Hatco GRHW Series Le manuel du propriétaire

Hatco
Marque
Hatco
Modèle
GRHW Series
Taper
Le manuel du propriétaire
hatcocorp.com
Register Online!
(see page 2)
S’inscrire en ligne!
(voir page 15)
Do not operate this equipment unless you
have read and understood the contents
of this manual! Failure to follow the
instructions contained in this manual
may result in serious injury or death.
This manual contains important safety
information concerning the maintenance,
use, and operation of this product. If
you’re unable to understand the contents
of this manual, please bring it to the
attention of your supervisor. Keep this
manual in a safe location for future
reference.
English = p 2
WARNING
No opere este equipo al menos que haya
leído y comprendido el contenido de este
manual! Cualquier falla en el seguimiento
de las instrucciones contenidas en
este manual puede resultar en un serio
lesión o muerte. Este manual contiene
importante información sobre seguridad
concerniente al mantenimiento, uso y
operación de este producto. Si usted
no puede entender el contenido de
este manual por favor pregunte a su
supervisor. Almacenar este manual en
una localización segura para la referencia
futura.
ADVERTENCIA
Ne pas utiliser cet équipement sans avoir
lu et compris le contenu de ce manuel ! Le
non-respect des instructions contenues
dans ce manuel peut entraîner de
graves blessures ou la mort. Ce manuel
contient des informations importantes
concernant l’entretien, l’utilisation et le
fonctionnement de ce produit. Si vous ne
comprenez pas le contenu de ce manuel,
veuillez le signaler à votre supérieur.
Conservez ce manuel dans un endroit
sûr pour pouvoir vous y référer plus tard.
Français = p 15
AVERTISSEMENT
Glo-Ray
®
Mini-Merchandisers
Mini-Présentoirs
GRHW Series/Série
Installation and Operating Manual
Manuel d’installation et d’utilisation
P/N 07.04.357.00 © 2020 Hatco Corporation
2
Form No. GRHWM-0520
English
CONTENTS
Hatco Glo-Ray
®
GRHW Series Mini-Merchandisers keep
wrapped or packaged foods hot at kitchen work areas,
waitress pick-up stations, or customer serving points. These
merchandisers feature a thermostatically-controlled heated
base along with prefocused infrared overhead heat to extend
the holding times of most food.
The infrared heating elements are guaranteed against breakage
and burnout for two years and the base heating elements are
guaranteed against burnout for one year.
Hatco Glo-Ray Mini-Merchandisers are products of extensive
research and field testing. The materials used were selected
for maximum durability, attractive appearance, and optimum
performance. Every unit is inspected and tested thoroughly
prior to shipment.
This manual provides the installation, safety, and operating
instructions for Hatco Glo-Ray Mini-Merchandisers. Hatco
recommends all installation, operating, and safety instructions
appearing in this manual be read prior to installation or
operation of a unit.
Safety information that appears in this manual is identified by
the following signal word panels:
WARNING
WARNING indicates a hazardous situation which, if not
avoided, could result in death or serious injury.
CAUTION
CAUTION indicates a hazardous situation which, if not
avoided, could result in minor or moderate injury.
NOTICE
NOTICE is used to address practices not related to
personal injury.
Important Owner Information ..............................................2
Introduction ...........................................................................2
Important Safety Information ..............................................3
Model Description ................................................................4
All Models ............................................................................ 4
Model Designation ...............................................................5
Specifications .......................................................................5
Plug Configurations .............................................................5
Electrical Rating Chart .........................................................5
Dimensions .......................................................................... 6
Installation .............................................................................7
General ................................................................................ 7
Installing the Sneeze Guard ................................................ 7
Installing the Side Panels .................................................... 8
Operation ...............................................................................9
General ................................................................................ 9
Maintenance ........................................................................10
General .............................................................................. 10
Daily Cleaning ...................................................................10
Replacing Display Lights ...................................................10
Ground Fault Circuit Interrupter (GFCI) ............................10
Troubleshooting Guide ...................................................... 11
Options and Accessories ..................................................12
Limited Warranty ................................................................14
Authorized Parts Distributors ...........................Back Cover
IMPORTANT OWNER INFORMATION
Record the model number, serial number (specification label
located on the top rear of the unit), voltage, and purchase date
of the unit in the spaces below. Please have this information
available when calling Hatco for service assistance.
Model No. ____________________________________
Serial No. _____________________________________
Voltage _______________________________________
Date of Purchase _______________________________
Register your unit!
Completing online warranty registration will prevent delay in
obtaining warranty coverage. Access the Hatco website at
www.hatcocorp.com, select the Support pull-down menu,
and click on “Warranty”.
Business
Hours: 7:00  to 5:00  Monday–Friday,
Central Time (CT)
(Summer Hours: June to September—
7:00  to 5:00  Monday–Thursday
7:00  to 4:00  Friday)
Telephone: 800-558-0607; 414-671-6350
E-mail: [email protected]
24 Hour 7 Day Parts and Service
Assistance available in the United States
and Canada by calling 800-558-0607.
Additional information can be found by visiting our web site at
www.hatcocorp.com.
INTRODUCTION
Form No. GRHWM-0520
3
English
IMPORTANT SAFETY INFORMATION
WARNING
ELECTRIC SHOCK HAZARD:
• Plug unit into a properly grounded electrical receptacle
of the correct voltage, size, and plug configuration. If
plug and receptacle do not match, contact a qualified
electrician to determine and install the proper voltage
and size electrical receptacle.
• Turn OFF power switch, unplug power cord, and allow
unit to cool before performing any maintenance or
cleaning.
• DO NOT submerge or saturate with water. Unit is not
waterproof. Do not operate if unit has been submerged
or saturated with water.
• Unit is not weatherproof. Locate unit indoors where
ambient air temperature is a minimum of 70°F (21°C).
• Do not steam clean or use excessive water on unit.
• Do not pull unit by power cord.
• Discontinue use if power cord is frayed or worn.
• Do not attempt to repair or replace a damaged
power cord. The cord must be replaced by Hatco, an
Authorized Hatco Service Agent, or a person with
similar qualifications.
• This unit must be serviced by qualified personnel only.
Service by unqualified personnel may lead to electric
shock or burn.
• Use only Genuine Hatco Replacement Parts when
service is required. Failure to use Genuine Hatco
Replacement Parts will void all warranties and may
subject operators of the equipment to hazardous
electrical voltage, resulting in electrical shock or burn.
Genuine Hatco Replacement Parts are specified to
operate safely in the environments in which they are
used. Some aftermarket or generic replacement parts
do not have the characteristics that will allow them to
operate safely in Hatco equipment.
FIRE HAZARD: Locate unit a minimum of 1″ (25 mm) from
combustible walls and materials. If safe distances are not
maintained, discoloration or combustion could occur.
EXPLOSION HAZARD: Do not store or use gasoline or
other flammable vapors or liquids in the vicinity of this or
any other appliance.
Make sure food product has been heated to the proper
food-safe temperature before placing on the unit. Failure
to heat food product properly may result in serious health
risks. This unit is for holding preheated food product only.
This unit is not intended for use by children or persons
with reduced physical, sensory, or mental capabilities.
Ensure proper supervision of children and keep them
away from the unit.
Make sure all operators have been instructed on the safe
and proper use of the unit.
WARNING
Use only light bulbs that meet or exceed National
Sanitation Foundation (NSF) standards and are specifically
designed for food holding areas. Breakage of light bulbs
not specially coated could result in personal injury and/or
food contamination.
This unit has no “user-serviceable” parts. If service
is required on this unit, contact an Authorized Hatco
Service Agent or contact the Hatco Service Department at
800-558-0607 or 414-671-6350.
CAUTION
BURN HAZARD: Some exterior surfaces on unit will get
hot. Use caution when touching these areas.
Locate unit at proper counter height in an area that is
convenient for use. The location should be level to prevent
unit or its contents from falling accidentally and strong
enough to support the weight of unit and contents.
The National Sanitation Foundation (NSF) requires that
units over 36″ (914 mm) in width or weighing more than
80 lbs. (36 kg) either be sealed to or raised above the
installation surface. If unit cannot be sealed at the point
of use, 4″ (102 mm) legs are included to allow for proper
cleaning access below unit.
NOTICE
Do not allow the glass shelf to overheat. Overheating may
cause the food containers to melt or soften.
Do not use food pans, ceramic dishes, or abrasive
materials on heated glass shelf. Scratching of the glass
surface may occur, marring its appearance and making it
susceptible to dirt accumulation. Damage to glass surface
or breakage of glass caused by misuse is not covered
under warranty.
Do not slide pans across hardcoat surface, use rough-
bottomed pans, or drop anything on hardcoat surface.
Scratching may occur. Damage to hardcoat surface caused
by misuse is not covered under warranty.
Do not lay unit on the side with the control panel. Damage
to unit could occur.
Use non-abrasive cleaners only. Abrasive cleaners could
scratch the finish of the unit, marring its appearance and
making it susceptible to soil accumulation.
IMPORTANT—DO NOT use paper towel or glass cleaner
to clean polycarbonate surfaces. Paper towel and glass
cleaner may scratch the material. Wipe off polycarbonate
surfaces using a soft, clean, and damp cloth.
Do not drag or slide unit when moving or installing.
Carefully lift unit to prevent the rubber feet from tearing
off.
Locate the unit in an area where the ambient air temperature
is constant and a minimum of 70°F (21°C). Avoid areas that
may be subject to active air movements or currents (i.e.,
near exhaust fans/hoods and air conditioning ducts).
Read the following important safety information before using this equipment to avoid serious
injury or death and to avoid damage to equipment or property.
4
Form No. GRHWM-0520
English
GRHW-1SGD and GRHW-1SGDS Models
The GRHW-1SGD and GRHW-1SDS models feature a
stainless steel or hardcoated heated base and an upper heated
glass shelf with glass side panels.
The GRHW-1SGD model has a horizontal, stainless steel
heated base and a horizontal heated glass shelf. It is available
with an optional hardcoated heated base.
The GRHW-1SGDS model has a slanted, hardcoated heated
base and a slanted heated glass shelf.
Controls for both models include a lighted Power ON/OFF (I/O)
switch, a base heat control, and a glass shelf heat control.
An optional digital temperature controller is available (see
OPTIONS AND ACCESSORIES section for details).
Heated Glass
Shelf
Glass Side
Panel
Heated Base
Personnel
Protector
Sneeze
Guard
Model GRHW-1SGDS
MODEL DESCRIPTION
All Models
GRHW Series Mini-Merchandisers use a limited amount of
counterspace and come in a variety of shapes, sizes, and colors
to hold food samples, hors d’oeuvres, and packaged product.
All GRHW models feature a thermostatically-controlled heated
base, a sneeze guard, overhead infrared heating elements,
overhead display lights, optional Designer    
(1829 mm) cord and plug set.
NOTE: Refer to the OPTIONS AND ACCESSORIES section
for additional information.
GRHW-1P and GRHW-2P Models
The GRHW-1P and GRHW-2P models are Hors D’oeuvre
Warmers. The GRHW-1P has a one-pan capacity with


