Sun Joe GTS4000E Manuel utilisateur

Catégorie
Taille-haies électriques
Taper
Manuel utilisateur
© 2017 by Snow Joe
®
, LLC
All rights reserved. Original instructions.
A Division of Snow Joe
®
, LLC
Model GTS4000E
Form No. SJ-GTS4000E-880E-M
OPERATOR’S MANUAL
SAVE THESE INSTRUCTIONS
LAWN + GARDEN MULTI-TOOL SYSTEM
HEDGE TRIMMER | POLE HEDGE TRIMMER | GRASS TRIMMER | GARDEN TILLER
1
IMPORTANT!
Safety Instructions
All Operators Must Read These
Instructions Before Use
Always follow these safety guidelines. Failure to do so may
result in serious bodily injury or death.
General Safety WARNINGS!
You and any other operator of this power tool must read,
understand, and follow these instructions in their entirety.
Failure to follow these instructions may result in ELECTRIC
SHOCK, FIRE, and/or serious PERSONAL INJURY.
Notice the personal safety alert symbol m used in this
manual to draw your attention to a WARNING given along
with the particular operating instruction. This means that
the operation requires special ATTENTION, CAUTION, and
AWARENESS.
mWARNING! This unit can be dangerous! Careless or
improper use can cause serious injury.
mWARNING! The rotating blades can cut you. Keep
hands and feet away from the blades and the cutting area.
Before using the power tool, familiarize yourself with the
controls, especially how to stop the power tool in an
emergency. The only individuals who should use the power
tool are those who thoroughly understand these instructions
and know how to properly operate the unit. Children should
never be allowed access to the power tool.
Retain this manual for future reference and reread it at the start
of each season.
1. Keep work area clean and well-lit – Cluttered, dark
areas invite accidents.
2. Replacement parts – When servicing this unit, use only
identical replacement parts. Replace or repair damaged
cords immediately.
3. Keep children, bystanders, and pets away – All
spectators, including pets, should be kept a safe distance
away from the work area.
4. Know your product – Know how to start and stop the
machine. Be thoroughly familiar with the controls. Ensure
the controls (start/stop) function properly before using.
5. Use the right tool – Do not use this power tool for any job
except that for which it was intended.
6. Dress properly – Do not wear loose clothing or jewelry as
such articles can become caught in moving parts. Wear
a protective covering to contain long hair. Wearing rubber
gloves and substantial non-slip footwear is recommended
when working outdoors.
7. Extension cords – To prevent electric shock, use only
with an extension cord suitable for outdoor use.
8. Avoid accidental starting – Do not carry the power tool
with your nger on the switch. Make sure the switch is o
before plugging in or unplugging the unit.
mCAUTION! Moving parts will continue to run for several
seconds after turning o the machine.
9. Do not abuse the cord – Never carry the power tool
by the cord or yank the cord to disconnect it from the
receptacle. Keep the cord away from heat, oil, and sharp
edges.
10. Moving parts – Keep hands and feet away from moving
parts. Keep guards in place and in proper working order.
11. Do not force the tool – It will perform better with less
likelihood of personal or mechanical injury if it is used at
the rate for which it was designed.
12. Do not overreach – Keep proper footing and balance at
all times.
13. Use safety glasses – Also use safety footwear, snug-
tting clothing, protective gloves, hearing, and head
protection.
14. Disconnect the tool – Disconnect the power tool from
the power supply when it is not in use, before servicing
it, when changing accessories, and when performing any
other maintenance task.
15. Store idle tool indoors – When not in use, the power tool
should be stored indoors in a dry and high or locked-up
place out of the reach of children.
16. Maintain the power tool with care – Keep the cutting
edges sharp and clean for optimal performance and
to reduce the risk of injury. Inspect the extension cord
periodically and immediately replace it if damaged. Keep
the handles dry, clean, and free from oil and grease.
Follow the additional recommendations described in the
maintenance section of this manual.
17. Avoid dangerous environments – Do not use the power
tool in rain or in damp or wet locations. Do not operate
the power tool in gaseous or explosive atmospheres or
use the power tool near ammable or combustible liquids.
Motors in these tools normally spark, and the sparks
might ignite fumes.
2
18. Stay alert – Watch what you are doing. Use common
sense. Do not operate the power tool when you are
tired or under the inuence of drugs, alcohol, or other
medication.
19. Check for damaged parts – Before further use of the
power tool, a guard or other part that is damaged should
be carefully checked to determine that it will operate
properly and perform its intended function. Check for
alignment of moving parts, binding of moving parts,
breakage of parts, mounting, and any other condition
that may aect its operation. A guard or other part that
is damaged should be properly repaired or replaced.
Contact the Snow Joe
®
+ Sun Joe
®
customer service
center at 1-866-SNOWJOE (1-866-766-9563) for
assistance.
Specic Safety Warnings for Hedge
Trimmer/Pole Hedge Trimmer
1. Remove any adjusting key or wrench before turning
the power tool on. A wrench or key left attached to the
rotating part of the power tool may result in personal
injury.
2. If devices or facilities are available for the extraction and
collection of dust, ensure these are connected or properly
used. Use of these devices can reduce dust related
hazards.
3. Remove any blade that has been damaged. Always make
sure that the blade is installed correctly and securely
fastened before each use. Failure to do so can cause
serious injury.
4. Hold the pole hedge trimmer by insulated gripping
surfaces only, because the cutter blade may contact
hidden wiring or its own cord. Cutter blades contacting a
"live" wire may electrify exposed metal parts of the power
tool and could give the operator an electric shock.
5. Maintain a rm grip on both handles while cutting with the
blade. Keep the blade away from body.
6. Hold pole hedge trimmer properly, e.g., with both hands
if two handles are provided. Loss of control can cause
personal injury.
7. Keep extension cord away from cutting area. During
operation the extension cord may be hidden in shrubs and
can be accidentally cut by the blade.
