sunjoe SPX3000-XT1 Le manuel du propriétaire

Catégorie
Outils de jardin
Taper
Le manuel du propriétaire
SAVE THESE INSTRUCTIONS
1
EN
Model SPX3000-XT1 Form No. SJ-SPX3000-XT1-880E-MR2
R
OPERATOR’S MANUAL
13A ELECTRIC PRESSURE WASHER
Original instructions.
© 2023 Snow Joe, LLC. All rights reserved.
A Division of Snow Joe, LLC
IMPORTANT!
Safety Instructions
All Operators Must Read These
Instructions Before Use
mWARNING! This indicates a hazardous situation, which,
if not avoided, could result in death or serious injury.
mCAUTION! This indicates a hazardous situation, which,
if not avoided, could result in minor or moderate injury.
mDANGER! This indicates a hazardous situation, which,
if not followed, will result in death or serious injury.
General Safety
mWARNING! This appliance is not intended for use
by children or by unassisted, unsupervised persons whose
physical, sensory or mental capabilities prevent them from
using it safely. Children should be supervised to ensure that
they do not play with the appliance.
Before starting up your machine, please check it carefully for
any defects. If you nd any, do not start up your machine.
Contact your authorized Snow Joe® + Sun Joe® dealer or
call the Snow Joe® + Sun Joe® customer service center at
1-866-SNOWJOE (1-866-766-9563).
mWARNING! When using the pressure washer, basic
safety precautions should always be followed to reduce the
risk of re, electric shock, and personal injury. These include:
Know your product – Know how to stop the machine and
bleed pressure quickly. Thoroughly familiarize yourself with
the controls.
Keep bystanders away – All visitors and pets should be
kept a safe distance away from the work area.
Use the right product – Do not use this machine for any
job except that for which it is intended.
Dress properly – Do not wear loose clothing or jewelry.
They can get caught in moving parts. Protective rubber
gloves and non-slip footwear are recommended when
working outdoors.
mCAUTION! – Exercise caution to avoid slipping or falling.
Wear protective footwear that will protect your feet and
improve your footing on slippery surfaces.
Stay alert – Watch what you are doing. Use common
sense. Do not operate the pressure washer when you are
tired, or under the inuence of alcohol or drugs.
WARNING! Risk of Injection or Injury – Do not direct
discharge stream at persons.
Do not overreach – Keep proper footing and balance at
all times.
• Avoid unintentional starting – Do not carry a plugged-
in machine with your nger on the trigger. Make sure the
switch is o before plugging in the machine.
Do not abuse the cord – Never carry the machine by the
cord or yank the cord to disconnect it from the receptacle.
Keep the cord away from heat, oil, and sharp edges.
Use safety glasses – Also use safety footwear, snug-tting
clothing, protective gloves, hearing and head protection.
Check the water temperature – This pressure washer is not
meant to pump hot water. NEVER connect it to a hot water
supply as it will signicantly reduce the life of the pump.
Store indoors – NEVER store the pressure washer
outdoors or where it could freeze. The pump could be
seriously damaged.
Inspect electrical cables – The insulation of the power cord
should be perfectly intact. If the power cord is damaged or
shows any signs of wear or tear, do not use the pressure
washer. Contact your authorized Snow Joe
®
+ Sun Joe
®
dealer or call the Snow Joe
®
+ Sun Joe
®
customer service
center at 1-866-SNOWJOE (1-866-766-9563).
mWARNING! Do not use this appliance without reading
this instruction manual.
mWARNING! This appliance has been designed for
use with cleaning agents that are recommended by the
manufacturer. The use of other cleaning agents or chemicals
may adversely aect the safety of the appliance.
mWARNING! Do not use the appliance within range of
persons unless they are wearing protective clothing.
mWARNING! High-pressure jets can be dangerous if
subject to misuse. The jet must not be directed at persons,
pets, live electrical equipment, or the appliance itself.
• Do not direct the jet at yourself or others in order to clean
clothes or footwear.
Risk of explosion – Do not spray ammable liquids.
Disconnect the tool – Disconnect from the electrical
power supply before performing any maintenance task.
2
Keep children away – This high-pressure electric
power washer must not be used by children or
untrained personnel.
• To ensure appliance safety, use only original replacement
parts from the manufacturer or those approved by
the manufacturer.
mCAUTION! To prevent damage to the appliance, do not
allow it to operate dry. Before starting the appliance, make
sure that it has proper and stable supply of water.
mWARNING! Water that has owed through backow
preventers is considered to be non-potable.
mWARNING! During cleaning, maintenance or when
replacing parts, the machine must be disconnected from its
power source by removing the plug from the socket outlet.
mWARNING! High-pressure hoses, ttings, and
couplings are important for the safe operation of the appliance.
Use only hoses, ttings, and couplings recommended by
the manufacturer.
