Boneco 50241 Manuel utilisateur

Marque: Boneco

Modèle: 50241

Catégorie: Humidificateurs

Taper: Manuel utilisateur

Ce manuel convient également à

S450

S450

PLEASE READ AND SAVE

ALL INSTRUCTIONS!

LISEZ ET CONSERVEZ

TOUTES LES INSTRUCTIONS!

¡POR FAVOR LEA Y

GUARDE TODAS

LAS INSTRUCCIONES!

Instructions for use (7 – 16)

Instructions d’utilisation (17 – 26)

Instrucciones para el uso (27 – 36)

Illustrations (1 – 27)

4 7

12 15

1711

WARM

Instructions for use

PLEASE READ AND SAVE ALL THESE INSTRUCTIONS!

Important safety instructions

• Read the operating instructions carefully before using

the appliance and keep them in a safe place for later

reference.

• Connect the appliance only to AC – with voltage

indicated on the rating label.

• Always plug the power cord into the appliance first

before connecting it to the electrical outlet. CAUTION: A

sound from the unit indicates that the appliance is sup-

plied with power.

• Only use the appliance indoors and within the param-

eters stated in the technical specifications. Using the

appliance for a purpose for which it is not intended

could pose a serious hazard to health and life.

• This appliance is not to be used by persons (including

children) with impaired physical, sensory or mental

capacities or insufficient experience and knowledge.

Children should be supervised to ensure that they do

not play with the appliance (fig. 1).

• Never use the appliance if there is any damage to the

appliance or cable, after malfunction has occurred,

after the appliance has been dropped (2) or damaged

in any other way.

• Only use the original power cord.

• This appliance has a polarized plug (one blade is wider

than the other). To reduce risk of shock, this plug is

intended to fit in a polarized outlet only one way. If the

plug does not fit fully in the outlet, reverse the plug. If it

still does not fit, contact a qualified electrician. DO NOT

attempt to defeat this safety feature.

• A loose fit between the plug (receptacle) and the

AC outlet may cause overheating and a distortion

of the plug. Contact a qualified electrician to replace

loose or worn receptacles.

• ALWAYS unplug before removing/filling/emptying the

water tank, before cleaning/maintaining, assembling/

dismantling of individual parts and before moving the

appliance.

• In case the power cord is damaged, it must be

replaced by the manufacturer, an authorized service

dealer or a similarly qualified person, in order to avoid

a hazard.

• Only operate the appliance when it is completely

assembled.

• Repairs to electrical appliances may only be carried out

by qualified service engineers (3). Improper repair work

can pose a considerable hazard to the user.

• Never pull the plug from the electrical socket by the

cable or with wet hands.

• Do not operate the appliance with wet hands.

• Always place the appliance on a dry, level surface.

•

Do not immerse the main body in water or other

liquids

(16).

• Position the appliance where it cannot be easily

knocked over (4).

• Do not run the power cord under a carpet or other

objects. Position the appliance so that you will not trip

over the cord.

• Do not use the appliance in areas where combustible

materials, gases or vapours are present.

• Do not sit, stand or place any heavy objects on the ap-

pliance (keep the steam outlet clear).

• Caution: The surfaces of the unit are hot during

operation.

• During operation, do not put the power cable on top

of the appliance because of a danger of fire and short

circuit.

• Do not use an extension cord.

• Do not place the unit on hot surfaces or near open

flames. Keep a minimum distance of 1 ft.

• Never immerse the appliance or cable into water or

any other liquids because of danger of injury, fire or

electric shock.

• Only use original spare parts.

• Before cleaning, unplug the power cord and let the unit

cool completely off.

• Do not move the appliance during operation.

• The manufacturer rejects all liability for damage

caused by nonobservance of these instructions for use.

Foreword

Congratulations on choosing the S450 appliance. In do-

ing so, you have taken an important step towards healthy

indoor air and more wellbeing.

Proper use:

The appliance must only be used for the humidification of

the air indoors.

Caution: Hot steam and boiling water!

Do not allow the appliance to be used by children.

Steam and boiling water can lead to burns.