8. Check the hedge for foreign objects before operation,
e.g., center fences. Take care that the cutting device does
not come in contact with wire or other metal objects.
9. Keep all parts of the body away from the cutting blade.
Do not remove cut material or hold material to be cut
when blades are moving. Make sure the switch is o when
clearing jammed material. A moment of inattention while
operating the pole hedge trimmer may result in serious
personal injury.
10. Carry the hedge trimmer by the handle with the cutting
blade stopped. When transporting or storing the hedge
trimmer always keep the blade covered. Proper handling
of the hedge trimmer will reduce possible personal injury
from the cutter blades.
11. Do not use the hedge trimmer if the switch does not turn it
on and o. Any power tool that cannot be controlled with
the switch is dangerous and must be repaired.
12. Use the pole hedge trimmer and accessories in
accordance with these instructions, taking into account
the working conditions and the work to be performed. Use
of the power tool for operations dierent from intended
use could lead to a hazardous situation.
13. The product should be supplied via a residual current
device (RCD) with a tripping current of not more than
30 mA.
Specic Safety Warnings for
Grass Trimmer
mCAUTION! The safety guard is critical to the safety of
the operator and the safety of people standing within a safe
distance of the grass trimmer. The safety guard keeps the unit
in good working order and must always be in place during
operation. Failure to have the guard in place during operation
is dangerous and will void the warranty.
1. Keep away from the cutting line – It can seriously injure
the skin.
2. Do not try to stop the cutting device with your hands –
Always let it come to a stop by itself.
mCAUTION! The trimmer line spool will continue to rotate
after turning the trimmer OFF. Wait until the trimmer line spool
has completely stopped before making contact.
3. Only use the same type of line originally provided with the
tool.
4. Do not use the unit to cut grass that is not in contact with
the ground.
5. Do not switch the grass trimmer ON in enclosed or poorly
ventilated spaces or in the presence of ammable and/
or explosive substances such as liquids, gases, and
powders.
6. The user of the grass trimmer is responsible for any
damage sustained by third parties that has been caused
by the grass trimmer within the working area.
7. Only cut during broad daylight or with adequate articial
light.
8. Do not cross roads or gravel paths while the unit is still
running.
9. When the grass trimmer is not in use, store it in a dry
place and out of the reach of children.
10. The grass trimmer must be operated in a vertical position,
perpendicular to the ground.
11. Check regularly that all screws are properly secured.
12. Never pass the grass trimmer over the extension cord when
the grass trimmer is in use as this could cut the cord. Make
sure you know where the cord is at all times.
3
13. Never use the grass trimmer when it is raining or when
excessively moist and humid conditions are present. Do not
cut damp grass or leave the tool outside overnight.
14. If the grass trimmer strikes a foreign object or becomes
entangled with it, stop the tool immediately. Unplug it,
check for damage, and have any damage repaired before
proceeding with operation. Do not operate the tool with a
broken hub or spool.
Specic Safety Warnings for
Garden Tiller
1. Always inspect the area where the tiller is to be used.
Remove all objects (e.g., stones, sticks, wires and foreign
objects) that could be thrown by the blades or cause the
operator to trip.
2. Thrown objects can cause serious injury to the eyes and
exposed body. Always wear safety glasses or eye shields
during operation and while performing an adjustment or
repair.
3. Always operate garden tiller wearing adequate garments.
Do not wear jewelry or other loose clothing, which could
become entangled in moving parts. Wear footwear that
provides sure footing.
4. Keep people, pets and property at least 25 feet from the
garden tiller while it is in operation. Stop the garden tiller if
people or pets enter the discharge area.
5. Never attempt to make any adjustments while the motor is
running.
6. Contact with the rotating parts can amputate hands and
feet. Do not put hands or feet near rotating parts.
7. Exercise extreme caution when operating on or crossing
gravel drives, walks, or roads. Stay alert for hidden
hazards or trac.
8. Always plan your culvitating pattern to avoid discharge of
material toward people, pets and property. Thrown objects
can cause serious personal injury.
9. Hold onto the garden tiller with both hands during
operation. Ensure the grips are dry.
10. After striking a foreign object, stop the motor, thoroughly
inspect the garden tiller for any damage, and repair the
damage before restarting and operating the garden tiller.
Disconnect the cord on electric motors.
11. Exercise caution to avoid slipping or falling.
12. Observe any noise-prevention regulations and laws.
13. If the garden tiller should start to vibrate abnormally, stop
the motor and check immediately for the cause. Vibration
is generally a warning sign of trouble.
14. Disengage all controls, stop the motor and wait until
the blades come to a complete stop when leaving the
operating position, before unclogging the blades and
when making any repair, adjustments and inspections.
15. Before cleaning, repairing, or inspecting, shut o the
motor and make certain all moving parts have stopped.
Disconnect the cord on electric motors.
16. Never operate the garden tiller without proper guard,
plates, or other safety protective devices in place.
17. Do not overload the garden tiller capacity by attempting to
cultivate too deep at too fast a rate.
18. Never operate the garden tiller at high transport speeds on
hard or slippery surfaces.
19. Be careful when cultivating in hard ground. The blades
may catch in the ground and propel the garden tiller
forward. If this occurs, let go of the handlebars and do not
restrain the garden tiller.
20. Use extreme caution when reversing or pulling the garden
tiller towards you.
21. Switch on the motor carefully according to instructions
and with feet well away from the blades.
22. Never pick up or carry the garden tiller while the motor is
running.
23. Inspect the garden tiller for worn, missing or damaged
parts and safety labels. See maintenance section for
detailed instructions.
24. Exercise caution when changing direction and operating
on slopes. Always keep feet and legs a safe distance away
from the machine. Look for hidden obstacles or hazards.
25. Do not grasp the exposed cutting blades or cutting edges
when picking up or holding the appliance.
26. Always turn the tiller OFF and disconnect the electrical
power when there is a work stoppage or changing work
areas. Never leave the machine running when unattended.