Controls for both models include a lighted Power ON/OFF
(I/O) rocker switch, a base heat control, a Power ON/OFF (I/O)
toggle switch, and an optional overhead heat control.
Heated
Base
Shelf
Sneeze
Guard
Model GRHW-1P
GRHW-1SG and GRHW-1SGS Models
The GRHW-1SG and GRHW-1SGS models feature personnel

horizontal heated base and the GRHW-1SGS has a slanted
heated base and polycarbonate side panels.
   
available for the GRHW-1SG model as accessories.
Controls for both models include a lighted Power ON/OFF
(I/O) rocker switch, a base heat control, a Power ON/OFF (I/O)
toggle switch, and an optional overhead heat control.
Sneeze
Guard
Heated Base
Shelf
Personnel
Protector
4” Bins
Model GRHW-1SG
Form No. GRHWM-0520
5
English
MODEL DESIGNATION
G R H W - x P
Glo-Ray
P = Pans
SG = Single Horizontal Shelf
SGS = Single Slanted Shelf
SGD = Dual Horizontal Shelf with
Heated Glass Upper Shelf
SGDS = Dual Slanted Shelf with
Heated Glass Upper Shelf
Hors D’ouevres Warmer/
Mini-Merchandiser
Quantity of Pans
SPECIFICATIONS
Plug Configurations
Units are supplied from the factory with an electrical cord and
plug installed. Plugs are supplied according to the applications.
WARNING
ELECTRIC SHOCK HAZARD: Plug unit into a properly
grounded electrical receptacle of the correct voltage,
size, and plug configuration. If plug and receptacle do not
match, contact a qualified electrician to determine and
install the proper voltage and size electrical receptacle.
NOTE: The specification label is located on the top rear of the
unit. See label for serial number and verification of unit
electrical information.
NEMA 5-15P
CEE 7/7 Schuko AS-3112
BS-1363
NEMA 5-20P
Plug Configurations
NOTE: Receptacle not supplied by Hatco.
Electrical Rating Chart
* NEMA 5-20P for Canada
The shaded areas contain electrical information for International models only.
NOTE: Shipping weights are estimated.
Model Voltage Watts Amps Plug Configuration Shipping Weight
GRHW-1P 120 820 6.8 NEMA 5-15P
35 lbs. (16 kg)
220 782 3.6 CEE 7/7 Schuko or BS-1363
240 838 3.5 CEE 7/7 Schuko or AS 3112
220–230 782–855 3.6–3.7 CEE 7/7 Schuko
230–240 770–838 3.3–3.5 BS-1363
GRHW-2P 120 1640 13.7 NEMA 5-15P *
67 lbs. (31 kg)
220 1560 7.1 CEE 7/7 Schuko or BS-1363
240 1680 7.0 CEE 7/7 Schuko or AS 3112
220–230 1560–1705 7.1–7.4 CEE 7/7 Schuko
230–240 1543–1680 6.7–7.0 BS-1363
GRHW-1SG 120 820 6.8 NEMA 5-15P
37 lbs. (17 kg)220 782 3.6 CEE 7/7 Schuko
240 838 3.5 BS-1363
GRHW-1SGS 120 820 6.8 NEMA 5-15P
40 lbs. (18 kg)220
820
3.7 CEE 7/7 Schuko
240 3.4 BS-1363
GRHW-1SGD 120 1330 11.1 NEMA 5-15P 73 lbs. (33 kg)
GRHW-1SGDS 120 1330 11.1 NEMA 5-15P 73 lbs. (33 kg)
6
Form No. GRHWM-0520
English
Model
Width
(A)
Depth
(B)
Height
(C)
Footprint
Width (D)
Footprint
Depth (E)
GRHW-1P 22-1/4
(565 mm)
19-1/8
(486 mm)
17-3/4
†
(451 mm)
19-7/8
(505 mm)
11-3/8
(289 mm)
GRHW-2P 43-1/4
(1099 mm)
19-1/8
(486 mm)
20-3/4
(527 mm)
40-7/8
(1038 mm)
11-3/8
(289 mm)
GRHW-1SG 22-1/4
(565 mm)
19-1/8
(486 mm)
17-3/4
†
(451mm)
19-7/8
(505 mm)
11-3/8
(289 mm)
GRHW-1SGS 22-1/4
(565 mm)
19-1/8
(486 mm)
18-1/4
(464 mm)
19-7/8
(505 mm)
11-3/8
(289 mm)
GRHW-1SGD 22-7/8
(581 mm)
20-1/2
(521 mm)
23-1/2
(597 mm)
19-7/8
(505 mm)
11-3/8
(289 mm)
GRHW-1SGDS 22-3/4
(578 mm)
21
(534 mm)
23-5/8
(600 mm)
19-7/8
(505 mm)
11-3/8
(289 mm)
SPECIFICATIONS
Dimensions
$
&
(
%
'
6LGH9LHZ)URQW9LHZ
GRHW-1P, -2P, -1SG, and -1SGS Dimensions
†