Check for damaged parts – Do not use the appliance if
the supply cord or other important parts of the appliance
are damaged (e.g. safety devices, high-pressure hoses,
trigger gun).
mWARNING! If an extension cord is used, the plug and
socket must be of watertight construction.
mWARNING! Inadequate extension cords can be
dangerous.
• This high-pressure electric power washer must not be used
at temperatures below 32ºF (0°C).
mWARNING! Power cords on drums should always be
completely unwound to prevent the cord from overheating.
• Power cord connections should be kept dry and o
the ground.
• If the power cord is damaged, do not use the appliance.
Contact your authorized Snow Joe® + Sun Joe® dealer or
call the Snow Joe® + Sun Joe® customer service center at
1-866-SNOWJOE (1-866-766-9563).
• Keep the machine on a stable, at surface during operation,
handling, transportation, and storage. Sudden overturn of
the machine can cause bodily injury.
• In the event of an accident or breakdown, switch o the
machine immediately. (If contact with detergent occurs,
rinse with an abundance of clean water.)
Electrical Safety
ATTENTION: If there are problems with the electrical
MAINS, short voltage drops may appear when starting the
equipment. This can, in turn, inuence other equipment
(e.g. cause a lamp to blink). If the MAINS-IMPEDANCE Zmax
< 0.335 OHM, such disturbances are not expected. (If you
require assistance, contact your local supply authority for
further information.)
mWARNING! Electrical Shock Hazard – Before starting
up your machine, please check it carefully for any defects. If
you nd any, do not start up your machine and contact your
distributor.
The following should be observed when connecting the
high-pressure electric power washer to the electric supply:
• The electric supply connection should be performed by a
qualied person.
• The electric supply to this appliance should include either
a residual current device that will interrupt the supply if the
leakage current to the earth exceeds 30 mA for 30 ms or a
device that will interrupt the earth circuit (GFCI).
IMPORTANT: Only use water without any impurities. If there
is a risk of running sand into the inlet water (i.e. from your own
well), an additional lter should be installed.
Safety Devices
The unloader valve can reduce pressure if it exceeds preset
values. The spray gun features a locking device. When the lock
is activated, the spray gun cannot be operated.
1. Thermal sensor – A thermal sensor protects the motor
against overloading. The machine will restart after a few
minutes when the thermal sensor has cooled.
2. Double insulation – In a double-insulated appliance, two
systems of insulation are provided instead of grounding.
No grounding means is provided on a double-insulated
appliance, nor should a means for grounding be added
to the appliance. Servicing a double-insulated appliance
requires extreme care and knowledge of the system, and
should be performed only by qualied service personnel at
an authorized Snow Joe® + Sun Joe® dealer. Replacement
parts for a double-insulated appliance must be identical
to the parts they replace. A double-insulated appliance
is marked with the words “Double Insulation” or “Double
Insulated.” The symbol (square within a square) may
also be marked on the appliance.
3. Ground fault circuit interrupter (GFCI) protection – this
product is provided with a Ground Fault Circuit Interrupter
built into the power cord plug. This device provides
additional protection from the risk of electric shock. If
replacement of the plug or cord is needed, use only
identical replacement parts that include GFCI protection.
3
4. It is not recommended to use an extension cord with
this pressure washer. The unit comes standard with a
35 ft GFCI power cable. Using an extension cord may
cause a drop in line voltage resulting in loss of power and
overheating.
Use only extension cords that are intended for outdoor
use. These extension cords are identied by marking
"Acceptable for use with outdoor appliance; store indoors
while not in use". Use only extension cords having an
electrical rating not less than the rating of the product. Do
not use damaged extension cords. Examine extension
cord before using and replace if damaged. Do not
abuse extension cord and do not yank on any cord to
disconnect. Keep cord away from heat and sharp edges.
Always disconnect extension cord from the receptacle
before disconnecting the product from the extension cord.
5. To reduce the risk of electric shock, this appliance has a
polarized plug (i.e. one blade is wider than the other). The
appliance plug will t into a polarized outlet only one way.
If the appliance plug does not t fully into the outlet,
reverse the plug. If the plug still does not t, make sure
that you are using the correct polarized wall outlet. If the
plug still does not t, contact a qualied electrician to
install the proper wall outlet. Do not modify the appliance
plug, power cord receptacle, or power cord plug in
any way.
6. To prevent the appliance cord from disconnecting from the
extension cord during operation, make a knot with the two
cords as shown in Table 1.
7. Do not abuse the cord. Never pull the pressure washer
by the cord or yank the cord to disconnect it from the
receptacle. Keep the cord away from heat, oil, and
sharp edges.
Risk of Electrocution
• Inspect cord before using.
Do not use if cord is damaged.
• Keep all connections dry and o the ground.
Do not touch plug with wet hands.
Keep cord away from heat and sharp edges.
• Do not spray electrical apparatus and wiring.
Risk of Explosion
• Do not spray ammable liquids.
