Kenmore 796.7142 Series Le manuel du propriétaire

Catégorie
Sèche-linge électriques
Taper
Le manuel du propriétaire

Ce manuel convient également à

Models/Modèles: 796.6142#, 796.7142#
Kenmore Elite®
Dryer
Sécheuse
P/N MFL67731060
Sears Brands Management Corporation
www.kenmore.com
Sears Canada Inc.
Toronto, Ontario, Canada M5B 2C3
www.sears.ca
Use & Care Guide
Manuel d'utilisation et d'entretien
English / Français
# = color number, code couleur
®
2
TABLE OF CONTENTS
PRODUCT RECORD
Master Protection Agreements
Congratulations on making a smart purchase. Your new
Kenmore
®
product is designed and manufactured for
years of dependable operation. But like all products,
it may require preventive maintenance or repair from
time to time. That’s when having a Master Protection
Agreement can save you money and aggravation.
The Master Protection Agreement also helps extend the
life of your new product. Here’s what the Agreement*
includes:
Parts and labor
not just for repairing defects, but to help
keep products operating properly under normal use.
Our coverage goes well beyond the product warranty.
No deductibles, no functional failure excluded from
coverage – real protection.
Expert service by a force of more than 10,000
authorized Sears service technicians, which means
someone you can trust will be working on your product.
Unlimited service calls and nationwide service, as often
as you want us, whenever you want us.
“No-lemon” guarantee – replacement of your
covered product if four or more product failures occur
within 12 months.
Product replacement if your covered product can't
be
Annual Preventive Maintenance Check at your request
– no extra charge.
Fast help by phone – we call it Rapid Resolution –
phone
support from a Sears representative on all
products. Think of us as a “talking owners manual.
Power surge protection against electrical damage due
to
$250 food loss protection annually for any food
spoilage that is the result of mechanical failure of any
covered refrigerator or freezer.
Rental reimbursement if repair of your covered
product takes longer than promised.
25% discount
repair service and related installed parts.
Once you purchase the Agreement, a simple phone call
is all that it takes for you to schedule service. You can
call at any time day or night or schedule a service
appointment online.
The Master Protection Agreement is a risk-free purchase.
If you cancel for any reason during the product warranty
period, we will provide a full refund, or a prorated refund
anytime after the product warranty period expires.
Purchase your Master Protection Agreement today!
Some limitations and exclusions apply.
For prices and additional information in the U.S.A.
call 1-800-827-6655.
*Coverage in Canada varies on some items.
For full details call Sears Canada at 1-800-361-6665.
Sears Installation Service
For Sears professional installation of home appliances,
garage door openers, water heaters, and other major
home items, in the U.S.A. call 1-844-553-6667, and in
Canada call 1-800-469-4663.
In the space below, record the date of purchase, model,
plate located inside the dryer door. Have these items of
information available whenever you contact Sears
concerning your product.
Model No
.
Date of Purchase
Serial No.
Save these instructions and your sales receipt for future
reference.
PROTECTION AGREEMENTS
IMPORTANT SAFETY INSTRUCTIONS ....................3-6
GROUNDING REQUIREMENTS ................................... 4
FEATURES AND BENEFITS
Key Parts and Components ........................................7
Accessories .................................................................. 7
INSTALLATION INSTRUCTIONS
Ke ..........................8
Location Requirements ................................................8
Choose the Proper Location .......................................8
Clearances ....................................................................8
Gas Dryers .............................................................10-11
Gas Requirements ................................................. 10
Electrical Requirements ......................................... 10
Connecting the Gas Supply ................................ 11
Electric Dryers ...................................................... 12-13
Electrical Requirements ....................................... 12
Connecting Electric Dryers ................................. 13
Venting the Dryer .................................................14-15
Connecting the Inlet Hose ......................................... 16
Leveling the Dryer ..................................................... 17
Reversing the Door Swing ........................................ 18
Final Installation Check ............................................ 19
HOW TO USE
Control Panel Features ............................................ 20
Time and Status Display .......................................... 21
Operating the Dryer .................................................22
Sorting Loads .............................................................23
Loading the Dryer .....................................................23
Cycle Guide ........................................................ 24-25
Cy ............................................ 26
Cycle Options and Special Features ..................... 27
Steam Features .......................................................... 27
USER MAINTENANCE INSTRUCTIONS
Regular Cleaning ..................................................... 28
Cleaning the Exterior .........................................28
Cleaning the Interior .......................................... 28
Cleaning Around and Under the Dryer ........... 28
Cleaning the Lint Filter ...................................... 28
Maintaining the Exhaust System ............................. 29
Kenmore Connect
TM
System ..................................30
TROUBLESHOOTING GUIDE
Before Calling for Service ................................. 31-33
WARRANTY ...................................................................34
SERVICE .......................................................... Back Cover
3
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USE
WARNING:
DANGER:
WARNING:
For your safety, the information in this manual must be followed to
minimizetheriskofreorexplosion,electricshock,ortopreventpropertydamage,personalinjury,
or loss of life.
Donotinstallaclothesdryerwithexibleplasticventingmaterials.Ifaexiblemetal(foiltype)ductisinstalled,
itmustbeofaspecictypeidentiedbytheappliancemanufacturerassuitableforusewithclothesdryers.
Flexible venting materials are known to collapse, be easily crushed, and trap lint. These conditions will obstruct
clothesdryerairowandincreasetheriskofre.
Donotstoreorusegasolineorotherammablevaporsandliquidsinthevicinityofthisapplianceorany
other appliances.
Installationandservicemustbeperformedbyaqualiedinstaller,serviceagency,orthegassupplier.
Install the clothes dryer according to the manufacturer’s instructions and local codes.
WHAT TO DO IF YOU SMELL GAS:
1. Do not try to light a match or cigarette, or turn on any gas or electrical appliance.
2. Do not touch any electrical switches. Do not use any phones in your building.
3. Clear the room, building, or area of all occupants.
4. Immediately call your gas supplier from a neighbor’s phone. Carefully follow the gas supplier’s instructions.
5.Ifyoucannotreachyourgassupplier,calltheredepartment.
Your safety and the safety of others is very important.
We have provided many important safety messages in this manual and on your appliance. Always read and
obey all safety messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word DANGER or WARNING.
