Glo-Ray®
Heated Glass Merchandisers
Vitrines chauffantes
GR3SDH and GR3SDS Series/Série
Installation and Operating Manual
Manuel d’installation et d’utilisation
hatcocorp.com
Register Online!
(see page 2)
S’inscrire en ligne!
(voir page 17)
Do not operate this equipment unless you
have read and understood the contents
of this manual! Failure to follow the
instructions contained in this manual
may result in serious injury or death.
This manual contains important safety
information concerning the maintenance,
use, and operation of this product. If
you’re unable to understand the contents
of this manual, please bring it to the
attention of your supervisor. Keep this
manual in a safe location for future
reference.
English = p 2
WARNING
No opere este equipo al menos que haya
leído y comprendido el contenido de este
manual! Cualquier falla en el seguimiento
de las instrucciones contenidas en
este manual puede resultar en un serio
lesión o muerte. Este manual contiene
importante información sobre seguridad
concerniente al mantenimiento, uso y
operación de este producto. Si usted
no puede entender el contenido de
este manual por favor pregunte a su
supervisor. Almacenar este manual en
una localización segura para la referencia
futura.
ADVERTENCIA
Ne pas utiliser cet équipement sans avoir
lu et compris le contenu de ce manuel ! Le
non-respect des instructions contenues
dans ce manuel peut entraîner de
graves blessures ou la mort. Ce manuel
contient des informations importantes
concernant l’entretien, l’utilisation et le
fonctionnement de ce produit. Si vous ne
comprenez pas le contenu de ce manuel,
veuillez le signaler à votre supérieur.
Conservez ce manuel dans un endroit
sûr pour pouvoir vous y référer plus tard.
Français = p 17
AVERTISSEMENT
P/N 07.04.370.00 © 2020 Hatco Corporation
Form No. GR3SDM-0920
2
English
This manual provides the installation, safety, and operating
instructions for Heated Glass Merchandising Warmers. Hatco
recommends all installation, operating, and safety instructions
appearing in this manual be read prior to installation or operation
of the unit.
Safety information that appears in this manual is identified by
the following signal word panels:
WARNING
WARNING indicates a hazardous situation which, if not
avoided, could result in death or serious injury.
CAUTION
CAUTION indicates a hazardous situation which, if not
avoided, could result in minor or moderate injury.
NOTICE
NOTICE is used to address practices not related to
personal injury.
INTRODUCTION
The Hatco Glo-Ray® Heated Glass Merchandising Warmers,
GR3SDH (Horizontal Shelf) and GR3SDS (Slant Shelf) are
perfect for holding hot wrapped or boxed foods on a buffet
line or customer serving points. A thermostatically controlled,
hardcoated heated base and unique patented heated glass
shelf hold hot wrapped or boxed food products and keep them
at optimum serving temperatures while maintaining product
quality.
These warmers offer an additional heated shelf on the top,
ideal for use of short term holding of food for which serving
temperature is not critical. The Glo-Ray Heated Glass
Merchandising Warmers are guaranteed against breakage
and burnout for one year. These units also feature LED display
lights along with a cord and plug set.
Hatco Glo-Ray Heated Glass Merchandising Warmers are
products of extensive research and field testing. The materials
used were selected for maximum durability, attractive
appearance, and optimum performance. Every unit is inspected
and tested thoroughly prior to shipment.
Important Owner Information ..............................................2
Introduction ...........................................................................2
Important Safety Information ..............................................3
Model Description ................................................................4
All Models ............................................................................ 4
GR3SDH Models ................................................................. 4
GR3SDS Models .................................................................4
Model Designation ...............................................................4
Specifications .......................................................................5
Plug Configurations .............................................................5
Electrical Rating Charts ....................................................... 5
Dimensions .......................................................................... 7
Installation .............................................................................9
General ................................................................................ 9
Operation .............................................................................10
General .............................................................................. 10
Control Panel .....................................................................10
Operating the Unit .............................................................10
Maintenance ........................................................................ 11
General .............................................................................. 11
Daily Cleaning ................................................................... 11
Ground Fault Circuit Interrupters ....................................... 11
Removing Optional Flip-Up Doors .....................................12
Troubleshooting Guide ......................................................13
Options and Accessories ..................................................14
Limited Warranty ................................................................16
Authorized Parts Distributors ...........................Back Cover
IMPORTANT OWNER INFORMATION
Record the model number, serial number, voltage, and purchase
date of the unit in the spaces below (specification label located
on the rear of the unit). Please have this information available
when calling Hatco for service assistance.
Model No. ________________________________________
Serial No. _________________________________________
Voltage ___________________________________________
Date of Purchase ___________________________________
Register your unit!
Completing online warranty registration will prevent delay in
obtaining warranty coverage. Access the Hatco website at
www.hatcocorp.com, select the Support pull-down menu,
and click on “Warranty”.
Business
Hours: 7:00 to 5:00 Monday–Friday,
Central Time (CT)
(Summer Hours: June to September—
7:00 to 5:00 Monday–Thursday
7:00 to 4:00 Friday)
Telephone: 800-558-0607; 414-671-6350
E-mail: [email protected]
24 Hour 7 Day Parts and Service
Assistance available in the United States
and Canada by calling 800-558-0607.
Additional information can be found by visiting our web site at
www.hatcocorp.com.
CONTENTS
Form No. GR3SDM-0920 3
English IMPORTANT SAFETY INFORMATION
WARNING
This unit has no “user-serviceable” parts. If service
is required on this unit, contact an Authorized Hatco
Service Agent or contact the Hatco Service Department at
800-558-0607 or 414-671-6350.
CAUTION
BURN HAZARD: Some exterior surfaces on unit will get
hot. Use caution when touching these areas.
Locate unit at proper counter height in an area that is
convenient for use. Location should be level to prevent
unit or its contents from falling accidentally and strong
enough to support the weight of the unit and contents.
The National Sanitation Foundation (NSF) requires that
units over 36″ (914 mm) in width or weighing more than
80 lbs. (36 kg) either be sealed to or raised above the
installation surface. If this unit cannot be sealed at the
point of use, 2-1/2″ (64 mm) legs are included to allow for
proper cleaning access below the unit.
Do not move or relocate unit for cleaning. Unit is bulky
and heavy.
NOTICE
Do not lay unit on front or back side. Damage to unit could
occur.
Use non-abrasive cleaners and cloths only. Abrasive
cleaners and cloths could scratch finish of unit, marring its
appearance and making it susceptible to soil accumulation.
IMPORTANT—DO NOT use paper towel or glass cleaner
to clean plastic surfaces such as sneeze guards and
flip-up doors. Paper towel and glass cleaner may scratch
the material. Wipe off plastic surfaces using a soft, clean,
water-dampened cloth.
Do not use food pans, ceramic dishes, or abrasive
materials on heated glass shelf. Scratching of the glass
surface may occur, marring its appearance and making it
susceptible to soil accumulation. Damage to glass surface
or breakage of glass caused by misuse is not covered
under warranty.