• Do not use acids, bases, solvents, or any ammable
material in this product. These substances can cause
physical injuries to the operator and irreversible damage to
the machine.
Additional Safety Instructions
• High-pressure: keep clear of nozzle.
• Injection hazard: equipment can cause serious injury if the
spray penetrates the skin.
• Do not point the gun at anyone or at any part of the body.
• In case of skin penetration, seek medical aid immediately.
• Before servicing, cleaning, or removing any parts, shut o
the power and relieve pressure.
• This machine is not suitable for connection to the potable
water mains.
m WARNING m
Electric shock may cause SEVERE INJURY or
DEATH. Heed these warnings:
• Do not allow any part of the electric pressure washer
to make contact with water while it is in operation. If
the appliance becomes wet while turned o, wipe dry
before starting.
• Do not use an extension cord over 25 ft. The
pressure washer comes equipped with a 35 ft power
cable. Combined cord length must not exceed 60 ft.
Any extension cord must be 14-gauge (or heavier) to
safely power the pressure washer.
• Do not touch the appliance or its plug with wet hands
or while standing in water. Wearing rubber boots
oers some protection.
EXTENSION CORD CHART
Cord Length:
Min. Wire Gauge (A.W.G.):
25 ft (7.6 m)
14
(B) Connect plug and receptacle
Cord set Appliance cord
(A) Tie cord as shown
Table 1. Method of Securing Extension Cord
4
Product Description
Purpose
• This high-pressure electric power washer is intended for
residential use to clean vehicles, machines, buildings,
facades, etc.
Areas of Application
• Never use the machine in potentially explosive areas under
any circumstances!
• The operating temperature must be between 32ºF (0ºC) and
104ºF (40ºC).
The machine consists of an assembly with a pump, which is
encased in a shock-absorbing housing. To provide the operator
with an optimal working position, the machine is equipped with
a stainless steel lance and a non-slip handle grip, whose shape
and conguration comply with applicable regulations.
• Do not cover or modify the stainless steel lance or the spray
nozzles in any way.
• The high-pressure electric power washer is designed to be
used with cold or lukewarm water; higher temperatures can
damage the pump.
• Do not use water that is dirty, gritty, or contains any
chemical products, as these could impair operation and
shorten the life of the machine.
5
Safety Symbols
The following table depicts and describes safety symbols that may appear on this product. Read, understand, and follow all
instructions on the machine before attempting to assemble and operate.
To reduce the risk of injury, user
must keep all bystanders at least
49 ft (15 m) away.
Sound power level is 96 dB(A).
Always keep the power cable
away from heat sources, oils, or
sharp edges. Immediately remove
plug from the mains if the cable is
damaged, frayed, or entangled.
READ THE OPERATOR'S
MANUAL(S) – Read, understand,
and follow all instructions in the
user manual(s) before attempting
to assemble and operate.
SAFETY ALERT – Indicates a
precaution, a warning, or a danger.
WEAR EYE AND HEARING
PROTECTION – For protection
against injury, wear ear defenders
and safety goggles.
Double Insulation – When servicing,
use only identical replacement parts.
WARNING! Do not expose the
unit to rain or wet conditions.
Keep dry.
Machine not suitable for connection
to the potable water mains.
WARNING! Electrical shock hazard.
WARNING! Turn the machine OFF
and disconnect it from the power
supply before inspecting, cleaning,
changing accessories, or conducting
any other maintenance task.
Symbols SymbolsDescriptions Descriptions
Wear non-slip footwear that will
protect your feet and improve your
footing on slippery surfaces.
Wear safety gloves during
use to protect hands.
Store indoors. Never store the
pressure washer outdoors.
If the pump freezes, permanent
damage may result.
6
Know Your Electric Pressure Washer
Read the owner’s manual and safety instructions carefully before operating the electric pressure washer. Compare the illustration
below to the electric pressure washer in order to familiarize yourself with the location of the various controls and adjustments.
Save this manual for future reference.