27. The blades will continue to rotate for a short period after
turning the tiller OFF. Wait until the blades have completely
stopped before lifting the machine or conducting
inspection and maintenance.
28. The motor housing remains hot for a short period after the
machine is turned OFF. Allow the motor housing to cool o
before touching or storing near combustible material.
29. Regularly check the following:
i) Accumulation of debris around the blades could cause
a poor performance or damage to the motor. Inspect
and clean before every use.
ii) Safety devices are operating properly. Do not tamper
with or adjust safety devices.
iii) Bolts and screws for proper tightness. Visually inspect
machine for any damage and that the tiller is in safe
working condition.
iv) Always replace damaged parts with original equipment
manufacturer’s (OEM) parts only. Replacement parts
that do not meet the original equipment specications
may lead to improper performance and compromise
safety.
4
Electric Safety
1. Ground fault circuit interrupter (GFCI) protection should
be provided on the circuit(s) or outlet(s) to be used for
this power tool. Receptacles are available having built-
in GFCI protection and may be used for this measure of
safety.
2. To reduce the risk of electric shock, this appliance has
a polarized plug (i.e. one blade is wider than the other).
Use this appliance only with a polarized UL-, CSA-, or
ETL-listed extension cord recommended for outdoor,
all-weather use.
The appliance plug will t into a polarized extension
cord only one way. If the appliance plug does not t
fully into the extension cord, reverse the plug. If the plug
still does not t, obtain a correct polarized extension
cord. A polarized extension cord will require the use of a
polarized wall outlet. The extension cord plug will t into
the polarized wall outlet only one way. If the plug does
not t fully into the wall outlet, reverse the plug. If the plug
still does not t, contact a qualied electrician to install
the proper wall outlet. Do not modify the appliance plug,
extension cord receptacle, or extension cord plug in any
way.
3. To prevent electric shock, use only with an extension cord
suitable for outdoor use, such as SW-A, SOW-A, STW-A,
STOW-A, SJW-A, SJOW-A, SJTW-A, or SJTOW-A.
Before use, check that the extension cord is in good
condition. When using an extension cord, make sure to
use one heavy enough to carry the current product. For
lengths more than 50 ft (15 m), a No.14 AWG (or greater)
extension cord should be used. An undersized cord will
cause a drop in line voltage resulting in loss of power and
overheating.
4. To prevent the appliance cord from disconnecting from
the extension cord during operation, use the onboard
extension cord restraint hook and/or make a knot with the
two cords as shown in Table 1.
5. Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs with
earthed (grounded) power tools. Unmodied plugs and
matching outlets will reduce risk of electric shock.
6. Avoid body contact with earthed or grounded surfaces,
such as pipes, radiators, ranges and refrigerators. There is
an increased risk of electric shock if your body is earthed
or grounded.
7. If the supply cord is damaged, it must be replaced by an
electrician or a power tool repairer.
8. When operating a power tool outdoors, use an extension
cord suitable for outdoor use. Use of a cord suitable for
outdoor use reduces the risk of electric shock.
9. If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
10. Have your tool repaired by an electrician or a qualied
service center. This power tool complies with relevant
safety requirements. To avoid danger, electrical appliances
must only be repaired by qualied personnel using original
spare parts; otherwise this may result in considerable
damage to the user.
m WARNING m
Electric shock may cause SEVERE INJURY or
DEATH. Heed these warnings:
• Do not allow any part of the power tool to make
contact with water while it is in operation. If the
appliance becomes wet while turned o, wipe dry
before starting.
• Use only a UL-, CSA- or ETL-rated extension cord for
outdoor, all-weather use.
• Do not use an extension cord over 100 ft (30 m).
• Do not touch the appliance or its plug with wet hands
or while standing in water. Wearing rubber boots
oers some protection.
EXTENSION CORD CHART
Extension Cord
Length
Wire Gauge (A.W.G.):
Up to 50 ft
(15 m)
+50 ft - 100 ft
(+15 m - 30 m)
16 14
(B) Connect plug and receptacle
Cord set Appliance cord
(A) Tie cord as shown
Table 1. Method of Securing Extension Cord
5
Double-Insulated Appliances
In a double-insulated appliance, two systems of insulation
are provided instead of grounding. No grounding means is
provided on a double-insulated appliance, nor should a means
for grounding be added to the appliance. Servicing a double-
insulated appliance requires extreme care and knowledge
of the system, and should be performed only by qualied
service personnel at an authorized Snow Joe
®
+ Sun Joe
®
dealer. Replacement parts for a double-insulated appliance
must be identical to the parts they replace. A double-insulated
appliance is marked with the words “Double Insulation” or
“Double Insulated.” The symbol (square within a square)
may also be marked on the appliance.
DOUBLE-INSULATED: GROUNDING NOT
REQUIRED. WHEN SERVICING, USE ONLY
IDENTICAL REPLACEMENT PARTS.
This power tool is double-insulated, eliminating the need for
a separate grounding system. Use only identical replacement
parts. Read the instructions before servicing double-insulated
appliances. Use this electric tool only as described in this
manual.
6
Safety Symbols
The following table depicts and describes safety symbols that may appear on this product. Read, understand, and follow all
instructions on the machine before attempting to assemble and operate.
READ THE OPERATOR'S
MANUAL(S) – Read,
understand and follow all
instructions in the user
manual(s) before attempting to
assemble and operate.
SAFETY ALERT – Indicates
a precaution, a warning or
a danger.
DOUBLE INSULATION – When
servicing, use only identical
replacement parts.
WARNING! Do not expose the
unit to rain or wet conditions.
WARNING! Rotating parts may
cause serious injury. Make sure
the blades come to a complete
stop before transporting the
machine or before inspecting,
cleaning or conducting any
other maintenance.
WARNING! Keep electrical
extension cord away from
blades.
Wear eye protection, breathing
protection and ear protection
(i.e. safety goggles, dust masks
and ear defenders).
SWITCH OFF! Remove plug
from the outlet immediately if
the cord is damaged or cut.