These words mean:
Indicates a hazardous situation which, if not avoided, could result in death or serious injury.
Indicates a hazardous situation which, if not avoided, will result in death or serious injury.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and
tell you what can happen if the instructions are not followed.
CAUTION:
Indicates a hazardous situation which, if not avoided, could result in minor or
moderate injury.
SAVE THESE INSTRUCTIONS
4
IMPORTANT SAFETY INSTRUCTIONS
Read all instructions before using the dryer.
Before use, the dryer must be properly installed, as
described in this manual.
Do not place items exposed to cooking oils in your
dryer. Items contaminated with cooking oils may
contribute to a chemical reaction that could cause a
load to catch re.
Do not dry articles that have been previously cleaned
in, washed in, soaked in, or spotted with gasoline,
dry-cleaning solvents, or other ammable or explosive
substances, as they give o vapors that could ignite
or explode.
Do not reach into the dryer if the drum or any other
part is moving.
Do not repair or replace any part of the dryer or
attempt any servicing unless specically recommended
in this Use and Care Guide or in published user-repair
instructions that you understand and have the skills to
carry out.
Do not tamper with controls.
Before the dryer is removed from service or discarded,
remove the door to the drying compartment.
CALIFORNIA SAFE DRINKING WATER AND TOXIC ENFORCEMENT ACT
This act requires the Governor of California to publish a list of substances known to the state to cause cancer,
birth defects, or other reproductive harm and requires businesses to warn customers of potential exposure to
such substances. Gas appliances can cause minor exposure to four of these substances, namely benzene, carbon
monoxide, formaldehyde, and soot, caused primarily by the incomplete combustion of natural gas or LP fuels.
Properly adjusted dryers will minimize incomplete combustion. Exposure to these substances can be minimized
further by properly venting the dryer to the outdoors.
GROUNDING REQUIREMENTS
This appliance must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of
electric shock by providing a path of least resistance for electric current. This appliance must be equipped with
a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an
appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.
Improperconnectionoftheequipment-groundingconductorcanresultinariskof
electric shock. Check with a qualied electrician or service person if you are in doubt as to whether the appliance
is properly grounded. Do not modify the plug provided with the appliance. If it will not t the outlet, have a proper
outlet installed by a qualied electrician. This appliance must be connected to a grounded metal, permanent
wiring system or an equipment grounding conductor must be run with the circuit conductors and connected to the
equipment grounding terminal or lead on the appliance. Electrical shock can result if the dryer is not properly
grounded.
Do not allow children to play on or in the dryer. Close
supervision of children is necessary when the dryer is
used near children.
Do not use fabric softeners or products to eliminate
static unless recommended by the manufacturer of the
fabric softener or product.
Do not use heat to dry articles containing foam rubber
or similarly textured rubber-like materials.
Keep the area around the exhaust opening and adjacent
surrounding areas free from the accumulation of lint, dust,
and dirt.
The interior of the dryer and exhaust vent should be
cleaned periodically by qualied service personnel.
Do not install or store the dryer where it will be
exposed to the weather.
Always check the inside of the dryer for
foreign objects.
Clean the lint lter before or after each load.
Do not store plastic, paper, or clothing that may burn
or melt on top of the dryer during operation.
WARNING: This product contains chemicals known to
the State of California to cause cancer and birth defects
or other reproductive harm. Wash hands after handling.
BASIC SAFETY PRECAUTIONS
WARNING:
WARNING:
Toreducetheriskofre,electricshock,orinjurytopersonswhenusingthisappliance,
follow basic precautions, including the following:
5
•Properly ground dryer to conform with all governing
codes and ordinances. Follow details in the installation
instructions. Electrical shock can result if the dryer is not
properly grounded.
•Before use, the dryer must be properly installed as
described in this manual. Electrical shock can result if
the dryer is not properly grounded.
•Install and store the dryer where it will not be exposed
to temperatures below freezing or exposed to
the weather.
•All repairs and servicing must be performed by an
authorizedservicetechnicianunlessspecically
recommended in this Owner’s Guide. Use only
authorized factory parts. Failure to follow this warning
can cause serious injury, re, electrical shock, or death.
•To reduce the risk of electrical shock, do not install the
dryer in humid spaces. Failure to follow this warning
can cause serious injury, re, electrical shock, or death.
•Connect to a properly rated, protected, and sized
power circuit to avoid electrical overload. Improper
power circuits can melt, creating risk of electrical shock
and/or re hazard.
•Gas dryers MUST be exhausted to the outside. Failure
to follow these instructions can result in re or death.
•The dryer exhaust system must be exhausted to the
outside of the dwelling. If the dryer is not exhausted
outdoors,somenelintandlargeamountsof
moisture will be expelled into the laundry area. An
accumulation of lint in any area of the home can
create a health and re hazard.
•Useonlyrigidmetalorexiblemetal4inchdiameter
duct inside the dryer cabinet or for exhausting to the
outside. Use of plastic or other combustible ductwork
cancauseare.Puncturedductworkcancauseare
if it collapses or becomes otherwise restricted in use or
during installation.
•Ductwork is not provided with the dryer, and you
should obtain the necessary ductwork locally. The end
cap should have hinged dampers to prevent backdraft
when the dryer is not in use. Failure to follow these
instructions can result in re or death.
•Remove all packing items and dispose of all shipping
materials properly. Failure to do so can result in death,
re, explosion, burns, or death.
•Placedryeratleast18inchesabovetheoorfora
garage installation. Failure to do so can result in re,
explosion, burns, or death.
•Keep all packaging from children. Packaging material
can be dangerous for children. There is a risk of
suocation.
•Do not install near items that produce heat or open
ame such as stoves or cooking ovens. Failure to follow
this warning can cause product deformation, smoke and
re.
•Do not place candles, smoking materials, or other
ammablesontopoftheproduct.Dripping wax,
smoke, or re can result.
•Removeallprotectivevinyllmfromtheproduct.
Failure to do so can cause product damage, smoke or
re.
•Theexhaustductmustbe4inches(10.2cm)in
diameter with no obstructions. The exhaust duct
should be kept as short as possible. Make sure to
clean any old ducts before installing your new dryer.
Failure to follow these instructions can result in re or
death.