Unpacking

• Carefully remove the unit from its box.

• Remove the unit from the wrapping.

Note: the top cover of the unit is removable.

• Remove the accessories from inside the unit (5).

• Remove all packaging materials.

Description of the appliance/

Scope of delivery

Only operate the appliance when it is completely

assembled.

Putting into operation

Please make sure to observe all safety instruc-

tions!

Use the appliance only on a flat and stable

survace that is water and heat resistant. Keep

a minimum distance of 1 ft from walls, furni-

ture, and curtains (risk of moisture damage) (6).

Caution: Knocking the unit over can cause

scalding due to hot water.

Always plug the power cord into the appliance

first, before connecting it to the electrical outlet

(7). Caution: Insert the plug fully into the unit!

A sound from the unit indicates that the

appliance is supplied with power.

Please note that the appliance will produce

louder operating noises for the first few minutes

during commissioning.

Filling and refilling the tank with water

Caution: Only fill the water tank with fresh, cold

tap water. Do not use carbonated mineral water

or any other liquids.

Caution: Hot after usage!

Caution: Never pour any water into the ventila-

tion openings since this can damage the appli-

ance.

Always fill water right into the tank. Never pour water

directly into the unit or into the steam pipe (8).

Control Panel

Ventilation opening

Ventilation openings

Water tank cap

Steam pipe

Anti-Mineral Pad

Water level indicator

Steam outlet

Steam pipe cover with fragrance container

Top cover

Water tank

Power cord

Optional

Water level sensor

Steam tray

Anti-Mineral Pad

Water base

• Make sure that the unit is turned off.

• Remove the top cover of the unit (Note: formation of

condensation may occur after use on the inside of the

cover) and take the water tank from the unit by using

the tank handle (9).

• Turn the water tank upside down, unscrew the cap and

fill with water (9 – 10).

• Close the tank cap securely, place the tank into the unit

and put the cover back on (11).

SLEEP-Mode

By pressing button B, the AUTO-Mode can be changed to

SLEEP-Mode (symbol K) and vise versa. In the SLEEP-Mode,

the desired relative humidity (rH) is preset to 45%. The unit

chooses the appropriate output level Low “L” / Medium “M”

(symbol G), in order to attain the value of 45% rH as energy-

efficiently as possible.

In SLEEP-Mode, the rH can be changed at any time by using

button C; see C) Setting humidity level. If the output level

is changed by using button D, the SLEEP-Mode turns off

and the unit is operated manually; see D) Manual operation.

By pressing button B two times, the SLEEP-Mode can be

reactivated.

C) Setting humidity level

The appliance is equipped with a hygrostat. This measures

the relative humidity and switches the appliance off automat-

ically when the desired value is reached. The internal ven-

tilation remains turned on, to ensure an accurate reading of

the relative humidity. If the relative humidity falls below the

desired value, humidification resumes automatically. The

desired relative humidity can be adjusted in steps of 5% by

pressing button B. While selecting the desired humidity out-

put, the value display is blinking. The word DESIRED appears

on the display (symbol H). After a few seconds, the display

automatically changes to show the current value (symbol

H). Upon reaching the desired relative humidity, the display

shows DESIRED and CURRENT.

A relative humidity of between 40 and 60% is recom-

mended. The setting for the relative humidity ranges from a

minimum of 30% to a maximum of 70% relative humidity or

“CO” continuous mode.

Symbol E2

When the display shows “E2”, the current relative humid-

ity has reached 90%. For safety reasons, the appliance

switches off automatically. The appliance switches back

on, when the relative humidity falls below 85%.

A) Switch on/off

Pressing button A switches the appliance either on or off.

Button A is also used to start the decalcification mode. See

the section about “Decalcification Mode” (18 – 25). After

the unit is switched on, it is in AUTO-Mode (symbol J).

B) AUTO- / SLEEP-Mode

AUTO-Mode:

After the unit is switched on, it is in AUTO-Mode (symbol J).

The desired relative humidity (rH) is preset to 50%. The unit

chooses the appropriate output level Low “L” / Medium “M”

/ High “H” (symbol G), in order to attain the value of 50% rH

as quickly as possible.