Side ViewFront View
A
C
E
B
D
GRHW-1SGD and GRHW-1SGDS Dimensions
Form No. GRHWM-0520
7
English
6. Place the unit in the desired location. Two people are
required for this step.
• Locate the unit in an area where the ambient air
temperature is constant and a minimum of 70°F (21°C).

or currents (i.e., near exhaust fans/hoods and air
conditioning ducts).
• Make sure the unit is at the proper counter height in an
area convenient for use.
• Make sure the countertop is level and strong enough to
support the weight of the unit and food product.
Installing the Sneeze Guard
All models are shipped with sneeze guards. Use the appropriate
procedure to install a sneeze guard on a unit.
NOTE: Make sure to install the sneeze guard before installing
side panels, if equipped.
GRHW-1P, -2P, -1SG, and -1SGS Models
1. Assemble each weld screw through the top of the sneeze
guard and through the support trim. Loosely thread a cap
nut onto each of the weld screws below the support trim.
2. Lift the sneeze guard assembly and carefully slide each of
the weld screws that are loosely attached to the sneeze
guard into the channel on the unit.
3. Align each end of the sneeze guard with the ends of the
unit and then tighten the cap nuts to secure the sneeze
guard in position. Do not over-tighten the cap nuts.
Cap Nut
Support
Trim
Sneeze
Guard
Channel
Weld
Screw
Installing a Sneeze Guard
(GRHW-1SG model shown)
continued...
INSTALLATION
General
Glo-Ray
®
GRHW Series Mini-Merchandisers are shipped
with most components pre-assembled. Care should be taken
when unpacking shipping carton to avoid damage to unit and
components enclosed.
WARNING
ELECTRIC SHOCK HAZARD: Unit is not weatherproof.
Locate unit indoors where the ambient air temperature is a
minimum of 70°F (21°C).
FIRE HAZARD: Locate unit a minimum of 1″ (25 mm) from
combustible walls and materials. If safe distances are not
maintained, discoloration or combustion could occur.
CAUTION
Locate unit at the proper counter height in an area that is
convenient for use. The location should be level to prevent
the unit or its contents from falling accidentally and strong
enough to support the weight of the unit and contents.
The National Sanitation Foundation (NSF) requires that
units over 36″ (914 mm) in width or weighing more than
80 lbs. (36 kg) either be sealed to or raised above the
installation surface. If unit cannot be sealed at the point
of use, 4″ (102 mm) legs are included to allow for proper
cleaning access below unit.
NOTICE
Do not drag or slide unit when moving or installing.
Carefully lift unit to prevent the rubber feet from tearing off.
1. Remove the unit from the box.
NOTE: To prevent delay in obtaining warranty coverage,
complete online warranty registration. See the
IMPORTANT OWNER INFORMATION section for
details.
2. Remove tape and protective packaging from all surfaces
of unit.
3. Install the sneeze guard. Refer to the “Installing the Sneeze
Guard” procedure in this section.
4. Install the side panels, if equipped. Refer to the “Installing
the Side Panels” procedure in this section.
5. Tighten thumbscrews holding the front and rear personnel
protectors in place until snug, if equipped.
Thumbscrew
Personnel
Protector
Personnel Protector Installation
(GRHW-1SG model shown)
8
Form No. GRHWM-0520
English
INSTALLATION
GRHW-1SGD and GRHW-1SGDS Models
1. Align the four holes in the sneeze guard and support trim
with the four studs located underneath the front top of the
unit.
2. Secure the sneeze guard and support trim to the studs with
the four supplied cap nuts. Do not over-tighten the cap nuts.
Sneeze Guard
Stud
Support Trim
Cap Nut
Installing a Sneeze Guard
(GRHW-1SGDS model shown)
Installing the Side Panels
Some models are shipped with side panels. Use the appropriate
procedure to install side panels on a unit.
GRHW-1P, -2P, -1SG, and -1SGS Models
The above models can be equipped with polycarbonate side
panels. To install a polycarbonate side panel:
NOTE: Make sure to install the sneeze guard before installing
side panels, if equipped.
1. Align the four holes in the side panel with the corresponding
holes in the two support posts.
• Make sure the slanted edge of the side panel is aligned
with the sneeze guard.
2. Secure the side panel to the support posts using the four
supplied screws. Do not over-tighten the screws.
Screw
Polycarbonate
Side Panel
Support
Post
Polycarbonate Side Panel Installation
(GRHW-1SG model shown)
GRHW-1SGD and GRHW-1SGDS Models
All GRHW-1SGD and GRHW-1SGDS models are equipped
with glass side panels. To install a glass side panel:
1. Remove the two screws from the Z bracket and remove
bracket.
2. Place glass side panel into the bottom brackets.
3. Re-install the Z bracket with the two screws previously
removed.
Glass
Side
Panel
“OUT”
Facing
Outward
Screws
Z Bracket
Glass Side Panel Installation
(GRHW-1SGDS model shown)
NOTE: Side glass panels have a special “Low E” coating
applied to one side to help reduce heat loss through
the glass. The “Low E” coated side must face inward
and the word “OUT” on the glass must face outward.
Form No. GRHWM-0520
9
English
OPERATION
GRHW-1SGD and GRHW-1SGDS
1. Move the Power I/O (on/off) switch to the I (on) position.
• The overhead lights will turn on, the overhead heating
element will turn on, the heated glass shelf will energize,
and the base heating element will energize.
2. Turn the base heat control to the desired temperature
setting.
3. Turn the glass shelf heat control to the desired setting.
Glass Shelf
Heat Control
Ground Fault
Circuit Interrupter
(GFCI)
Base Heat
Control
Power I/O
(on/off) Switch
Controls for GRHW-1SGD and GRHW-1SGDS
(GRHW-1SDS controls shown)
Shutdown
GRHW-1P, -2P, -1SG, and -1SGS
1. Move the Power I/O (on/off) switch on the base to the O
(off) position. The overhead lights and heated base will
shut off.
2. If the unit is equipped with a Power I/O (on/off) toggle
switch or an overhead heat control in the upper housing,
move the switch to the O (off) position or turn the control
to the OFF (O) position. The overhead heating element will
shut off.
3. If the unit is equipped with both a Power I/O (on/off) toggle
switch and an overhead heat control in the upper housing:
• Move the Power I/O toggle switch to the O (off) position.
The overhead lights will turn on.
• Turn the overhead heat control to the OFF (O) position.
The overhead heating element will shut off.
GRHW-1SGD and GRHW-1SGDS
1. Move the Power I/O (on/off) switch to the O (off) position.
The overhead lights, overhead heating element, heated
glass shelf, and heated base will shut off.
NOTE: Refer to the MAINTENANCE section for Ground Fault
Circuit Interrupt (GFCI) switch information.
General
Use the following procedures to operate the Glo-Ray
®
GRHW
Series Mini-Merchandisers.
WARNING
Read all safety messages in the IMPORTANT SAFETY
INFORMATION section before operating this equipment.
Startup
Perform the following step for startup of all GRHW models and
then proceed to the appropriate section for the remaining steps
for startup.
1. Plug unit into a properly grounded electrical receptacle of
the correct voltage, size and plug configuration. See the
SPECIFICATIONS section for details.
GRHW-1P, -2P, -1SG, and -1SGS
1. Move the Power I/O (on/off) switch on the base to the I
(on) position. The base heat control will energize and the
overhead lights will turn on.
2. Turn the base heat control to the desired temperature
setting. The base temperature range is from 82°F to 200°F
(28°C to 93°C).
Power I/O
(on/off) Switch
Base Heat
Control
Base controls for GRHW-1P, -2P, -1SG, and -1SGS
3. If the unit is equipped with a Power I/O (on/off) toggle switch
or an overhead heat control in the upper housing, move the
switch to the I (on) position or turn the control to the desired
setting. The overhead heating element will energize.
4. If the unit is equipped with both a Power I/O (on/off)) toggle
switch and an overhead heat control in the upper housing:
• Move the Power I/O toggle switch to the I (on) position.
The overhead lights will turn on.
• Turn the overhead heat control to the desired setting.
The overhead heating element will energize.
Power I/O (on/off)
Toggle Switch
Overhead
Heat Control
(optional)
Top controls for GRHW-1P, -2P, -1SG, and -1SGS
10
Form No. GRHWM-0520
English
MAINTENANCE
General
GRHW Series Mini-Merchandisers are designed for maximum
durability and performance, with minimum maintenance.
WARNING
ELECTRIC SHOCK HAZARD:
• Turn power switch OFF, unplug power cord, and allow
unit to cool before performing any maintenance or
cleaning.
• DO NOT submerge or saturate with water. Unit is not
waterproof. Do not operate if unit has been submerged
or saturated with water.
• Do not steam clean or use excessive water on unit.
• Do not clean unit when it is energized or hot.
• Use only Genuine Hatco Replacement Parts when
service is required. Failure to use Genuine Hatco
Replacement Parts will void all warranties and may
subject operators of the equipment to hazardous
electrical voltage, resulting in electrical shock or burn.
Genuine Hatco Replacement Parts are specified to
operate safely in the environments in which they are
used. Some aftermarket or generic replacement parts
do not have the characteristics that will allow them to
operate safely in Hatco equipment.
This unit has no “user-serviceable” parts. If service
is required on this unit, contact an Authorized Hatco
Service Agent or contact the Hatco Service Department at
800-558-0607 or 414-671-6350.
Daily Cleaning
To preserve the finish of the unit as well as maintain
performance, it is recommended that the unit be cleaned daily.
NOTICE
Submerging or saturating unit with water will damage unit
and void product warranty.
Do not drag or slide unit when moving or installing.
Carefully lift unit to prevent the rubber feet from tearing off.
IMPORTANT — DO NOT use paper towel or glass cleaner
to clean polycarbonate surfaces. Paper towel and glass
cleaner may scratch the material. Wipe off polycarbonate
surfaces using a soft, clean, and damp cloth.
1. Turn off the unit, unplug the power cord, and allow the unit
to cool.
2. Wipe down all exterior and interior surfaces using a damp
cloth. A non-abrasive cleaner may be used for difficult
stains. Hard to reach areas should be cleaned using a
small brush and mild soap.
3. Clean the polycarbonate sneeze guard and side panels
using a mild, soapy water solution and a damp, soft cloth.
NOTICE: DO NOT use paper towel or glass cleaner.
4. Clean the glass side panels using a standard glass cleaner
(GRHW-1SGD and GRHW-1SGDS models only).
5. Clean the heated glass surface using a standard ceramic
glass stove top cleaner.
Replacing Display Lights
WARNING
Use only light bulbs that meet or exceed National
Sanitation Foundation (NSF) standards and are specifically
designed for food holding areas. Breakage of light bulbs
not specially coated could result in personal injury and/or
food contamination.
The display lights illuminate the warming area. Each bulb has a

