sunjoe SPX3001 Le manuel du propriétaire

Marque: sunjoe

Modèle: SPX3001

Catégorie: Outils de jardin

Taper: Le manuel du propriétaire

SAVE THESE INSTRUCTIONS

OPERATOR’S MANUAL

Model SPX3001 Form No. SJ-SPX3001-880E-MR12

14.5A ELECTRIC PRESSURE WASHER

WITH HOSE REEL

Original instructions.

A Division of Snow Joe, LLC

IMPORTANT!

Safety Instructions

All Operators Must Read These

Instructions Before Use

mWARNING! This indicates a hazardous situation, which,

if not avoided, could result in death or serious injury.

mCAUTION! This indicates a hazardous situation, which,

if not avoided, could result in minor or moderate injury.

mDANGER! This indicates a hazardous situation, which,

if not followed, will result in death or serious injury.

General Safety

mWARNING! This appliance is not intended for use

by children or by unassisted, unsupervised persons whose

physical, sensory or mental capabilities prevent them from

using it safely. Children should be supervised to ensure that

they do not play with the appliance.

Before starting up your machine, please check it carefully for

any defects. If you nd any, do not start up your machine.

Contact your authorized Snow Joe® + Sun Joe® dealer or

call the Snow Joe® + Sun Joe® customer service center at

1-866-SNOWJOE (1-866-766-9563).

mWARNING! When using the pressure washer, basic

safety precautions should always be followed to reduce the

risk of re, electric shock, and personal injury. These include:

• Know your product – Know how to stop the machine and

bleed pressure quickly. Thoroughly familiarize yourself with

the controls.

• Keep bystanders away – All visitors and pets should be

kept a safe distance away from the work area.

• Use the right product – Do not use this machine for any

job except that for which it is intended.

• Dress properly – Do not wear loose clothing or jewelry.

They can get caught in moving parts. Protective rubber

gloves and non-slip footwear are recommended when

working outdoors.

• mCAUTION! – Exercise caution to avoid slipping or falling.

Wear protective footwear that will protect your feet and

improve your footing on slippery surfaces.

• Stay alert – Watch what you are doing. Use common

sense. Do not operate the pressure washer when you are

tired, or under the inuence of alcohol or drugs.

• Do not overreach – Keep proper footing and balance at

all times.

• Avoid unintentional starting – Do not carry a plugged-

in machine with your nger on the trigger. Make sure the

switch is o before plugging in the machine.

• Do not abuse the cord – Never carry the machine by the

cord or yank the cord to disconnect it from the receptacle.

Keep the cord away from heat, oil, and sharp edges.

• Use safety glasses – Also use safety footwear, snug-tting

clothing, protective gloves, hearing and head protection.

• Check the water temperature – This pressure washer is

not meant to pump hot water. NEVER connect it to a hot

water supply as it will signicantly reduce the life of the

pump.

• Store indoors – NEVER store the pressure washer

outdoors or where it could freeze. The pump could be

seriously damaged.

• Ground Fault Circuit Interrupter (GFCI) – Protection

should be provided on the circuits or outlets to be used

for this pressure washer. Receptacles are available having

built-in GFCI protection and may be used for this measure

of safety.

• Inspect electrical cables – The insulation of the power

cord should be perfectly intact. If the power cord is

damaged or shows any signs of wear or tear, do not use the

pressure washer. Contact your authorized Snow Joe® +

Sun Joe® dealer or call the Snow Joe® + Sun Joe® customer

service center at 1-866-SNOWJOE (1-866-766-9563).

mWARNING! Do not use this appliance without reading

this instruction manual.

mWARNING! This appliance has been designed for

use with cleaning agents that are recommended by the

manufacturer. The use of other cleaning agents or chemicals

may adversely aect the safety of the appliance.

mWARNING! Do not use the appliance within range of

persons unless they are wearing protective clothing.

mWARNING! High-pressure jets can be dangerous if

subject to misuse. The jet must not be directed at persons,

pets, live electrical equipment, or the appliance itself.

• Do not direct the jet at yourself or others in order to clean

clothes or footwear.

• Risk of explosion – Do not spray ammable liquids.

• Disconnect the tool – Disconnect from the electrical power

supply before performing any maintenance task.

• Keep children away – This high-pressure electric

power washer must not be used by children or untrained

personnel.

• To ensure appliance safety, use only original replacement

parts from the manufacturer or those approved by the

manufacturer.

mWARNING! Water that has owed through backow

preventers is considered to be non-potable.

mWARNING! During cleaning, maintenance or when

replacing parts, the machine must be disconnected from its

power source by removing the plug from the socket outlet.

mWARNING! High-pressure hoses, ttings, and

couplings are important for the safe operation of the appliance.

Use only hoses, ttings, and couplings recommended by the

manufacturer.

• Check for damaged parts – Do not use the appliance if

the supply cord or other important parts of the appliance

are damaged (e.g. safety devices, high-pressure hoses,

trigger gun).

mWARNING! If an extension cord is used, the plug and

socket must be of watertight construction.

mWARNING! Inadequate extension cords can be

dangerous.

• This high-pressure electric power washer must not be used

at temperatures below 32ºF (0°C).

mWARNING! Power cords on drums should always be

completely unwound to prevent the cord from overheating.

• Power cord connections should be kept dry and o the

ground.

• If the power cord is damaged, do not use the appliance.

Contact your authorized Snow Joe® + Sun Joe® dealer or

call the Snow Joe® + Sun Joe® customer service center at

1-866-SNOWJOE (1-866-766-9563).

• Keep the machine on a stable, at surface during operation,

handling, transportation, and storage. Sudden overturn of

the machine can cause bodily injury.

• In the event of an accident or breakdown, switch o the

machine immediately. (If contact with detergent occurs,

rinse with an abundance of clean water.)