In AUTO-Mode, the rH can be changed at any time by using

button C; see C) Setting humidity level. If the output level

is changed by using button D, the AUTO-Mode turns off

and the unit is operated manually; see D) Manual operation.

By pressing button B, the AUTO-Mode can be reactivated.

Operation S450

AUTO

CURRENT

DESIRED

J K

Quick display of the current relative humidity

When the unit is switched off (power cable is connected),

the current relative humidity can be shown on the display

by briefly pressing one of the C buttons. This display goes

out automatically after a few seconds.

D) Manual operation

The appliance can be operated on 3 levels. The output levels

Low “L” (night operation), Medium “M” (normal operation),

and High “H” (power operation) can be selected by press-

ing button D (AUTO- and SLEEP-Mode are deactivated). The

desired output level is shown on the display via symbol G.

E) Timer

The appliance has an OFF- and an ON-Timer.

OFF-Timer:

The OFF-Timer is set by pressing button E on the switched-

on appliance. The blinking display shows the hours until the

unit will be switched off: 0h. By pressing button C, the

switch-off time can be selected from between 0h -9h. With-

out any input, the set value is enabled after 3 seconds and

symbol L indicates that the timer is turned on. The display

once again shows the current relative humidity. By pressing

button E, the remaining time until switch-off is displayed

and can also be adjusted.

ON-Timer

By pressing button E on the turned-off appliance, the ON-

timer is set. The blinking display now shows the hours until

the unit will be switched on: 0h. By pressing button C, the

switch-on time can be selected from between 0h-9h. With-

out any input, the set value is enabled after 3 seconds. The

display shows the set switch-on time and the symbol L is

blinking. After the unit is switched on, the unit is in AUTO-

Mode (symbol J).

F) Cleaning symbol (see also section about

Decalcification-Mode)

The letter F in the display indicates that the appliance must

be cleaned. The symbol appears until the Decalcification-

Mode is completed. By pressing both C buttons simultane-

ously and holding them down for approx. 5 seconds, the

cleaning symbol can be manually reset.

G) Output level symbol

H) Current and desired relative humidity

symbol

I) Automatic shut-off „Water Tank empty“

If the water level falls below minimum level, the humidi-

fication switches off automatically. The red blinking

symbol I appears on the display. If water is not added within

5 minutes, the display turns off, except for the symbol I.

If water is added, symbol I turns off and the appliance

continues operating.

J) AUTO-Mode symbol

K) SLEEP-Mode symbol

L) Timer symbol

Fragrance container

• The steam pipe cover contains an integrated fragrance

container.

• Fill only a small amount of fragrance into the fragrance

container and do not overfill (12).

• Caution! Do not put any fragrance directly into the wa-

ter tank, water base or steam tray, as this can damage

the material and consequently the appliance (13).

Anti-Mineral Pad

CAUTION: The steam tray contains boiling water!

Remove the Anti-Mineral Pad only when the wa-

ter in the steam tray has cooled off. Place only one

Anti-Mineral Pad into the steam tray.

The Anti-Mineral Pad absorbs a large part of the resulting

lime scale while in operation. The Anti-Mineral Pad reduces

excessive calcification of the steam tray as well as the fre-

quency of necessary decalcification. In order to insert the

Anti-Mineral Pad, remove the top cover as well as the water

tank and the steam pipe from the unit (14). Now insert the

supplied Anti-Mineral Pad directly into the steam tray and

reassemble the appliance in the reversed order (14). The

Anti-Mineral Pad needs to be replaced as soon as it is com-

pletely full of lime (Anti-Mineral Pad hardens). Depending

on the hardness of the water, this needs to be done every

2 to 4 weeks. The Anti-Mineral Pad can be disposed with

the Household waste.

Cleaning of water tank and covers –

weekly (15 – 25)

Clean the water tank, top cover, fragrance

container and steam pipe with a soft plastic

brush and dish detergent and rinse well (17).

Decalcification-Mode

Only use EZCal and EZCal PRO for decalcification. Damage

that is caused by the use of other cleaning agents is not

covered by the warranty.