Do not slide pans across hardcoat surface, use rough-
bottomed pans, or drop anything on hardcoat surface.
Scratching may occur. Damage to hardcoat surface
caused by misuse is not covered under warranty.
Do not allow the glass shelf to overheat. Overheating may
cause the food containers to melt or soften.
Do not locate unit in area with excessive air movement
around unit. Avoid areas that may be subject to active air
movements or currents (i.e., near exhaust fans/hoods, air
conditioning ducts, and exterior doors).
Clean unit daily to avoid malfunctions and maintain
sanitary operation.
WARNING
ELECTRIC SHOCK HAZARD:
• Plug unit into a properly grounded electrical receptacle
of the correct voltage, size, and plug configuration. If
plug and receptacle do not match, contact a qualified
electrician to determine and install proper voltage and
size electrical receptacle.
• Turn OFF power switch, unplug power cord, and allow
unit to cool before performing any cleaning, setup, or
maintenance.
• Units with two power cords must have both power
supply cords disconnected before performing any
cleaning, adjustments, or maintenance.
• DO NOT submerge or saturate with water. Unit is not
waterproof. Do not operate if unit has been submerged
or saturated with water.
• Unit is not weatherproof. Locate unit indoors where
ambient air temperature is a minimum of 70°F (21°C).
• Do not steam clean or use excessive water on unit.
• This unit is not “jet-proof” construction. Do not use
jet-clean spray to clean this unit.
• Do not clean unit when it is energized or hot.
• Do not pull unit by power cord.
• Discontinue use if power cord is frayed or worn.
• Do not attempt to repair or replace a damaged power
cord. Cord must be replaced by Hatco, an Authorized
Hatco Service Agent, or a person with similar
qualifications.
• This unit must be serviced by qualified personnel only.
Service by unqualified personnel may lead to electric
shock or burn.
• Use only Genuine Hatco Replacement Parts when
service is required. Failure to use Genuine Hatco
Replacement Parts will void all warranties and may
subject operators of the equipment to hazardous
electrical voltage, resulting in electrical shock or burn.
Genuine Hatco Replacement Parts are specified to
operate safely in the environments in which they are
used. Some aftermarket or generic replacement parts
do not have the characteristics that will allow them to
operate safely in Hatco equipment.
FIRE HAZARD: Install unit with a minimum of 3″ (76 mm) of
space from rear of unit to a back wall. If safe distances are
not maintained, discoloration or combustion could occur.
Make sure food product has been heated to the proper
food-safe temperature before placing in unit. Failure to
heat food product properly may result in serious health
risks. This unit is for holding pre-heated food product only.
Do not place food product directly onto hardcoat surface.
Food product must be wrapped, boxed, or on a food pan.
Make sure all operators have been instructed on the safe
and proper use of the unit.
This unit is not intended for use by children or persons
with reduced physical, sensory, or mental capabilities.
Ensure proper supervision of children and keep them
away from the unit.
Read the following important safety information before using this equipment to avoid serious
injury or death and to avoid damage to equipment or property.
Form No. GR3SDM-0920
4
English
MODEL DESCRIPTION
MODEL DESIGNATION
All Models
All GR3SD Models feature a thermostatically controlled
hardcoated heated base and glass dual heat source which
conducts heat upward to keep the food on the glass shelf
warm, and radiates heat downward to blanket the product
below. Units also include tempered glass side panels, product
divider rods, LED display lights, and a cord and plug set.
GR3SDH Models
The GR3SDH Models are horizontal shelf warmers designed
to hold hot wrapped or boxed food product.
or dual heated glass shelf.
Ground
Fault
Circuit
Interrupter
Hardcoated
Heated
Base
Control
Panel
Glass
Side
Panel
Heated Glass
Shelf
Power
On/Off
Switch
GR3SDH Models
GR3SDS Models
The GR3SDS Models are slant shelf warmers designed to hold
hot wrapped or boxed food product. The shelves are slanted for
convenience of self-serve.
or dual heated glass shelf.
Ground
Fault
Circuit
Interrupter
Hardcoated
Heated
Base
Heated Glass
Shelf
Control
Panel
Glass
Side
Panel
Power
On/Off
Switch
GR3SDS Models
NOTE: Sneeze guards and flip-up doors are available for all
units. Refer to the OPTIONS AND ACCESSORIES
section in this manual for details.
G R 3 S D H - x x D
Glo-Ray®
Sandwich Display
Heated Glass Shelf
Width of Unit (inches)
No Character = Single Shelf
D = Dual Shelf
H = Horizontal Shelf
S = Slanted Shelf
Form No. GR3SDM-0920 5
English
Model Voltage Watts Amps Plug Configuration Shipping Weight
GR3SDH-27 120 997 8.3 NEMA 5-15P 108 lbs. (50 kg.)
GR3SDH-33 120 1251 10.4 NEMA 5-15P 120 lbs. (55 kg.)
GR3SDH-39 120 1505 12.5 NEMA 5-15P †133 lbs. (60 kg.)
Model Voltage Watts Amps Plug Configuration Shipping Weight
GR3SDH-27D 120 1769 14.7 NEMA 5-15P †147 lbs. (67 kg.)
GR3SDH-33D 120/208240 2227 10.3 NEMA L14-20P •166 lbs. (75 kg.)
GR3SDH-39D 120/208240 2685 12.3 NEMA L14-20P •194 lbs. (88 kg.)
SPECIFICATIONS
Plug Configurations
Units are equipped with an electrical cord and plug appropriate
for the electrical rating of the unit and must be connected to a
dedicated circuit.
WARNING
ELECTRIC SHOCK HAZARD: Plug unit into a properly
grounded electrical receptacle of the correct voltage,
size, and plug configuration. If plug and receptacle do not
match, contact a qualified electrician to determine and
install proper voltage and size electrical receptacle.
NOTE: The specification label is located on the rear of the unit.
See the label for the serial number and verification of
unit electrical information.
NEMA 5-15P NEMA 5-20P
NEMA L14-20P NEMA 14-20P
Plug Configurations
NOTE: Receptacle not supplied by Hatco.
Electrical Rating Chart — GR3SDH-xx Models (Horizontal Single Shelf)
Electrical Rating Chart — GR3SDH-xxD Models (Horizontal Dual Shelf)
† NEMA 5-20P for Canada.
• NEMA 14-20P is optional.
Form No. GR3SDM-0920
6
English
Model Voltage Watts Amps Plug Configuration Shipping Weight
GR3SDS-27D 120 1769 14.7 NEMA 5-15P †164 lbs. (75 kg.)
GR3SDS-33D 120 1272/955 10.6/8.0 NEMA 5-15P *190 lbs. (86 kg.)