•Rigid or semi rigid metal ducting is recommended
for use between the dryer and the wall. In special
installations when it is impossible to make a
connection with the above recommendations, a UL
listedexiblemetaltransitionductmaybeused
between the dryer and wall connection only. The
useofthisductingwillaectdryingtime. Failure to
follow these instructions can result in re or death.
•DO NOT use sheet metal screws or other fasteners
which extend into the duct that could catch lint and
reducetheeciencyoftheexhaustsystem. Secure
all joints with duct tape. For complete details, follow
the Installation Instructions. Failure to follow these
instructions can result in re or death.
IMPORTANT SAFETY INSTRUCTIONS
SAFETY INSTRUCTIONS FOR INSTALLATION
Exhaust/Ducting:
WARNING:
Toreducetheriskofre,electricshock,orinjurytopersonswhenusingthisappliance,
follow basic precautions, including the following:
6
SAFETY INSTRUCTIONS FOR CONNECTING ELECTRICITY
WARNING:
Toreducetheriskofre,electricshock,orinjurytopersonswhenusingthisappliance,
follow basic precautions, including the following:
•Do not, under any circumstances, cut or remove
the ground prong from the power cord. To prevent
personal injury or damage to the dryer, the electrical
power cord must be plugged into a properly
grounded outlet.
•For personal safety, this dryer must be properly
grounded. Failure to do so can result in electrical
shock or injury.
•Refer to the installation instructions in this manual
forspecicelectricalrequirementsforyourmodel.
Failure to follow these instructions can create an
electrical shock hazard and/or a re hazard.
•This dryer must be plugged into a properly grounded
outlet. Electrical shock can result if the dryer is not
properly grounded. Have the wall outlet and circuit
checkedbyaqualiedelectriciantomakesurethe
outlet is properly grounded. Failure to follow these
instructions can create an electrical shock hazard
and/or a re hazard.
•The dryer should always be plugged into its own
individual electrical outlet which has a voltage rating
that matches the rating plate. This provides the best
performance and also prevents overloading house
wiring circuits which could cause a re hazard from
overheated wires.
•Never unplug your dryer by pulling on the power
cord.Alwaysgriptheplugrmlyandpullstraight
out from the outlet. The power cord can be damaged,
resulting in a risk of re and electrical shock.
•Repair or replace immediately all power cords that
have become frayed or otherwise damaged. Do not
use a cord that shows cracks or abrasion damage
along its length or at either end. The power cord can
melt, creating electrical shock and/or re hazard.
•When installing or moving the dryer, be careful not
to pinch, crush, or damage the power cord. This will
prevent injury and prevent damage to the dryer from
re and electrical shock.
IMPORTANT SAFETY INSTRUCTIONS
SAVE THESE INSTRUCTIONS
7
FEATURES AND BENEFITS
KEY PARTS AND COMPONENTS
EASY-TO-USE CONTROL PANEL
Select the desired dry cycle, add cycle options or
adjust settings with the touch of a button.
TIME AND STATUS DISPLAY
The easy-to-read LED display shows cycle status and
estimated time remaining.
CYCLE MODIFIERS
Adjust the cycle defaults such as temperature and dry
level with the touch of a button.
NOTE: Not all settings are available for all cycles.
CHECK VENT
(Duct Blockage Sensing System)
The CHECK VENT (Duct blockage sensing system)
detects and alerts you to blockages in the exhaust
system that reduce airflow from the dryer.
Maintaining clean exhaust system ducts improves
operating efficiency and helps minimize service calls,
saving you money.
LARGE CAPACITY STEEL DRUM WITH DRUM LIGHT
The ultra-large, oxidation-resistant, coated steel drum
offers superior durability. The light comes on when the
door is opened.
EASY-ACCESS REVERSIBLE DOOR
The wide-opening, see-through glass door provides
easy access for loading and unloading. Door swing
can be reversed to adjust for installation location.
FRONT-MOUNT LINT FILTER
The front-mount lint filter allows for easy access and
cleaning between loads.
LEVELING FEET
Four leveling feet (two in front, and two in back)
adjust to improve dryer stability on uneven floors.
There are several important components that are
referenced in this manual.
A
B
C
D
E
F
G
H
Rear of Dryer
Terminal
block
access panel
(Electric
models)
Gas
connection
location
(Gas models)
Power cord
location
(Gas
models)
Exhaust
duct
outlet
Water Inlet
Valve
ACCESSORIES
H
G
A D B
E
F
C
Included accessories Optional accessories
Y connector Hose
Side vent kit
(sold separately)
Kit No.
17025
Use the side vent kit for venting
directly to either side or to the
bottom. Gas dryers can not be
vented to the right.
8
INSTALLATION INSTRUCTIONS
KEY DIMENSIONS AND SPECIFICATIONS
CHOOSE THE PROPER LOCATION
A location that allows for proper exhaust installation.
A gas dryer must be exhausted to the outdoors. See
Venting the Dryer.
A grounded electrical outlet located within 2 ft. (61
cm) of either side of the dryer. See Connecting Electric
Dryers.
A sturdy oor to support the total dryer weight of 200
lbs (90.7 kg). The combined weight of a companion
appliance should also be considered.
No other fuel-burning appliance can be installed in the
same closet as a dryer.
Store and install the dryer where it will not be exposed
to temperatures below freezing or exposed to outdoor
weather conditions.
Choose a location with a solid, level oor with a
maximum slope of 1 inch (2.5 cm) under the entire
dryer. If the slope is greater than 1 inch (2.5 cm), install
the Extended Dryer Feet Kit. Clothes may not tumble
properly, and automatic sensor cycles may not operate
correctly if the dryer is not level.
Description Dryer Steam Dryer (Gas and Electric)
Electrical Requirements Refer to the rating label
Gas Requirements* NG: 4–10.5 inches WC
Gas Requirements* LP: 8–13 inches WC
Dimensions 27 in. (W) X 28 15/16 in. (D) X 40 13/16 in. (H), 50
¼
in. (D with door open)
68.6 cm (W) X 73.4 cm (D) X 104 cm (H), 127.5 cm (D with door open)
Net Weight Electric : 131.3 lb. (59.6 kg) Gas : 134 lb. (60.8 kg)
Drying Capacity IEC 7.3 cu.ft. (22.5 lb/10.2 kg)
*Gas Models Only
If the dryer is being installed in a garage, place the
dryer at least 18 inches (45.7cm) above the oor. If
using a pedestal, you will need 18 inches (46 cm) to
the bottom of the dryer.