in the event of breakage.
1. Turn off the unit, unplug the power cord, and allow the unit
to cool.
2. Unscrew the light bulb from the unit and replace it with a
new, specially-coated incandescent light bulb.
NOTE: Hatco shatter-resistant incandescent light bulbs meet
NSF standards for food holding and display areas. For
120 V applications, use Hatco P/N 02.30.265.00. For 220,
240, 220–230, and 230–240 V applications, use Hatco
P/N 02.30.266.00.
NOTE: Shatter-resistant halogen bulbs are available in place
of the standard incandescent bulbs. Halogen bulbs
have a special coating to guard against injury and food
contamination in the event of breakage. For 120 V
units, use Hatco P/N 02.30.081.00.
NOTE: Refer to the OPTIONS AND ACCESSORIES section for
Chef LED information.
Ground Fault Circuit Interrupter (GFCI)
The GRHW-1SGD and the GRHW-1SGDS are supplied with a
built-in Ground Fault Circuit Interrupter (GFCI) that is designed to
turn off electrical power and help prevent damage to the internal
components when there is a short circuit or electrical fault.
To reset the GFCI:
1. Make sure the unit is plugged in and all ON/OFF switches
are in the ON position.
2. Push the red RESET button.
If the GFCI continues to trip, contact your local Authorized
Hatco Service Agency.
RESET Button
Ground Fault Circuit
Interrupter (GFCI)
Ground Fault Circuit Interrupter
Form No. GRHWM-0520
11
English
Symptom Probable Cause Corrective Action
Overhead heat is too hot. Overhead heat control set too high.  heat control to a lower setting.
Overhead heat control defective. Contact Authorized Service Agent or Hatco for assistance.
Unit plugged into incorrect/high voltage. Verify that voltage supply matches electrical information
listed on the unit.
Overhead heat is not hot
enough.
Overhead heat control set too low.  heat control to a higher setting.
Overhead heat control defective.
Contact Authorized Service Agent or Hatco for assistance.
Heating elements not working.
Excessive air movement around unit. Relocate unit or redirect air movement (i.e. air conditioning
duct or exhaust fan) away from unit.
Base heat is too hot. Base heat control set too high.  heat control to a lower setting.
Base heat control defective. Contact Authorized Service Agent or Hatco for assistance.
Unit plugged into incorrect/high voltage. Verify that voltage supply matches electrical information
listed on the unit.
Base heat is not hot enough. Base heat control set too low.  heat control to a higher setting.
Base heat control defective.
Contact Authorized Service Agent or Hatco for assistance.
Base heating element not working.
Excessive air movement around warming
cabinet.
Relocate unit or redirect air movement (i.e. air conditioning
duct or exhaust fan) away from unit.
No heat. Heating elements not working.
Contact Authorized Service Agent or Hatco for assistance.
Base heat control and/or overhead heat control
not working properly.
Unit plugged into incorrect/low voltage. Verify that voltage supply matches electrical information
listed on the unit.
No heat and no lights. ON/OFF Switch turned OFF. Move ON/OFF Switch to ON position.
Unit not plugged in or outlet not working. Plug in unit, have outlet repaired by a certified electrician, or
use a different outlet.
Circuit breaker tripped. Reset circuit breaker. If circuit breaker continues to trip,
contact Authorized Service Agent or Hatco for assistance.
GFCI tripped. Reset GFCI. If GFCI continues to trip, contact Authorized
Service Agent or Hatco for assistance.
ON/OFF switch defective. Contact Authorized Service Agent or Hatco for assistance.
TROUBLESHOOTING GUIDE
WARNING
This unit must be serviced by trained and qualified
personnel only. Service by unqualified personnel may lead
to electric shock or burn.
WARNING
ELECTRIC SHOCK HAZARD: Turn OFF power switch,
unplug power cord, and allow unit to cool before
performing any maintenance or cleaning.
Troubleshooting Questions?
If you continue to have problems resolving an issue, please contact the nearest Authorized Hatco Service Agency or Hatco for
assistance. To locate the nearest Service Agency, log onto the Hatco website at www.hatcocorp.com, select the Support pull-
down menu, and click on “Find A Service Agent”; or contact the Hatco Parts and Service Team at:
Telephone: 800-558-0607 or 414-671-6350
e-mail: [email protected]
12
Form No. GRHWM-0520
English
OPTIONS AND ACCESSORIES
Display Sign Holder
A display sign holder is available as an accessory for
GRHW-1SG, -1SGS, -1SGD, and -1SGDS models. A display