120/208240 2227 10.3 NEMA L14-20P •
GR3SDS-39D 120/208240 2685 12.3 NEMA L14-20P •206 lbs. (94 kg.)
Model Voltage Watts Amps Plug Configuration Shipping Weight
GR3SDS-27 120 997 8.3 NEMA 5-15P 115 lbs. (52 kg.)
GR3SDS-33 120 1251 10.4 NEMA 5-15P 127 lbs. (58 kg.)
GR3SDS-39 120 1505 12.5 NEMA 5-15P †156 lbs. (71 kg.)
SPECIFICATIONS
Electrical Rating Chart — GR3SDS-xx Models (Slanted Single Shelf)
Electrical Rating Chart — GR3SDS-xxD Models (Slanted Dual Shelf)
† NEMA 5-20P for Canada.
• NEMA 14-20P is optional.
* Unit is equipped with two cord and plug sets, requiring two separate 120 V, 15 A power circuits (not available for
Canada).
Form No. GR3SDM-0920 7
English
Model
Width
(A)
Depth
(B)
Height
(C)
Footprint
Width (D)
Footprint
Depth (E)
Shelf
Height (F)
GR3SDH-27 27-1/4
(692 mm)
27-1/4
(692 mm)
16-1/8
(410 mm)
25
(635 mm)
25
(635 mm)
7-1/4
(184 mm)
GR3SDH-33 33-1/4
(845 mm)
27-1/4
(692 mm)
16-1/8
(410 mm)
31
(787 mm)
25
(635 mm)
7-1/4
(184 mm)
GR3SDH-39 39-1/4
(997 mm)
27-1/4
(692 mm)
16-1/8
(410 mm)
37
(940 mm)
25
(635 mm)
7-1/4
(184 mm)
GR3SDH-27D 27-1/4
(692 mm)
27-1/4
(692 mm)
25-7/8
(657 mm)
25
(635 mm)
25
(635 mm)
7-1/4
(184 mm)
GR3SDH-33D 33-1/4
(845 mm)
27-1/4
(692 mm)
25-7/8
(657 mm)
31
(787 mm)
25
(635 mm)
7-1/4
(184 mm)
GR3SDH-39D 39-1/4
(997 mm)
27-1/4
(692 mm)
25-7/8
(657 mm)
37
(940 mm)
25
(635 mm)
7-1/4
(184 mm)
SPECIFICATIONS
GR3SDH — Single Shelf
Front View
Side View
GR3SDH — Dual Shelf
F
F
F
EE
DD
A
A
B
B
C
C
Front View
Side View
Dimensions — GR3SDH Models
Form No. GR3SDM-0920
8
English
Model
Width
(A)
Depth
(B)
Height
(C)
Footprint
Width (D)
Footprint
Depth (E)
Shelf
Height (F)
GR3SDS-27 27-1/4
(692 mm)
26-7/8
(683 mm)
20-1/2
(521 mm)
25
(635 mm)
24-1/4
(616 mm)
7-1/4
(184 mm)
GR3SDS-33 33-1/4
(845 mm)
26-7/8
(683 mm)
20-1/2
(521 mm)
31
(787 mm)
24-1/4
(616 mm)
7-1/4
(184 mm)
GR3SDS-39 39-1/4
(997 mm)
26-7/8
(683 mm)
20-1/2
(521 mm)
37
(940 mm)
24-1/4
(616 mm)
7-1/4
(184 mm)
GR3SDS-27D 27-1/4
(692 mm)
26-7/8
(683 mm)
30-1/2
(775 mm)
25
(635 mm)
24-1/4
(616 mm)
7-1/4
(184 mm)
GR3SDS-33D 33-1/4
(845 mm)
26-7/8
(683 mm)
30-1/2
(775 mm)
31
(787 mm)
24-1/4
(616 mm)
7-1/4
(184 mm)
GR3SDS-39D 39-1/4
(997 mm)
26-7/8
(683 mm)
30-1/2
(775 mm)
37
(940 mm)
24-1/4
(616 mm)
7-1/4
(184 mm)
SPECIFICATIONS
GR3SDS — Single Shelf
Front View
Side View
GR3SDS — Dual Shelf
Front View
Side View
A
A
B
B
D D
C
C
EE
FF
F
Dimensions — GR3SDS Models
Form No. GR3SDM-0920 9
English INSTALLATION
General
Glo-Ray® Heated Glass Merchandisers are shipped with most
components pre-assembled. Care should be taken when
unpacking shipping carton to avoid damage to the unit and
components enclosed.
WARNING
ELECTRIC SHOCK HAZARD: Unit is not weatherproof.
Locate unit indoors where ambient air temperature is a
minimum of 70°F (21°C).
FIRE HAZARD: Install unit with a minimum of 3″ (76 mm) of
space from rear of unit to a back wall. If safe distances are
not maintained, discoloration or combustion could occur.
CAUTION
Locate unit at proper counter height in an area that is
convenient for use. Location should be level to prevent
unit or its contents from falling accidentally and strong
enough to support the weight of the unit and contents.
NOTICE
Do not lay unit on front or back side. Damage to unit could
occur.
NOTE: Due to the size and weight of Heated Glass
Merchandisers, installation of a unit will require two or
more people.
1. Remove the unit from the carton.
NOTE: To prevent delay in obtaining warranty coverage, complete
online warranty registration. See the IMPORTANT
OWNER INFORMATION section for details.
2. Remove tape and protective packaging from all surfaces
of the unit.
procedure below. If installing a countertop mounted unit,
continue to the next step.
a. Remove all channel dividers and product divider rods.
NOTE: The side glass panels are shipped loose. Make sure
they are not installed before tipping unit.
b. Carefully lay unit on its side and remove the four rubber
shipping feet, if installed.
same holes where the four rubber shipping feet were
removed.
d. Remove the two venting panels on both sides of the unit
by removing the four screws.
e. Return unit to the upright position.
2-1/2″ (64 mm) Leg
Vented
Side Panel
(remove)
Screw
Installing the Legs
4. Place the unit in the desired location.
• Locate the unit in an area where the ambient air
temperature is constant and a minimum of 70° F
(21° C). Avoid areas that may be subject to active air
movements or currents (i.e., near exhaust fans/hoods,
air conditioning ducts, exterior doors).
• Make sure the unit is at the proper counter height in an
area convenient for use.
• Make sure the countertop is level and strong enough to
support the weight of the unit and food product.
• Make sure the feet on the bottom of the unit are
positioned securely on the countertop.
5. If installing a countertop mounted unit, apply National
Sanitation Foundation-approved (NSF) silicone around
the perimeter of the unit.
6. Slide each glass side panel into the top channel, then
lower the panel into the bottom channel.
Glass Side Panel angled slightly.
Installing the Glass Side Panels
7. Install the product divider rods into the channel dividers,
if desired. The rods can be adjusted easily to separate
holding areas as needed.
8. Install any accessories that came with the unit. Refer to the
OPTIONS AND ACCESSORIES section for details.