Electrical Safety

ATTENTION: If there are problems with the electrical

MAINS, short voltage drops may appear when starting the

equipment. This can, in turn, inuence other equipment

(e.g. cause a lamp to blink). If the MAINS-IMPEDANCE Zmax

< 0.335 OHM, such disturbances are not expected. (If you

require assistance, contact your local supply authority for

further information.)

mWARNING! Electrical Shock Hazard – Before starting

up your machine, please check it carefully for any defects. If

you nd any, do not start up your machine and contact your

distributor.

The following should be observed when connecting the

high-pressure electric power washer to the electric supply:

• The electric supply connection should be performed by a

qualied person.

• The electric supply to this appliance should include either

a residual current device that will interrupt the supply if the

leakage current to the earth exceeds 30 mA for 30 ms or a

device that will interrupt the earth circuit (GFCI).

IMPORTANT: Only use water without any impurities.

If there is a risk of running sand into the inlet water (i.e. from

your own well), an additional lter should be installed.

Safety devices

The unloader valve can reduce pressure if it exceeds preset

values. The spray gun features a locking device. When the lock

is activated, the spray gun cannot be operated.

1. Thermal sensor – A thermal sensor protects the motor

against overloading. The machine will restart after a few

minutes when the thermal sensor has cooled.

2. Double insulation – In a double-insulated appliance, two

systems of insulation are provided instead of grounding.

No grounding means is provided on a double-insulated

appliance, nor should a means for grounding be added

to the appliance. Servicing a double-insulated appliance

requires extreme care and knowledge of the system, and

should be performed only by qualied service personnel at

an authorized Snow Joe® + Sun Joe® dealer. Replacement

parts for a double-insulated appliance must be identical

to the parts they replace. A double-insulated appliance

is marked with the words “Double Insulation” or “Double

Insulated.” The symbol (square within a square) may

also be marked on the appliance.

3. Ground fault circuit interrupter (GFCI) protection – This

pressure washer is provided with a ground-fault circuit-

interrupter (GFCI) built into the plug of the power-supply

cord. This device provides additional protection from

the risk of electric shock. Should replacement of the

plug or the cord become necessary, use only identical

replacement parts that include GFCI protection.

4. It is not recommended to use an extension cord with

this pressure washer. The unit comes standard with a

35 ft GFCI power cable. Using an extension cord may

cause a drop in line voltage resulting in loss of power and

overheating.

5. To reduce the risk of electric shock, this appliance has

a polarized plug (i.e. one blade is wider than the other).

The appliance plug will t into a polarized outlet only

one way.

If the appliance plug does not t fully into the outlet,

reverse the plug. If the plug still does not t, make sure

that you are using the correct polarized wall outlet.

If the plug still does not t, contact a qualied electrician

to install the proper wall outlet. Do not modify the

appliance plug, power cord receptacle, or power cord

plug in any way.

Use only extension cords that are intended for outdoor

use. These extension cords are identied by marking

"Acceptable for use with outdoor appliance; store indoors

while not in use". Use only extension cord having an

electrical rating not less than the rating of the product. Do

not use damaged extension cords. Examine extension

cord before using and replace if damaged. Do not

abuse extension cord and do not yank on any cord to

disconnect. Keep cord away from heat and sharp edges.

Always disconnect extension cord from the receptacle

before disconnecting the product from the extension cord.

6. To prevent the appliance cord from disconnecting from the

extension cord during operation, make a knot with the two

cords as shown in Table 1.

7. Do not abuse the cord. Never pull the pressure washer

by the cord or yank the cord to disconnect it from the

receptacle. Keep the cord away from heat, oil, and

sharp edges.

Risk of electrocution

• Inspect cord before using.

• Do not use if cord is damaged.

• Keep all connections dry and o the ground.

• Do not touch plug with wet hands.

• Keep cord away from heat and sharp edges.

• Do not spray electrical apparatus and wiring.

Risk of explosion

• Do not spray ammable liquids.

• Do not use acids, bases, solvents, or any ammable

material in this product. These substances can cause

physical injuries to the operator and irreversible damage to

the machine.

Additional safety instructions

• High pressure: keep clear of nozzle.

• Injection hazard: equipment can cause serious injury if the

spray penetrates the skin.

• Do not point the gun at anyone or at any part of the body.

• In case of skin penetration, seek medical aid immediately.

• Before servicing, cleaning, or removing any parts, shut o

the power and relieve pressure.

• This machine is not suitable for connection to the potable

water mains.

m WARNING m

Electric shock may cause SEVERE INJURY or

DEATH. Heed these warnings:

• Do not allow any part of the electric pressure washer

to make contact with water while it is in operation. If

the appliance becomes wet while turned o, wipe dry

before starting.

• Do not use an extension cord over 25 ft. The

pressure washer comes equipped with a 35 ft power

cable. Combined cord length must not exceed 60 ft.

Any extension cord must be 14-gauge (or heavier) to

safely power the pressure washer.

• Do not touch the appliance or its plug with wet hands

or while standing in water. Wearing rubber boots

oers some protection.

EXTENSION CORD CHART

Cord Length:

Min. Wire Gauge (A.W.G.):

25 ft (7.6 m)

(B) Connect plug and receptacle

Cord set Appliance cord

(A) Tie cord as shown

Table 1. Method of Securing Extension Cord

Product Description

Purpose

• This high-pressure electric power washer is intended for

residential use to clean vehicles, machines, buildings,

facades, etc.

Areas of application

• Never use the machine in potentially explosive areas under

any circumstances!

• The operating temperature must be between 32ºF (0ºC) and

104ºF (40ºC).

• The machine consists of an assembly with a pump, which

is encased in a shock-absorbing housing. To provide the

operator with an optimal working position, the machine is

equipped with a spray wand and a non-slip handle grip,

whose shape and conguration comply with applicable

regulations.

• Do not cover or modify the spray wand or the spray nozzles

in any way.

• The high-pressure electric power washer is designed to be

used with cold or lukewarm water; higher temperatures can

damage the pump.

• Do not use water that is dirty, gritty, or contains any

chemical products, as these could impair operation and

shorten the life of the machine.

