Kichler 300317DBK Manuel utilisateur

INSTRUCTION MANUAL

Product images may vary slightly from actual product.

52" Range LED

KICHLER.COM

TABLE OF CONTENTS

SAFETY RULES …………………………………………………………………………....4

TOOLS REQUIRED …………………………..………………………………..………...5

PACKAGE CONTENTS ……………….....................……………………………....5

MOUNTING OPTIONS ………….................................................................6

HANGING THE FAN ……………………………………………………………………...7

ELECTRICAL CONNECTIONS…………................................................10

FINISHING THE MOTOR INSTALLATION.....………..........................11

ATTACHING THE FAN BLADES ………………………….......................... 12

INSTALLING THE BLADE HOLDER ………………....…………...…………13

INSTALLING THE SWITCH HOUSING ………………………….............. 14

INSTALLING THE LIGHT KIT AND ACRYLIC SHADE…………..... 15

OPERATING INSTRUCTIONS …………………………...........……………... 16

TROUBLESHOOTING …………………………..................………………………18

FCC INFORMATION ............…………………………………………………..........19

52" Range LED | 3

4 | KICHLER.COM

SAFETY RULES

READ AND SAVE THESE INSTRUCTIONS

CAUTIONCAUTION – RISK OF SHOCK – Disconnect Power at – RISK OF SHOCK – Disconnect Power at

the main circuit breaker panel or main fuse box before the main circuit breaker panel or main fuse box before

starting and during the installation.starting and during the installation.

WARNING:WARNING: This fixture is intended for installation in This fixture is intended for installation in

accordance with the National Electrical Code (NEC) and accordance with the National Electrical Code (NEC) and

all local code specifications. If you are not familiar with all local code specifications. If you are not familiar with

code requirements, installation by a certified electrician is code requirements, installation by a certified electrician is

recommended.recommended.

WARING: WARING: To reduce the risk of fire or electric shock, use To reduce the risk of fire or electric shock, use

only the control provided with the fan.only the control provided with the fan.

WARNING: WARNING: To reduce the risk of fire, electric shock, or To reduce the risk of fire, electric shock, or

Personal Injury, mount directly to a structural framing Personal Injury, mount directly to a structural framing

member or to an outlet box marked “Acceptable For member or to an outlet box marked “Acceptable For

Fan Support of 15.9kg(35 lbs) or less”. For outlet box Fan Support of 15.9kg(35 lbs) or less”. For outlet box

mounting, use mounting screws provided with the outlet mounting, use mounting screws provided with the outlet

box.box.

WARNING:WARNING: Do not operate reversing switch while fan Do not operate reversing switch while fan

blades are in motion. Fan must be turned off and blades blades are in motion. Fan must be turned off and blades

stopped before reversing blade direction.stopped before reversing blade direction.

Avoid placing objects in the path of the blades.Avoid placing objects in the path of the blades.

To avoid personal injury or damage to the fan and other To avoid personal injury or damage to the fan and other

items, be cautions when working around or cleaning the items, be cautions when working around or cleaning the

fan.fan.

1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

11.

Make sure the installation site you choose allows a

minimum clearance of 7 feet from the blades to the floor

and at least 30 inches from the ends of the blades to any

obstruction.

Do not use water or detergents when cleaning the fan or

fan blades. A dry dust cloth or lightly dampened cloth will

be suitable for most cleaning.

After making the electrical connections, spliced

conductors should be turned upward and pushed carefully

up into outlet box. The wires should spread apart with the

ground wire and white(common) wire to one side with the

black (load) wire to the other side of the outlet box.

Electrical diagrams are for reference only. Light kits that

are not packed with fan must be ETL Listed and marked

suitable for use with the model fan you are installing.

Switches must be ETL General Use Switches. Refer to the

instructions packaged with the light kits and switches for

proper assembly.

WARNING

TO REDUCE THE RISK OF PERSONAL INJURY. DO

NOT BEND THE BLADE BRACKETS (ALSO REFERRED

TO AS FLANGES) DURING ASSEMBLY OR AFTER

INSTALLATION. DO NOT INSERT OBJECTS IN THE PATH

OF THE BLADES.