The Decalcification-Mode enables simple cleaning and

decalcification of the steam tray, water base, and steam

pipe.

The Anti-Mineral Pad needs to be removed, before starting

the Decalcification-Mode (18) (see section about Anti-

Mineral-Pad). Dissolve the EZCal or EZCal PRO decalcifi-

cation agents in warm water (EZCal: 32 oz / 1 L; EZCal

PRO: 14 oz / 0.5 L) and pour into the water base (19). Then

reinsert the steam pipe and top cover (20). Pressing and

holding button A for 5 seconds switches the appliance to

Decalcification-Mode (21). Decalcification-Mode is shown

on the display by the flashing symbol E (22). The value “4h”

is shown flashing on the display. Button C can be used to

change the decalcification period from 1h to 9h, depending

on the level of soiling (22). After 3 seconds without further

input, the set value is taken as “desired value” and the flash-

ing display changes back to “CURRENT”. The unit heats

up the EZCal and EZCal PRO-water solution during De-

calcification-Mode and shuts off after it is finished. The

heating of the water takes place every 30 minutes while

the Decalcification-Mode is active. The cleaning period

is now permanently displayed and switches to minutes

when the time falls below the 1 hour mark. The clean-

ing period can be changed at any time by pressing but-

ton C. At the end of the cleaning period, a short double

signal is sounded, the display shows the value “0h”

and the cleaning symbol F will rapidly flash (23). Press-

ing button A ends the Decalcification-Mode and switches

off the appliance (23).

CAUTION: The water base must now be emptied of the

EZCal and EZCal PRO and rinsed (24 – 25). Make sure no

water enters through the ventilation opening (25). Tip: In

case of excessive lime scale, decalcify overnight (12 to 15

hours).

Cleaning the housing – once or twice

annually (26).

Clean the housing with a damp rag and wipe it dry; use a

cleaning agent suitable for plastic if needed.

After usage

• Switch the appliance off by pressing button A (27).

• Disconnect power plug (15).

• Wait until the appliance has completely cooled off.

• Empty any remaining water and clean the water tank

and the water base. Decalcify if necessary.

• Let the appliance dry.

Cleaning

Always disconnect the power plug of the appli-

ance, before cleaning or rinsing (15).

The unit has to be completely emptied and

cooled off. Caution: Danger of burning!

Caution: Never pour any water into the ventila-

tion openings since this can damage the appli-

ance (24 – 25).

Important: Do not use any abrasive objects

(knives etc.) or sponges to clean the steam tray.

Never immerse the appliance in water or any

other liquids (16).

• Regular cleaning is essential for hygienic, problem-free

operation.

• Depending on water quality, regular decalcification of

the appliance is recommended (see Decalcification-

Mode).

Storing the appliance for extended periods

Clean the appliance as described earlier and allow to dry

thoroughly. Preferably store the appliance in its original box,

in a dry place away from high temperatures.

Accessories

Contact your local retailer or check our website

www.boneco.us for reorder information.

Legal notice

The appliance is cETL-listed.

Subject to technical change. The instructions for use are

Serial number

The serial number is placed on the bottom of the appliance.

Customer Service

Customer Service (USA) 1-800-336-0326

www.boneco.us

Technical data

Electrical voltage 100 – 120 V / 50/60 Hz

Power consumption up to 160 – 480 W*

Humidity output up to 3.5 gallons / 24h (13.2 L / 24 h)*

Suitable for rooms up to 860 sq ft (80 m

)

Dimensions (LxWxH) 14 x 9.5 x 13.2 inches

(35.5 x 24 x 33.4 cm)

Weight (empty) 10 lbs (4.5 kg)

Operating noise level < 35 dB(A)

Accessories Anti-Mineral Pad A451

EZCal A7417

EZCal PRO A100

*@ 120 V / 60 Hz

General Humidifier Questions

Q. Why isn’t there enough moisture in my room?

A. How often do you run the unit? If the unit is only run at

night, then during the day the moisture level will drop if

moisture is not constantly added to the air.