9. Plug the unit into a properly grounded electrical receptacle
of the correct voltage, size, and plug configuration. See the
SPECIFICATIONS section for details.
Form No. GR3SDM-0920
10
English
OPERATION
Shelf Heat Control Knob(s)
The Shelf Heat Control knob(s) controls heat to a glass shelf on
the unit. The heat source icon below the control indicates which
shelf corresponds to the control. Turning a Heat Control knob
clockwise will decrease the temperature setting. Turning a Heat
Control knob counterclockwise will increase the temperature
setting. Turning a Shelf Heat Control knob to “O” turns off heat
to the corresponding shelf.
NOTE: Each heated glass shelf is controlled independently.
Lights On/Off Switch
The Lights On/Off Switch controls power to the lights.
Power On/Off Switch
The Power On/Off Switch controls power to the entire unit.
Operating the Unit
Startup
1. Plug unit into a properly grounded electrical receptacle of
the correct voltage, size and plug configuration. See the
SPECIFICATIONS section for details.
2. Move the Power On/Off switch up to the “on” position.
• The heated base will energize.
• Power to each heated glass shelf and the Lights On/Off
switch is available.
CAUTION
BURN HAZARD: Some exterior surfaces on unit will get
hot. Use caution when touching these areas.
3. Move the Lights On/Off switch to the “on” position. The
display lights will illuminate.
NOTE: The Glo-Ray Heated Glass Merchandiser can be used
with the lights on or off.
4. Turn the Heat Control knobs to the desired temperature
setting for the base and each heated glass shelf. The
operating temperature range is from room temperature to
approximately 185°–200°F (85°–93°C).
5. Allow the unit 30 minutes to reach operating temperature
before placing preheated food product.
Shutdown
1. Move the Power On/Off switch down to the “off” position.
The heated glass shelves, overhead lights, and heated
base will shut off.
2. Perform the “Daily Cleaning” procedure in the
MAINTENANCE section of this manual.
General
Use the following procedures to operate the Glo-Ray® Heated
Glass Merchandisers.
WARNING
Read all safety messages in the IMPORTANT SAFETY
INFORMATION section before operating this equipment.
Do not place food product directly onto hardcoat or glass
surface. Food product must be wrapped, boxed, or on a
food pan.
NOTICE
Do not use food pans, ceramic dishes, or abrasive materials
on heated glass shelf. Scratching of the glass surface may
occur, marring its appearance and making it susceptible to
soil accumulation. Damage to glass surface or breakage
of glass caused by misuse is not covered under warranty.
Do not slide pans across hardcoat surface, use rough-
bottomed pans, or drop anything on hardcoat surface.
Scratching may occur. Damage to hardcoat surface caused
by misuse is not covered under warranty.
Do not allow the glass shelf to overheat. Overheating may
cause the food containers to melt or soften.
Control Panel
The following are descriptions of the controls used to operate
the unit. All controls are located on the control panel at the back
of the unit.
Heat Source Icon
The heat source icon consists of two or three bars and appears
below the control knob for each heat source. Each bar in the
icon represents a heat source on the unit, starting at the base.
The bar that is in red indicates which heat source is controlled
by the corresponding control knob.
Base Heat Control Knob
The Base Heat Control knob controls heat to the base of the unit.
Turning the Base Heat Control knob clockwise will increase
the temperature setting. Turning the Base Heat Control knob
counterclockwise will decrease the temperature setting.
Base Heat Control
Knob
Shelf Heat Control Knobs Lights On/Off Switch
Ground Fault
Circuit Interrupter Power On/Off
Switch
Control Panel
Form No. GR3SDM-0920 11
English MAINTENANCE
General
Hatco Heated Glass Merchandisers are designed for maximum
durability and performance with minimum maintenance.
WARNING
ELECTRIC SHOCK HAZARD:
• Turn OFF power switch, unplug power cord, and allow
unit to cool before performing any cleaning, setup, or
maintenance.
• Units with two power cords must have both power
supply cords disconnected before performing any
cleaning, adjustments, or maintenance.
• DO NOT submerge or saturate with water. Unit is not
waterproof. Do not operate if unit has been submerged
or saturated with water.
• Do not steam clean or use excessive water on unit.
• This unit is not “jet-proof” construction. Do not use
jet-clean spray to clean this unit.
• Do not clean unit when it is energized or hot.
• Use only Genuine Hatco Replacement Parts when
service is required. Failure to use Genuine Hatco
Replacement Parts will void all warranties and may
subject operators of the equipment to hazardous
electrical voltage, resulting in electrical shock or burn.
Genuine Hatco Replacement Parts are specified to
operate safely in the environments in which they are
used. Some aftermarket or generic replacement parts
do not have the characteristics that will allow them to
operate safely in Hatco equipment.
This unit has no “user-serviceable” parts. If service
is required on this unit, contact an Authorized Hatco
Service Agent or contact the Hatco Service Department at
800-558-0607 or 414-671-6350.
CAUTION
Do not move or relocate unit for cleaning. Unit is bulky
and heavy.
Daily Cleaning
To maintain performance and preserve the finish of the Heated
Glass Merchandiser, clean the unit daily.
NOTICE
Clean unit daily to avoid malfunctions and maintain
sanitary operation.
Use non-abrasive cleaners and cloths only. Abrasive
cleaners and cloths could scratch finish of unit, marring its
appearance and making it susceptible to soil accumulation.
IMPORTANT—DO NOT use paper towel or glass cleaner
to clean plastic surfaces such as sneeze guards and
flip-up doors. Paper towel and glass cleaner may scratch
the material. Wipe off plastic surfaces using a soft, clean,
water-dampened cloth.
1. Turn off the unit, unplug the power cord(s), and allow the
unit to cool.
• Units with two power cords must have both power
supply cords disconnected before performing any
cleaning, adjustments, or maintenance.
2. Remove and discard any remaining food product.
3. Wipe down the hardcoated heated base and all metal
surfaces using a clean, damp cloth. Stubborn stains may be
removed with a good non-abrasive cleaner. Hard to reach
areas should be cleaned with a small brush and mild soap.
4. Clean the heated glass shelves and glass side panels using
ordinary glass cleaner and a soft cloth or paper towel.
5. If equipped, clean the plastic sneeze guards or flip-up
doors using soft cleaning cloths, mild soap, and water.
NOTICE: Do not use paper towel or glass cleaner on
plastic surfaces—scratching may occur.
Ground Fault Circuit Interrupters
Heated Glass Merchandisers are supplied with up to two,
built-in Ground Fault Circuit Interrupters (GFCI). GFCIs are
designed to turn off electrical power and help prevent damage
to the internal components when there is a short circuit or
electrical fault.
To reset a GFCI:
1. Make sure the unit is plugged in and all ON/OFF switches
are in the ON position.