Symbols SymbolsDescriptions Descriptions
SWITCH OFF! Remove plug
from the outlet before cleaning
or conducting maintenance
checks.
Beware of foreign objects
that could be thrown from the
appliance. Keep bystanders a
safe distance away from the
work area.
Wear protective gloves and
non-slip footwear when using
the machine and handling
debris.
DANGER! ROTATING BLADES
Keep hands and feet away
from openings while the
machine is running.
DANGER! Beware of thrown
objects to bystanders. Keep
bystanders at least 15 m (50 ft)
away from the machine.
33 ft
(10 m)
WARNING! SHOCK HAZARD
Keep at least 33 ft (10 m)
away from power lines. Do not
overreach. Keep proper footing
and balance at all times.
7
Know Your Lawn + Garden Multi-Tool System
Read the owner’s manual and safety instructions carefully before operating the hedge trimmer, pole hedge trimmer, grass trimmer
and garden tiller. Compare the illustration below to the power tool in order to become familiar with the location of the various
controls and adjustments. Save this manual for future reference.
Technical Data
Rated Voltage 120 V ~ 60 Hz
Telescoping Pole 3.8 ft to 5.9 ft
(1.16 m to 1.8 m)
Overhead Reach Up to 13 ft (4 m)
Multi-Angle Head -20º, 0º, 20º, 40º, 60º
Hedge Trimmer
Power 4.5 amp
No Load Speed 1600 rpm
Blade Movement Dual-action
Blade Material Rust-resistant steel
Blade Length 19 in. (48 cm)
Cutting Diameter (Max) 0.7 in. (1.8 cm)
Hedge Trimmer Weight 6.2 lbs (2.8 kg)
Pole Hedge Trimmer Weight 9.5 lbs (4.3 kg)
Grass Trimmer
Power 3 amp
Cutting Swath 12 in. (30.5 cm)
Spool Length 26.3 ft (8 m)
No Load Speed 7500 rpm
Spool Advance Auto-feed
Line Diameter 0.063 in. (1.6 mm)
Trimmer Weight 7 lbs (3.2 kg)
Garden Tiller
Power 3.5 amp
No Load Speed 300 rpm
Rotor 4 steel tilling blades
Cultivating Width (Max) 6.1 in. (15.5 cm)
Cultivating Depth (Max) 6 in. (15 cm)
Tiller Weight 11.3 lbs (5.1 kg)
1. Safety lock button
2. Rear handle
3. Appliance cord
4. Cord restraint hook
5. Quick-release button
6. Telescoping pole
7. Auxiliary handle
8. Shoulder strap buckle
9. Shoulder strap
10. Telescoping locking coupler
11. Handle pivot latch
12. Angle adjust button
13. Quick-release button
14. Hedge trimmer cutting head
15. Hand safety switch
16. Hedger safety guard
17. Blade cover
18. Hedge trimmer cutting blade
19. Quick-release button
20. Grass trimmer cutting head
21. Flower guard
22. Trimmer line
23. Spool
24. Trimmer safety guard
25. Quick-release button
26. Garden tiller head
27. Tiller blade
1
7
8
9
10
12
13
11
15
1617
18
19
20
21
22 23
24
25
26
27
14
6
5
2
4
3
8
Unpacking
Carton Contents
Hedge trimmer cutting head with blade cover
• Grass trimmer cutting head with ower guard
Safety guard
Garden tiller head
• Auxiliary handle
• Telescoping pole
• Rear handle
• Manual with registration card
1. Carefully remove the product and any accessories from
the box and check to see that all of the above items are
supplied.
2. Inspect the product carefully to make sure no breakage or
damage occurred during shipping. If you nd damaged or
missing parts, DO NOT return the unit to the store. Please
call the Snow Joe
®
+ Sun Joe
®
customer service center at
1-866-SNOWJOE (1-866-766-9563).
NOTE: Do not discard the shipping carton and packaging
material until you are ready to use the lawn + garden
multi-tool system. The packaging is made of recyclable
materials. Properly dispose of these materials in
accordance with local regulations or save the packaging
for long-term product storage.
IMPORTANT! The equipment and packaging material are
not toys. Do not let children play with plastic bags, foils,
or small parts. These items can be swallowed and pose a
suocation risk!
Pole/Hedge Trimmer
Assembly
Handle Assembly
1. Clamp the auxiliary handle with the telescoping pole using
the 4 screws, as shown (Fig. 1).
Fitting the Hedge Trimmer
1. Insert the rear handle directly into the hedge trimmer
cutting head. When fully inserted, press down the quick-
release button. Make sure the button snaps in rmly and
securely, locking the parts together (Fig. 2).
Converting from Hedge Trimmer to Pole
Hedge Trimmer
1. Lift the quick-release button. Pull to remove the rear
handle from the hedge trimmer cutting head (Fig. 3).
2. Insert the telescoping pole into the hedge trimmer cutting
head. Press down on the quick-release button to lock it
into position (Fig. 4).
3. Insert the rear handle into the end of the telescoping pole
(Fig. 5).
Fig. 1
Telescoping pole
Auxiliary
handle
Clamp
Screws
Clamp
Auxiliary
handle
Fig. 2
Rear handle
Hedge trimmer
cutting head
Quick-release
button
Fig. 3
Rear handle
Hedge trimmer
cutting head
Quick-release
button
Fig. 4
Telescoping pole
Hedge trimmer
cutting head
Quick-release button
9
4. Press down the quick-release button. Ensure the release
button snaps rmly into position to lock the handle
securely (Fig. 5).
5. To convert back to the hedge trimmer, disconnect rear
handle and cutting head from ends of telescoping pole
by lifting the quick-release buttons A and B and pulling
straight out. Then re-insert the rear handle directly into the
hedge trimmer cutting head (Fig. 6).
Attaching the Shoulder Strap
mWARNING! Always attach the shoulder strap from
the unit before starting motor. Use the shoulder strap to help
support the trimmer while in use; do not carry the pole hedge
trimmer with only your hands.