1. Trigger gun
2. Trigger
3. Safety lock
4. High-pressure hose connection
5. Trigger gun holder
6. Stainless steel lance
7. Wheel (2)
8. Spray wand protector
9. Garden hose adapter (female
coupler)
10. Power cord with GFCI
11. On/O switch
12. Hose holder
13. Detergent bottle with foam cannon
14. Transport handle
15. Onboard storage for Quick-Nozzles
16. Cord holder
17. Water outlet (high-pressure
connection)
18. Needle clean-out tool
19. 0º Quick-Connect nozzle (red)
20. 15º Quick-Connect nozzle (yellow)
21. 25º Quick-Connect nozzle (green)
22. 40º Quick-Connect nozzle (gray)
23. High-pressure hose
24. Wheel + rim brush
25. Utility bristle brush
26. Transfer adapter
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19202122
23
24 25 26
7
Technical Data
Rated Voltage ......................................................120V ~ 60 Hz
Motor ............................................................................ 13-amp
Max Water Inlet Temperature ................................. 104ºF/40ºC
Max Water Inlet Pressure ............................................ 0.7 MPa
Rated Pressure ........................................................... 1700 PSI
Rated Flow ................................................................. 1.2 GPM
Steel-reinforced ......................................................... 20 ft (6 m)
High Pressure Hose Length
Detergent Bottle Capacity .................................. 33.8  oz (1 L)
Power Cord Length ................................ 35 ft (GFCI Protected)
Net Weight ..................................................... 28.4 lbs (12.9 kg)
Unpacking
Carton Contents
Electric pressure washer
Transport handle
Trigger gun
Stainless steel lance
• Four (4) Quick-Connect nozzles (0º, 15º, 25º, and 40º)
• Detergent bottle with foam cannon
• Wheel + rim brush
• Utility bristle brush
• Transfer adapter
• Four (4) large screws
• Two (2) small screws
Spray wand protector
Trigger gun holder
Hose holder
Needle clean-out tool
High-pressure hose
• Garden hose adapter (female coupler) with two sealing rings
Manual with registration card
1. Carefully remove the pressure washer and check to see
that all of the above items are supplied.
2. Inspect the product carefully to make sure no breakage or
damage occurred during shipping. If you nd damaged or
missing parts, DO NOT return the unit to the store. Please
call the Snow Joe® + Sun Joe® customer service center at
1-866-SNOWJOE (1-866-766-9563).
NOTE: Do not discard the shipping carton and packaging
material until you are ready to use your new electric
pressure washer. The packaging is made of recyclable
materials. Properly dispose of these materials in
accordance with local regulations.
IMPORTANT! The equipment and packaging material are
not toys. Do not let children play with plastic bags, foils,
or small parts. These items can be swallowed and pose a
suocation risk!
mWARNING! Do not connect to power supply until
assembly is complete. Failure to comply could result in
accidental starting and possible serious personal injury.
Assembly
1. Position the washer as CLOSE as possible to the
water supply.
2. The washer must be used on a secure and stable surface
in a standing, upright position (Fig. 1).
3. Slide the trigger gun holder into position (Fig. 2).
4. Slide the transport handle into position and secure it with
4 large screws (Fig. 3).
Fig. 1
Fig. 2
Trigger gun holder
8
5. To assemble the hose holder, slide the holder into position
(Fig. 4) and secure it to the unit with one small screw
(Fig. 5).
6. Click the detergent bottle with foam cannon and the 4
Quick-Connect nozzles in place in front and back of the
nozzle storage board (Figs. 6 - 7).
7. To assemble the spray wand protector, rst snap the tab
into the slot located at the bottom left side of the unit,
and then secure it in place with the remaining small screw
(Fig. 8).
Fig. 3
Transport
handle
Fig. 4
Hose holder
Fig. 5
Screw
Fig. 6
Detergent
bottle with foam
cannon
Nozzle storage
board
Fig. 7
Quick-Connect
nozzles
Nozzle
storage
board
Fig. 8
Spray wand protector Small screw
Slot
Tab
9
8. Fit the stainless steel lance into the trigger gun and rotate
the collar until the two parts are completely locked (Fig. 9).
9. Connect the high-pressure hose to the trigger gun
(Fig. 10).
10. Connect the high-pressure hose to the water outlet on the
washer (Fig. 11).
mWARNING! Keep hose away from sharp objects.
Bursting hoses may cause injury. Examine hoses regularly and
replace if damaged. Do not attempt to mend a damaged hose.
11. Connect the garden hose adapter (female coupler) to
the water inlet of the pressure washer, then thread your
garden hose (male end) into the garden hose adapter
(Fig. 12). The garden hose must have an internal diameter
of at least 13 mm (1/2 in.) and must be reinforced. The
water supply must be at least equal to the washer delivery
capacity.
NOTE: The machine is not suitable for connection to the
potable water main.
mWARNING! The machine is not suitable for connection
to the potable water main.
12. Attach garden hose to water supply (Fig. 13).
mWARNING! The intake water temperature must not
exceed 104ºF/40ºC. The water supply must not exceed
0.7 MPa.
mCAUTION! The washer must only be used with clean
water; use of unltered water containing corrosive chemicals
will damage the washer.
13. Make sure the On/O switch is set to the OFF (0) position
before plugging the unit into the power outlet (Fig. 14).
Fig. 9
Stainless
steel lance
Trigger gun
Collar
High-pressure hose
Trigger gun
Fig. 10
Fig. 11
High-pressure water outlet
(REAR)
High-pressure
hose
Fig. 12 Water inlet
(female coupler)
Garden hose
This end to
water inlet
Garden hose
(male end)
Fig. 13
Connect to water supply
Garden hose
10
14. Check that the electrical supply voltage and frequency
(Volt/Hz) correspond to those specied on the pressure
washer rating plate. If the power supply is correct, you
may now plug the pressure washer into the power outlet
(Fig. 15).