sign (not included).
Installing the Sign Holder
Use the following procedure to install the sign holder to the unit.
1. Remove the two upper screws from each side of the unit.
2. Align the screw holes on the sign holder with the screw
holes on the side of the unit.
3. Install the sign holder to the unit using the original screws.
Screw
Sign Holder
(Accessory)
Installing Sign Holder (GRHW-1SG model shown)
Digital Temperature Controller
A digital temperature controller option is available for
GRHW-1SGD and GRHW-1SGDS models only. The digital
temperature controller replaces the standard base heat control
to monitor and control the temperature of the heated base.
Use the following procedures to operate a digital temperature
controller.
NOTE: This option is factory-installed only, not available for
retrofit.
NOTE: Units manufactured for use outside the United States
and Canada will have digital temperature controllers
that indicate temperature in Celsius (°C).
Down Arrow
Key
Up Arrow
Key
“out 1”
Fahrenheit
Symbol
SET
Key
Digital Temperature Controller
1. Move the unit Power On/Off switch to the “On” position.
• The overhead lights will turn on, the overhead heating
element will turn on, the heated glass shelf will energize,
and the base heating element will energize. CAUTION!
Some exterior surfaces on the unit will get hot. Use
caution when touching these areas.
• The digital temperature controller will energize and the
current temperature of the heated base will appear on
the display.
• The phrase “out 1” will appear in the upper left corner of
the display to show that the base is in heat mode.
2. Press and release the key. The current setpoint
temperature will be shown on the display and ”out 1” will
flash in the upper left corner.
3. Press the key or key within 15 seconds to
change the setpoint temperature. If no key is pressed
within 15 seconds, the display will revert to the current
temperature of the heated base.
4. Press the key or wait 15 seconds to lock in the new
setpoint temperature. The setpoint temperature range of
the controller is from room temperature to the maximum
operating temperature of the unit.
Locking/Unlocking the Digital Temperature
Controller
The keys on the digital temperature controller can be locked to
prevent unauthorized changes to the settings.
To lock the keys of the digital temperature controller:
• Press and hold both the key and key at the
same time for over two seconds. The message “Loc” will
appear on the display.
To unlock the keys of the digital temperature controller:
• Press and hold both the key and key at the
same time until the message “UnL” appears on the display.
Form No. GRHWM-0520
13
English
OPTIONS AND ACCESSORIES
4-Sided Sign Holder
A 4-sided sign holder is available as an accessory for the
GRHW-1SG model only. Use the following procedure to install
the 4-sided sign holder.
1. Remove the four upper screws from the top four corners of
the unit.
2. Align the bottom screw holes on the front and rear long
sign holder brackets with the screw holes on the unit.
3. Secure the two long sign holders to the unit using the
previously removed screws.
Screw
Long
Sign Holder
Installing the Front and Rear Long Sign Holders
4. Install the side sign holders to the front and rear long sign
holders. To install a side sign holder:
a. Clip the hemmed top edge the side sign holder over the
top edge of the front and rear long sign holder brackets.
At the same time, guide the threaded studs near the
bottom of the side sign holder through the mounting
holes on the front and rear long sign holder brackets.
Side Sign
Holder
Rear Long
Sign Holder
Front Long
Sign Holder
Hemmed
Edge
Hemmed
Edge
Installing a Side Sign Holder
b. Secure the side sign holder to the two long sign holders
by attaching the supplied cap nuts to the threaded studs.
Long Sign
Holder
Brackets
Side
Sign
Holder
Cap
Nut
Threaded
Stud
Securing the Side Sign Holders
4″ (102 mm) Adjustable Legs
   
for GRHW-1P and GRHW-1SG models and are standard on
GRHW-2P models.
Overhead Heat Controls
Overhead heat controls are available options for GRHW-1P,
-2P, -1SG, and -1SGS models. An infinite control allows the
     
wattage down to any desired level.
Hardcoated Bin
Hardcoated bins are available
as accessories for GRHW-1SG,
GRHW-1SGS, and GRHW-
1SGD models. The dimensions
of hardcoated bins are
    
(102 x 337 x 25 mm).
Chef LED Bulbs
Chef LED bulbs are available for all Mini-Merchandisers. Chef
LED bulbs are LED light bulbs that offer energy savings over
incandescent bulbs. Use the following for replacement bulbs:
120 Volts
2700K: R02.30.185.01
3000K: R02.30.195.01
4000K: R02.30.196.01
230 Volts
2700K: R02.30.197.01
3000K: R02.30.198.01
4000K: R02.30.199.01
14
Form No. GRHWM-0520
English
LIMITED WARRANTY
1. PRODUCT WARRANTY
Hatco warrants the products that it manufactures (the “Products”)
to be free from defects in materials and workmanship, under
normal use and service, for a period of one (1) year from the
date of purchase when installed and maintained in accordance
with Hatco’s written instructions or 18 months from the date
of shipment from Hatco. Buyer must establish the Product’s
purchase date by registering the Product with Hatco or by other
means satisfactory to Hatco in its sole discretion.
Hatco warrants the following Product components to be free
from defects in materials and workmanship from the date of

of time and on the conditions listed below:
a) One (1) Year Parts and Labor PLUS One (1) Additional
Year Parts-Only Warranty:
Conveyor Toaster Elements (metal sheathed)
Drawer Warmer Elements (metal sheathed)
Drawer Warmer Drawer Rollers and Slides
Strip Heater Elements (metal sheathed)
Display Warmer Elements (metal sheathed air heating)
Holding Cabinet Elements (metal sheathed air heating)
Heated Well Elements — HW and HWB Series
(metal sheathed)
b) Two (2) Year Parts and Labor Warranty:
Induction Ranges
Induction Warmers
c) One (1) Year Parts and Labor PLUS Four (4) Years
Parts-Only Warranty:
3CS and FR Tanks
d) One (1) Year Parts and Labor PLUS Nine (9) Years
Parts-Only Warranty on:
Electric Booster Heater Tanks
Gas Booster Heater Tanks
e) Ninety (90) Day Parts-Only Warranty:
Replacement Parts
THE FOREGOING WARRANTIES ARE EXCLUSIVE AND
IN LIEU OF ANY OTHER WARRANTY, EXPRESSED OR
IMPLIED, INCLUDING BUT NOT LIMITED TO ANY IMPLIED
WARRANTY OF MERCHANTABILITY OR FITNESS FOR
A PARTICULAR PURPOSE OR PATENT OR OTHER
INTELLECTUAL PROPERTY RIGHT INFRINGEMENT. Without
limiting the generality of the foregoing, SUCH WARRANTIES
DO NOT COVER: Coated incandescent light bulbs, fluorescent
lights, heat lamp bulbs, coated halogen light bulbs, halogen
heat lamp bulbs, xenon light bulbs, LED light tubes, glass
components, and fuses; Product failure in booster tank, fin
tube heat exchanger, or other water heating equipment caused
by liming, sediment buildup, chemical attack, or freezing;
or Product misuse, tampering or misapplication, improper
installation, or application of improper voltage.
2. LIMITATION OF REMEDIES AND DAMAGES
Hatco’s liability and Buyer’s exclusive remedy hereunder will
be limited solely, at Hatco’s option, to repair or replacement
using new or refurbished parts or Product by Hatco or a Hatco-
authorized service agency (other than where Buyer is located
outside of the United States, Canada, United Kingdom, or
Australia, in which case Hatco’s liability and Buyer’s exclusive
remedy hereunder will be limited solely to replacement of part
under warranty) with respect to any claim made within the
applicable warranty period referred to above. Hatco reserves