Safety Symbols

The following table depicts and describes safety symbols that may appear on this product. Read, understand, and follow all

instructions on the machine before attempting to assemble and operate.

To reduce the risk of injury, user

must keep all bystanders at least

49 ft (15 m) away.

Sound power level is 96 dB(A).

Always keep the power cable

away from heat sources, oils, or

sharp edges. Immediately remove

plug from the mains if the cable is

damaged, frayed, or entangled.

READ THE OPERATOR'S

MANUAL(S) – Read, understand,

and follow all instructions in the

user manual(s) before attempting

to assemble and operate.

SAFETY ALERT – Indicates a

precaution, a warning, or a danger.

WEAR EYE AND HEARING

PROTECTION – For protection

against injury, wear ear defenders

and safety goggles.

Double Insulation – When servicing,

use only identical replacement parts.

WARNING! Do not expose the

unit to rain or wet conditions.

Keep dry.

Machine not suitable for connection

to the potable water mains.

WARNING! Electrical shock hazard.

WARNING! Turn the machine OFF

and disconnect it from the power

supply before inspecting, cleaning,

changing accessories, or conducting

any other maintenance task.

Symbols SymbolsDescriptions Descriptions

Wear non-slip footwear that will

protect your feet and improve your

footing on slippery surfaces.

Wear safety gloves during

use to protect hands.

Store indoors. Never store the

pressure washer outdoors.

If the pump freezes, permanent

damage may result.

Know Your Electric Pressure Washer

Read the owner’s manual and safety instructions carefully before operating the electric pressure washer. Compare the illustration

below to the electric pressure washer in order to familiarize yourself with the location of the various controls and adjustments.

Save this manual for future reference.

1. Safety lock (Locate lock in center of trigger. Pull up and snap in place. See Fig. 12, pg. 9)

2. Trigger

3. Trigger gun

4. High-pressure hose

5. Spray wand

6. Water inlet/garden hose connection

7. Transportation handle

8. Onboard storage for Quick-Connect nozzles

9. High pressure hose reel

10. Hand crank

11. Power cord with GFCI

12. On/O switch

13. Detergent dial

14. High-pressure hose connection

15. Cord holder

16. Trigger gun holder

17. Removable detergent tank

18. Detergent tank holder

19. Spray wand protector

20. Wheel (2)

21. Water outlet/high-pressure connection

22. Garden hose adapter (female coupler)

23. Needle clean out tool

24. 0º Quick-Connect nozzle (red)

25. 15º Quick-Connect nozzle (yellow)

26. 25º Quick-Connect nozzle (green)

27. 40º Quick-Connect nozzle (gray)

28. Soap Quick-Connect nozzle (black)

15º

25º

0º

SOAP

40º

24 25 26 27 28

10 11

Technical Data

Rated Voltage ........................................................ 120V ~ 60 Hz

Motor ........................................................................... 14.5-amp

Max Water Inlet Temperature ................................... 104ºF/40ºC

Max Water Inlet Pressure .............................................. 0.7 MPa

Detergent Tank Capacity ................................... 40.6  oz (1.2 L)

High Pressure Hose Length ....................................... 20 ft (6 m)

Power Cord Length ............................................... 35 ft (10.7 m)

Rated Pressure ............................................................ 1450 PSI

Rated Flow ...............................................1.24 GPM (4.7 L/min)

Net Weight ........................................................ 30.9 lbs (14 kg)

Unpacking

Carton Contents

• Pressure washer unit

• Trigger gun

• Spray wand

• Five (5) Quick-Connect nozzles (0º, 15º, 25º, 40º and Soap)

• Two (2) small screws

• Spray wand protector

• Trigger gun holder

• Needle clean out tool

• Garden hose adapter (female coupler)

• Manual with registration card

1. Carefully remove the pressure washer and check to see

that all of the above items are supplied.

2. Inspect the product carefully to make sure no breakage or

damage occurred during shipping. If you nd damaged or

missing parts, DO NOT return the unit to the store. Please

call the Snow Joe® + Sun Joe® customer service center at

1-866-SNOWJOE (1-866-766-9563).

NOTE: Do not discard the shipping carton and packaging

material until you are ready to use your new electric

pressure washer. The packaging is made of recyclable

materials. Properly dispose of these materials in

accordance with local regulations.

IMPORTANT! The equipment and packaging material are

not toys. Do not let children play with plastic bags, foils,

or small parts. These items can be swallowed and pose a

suocation risk!

mWARNING! Do not connect to power supply until

assembly is complete. Failure to comply could result in

accidental starting and possible serious personal injury.

Assembly

1. Position the washer as CLOSE as possible to the

water supply.

2. The washer must be used on a secure and stable surface

in a standing, upright position (Fig. 1).

3. Slide the trigger gun holder into position and secure it in

place with one screw (Fig. 2).

4. To assemble the spray wand protector, rst snap the tabs

into the slots located at the bottom left side of the unit,

and then secure it in place with the other screw (Fig. 3).

Fig. 1

Fig. 2

Trigger gun holder

Screw

Fig. 3

Screw Spray wand protector

5. Fit the stainless steel lance into the trigger gun and rotate

the collar until the two parts are completely locked (Fig. 4).

6. Connect the high-pressure hose to the trigger gun

(Fig. 5).

mWARNING! Keep hose away from sharp objects.

Bursting hoses may cause injury. Examine hoses regularly and

replace if damaged. Do not attempt to mend a damaged hose.

7. Connect the garden hose adapter (female coupler) to

the water inlet of the pressure washer, then thread your

garden hose (male end) into the garden hose adapter

(Fig. 6). The garden hose must have an internal

diameter of at least 13 mm (1/2 in.) and must be

reinforced. The water supply must be at least equal to

the washer delivery capacity.

NOTE: The machine is not suitable for connection to a

potable water main.

