour la sortie audio.

6. MiniGel

™

: taille unique adaptable indifféremment sur l’oreille droite ou gauche (le

JABRA BT200 doit être utilisé uniquement après avoir mis le MiniGel en place).

7. Dispositif de chargement : contacts pour le chargement de la pile.

8. Connecteur audio : se branche sur le téléphone pour assurer la connexion entre le

casque et le mobile.

9. Interrupteur stylet : commutateur utilisé pour « coupler » le multi-adaptateur au

casque ou pour régler la qualité audio.

10. Indicateur visuel (LED) multi-adaptateur : voyant utilisé pour afficher que le multi-

adaptateur fonctionne.

4

6

10

9

5

8

3

7

2

1

3534

Choisir l’oreille sur laquelle porter le casque

Le casque Bluetooth JABRA BT200 se porte sur n’importe quelle oreille. Le MiniGel est

positionné sur le produit pour un port sur l’oreille droite. Pour le configurer pour un port

sur l’une ou l’autre oreille,suivez simplement les instructions ci-dessous :

1. Maintenir fermement le casque et

enlever délicatement le MiniGel en

soulevant doucement pour le détacher

du logement du haut-parleur.

2. Faire tourner le MiniGel de 180 degrés

par rapport à sa position actuelle.

3. Replacer le MiniGel sur le logement

du haut-parleur.

4. Le casque est prêt à être porté sur

l’oreille gauche.

5. Pour modifier la disposition pour un port

sur l’oreille droite au lieu de l’oreille

gauche, répéter les étapes ci-dessus en

faisant tourner le MiniGel de manière à le

porter sur l’oreille gauche ou droite.

Placement du casque sur l’oreille

Pour porter le casque, suivez les instructions suivantes :

1. Placer le casque JABRA BT200

derrière l’oreille.

2. Faire passer le haut du casque

par-dessus l’oreille.

3. Placer le MiniGel dans le

canal auriculaire.

4. Le microphone est alors positionné

en direction de la voix.

3736

Utilisation du casque JABRA BT200

Le multi-adaptateur doit être sur ON pour que le casque fonctionne. Pour mettre le multi-

adaptateur en marche :

1. Enlever le casque du multi-adaptateur : celui-ci se met automatiquement sur ON.

2. Le multi-adaptateur passe ensuite en mode veille. Il est prêt à l’emploi.

3. Le voyant clignote toutes les 3 secondes.

4. Pour arrêter le multi-adaptateur (position OFF), insérez simplement le casque dans le

support du multi-adaptateur.

Mise en marche et arrêt (ON/OFF) de votre casque

Pour mettre le JABRA BT200 en marche :

1. Ôtez le casque du multi-adaptateur.

2. Appuyez sur le bouton multifonctions et maintenez-le fermement pendant au moins

3 secondes jusqu’à ce que le voyant indicateur clignote rapidement.

3. Relâchez le bouton multifonctions.

4. Le casque est maintenant en position Marche/ON (mode veille) et le voyant indicateur

continue de clignoter lentement toutes les trois secondes.

Pour arrêter le casque :

1. Appuyez sur le bouton multifonctions et maintenez-le fermement pendant au moins

3 secondes jusqu’à ce que le voyant indicateur clignote rapidement.

2. Relâchez le bouton. Le casque est maintenant éteint et le voyant indicateur ne

clignote plus.

(Remarque : vous devrez attendre au moins 5 secondes avant de remettre le casque

en marche).

Fixer le clip du support de chargement

Le support de chargement peut se fixer à la ceinture ou sur les

vêtements à l’aide du clip fourni. Pour fixer le clip sur le

support, suivez simplement les instructions suivantes :

1. Repérer les deux encoches du support de chargement comme

indiqué sur le cliché.

2. Placer une extrémité du clip dans l’encoche supérieure du support.

3. Appuyer doucement sur le clip pour l’enfoncer dans le support de

chargement jusqu’à ce que l’autre extrémité s’adapte parfaitement

dans l’encoche inférieure.

4. Vous entendrez un petit « clic » lorsque le dispositif est bien en place.

1

2

3

3938

Utilisation de l’interrupteur du stylet

Le multi-adaptateur est équipé d’un interrupteur caché utilisable

pour de multiples fonctions. L’interrupteur du stylet est accessible

via un orifice du multi-adaptateur, juste à côté de la prise du port

de rechargement.À l’intérieur du trou, vous verrez un petit

rectangle blanc : il s’agit de l’interrupteur du stylet.En utilisant le stylet

fourni avec l’ensemble, vous pouvez appuyer sur l’interrupteur selon les

instructions figurant dans le présent guide d’utilisation.

Utilisation de l’adaptateur audio

Le branchement ordinaire de casques n’est pas prévu sur certains téléphones mobiles. Ces

téléphones disposent fréquemment d’adaptateurs permettant de faire en sorte que votre

téléphone soit compatible avec des casques ordinaires. En

fonction de la version du JABRA BT200 dont vous disposez,

votre ensemble pourra inclure un adaptateur audio JABRA.

Pour brancher le multi-adaptateur sur votre téléphone à

l’aide de l’adaptateur audio :

1. Branchez l’adaptateur audio sur votre téléphone.

2. Branchez la fiche mâle du multi-adaptateur dans la prise

femelle de l’adaptateur audio.

Temps de chargement et

durée de vie de la pile

Avant de pouvoir utiliser votre casque JABRA BT200, vous

devez le placer sur son multi-adaptateur et le charger

complètement. SE REPORTER AUX SCHÉMAS 1 et 2 (Notez

que le casque peut fonctionner ou non en mode

chargement). Une pile entièrement chargée assure jusqu’à

3 heures de fonctionnement en conversation et plus de 96

heures en veille (hors conversation). Il n’est pas nécessaire

que la pile du JABRA BT200 soit entièrement épuisée avant

de procéder au chargement : vous pouvez recharger

l’appareil à tout moment. Si vous laissez le chargeur

connecté et en charge, il ne surchargera pas la pile.

Pour charger le casque et le multi-adaptateur, veuillez

procéder de la manière suivante :

1. Insérer la fiche électrique du chargeur de voyage dans

une prise électrique.

2. Brancher l’autre fiche du chargeur de voyage sur le port

de chargement de votre multi-adaptateur.

1

2

1

La page charge ...

Jabra BT200 - Headset - Over-the-ear Manuel utilisateur

Jabra BT200 - Headset - Over-the-ear Manuel utilisateur

dans d''autres langues

Documents connexes