LAM6XXX
www.howdens.com/appliance-registration
Built-Under
Larder Fridge / Fridge / Freezer
Generic instructions, (To be used in conjunction with User Instructions).
l Please read this Installation Manual to ensure safe fitting and use of the appliance.
l The appliance should be fitted by a suitably competent and qualified person.
l Please keep these instructions in a safe place for future reference.
l Danger of suffocation keep packaging material away from children.
Installation Instructions
ISSUE v1.2 101023
2www.howdens.com
AB
Screw hole
plug
Screw hole
cover
Remove parts bag and trim
from the appliance.
DO NOT use high speed
impact power tools.
2mm drill bit
3.5x13
3.9x13 FH
TORX25
and
cross head
screw driver
Bracket and
cover x2
Extension feet x4
Plastic trim
Cover caps x4
Installation
GenericinstructionsforttingaLarderFridge/Fridge/Freezer.
(Fridge shown for illustrative purposes only)
Tools required
Parts supplied - PLEASE RETAIN, DO NOT THROW AWAY!
3
Exclusive to Howdens
820 - 920mm
(890mm Howdens
standard install)
min
575mm
600mm
(+2mm)
Position the appliance relative to service
connections.
Prepare cabinet niche
It is critical that
the appliance is
installed level.
Worktop
WARNING!
Appliance must be
earthed. Socket must
be accessible after fitting.
WARNING!
Do not use extension
cable or adapters.
Note: For profile kitchens -
insert 18mm board below
worktop, level with bottom
edge of front panel.
Note:
If opening against a wall, 180mm
clearance is required to allow
the baskets to be removed.
180mm
180mm
4www.howdens.com
1
2
Reverse door opening, (if applicable), DO IT NOW.
(Handle door with care)
1 - Ensure the appliance is not connected to a power supply.
3 - Remove door and keep in a safe place.
2 - Remove door hinge screws and keep in a safe place for future use.
Remove all contents
and door balconies,
(if applicable).
(See also ‘Reversing
Inner Freezer Door’).
WARNING:
Support door
when removing
hinge screws.
5
Exclusive to Howdens
1
2
3
1
2
4
3
x2 pieces
4 - Remove hinges, plastic cover caps and plugs. Keep in a safe place for future use.
5 - Remove side xing brackets and re-position to opposite side.
Note:
When retting the hinges;
Top right hinge will be tted
bottom left.
Bottom right hinge will be
tted top left.
6www.howdens.com
1
2
Ret x2 pieces
3
1
2
6 - Re-position hinges, plastic cover caps and plugs.
7 - Carefully ret door and replace door balconies.
Note:
Ret bottom right hinge
to top left.
Ret top right hinge
to bottom left.
WARNING:
Support door
when retting.
(See also ‘Reversing
Inner Freezer Door’).
7
Exclusive to Howdens
2 - Attach top trim.
1
1
c.65mm
x2
2
A
Howdens standard worktop install height (890mm),
(Fridge shown for illustrative purposes only)
1 - Attach extension feet and adjust to c.65mm.
Tip: Use masking
tape to stop feet
dropping out.
IMPORTANT: Do not use extension feet for Prole
Kitchens and when tting a granite/solid surface
worktop, see stages 5d/5e.
CAUTION: When extension
feet are tted move with
care to avoid damage.
8www.howdens.com
4 - Raise feet so that the top trim engages with the underside of the worktop.
Ensure the appliance is level and true.
Adjust appliance
height if necessary
Worktop to brackets c.12mm
top of bracket to underside
of worktop.
c.40mm c.40mm
3 - Move into position.
WARNING:
Take care not to damage
appliance or surrounding
cabinetry.
Do not trap electric cable.
Appliance depth in niche - from cabinet edge to
appliance body when door is open.
9
Exclusive to Howdens
167.5mm 25mm
335mm
649mm
2
1
x4
3
x4
= =
A
A
5a - Prepare decor door frontal
Slab door frontal
Mark xing positions.
Do not attach
brackets to frontal.
If applicable, t door
handle at this stage
using countersink screws.
Loosen top bracket
screws and slide
left/right to achieve
frontal alignment.
Secure when
positioned correctly.
Attach door, using
top brackets only,
1 x screw only at 1st.
Secure bottom
brackets.
10 www.howdens.com
167.5mm 55mm
39mm335mm
650mm
1
2
x4
x4
= =
A
A
5b - Prepare decor door frontal, (continued)
Integrated handle door frontal
Secure bottom
brackets.
Attach frontal to
the appliance door
and slide left/right
to achieve frontal
alignment.
Secure when
positioned correctly.
Invert bracket.
Mark xing positions.
Remove top door brackets from appliance,
invert and attach to the door.
Do not attach the bottom
brackets to the frontal.
11
Exclusive to Howdens
2
3
167.5mm 25mm
335mm
x4
1
x4
= =
A
A
5c - Prepare decor door frontal, (continued)
Shaker door frontal,
(use bracket LAM0060)
Mark xing positions.