8. Attach garden hose to water supply (Fig. 7).

mWARNING! The intake water temperature must not

exceed 104ºF/40ºC. The water supply must not exceed

0.7 MPa.

mCAUTION! The washer must only be used with clean

water; use of unltered water containing corrosive chemicals

will damage the washer.

9. Make sure the motor switch is pushed to the OFF (0)

position before plugging the unit into the power outlet

(Fig. 8).

Fig. 4

Stainless

steel lance

Trigger gun

Collar

High-pressure hose

Trigger gun

Fig. 5

Fig. 6 Water inlet

(female coupler)

(FRONT)

Garden hose

This end to the

water inlet on

the unit

Garden hose

(male end)

Fig. 7

Connect to water supply

Garden hose

OFF/O

ON/I

Fig. 8

10. Check that the electrical supply voltage and frequency

(Volt/Hz) correspond to those specied on the pressure

washer rating plate. If the power supply is correct, you

may now plug the pressure washer into the power outlet

(Fig. 9).

NOTE: The GFCI may need to be reset when rst plugged

into the electric outlet. Press the "Reset" button until the

power light indicator on the GFCI illuminates.

Operation

mIMPORTANT! This pressure washer is equipped with

a micro-switch sensitive to water ow. This Total Stop System

(TSS) senses water ow in the pump. When the trigger is

released, water stops owing through the pump. The TSS then

automatically turns the motor o to protect the pump from

overheating, thus saving energy and prolonging pump life.

1. Turn the water supply tap on completely.

2. Make sure the safety lock is down and in its original

position (Fig. 10), then press the trigger for a few seconds

until water ow is steady. This will allow air to escape and

discharge any residual pressure in the hose.

3. Turn the switch to the ON (I) position to start the pressure

washer (Fig. 11).

Using the nozzles

Before beginning any cleaning task, determine the best nozzle

for the job. Each of the nozzles has a dierent spray pattern.

The nozzle patterns are 40˚ (for gentle cleaning), 25˚ (for

all-purpose cleaning), 15˚ (for tough jobs), 0˚ (for spot cleaning

or hard-to-reach areas) and the Soap nozzle (for detergent

application).

mCAUTION! NEVER change nozzles without locking the

safety lock on the trigger handle.

mWARNING! High-pressure jets can be dangerous if

subject to misuse. The jet must not be directed at persons,

pets, live electrical equipment, or the appliance itself.

This electric pressure washer is equipped with ve (5) Quick-

Connect nozzles that easily snap onto the Quick-Connect

collar of the spray wand.

To connect a nozzle to the spray wand:

1. Turn o the pressure washer and shut o the water supply.

Pull the trigger to release water pressure.

2. Engage the safety lock on the trigger handle by pushing

up on the safety lock until it clicks into the slot (Fig. 12).

3. Snap the desired nozzle onto the Quick-Connect collar

until it clicks into place (Fig. 13).

RESET

TEST

Fig. 9

GFCI

Power light

indicator

Reset

Fig. 10 Safety lock

Slot

Trigger

OFF/O

ON/I

Fig. 11

Fig. 12

Safety lock

Slot

To disconnect a nozzle from the spray wand once the cleaning

job is complete:

4. Turn o the pressure washer and shut o the water supply.

Pull the trigger to release water pressure.

5. Engage the safety lock on the trigger handle by pushing

up on the safety lock until it clicks into the slot (Fig. 12).

6. Remove the nozzle by placing your hand over the nozzle

while pulling back on the Quick-Connect collar.

mWARNING! Do not make changes to the nozzle while

the trigger is engaged. Doing so could result in damage to the

pressure washer or injury to the user.

Working with detergents

When cleaning with the pressure washer, some cleaning tasks

can be solved with water alone, but for most tasks cleaning

with detergent allows for more eective dirt removal.

mWARNING! Use only detergents designed for

Pressure Washers. DO NOT USE household detergents, acids,

alkaline solutions, bleaches, solvents, ammable material, or

industrial grade solutions. These could damage the pressure

washer. Many detergents may require mixing prior to use.

Prepare the cleaning solution as instructed on the solution

bottle.

1. Remove the cap and detergent suction tube from the

detergent bottle.

2. Gently pull the onboard detergent tank out of its storage

position and ll it with detergent designed specically for

use with pressure washers (Fig. 14).

3. Insert the suction tube back into the tank and cap the tank

closed. Push the tank back into storage position on the

unit.

4. Install the Soap nozzle (black) on the spray wand (Fig. 15).

mCAUTION! Always test the detergent in an

inconspicuous area before use.

5. Turn on the pressure washer. Pull the trigger to operate the

unit. The liquid detergent will automatically mix with water

and be discharged through the nozzle.

6. Turn the detergent dial to adjust the suction volume of the

detergent solution (Fig. 15).

7. Apply detergent from the bottom to the top of the dry

surface to be cleaned.

NOTE: Wetting the surface rst is not recommended as it

dilutes the detergent and reduces its cleaning ability.

8. Allow the detergent to remain on the surface for a short

time before rinsing. Do not allow the detergent to dry on

the surface.

mCAUTION! Damage may occur to painted surfaces if

the detergent is allowed to dry on the surface. Wash and rinse

a small section at a time. Avoid working on hot surfaces or in

direct sunlight.

Fig. 13

Nozzle

“Click”

Quick-Connect collar

Spray wand

Fig. 14

Detergent tank

Pressure washer

detergent

OFF/O

I/ON

Fig. 15

Detergent dial

9. When you have nished using the detergent injection

system, remove the detergent suction tube from the

detergent bottle and insert it into 1.3 gal (5 L) of fresh

water. Siphon water at low-pressure for one minute so that

all the detergent is ushed through the system. Remove

the detergent bottle and rinse it until it is thoroughly

cleaned.

mCAUTION! Failure to follow these cleaning instructions

will cause the injection system to become clogged and

inoperable.