Q. Do you leave your door open or closed when the

unit is running?

A. a) By leaving the door open, this allows moisture to

leave the room and go into other areas of the house.

If you would like the moisture to stay within one

specific room you should consider closing the door

while the unit is running.

A. b) Wood, leather, carpet, curtains, and other types of

fabric soak up a lot of moisture, thus not leaving

enough moisture for the air. If the window is left

open, then this allows moisture to escape the room.

Another factor is a lot of times the unit is placed

next to a heating device. The idea is that the air

blowing into the room will quickly place moisture

around the room. Unfortunately, this concept does

not work because the hot air coming out of a vent

will soak up most of the moisture, and none of the

air within the room will receive any.

Q. How much moisture do I need in my room?

A. Suggested humidity levels are between 40 – 60%.

Q. What are the effects of too little or too much

humidity?

A. Dry air can cause dry skin, static electricity, out of tune

musical instruments, increased levels of dust (dry air

causes dust to rise), damage to wooden objects

(dry out and eventually cracks appear), discomfort,

sickness, and dries out nasal membranes.

Over-humidifying the air can cause mold and wallpaper

to peel.

Q. Why do I need a humidifier when I can just open

my window?

A. The moisture level within the outside air is not high

enough to humidify a room. The colder the air the less

moisture it is capable to hold, and the more the air is

heated up the percentage of relative humidity is lower.

Relative humidity means the amount of water vapor in

the air, compared to the amount the air could hold if it

was totally saturated. The difference is higher between

outside and inside temperatures; more humidification

is needed because of the dry air in the room.

Q. Where should I place my humidifier?

A. The unit should be free-standing and not close to a

wall, window, door, or thermal bridge so that air may

circulate around the unit.

Steam Humidifier Questions

Q. There is no fill-line on the water tank, how far

may I fill it up?

A. There is no fill line on the water tank, and it may be

filled all the way to the top.

Q. Humidity level is not changing or does not reach

the desired humidity level.

A. If the water tank needs refilling more than once per

day, the unit is working properly and the climatic

condition in the room has an influence on the humidity.

Reasons for low humidity level:

• air circulation is very high (air is fully exchanged

several times per day – the humidifier needs to start its

work from scratch)

• insulation of home (see air circulation)

• open space with high ceilings (not only the footage of

the room counts but also the height) – high-rise build-

ings require more humidification.

• open windows – works similar to air circulation (if it is

very cold outside don’t open the window more than

2 times per day for 3 minutes)

• big difference between outside temperature and inside

temperature – the colder the air the less moisture it

is capable to hold and the more the air is heated up

the lower is the percentage of relative humidity (=the

amount of water vapor in the air, compared to the

amount the air could hold if it was totally saturated)

• position of the unit - if it is placed close to a door,

window or air vent. This increases the air circulation.

Q. No mist / unit is not working

• If the unit is not working and the empty light is not

flashing you might have set the desired humidity too

low and the current humidity level in the room is

higher. That is why the unit switches off automatically.

Q. Water tank cap is too tight to unscrew

A. This could be a cause of the air pressure within the

water tank. Press the spring on the bottom of the water

tank cap to release air from the water tank.

Continue to do this until you are able to unscrew the

water tank cap.

Accessories

Q. What is EZCal and EZCal PRO?

A. There is a sample packet of EZCal included in the

packaging of your humidifier. EZCal and EZCal PRO are

used for cleaning and descaling any of the humidifiers

and cleans mineral build-up. EZCal and EZCal PRO are

the only recommended cleaning and descaling solu-

tions. Do NOT use any other cleaning solution since it

can damage the product. Any use of cleaning solutions

apart from EZCal and EZCal PRO will void the warranty.

Instructions for using are on the packet. Dissolve the

EZCal or EZCal PRO decalcification agents in warm

water (EZCal: 32 oz / 1 L; EZCal PRO: 14 oz / 0.5 L)

and pour into the water base. Do not change the ratio.

It can also be used for other humidifier brands. Thor-

oughly rinse the base with tap water and make sure

no EZCal and EZCal PRO residues remains in the base!