1. Wear the shoulder strap over the left shoulder so that the
hook stays at your right hand side.
2. Fasten the shoulder strap to the buckle on the pole
(Fig. 7).
3. Adjust the length of the strap to attain a comfortable
working position.
mWARNING! The buckle is provided with a means of
quick release which can be accomplished by simply squeezing
the sides of the buckle (Fig. 8).
Operation
Connecting to Power Supply
1. Make a loop in the extension cord and push it up through
the hole in the rear handle and around the cord restraint
hook, then connect the extension cord to the appliance
cord (Fig. 9).
Starting the Pole/Hedge Trimmer
Before operating the pole/hedge trimmer, stand in the
operating position and hold the tool with both hands so that
the cutting blades are always away from your body.
mWARNING! Before you start the tool, make sure the
pole/hedge trimmer is not contacting any object.
mWARNING! You are wearing all of the necessary
personal protective equipment, including protective gloves,
non-slip footwear, safety goggles, ear defenders, and close-
tting clothing.
Fig. 5
Telescoping pole
Rear
handle
Hedge trimmer cutting
head with pole
Quick-release
button
Fig. 6
Telescoping
pole
Rear
handle
Quick-release
button (A)
Quick-release
button (B)
Fig. 7
Buckle
Shoulder strap
Fig. 8
Quick release
buckle
Fig. 9
Rear handle
Cord restraint hook
Extension cord
10
To start the hedge trimmer:
1. Hold the hedge trimmer rmly with both hands. Your right
hand is slightly bent and is holding the rear handle, and
your left hand is straight and is holding the front handle.
2. Press and hold the hand safety switch located on the front
handle (Fig. 10).
3. With your right hand, press and hold safety lock button with
your thumb, then squeeze the on/o trigger switch with
your ngers. Once the tool powers on, you can release the
safety lock button and proceed with operation (Fig. 10).
4. Release the trigger switch and the hand safety switch to
stop the tool.
NOTE: Do not press the trigger switch until you are ready
to make a cut.
To start the pole hedge trimmer:
1. Hold the pole hedge trimmer rmly with both hands. Your
right hand is holding the rear handle and and your left
hand is holding the telescoping pole or auxiliary handle
depending on your preference.
2. Push and hold the safety lock button (located on the rear
handle) with your thumb and then squeeze the trigger
switch with your ngers. Once the tool is running, you can
release the safety lock button (Fig. 11).
3. To turn the tool OFF, release the trigger switch (Fig. 11).
NOTE: Do not press the trigger switch until you are ready
to make a cut.
mWARNING! Blade continues operation after tool is
turned o/trigger released.
Adjusting Pole Hedge Trimmer
Pivoting Head
The pole hedge trimmer head can be rotated into 5 dierent
cutting angles.
1. Always disconnect the pole hedge trimmer from the
power supply.
2. Place the pole hedge trimmer on a sturdy at surface.
3. Press the pivot button and adjust the trimmer head to the
desired angle (Fig. 12).
Extending the Telescoping Pole
The telescoping pole can be extended or shortened for ease
of use.
1. Disconnect the pole hedge trimmer from the power
supply.
2. Unlock the telescoping pole by turning the telescoping
locking coupler clockwise (Fig. 13).
Fig. 10
Front handle
Hand safety
switch
Trigger switch
Safety lock
button
Rear
handle
Fig. 11
Telescoping pole
auxiliary handle
Safety lock button
Rear
handle
Trigger switch
Fig. 12
Pivot button
-20º
20º
40º
60º
Fig. 13
Telescoping
locking
coupler
11
3. Extend the telescoping pole to a comfortable height
(Fig. 14).
NOTE: Push poles toward each other to shorten the pole
or pull them away from each other to lengthen the pole.
Only extend the pole to the minimum length required to
reach the hedges to be trimmed.
4. Lock the pole in position by turning the collar counter-
clockwise, and ensure that the pole is secure.
Cutting Tips
mWARNING! Always hold the pole hedge trimmer with
both hands. Never hold shrubs with one hand and operate
pole hedge trimmer with the other. Failure to heed this warning
can result in serious injury.
mWARNING! Clear the area to be cut before each use.
Remove all objects such as cords, lights, wire, or loose string
which can become entangled in the cutting blade and create a
risk of serious personal injury.
• When operating the pole hedge trimmer, keep the extension
cord behind the pole hedge trimmer. Never drape it over the
hedge being trimmed.
• Do not force the pole hedge trimmer through heavy
shrubbery. This can cause the blades to bind and slow
down. If the blades slow down, reduce the pace.
• Do not attempt to cut stems or twigs that are larger than
3/4 in. thick, or those obviously too large to feed into the
cutting blade. Use a non-powered hand saw or pruning saw
to trim large stems.
• If blades do become jammed, stop the motor, allow the
blades to stop, and disconnect the plug from the power
source before attempting to remove the obstruction.
• If desired, you can use a string to help cut your hedge level.
Decide how high you want the hedge. Stretch a piece of
string along the hedge at the desired height. Trim the hedge
just above the guide line of string. Trim the side of a hedge
so that it will be slightly narrower at the top. More of the
hedge will be exposed when shaped this way, and it will be
more uniform.
• Wear gloves when trimming thorny or prickly growth. When
trimming new growth, use a wide sweeping action, so that
the stems are fed directly into the cutting blade. Older
growth will have thicker stems and will be trimmed easiest
by using a sawing movement.
Using the Pole Hedge Trimmer
• Hold unit rmly with both hands. Always keep your left
hand on the telescoping pole or auxiliary handle and your
right hand on the rear handle. The unit is used for cutting in
either direction in a slow, sweeping action from side to side.
• Stand so that you are stable and balanced on both feet.
• Inspect and clear the area of any hidden objects.
• To protect yourself from electrocution, do not operate within
33 feet (10 m) of overhead electrical lines.