Rinsing with the pressure washer

1. Turn o the pressure washer and shut o the water supply.

2. Pull the trigger to release water pressure.

3. Engage the safety lock on the trigger handle by pushing

up on the safety lock until it clicks into the slot (Fig. 12).

4. Remove the nozzle by placing your hand over the nozzle

while pulling back on the Quick-Connect collar.

5. Select the right nozzle for the job (Fig. 16):

I) The 0º intense-jet nozzle (red) is an extremely powerful

nozzle that delivers a high-pressure, pencil-point jet

stream. It is used to cut heavy dirt deposits in a small,

concentrated area. It is ideal for dissolving stubborn

substances, like tar and grease spots on concrete,

or for removing caked mud from equipment. Use this

nozzle to clean hard-to-reach areas including the

facades of 2-story buildings or the undersides of lawn

mowers and tractors.

NOTE: Care should be used when choosing the

right nozzle to avoid permanently gouging wood or

damaging fragile surfaces.

II) Use the 15º fan-tip nozzle (yellow) for intense cleaning

jobs on hard surfaces. Applications include stripping

paint, removing oil stains, grease, heavy mildew stains,

and rust from steel. This nozzle should only be used in

areas that can withstand the high-pressure from this

nozzle.

III) Use the 25º fan-tip nozzle (green) to clean home siding,

brick patios, wood decks, driveways, or sidewalks.

When using this nozzle, test a small area rst to avoid

surface damage.

IV) Use the 40º wide-spray tip nozzle (gray) to clean items

such as cars, trucks, boats, patio furniture, or lawn

equipment.

V) Use the Soap nozzle (black) for low-pressure detergent

application to clean equipment, remove mildew and

oxidation stains from houses, clean bricks or degrease

grimy surfaces.

NOTE: When using detergent, make sure that the

correct Soap nozzle (black) is installed. All of the other

colored nozzles will not work for detergent application.

6. Start at the top of the area to be rinsed and work down,

making sure to overlap the strokes.

mIMPORTANT! NEVER USE:

• Bleach, chlorine products, and other corrosive chemicals

• Liquids containing solvents (e.g. paint thinners, gasoline,

oils)

• Tri-sodium phosphate products

• Ammonia products

• Acid-based products

These chemicals will harm the unit and will damage

the cleaning surface.

Shutting down

1. Turn the switch to the OFF (0) position and unplug the

power cord from the outlet.

2. Turn o the water source.

3. Hold the trigger to release water pressure.

4. Disconnect the garden hose from the water inlet on

the unit.

5. Disconnect the high-pressure hose connection on the

trigger gun handle.

6. Release the trigger and engage the gun safety lock.

mWARNING! Turn o the water supply and squeeze the

trigger to depressurize the unit. Failure to do so could result in

personal injury due to discharge of high-pressure water.

Taking a break

If you are taking a break of ve minutes or more between

cleaning tasks:

1. Engage the gun safety lock.

2. Turn the switch to the OFF (0) position.

3. Unplug the power cord from the outlet.

15º

SOAP

25º 40º

0º

Fig. 16

Storage

Hose reel

1. Unlock the hose reel by pulling out on the handle out

(Fig. 17).

2. Turn the handle counterclockwise to wind the hose

(Fig. 18).

3. Wind the hose until you reach the hose's end.

4. Push the handle in to lock the reel.

mCAUTION! Always store your pressure washer in a

location where the temperature will not fall below 32ºF (0ºC).

The pump in this machine is susceptible to permanent damage

if it freezes. FREEZE DAMAGE IS NOT COVERED BY THE

WARRANTY.

• Store the pressure washer indoors in a dry, covered area

where it is not subject to adverse weather conditions.

• It is important to store this product in a frost-free area.

• Always empty water from all hoses, the pump, and the

detergent bottle before storing.

mCAUTION! The use of a pump protector is

recommended to prevent cold weather damage during storage

over the winter months.

Winterizing + long-term storage

If you must store your pressure washer in a location where

the temperature falls below 32ºF (0ºC), you can minimize the

chance of damage to your machine by utilizing the following

procedure:

• Disconnect all water connections.

• Turn on the machine for a few seconds until the remaining

water in the pump exits. Turn o immediately.

• Do not allow the high-pressure hose to become kinked.

• Store the machine and accessories in a room that does

not reach freezing temperatures.

• Do not store near a furnace or other sources of heat that

may dry out the pump seals.

• Operate the pressure washer with non-corrosive/non-toxic

anti-freeze, a pump saver, or a pump protector before

storing for the winter.

mWARNING! Before reusing, completely ush the unit

out with clear water. Anti-freeze products can damage

paintwork, so you must ensure there is no anti-freeze left in the

system before using it again.

Maintenance

mCAUTION! Before working on the pressure washer,

disconnect the plug from the power supply socket.

1. To ensure good performance, check and clean the water

inlet lter (Fig. 19). Remove the pre-lter and water inlet

lter and rinse with warm water to prevent any foreign

matter from clogging the pump (Figs. 20 – 21).

Fig. 17

Hose reel handle

Fig. 18

Hose reel handle

Garden hose adapter

Pre-lter

Fig. 19

(FRONT)

Waterinletlter

2. Clean the nozzle with the needle clean out tool provided

(Fig. 22). Remove the spray wand from the gun; remove

any dirt from the nozzle hole and rinse.

3. Remove additional debris by back ushing water through

the nozzle and spray wand. To do this, place the end of

your garden hose (with water running) to the tip of the

nozzle, pushing water and debris out of the back opening

of the nozzle and spray wand.

Circuit Diagram

A circuit diagram for the pressure washer is provided below for

your reference (Fig. 23).

Disposal

Recycling the washer

• Do not dispose of electrical appliances as unsorted

municipal waste. Use separate collection facilities.

• Contact your local government agency for information

regarding the collection systems available.

• If electrical appliances are disposed of in landlls

or dumps, hazardous substances can leak into the

groundwater and get into the food chain, damaging your

health and well-being.

• When replacing old appliances with new ones, the retailer

is legally obligated to take back your old appliance for

disposal at least free of charge.