the context of this Limited Warranty, “refurbished” means a part
or Product that has been returned to its original specifications
by Hatco or a Hatco-authorized service agency. Hatco will not
accept the return of any Product without prior written approval
from Hatco, and all such approved returns shall be made
at Buyer’s sole expense. HATCO WILL NOT BE LIABLE,
UNDER ANY CIRCUMSTANCES, FOR CONSEQUENTIAL
OR INCIDENTAL DAMAGES, INCLUDING BUT NOT LIMITED
TO LABOR COSTS OR LOST PROFITS RESULTING FROM
THE USE OF OR INABILITY TO USE THE PRODUCTS OR
FROM THE PRODUCTS BEING INCORPORATED IN OR
BECOMING A COMPONENT OF ANY OTHER PRODUCT OR
GOODS.
Formulaire n° GRHWM-0520
15
Français
SOMMAIRE
Les Mini-présentoirs Hatco Glo-Ray
®
série GRHW maintiennent
au chaud les aliments emballés ou conditionnés dans les
zones de travail des cuisines, les stations de ramassage
des serveuses ou les points de service aux clients. Ces
présentoirs sont équipés d'une base chauffante à commande
thermostatique ainsi que d'un dispositif chauffant suspendu à
infrarouge préfabriqué pour prolonger la durée de conservation
de la plupart des aliments.
Les dispositifs chauffants infrarouge sont garantis deux ans
contre le bris et le grillage, et les dispositifs chauffants des
bases sont garantis un an contre le grillage.
Les Mini-présentoirs Hatco Glo-Ray sont le fruit de recherches
approfondies et d'essais sur le terrain. Les matériaux utilisés
ont été sélectionnés pour un maximum de durabilité, une belle
apparence et une performance optimale. Chaque appareil est
minutieusement inspecté et testé avant expédition.
Ce manuel contient des instructions relatives à l'installation,
à la sécurité et au fonctionnement des Mini-présentoirs Hatco
Glo-Ray. Hatco vous recommande de lire l’ensemble des
instructions d’installation et d’utilisation et toutes les consignes
de sécurité dans ce manuel avant d’installer et d’utiliser
l’appareil.
Les consignes de sécurité qui apparaissent dans ce manuel
sont identifiées par les mots indicateurs suivants :
AVERTISSEMENT
AVERTISSEMENT indique une situation dangereuse qui,
si elle n’est pas évitée, peut provoquer la mort ou des
blessures graves.
ATTENTION
ATTENTION indique une situation dangereuse qui, si elle
n’est pas évitée, peut provoquer des blessures légères ou
moyennes.
AVIS
AVIS est utilisé pour des questions sans rapport avec des
blessures corporelles.
Informations Importantes pour le Propriétaire ................15
Introduction .........................................................................15
Consignes de Sécurité Importantes ................................. 16
Description du Modèle .......................................................17
All Models .......................................................................... 17
Désignation du Modèle ...................................................... 18
Caractéristiques Techniques ............................................18
Configuration des Fiches ...................................................18
Tableau des Caractéristiques électriques..........................18
Dimensions ........................................................................ 19
Installation ...........................................................................20
Généralités ........................................................................20
Installation du pare-haleine ...............................................20
Installation des panneaux latéraux ....................................21
Mode d’emploi ....................................................................22
Généralités ........................................................................22
Maintenance ........................................................................23
Généralités ........................................................................23
Nettoyage quotidien ...........................................................23
Remplacement des voyants ..............................................23
 ...............23
Guide de Dépannage ..........................................................24
Options et Accessoires .....................................................25
Garantie Limitée .................................................................27
Autorisés Distributeurs de Pièces ........Couverture Arrière
INFORMATIONS IMPORTANTES POUR LE PROPRIÉTAIRE
Record the model number, serial number ((étiquette des
caractéristiques techniques située au dos de l’appareil, sur
la partie supérieure)), le voltage et la date d’achat de votre
appareil ci-dessous. Veuillez avoir cette information à portée
de la main si vous appelez Hatco pour assistance.
Modèle No. ___________________________________
Numéro de série _______________________________
Voltage ______________________________________
Date d’achat __________________________________
Enregistrez votre appareil!
Remplissez la garantie en ligne pour éviter les retards
        
www.hatcocorp.com, sélectionnez le menu déroulant
Support (Assistance), puis cliquez sur « Warranty » (Garantie).
Horaires
ouvrables : 7h00 à 17h00 du lundi au vendredi
Heure du Centre (CT)
(