To reduce the risk of electric shock, do not install the
dryer in damp or wet locations.
Do not operate your dryer at temperatures below 45°F
(7°C). At lower temperatures, the dryer might not shut
o at the end of an automatic cycle. This can result
in longer drying times. The dryer must not be installed
or stored in an area where it will be exposed to water
and/or weather. Check code requirements. Some
codes limit, or do not permit, installation of the dryer
in garages, closets, mobile homes or sleeping quarters.
Contact your local building inspector.
NOTE: Installing the dryer in a humid space, or
installing or storing the dryer where it will be exposed
to the weather or freezing temperatures, may result in
rust or other damage that is not covered by the product
warranty.
IMPORTANT: If you are installing your dryer in a
manufactured or mobile home, please refer to the
Special Electrical Requirements for Mobile or
Manufactured Homes section.
LOCATION REQUIREMENTS
IMPORTANT: Read all installation instructions completely before installing and operating your dryer.
It is important that you review this entire manual before installing and using your dryer. It contains detailed
instructions concerning electrical connections, gas connections and exhaust requirements.
CLEARANCES
Most installations require a minimum 5 ½ inch (14 cm)
clearance behind the dryer for the exhaust ducting.
Allow minimum clearances of at least 1 inch (2.5 cm)
on the sides and back to minimize vibration and noise.
Allowing additional clearance for installation and
servicing is recommended.
Be sure to allow for wall, door, or oor moldings that
may increase the required clearances.
Allow at least 21 inches (53.3 cm) in front of the dryer
to open the door.
9
Additional instructions for closet installations:
The closet door must allow for sufficient airflow. Refer
to the diagram above for minimum vent opening
requirements. A louvered door is also acceptable.
Closet Door Vent Requirements
(7.6 cm)
(7.6 cm)
(2.54 cm) (2.54 cm)(68.6 cm)
14
"
max.*
(35.6
cm)
21
1
/
4
"
(54 cm)
28
15
/
16
"
(73.4 cm)
50
1
/
4
"
(127.5 cm)
5"**
(12.7 cm)
40
13
/
16
"
(104 cm)
INSTALLATION INSTRUCTIONS
CLEARANCES (continued)
Recommended installation spacing for cabinet installation:
For cabinet installation with a door, minimum ventilation
openings in the top of the cabinet are required.
*Required spacing
**For side or bottom venting,
2 inches (5.1 cm) spacing is allowed.
28
(73.4 cm)
7"* (17.8 cm)
7"* (17.8 cm)
5"*
(12.7 cm)
1"*
(2.5 cm)
(68.6 cm)
1"
(2.54 cm)
1"
(2.54 cm)
27
"
10
INSTALLATION INSTRUCTIONS
GAS DRYERS
GASREQUIREMENTS(GASMODELSONlY)
To reduce the risk of re,
electric shock, or injury to persons when using this
appliance, follow basic precautions, including
the following:
WARNING:
•Gassupplyrequirements:Asshippedfromthe
factory,thisdryerisconguredforusewithnatural
gas(NG).Itcanbeconvertedforusewithpropane
(LP)gas.Gaspressuremustnotexceed8inches
watercolumnfor(NG),or13incheswatercolumnfor
(LP).
•Aqualiedserviceorgascompanytechnicianmust
connect the dryer to the gas service. Failure to follow
these instructions can result in re, explosion, or death.
•Isolate the dryer from the gas supply system by
closingitsindividualmanualshutovalveduringany
pressure testing of the gas supply. Failure to do so can
result in re, explosion, or death.
•Supplylinerequirements:Yourlaundryroommust
have a rigid gas supply line to your dryer. In the
UnitedStates,anindividualmanualshutovalve
MUSTbeinstalledwithinatleast6ft.(1.8m)ofthe
dryer, in accordance with the National Fuel Gas Code
ANSI Z223.1 or Canadian gas installation code CSA
B149.1.A⅛inchNPTpipeplugmustbeinstalled.
Failure to do so can result in re, explosion, or death.
•If using a rigid pipe, the rigid pipe should be ½ inch
IPS. If acceptable under local codes and ordinances
andwhenacceptabletoyourgassupplier,⅜inch
approved tubing may be used where lengths are less
than20ft.(6.1m).Largertubingshouldbeusedfor
lengthsinexcessof20ft.(6.1m). Failure to do so can
result in re, explosion, or death.
ELECTRICAL REQUIREMENTS FOR
GAS MODELS ONLY
•Do not, under any circumstances, cut or remove the
third(ground)prongfromthepowercord. Failure
to follow this warning can result in re, explosion, or
death.
•For personal safety, this dryer must be properly
grounded. Failure to follow this warning can result in
re, explosion, or death.
•Thepowercordofthisdryerisequippedwith
a3-prong(grounding)plugwhichmateswitha
standard3-prong(grounding)walloutlettominimize
the possibility of electric shock hazard from this
appliance. Failure to follow this warning can result in
re, explosion, or death.
•This dryer must be plugged into a 120-VAC, 60-Hz.
grounded outlet protected by a 15-ampere fuse or
circuit breaker. Failure to follow this warning can result
in re, explosion, or death.
•Where a standard 2-prong wall outlet is encountered,
it is your personal responsibility and obligation to
have it replaced with a properly grounded 3-prong
wall outlet. Failure to follow this warning can result in
re, explosion, or death.
•Connect the dryer to the type of gas shown on
the nameplate. Failure to do so can result in re,
explosion, or death.
•To prevent contamination of the gas valve, purge the
gas supply of air and sediment before connecting
the gas supply to the dryer. Before tightening the
connection between the gas supply and the dryer,
purge remaining air until the odor of gas is detected.
Failure to do so can result in re, explosion, or death.
•DONOTuseanopenametoinspectforgasleaks.
Useanoncorrosiveleakdetectionuid.Failure to do
so can result in re, explosion, or death.
•UseonlyanewAGA-orCSA-certiedgassupply
linewithexiblestainlesssteelconnectors. Failure to
do so can result in re, explosion, or death.
•Securely tighten all gas connections. Failure to do so
can result in re, explosion, or death.
•UseTeontapeorapipe-jointcompoundthatis
insolubleinpropane(LP)gasonallpipethreads.