Service + Support

If your Sun Joe® SPX3001 electric pressure washer requires

service or maintenance, please call the Snow Joe® +

Sun Joe® customer service center at 1-866-SNOWJOE

(1-866-766-9563).

Model + Serial Numbers

When contacting the company, reordering parts, or arranging

service from an authorized dealer, you will need to provide the

model and serial numbers, which can be found on the decal

located on the housing of the unit. Copy these numbers into

the space provided below.

Fig. 20

Pre-lter

Fig. 21

Inletlter

15º

Fig. 22

Needle clean out tool

Micro-switch

Motor

Capacitor

On/off switch

Power cord

Fig. 23

Record the following numbers from the housing or handle of your

new product:

S P X 3 0 0 1

Model #:

Serial #:

Troubleshooting

• Disconnect the unit from the electrical power supply before carrying out maintenance on the machine or when checking that

its parts are in proper working order.

• The hose must be connected and the water turned on before operating your unit. Failure to do so will damage the pump

motor and void your warranty.

• Total Stop System (TSS) – The motor will shut OFF and remain in standby mode during periods of inactivity, or as soon as the

unit is pressurized. THIS IS NORMAL. Simply squeeze the trigger to restart the pump motor.

• To avoid unnecessary hassles, consult the following table before contacting customer service with any mechanical issues.

Problems Possible Cause Possible Solution

Machine refuses

to start

• Power failure/machine not

plugged into a working receptacle.

• Defective socket.

• Fuse has blown.

• Defective extension cord.

• Check to make sure machine is plugged into

a working outlet.

• Check the power cord and reset the GFCI.

Try a dierent outlet.

• Replace fuse. Switch o any other machines

that are using the same circuit.

• Try the unit without an extension cord.

• Check the hoses and connections are airtight.

• Clean or replace valves/seals.

• Please call the Snow Joe® + Sun Joe® customer

service center at 1-866-SNOWJOE (1-866-766-9563)

for assistance.

• Replace fuse. Switch o other machines using

the same circuit.

• Check that the mains voltage corresponds to

specication on the model tag.

• Leave the washer for 5 minutes to cool down.

• Clean the nozzle.

• Install a fuse with a higher amp rating than the

amp consumption of the machine. Try the unit

without an extension cord.

• Allow machine to run by holding the trigger until

regular working pressure resumes.

• Check that the water supply corresponds to the

specications required.

• WARNING! Avoid using long, thin hoses

(minimum 1/2 in. diameter).

• Clean the nozzle.

• Clean the water inlet lter.

• Straighten out the hose to remove any kinks/blockages.

• Please call Snow Joe® + Sun Joe® customer service

center at 1-866-SNOWJOE (1-866-766-9563) for

assistance.

• Wait for pump/hoses or accessories to thaw.

• Connect inlet water.

• Clean the water inlet lter.

• Clean the nozzle.

• Pump sucking air.

• Valves dirty, worn out, or stuck.

• Pump seals worn out.

• Fuse has blown.

• Incorrect mains voltage.

• Thermal sensor activated.

• Nozzle partially blocked.

• Fuse too small.

• Air in inlet hose.

• Inadequate supply of mains water.

• Nozzle partially blocked.

• Water lter blocked.

• Hose kinked.

• Pump/spray gun is leaking.

• Trigger mechanism is broken.

• Pump/hoses or accessories frozen.

• No water supply.

• Water inlet lter blocked.

• Nozzle blocked.

Fluctuating pressure

Machine stops

Fuse blows

Machine pulsating

Machine often starts

and stops by itself

Machine starts, but

no water comes out

Optional Accessories

mWARNING! ALWAYS use only authorized Snow Joe® + Sun Joe® replacement parts and accessories. NEVER use

replacement parts or accessories that are not intended for use with this electric pressure washer. Contact Snow Joe® + Sun Joe®

if you are unsure whether it is safe to use a particular replacement part or accessory with your pressure washer. The use of any

other attachment or accessory can be dangerous and could cause injury or mechanical damage.

25-Foot Medium-duty Extension Hose for

SPX Pressure Washer Series

Solid Brass Universal Quick-Connect Coupler

(Garden Hose to Pressure Washer Adapter)

SPX-25H

SPX-UQC

ModelAccessories Item

Sun Joe® House + Deck All-Purpose Pressure

Washer Rated Concentrated Cleaner SPX-HDC1G

Sun Joe® Premium Snow Foam Pressure

Washer Rated Car Wash Soap + Cleaner SPX-FCS1G

Sun Joe® All-Purpose Heavy Duty Pressure

Washer Rated Cleaner + Degreaser SPX-APC1G

Sun Joe’s complete line of premium pressure washer accessories and attachments

make it easy to get your dirty work done, and also help you get the most out of your model!

SHOP ONLINE now at sunjoe.com

NOTE: Accessories are subject to change without any obligation on the part of Snow Joe® + Sun Joe® to provide notice of such

changes. Accessories can be ordered online at sunjoe.com or via phone by contacting the Snow Joe® + Sun Joe® customer

service center at 1-866-SNOWJOE (1-866-766-9563).

R4_01282020

SNOW JOE® + SUN JOE® CUSTOMER PROMISE

OUR WARRANTY:

Snow Joe warrants new, genuine, powered and non-powered Products to be free from defects in material or workmanship when used

for ordinary household use for a period of two years from the date of purchase by the original, end-user purchaser when purchased

from Snow Joe or from one of Snow Joe’s authorized sellers with proof of purchase. Because Snow Joe is unable to control the quality

of its Products sold by unauthorized sellers, unless otherwise prohibited by law, this Warranty does not cover Products purchased from

unauthorized sellers. If your Product does not work or there’s an issue with a specic part that is covered by the terms of this Warranty,

Snow Joe will elect to either (1) send you a free replacement part, (2) replace the Product with a new or comparable product at no

charge, or (3) repair the Product. How cool is that!