7h00 à 16h00 le vendredi)
Téléphone: 800-558-0607; 414-671-6350
Courriel: [email protected]
Service d'assistance et de pièces de
rechange disponible 7j/7, 24h/24 aux
États-Unis et au Canada en composant
le 800-558-0607.
Des renseignements supplémentaires sont disponibles sur
notre site Web à www.hatcocorp.com.
INTRODUCTION
Formulaire n° GRHWM-0520
16
Français
CONSIGNES DE SÉCURITÉ IMPORTANTES
AVERTISSEMENT
DANGER DE DÉCHARGE ÉLECTRIQUE :
• Brancher l’appareil sur une prise de courant avec terre
de tension, de format et de configuration des broches
corrects. Si la fiche et la prise ne se correspondent pas,
s’adresser à un électricien qualifié pour déterminer et
installer une prise de courant de format et de tension
corrects.
• Éteignez l’appareil, débranchez le cordon d’alimentation
et laissez refroidir avant une maintenance ou un
nettoyage.
• NE PAS immerger l’appareil ni le saturer d’eau.
L’appareil n’est pas étanche à l’eau. Ne pas le faire
fonctionner s’il a été immergé ou saturé d’eau.
• L’appareil n’est pas à l’épreuve des intempéries. Placer
l’appareil à l’intérieur à une température ambiante de
21°C (70°F) minimum.
• Ne pas nettoyer à la vapeur ni utiliser trop d’eau sur
l’appareil.
• Ne pas tirer l’appareil par son cordon électrique.
• Ne pas utiliser l’appareil si le cordon est endommagé
ou usé.
• Ne pas tenter de réparer ni de changer un cordon
électrique endommagé. Ce cordon doit être changé
par Hatco, par un réparateur Hatco agréé ou par une
personnes de qualifications comparables.
• La réparation de cet appareil doit être confiée
exclusivement à du personnel qualifié. Les réparations
par des personnes non qualifiées peuvent provoquer
des décharges électriques et des brûlures.
• Pour les réparations, utiliser exclusivement des pièces de
rechange Hatco d’origine. Utilisez des pièces détachées
Hatco authentiques sous peine d’annuler toutes les ga-
ranties et d’exposer l’utilisateur à des tensions électriques
dangereuses pouvant entraîner une électrocution ou des
brûlures. Les pièces de rechange Hatco d’origine sont
conçues pour fonctionner sans danger dans les envi-
ronnements dans lesquels elles sont utilisées. Certaines
pièces de rechange génériques ou de second marché ne
présentent pas les caractéristiques leur permettant de
fonctionner sans danger dans la matériel Hatco.
DANGER D’INCENDIE: Placer l’appareil à un minimum
de 25 mm (1″) des parois et matières combustibles. Si
une distance sûre n’est pas maintenue, la chaleur peut
provoquer une combustion ou une altération de couleur.
RISQUE D’EXPLOSION: Ne conservez pas ou n’utilisez pas
d’essence ou d’autres vapeurs ou liquides inflammables à
proximité de ce four ou de tout autre appareil.
S’assurer que le produit alimentaire a été chauffé à une
température adaptée au maintien de sa salubrité avant de
le mettre sur l’appareil sous peine de risques graves pour
la santé. Cet appareil est destiné au maintien de produits
alimentaires préchauffés uniquement.
Cet appareil ne doit pas être utilisé par des enfants ou des
personnes avec des capacités physiques, sensorielles ou
mentales diminuées. Assurez-vous que les enfants sont
bien surveillés et tenez-les à l’écart de l’appareil.
AVERTISSEMENT
Assurez-vous que tous les opérateurs ont été formés à
l’utilisation sûre et correcte de l’appareil.
N’utilisez que des ampoules qui respectent ou dépassent
les normes de la National Sanitation Foundation (NSF)
et qui sont spécifiquement conçues pour les espaces
de conservation des aliments. Les bris d’une ampoule
électrique non équipée d’un revêtement adapté
peuvent provoquer des dommages corporels et/ou une
contamination des aliments.
Cet appareil ne contient aucune pièce réparable par
l’utilisateur. Si cet appareil doit être réparé, contacter un
réparateur Hatco agréé ou le Service après-vente Hatco au
800-558-0607 ou 414-671-6350.
ATTENTION
DANGER DE BRÛLURE: Certaines surfaces extérieures
de l’appareil deviennent chaudes. Toucher ces zones de
l’appareil avec précaution.
Placez l’appareil sur un plan de travail à la bonne hauteur,
à un emplacement pratique à utiliser. L'emplacement doit
être horizontal pour éviter que l'appareil ou son contenu
ne tombe accidentellement, et suffisamment solide pour
supporter le poids de l'appareil et de son contenu.
La National Sanitation Foundation (NSF) exige que les
appareils d’une largeur supérieure à 914 mm ou pesant plus de
36 kg soient fixés sur le plan de travail ou installés au-
dessus de ce dernier. Si l’appareil ne peut pas être fixé
sur l’emplacement d’utilisation, des pieds de 102 mm (4″)
sont fournis pour permettre le nettoyage en dessous de
l’appareil.
AVIS
Empêchez toute surchauffe de la plaque vitrée. La
surchauffe peut faire fondre ou ramollir les contenants
alimentaires.
Ne pas utiliser de bacs alimentaires, de plats en céramique
ou de matériaux abrasifs sur la plaque chauffante vitrée.
Cela risquerait de rayer la surface en vitrocéramique, de
la détériorer et de la rendre plus salissante. Les dégâts
occasionnés à la surface en vitrocéramique ou le bris de la
vitrocéramique dus à une utilisation inappropriée ne sont
pas couverts par la garantie.
Ne faites pas glisser de casseroles sur les surfaces
à revêtement dur, n'utilisez pas de casseroles avec
revêtement à fond dur et ne laissez rien tomber sur les
surfaces à revêtement dur. Cela risquerait de rayer
l'équipement. Les dégâts occasionnés sur les surfaces à
revêtement dur dus à une mauvaise utilisation ne sont pas
couverts par la garantie.
Ne couchez pas l’appareil sur le côté comportant le panneau
de commande. Cela pourrait endommager l’appareil.
Utilisez uniquement des nettoyants non abrasifs et des
chiffons doux. Les chiffons et nettoyant abrasifs pourraient
rayer la finition de l’unité, altérant son apparence et la
rendant vulnérable à l’accumulation de saleté.
Lisez l’information de securite importante suivante avant d’utiliser cet équipement pour éviter
des dommages ou la mort sérieux et pour éviter d’endommager l’équipement ou la propriété.
Formulaire n° GRHWM-0520
17
Français
CONSIGNES DE SÉCURITÉ IMPORTANTES
Plaque à base
chauffée
Protection individuelle
Bacs de 102 mm
Pare-haleine
Modèle GRHW-1SG
Modèles GRHW-1SGD et GRHW-1SGDS
Les modèles GRHW-1SGD et GRHW-1SDS sont dotés d'une
base chauffante en acier inoxydable ou à revêtement dur et
d'une plaque chauffante supérieure vitrée avec des panneaux
latéraux en verre.
Le modèle GRHW-1SGD est équipé d’une base chauffante
horizontale en acier inoxydable et une plaque chauffante
vitrée horizontale. Il est disponible avec une base chauffante à
revêtement dur en option.
Le modèle GRHW-1SGDS possède une base chauffante
inclinée à revêtement dur et une plaque chauffante vitrée
inclinée.
Les commandes pour les deux modèles comprennent
un interrupteur marche/arrêt éclairé, une commande de
température de la base et une commande de température
de la plaque vitrée. Un régulateur de température numérique
est disponible en option (voir chapitre OPTIONS ET
ACCESSOIRES pour plus de détails).
Plaque
chauffante
vitrée
Panneau latéral en verre
Plaque à base
chauffée
Protection
individuelle
Pare-haleine
Modèle GRHW-1SGDS
Tous les Modèles
Les Mini-présentoirs série GRHW utilisent un espace de
comptoir limité et sont disponibles dans différentes formes,
tailles et couleurs pour contenir des échantillons d'aliments,
des sandwiches et des produits emballés.
Tous les modèles GRHW sont équipés d'une base
chauffante à commande thermostatique, d'un pare-haleine,
de dispositifs chauffants supérieurs à infrarouge, de
voyants supérieurs, en option Couleurs design, cordon de
1 829 mm et prise d’alimentation.
NOTA: Pour plus de détails, consultez le chapitre OPTIONS
ET ACCESSOIRES.
Modèles GRHW-1P et GRHW-2P
Les modèles GRHW-1P et GRHW-2P sont des réchauds pour
Sandwiches. Le GRHW-1P a une capacité d'un seul bac avec
des pieds en caoutchouc de 25 mm. Le GRHW-2P a une
capacité de deux bacs avec des pieds réglables de 102 mm.
Les commandes des deux modèles comprennent un
interrupteur à bascule lumineux ON/OFF, une commande de
température de la base, un interrupteur à bascule ON/OFF
(I/O) et une commande de température du dispositif chauffant
suspendu en option.
Plaque à base
chauffée
Pare-haleine
Modèle GRHW-1P
Modèles GRHW-1SG et GRHW-1SGS
Les modèles GRHW-1SG et GRHW-1SGS sont équipés
de protections individuelles et de cinq bacs de 102 mm.
Le GRHW-1SG a une base chauffante horizontale et le
GRHW-1SGS a une base chauffante inclinée et des panneaux
latéraux en polycarbonate.
Un porte-étiquette à 4 faces et des pieds réglables de
102 mm sont disponibles pour le modèle GRHW-1SG en tant
qu'accessoires.
Les commandes des deux modèles comprennent un
interrupteur à bascule lumineux ON/OFF, une commande de
température de la base, un interrupteur à bascule ON/OFF
(I/O) et une commande de température du dispositif chauffant
suspendu en option.
DESCRIPTION DU MODÈLE
AVIS
IMPORTANT: N'utilisez PAS de serviettes en papier ou
de nettoyant pour vitres pour nettoyer les surfaces en
polycarbonate. Les serviettes en papier et le nettoyant
pour vitres risquent de rayer l'équipement. Essuyez les
surfaces en polycarbonate à l'aide d'un chiffon humide
doux et propre.
AVIS
Pour déplacer ou installer l'appareil, ne le traînez pas et
ne le faites pas glisser. Soulevez-le avec précaution afin
d'éviter que les pieds en caoutchouc ne se détachent.
Formulaire n° GRHWM-0520
18
Français
Modéle Tension Intensité Amps Configuration de Fiches Poids d’embarquement
GRHW-1P 120 820 6.8 NEMA 5-15P
16 kg (35 lbs.)
220 782 3.6 CEE 7/7 Schuko or BS-1363
240 838 3.5 CEE 7/7 Schuko or AS 3112
220–230 782–855 3.6–3.7 CEE 7/7 Schuko
230–240 770–838 3.3–3.5 BS-1363
GRHW-2P 120 1640 13.7 NEMA 5-15P *
31 kg (67 lbs.)
220 1560 7.1 CEE 7/7 Schuko or BS-1363
240 1680 7.0 CEE 7/7 Schuko or AS 3112
220–230 1560–1705 7.1–7.4 CEE 7/7 Schuko
230–240 1543–1680 6.7–7.0 BS-1363
GRHW-1SG 120 820 6.8 NEMA 5-15P
17 kg (37 lbs.)220 782 3.6 CEE 7/7 Schuko
240 838 3.5 BS-1363
GRHW-1SGS 120 820 6.8 NEMA 5-15P
18 kg (40 lbs.)220
820
3.7 CEE 7/7 Schuko
240 3.4 BS-1363
GRHW-1SGD 120 1330 11.1 NEMA 5-15P 33 kg (73 lbs.)
GRHW-1SGDS
120 1330 11.1 NEMA 5-15P 33 kg (73 lbs.)
DÉSIGNATION DU MODÈLE
G R H W - x P
Glo-Ray
P = Bacs
SG = Plaque simple horizontale
SGS = Plaque simple inclinée
SGD = Double plaque horizontale avec
Plaque chauffante supérieure vitrée
SGDS = Double plaque inclinée avec
Plaque chauffante supérieure vitrée
Réchaud pour Sandwiches/
Mini-Présentoir
Nombre de Bacs
CARACTÉRISTIQUES TECHNIQUES
Configuration des fiches
Les appareils sont fournis par l’usine avec un cordon et une
     