NOTE: The GFCI may need to be reset when rst plugged
into the electric outlet. Press the "Reset" button until the
power light indicator on the GFCI illuminates.
Operation
mIMPORTANT! This pressure washer is equipped with
a micro-switch sensitive to water ow. This Total Stop System
(TSS) senses water ow in the pump. When the trigger is
released, water stops owing through the pump. The TSS then
automatically turns the motor o to protect the pump from
overheating, thus saving energy and prolonging pump life.
1. Turn the water supply tap on completely.
2. Make sure the safety lock is down and in its original
position (Fig. 16), then press the trigger for a few seconds
until water ow is steady. This will allow air to escape and
discharge any residual pressure in the hose.
3. Turn the switch to the ON (I) position to start the pressure
washer (Fig. 17).
Using the Nozzles
Before beginning any cleaning task, determine the best nozzle
for the job. Each of the nozzles has a dierent spray pattern.
The nozzle patterns are 40˚ (for gentle cleaning), 25˚ (for all-
purpose cleaning), 15˚ (for tough jobs), and the 0˚ (for spot
cleaning or hard-to-reach areas).
mCAUTION! NEVER change nozzles without locking the
safety lock on the trigger handle.
mWARNING! High-pressure jets can be dangerous if
subject to misuse. The jet must not be directed at persons,
pets, live electrical equipment, or the appliance itself.
This electric pressure washer is equipped with four (4) Quick-
Connect nozzles that easily snap onto the Quick-Connect
collar of the stainless steel lance.
To connect a nozzle to the stainless steel lance:
1. Turn o the pressure washer and shut o the water supply.
Pull the trigger to release water pressure.
Fig. 14
On/Oswitch
RESET
TEST
Fig. 15
GFCI
Power light
indicator
Reset
Fig. 16 Safety lock
Slot
Trigger
Fig. 17
11
2. Engage the safety lock on the trigger handle by pushing
up on the safety lock until it clicks into the slot (Fig. 18).
3. Snap the desired nozzle onto the Quick-Connect collar
until it clicks into place (Fig. 19).
To disconnect a nozzle from the stainless steel lance once the
cleaning job is complete:
4. Turn o the pressure washer and shut o the water supply.
Pull the trigger to release water pressure.
5. Engage the safety lock on the trigger handle by pushing
up on the safety lock until it clicks into the slot (Fig. 18).
6. Remove the nozzle by placing your hand over the nozzle
while pulling back on the Quick-Connect collar.
mWARNING! Do not make changes to the nozzle while
the trigger is engaged. Doing so could result in damage to the
pressure washer or injury to the user.
Working with Detergents
When cleaning with the pressure washer, some cleaning tasks
can be solved with water alone, but for most tasks cleaning
with detergent allows for more eective dirt removal.
For additional cleaning power, the unit comes equipped with a
detergent spray bottle with foam cannon.
mWARNING! Use only detergents specically designed
for use with pressure washers, such as Sun Joe® HOUSE +
DECK WASH (SPX-HDC1G), Sun Joe® SNOW FOAM AUTO
WASH (SPX-FCS1G), or Sun Joe® HEAVY DUTY CLEANER
(SPX-APC1G). DO NOT USE household detergents, acids,
alkaline solutions, bleaches, solvents, ammable material, or
industrial grade solutions. These could damage the pressure
washer. Many detergents may require mixing prior to use.
Prepare the cleaning solution as instructed on the solution
bottle.
1. Remove the foam cannon from the nozzle storage board.
Remove the foam cannon cap with detergent suction tube
from the bottle.
2. Fill the foam cannon bottle with detergent designed
specically for use with pressure washers (Fig. 20).
3. Recap the foam cannon, and attach it to the stainless
steel lance by snapping it onto the Quick-Connect collar
until it clicks into place (Fig. 21).
4. The foam cannon is featured with a foam-volume
adjustable knob. Follow the instructions as shown to use
the foam-volume adjustable knob (Fig. 22).
Fig. 18
Safety lock
Slot
Fig. 19
Nozzle
“Click”
Quick-Connect collar
Stainless steel lance
Fig. 20
Foam cannon
bottle
Pressure washer
detergent
Fig. 21
Foam cannon
“Click”
Quick-Connect collar
Stainless
steel lance
12
5. Apply detergent from the bottom to the top of the dry
surface to be cleaned. Applying detergent in this manner
will dissolve dirt most eectively.
NOTE: Wetting the surface rst is not recommended as it
dilutes the detergent and reduces its cleaning ability.
mCAUTION! Always test the detergent in an
inconspicuous area before use.
6. Allow the detergent to remain on the surface for a short
time before rinsing with the pressure washer. Do not allow
the detergent to dry on the surface.
mCAUTION! Damage may occur to painted surfaces
if the detergent is allowed to dry on them. Wash and rinse a
small section at a time. Avoid working on hot surfaces or in
direct sunlight.