This Warranty gives you speciﬁc legal rights, and you may also have other rights which vary from State to State.

PRODUCT REGISTRATION:

Snow Joe strongly encourages you to register your Product. You can register online at snowjoe.com/register, or by printing and

mailing in a registration card available online from our website, or calling our Customer Service Department at 1-866-SNOWJOE

(1-866-766-9563), or by e-mailing us at [email protected]. Failure to register your Product will not diminish your warranty

rights. However, registering your Product will allow Snow Joe to better serve you with any of your customer service needs.

WHO CAN SEEK LIMITED WARRANTY COVERAGE:

This Warranty is extended by Snow Joe to the original purchaser and original owner of the Product.

WHAT IS NOT COVERED?

This Warranty does not apply if the Product has been used commercially or for non-household or rental applications. This Warranty also

does not apply if the Product was purchased from an unauthorized seller. This Warranty also does not cover cosmetic changes that do

not aect performance. Wearing parts like belts, augers, chains and tines are not covered under this Warranty, and can be purchased

at snowjoe.com or by calling 1-866-SNOWJOE (1-866-766-9563).

ABOVE ALL ELSE, Snow Joe, LLC (“Snow Joe”) is dedicated to you, our customer. We strive to make your experience as pleasant as

possible. Unfortunately, there are times when a Snow Joe®, Sun Joe®, or Aqua Joe® product (“Product”) does not work or breaks under

normal operating conditions. We think it’s important that you know what you can expect from us. That’s why we have a Limited Warranty

(“Warranty”) for our Products.

GUARDE ESTAS INSTRUCCIONES

MANUAL DEL OPERADOR

14.5 A HIDROLAVADORA ELÉCTRICA CON

CARRETE DE MANGUERA

Modelo SPX3001 Forma No. SJ-SPX3001-880S-MR12

Instrucciones originales.

Una división de Snow Joe, LLC

¡IMPORTANTE!

Instrucciones de seguridad

Todos los operadores deberán leer

estas instrucciones antes del uso

m ¡ADVERTENCIA! Esto indica una situación peligrosa,

la cual, de no ser evitada, puede resultar en lesiones severas o

la muerte.

m ¡PRECAUCIÓN! Esto indica una situación peligrosa,

la cual, de no ser evitada, puede resultar en lesiones menores

o moderadas.

m ¡PELIGRO! Esto indica una situación peligrosa, la

cual, de no ser evitada, causará lesiones severas o la muerte.

Seguridad general

m ¡ADVERTENCIA! Este artefacto no está destinado

para su uso por niños o aquellas personas sin asistencia o

supervisión cuyas habilidades físicas, sensoriales o mentales

les impidan usarlo de forma segura. Los niños deben

estar bajo supervisión para asegurar que no jueguen con

el artefacto.

Antes de encender su máquina, por favor verifíquela

cuidadosamente para ver que no tenga defectos. Si

encuentra algún defecto, no la encienda. Contacte a su

concesionario autorizado de Snow Joe® + Sun Joe® o llame

a la central de servicio al cliente de Snow Joe® + Sun Joe® al

1-866-SNOWJOE (1-866-766-9563).

m ¡ADVERTENCIA! Al usar la hidrolavadora eléctrica

se deberán tomar precauciones básicas de seguridad para

reducir riesgos de incendio, choque eléctrico o lesiones

personales.

• Conozca su producto: sepa cómo detener la máquina y

purgar rápidamente la presión. Familiarícese a fondo con

los controles.

• Mantenga alejados a los transeúntes: todos los

visitantes, incluidas las mascotas, deberán estar a una

distancia segura del área de trabajo.

• Use el producto adecuado: no emplee esta máquina para

ningún otro trabajo excepto para el cual está destinada.

• Use ropa adecuada: no use prendas holgadas ni joyería,

ya que pueden llegar a engancharse en las partes móviles.

Se recomienda el uso de guantes de goma protectores

y calzado protector antideslizante cuando se trabaje en

exteriores.

• m ¡PRECAUCIÓN! Tenga cuidado y evite resbalar o caer.

Utilice calzado protector que proteja sus pies y mejore su

posición de pie en supercies resbaladizas.

• Manténgase alerta: fíjese en lo que está haciendo. Utilice

su sentido común. No opere la hidrolavadora si usted

está cansado o bajo la inuencia del alcohol, drogas o

medicamentos.

• No adopte una postura inclinada: mantenga el equilibrio y

posición adecuados en todo momento.

• Evitelosencendidosaccidentales:no lleve la máquina

enchufada con su dedo en el gatillo. Asegúrese de que el

interruptor esté apagado antes de enchufar la máquina.

• No abuse del cable: nunca lleve la máquina por el

cable ni tire bruscamente de éste para desenchufarla del

tomacorriente. Mantenga el cable alejado del calor, aceite y

bordes losos.

• Use gafas protectoras: use también calzado protector,

ropa que se ajuste a su cuerpo, guantes protectores y

protección auditiva y para la cabeza.

• Veriquelatemperaturadelagua:esta hidrolavadora

no está hecha para bombear agua caliente. NUNCA la

conecte a una fuente de agua caliente ya que reducirá

signicativamente el ciclo de vida de la bomba.

• Guárdela en un lugar bajo techo: NUNCA almacene la

hidrolavadora en exteriores o donde pueda congelarse.

La bomba podría dañarse de forma severa.

• Interruptor de circuito de falla de conexión a tierra

(GFCI): se deberá proveer protección en los circuitos

o tomacorrientes a ser usados por esta hidrolavadora.

Los tomacorrientes están disponibles con protección

incorporada GFCI y pueden ser utilizados para esta

medida de seguridad.

• Inspeccioneloscableseléctricos:el aislamiento del

cable de alimentación debe estar perfectamente intacto.