EZCal and EZCal PRO are available at selected retail

stores and online www.boneco.us.

Instructions d’utilisation

LISEZ ET CONSERVEZ TOUTES LES INSTRUCTIONS!

Consignes de sécurité importantes

• Lisez attentivement le mode d’emploi complet avant la

mise en service, et conservez-le bien pour pouvoir le

consulter ultérieurement.

• Ne branchez l’appareil qu’au courant alternatif – la

tension doit correspondre à celle indiquée sur la

plaquesignalétique de l’appareil.

• Branchez toujours d’abord le cordon d’alimentation

à l’appareil avant de le brancher dans la prise de

courant. MISE EN GARDE : L’appareil émet un son qui

indique qu’il est maintenant sous tension.

• N’utilisez l’appareil que dans des locaux d’habitation et

dans les conditions précisées dans les spécifications

techniques. Une utilisation non conforme aux spécifica-

tions peut mettre en danger la santé et la vie.

• Cet appareil n’est pas conçu pour des personnes (y

compris des enfants) ayant des facultés corporelles,

sensorielles ou mentales diminuées ou une expérience

et des connaissances insuffisantes, sauf si une per-

sonne responsable de leur sécurité les surveille ou les

assiste pendant l’utilisation de cet appareil. Les enfants

doivent être surveillés pour s’assurer qu’ils ne jouent

pas avec cet appareil (figure 1).

• Ne mettez jamais l’appareil en service lorsqu’un câble

ou l’appareil est détérioré, ni après des disfonctionne-

ments ou lorsque l’appareil a été échappé (2) ou autre

dommage quelconque de l’appareil.

• N’utilisez que le cordon d’alimentation d’origine.

• La fiche de cet appareil est polari sée (une lame est

plus large que l’autre). Afin de réduire les risques de

chocs électriques, cette fiche est conçue de fa çon à ne

pouvoir être introduite dans une prise que d’une seule

manière. Si la fiche ne s’insère pas totalement dans la

prise, retournez-la. Si elle ne s’insère toujours pas dans

la prise, con tactez un électricien qualifié. N’essayez

PAS de contourner ce dispositif de sécurité.

• Une mauvaise adaptation entre la fiche et la prise

CA peut entraîner une surchauffe et une déformation

de la fiche. Contactez un électricien qualifié pour le

remplacement de toute prise lâche ou trop usée.

• Si le cordon d’alimentation est endommagé, il doit être

remplacé par le fabricant, un distributeur de service

autorisé ou par une personne qualifiée de façon simi-

laire afin d’éviter les risques de danger.

• L’appareil doit être mis en service uniquement lorsqu’il

est entièrement assemblé.

• Débranchez TOUJOURS la prise avant d’enlever, de

remplir et de vider le réservoir d’eau; avant de nettoyer,

d’effectuer la maintenance, l’assemblage, le désas-

semblage des pièces et avant de déplacer l’appareil.

• Les réparations d’appareils électriques ne doivent

être exécutées que par des experts autorisés (3). Des

réparations non professionnelles peuvent causer des

dangers considérables pour l’utilisateur.

• Ne débranchez jamais la prise au secteur en tirant sur

le câble ou lorsque vos mains sont mouillées.

• Ne faites pas fonctionner l’appareil avec les mains

mouillées.

• Ne posez l’appareil que sur une surface sèche et plane.

• Ne plongez jamais le boîtier principal dans de l’eau ou

d’autres liquides (16).

• Placez l’appareil à un endroit tel que personne ne

puisse le heurter (4).

• Ne mettez pas le cordon d’alimentation sous un tapis

ou tout autre objet. Placez le cordon de sorte que per-

sonne ne puisse trébucher.

• N’utilisez pas l’appareil dans des pièces renfermant

des produits, gaz ou vapeurs inflammables.

• Ne montez pas, ne vous assoyez pas et ne posez pas

d’objets lourds sur l’appareil (gardez la sortie de va-

peur libre).

• Mise en garde : Pendant son fonctionnement, les

surfaces de l’appareil sont chaudes.