2. Push the reset button.
NOTE: The unit must be plugged in and turned on for the GFCI
to reset. If the unit is off, the GFCI will not reset.
If a GFCI continues to trip, contact an Authorized Hatco Service
Agency.
RESET Button
Ground Fault
Circuit Interrupter
Ground Fault Circuit Interrupters
Form No. GR3SDM-0920
12
English
MAINTENANCE
Removing Optional Flip-Up Doors
Use the following procedure to remove flip-up doors for
cleaning.
1. Lift the hinge screw up and out of the open end bracket.
2. With the flip-up door tilted downward slightly, slide the
other hinge screw out of the closed end bracket.
Hinge
Screw
Open
End
Bracket
Closed
End Bracket
Removing Optional Flip-Up Doors
Form No. GR3SDM-0920 13
English
Symptom Probable Cause Corrective Action
Unit is plugged in, but not
working.
Unit not turned on. Move all Power On/Off switches to the “on” position.
Circuit breaker tripped. Reset circuit breaker. If circuit breaker continues to trip,
contact Authorized Service Agent or Hatco for assistance.
GFCI(s) tripped. Reset GFCI. If GFCI continues to trip, contact Authorized
Service Agent or Hatco for assistance.
Power On/Off switch(es) defective. Contact Authorized Service Agent or Hatco for assistance.
Supply voltage to unit is incorrect. Verify supply voltage at both receptacles matches the unit
specifications.
Internal electrical malfunction. Contact Authorized Service Agent or Hatco for assistance.
Display light(s) not
working.
Lights On/Off switch in the “off” position. Move Lights On/Off switch to the “on” position.
Display lights connection loose or defective. Contact Authorized Service Agent or Hatco for assistance.
Base, glass shelf, and/
or canopy heat not hot
enough.
Corresponding Heat Control Knob(s) set too low. Adjust the appropriate Heat Control Knob(s) to a higher
setting.
Excessive air movement around unit. Move the unit or redirect air movement away from the unit.
Heat Control(s) not working properly.
Contact Authorized Service Agent or Hatco for assistance.
Heating element and/or heated glass shelves not
working.
Base, glass shelf, and/or
canopy heat too hot.
Corresponding Heat Control Knob(s) set too high. Adjust the appropriate Heat Control Knob(s) to a lower
setting.
Heat Control(s) not working properly. Contact Authorized Service Agent or Hatco for assistance.
Supply voltage to unit is incorrect. Verify supply voltage at the receptacle matches the unit
specifications.
Display lights working, but
no heat.
Power On/Off switch(es) in “off” position. Move all Power On/Off switches to the “on” position.
GFCI(s) tripped. Reset GFCI. If GFCI continues to trip, contact Authorized
Service Agent or Hatco for assistance.
Heat Control(s) not working properly.
Contact Authorized Service Agent or Hatco for assistance.
Heating element and/or heated glass shelves not
working.
TROUBLESHOOTING GUIDE
Troubleshooting Questions?
If you continue to have problems resolving an issue, please contact the nearest Authorized Hatco Service Agency or Hatco for
assistance. To locate the nearest Service Agency, log onto the Hatco website at www.hatcocorp.com, select the Support pull-
down menu, and click on “Find A Service Agent”; or contact the Hatco Parts and Service Team at:
Telephone: 800-558-0607 or 414-671-6350
e-mail: [email protected]
WARNING
This unit must be serviced by qualified personnel only.
Service by unqualified personnel may lead to electric
shock or burn.
WARNING
ELECTRIC SHOCK HAZARD: Turn OFF power switch,
unplug power cord, and allow unit to cool before
performing any cleaning, setup, or maintenance.
Form No. GR3SDM-0920
14
English
OPTIONS AND ACCESSORIES
Sneeze Guards
Sneeze guards are available for all models as an added option
at the time of order. Sneeze guards can be installed above
each shelf on the customer side of the unit.
1. Remove protective paper from acrylic surfaces.
2. Secure mounting bracket into position with studs facing to
the front and downward by loosening three screws from
underside of shelf, inserting bracket at slots, and tighten
screws.
3. Position the acrylic sneeze guard onto the warmer with the
mounting holes aligned.
4. Secure the sneeze guard using the acorn nuts provided.
Tighten until snug. Do not over-tighten.
Stud
Acorn
Nut
Screw
Mounting
Bracket
Sneeze Guard Installation
Shelf Sign Holder
A shelf sign holder (sign not included) is available for the top
or middle shelf on the customer side. The shelf sign holder is
available as a factory-installed option only.
4″ (102 mm) Adjustable Legs
legs for installations that require additional clearance between
the unit and countertop.
Product Divider Rods
Stainless steel product divider rods are available as an
accessory.
3SD-DIV ................ Stainless Steel Divider Rod
Designer Colors
Designer colors are available as an option at the time of order.
Plexiglass Side Panels
Plexiglass side panels are available as a factory installed
option in lieu of glass side panels.
Flip-Up Doors
Flip-up doors are available for all models as an added option at
the time of order. Flip-up doors can be ordered on each shelf
and on either the customer side or operator side of the unit.
NOTE: Door should swing fully up for product placement.
NOTE: When loading/unloading product, use door hook to hold
flip-up door in the open position.
Form No. GR3SDM-0920 15
English
12″ (305 mm) Top Shelf Sign Holder
available for the top shelf only. The top shelf sign holder is
height of the unit.
Use the following procedure to install the top shelf sign holder.
WARNING
ELECTRIC SHOCK HAZARD:
• Turn power switch OFF, unplug power cord, and allow
unit to cool before performing any maintenance or
cleaning.
• This unit must be serviced by qualified personnel only.
Service by unqualified personnel may lead to shock or
burn.
1. Turn off and unplug the unit. Allow the unit to cool
completely.
2. Remove the channel divider rods and channel divider on
the control side of the unit.
3. Remove the channel divider brackets on the control side by
removing the nuts attaching them to the unit.
4. Align the holes on the sign holder brackets with the holes
previously used to secure the channel divider brackets.
NOTE: Make sure the sign holder is facing away from the control
side of the unit when installing the sign holder.
5. Secure the sign holder to the unit.
a. Place the channel divider bracket studs through the sign
holder bracket holes.
b. Tighten the nuts under the top of the unit.
6. Place the channel divider between the two channel divider
brackets.
7. Install the product divider rods into the channel dividers,
if desired. The rods can be adjusted easily to separate
holding areas as needed.
Nut
Sign Holde
r
Bracket
Sign Holder
(rear)
Channel
Divider
Bracket
Channel
Divider
GR3SDS Model Shown
OPTIONS AND ACCESSORIES
12” (305 mm) Top Shelf Sign Holder Installation
Form No. GR3SDM-0920
16
English
LIMITED WARRANTY
1. PRODUCT WARRANTY
Hatco warrants the products that it manufactures (the
“Products”) to be free from defects in materials and
workmanship, under normal use and service, for a period of
one (1) year from the date of purchase when installed and
maintained in accordance with Hatco’s written instructions
or 18 months from the date of shipment from Hatco. Buyer
must establish the Product’s purchase date by registering the
Product with Hatco or by other means satisfactory to Hatco in
its sole discretion.