• Never use the pole hedge trimmer near power lines,
fencing, posts, buildings, or other immovable objects.
• Never use a blade after hitting a hard object without rst
inspecting it for damage. Do not use if any damage is
detected.
Cutting Procedures
mWARNING! Never cut near electric cords or power
lines. If the blade jams on any electrical cable, DO NOT
TOUCH THE BLADE. IT CAN CONDUCT ELECTRICITY
AND FATALLY SHOCK YOU! Instead, continue to hold the
hedge trimmer by the insulated rear handle, and lay it down
and away from you in a safe manner. Make sure that electrical
service to the damaged electrical cable is disconnected
before attempting to free the hedge trimmer blade. Contact
with the blade, other conductive parts of the hedge trimmer,
or live electric cords or power lines will result in death by
electrocution or serious injury.
mWARNING! Clear the area to be cut before each use.
Remove all objects such as cords, lights, wire, or loose string
which can become entangled in the cutting blade and create a
risk of electric shock and serious personal injury.
1. When trimming new growth, use a wide sweeping action
so that the stems are fed directly into the blade. Do not try
to cut branches that are thicker than 0.63 in. (16 mm) or
those that are obviously too large to feed into the blade.
Use lopping shears, a hand saw, or a pruning saw to cut
out thick branches rst. If a substantial cut is necessary,
cut a little at a time in several passes. Cut both sides of
the hedge rst and then the top.
2. To perform a horizontal cut, hold the hedge trimmer with
the blade tilted 5-10 degrees to your cutting object; this
makes the operation easier and ensures a better cut
(Fig. 15).
Fig. 14
12
3. To perform a vertical cut, start trimming at the bottom and
sweep up for even cutting. Swing the blades in an arc
towards the outsides of the hedge so that the cuttings are
swept on the ground (Fig. 16).
4. To use the pole hedge trimmer for trimming tall, hard-to-
read hedges or shrubs, hold the trimmer at the position
shown below (Fig. 17). Pivot the power head to several
dierent positions to shape or sculpt shrubs or hedges.
5. To use pole hedge trimmer for trimming the bottoms and
sides of hedges and shrubs, hold the pole trimmer at the
position shown below (Fig. 18).
6. To use pole hedge trimmer for trimming low-lying foliage
or ground cover, hold the pole hedge trimmer at the
position as shown below (Fig. 19).
mCAUTION! Do not use the pole hedge trimmer for
cutting stems greater than 0.70" (1.8 cm) (or approximately
3/4 in. thick).
Use the pole hedge trimmer only for cutting normal shrubbery
found around houses and buildings.
Do not force the pole hedge trimmer through dense growth.
A slight back and forth sawing action may ease the cutting of
larger, more dense growth. If the pole hedge trimmer begins to
slow down, reduce the rate of speed at which you are trying to
cut. If the pole hedge trimmer becomes jammed, immediately
turn the trimmer o. Disconnect the plug from the power
source and clear the jammed debris from the cutter blades.
Fig. 15
5º – 10º
Fig. 16
Fig. 17
Fig. 18
Fig. 19
13
Care + Maintenance
mATTENTION! Before performing any cleaning or
maintenance, disconnect the unit from the power supply.
Never touch the moving blades.
mWARNING! Never spray or clean the hedge shears with
water.
1. Clean the hedge trimmer with a dry towel, particularly
the ventilation slits, after each use, or use a brush in the
event of heavy soiling. Spray the blades with lightweight
machine oil after each use.
2. Store the pole/hedge trimmer in the blade cover provided
and in a dry location out of the reach of children.
3. When servicing, use only identical replacement parts. Use
of any other parts can create a hazard or cause product
damage. Please contact an authorized Snow Joe
®
+
Sun Joe
®
dealer or call the Snow Joe
®
+ Sun Joe
®
customer service center at 1-866-SNOWJOE
(1-866-766-9563) for all replacement parts and
accessories for your product.
Lubricate the Blades
For easier operation and longer blade life, lubricate the hedge
trimmer blade before and after each use.
1. Stop the motor and disconnect the unit from the power
supply.
2. Lay the pole/hedge trimmer on a at surface. Apply
lightweight machine oil along the edge of the top blade
(Fig. 20). If you will be using the pole/hedge trimmer for an
extended period, it is advisable to stop work intermittently
in order to re-oil the blade.
NOTE: Do not oil while the pole/hedge trimmer is running.
Sharpening the Blades
The blade must be re-sharpened if cutting performance and
behavior begin to deteriorate (i.e. if blades frequently snag on
branches).
1. Stop the motor and disconnect the unit from the power
supply. Clamp the blade in a vise.
2. File the exposed cutting surface of each blade tooth with
a smooth round le. Be sure to retain the original angle of
the tooth when ling.
3. Remove the blade from the vise, and power on the motor
until the unsharpened edges of the remaining blade teeth
are exposed.
4. Disconnect the pole/hedge trimmer from the power supply
and repeat the sharpening procedure as necessary.
mWARNING! Do not operate the pole/hedge trimmer with
dull or damaged cutting blades. This may cause overload and
will give unsatisfactory cutting results.
Cleaning the Hedge Trimmer
1. Stop the motor and disconnect the unit from the power
supply.
2. Clean dirt and debris from the body of the pole/hedge
trimmer using a damp cloth and mild detergent.
NOTE: Do not use any strong detergents on the plastic
housing or the handle. These parts can be damaged by certain
aromatic oils such as pine and lemon, and by solvents such as
kerosene.
Storage
1. Always place the blade cover on the blade before storing
or transporting the pole/hedge trimmer. Use caution to
avoid the sharp teeth of the blade.
2. Clean the pole/hedge trimmer thoroughly before storing.
Store the hedge trimmer indoors, in a dry place that is
inaccessible to children. Keep away from corrosive agents
such as garden chemicals and de-icing salts.