Do not attach
brackets to frontal.
If applicable, t door
handle at this stage
using countersink screws.
Remove the existing
bottom brackets from the
appliance door and t the
‘Shaker door bracket’.
Secure shaker door bracket,
(use inner x2 holes and
outer x2 holes).
Attach door, using
top brackets only,
1 x screw only at 1st.
Shaker door
bracket.
Loosen top bracket
screws and slide
left/right to achieve
frontal alignment.
Secure when
positioned correctly.
12 www.howdens.com
2
3
167.5mm 43mm
335mm
667mm
x4
1
x4
c.47mm
= =
A
A
5d - Prepare decor door frontal, (continued)
Prole Kitchen door frontal
Mark xing positions.
Do not attach
brackets to frontal.
If applicable, t door
handle at this stage
using countersink screws.
Do not use extension
feet, adjust to c.47mm.
Secure bottom
brackets.
Attach door, using
top brackets only,
1 x screw only at 1st.
Loosen top bracket
screws and slide
left/right to achieve
frontal alignment.
Secure when
positioned correctly.
13
Exclusive to Howdens
2
167.5mm 33mm
335mm
657mm
1
(3.9x13 FH) x4
c.55mm
Rear - Timber
support
Front - Metal
bar support
3
x4
= =
(3.9x13 FH) x4
A
A
Granite worktop application,
door frontal
Mark xing positions.
Do not attach
brackets to frontal.
If applicable, t door
handle at this stage
using countersink screws.
Do not use extension
feet, adjust to c.55mm.
5e - Prepare decor door frontal, (continued)
Secure bottom
brackets.
Attach door, using
top brackets only,
1 x screw only at 1st.
Loosen top bracket
screws and slide
left/right to achieve
frontal alignment.
Secure when
positioned correctly.
IMPORTANT:
Support granite
worktop across
opening.
14 www.howdens.com
B
x4
Brackets x2
1
2
6 - Door frontal alignment.
7 - Loosely attach plastic slider brackets. Take care not to move the appliance.
WARNING:
Take care not to damage
frontals and surrounding
cabinetry.
If necessary, make minor
adjustment so the door
frontal is aligned with the
door frontals alongside.
15
Exclusive to Howdens
x2
1
2
x2
1
2
B
A
8 - Secure hinge side brackets. Take care not to move the appliance.
9 - Fix non hinge side brackets. Take care not to move the appliance.
16 www.howdens.com
Covers x2
1
2
1
2
10 - Secure non hinge side brackets. Take care not to move the appliance.
11 - Fix cover caps.
17
Exclusive to Howdens
2
1
Cover caps x4
Decorative PlinthStandard Plinth
WARNING: Ensure the appliance ventilation grilles are not covered.
Ensure fridge vents
are not covered.
Cut plinth and fit a
suitable grille.
12 - Fit door bracket cover caps.
13 - Fit plinth and grille (if necessary).
18 www.howdens.com
3
2
Fit plastic plugs x2
1
1 - Open inner freezer door, remove screws and door catch, note orientation of catch.
2 - Remove screw and hinge pivots, 1, 2, 3.
Reverse inner freezer door, (if applicable).
(Handle freezer box door with care)
WARNING:
Support freezer
box door when
removing.
Remove upper hinge pivot and
insert into opposite side, 3.
19
Exclusive to Howdens
1
1
4
32
5
3 - Carefully, using a centre punch or pilot drill the pre-marked holes on the side wall, 1.
Fit door catch to side wall, (note orientation), and insert plastic plug in redundant hole.
4 - Carefully, using a centre punch or pilot drill the pre-marked hole on the side wall, 1.
Insert upper hinge pivot, 2.
Insert door into upper hinge pivot and raise lower hinge pivot to door pin, 3, 4.
Screw lower door hinge pivot into position, 5.
5 - Check and conrm correct operation of inner freezer door.
Product serial number
(Place sticker here)
Product information correct at the time of publication in October 2023.
The company has a policy of continuous product development and
reserves the right to change any products and specications given in
this manual. Subject to the Terms and Conditions of Trading, a copy of
the Howdens Terms and Conditions is available upon request.
Copyright © 2023 Howden Joinery Ltd. All rights reserved.
Howden Joinery Ltd.
Thorpe Road, Howden, East Yorkshire. DN14 7PA England
Howdens Cuisines SAS. Z.A. du Bois Rigault Nord,
1 Rue Calmette, 62880 Vendin-le-Vieil, Cedex, France
Cet appareil
se recycle
Points de collecte sur www.quefairedemesdechets.fr
Privilégiez la répara�on ou le don de votre appareil!
À DÉPOSER
EN DÉCHÈTERIE
À DÉPOSER
EN MAGASIN
OU
REPRISE
À LA LIVRAISON
OU
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
LAMONA LAM6401 Le manuel du propriétaire
- Taper
- Le manuel du propriétaire
dans d''autres langues
- English: LAMONA LAM6401 Owner's manual