Hatco warrants the following Product components to be free
from defects in materials and workmanship from the date of
purchase (subject to the foregoing conditions) for the period(s)
of time and on the conditions listed below:
a) One (1) Year Parts and Labor PLUS One (1) Additional
Year Parts-Only Warranty:
Conveyor Toaster Elements (metal sheathed)
Drawer Warmer Elements (metal sheathed)
Drawer Warmer Drawer Rollers and Slides
Strip Heater Elements (metal sheathed)
Display Warmer Elements (metal sheathed air heating)
Holding Cabinet Elements (metal sheathed air heating)
Heated Well Elements — HW and HWB Series
(metal sheathed)
b) Two (2) Year Parts and Labor Warranty:
Induction Ranges
Induction Warmers
c) One (1) Year Parts and Labor PLUS Four (4) Years
Parts-Only Warranty:
3CS and FR Tanks
d) One (1) Year Parts and Labor PLUS Nine (9) Years
Parts-Only Warranty on:
Electric Booster Heater Tanks
Gas Booster Heater Tanks
e) Ninety (90) Day Parts-Only Warranty:
Replacement Parts
THE FOREGOING WARRANTIES ARE EXCLUSIVE AND
IN LIEU OF ANY OTHER WARRANTY, EXPRESSED OR
IMPLIED, INCLUDING BUT NOT LIMITED TO ANY IMPLIED
WARRANTY OF MERCHANTABILITY OR FITNESS FOR
A PARTICULAR PURPOSE OR PATENT OR OTHER
INTELLECTUAL PROPERTY RIGHT INFRINGEMENT. Without
limiting the generality of the foregoing, SUCH WARRANTIES
DO NOT COVER: Coated incandescent light bulbs, fluorescent
lights, heat lamp bulbs, coated halogen light bulbs, halogen
heat lamp bulbs, xenon light bulbs, LED light tubes, glass
components, and fuses; Product failure in booster tank, fin
tube heat exchanger, or other water heating equipment caused
by liming, sediment buildup, chemical attack, or freezing;
or Product misuse, tampering or misapplication, improper
installation, or application of improper voltage.
2. LIMITATION OF REMEDIES AND DAMAGES
Hatco’s liability and Buyer’s exclusive remedy hereunder will
be limited solely, at Hatco’s option, to repair or replacement
using new or refurbished parts or Product by Hatco or a Hatco-
authorized service agency (other than where Buyer is located
outside of the United States, Canada, United Kingdom, or
Australia, in which case Hatco’s liability and Buyer’s exclusive
remedy hereunder will be limited solely to replacement of part
under warranty) with respect to any claim made within the
applicable warranty period referred to above. Hatco reserves
the right to accept or reject any such claim in whole or in part. In
the context of this Limited Warranty, “refurbished” means a part
or Product that has been returned to its original specifications
by Hatco or a Hatco-authorized service agency. Hatco will not
accept the return of any Product without prior written approval
from Hatco, and all such approved returns shall be made
at Buyer’s sole expense. HATCO WILL NOT BE LIABLE,
UNDER ANY CIRCUMSTANCES, FOR CONSEQUENTIAL
OR INCIDENTAL DAMAGES, INCLUDING BUT NOT LIMITED
TO LABOR COSTS OR LOST PROFITS RESULTING FROM
THE USE OF OR INABILITY TO USE THE PRODUCTS OR
FROM THE PRODUCTS BEING INCORPORATED IN OR
BECOMING A COMPONENT OF ANY OTHER PRODUCT OR
GOODS.
Formulaire n° GR3SDM-0920 17
Français
Ce manuel contient des instructions relatives à l’installation, à
la sécurité et au fonctionnement des présentoirs chauffants.
Hatco vous recommande de lire l’ensemble des instructions
d’installation et d’utilisation et toutes les consignes de sécurité
dans ce manuel avant d’installer et d’utiliser l’appareil.
Les consignes de sécurité qui apparaissent dans ce manuel
sont identifiées par les mots indicateurs suivants :
AVERTISSEMENT
AVERTISSEMENT indique une situation dangereuse qui, si
elle n’est pas évitée, peut provoquer la mort ou des bles-
sures graves.
ATTENTION
ATTENTION indique une situation dangereuse qui, si elle
n’est pas évitée, peut provoquer des blessures légères ou
moyennes.
AVIS
AVIS est utilisé pour des questions sans rapport avec des
blessures corporelles.
INTRODUCTION
Les présentoirs chauffants Glo-Ray® de Hatco GR3DSH
(rayonnage horizontal) et GR3SDS (rayonnage incliné) sont
parfaits pour maintenir au chaud des aliments enveloppés ou
mis en boîte sur une ligne de buffet ou aux points de service
des clients. Le socle chauffant à revêtement dur et à contrôle
thermostatique et la plaque chauffante vitrée unique et brevetée
permettent de maintenir au chaud des aliments enveloppés ou
mis en boîte et de les garder à des températures de service
optimales tout en garantissant la qualité des produits.
Ces présentoirs possèdent une plaque chauffante
supplémentaire sur le dessus, idéale pour maintenir à court
terme des aliments pour lesquels la température de service
n’est pas importante. Les présentoirs chauffants Glo-Ray sont
garantis un an contre la casse et le brûlage des circuits. Ces
appareils disposent également de lampes LED et d’un jeu de
cordons et de prises d’alimentation.
Les présentoirs chauffants Glo-Ray de Hatco sont le résultat de
recherches approfondies et de nombreux essais pratiques. Les
matériaux utilisés ont été sélectionnés pour un maximum de
durabilité, une belle apparence et une performance optimale.
Chaque appareil est minutieusement inspecté et testé avant
expédition.
Informations Importantes pour le Propriétaire ................ 17
Introduction .........................................................................17
Consignes de Sécurité Importantes ................................. 18
Description du Modèle .......................................................19
Tous les Modèles ...............................................................19
GR3SDH Modèles ............................................................. 19
GR3SDS Modèles .............................................................19
Désignation du Modèle ...................................................... 19
Caractéristiques Techniques ............................................20
Configuration des Fiches ...................................................20
Tableau des valeurs nominales électriques ......................20
Dimensions ........................................................................ 22
Installation ...........................................................................24
Généralités ........................................................................24
Mode d’emploi ....................................................................25
Généralités ........................................................................25
Panneau de contrôle .........................................................25
Fonctionnement de l’appareil ............................................25
Maintenance ........................................................................26
Généralités ........................................................................26
Nettoyage quotidien ...........................................................26
Disjoncteurs-détecteurs de fuite à la terre ........................26
Retrait des portes relevables en option.............................27
Guide de Dépannage ..........................................................28
Options et accessoires ...................................................... 29
Garantie Limitée .................................................................31
Autorisés Distributeurs de Pièces ........Couverture Arrière
INFORMATIONS IMPORTANTES POUR LE PROPRIÉTAIRE
Notez le numéro de modèle, le numéro de série, la tension
et la date d’achat de l’appareil dans les espaces ci-dessous
(étiquette des caractéristiques techniques située à l’arrière de
l’appareil). Veuillez avoir cette information à portée de la main
si vous appelez Hatco pour assistance.