TOOLS REQUIRED

PACKAGE CONTENTS

Phillips screwdriver

Blade screwdriver

11 mm wrench

Step ladder

Wire cutters

Unpack your fan and check the contents . You should have the following items:

A. Mounting bracket

B. Ball / downrod assembly

C. Canopy

D. Canopy Hole Cover

E. Coupling Cover

F. Motor Body

G. Fan Blade (6)

H. Blade Holder (6)

I. Switch Housing

J. Light Kit

K . Acrylic Shade

L .Remote Control Kit:

Remote Control (1)

Receiver (1)

Battery (1)

Wire Connectors (6)

Handset Control Holder (1)

M. Package hardware

1) Mounting hardware :

Wire Connector (3)

2)Blade attachment hardware :

Screws(18)

3.) Blade Holder attachment

hardware: Screw (12 )

A

K

G

I

M

L

J

B

C

D

E

F

H

52" Range LED | 5

6 | KICHLER.COM

MOUNTING OPTIONS

If there isn’t an existing UL (cUL for Canadian Installation ) listed

mounting box, then read the following instructions. Disconnect the

power by removing fuses or turning o circuit breakers.

Secure the outlet box directly to the building structure. Use

appropriate fasteners and building materials. The outlet box and its

support must be able to fully support the full weight of the fan (up to

50 lbs). Do not use plastic outlet boxes.

Figure 1, 2 and 3 are examples of dierent ways to mount the outlet

box.

NOTE: NOTE: If you are installing the ceiling fan on a sloped (vaulted) ceiling,

you may need a longer downrod to maintain proper clearance

between the tip of the blade and the ceiling. A minimum clearance of

12” is suggested for optimal operation.

NOTE: NOTE: Depending on the location you have selected for installation,

you may need to purchase and install a “Joist Hanger” for the support

of the outlet box. Make sure the joist hanger you purchase has been

designed for use with ceiling fans. (Fig.4)

Outlet box

ANGLED CEILING

MAXIMUM 18° ANGLE Provide strong

support

Ceiling

mounting

plate

Recessed

Outlet box

Fig. 2

Fig. 4

Fig. 3

Fig. 1

Outlet box

HANGING THE FAN

REMEMBERREMEMBER to turn off the power before you begin installation. This is

necessary for your safety and also the proper programming of the control

system. To properly install your ceiling fan, follow the steps below.

Step 1.Step 1. Before attaching fan to outlet box (not included), ensure the outlet box

is securely fastened to at least two points to a structural ceiling member

(a loose box will cause the fan to wobble). Install the screws and washers

included with the outlet box. NOTE:NOTE: Do not lock the screws completely, just

lock half.

Pass the 120 volt supply wires form the ceiling outlet box through the center

of the ceiling mounting bracket.(Fig. 5)

Step 2. Step 2. Align the slot holes on the mounting bracket with the screws, and

push the mounting bracket to the screws, then tighten the screws. (Fig. 6

and 7)

Fig. 5

Fig. 6

Fig. 7

52" Range LED | 7

Outlet Box

Mounting Bracket

Washer

Screw

8 | KICHLER.COM

HANGING THE FAN

Step 3. Step 3. Remove the hairpin and clevis pin from the downrod assembly, retain

for later use.(Fig.8)

Step 4.Step 4. Loosen the two set screws on the motor coupling.(Fig. 9)

Step 5.Step 5. Place the coupling cover, canopy hole cover and canopy over the

coupling found on the top of the motor assembly. Carefully feed fan wires

from the motor assembly through the downrod, then insert the downrod into

the coupling.(Fig.10)

Fig. 10

Set Screw

Downrod

Canopy

Canopy Hole Cover

Coupling Cover

Coupling

Clevis Pin

Hair pin

Fig. 9

Fig. 8

52" Range LED | 9

HANGING THE FAN

Step 6.Step 6. Pass the clevis pin through the downrod and coupling found on the

motor assembly, and secure with the hair pin. Tighten set screws found on

the coupling. (Fig. 11 )

Step 7.Step 7. Now lift the motor body into position and place the hanger ball into

the mounting bracket. Rotate until the "Check Tab" has dropped into the

"Registration Slot" and seats firmly. (Fig. 12) The entire motor body should

not rotate if this is done correctly.

WARNING: WARNING: Failure to properly seat the "Check Tab" can damage the ceiling

fan during operation.