Fig. 20
14
Troubleshooting
Most diculties are easy to x. Consult the troubleshooting table for common problems and their solutions. If you continue
to experience problems or need repairs beyond these minor adjustments, please call 1-866-SNOWJOE (1-866-766-9563) for
assistance.
Troubleshooting Table
Possible Cause
• Extension cord not connected to the
power plug
• Extension cord not connected to
power source
• Hand safety switch not fully
engaged
• Dry, corroded blades
• Blades or blade support bent
• Bent or damaged teeth
• Loose blade bolts
Problem
• Unit does not run
• Slow running, noisy, or hot blades
Possible Solution
• Check extension cord is fully
connected to tool
• Check extension cord is fully
connected to a live receptacle
• Check safety switch is fully
depressed prior to pressing trigger
switch
• Lubricate blades
• Straighten blade or blade support
• Straighten teeth
• Tighten blade bolts
15
Grass Trimmer
Assembly
mWARNING! Do not connect to power supply until
assembly is complete. Failure to comply could result in
accidental starting and possible serious personal injury.
Handle Assembly
1. Clamp the auxiliary handle with the telescoping pole using
the 4 screws, as shown (Fig. 21).
Fitting the Safety Guard
mWARNING! The guard must be properly installed. The
guard provides the operator and other bystanders with some
protection from thrown objects.
1. Place the safety guard on the trimmer cutting head and
align the mounting groove (Fig. 22).
2. Firmly press the safety guard into place and secure it to
the trimmer head with the two screws provided (Figs. 23).
NOTE: Never use the tool unless the safety guard is properly
tted.
3. Make sure to remove the cutter guard cover from the line
cutter before using (Fig. 24).
Fitting the Grass Trimmer
1. Insert the telescoping pole into the grass trimmer cutting
head. Press down on the quick-release button to lock it
into position (Fig. 25).
Fig. 21
Telescoping pole
Auxiliary
handle
Clamp
Screws
Clamp
Auxiliary
handle
Fig. 22
Safety guard
Screw
Grass trimmer
Cutting head
Fig. 23
Screws
Fig. 24
Cutter guard
Fig. 25
Telescoping pole
Grass trimmer
cutting head
Quick-release
button
16
2. Insert the rear handle into the end of the telescoping pole
(Fig. 26).
3. Press down the quick release button. Ensure the release
button snaps rmly into position to lock the handle
securely (Fig. 26).
4. To remove, disconnect rear handle and cutting head from
ends of telescoping pole by lifting the quick release button
and pulling straight out.
Height Adjustment
The telescoping pole can be extended or shortened for ease of
use.
1. Disconnect the grass trimmer from the power supply.
2. Unlock the telescoping pole by turning the telescoping
locking coupler clockwise (Fig. 27).
3. Extend the telescoping pole to a comfortable height
(Fig. 28).
4. Lock the telescoping pole in position by turning the
telescoping locking coupler counter-clockwise.
Attaching the Shoulder Strap
mWARNING! Always attach the shoulder strap from
the unit before starting motor. Use the shoulder strap to help
support the trimmer while in use; do not carry the trimmer with
only your hands.
1. Wear the shoulder strap over the left shoulder so that the
buckle stays at your right hand side.
2. Fasten the shoulder strap to the buckle on the pole
(Fig. 29).
3. Adjust the length of the strap to attain a comfortable
working position.
Fig. 26
Grass trimmer with
telescoping pole assembly
Quick release button
Rear
handle
Fig. 27
Telescoping
locking
coupler
Fig. 28
Fig. 29
Buckle
Shoulder strap
17
mWARNING! The buckle is provided with a means of
quick release which can be accomplished by simply squeezing
the sides of the buckle (Fig. 30).
Operation
Connecting to Power Supply
1. Only connect the electric grass trimmer to a working
120 V outlet using a heavy-duty outdoor extension power
cord.
2. Make a loop in the extension cord and push it up through
the hole in the handle and around the cord restraint hook,
then connect the extension cord to the appliance cord
(Fig. 31).
Starting the Grass Trimmer
Before you start the grass trimmer, make sure the trimmer is
not contacting any object.
1. To turn the grass trimmer ON, press and hold the safety
lock button with your thumb, then squeeze the ON/OFF
trigger switch with your ngers. Once the machine powers
on, you can release the safety button and proceed with
operation (Fig. 32).
Trimming
• Wear non-slip gloves for maximum grip and protection.
• For the best cutting action against walls, fences, and in high
grass, move the grass trimmer slowly so grass is cut with
the tip of the high speed nylon line.
• Avoid dragging the grass trimmer and string spool hub in
contact with the ground.
• Trim only when grass and weeds are dry.
NOTE: As the weather becomes cooler, the tendency for the
nylon line to break becomes greater. DO NOT USE WHEN
TEMPERATURE IS BELOW 50ºF (10ºC).
• Cut tall grass from top down. This will prevent grass from
wrapping around the shaft housing and string head which
may cause damage from overheating.
• If grass becomes wrapped around the string head:
Stop the grass trimmer.
Unplug the grass trimmer.
Remove the grass.
• Hold the grass trimmer with your right hand on the rear
handle and your left hand on the front auxiliary handle. The
grass trimmer should be held at a comfortable position with
the rear handle about hip height.
mWARNING! Always hold the trimmer away from
body. Any contact with the grass trimmer cutting head while
operating can result in serious personal injury.
• The life of your nylon line is dependent upon following
instructions for proper use, as well as what is being cut, and
where the cutting is being done.
Fig. 30
Quick release
buckle
Fig. 31
Appliance cord
Cord restraint hook
Extension cord
Fig. 32
Trigger switch
Safety lock
button
Rear handle
18
mWARNING! Remove stones, loose pieces of wood, and
other objects from the cutting area. The string continues to
rotate for a few seconds after switching o the trimmer. Let the
motor come to a complete stop before resuming operation. Do
not rapidly switch the trimmer o and on.
mCAUTION! Always wear eye protection.
1. Hold the trimmer at an angle of approximately 10 – 30
degrees to the work area (Fig. 33).