Modèle No. ______________________________________
Numéro de série __________________________________
Voltage _________________________________________
Date d’achat _____________________________________
Enregistrez votre appareil!
Remplissez la garantie en ligne pour éviter les retards
pour faire jouer la garantie. Accédez au site Web Hatco
www.hatcocorp.com, sélectionnez le menu déroulant
Support (Assistance), puis cliquez sur « Warranty » (Garantie).
Horaires
ouvrables : 7h00 à 17h00 du lundi au vendredi
Heure du Centre (CT)
(Horaires d’été—juin à septembre:
7h00 à 17h00 du lundi au jeudi
7h00 à 16h00 le vendredi)
Téléphone: 800-558-0607; 414-671-6350
Courriel: [email protected]
Service d'assistance et de pièces de
rechange disponible 7j/7, 24h/24 aux
États-Unis et au Canada en composant
le 800-558-0607.
Des renseignements supplémentaires sont disponibles sur
notre site Web à www.hatcocorp.com.
SOMMAIRE
Formulaire n° GR3SDM-0920
18
Français
AVERTISSEMENT
S’assurer que le produit alimentaire a été chauffé à une
température adaptée au maintien de sa salubrité avant
de le mettre dans l’appareil sous peine de risques graves
pour la santé. Cet appareil est destiné au maintien au
chaud de produits alimentaires préchauffés uniquement.
Ne placez aucun produit alimentaire directement sur
une surface à revêtement dur. Les produits alimentaires
doivent être emballés, placés dans une boîte ou dans un
bac alimentaire.
Cet appareil ne doit pas être utilisé par des enfants ou des
personnes avec des capacités physiques, sensorielles ou
mentales diminuées. Assurez-vous que les enfants sont
bien surveillés et tenez-les à l’écart de l’appareil.
Cet appareil ne contient aucune pièce réparable par
l’utilisateur. Si cet appareil doit être réparé, contacter un
réparateur Hatco agréé ou le Service après-vente Hatco au
800-558-0607 ou 414-671-6350.
ATTENTION
DANGER DE BRÛLURE : Certaines surfaces extérieures
de l’appareil deviennent chaudes. Toucher ces zones de
l’appareil avec précaution.
Placer l’appareil sur un plan de travail de hauteur correcte
à un endroit qui convient pour son utilisation. Le support
doit être de niveau pour éviter toute chute accidentelle du
grille-pain ou de son contenu et suffisamment solide pour
résister au poids de l’appareil et de son contenu.
La National Sanitation Foundation (NSF) exige que les
appareils mesurant plus de 914 mm (36″) de largeur et
pesant plus de 36 kg (80 lbs.) soient hermétiquement fixés
ou rehaussés sur la surface d’installation. Si l’unité ne
peut pas être fixée à l’endroit d’utilisation, des pieds de 64
mm (2-1/2″) sont fournis pour permettre le nettoyage du
dessous de l’unité.
Ne déplacez pas et ne bougez pas l’appareil pour le
nettoyer. L’appareil est volumineux et lourd.
AVIS
Ne posez pas l’appareil sur la face avant ou sur la face
arrière. L’appareil pourrait être endommagé.
Utilisez uniquement des nettoyants non abrasifs et des
chiffons doux. Les chiffons et nettoyant abrasifs pourraient
rayer la finition de l’unité, altérant son apparence et la
rendant vulnérable à l’accumulation de saleté.
IMPORTANT—N’UTILISEZ JAMAIS une serviette en papier
ou un nettoyant pour vitres sur les surfaces en plastique
telles que les pare-haleine ou les capots rabattables. Les
serviettes en papier et le nettoyant pour vitres peuvent
rayer l’équipement. Essuyez les surfaces plastique à l’aide
d’un chiffon doux, propre et humide.
Empêchez toute surchauffe de la plaque vitrée. La
surchauffe peut faire fondre ou ramollir les contenants
alimentaires.
AVERTISSEMENT
DANGER DE DÉCHARGE ÉLECTRIQUE :
• Brancher l’appareil sur une prise de courant avec terre
de tension, de format et de configuration des broches
corrects. Si la fiche et la prise ne se correspondent pas,
s’adresser à un électricien qualifié pour déterminer et
installer une prise de courant de format et de tension
corrects.
• Éteignez l’appareil et débranchez le cordon
d’alimentation de la prise secteur et laissez refroidir
avant une maintenance ou un nettoyage.
• Si les appareils sont dotés de deux cordons
d’alimentation, ces derniers doivent tous deux être
débranchés avant d’effectuer tout nettoyage, réglage
ou entretien de l’appareil.
• NE PAS immerger l’appareil ni le saturer d’eau.
L’appareil n’est pas étanche à l’eau. Ne pas le faire
fonctionner s’il a été immergé ou saturé d’eau.
• L’appareil n’est pas à l’épreuve des intempéries. Placer
l’appareil à l’intérieur à une température ambiante de
21°C (70°F) minimum.
• Ne pas nettoyer à la vapeur ni utiliser trop d’eau sur
l’appareil.
• Cet appareil n’est pas étanche aux jets. Ne pas utiliser
de jet sous pression pour nettoyer l’appareil.
• Ne pas nettoyer l’appareil lorsqu’il est sous tension ou
chaud.
• Ne pas tirer l’appareil par son cordon électrique.
• Ne pas utiliser l’appareil si le cordon est endommagé
ou usé.
• Ne pas tenter de réparer ni de changer un cordon
électrique endommagé. Ce cordon doit être changé
par Hatco, par un réparateur Hatco agréé ou par une
personnes de qualifications comparables.
• Cet appareil doit uniquement être réparé par un personnel
qualifié. Toute réparation par un personnel non qualifié
peut entraîner une électrocution et des brûlures.
• Pour les réparations, utiliser exclusivement des
pièces de rechange Hatco d’origine. Utilisez des
pièces détachées Hatco authentiques sous peine
d’annuler toutes les garanties et d’exposer l’utilisateur
à des tensions électriques dangereuses pouvant
entraîner une électrocution ou des brûlures. Les
pièces de rechange Hatco d’origine sont conçues pour
fonctionner sans danger dans les environnements
dans lesquels elles sont utilisées. Certaines pièces
de rechange génériques ou de second marché ne
présentent pas les caractéristiques leur permettant de
fonctionner sans danger dans la matériel Hatco.