fonction de l’application.
AVERTISSEMENT
DANGER DE DÉCHARGE ÉLECTRIQUE: Brancher
l’appareil sur une prise de courant avec terre de tension,
de format et de configuration des broches corrects. Si la
fiche et la prise ne se correspondent pas, s’adresser à un
électricien qualifié pour déterminer et installer une prise de
courant de format et de tension corrects.
NOTA: L'étiquette des caractéristiques techniques se trouve
au dos de l'appareil, sur la partie supérieure. Reportez-
vous à l’étiquette du numéro de série et les données
électriques de l’appareil.
NEMA 5-15P
CEE 7/7 Schuko AS-3112
BS-1363
NEMA 5-20P
Configuration des fiches
NOTA: Prise non fournie par Hatco.
Tableau des Caractéristiques électriques
Les informations électriques grisées dans le tableau désignent les modèles destinés à internationaux uniquement.
* NEMA 5-20P pour le Canada.
NOTA: Les poids d’expédition sont estimés.
Formulaire n° GRHWM-0520
19
Français
Modéle
Largeur
(A)
Profondeur
(B)
Hauteur
(C)
Empattement
Largeur (D)
Empattement
Profondeur (E)
GRHW-1P 565 mm
(22-1/4)
486 mm
(19-1/8)
451 mm
†
(17-3/4
505 mm
(19-7/8)
289 mm
(11-3/8)
GRHW-2P 1099 mm
(43-1/4)
486 mm
(19-1/8)
527 mm
(20-3/4)
1038 mm
(40-7/8)
289 mm
(11-3/8)
GRHW-1SG 565 mm
(22-1/4)
486 mm
(19-1/8)
451 mm
†
(17-3/4
505 mm
(19-7/8)
289 mm
(11-3/8)
GRHW-1SGS 565 mm
(22-1/4)
486 mm
(19-1/8)
464 mm
(18-1/4)
505 mm
(19-7/8)
289 mm
(11-3/8)
GRHW-1SGD 581 mm
(22-7/8)
521 mm
(20-1/2)
597 mm
(23-1/2)
505 mm
(19-7/8)
289 mm
(11-3/8)
GRHW-1SGDS 578 mm
(22-3/4)
534 mm
(21)
600 mm
(23-5/8)
505 mm
(19-7/8)
289 mm
(11-3/8)
CARACTÉRISTIQUES TECHNIQUES
Dimensions
$
&
(
%
'
9XHGHF{Wp9XHGHIDFH
GRHW-1P, -2P, -1SG, et -1SGS Dimensions
†

hauteur (C) si vous utilisez les pieds de 102 mm.
Vue de côtéVue de face
A
C
E
B
D
GRHW-1SGD et GRHW-1SGDS Dimensions
Formulaire n° GRHWM-0520
20
Français
INSTALLATION
5. Serrez les vis moletées maintenant les protections

en place, le case échéant.
6. Placer l’appareil à l’endroit souhaité. Cette étape nécessite
deux personnes.
• Placez l’appareil à un endroit où la température ambiante
est constante et de 21°C (70°F) minimum. Évitez les
endroits susceptibles d’activer les mouvements ou les
courants d’air (proximité des ventilateurs ou hottes
d’évacuation et conduites de climatisation).
• Assurez-vous que l’appareil est à la bonne hauteur
du plan de travail dans un espace pratique pour son
utilisation.
• Veillez à ce que le plan de travail soit horizontal et
suffisamment solide pour supporter le poids de l’appareil
et des aliments.
Installation du pare-haleine
Tous les modèles sont livrés avec des pare-haleine. Utilisez
la procédure appropriée pour installer un pare-haleine sur un
appareil.
NOTA: Veillez à installer le pare-haleine avant d'installer les
panneaux latéraux, le cas échéant.
Modèles GRHW-1P, -2P, -1SG, et -1SGS
1. Faites passer chacune des vis à souder par le dessus du
pare-haleine et au travers de la barre de soutien. Vissez
sans le serrer un écrou borgne sur chacune des vis à
souder au-dessous de la barre de soutien.
2. Soulevez l'ensemble pare-haleine et glissez
soigneusement chacune des vis à souder attachées, sans
être serrées, au pare-haleine dans la rainure sur l'appareil.
3. Alignez chaque extrémité du pare-haleine avec les
extrémités de l'appareil, puis serrer les écrous borgnes
pour fixer le pare-haleine en position. Ne serrez pas trop
les écrous borgnes.
Écrou borgne
Barre de
soutien
Pare-haleine
Rainure
Rainure
Vis à
souder
Installation d’un pare-haleine
(modèle GRHW-1SG illustré)
Généralités
Glo-Ray
®
Les Mini-présentoirs série GRHW sont expédiés avec
la plupart des composants pré-assemblés. Faites attention
lors du déballage pour éviter d’endommager l’appareil et ses
composants.
AVERTISSEMENT
DANGER DE DÉCHARGE ÉLECTRIQUE : L’appareil n’est
pas à l’épreuve des intempéries. Placer l’appareil à l’in-
térieur à une température ambiante de 21°C (70°F) minimum.
DANGER D’INCENDIE : Placer l’appareil à un minimum
de 25 mm des parois et matières combustibles. Si une dis-
tance sûre n’est pas maintenue, la chaleur peut provoquer
une combustion ou une altération de couleur.
ATTENTION
Placez l'appareil à une hauteur de comptoir adaptée
et sur un emplacement pratique pour son utilisation.
L'emplacement doit être horizontal pour éviter que
l'appareil ou son contenu ne tombe accidentellement, et
suffisamment solide pour supporter le poids de l'appareil
et de son contenu.
La National Sanitation Foundation (NSF) exige que les
appareils d’une largeur supérieure à 914 mm ou pesant plus de
36 kg soient fixés sur le plan de travail ou installés au-
dessus de ce dernier. Si l’appareil ne peut pas être fixé sur
l’emplacement d’utilisation, des pieds de 102 mm (4″) sont
fournis pour permettre le nettoyage en dessous de l’appareil.
AVIS
Pour déplacer ou installer l'appareil, ne le traînez pas et
ne le faites pas glisser. Soulevez-le avec précaution afin
d'éviter que les pieds en caoutchouc ne se détachent.
1. Retirer l’appareil de sa boîte.
NOTA: Pour éviter un retard de service sous garantie,
enregistrez la garantie en ligne. Pour des détails, voir
la section INFORMATIONS IMPORTANTES POUR LE
PROPRIÉTAIRE.
2. Retirer le ruban et le film de protection de toutes les
surfaces de l’appareil.
3. Installez le pare-haleine. Reportez-vous à la procédure
« Installation du pare-haleine » du présent chapitre.
4. Installez les panneaux latéraux, le cas échéant. Reportez-
vous à la procédure « Installation des panneaux latéraux
» du présent chapitre.
Vis moletée
Protection
individuelle
Installation des protections individuelles (modèle GRHW-1SG illustré)
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
La page charge ...
  • Page 1 1
  • Page 2 2
  • Page 3 3
  • Page 4 4
  • Page 5 5
  • Page 6 6
  • Page 7 7
  • Page 8 8
  • Page 9 9
  • Page 10 10
  • Page 11 11
  • Page 12 12
  • Page 13 13
  • Page 14 14
  • Page 15 15
  • Page 16 16
  • Page 17 17
  • Page 18 18
  • Page 19 19
  • Page 20 20
  • Page 21 21
  • Page 22 22
  • Page 23 23
  • Page 24 24
  • Page 25 25
  • Page 26 26
  • Page 27 27
  • Page 28 28

Hatco GRHW Series Le manuel du propriétaire

Hatco
Marque
Hatco
Modèle
GRHW Series
Taper
Le manuel du propriétaire
Télécharger le PDF
rapport

dans d''autres langues

Documents connexes

Autres documents