Rinsing with the Pressure Washer
1. Turn o the pressure washer and shut o the water supply.
2. Pull the trigger to release water pressure.
3. Engage the safety lock on the trigger handle by pushing
up on the safety lock until it clicks into the slot (Fig. 18).
4. Remove the detergent bottle with foam cannon by holding
the bottle while pulling back on the Quick-Connect collar.
5. Select the right nozzle for the job (Fig. 23):
i) The 0º intense-jet nozzle (red) is an extremely powerful
nozzle that delivers a high-pressure, pencil-point jet
stream. It is used to cut heavy dirt deposits in a small,
concentrated area. It is ideal for dissolving stubborn
substances, like tar and grease spots on concrete,
or for removing caked mud from equipment. Use this
nozzle to clean hard-to-reach areas including the
facades of 2-story buildings or the undersides of lawn
mowers and tractors.
NOTE: Care should be used when choosing the
right nozzle to avoid permanently gouging wood or
damaging fragile surfaces.
ii) Use the 15º fan-tip nozzle (yellow) for intense cleaning
jobs on hard surfaces. Applications include stripping
paint, removing oil stains, grease, heavy mildew stains,
and rust from steel. This nozzle should only be used in
areas that can withstand the high-pressure from this
nozzle.
iii) Use the 25º fan-tip nozzle (green) to clean home
siding, brick patios, wood decks, driveways, or
sidewalks. When using this nozzle, test a small area
rst to avoid surface damage.
iv) Use the 40º wide-spray tip nozzle (gray) to clean items
such as cars, trucks, boats, patio furniture, or lawn
equipment.
6. Start at the top of the area to be rinsed and work your way
down, making sure to overlap your strokes.
Fig. 22
Foam-volume
adjustable
knob
15º
25º 40º
Fig. 23
13
mIMPORTANT! NEVER USE:
Bleach, chlorine products, and other corrosive chemicals
Liquids containing solvents (e.g. paint thinners, gasoline,
oils)
Tri-sodium phosphate products
Ammonia products
Acid-based products
These chemicals will harm the unit and will damage the
cleaning surface.
Using the Brush Attachments
This pressure washer is equipped with 2 brush attachments,
a utility brush and a heavy-duty wheel + rim brush. To
connect the brush attachments with the spray gun, follow the
instruction below.
1. Disconnect the stainless steel lance from the trigger gun
by twisting counterclockwise.
2. First connect the transfer adapter by inserting it into the
spray gun and twisting clockwise, as shown (Fig. 24).
3. Take the desired brush attachment and align the two
tabs with the inside of the transfer adapter. Once aligned,
push the brush attachment into the trigger gun, twist
counterclockwise to lock into place (Fig. 25).
NOTE: The brush attachments cannot be attached with
the spray gun without the transfer adapter.
Shutting Down
1. Turn the switch to the OFF (0) position and unplug the
power cord from the outlet.
2. Turn o the water source.
3. Hold the trigger to release water pressure.
4. Disconnect the garden hose from the water inlet on
the unit.
5. Disconnect the high-pressure hose connection on the
trigger gun handle.
6. Release the trigger and engage the gun safety lock.
mWARNING! Turn o the water supply and squeeze the
trigger to depressurize the unit. Failure to do so could result in
personal injury due to discharge of high-pressure water.
Taking a Break
If you are taking a break of ve minutes or more between
cleaning tasks:
1. Engage the gun safety lock (Fig. 18).
2. Turn the switch to the OFF (0) position.
3. Unplug the power cord from the outlet.
Storage
mCAUTION! Always store your pressure washer in a
location where the temperature will not fall below 32ºF (0ºC).
The pump in this machine is susceptible to permanent damage
if it freezes. FREEZE DAMAGE IS NOT COVERED BY THE
WARRANTY.
Store the pressure washer indoors in a dry, covered area
where it is not subject to adverse weather conditions.
It is important to store this product in a frost-free area.
Always empty water from all hoses, the pump, and the
foam cannon before storing.
Fig. 24
Trigger gun
Transfer adapter
Fig. 25
Trigger gun
Transfer adapter
Utility brush
Rim + wheel brush
14
mCAUTION! The use of a pump protector is
recommended to prevent cold weather damage during storage
over the winter months.
Winterizing + Long-Term Storage
If you must store your pressure washer in a location where
the temperature falls below 32ºF (0ºC), you can minimize the
chance of damage to your machine by utilizing the following
procedure:
Disconnect all water connections.
Turn on the machine for a few seconds until the remaining
water in the pump exits. Turn o immediately.
Do not allow the high-pressure hose to become kinked.
Store the machine and accessories in a room that does
not reach freezing temperatures.
Do not store near a furnace or other sources of heat that
may dry out the pump seals.
Operate the pressure washer with non-corrosive/non-toxic
anti-freeze, a pump saver, or a pump protector before
storing for the winter.
mWARNING! Before reusing, completely ush the unit
out with clear water. Anti-freeze products can damage
paintwork, so you must ensure there is no anti-freeze left in the
system before using it again.