DANGER D’INCENDIE: Installez l’appareil de sorte à
conserver une distance minimale de 76 mm (3″) entre
l’arrière de l’appareil et le mur. Si une distance sûre n’est
pas maintenue, la chaleur peut provoquer une combustion
ou une altération de couleur.
Assurez-vous que tous les opérateurs ont été formés à
l’utilisation sûre et correcte de l’appareil.
CONSIGNES DE SÉCURITÉ IMPORTANTES
Lisez l’information de securite importante suivante avant d’utiliser cet équipement pour éviter
des dommages ou la mort sérieux et pour éviter d’endommager l’équipement ou la propriété.
Formulaire n° GR3SDM-0920 19
Français
DÉSIGNATION DU MODÈLE
Tous les Modèles
Tous les modèles GR3SD présentent un socle chauffant à
revêtement dur et à contrôle thermostatique ainsi qu’une double
source de chaleur vitrée qui conduit la chaleur vers le haut afin de
maintenir au chaud les aliments posés sur la plaque vitrée et qui
irradie vers le bas pour chauffer les produits situés en dessous.
Ces modèles comprennent également des panneaux latéraux
en verre trempé, des barres de division des produits, des lampes
LEDs et un jeu de cordons et de prises d’alimentation.
Modèles GR3SDH
Les modèles GR3SDH sont des présentoirs chauffants à
rayonnages horizontaux conçus pour maintenir au chaud des
produits alimentaires enveloppés ou mis en boîte.
Ces modèles sont disponibles dans des longueurs de 692 mm
plaque chauffante vitrée simple ou double.
Disjoncteur-détecteur
de fuite à la terre
Socle
chauffant à
revêtement
dur
Panneau
de contrôle
Plaque
chauffante
vitrée
Interrupteur
Marche/Arrêt
d’alimentation
Panneau
latéral vitré
Modèles GR3SDH
Modèles GR3SDS
Les modèles GR3SDS sont des présentoirs chauffants à
rayonnages inclinés conçus pour maintenir au chaud des
produits alimentaires enveloppés ou mis en boîte. Les
rayonnages sont inclinés pour faciliter le libre-service.
Ces modèles sont disponibles dans des longueurs de 692 mm
plaque chauffante vitrée simple ou double.
Disjoncteur-détecteur
de fuite à la terre
Socle
chauffant à
revêtement
dur
Panneau
de contrôle
Plaque
chauffante
vitrée
Interrupteur
Marche/Arrêt
d’alimentation
Panneau
latéral vitré
Modèles GR3SDS
NOTA: Des pare-haleine et des capots rabattables sont
disponibles pour les comptoirs chauffants. Consultez
la section OPTIONS ET ACCESSOIRES de ce manuel
pour plus de détails.
G R 3 S D H - x x D
Glo-Ray®
Vitrine pour sandwichs
Plaque chauffante vitrée
Largeur de l'appareil (en pouces)
Aucune lettre = Rayonnage simple
D = Rayonnage double
H = Rayonnage horizontal
S = Rayonnage incliné
CONSIGNES DE SÉCURITÉ IMPORTANTES
DESCRIPTION DU MODÈLE
AVIS
N’utilisez pas de bacs alimentaires, de plats en céramique
ou de matériaux abrasifs sur la plaque chauffante vitrée.
Cela pourrait rayer la surface vitrée, la détériorer et la
rendre plus salissante. Les dommages occasionnés à la
surface vitrée ou le bris de la vitre dus à une utilisation
inappropriée ne sont pas couverts par la garantie.
Ne pas placer l’appareil dans un endroit où la circulation de
l’air est trop forte. Évitez les zones pouvant être soumises
à des mouvements ou des courants d’air actifs (c.-à-d.
à proximité des ventilateurs/capots d’échappement, des
conduites de climatisation et des portes extérieures).
AVIS
Ne faites pas glisser de casseroles sur les surfaces
à revêtement dur, n’utilisez pas de casseroles avec
revêtement à fond dur et ne laissez rien tomber sur
les surfaces à couche dure. Cela pourrait rayer votre
équipement. Les dommages causés sur les surfaces à
revêtement dur dus à une mauvaise utilisation ne sont pas
couverts par la garantie.
Nettoyer chaque jour l’appareil pour éviter les
dysfonctionnements et maintenir l’hygiène.
Formulaire n° GR3SDM-0920
20
Français
Modèle Tension Intensité Amps
Configuration de
Fiches
Poids
d’embarquement
GR3SDH-27 120 997 8.3 NEMA 5-15P 50 kg. (108 lbs.)
GR3SDH-33 120 1251 10.4 NEMA 5-15P 55 kg. (120 lbs.)
GR3SDH-39 120 1505 12.5 NEMA 5-15P †60 kg. (133 lbs.)
CARACTÉRISTIQUES TECHNIQUES
Tableau des valeurs nominales électriques —
Modèles GR3SDH-xx (Rayonnage simple horizontal)
Tableau des valeurs nominales électriques —
Modèles GR3SDH-xxD (Rayonnage double horizontal)
Configuration des fiches
Les appareils sont équipés d’un câble d’alimentation électrique
adapté à la capacité nominale de l’appareil et doivent être
branchés à un circuit dédié à cet effet.
AVERTISSEMENT
DANGER DE DÉCHARGE ÉLECTRIQUE: Brancher
l’appareil sur une prise de courant avec terre de tension,
de format et de configuration des broches corrects. Si la
fiche et la prise ne se correspondent pas, s’adresser à un
électricien qualifié pour déterminer et installer une prise
de courant de format et de tension corrects.
NOTA: L’étiquette des caractéristiques techniques est
située à l’arrière de l’appareil. Consultez l’étiquette
pour connaître le numéro de série et vérifier les
caractéristiques électriques de l’appareil.
NEMA 5-15P NEMA 5-20P
NEMA L14-20P NEMA 14-20P
Configuration des fiches
NOTA: Prise non fournie par Hatco.
† NEMA 5-20P pour le Canada.
• NEMA 14-20P en option.
Modèle Tension Intensité Amps
Configuration de
Fiches
Poids
d’embarquement
GR3SDH-27D 120 1769 14.7 NEMA 5-15P †67 kg. (147 lbs.)
GR3SDH-33D 120/208240 2227 10.3 NEMA L14-20P •75 kg. (166 lbs.)
GR3SDH-39D 120/208240 2685 12.3 NEMA L14-20P •88 kg. (194 lbs.)
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
dans d''autres langues
- English: Hatco GR3SDH User manual
Documents connexes
-
Hatco GR3SDH, GR3SDH-xxD, GR3SDS, GR3SDS-xxD Series Le manuel du propriétaire
-
Hatco GR2SD Series Manuel utilisateur
-
Hatco Glo-Ray GR2SDH-36 Le manuel du propriétaire
-
-
-
-
-
-
-
