Marson MT8495 Mode d'emploi

Marque: Marson

Modèle: MT8495

Catégorie: Lecteurs de codes à barres

Taper: Mode d'emploi

2D Mini Barcode Scanner Quick Guide

P/N: 8012-0081000

2D Mini

Barcode Scanner

Quick Guide

FCC WARNING STATEMENT

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one of the following

measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

CANADIAN DOC STATEMENT

This digital apparatus does not exceed the Class B limits for radio noise for digital

apparatus set out in the Radio Interference Regulations of the Canadian Department of

Communications.

Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les

limites applicables aux appareils numériques de las classe B prescrites dans le

Réglement sur le brouillage radioélectrique édicté par les ministère des Communica-

tions du Canada.

CE MARKING AND EUROPEAN UNION COMPLIANCE

Testing for compliance to CE requirements was performed by an independent

laboratory. The unit under test was found compliant with all the applicable Directives,

2004/108/EC and 2006/95/EC.

WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT

The WEEE directive places an obligation on all EU-based manufacturers and

importers to take-back electronic products at the end of their useful life.

ROHS STATEMENT OF COMPLIANCE

This product is compliant to Directive 2002/95/EC.

RoHS

- 1 -

1. Take any metals into contact with the terminals in connectors.

2. Use the scanner where any inflammable gases.

If following condition occur, immediately power off the host computer,

disconnect the interface cable, and contact your nearest dealer.

1. Smoke, abnormal odors or noises come from the scanner.

2. Drop the scanner so as to affect the operation or damage its housing.

Do Not

Do not do behavior below.

1. Put the scanner in places excessively high temperatures such as expose

under direct sunlight.

2. Use the scanner in extremely humid area or drastic temperature

changes.

3. Place the scanner in oily smoke or steam environment such as cooking

range.

4. Be covered or wrapped up the scanner in bad-ventilated area such as

under cloth or blanket.

5. Insert or drop foreign materials or water into scanning window or vents.

6. Using the scanner while hand is wet or damp.

7. Use the scanner with anti-slip gloves containing plasticizer and

chemicals or organic solvents such as benzene, thinner, insecticide etc

to clean the housing. Otherwise, it could not result fire and electrical

shock but housing may be broken and injured.

8. Scratch or modify the scanner and bend, twist, pull or heat its interface

cable.

9. Put heavy objects on interface cable.

Do not stare the light source from the scanning window or do not point the

scanning window at other people’s eyes or eyesight may be damaged

by direct exposure under the light.

Do not put the scanner on an unstable or inclined plane.

The scanner may drop, creating injuries.

Once the interface cable is damaged such as exposed or broken copper

wires, stop using immediately and contact your dealer. Otherwise, it could

result fire or electrical shock.

WARNING AND CAUTION

- 2 -

OUT OF THE BOX

2D Mini Barcode Scanner

Quick Guide USB Extension Cable

Barcode Reader

2D Mini

Quick Guide

- 3 -

INTRODUCTION

SPECIFICATIONS

Trigger

Exit Window

USB Connector

Protective Cover

Light source White LED, Visible red LED

Scan rate 30 Frames/sec

Sensor 640 x 480

Resolution 5mil (1D) / 10mil (2D)

PCS 25%

Housing PC

Interface USB HID, USB VCP

Voltage 5 VDC ± 5%

Current < 220 mA(Working); < 95 mA(Standby)

Operating Temp 0 to 60˚C (32 to 140˚F)

Storage Temp -40 to 70˚C (-40 to 158˚F)

Symbologies All major 1D & 2D barcodes

- 4 -

GETTING STARTED

- 5 -

BEEPER INDICATION

Single beep Good read

Two beeps The scanner successfully reads

a configuration barcode

Four beeps Power up

- 6 -

INTERFACE

DEFAULT

CHECK

VERSION

GENERAL SETTINGS

USB VCP

To scan a barcode, make sure the aiming beam fully

covers the barcode.





USB HID

- 7 -

READING MODE

TRIGGER

CONTINUOUS

AUTO-SENSING

- 8 -

TERMINATOR

CR + LF

NONE

TAB

KEYBOARD LAYOUT

ENGLISH

(USA)

GERMAN

FRENCH

SPANISH

- 9 -

JAPANESE

ITALIAN

CZECH

HUNGARIAN

- 10 -

INVERSE BARCODE

SYMBOLOGIES BEEPER

ENABLE

ALL CODE

DISABLE

ALL CODE

ENABLE

- 11 -

CAPSLOCK

MUTE

- 12 -

DISABLE

UNMUTE

OFF

- 13 -

TEST BARCODES

EAN

Code 128

12345678

Code 39

CODE-39 TEST

Interleaved 2 of 5

9876543210

- 14 -

QR Code Micro QR Code

PDF417

Data Matrix Aztec

Marson MT8495 Mode d'emploi

Marque: Marson

Modèle: MT8495

Catégorie: Lecteurs de codes à barres

Taper: Mode d'emploi

Télécharger le PDF

rapport

dans d''autres langues

English: Marson MT8495 User guide

Marson MT8495 Mode d'emploi

Marson MT8495 Mode d'emploi

dans d''autres langues

Documents connexes

Autres documents