Maintenance
mCAUTION! Before working on the pressure washer,
disconnect the plug from the power supply socket.
1. To ensure good performance, check and clean the water
inlet lter (Fig. 26). Remove the pre-lter and water inlet
lter and rinse with warm water to prevent any foreign
matter from clogging the pump (Figs. 27 – 28).
2. Clean the nozzle with the needle clean-out tool provided
(Fig. 29). Remove the stainless steel lance from the gun;
remove any dirt from the nozzle hole and rinse.
3. Remove additional debris by back ushing water through
the nozzle and stainless steel lance. To do this, place the
end of your garden hose (with water running) to the tip
of the nozzle, pushing water and debris out of the back
opening of the nozzle and stainless steel lance.
Fig. 26
Waterinletlter
Garden hose adapter
Pre-lter
Fig. 27
Pre-lter
Fig. 28
Inletlter
15º
Fig. 29
Needle clean-out tool
15
Disposal
Recycling the Washer
Do not dispose of electrical appliances as unsorted
municipal waste. Use separate collection facilities.
Contact your local government agency for information
regarding the collection systems available.
If electrical appliances are disposed of in landlls
or dumps, hazardous substances can leak into the
groundwater and get into the food chain, damaging your
health and well-being.
When replacing old appliances with new ones, the retailer
is legally obligated to take back your old appliance for
disposal free of charge.
Service + Support
If your Sun Joe® SPX3000-XT1 electric pressure washer requires
service or maintenance, please call the Snow Joe® + Sun Joe®
customer service center at 1-866-SNOWJOE (1-866-766-9563).
Model + Serial Numbers
When contacting the company, reordering parts, or arranging
service from an authorized dealer, you will need to provide the
model and serial numbers, which can be found on the decal
located on the housing of the unit. Copy these numbers into
the space provided below.
Record the following numbers from the housing or handle of your
new product:
S P X 3 0 0 0 - X T 1
Model #:
Serial #:
16
Troubleshooting
• Disconnect the unit from the electrical power supply before carrying out maintenance on the machine or when checking that
its parts are in proper working order.
The hose must be connected and the water turned on before operating your unit. Failure to do so will damage the pump
motor and void your warranty.
Total Stop System (TSS) – The motor will shut OFF and remain in standby mode during periods of inactivity, or as soon as the
unit is pressurized. THIS IS NORMAL. Simply squeeze the trigger to restart the pump motor.
• To avoid unnecessary hassles, consult the following table before contacting customer service with any mechanical issues.
Problems Possible Cause Possible Solution
Machine refuses
to start
Power failure/machine not
plugged into a working receptacle.
Defective socket.
Fuse has blown.
Defective extension cord.
Check to make sure machine is plugged into
a working outlet.
Check the power cord and reset the GFCI.
Try a dierent outlet.
Replace fuse. Switch o any other machines
that are using the same circuit.
Try the unit without an extension cord.
Check the hoses and connections are airtight.
Clean or replace valves/seals.
Please call the Snow Joe® + Sun Joe® customer
service center at 1-866-SNOWJOE (1-866-766-9563)
for assistance.
Replace fuse. Switch o other machines using
the same circuit.
Check that the mains voltage corresponds to
specication on the model tag.
Leave the washer for 5 minutes to cool down.
Clean the nozzle.
Install a fuse with a higher amp rating than the
amp consumption of the machine. Try the unit
without an extension cord.
Allow machine to run by holding the trigger until
regular working pressure resumes.
Check that the water supply corresponds to the
specications required.
WARNING! Avoid using long, thin hoses
(minimum 1/2 in. diameter).
Clean the nozzle.
Clean the water inlet lter.
Straighten out the hose to remove any kinks/blockages.
Please call Snow Joe® + Sun Joe® customer service
center at 1-866-SNOWJOE (1-866-766-9563) for
assistance.
Wait for pump/hoses or accessories to thaw.
Connect inlet water.
Clean the water inlet lter.
Clean the nozzle.
Pump sucking air.
Valves dirty, worn out, or stuck.
Pump seals worn out.
Fuse has blown.
Incorrect mains voltage.
Thermal sensor activated.
Nozzle partially blocked.
Fuse too small.
Air in inlet hose.
Inadequate supply of mains water.
Nozzle partially blocked.
Water lter blocked.
Hose kinked.
Pump/spray gun is leaking.
Trigger mechanism is broken.
Pump/hoses or accessories frozen.
No water supply.
Water inlet lter blocked.
Nozzle blocked.
Fluctuating pressure
Machine stops
Fuse blows
Machine pulsating
Machine often starts
and stops by itself
Machine starts, but
no water comes out
17
NOTE: Accessories are subject to change without any obligation on the part of Snow Joe® + Sun Joe® to provide notice of such
changes. Accessories can be ordered online at sunjoe.com or via phone by contacting the Snow Joe® + Sun Joe® customer
service center at 1-866-SNOWJOE (1-866-766-9563).