• Pendant son fonctionnement, ne placez pas le cordon

d’alimentation sur le dessus de l’appareil, car ceci pour-

rait occasionner un danger d’incendie et de court-circuit.

• N’utilisez pas de rallonges électriques.

• Ne placez pas l’appareil sur des surfaces chaudes ou

à proximité de flammes nues. Respectez une distance

minimale de 1 ft.

• N’immergez jamais l’appareil ou le cordon d’alimenta-

tion dans de l’eau ou dans tout autre liquide, car ceci

pourrait occasionner un danger de blessure, d’incendie

ou de chocs électriques.

• Seules les pièces de rechange d’origine du fabricant

peuvent être utilisées.

• Avant le nettoyage, débranchez le cordon d’alimentation

et permettez à l’appareil de se refroidir complètement.

• Ne déplacez pas l’appareil pendant qu’il est en marche.

• Le fabricant décline toute responsabilité pour les dom-

mages découlant du non-respect de ce mode d’emploi.

Avant-propos

Nous vous félicitons d’avoir choisi l’appareil S450. Vous

avez ainsi fait un pas important vers un air intérieur sain

et plus de bien-être.

Utilisation conforme :

L’appareil sert exclusivement à l’humidification de l’air

ambiant dans des espaces intérieurs.

Mise en garde : Vapeur chaude et eau bouil-

lante!

Ne permettez pas aux enfants d’utiliser cet

appareil. De la vapeur et de l’eau bouillante

peuvent occasionner des brûlures.

Désemballage

• Retirez l’appareil de la boîte avec soin.

• Retirez l’appareil de l’emballage. Remarque :

Le couvercle supérieur de l’appareil est amovible.

• Retirez les accessoires de l’intérieur de l’appareil (5).

• Retirez tous les matériaux d’emballage.

Description de l’appareil/Volume de la livraison

L’appareil doit être mis en service uniquement lorsqu’il

est entièrement assemblé.

Mise en service

Veuillez vous assurer d’observer toutes les

consignes de sécurité!

Utilisez l’appareil seulement sur des surfaces

planes, stables, résistantes à l’eau et à la

chaleur. Respectez une distance minimale de

1 ft des murs, des meubles et des rideaux

(risques de dommages d’humidification) (6).

Mise en garde : Renverser l’appareil peut cau-

ser un ébouillantage entraîné par l’eau chaude.

Branchez toujours d’abord le cordon d’alimen-

tation à l’appareil avant de le brancher dans la

prise de courant (7). Mise en garde : Insérez la

fiche complètement dans l’appareil! L’appareil

émet un son qui indique qu’il est maintenant

sous tension.

Veuillez noter que lors de la mise en service,

l’appareil fait un peu plus de bruit pendant les

premières minutes.

Remplissage et remplissage à nouveau du

réservoir d’eau

Mise en garde : Pour remplir le réservoir, n’uti-

lisez que de l’eau fraîche froide et potable du

robinet. N’utilisez pas d’eau minérale pétillante

ni aucun autre liquide.

Mise en garde : Chaud après usage!

Mise en garde : Ne versez jamais d’eau dans

les ouvertures de ventilation, car ceci pourrait

endommager l’appareil.

Panneau de commande

Ouverture de ventilation

Ouvertures de ventilation

Bouchon du réservoir d’eau

Tuyau de conduite de vapeur

Coussinet Anti-Minéral

Indicateur du niveau d’eau

Sortie de vapeur

Le couvercle du tuyau de conduite de vapeur pourvu d’un réservoir de

parfum

Couvercle du dessus

Réservoir d’eau

Cordon d’alimentation

En option

Capteur du niveau d’eau

Plateau de vapeur

Coussinet Anti-Minéral

Base d’eau

Remplissez toujours le réservoir d’eau directement. Ne

versez jamais d’eau directement dans l’appareil ou dans

un tuyau de conduite de vapeur (8).

• Assurez-vous que l’appareil est éteint.

• Enlevez le couvercle du dessus de l’appareil

(remarque : après usage, une formation de conden-

sation pourrait avoir lieu sur l’intérieur du couvercle)

et veuillez prendre le réservoir d’eau de l’appareil en

utilisant la poignée du réservoir (9).