2. Slowly swing the trimmer from side to side (Fig. 34).
3. Do not overload your trimmer; instead, take small “bites”
of grass, working from the top to the bottom. This will
keep the machine operating at high speed and will greatly
improve its cutting eciency (Fig. 35).
Edging
1. To convert for maintenance edging, turn OFF and unplug
the tool.
2. To use the edger guide/ ower guard, ip it down from its
stored position (Fig. 36).
3. Push the angle adjusting button and at the same time
use the other hand to turn the rear handle 180 degrees
counter-clockwise and release (Fig. 37). The tool is locked
in edger mode.
4. Rotate the whole unit 180 degrees. The tool is now ready
to be used in edger mode (Fig. 38).
Fig. 33
10º – 30º
Fig. 34
Fig. 35
Fig. 36
Flower guard
Fig. 37
Angle
adjusting
button
Rear
handle
Fig. 38
Rear
handle
Rotate
180º
19
5. Use the edge of the guard as a guide when cutting near
fences and walls (Fig. 39).
6. Move the edger in a backwards direction when trimming
around edges to avoid damage.
mWARNING! Do not trim near electrical wires.
Advancing Lines
NOTE: Your trimmer uses 0.063 in. (1.6 mm) diameter nylon
line to cut grass and weed quickly and easily. In time, the
tip of the nylon line will become worn and the auto-feed
mechanism will automatically feed and trim a fresh length of
line. The cutting line will wear faster if the cutting is done along
sidewalks or other abrasive surfaces or heavier weeds are
being cut.
The grass trimmer is equipped with an auto-feed head.
Bumping the head to try to advance the line will damage
trimmer.
1. With the unit running, release the ON/OFF switch trigger.
2. Wait two seconds, and press the ON/OFF switch trigger.
NOTE: The lines will extend approximately 1/4 in. with each
stop and start of the switch trigger until the lines reach the
length of the safety guard.
3. Resume the trimming + edging.
mWARNING! Do not operate the grass trimmer in a tree,
on a ladder, or on a scaold; this is extremely dangerous.
mWARNING! Do not bump the unit on ground in attempt
to feed line or for any other purpose.
Maintenance
mWARNING! Make sure to unplug your electric grass
trimmer before inspecting its parts.
mWARNING! Always wear protective gloves during
maintenance tasks. Do not carry out maintenance when the
motor is running or hot.
Your trimmer line can dry out over time. To keep your line in
top condition, store spare pre-wound spools or bulk line in
a plastic resealable bag with a tablespoon of water.
Never use water or chemical cleaners to clean your grass
trimmer. Wipe it clean with a dry cloth.
Plastic parts may be cleaned by using mild soap and a
damp rag.
Always store your grass trimmer in a dry place. Do not allow
any liquid to get inside it.
Keep the motor ventilation slots clean.
• If you see some sparks ashing in the ventilation slots, this
is normal and will not damage your power tool.
IMPORTANT! To ensure product safety and reliability, repairs,
maintenance, and adjustments to this power tool should be
performed only with identical replacement parts. Contact your
authorized Snow Joe
®
+ Sun Joe
®
dealer or call the Snow Joe
®
+ Sun Joe
®
customer service center at 1-866-SNOWJOE
(1-866-766-9563) for assistance.
Replacing the Spool + Clearing Jams
and Tangled Lines
mWARNING! Unplug the extension cord from the main
power plug before changing the trimmer line.
mCAUTION! Temporarily replace the line cutter guard to
avoid injury.
1. Press together both release tabs on the line spool cover
and remove the cover by pulling it straight o (Fig. 40).
Fig. 39
Fig. 40
Spool cover
Tab
20
2. Lift and remove the spool out of the hub (Fig. 41) and
clean out any dirt or grass residue.
3. In case of jams or tangled line, unwrap about 6 inches
(15 cm) of line to ensure that it's not damaged.
4. If it appears undamaged, rewind it and hook each line end
through the two slots on each side of the spool (Fig. 42).
This will temporarily prevent the spool from unwinding.
5. Unhook the line from the slot and carefully reinsert through
its respective slot on each side of the hub and gently
press the spool down (Fig. 43).
6. Reinstall the spool cover by depressing the release tabs
into their slots in the hub, and push down until the spool
cover clicks into place (Fig. 44).
7. Remove line cutter guard to resume normal operation.
8. Connect the tool to a power source and turn the tool
on. In a few seconds, you will hear the line being cut
automatically to the proper length.
Winding the Line
NOTE: A dual-line factory wound spool (model GTS4000E-RS-
6PK) is available for easy spool replacement on the GTS4000E
electric grass trimmer. Visit snowjoe.com to purchase this
accessory online. Should you wish to wind the line yourself,
the instructions are provided below. Self-winding, however, is
NOT recommended because if the line is not wound properly
it can cause the trimmer’s auto feed system to malfunction.
For this reason, users are strongly urged to purchase the pre-
wound spool.
1. Unplug the grass trimmer.
2. To remove the spool from the trimmer hub, follow steps
1 and 2 from the section "Replacing the Spool + Clearing
Jams and Tangled Lines" beginning on page 19.
3. Take two lines, each with maximum length of 13.1 ft. (4 m)
and maximum diameter of 0.063 in. (1.6 mm) per slot.
Insert the end of one line in one of the eyes of the spool
and wind on the line according to the indicated direction
of winding. Please make certain that the line is wound on
evenly and tightly (Figs. 45 – 47).
Fig. 41
Spool
Cutter guard
Fig. 42
Spool
Slot
Fig. 43
Hub
Slot
Fig. 44
Spool cover
Cutter guard
Tab
Fig. 45
Eye of the spool
Spool line
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60
  • Page 61 61
  • Page 62 62
  • Page 63 63
  • Page 64 64

Sun Joe GTS4000E Manuel utilisateur

Catégorie
Taille-haies électriques
Taper
Manuel utilisateur

dans d''autres langues