Fig. 12

Fig. 11

Hairpin

Clevis Pin

Set Screw

OK NO

Coupling

Registration Slot

Check Tab

10 | KICHLER.COM

MAKE THE ELECTRICAL CONNECTIONS

WARNING: WARNING: To avoid possible electrical shock, be sure you have turned off To avoid possible electrical shock, be sure you have turned off

the power at the main circuit panel before wiring. Follow the steps below the power at the main circuit panel before wiring. Follow the steps below

to connect the fan to your household wiring. Use the wire connecting nuts to connect the fan to your household wiring. Use the wire connecting nuts

supplied with your fan. Secure the connector with electrical tape. Make sure supplied with your fan. Secure the connector with electrical tape. Make sure

there are no loose wire stands or connections.there are no loose wire stands or connections.

WARNING: WARNING: If your house wires are different colors than referenced in this If your house wires are different colors than referenced in this

manual, stop immediately. A professional electrician is recommended to manual, stop immediately. A professional electrician is recommended to

determine proper wiring.determine proper wiring.

Step 1. Step 1. Insert the receiver into the mounting bracket, and keep flat in Insert the receiver into the mounting bracket, and keep flat in

opposition of ceiling. (Fig. 13)opposition of ceiling. (Fig. 13)

Step 2.Step 2. Motor to Receiver Electrical Connections: Connect the BLACK Motor to Receiver Electrical Connections: Connect the BLACK

wire from the fan to BLACK wire marked "TO MOTOR L" from the receiver. wire from the fan to BLACK wire marked "TO MOTOR L" from the receiver.

Connect the WHITE wire from the fan to the WHITE wire marked "TO MOTOR Connect the WHITE wire from the fan to the WHITE wire marked "TO MOTOR

N" from the receiver. Connect the BLUE wire from the fan to the BLUE wire N" from the receiver. Connect the BLUE wire from the fan to the BLUE wire

marked "FOR LIGHT" from the receiver. Secure all the wire connections with marked "FOR LIGHT" from the receiver. Secure all the wire connections with

the plastic wire connectors provided. (Fig. 14)the plastic wire connectors provided. (Fig. 14)

Step 3. Step 3. Remote Receiver to Outlet Box Electrical Connections: Connect the Remote Receiver to Outlet Box Electrical Connections: Connect the

BLACK (hot) wire from the ceiling to the BLACK wire marked "AC IN L" from BLACK (hot) wire from the ceiling to the BLACK wire marked "AC IN L" from

the receiver. Connect the WHITE (Neutral) wire from the ceiling to the WHITE the receiver. Connect the WHITE (Neutral) wire from the ceiling to the WHITE

wire marked "AC IN N" from the receiver. Secure all the wire connections with wire marked "AC IN N" from the receiver. Secure all the wire connections with

the plastic wire connectors provided. (Fig. 14) the plastic wire connectors provided. (Fig. 14)

Fig. 13

Fig. 14

Receiver Mounting Bracket

Outlex box

White

Green or bare copper (ground)

White("AC IN N")

White("TO MOTOR N")

Ground wire

White (Neutral)

Black

Black("AC IN L")

Receiver

Black ("TO MOTOR L")

Black (motor)

Blue(FOR LIGHT)

Blue(for light)

52" Range LED | 11

MAKE THE ELECTRICAL CONNECTIONS

FINISHING THE MOTOR INSTALLATION

Step 4. Step 4. If your outlet box has a ground wire ( green or bare copper ) connect If your outlet box has a ground wire ( green or bare copper ) connect

it to the fan ground wires : otherwise connect the fan ground wire to the it to the fan ground wires : otherwise connect the fan ground wire to the

mounting bracket. Secure the wire connection with a plastic nut provided. mounting bracket. Secure the wire connection with a plastic nut provided.

After connecting the wires, spread them apart so that the green and white After connecting the wires, spread them apart so that the green and white

wires are on one side of the outlet box and black and blue wires are on the wires are on one side of the outlet box and black and blue wires are on the

other side. (Fig. 14)other side. (Fig. 14)

NOTE:NOTE: Carefully tuck the wire connections up into the outlet box. Carefully tuck the wire connections up into the outlet box.

NOTE:NOTE: Fan must be installed at a maximum distance of 30 feet from the Fan must be installed at a maximum distance of 30 feet from the

transmitting unit for proper signal transmission between the transmitting transmitting unit for proper signal transmission between the transmitting

unit and the fan’s receiving unit.unit and the fan’s receiving unit.

Step 1. Step 1. Remove one of the two shoulder screws in the mounting bracket. Remove one of the two shoulder screws in the mounting bracket.

Loosen the second shoulder screw without fully removing it. (Fig. 15)Loosen the second shoulder screw without fully removing it. (Fig. 15)

Step 2. Step 2. Assemble canopy by rotating key slot in canopy over shoulder Assemble canopy by rotating key slot in canopy over shoulder

screw in mounting bracket. Reinstall the shoulder screw that was previously screw in mounting bracket. Reinstall the shoulder screw that was previously

removed, then retighten two shoulder screws securely. (Fig.16)removed, then retighten two shoulder screws securely. (Fig.16)

Fig. 15

Fig. 16

Shoulder Screw

Mounting Bracket

Canopy

Shoulder Screw

or

12 | KICHLER.COM

FINISHING THE MOTOR INSTALLATION

ATTACHING THE FAN BLADES

Step 3. Step 3. Securely attach and tighten the canopy hole cover over the shoulder Securely attach and tighten the canopy hole cover over the shoulder

screws in the mounting bracket utilizing the keyslot twist-lock feature. (Fig.17)screws in the mounting bracket utilizing the keyslot twist-lock feature. (Fig.17)

NOTE:NOTE: Before continuing, make sure the power is disconnected by turning Before continuing, make sure the power is disconnected by turning

o the circuit breaker or removing the fuse at the circuit box.o the circuit breaker or removing the fuse at the circuit box.

Step 1.Step 1. Install the 6 blades onto the motor by using the screws provided, Install the 6 blades onto the motor by using the screws provided,

tighten them securely. (Fig.18)tighten them securely. (Fig.18)

Fig. 17

Fig. 18

Canopy Hole Cover

Blade

Blade Screw

52" Range LED | 13

INSTALLING THE BLADE HOLDER

Step 1. Step 1. Place the blade holder to the blade as shown, and securely Place the blade holder to the blade as shown, and securely

tighten with two blade holder screws found in the hardware pack. tighten with two blade holder screws found in the hardware pack.

Repeat for the remaining blade holders. (Fig. 19)Repeat for the remaining blade holders. (Fig. 19)

Fig. 19a

Fig. 19b

Blade Holder

14 | KICHLER.COM

INSTALLING THE SWITCH HOUSING

Step 1. Step 1. Remove one of three screws which preinstalled on mounting plate and Remove one of three screws which preinstalled on mounting plate and

keep for later use. Loosen the other two (do not remove). Place the two slot keep for later use. Loosen the other two (do not remove). Place the two slot

holes on the switch housing over the 2 screws previously loosened from the holes on the switch housing over the 2 screws previously loosened from the

mounting plate. Rotate the switch housing until it locks in place at the narrow mounting plate. Rotate the switch housing until it locks in place at the narrow

end of the key holes. Securely by tightening the 2 screws previously loosened end of the key holes. Securely by tightening the 2 screws previously loosened

and the one previously removed. (Fig. 20) and the one previously removed. (Fig. 20)

Fig. 20a

Fig. 20b

Mounting Plate

Switch Housing

Screw

52" Range LED | 15

INSTALLING THE LIGHT KIT AND ACRYLIC SHADE

NOTE:NOTE: Before continuing installation, confirm that the power is still turned o Before continuing installation, confirm that the power is still turned o

at the main circuit breaker or by removing the circuit fuse. Turning the power at the main circuit breaker or by removing the circuit fuse. Turning the power

o using a wall switch is not sucient to prevent electrical stock.o using a wall switch is not sucient to prevent electrical stock.

Step 1.Step 1. Remove one of three screws on the switch housing and keep for later Remove one of three screws on the switch housing and keep for later

use, loose the other two (do not remove). (Fig. 21) use, loose the other two (do not remove). (Fig. 21)

Step 2.Step 2. Hold the light kit close to the switch housing and connect the WHITE Hold the light kit close to the switch housing and connect the WHITE

wires from the light kit and fan by pushing the connectors together. Follow wires from the light kit and fan by pushing the connectors together. Follow

the same procedure with the BLACK wires. (Fig. 22) the same procedure with the BLACK wires. (Fig. 22)

Step 3. Step 3. Tuck the connections neatly into the light kit. Place the two slot holes Tuck the connections neatly into the light kit. Place the two slot holes

on the light kit over two (2) screws previously loosened from the switch on the light kit over two (2) screws previously loosened from the switch

housing. Rotate the light kit until it locks in place at he narrow end of the housing. Rotate the light kit until it locks in place at he narrow end of the

key holes. Securely tighten two(2) screws previously loosened and the one key holes. Securely tighten two(2) screws previously loosened and the one

previously removed. (Fig. 22) previously removed. (Fig. 22)

Step 4Step 4. Secure the acrylic shade to switch housing by twisting in a clockwise . Secure the acrylic shade to switch housing by twisting in a clockwise

direction, twist the acrylic shade gradually until it snaps on to the switch direction, twist the acrylic shade gradually until it snaps on to the switch

housing. Do not over - tighten. (Fig. 23)housing. Do not over - tighten. (Fig. 23)

Fig. 21

Fig. 23

Fig. 22

Switch Housing

Screw

Light Kit

Acrylic Shade

16 | KICHLER.COM

Remote Control

Fig. 26

Fig. 25

Fig. 24

Fig. 27

OPERATING INSTRUCTIONS

Restore electrical power to the outlet box by turning the electricity on the Restore electrical power to the outlet box by turning the electricity on the

main fuse box.main fuse box.

Step 1.Step 1. Select a location to install your handset control holder, install the Select a location to install your handset control holder, install the

holder as shown. (Fig. 24)holder as shown. (Fig. 24)

Step 2. Step 2. Remove remote battery door, connect 9V battery (included) with plug Remove remote battery door, connect 9V battery (included) with plug

pressing the battery inside and replace the battery door. (Fig. 25)pressing the battery inside and replace the battery door. (Fig. 25)

NOTE:NOTE: If not used for long periods of time, remove battery to prevent If not used for long periods of time, remove battery to prevent

damage to remote control. Store remote control away from excessive heat damage to remote control. Store remote control away from excessive heat

and humidity.and humidity.

NOTE:NOTE: There are 16 combinations of code for setting up the remote control. There are 16 combinations of code for setting up the remote control.

If you do not use the dip switch set up by manufacturer, then you will need to If you do not use the dip switch set up by manufacturer, then you will need to

use the set up procedures listed below.(Fig. 26)use the set up procedures listed below.(Fig. 26)

a.)Set up the code combination you would like to use. a.)Set up the code combination you would like to use.

b.)After installing the unit and restoring power to the fan, press and hold the b.)After installing the unit and restoring power to the fan, press and hold the

“Light” button until the light flashes (on/off) 3 times, then the control and “Light” button until the light flashes (on/off) 3 times, then the control and

speed setting process is completed. You must pres the “Light” button within speed setting process is completed. You must pres the “Light” button within

30 seconds of restoring power to the fan.30 seconds of restoring power to the fan.

c.)If programming is unsuccessful, retry the above instructions.c.)If programming is unsuccessful, retry the above instructions.

Step 3. Step 3. The buttons control the fan speed and light as follows:(Fig. 27)The buttons control the fan speed and light as follows:(Fig. 27)

3 Low speed3 Low speed

2 Medium speed2 Medium speed

1 High speed1 High speed

0 To turn o the fan0 To turn o the fan

Press light key quickly to turn light on or o Press light key quickly to turn light on or o

Receiver

52" Range LED | 17

OPERATING INSTRUCTIONS

For DIMMER function: press and hold button to dim the light. The light will For DIMMER function: press and hold button to dim the light. The light will

cycle from bright to dim to bright until button is released. Light will maintain cycle from bright to dim to bright until button is released. Light will maintain

last setting if turned off. This remote has a memory function. The remote last setting if turned off. This remote has a memory function. The remote

stores the fan speed and light setting when the fan is turned o. When the stores the fan speed and light setting when the fan is turned o. When the

fan is turned on again, it starts with the most recent setting. fan is turned on again, it starts with the most recent setting.

Step 4. Step 4. Use the fan reversing switch to optimize your fan for seasonal Use the fan reversing switch to optimize your fan for seasonal

performance.performance.

WARNING: WARNING: do not operate reversing switch while fan blades are in motion. do not operate reversing switch while fan blades are in motion.

Fan must be turned o and blades stopped before reversing blade direction.Fan must be turned o and blades stopped before reversing blade direction.

Warm Weather Operation: Warm Weather Operation: Forward (counter clockwise). A downward airflow Forward (counter clockwise). A downward airflow

creates a cooling eect (Fig. 29). This allows you to set your air conditioner creates a cooling eect (Fig. 29). This allows you to set your air conditioner

on a warmer setting without aecting your general comfort.on a warmer setting without aecting your general comfort.