Si el cable de alimentación está dañado o hay señales de

desgaste o deterioro, no use la hidrolavadora. Contacte a

su concesionario autorizado de Snow Joe® + Sun Joe® o

llame a la central de servicio al cliente de Snow Joe® +

Sun Joe® al 1-866-SNOWJOE (1-866-766-9563).

m ¡ADVERTENCIA! No use este artefacto sin antes leer

este manual de instrucciones.

m ¡ADVERTENCIA! Este artefacto ha sido diseñado

para su uso con agentes de limpieza recomendados por el

fabricante. El uso de otros agentes de limpieza o químicos

puede afectar de forma negativa la seguridad del artefacto.

m ¡ADVERTENCIA! No use el artefacto cerca de

personas, a menos que estén usando ropa protectora.

m ¡ADVERTENCIA! Los chorros de alta presión pueden

ser peligrosos si están sujetos a un mal uso. El chorro no

deberá estar dirigido a personas, mascotas, equipos eléctricos

activos, o al artefacto en sí.

• No dirija el chorro hacia usted o demás personas para

limpiar ropa o calzado.

• Riesgo de explosión: no rocíe líquidos inamables.

• Desconecte la herramienta: desconéctela de la

fuente de alimentación antes de llevar a cabo cualquier

mantenimiento.

• Mantenga alejados a los niños: esta hidrolavadora

eléctrica no debe ser usada por niños o personas no

capacitadas.

• Para garantizar la seguridad del artefacto, use solo piezas

de repuesto del fabricante o aprobadas por éste.

m ¡ADVERTENCIA! El agua que ha uido a través de

válvulas contra-reujo se considera como no potable.

m ¡ADVERTENCIA! La máquina deberá estar

desconectada de su fuente de alimentación, es decir

desenchufada del tomacorriente, durante la limpieza,

mantenimiento o reemplazo de las partes.

m ¡ADVERTENCIA! Las mangueras, juntas y

acoplamientos para alta presión son importantes para

la seguridad del artefacto. Use solo mangueras, juntas y

acoplamientos recomendados por el fabricante.

• Veriquelaspartesdañadas:no use el artefacto si hay

daños en el cable de alimentación o en partes importantes;

p. ej., dispositivos de seguridad, mangueras para alta

presión o pistola rociadora.

m ¡ADVERTENCIA! Si se usa un cable de extensión, el

enchufe y tomacorriente deberán ser a prueba de agua.

m ¡ADVERTENCIA! Los cables de extensión

inadecuados pueden ser peligrosos.

• Esta hidrolavadora de alta presión no debe ser usada a

temperaturas menores de 32ºF (0°C).

m ¡ADVERTENCIA! El cable sobre los tanques debe

estar siempre desenrollado por completo para evitar el

sobrecalentamiento.

• Las conexiones de cables de alimentación deben

permanecer secas y por encima del nivel del suelo.

• Si el cable de alimentación está dañado, no utilice el

artefacto. Contacte a su concesionario autorizado de

Snow Joe® + Sun Joe® o llame a la central de servicio al

cliente de Snow Joe® + Sun Joe® al 1-866-SNOWJOE

(1-866-766-9563).

• Mantenga la máquina en una supercie estable y

plana durante la operación, manipulación, transporte y

almacenamiento. Un volcado repentino de la máquina

puede causar lesiones corporales.

• En caso de accidente o desperfecto, desconecte la

hidrolavadora inmediatamente del tomacorriente. Si

usted hace contacto con el detergente, enjuáguese con

abundante agua limpia.

Seguridad eléctrica

ATENCIÓN: si hay problemas con la RED ELÉCTRICA,

pueden ocurrir caídas breves de voltaje al encender el equipo.

Esto a su vez puede afectar otros equipos (como por ejemplo,

el parpadeo de una lámpara). Si la IMPEDANCIA DE LA RED

(Zmax) es menor que 0.335 ohmios, estas uctuaciones no

son esperadas. Si necesita ayuda, puede contactar a su

empresa local de suministro eléctrico para más información.

m ¡ADVERTENCIA! Peligrodechoqueeléctrico:

antes de encender su máquina, por favor inspecciónela

cuidadosamente para ver que no tenga defectos. Si encuentra

algún defecto, no la encienda y contacte a su proveedor.

Se deberá cumplir lo siguiente al conectar la hidrolavadora a la

red eléctrica:

• La conexión al suministro eléctrico deberá haber sido

hecha por una persona calicada.

• La alimentación a este artefacto deberá incluir ya sea un

dispositivo de corriente residual (RCD) que interrumpirá el

suministro si la corriente de fuga a tierra excede los 30 mA

por 30 ms, o un interruptor de circuito a tierra (GFCI).

IMPORTANTE: solo use agua sin impurezas. Si hay un

peligro de arena uida en el agua de entrada (p. ej., de su

propio pozo), se deberá instalar un ltro adicional.

Dispositivos de seguridad

La válvula del descargador puede reducir la presión si ésta

excede los valores predeterminados. La pistola rociadora

incluye un dispositivo de trabado. Cuando este dispositivo

de trabado es activado, la pistola rociadora no puede ser

operada.

1. Sensor térmico: un sensor térmico protege al motor

contra sobrecargas. La máquina se reiniciará luego de

unos cuantos minutos, cuando el sensor térmico se haya

enfriado.

2. Doble aislamiento: en un artefacto de doble aislamiento,

se proporcionan dos sistemas de aislamiento en lugar de

una conexión a tierra. Un artefacto de doble aislamiento

no posee conexión a tierra, y no debe agregársele

La page charge ...

sunjoe SPX3001 Le manuel du propriétaire

Marque: sunjoe

Modèle: SPX3001

Catégorie: Outils de jardin

Taper: Le manuel du propriétaire

Télécharger le PDF

rapport

dans d''autres langues

English: sunjoe SPX3001 Owner's manual
español: sunjoe SPX3001 El manual del propietario

sunjoe SPX3001 Le manuel du propriétaire

sunjoe SPX3001 Le manuel du propriétaire

dans d''autres langues

Documents connexes

Autres documents