Failure to do so can result in re, explosion,
or death.
•DO NOT attempt any disassembly of the dryer;
disassemblyrequirestheattentionandtoolsof
anauthorizedandqualiedservicetechnicianor
company. Failure to follow this warning can result in re,
explosion, or death.
3-prong
grounding
plug
3-prong
grounding
type wall
receptacle
Ensure proper
ground exists
before use.
11
To reduce the risk of re,
electric shock, or injury to persons when using this
appliance, follow basic precautions, including
the following:
•Installation and service must be performed by a
qualiedinstaller,serviceagency,orthegassupplier.
Failure to do so can result in re, explosion, or death.
•Useonlyanewstainlesssteelexibleconnectorand
anewAGA-certiedconnector.Failure to do so can
result in re, explosion, or death.
•Agasshutovalvemustbeinstalledwithin6ft.
(1.8m)ofthedryer. Failure to do so can result in re,
explosion, or death.
•Thedryerisconguredfornaturalgaswhen
shipped from the factory. Make sure that the dryer
isequippedwiththecorrectburnernozzleforthe
typeofgasbeingused(naturalgasorpropanegas).
Failure to do so can result in re, explosion, or death.
CONNECTING THE GAS SUPPLY
NOTE: This dryer is congured from the factory set for
natural gas (NG). If dryer is to be used with propane
(LP) gas, it must be converted by a qualied
service technician.
Make sure that the gas supply to the laundry room is
turned OFF and the dryer is unplugged. Conrm that
the type of gas available in your laundry room is
appropriate for the dryer.
Remove the shipping cap from the gas tting at the
back of the dryer. Be careful not to damage the
threads of the gas connector when removing the
shipping cap.
Connect the dryer to your laundry rooms gas supply
using a new exible stainless steel connector with a ⅜
inches NPT tting.
NOTE: DO NOT use old connectors.
Securely tighten all connections between the dryer
and your laundry rooms gas supply.
Turn on your laundry rooms gas supply.
Check all pipe connections (both internal and external)
for gas leaks with a noncorrosive leak-detection uid.
Proceed to Venting the Dryer (refer to pages 14-15).

The BTU rating of this dryer is AGA-certied for
elevations below 10,000 feet.
If your gas dryer is being installed at an elevation
above 10,000 feet, it must be derated by a qualied
technician or gas supplier.
•Ifnecessary,thecorrectnozzle(fortheLPnozzle
kit,orderpartnumber17025)shouldbeinstalled
byaqualiedtechnicianandthechangeshouldbe
noted on the dryer. Failure to do so can result in re,
explosion, or death.
•All connections must be in accordance with local
codes and regulations. Failure to do so can result in
re, explosion, or death.
•Gas dryers MUST exhaust to the outdoors. Failure to do
so can result in re, explosion, or death.
WARNING:
1
2
3
4
5
6
7
GASDRYERS(continued)
INSTALLATION INSTRUCTIONS
3/8" NPT Gas
Connection
Gas Supply
Shutoff Valve
AGA/CSA-Certified
Stainless Steel
Flexible Connector
1/8" NPT Pipe Plug
12
INSTALLATION INSTRUCTIONS
ELECTRIC DRYERS
ELECTRICAL REQUIREMENTS
To help prevent re,
electrical shock, serious injury, or death, the wiring
and grounding must conform to the latest edition of
the National Electrical Code, ANSI/NFPA 70 and all
applicable local regulations. Please contact a qualified
electrician to check your homes wiring and fuses to
ensure that your home has adequate electrical power to
operate the dryer.
To reduce the risk of
re, electric shock, or injury to persons when using this
appliance, follow basic precautions, including
the following:
Any installation in a manufactured or mobile
home must comply with the Manufactured Home
Construction and Safety Standards Title 24 CFR, Part
32-80 or Standard CAN/CSA0Z240 MH and local
codes and ordinances.
A 4-wire connection is require
d for all mobile and
manufactured home installations, as well as all new
construction after January 1, 1996. Failure to do so
can result in re, explosion, or death.
A gas dryer must be permanently attached to the floor.
To reduce the risk of combustion and re, the dryer
must be vented to the outside.
DO NOT vent the dryer under a manufactured home or
mobile home.
Electric dryers may be vented to the outside using the
back, left, right, or bottom panel.
Gas dryers may be vented to the outside using the
back, left, or bottom panel. Gas dryers may not be
vented to the outside using the right side panel because
of the burner housing.
The dryer exhaust duct must be affixed securely to
the manufactured or mobile home structure, and the
exhaust duct must be made of a material that will resist
re and c
ombustion. It is recommended that you use a
rigid or flexible metal duct.
DO NOT connect the dryer exhaust duct to any other
duct, vent, chimney, or other exhaust duct.
Make sure the dryer has adequate access to outside
fresh air to ensure proper operation. The opening for
outside fresh air must be at least 25 in
2
(163 cm
2
).
It is important that the clearance of the duct from any
combustible construction be at least 2 inches (5 cm),
and when venting the dryer to the outdoors, the dryer
can be installed with a clearance of 1 inch (2.5 cm) at
the sides and back of the dryer.
Please be aware that venting materials are not supplied
with the dryer. You should obtain the venting materials
necessary for pr
oper installation.
This dryer must be connected to a grounded metal,
permanent wiring system, or an equipment grounding
conductor must be run with the circuit conductors and
connected to the equipment grounding terminal or
lead on the dryer. Failure to do so can result in fire,
explosion, or death.
The dryer has its own terminal block that must be
connected to a separate 230 VAC, 60-Hertz, single
phase circuit, fused at 30 amperes (the circuit must be
fused on both sides of the line). ELECTRICAL SERVICE
FOR THE DRYER SHOULD BE OF THE MAXIMUM
RATE VOLTAGE LISTED ON THE NAMEPLATE. DO
NOT CONNECT DRYER TO 110-, 115-, OR 120-VOLT
CIRCUIT. Failure to follow these instructions can result
in fire, explosion, or death.
If branch circuit to dryer is 15 ft. (4.5 m) or less in
length, use UL (Underwriters Laboratories) listed No.-
10 AWG wire (copper wire only), or as required by
local codes. If over 15 ft. (4.50 m), use UL-listed No.-8
AWG wire (copper wire only), or as required by local
codes. Allow sufficient slack in wiring so dryer can
be moved from its normal location when necessary.