Cool Weather Operation:Cool Weather Operation: Reverse (clockwise). An upward airflow moves Reverse (clockwise). An upward airflow moves

warm air o the ceiling areas (Fig. 30). This allows you to set your heating unit warm air o the ceiling areas (Fig. 30). This allows you to set your heating unit

on a cooler setting without aecting your general comfort.on a cooler setting without aecting your general comfort.

Reverse switch

Fig. 28

Fig. 29 Fig. 30

18 | KICHLER.COM

TROUBLESHOOTING

ProblemProblem

Fan will not start.Fan will not start.

Fan sounds noisy.Fan sounds noisy.

Fan wobble.Fan wobble.

Remote control Remote control

malfunction.malfunction.

SolutionSolution

1. Check circuit fuses or breakers.1. Check circuit fuses or breakers.

2. Check all electrical connections to ensure proper contact. 2. Check all electrical connections to ensure proper contact. CAUTION: CAUTION: Make sure the main power is OFF when checking Make sure the main power is OFF when checking

any electrical connection.any electrical connection.

3. Make sure the transmitter batteries are installed properly. Positive (+) side facing out.3. Make sure the transmitter batteries are installed properly. Positive (+) side facing out.

4. Ensure the batteries have a good charge.4. Ensure the batteries have a good charge.

1. Make sure all motor housing screws are snug.1. Make sure all motor housing screws are snug.

2. Make sure the screws that attach the fan blade brackets to the motor are tight.2. Make sure the screws that attach the fan blade brackets to the motor are tight.

3. Make sure wire nut connections are not rubbing against each other or the interior wall of the switch housing. 3. Make sure wire nut connections are not rubbing against each other or the interior wall of the switch housing.

CAUTION: CAUTION: Make sure main power is o.Make sure main power is o.

4. Allow a 24-hour "breaking-in" period. Most noise associated with a new fan disappears during this time.4. Allow a 24-hour "breaking-in" period. Most noise associated with a new fan disappears during this time.

5. If using an optional light kit, make sure the screws securing the glassware are tight. Make sure the light bulbs are not 5. If using an optional light kit, make sure the screws securing the glassware are tight. Make sure the light bulbs are not

touching any other component.touching any other component.

6. Do not connect this fan to a wall mounted variable speed control(s). They are not compatible with ceiling fan motors or 6. Do not connect this fan to a wall mounted variable speed control(s). They are not compatible with ceiling fan motors or

remote controls.remote controls.

7. Make sure the upper canopy has a short distance from the ceiling. It should not touch the ceiling.7. Make sure the upper canopy has a short distance from the ceiling. It should not touch the ceiling.

1. Check that all blade and blade arm screws are secure.1. Check that all blade and blade arm screws are secure.

2. Most fan wobbling problems are caused when blade levels are unequal. Check this level by selecting a point on the ceiling 2. Most fan wobbling problems are caused when blade levels are unequal. Check this level by selecting a point on the ceiling

above the tip of one of the blades. Measure this distance. Rotate the fan until the next blade is positioned for measurement. above the tip of one of the blades. Measure this distance. Rotate the fan until the next blade is positioned for measurement.

Repeat for each blade. The distance deviation should be equal within 1/8".Repeat for each blade. The distance deviation should be equal within 1/8".

3. If the blade wobble is still noticeable, interchanging two adjacent (side by side) blades can redistribute the weight and 3. If the blade wobble is still noticeable, interchanging two adjacent (side by side) blades can redistribute the weight and

possibly result in smoother operation. possibly result in smoother operation.

1.Ceiling Fans with remote control systems CAN NOT be operated in conjunction with any other control system EXCEPT a 1.Ceiling Fans with remote control systems CAN NOT be operated in conjunction with any other control system EXCEPT a

basic On/o wall switch, if desired.basic On/o wall switch, if desired.

52" Range LED | 19

FCC Information

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1.)This device may not cause harmful interference, and

2.)This device must accept any interference received, including interference that may cause undesired operation.

Note: Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by

turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician or help.

www.kichler.com

KICHLER LIGHTING

7711 EAST PLEASANT VALLEY ROAD

CLEVELAND, OHIO 44131-8010

CUSTOMER SERVICE 866.558.5706

8:00 AM TO 5:00 PM EST, MONDAY - FRIDAY

La page charge ...

Kichler 300317DBK Manuel utilisateur

Kichler 300317DBK Manuel utilisateur

dans d''autres langues

Documents connexes

Autres documents