Sun Joe’s complete line of premium pressure washer accessories and attachments
make it easy to get your dirty work done, and also help you get the most out of your model!
SHOP ONLINE now at sunjoe.com
Optional Accessories
mWARNING! ALWAYS use only authorized Snow Joe® + Sun Joe® replacement parts and accessories. NEVER use
replacement parts or accessories that are not intended for use with this electric pressure washer. Contact Snow Joe® + Sun Joe®
if you are unsure whether it is safe to use a particular replacement part or accessory with your pressure washer. The use of any
other attachment or accessory can be dangerous and could cause injury or mechanical damage.
Spray Tip Set
(Compatible with most
SPX Series Pressure Washers)
25 ft Medium-Duty
High Pressure Extension Hose
(For SPX Pressure Washer Series)
Solid Brass Universal Quick-Connect Coupler
(Garden Hose to Pressure Washer Adapter)
SPX3000-TPS
SPX-25H
SPX-UQC
ModelAccessories Item
1
3
4
2
SPX-HDC1G
SPX-FCS1G
SPX-APC1G
Sun Joe® House + Deck All-Purpose Pressure
Washer Rated Concentrated Cleaner
Sun Joe® Premium Snow Foam Pressure Washer
Rated Car Wash + Cleaner
Sun Joe® All-Purpose Heavy Duty Pressure
Washer Rated Cleaner + Degreaser
1155ºº
SOSOAAPP
2255ºº4400ºº
00ºº
5
3-Pack Pressure Washer Concentrate SPX-ASST3Q
R4_01282020
SNOW JOE® + SUN JOE® CUSTOMER PROMISE
OUR WARRANTY:
Snow Joe warrants new, genuine, powered and non-powered Products to be free from defects in material or workmanship when used
for ordinary household use for a period of two years from the date of purchase by the original, end-user purchaser when purchased
from Snow Joe or from one of Snow Joe’s authorized sellers with proof of purchase. Because Snow Joe is unable to control the quality
of its Products sold by unauthorized sellers, unless otherwise prohibited by law, this Warranty does not cover Products purchased from
unauthorized sellers. If your Product does not work or there’s an issue with a specic part that is covered by the terms of this Warranty,
Snow Joe will elect to either (1) send you a free replacement part, (2) replace the Product with a new or comparable product at no
charge, or (3) repair the Product. How cool is that!
This Warranty gives you specific legal rights, and you may also have other rights which vary from State to State.
PRODUCT REGISTRATION:
Snow Joe strongly encourages you to register your Product. You can register online at snowjoe.com/register, or by printing and
mailing in a registration card available online from our website, or calling our Customer Service Department at 1-866-SNOWJOE
(1-866-766-9563), or by e-mailing us at [email protected]. Failure to register your Product will not diminish your warranty
rights. However, registering your Product will allow Snow Joe to better serve you with any of your customer service needs.
WHO CAN SEEK LIMITED WARRANTY COVERAGE:
This Warranty is extended by Snow Joe to the original purchaser and original owner of the Product.
WHAT IS NOT COVERED?
This Warranty does not apply if the Product has been used commercially or for non-household or rental applications. This Warranty also
does not apply if the Product was purchased from an unauthorized seller. This Warranty also does not cover cosmetic changes that do
not aect performance. Wearing parts like belts, augers, chains and tines are not covered under this Warranty, and can be purchased
at snowjoe.com or by calling 1-866-SNOWJOE (1-866-766-9563).
ABOVE ALL ELSE, Snow Joe, LLC (“Snow Joe”) is dedicated to you, our customer. We strive to make your experience as pleasant as
possible. Unfortunately, there are times when a Snow Joe®, Sun Joe®, or Aqua Joe® product (“Product”) does not work or breaks under
normal operating conditions. We think it’s important that you know what you can expect from us. That’s why we have a Limited Warranty
(“Warranty”) for our Products.
18
EN
19
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28
  • Page 29 29
  • Page 30 30
  • Page 31 31
  • Page 32 32
  • Page 33 33
  • Page 34 34
  • Page 35 35
  • Page 36 36
  • Page 37 37
  • Page 38 38
  • Page 39 39
  • Page 40 40
  • Page 41 41
  • Page 42 42
  • Page 43 43
  • Page 44 44
  • Page 45 45
  • Page 46 46
  • Page 47 47
  • Page 48 48
  • Page 49 49
  • Page 50 50
  • Page 51 51
  • Page 52 52
  • Page 53 53
  • Page 54 54
  • Page 55 55
  • Page 56 56
  • Page 57 57
  • Page 58 58
  • Page 59 59
  • Page 60 60

sunjoe SPX3000-XT1 Le manuel du propriétaire

Catégorie
Outils de jardin
Taper
Le manuel du propriétaire