Failure to do so can result in fire, explosion, or death.
The po
wer cord (pigtail) connection between wall
receptacle and dryer terminal block IS NOT supplied
with the dryer. Type of pigtail and gauge of wire
must conform to local codes and with instructions on
the following pages. Failure to follow these instructions
can result in fire, explosion, or death
A 4-wire connection is required for all new
construction after January 1, 1996. A 4-wire
connection must be used where local codes do not
permit grounding through the neutral wire. Failure to
do so can result in fire, explosion, or death.
To reduce the risk of re,
electric shock, or injury to persons when using this
appliance, follow basic precautions, including the
following:
WARNING:
WARNING:
WARNING:
Special Electrical Requirements for Mobile
or Manufactured Homes
Electrical Requirements for Electric Models Only
13
ELECTRIC DRYERS (continued)
CONNECTING ELECTRIC DRYERS (USA Only)
Connect the power cord to the terminal block. Each
colored wire should be connected to the terminal block
screw with the same color wire around it. For example,
connect the black power cord wire to the terminal block
screw with the black wire around it. Failure to follow
these instructions may result in a short or overload.
Four-Wire Power Cord
A 4-wire connection is required for all
mobile and manufactured home installations,
as well as all new construction after
January 1, 1996.
A UL-listed strain relief is required.
Use a 30-amp, 240-volt, 4-wire, UL-listed power cord
with #10 AWG-minimum copper conductor and closed
loop or forked terminals with upturned ends.
Remove the terminal block access cover on th
e upper
back of the dryer.
Install a UL-listed strain relief into the power cord
through-hole.
Thread a 30-amp, 240-volt, 4-wire, UL-listed power
cord with #10 AWG-minimum copper conductor
through the strain relief.
Transfer the dryers ground wire from behind the green
ground screw to the center screw of the terminal block.
Attach the two hot leads of the power cord to the outer
terminal block screws.
Attach the white neutral wire to the center screw of
the terminal block.
Attach the power cord ground wire to the green
ground screw.
TIGHTEN ALL SCREWS SECURELY.
Reinstall the terminal block access cover.
Attach the two hot leads (black and red) of the
power cord to the outer terminal block screws.
Attach the neutral (white) wire to the center terminal
block screw.
Connect the external ground (if required by local
codes) to the green ground screw.
TIGHTEN ALL SCREWS SECURELY.
Reinstall the terminal block access cover.
Grounding through the neutral conductor is prohibited
for: (1) new branch-circuit installations, (2) mobile
homes, (3) recreational vehicles, and (4) areas where
local codes prohibit grounding through the
neutral conductor.
Three-Wire Power Cord
A 3-wire connection is NOT permitted on
new construction after January 1, 1996.
• A UL-listed strain relief is required.
Use a 30-amp, 240-volt, 3-wire, UL-listed power cord
with #10 AWG-minimum copper conductor and closed
loop or forked terminals with upturned ends.
Remove the terminal block access cover on the upper
back of the dryer.
Install a UL-listed strain relief into the power cord
through-hole.
Thread a 30-amp, 240-volt, 3-wire, UL-li
sted power
cord with #10 AWG-minimum copper conductor
through the strain relief.
WARNING:
1
4 4
2
5
5
3
6
7
8
9
6
7
8
3
2
1
UL-Listed
Strain Relief
UL-Listed 4-Wire
Power Cord
Terminal
Block
UL-Listed
Strain Relief
UL-Listed 3-Wire
Power Cord
Terminal
Block
Power Cord
Ground Wire
White wire moved
from ground screw
Ground Screw
Hot (Red)
Neutral
(White)
Hot
(Black)
White wire from
dryer harness
Ground Screw
Hot (Red)
Neutral
(White)
Hot
(Black)
INSTALLATION INSTRUCTIONS
14
VENTING THE DRYER
CHECK YOUR EXHAUST SYSTEM FOR PROBLEMS
IMPORTANT!
The most common cause of dryer problems is poor exhaust venting. Before installing your new dryer, check the
items listed below to make sure you get the best possible performance. This can save you time and money by
reducing cycle times and increasing energy eciency.
•DIRTY OR DAMAGED EXHAUST DUCTS. Lint builds up in exhaust ducts over time. This decreases the airow and
makes the dryer work harder. Visually inspect your ducts from both ends and have them cleaned if they have not
been cleaned recently.
•WRONG VENT MATERIAL. Check your vent to make sure it is rigid or semi-rigid metal ducting. If your venting is
plastic or exible foil, have it replaced before using the dryer.
•RESTRICTED OR DAMAGED VENT HOOD. Check your vent hood outside. It must be clean and free of lint buildup.
Check the damper and make sure it opens fully and easily.
•EXCESSIVELY LONG VENT. Measure the length of your exhaust system and count the elbows. Use the chart below
to see if your duct is too long. If it is too long, have the duct routed to another location that is within the
venting guidelines.
•DO NOT USE PLASTIC OR FOIL VENTING. The transition duct from your dryer to the wall must be rigid or
semi-rigid metal ducting. If your old transition duct is plastic or foil, REPLACE IT with semi-rigid metal ducting.

Find your vent hood type in the chart below.
Select the row that matches the number of elbows in your dryer duct run.
Look to the right of the elbow number for the maximum duct length for your installation. Longer duct length will result
in reduced drying performance, longer dry times and increased energy consumption. Extremely long ducts can even
shorten the life of the dryer.
DO NOT exceed the maximum length for the vent hood type and number of elbows used.
DUCT LENGTH CHART
NOTE: Deduct 6 ft. (1.8 m) for each additional elbow. Using more than four 90° elbows is not recommended.
1
2
3
Recommended
Only for Short-Run Installations
4"
(10.2 cm )
4"
(10.2 cm )
(6.35 cm )
Number of 90°
Elbows
Vent Hood Type
Maximum length of 4" (10.2 cm )
diameter rigid metal duct
65 feet (19.8 m)
55 feet (16.8 m)
47 feet (13.7 m)
36 feet (11.0 m)
28 feet (8.5 m)
55 feet (16.8 m)
47 feet (13.7 m)
41 feet (12.5 m)
30 feet (9.1 m)
22 feet (6.7 m)
0
1
2
3
4
0
1
2
3
4
(2.5)
INSTALLATION INSTRUCTIONS
15
VENTINGTHEDRYER(continued)

Follow the guidelines below to maximize dryer
performance and reduce lint buildup and condensation
in the ductwork.