• Renversez le réservoir d’eau, dévissez le bouchon et

remplissez-le d’eau (9 – 10).

• Fermez solidement le bouchon du réservoir; placez

le réservoir à l’intérieur de l’appareil et remettez le

couvercle (11).

Mode SLEEP

En appuyant sur la touche B, le mode AUTO peut être

changé au mode SLEEP (symbole K) et vice versa. Dans le

mode SLEEP, l’humidité relative souhaitée (HR) est préré-

glée à 45 %. L’appareil sélectionne le niveau approprié de

débit : Low «L» / Medium «M» (symbole G), afin d’atteindre

la valeur de 45 % HR en utilisation rationnelle de l’énergie

possible.

Dans le mode SLEEP, HR peut être modifiée en tout temps

en utilisant la touche C; voir C) Réglage du niveau d’hu-

midité. Si le niveau de débit est modifié par l’usage de la

touche D, le mode SLEEP s’éteint et l’appareil s’opère ma-

nuellement; voir D) Opération manuelle.

En appuyant deux fois sur la touche B, le mode SLEEP peut

être réactivé.

C) Réglage du niveau d’humidité

L’appareil est muni d’un hygrostat. Ceci mesure l’humidité

relative et éteint l’appareil automatiquement lorsque la

valeur souhaitée est atteinte. La ventilation interne reste

allumée pour assurer une lecture précise de l’humidité

relative. Dans le cas où l’humidité relative est inférieure à

la valeur souhaitée, l’humidification recommence automa-

tiquement. L’humidité relative souhaitée peut être réglée

en étapes de 5 % en appuyant sur la touche B. Pendant la

sélection du débit de l’humidité souhaité, la valeur sur l’écran

clignote. Le mot DESIRED apparaît sur l’écran (symbole H).

Après quelques secondes, l’écran change automatiquement

et affiche la valeur actuelle (symbole H). Lorsque l’humidité

relative souhaitée est atteinte, l’écran affiche DESIRED et

CURRENT.

Une humidité relative entre 40 % et 60 % est recommandée.

La plage de réglage de l’humidité relative est d’un minimum

de 30 % à un maximum de 70 % d’humidité relative ou

fonctionnement continu «CO».

Symbole E2

Lorsque l’écran affiche «E2», l’humidité relative actuelle a

atteint 90 %. Pour des raisons de sécurité, l’appareil se

désactive

A) Interrupteur marche/arrêt

Appuyez sur la touche A pour activer l’appareil sur marche

ou arrêt. La touche A sert aussi à commencer le mode de

décalcification. Voir le chapitre «Mode de décalcification»

(18 – 25). Lorsque l’appareil est activé, il est en mode AUTO

(symbole J).

B) Mode AUTO / SLEEP

Mode AUTO :

Lorsque l’appareil est activé, il est en mode AUTO (symbole

J). L’humidité relative souhaitée (HR) est préréglée à 50 %.

L’appareil sélectionne le niveau approprié de débit : Low

«L» / Medium «M» / High «H» (symbole G), afin d’atteindre

la valeur de 50 % HR le plus rapidement possible. Dans le

mode AUTO, HR peut être modifiée en tout temps en utili-

sant la touche C; voir C) Réglage du niveau d’humidité. Si

le niveau de débit est modifié par l’usage de la touche D,

le mode AUTO s’éteint et l’appareil s’opère manuellement;

voir D) Opération manuelle. En appuyant sur la touche B, le

mode AUTO peut être réactivé.

Commande S450

AUTO

CURRENT

DESIRED

J K

La page est en cours de chargement...

Boneco 50241 Manuel utilisateur

Marque: Boneco

Modèle: 50241

Catégorie: Humidificateurs

Taper: Manuel utilisateur

Ce manuel convient également à

S450

Télécharger le PDF

rapport

dans d''autres langues

English: Boneco 50241 User manual
español: Boneco 50241 Manual de usuario

Boneco 50241 Manuel utilisateur

Ce manuel convient également à

Boneco 50241 Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents