UTEC WG233 Manuel utilisateur

WG233
Marque
UTEC
Modèle
WG233
Taper
Manuel utilisateur
Page 1 of 2
UTEC, Inc.
111 E. Wayne St.
Suite 800
Fort Wayne, IN 46802
+1 (260) 358-0888 Phone
+1 (260) 358-3235 Fax
Wi-Fi Module:
The module WG233E is manufactured by SkyLab M&C Technology Co. The module is
capable of operating in IEEE 802.11a/b/g/n/ac and can operate in both the 2.4GHz and
5.8GHz band. The module operates in 2T2R mode and supports 2 external antenna
connection points through two IPEX connectors. To prevent unwanted emission noise,
the radio IC is encapsulated with a with a metalized EMI shield.
The wifi radio IC consists of a Realtek RTL8812 chipset. The interface between the
module and the microprocessor is USB 2.0 running at high speed and operates off of
3.3V. Refer to the pinout of the module below.
Component
Model number
Specification
Manufacturer
FCC ID
RF
module/chip
WG233EC
IEEE802.11 a/b/g/n/ac
2.4G&5G WLAN dual
antenna
SKYLABS
2ACOE-
WG233
Antenna 1
&2
SKA15_220
Note: Sky labs
internal model
number is MST-
24/58BC-7
MAGNETIC DUEL
BAND
ANTENNA/SUCKER
TYPE
SKYLABS
Not
Applicable
Cable
SKA113_75
75mm SMA/IPEX
CABLE, ROHS
COMPLIANT
SKYLABS
Not
Applicable
Table 1 RF Component details
Page 2 of 2
Skylab Module FCC Details:
Original Company Name: Skylab M&C Technology co., ltd
Original Model: WG233
Original FCC ID: 2ACOE-WG233
The original granted date is: May 27, 2020
Skylab Module ISED Details:
Original Company Name: Skylab M&C Technology co., ltd
Original IC: 20742-WG233
Original Marketing Name (PMN): WIFI MODULE
Original Model (HVIN):WG233
Original Firmware (FVIN): V1.0
UTEC, Inc. intend to market the product with new identification. The new identification
is placed on the Skylab’s Module.
New Company Name: UTEC, Inc.
New Model: WG233
New FCC ID: 2AK6N-WG233
New ISED ID: 703A-WG233
This device complies with part 15 of the FCC rules and with Innovation, Science and
Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the
following two conditions:
1) This device may not cause interference.
2) This device must accept any interference, including interference that may cause
undesired operation of the device.
FCC 15.21 statement:
Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
L’émetteur/récepteur exempt de license contenu dans le présent appareil est conforme
aux CNR d’Innovation, Sciences et Développement économique Canada applicables
aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions
suivantes :
1. L’appareil ne doit pas produire de brouillage;
2. L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage
est susceptible d’en compromettre le fonctionnement.
End product labeling:
This transmitter module is authorized only for use in device where the antenna may be
installed such that 20 cm may be maintained between the antenna and users. The final
end product must be labeled in a visible area with the following: “Contains FCC ID:
2AK6N-WG233” and Contains IC: 703A-WG233.
  • Page 1 1
  • Page 2 2

UTEC WG233 Manuel utilisateur

WG233
Marque
UTEC
Modèle
WG233
Taper
Manuel utilisateur
Télécharger le PDF
rapport

dans d''autres langues

Autres documents