NOTE: Transition duct and ttings are NOT included
and must be purchased separately.
Use 4 inch (102mm) diameter rigid or semi-rigid
metal duct.
The exhaust duct run should be as short as possible.
Use as few elbow joints as possible.
The male end of each section of exhaust duct must
point away from the dryer.
Use duct tape on all joints. Never use screws.
Insulate ducts that runs through unheated areas in
order to reduce condensation and lint buildup on
duct surfaces.
The total length of semi-rigid metal transition duct
should not exceed 8 ft. (2.4 m).
IMPORTANT: Failure to exhaust the dryer, per the
guidelines included within these instructions, may
result in unsatisfactory dryer performance. All venting
and ductwork beyond the exterior of the dryer is the
responsibility of the consumer. Product failure, as
a result of improper venting, is not covered by the
manufacturer’s warranty.

Verify all ducts and elbows are clean and free
from any blockages.
Measure duct length. DO NOT exceed the
maximum length listed in the Duct Length Chart.
Connect dryer exhaust to existing duct.
Failure to follow these
guidelines will result in poor performance, product
failure, and/or result in re or death.
WARNING:
1
2
3
Only use duct tape or clamps.
DO NOT use screws to secure ductwork.
Use rigid or semi-rigid metal ducts.
DO NOT use plastic or thin metal foil tubing
for ductwork.
The male end of each elbow must always point in
the direction of the airow.
Male
Ends
Correct Venting
Incorrect Venting
NOTE: Be careful when moving the dryer into its
nal location. Do NOT crush the duct. Make sure the
connections do not come loose.
INSTALLATION INSTRUCTIONS
16
CONNECTING THE INLET HOSE
The dryer must be connected to the cold water tap
using the new water supply hose. Do not use old hoses.
NOTE:
Water supply pressure must be between 20 psi and
120 psi (138–827 kPa).
• Do not strip or cross-thread when connecting inlet hose
to the valve.
If the water supply pressure is more than 120 psi (827 kPa),
a pressure reducing valve should be installed.
Periodically check the condition of the hose and
replace the hose if necessary.
Replace inlet hoses after 5 years of use to reduce the
risk of hose failure.
Record hose installation or replacement dates on the
hoses for future reference.
1. Check the rubber seal in the inlet hose. Two rubber
seals are supplied with each inlet hose. They are used
for preventing water leaks. Make sure the connection
to the cold water tap is tight.
2. Check the installation type.
Connect all water supply hoses tightly by hand and
then tighten another 2/3 turn with pliers.
WITH WASHER: When connecting the dryer to the same
faucet as a washer.
hose.
b. Connect the short hose to the Y-connector.
c. Connect the other end of the short hose to the cold
water faucet.
d. Connect the long dryer hose to one side of the Y-connector
and connect the washer hose to the other side.
WITHOUT WASHER: If the dryer does not share the
cold water tap with a washer.
a. Connect the straight end of the long hose to the cold
water faucet.
INSTALLATION INSTRUCTIONS
NOTE:
several gallons of water into a drain or bucket. This
will help prevent foreign particles such as sand and
scale from cloggong the dryer inlet valve.
• Do not overtighten. Damage to the coupling can
result.
3. Connect the hose to the dryer.
Connect the water supply hose to the dryer inlet
valve tightly by hand and then tighten another 2/3
turn with pliers. Make sure that there are no kinks in
the hoses and that they are not crushed.
4. Turn on the cold water faucet.
5. Check for leaks at the Y-connector (if used) and all
hoses.
NOTE:
• If any leaks are found, shut o
the water faucet,
remove the hose and check the condition of the hose
washer.
Hose
connector
Y connector
Rubber
seal
Long
hose
WITH WASHER WITHOUT WASHER
Short
hose
Y connector
17
LEVELING THE DRYER
• To reduce the risk of injury to persons, adhere to all
industry recommended safety procedures including
the use of long sleeved gloves and safety glasses.
Failure to follow this warning can cause serious injury
or death.
• The appliances are heavy. Two or more people are
required when installing the dryer. Failure to follow
this warning can cause serious injury or death.
To ensure that the dryer provides optimal drying
performance, it must be level. To minimize vibration,
noise, and unwanted movement, the oor must be a
level, solid surface.
NOTE: Adjust the leveling feet only as far as necessary
to level the dryer. Extending the leveling feet more than
necessary can cause the dryer to vibrate.
WARNING:
Level
Leveling Feet
Position the dryer in the nal location. Place a level
across the top of the dryer.
All four leveling feet must rest solidly on the oor.
Gently push on the top corners of the dryer to make
sure that the dryer does not rock from corner to corner.
1
Use a wrench to turn the leveling feet. Turn the
leveling foot clockwise to raise the dryer; turn the
foot counterclockwise to lower the dryer. Using a
level, adjust the feet until the dryer is level from side
to side and front to back. Make sure all four feet
are in rm contact with the oor.
NOTE: If you are installing the dryer on the optional
pedestal, the dryer leveling feet should be fully retracted.
Use the leveling feet on the pedestal to level the dryer.
2
INSTALLATION INSTRUCTIONS
18
Hole cap
Hinge Screw
Hinge
assembly
Cover cap
Swing Door
inner door
frame
latch hook
INSTALLATION INSTRUCTIONSINSTALLATION INSTRUCTIONS
REVERSING THE DOOR SWING
WARNING:
THE DRYER DOOR IS VERY LARGE AND HEAVY. Failure to follow the instructions below can result in damage to
the dryer, property damage or personal injury.
Open the door and remove the two plastic hole
caps on the catch side by gently prying up with a
at blade screwdriver. Save these for step 6.
CAUTION: Be sure to support the weight of the
door before removing the hinge screws.
While supporting the door, remove the four
screws, two from each hinge. Set the door aside
face down on a protected surface to prevent
damage to the door or the work surface.
With the door on a protected surface, remove the
12 screws on each side of the door and lift o the
inner door frame using a at blade screwdriver.
Remove the latch hook and blank and move them
to the opposite side.
Remove the four screws securing the hinges to the
door frame. Remove the two plastic cover caps on
the side opposite the hinges. Reinstall the hinges
and cover caps on the opposite sides from which
they were removed.
With the hinges and cover caps in the new
locations, remount the inner door frame onto the
outer door frame with the screws removed in step
3.
Reinstall the door with the screws from step 2, and
snap the hole caps into the open hinge mounting holes.
Test the swing of the door to make sure the hinges
and latch are properly aligned and that the door
closes and latches correctly.
1
2
3
4
5
6
7
Swing Door
19
INSTALLATION INSTRUCTIONS
FINAL INSTALLATION CHECK
Once you have completed the installation of the dryer
and it is in its nal location, conrm proper operation
with the following steps and tests.
Is gas turned on? (Gas models only)
Is dryer plugged in? Dryer should always be
plugged into the proper outlet.
Gas dryer should use a
120-VAC, 60-Hz. grounded
3-prong outlet.
Electric dryer should use a
4-wire connection which is
required for all mobile
and manufactured home
installations, as well as all
new construction after
January 1, 1996.
-- OR --
A 3-wire connection.
NOTE: A 3-wire connection
is NOT permitted on new
construction after
January 1, 1996.
Is the dryer transition duct connected? Make sure
the transition duct behind the dryer is properly
connected and is not crushed or damaged.
Is the dryer level? Once the dryer is in its nal location,
recheck the dryer to be sure it is level. Make sure it is
level front to back and side to side, and that all four
leveling feet rest rmly on the oor.
Is the dryer heating normally? Perform the following
dryer heating test.

GAS MODELS
Close the dryer door, press the POWER button to turn
the dryer on, and start the dryer on a heat setting. When
the dryer starts, the igniter should ignite the main burner.
NOTE: If all air is not purged from the gas line, the gas
igniter may turn o before the main burner ignites. If
this happens, the igniter will reattempt gas ignition until
all the air is purged from the gas line.
ELECTRIC MODELS
Close the dryer door, press the POWER button to turn
the dryer on, and start the dryer on a heat setting. The
exhaust air should be warm after the dryer has been
operating for 3 minutes.

Eective dryer operation requires proper airow. The
adequacy of the airow can be measured by evaluating
the static pressure. Static pressure in the exhaust duct
can be measured with a manometer, placed on the ex-
haust duct approximately 2 ft. (60.9 cm) from the dryer.
Static pressure in the exhaust duct should not exceed
0.6 inches (1.5 cm). The dryer should be checked while
the dryer is running with no load.

Once the dryer is in its nal location, recheck the dryer
to be sure it is level. Make sure it is level front to back
and side to side, and that all four leveling feet are
rmly on the oor.

The vent duct should be checked for lint buildup and
cleaned at least once per year. If any noticeable
reduction in drying performance occurs, check the duct
for obstructions and blockages.
1
2
3
4
5
INSTALLATION INSTRUCTIONS
20
HOW TO USE
POWER(ON/OFF)BUTTON
Press to turn the dryer ON. Press again to turn the
dryer OFF. Pressing the POWER button during a cycle
will cancel that cycle and any settings will be lost.
CYCLE BUTTONS
Press the CYCLE buttons repeatedly to scroll through
the cycle selections until the desired cycle is selected.
The standard presets for the selected cycle will be
shown in the display. On MANUAL DRY cycles, these
settings can be adjusted using the cycle setting
buttons anytime before starting the cycle.
START/PAUSE BUTTON
Press this button to START the selected cycle. If the
dryer is running, use this button to PAUSE the cycle
without losing the current settings.
NOTE: If the dryer has been stopped for more than
four minutes, the dryer will turn o automatically
and all settings will be lost.
OPTION BUTTONS
These buttons allow you to select cycle options.
Some of the option buttons have secondary
functions. The controls can be locked or unlocked by
pressing and holding the SAVE ENERGY+ button for
three seconds.
CYCLE MODIFIER BUTTONS
Use these buttons to adjust the settings for the
selected cycle. The settings light up above the
buttons to show the current selection. The default
temperature setting cannot be changed in AUTO
DRY cycles. AUTO DRY cycles are modied using
the Dry Level button.
TIME AND STATUS DISPLAY
The display shows the estimated time remaining for
auto cycles and actual time for timed cycles. The
status of the cycle is also displayed. The CHECK
VENT indicator will illuminate if there is a serious
restriction in the exhaust system.
MORE TIME/LESS TIME BUTTONS
Use these buttons with the TIMED DRY and other
MANUAL DRY cycles to adjust the drying time. Press
the MORE TIME button to increase the selected
manual cycle time by one minute; press LESS TIME
to decrease the cycle time by one minute.
CHECK VENT INDICATOR
(DUCTBLOCKAGESENSINGSYSTEM)
The CHECK VENT duct blockage sensing system
detects and alerts you to blockages in the ductwork
that reduce exhaust ow from the dryer. This light
does not indicate any problems with your dryer.
If this light blinks, it indicates that your homes
exhaust system has a serious restriction, which is not
covered by your dryer’s warranty. There are services
available for cleaning/maintaining the external
venting. Sears provides this service via Sears Carpet,
Upholstery, and Duct Cleaning. Call 1-800-661-6594
to schedule duct cleaning service from Sears (if it is
available in your area).
STEAM REFRESH CYCLE
The STEAM REFRESH cycle uses the power of steam
to quickly reduce wrinkles and odor in fabrics.
It also refreshes wrinkled clothes that have been
stored for an extended period of time, and it can
make heavily wrinkled clothes easier to iron. STEAM
REFRESH can also be used to help reduce odors in
fabrics.
F
B
C
WARNING:
Toreducetheriskofre,electricshock,orinjurytopersons,readthisentire
manual, including the Important Safety Instructions, before operating this dryer.
NOTE: To protect your fabrics, not all settings are
allowed in all cycles.
D
A
G
H
E
CONTROL PANEL FEATURES
A
D
D
C
G
H
B
E
F
I
I
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64
  • Page 65 65
  • Page 66 66
  • Page 67 67
  • Page 68 68
  • Page 69 69
  • Page 70 70
  • Page 71 71
  • Page 72 72

Kenmore 796.7142 Series Le manuel du propriétaire

Catégorie
Sèche-linge électriques
Taper
Le manuel du propriétaire
Ce manuel convient également à

dans d''autres langues