Hach DR 3900 Basic User Manual

DOC022.97.90324

DR 3900

11/2017, Edition 7

Basic User Manual en

Manuel d'utilisation de base fr

Manual básico del usuario es

Manual do utilizador básico pt

基本用户手册 zh

基本ユーザーマニュアル ja

기본 사용 설명서 ko

English ............................................................................................................................................................. 3

Français ........................................................................................................................................................ 23

Español ........................................................................................................................................................ 43

Português .................................................................................................................................................... 65

中文 ................................................................................................................................................................ 85

日本語 .......................................................................................................................................................... 103

한국어 .......................................................................................................................................................... 123

English 3

English

Specifications

These are subject to change without notice!

Performance specifications

Operating mode Transmittance (%), Absorbance and Concentration

Source lamp Halogen lamp

Wavelength range 320–1100 nm

Wavelength Accuracy ± 1.5 nm (wavelength range 340–900 nm)

Wavelength

reproducibility

± 0.1 nm

Wavelength resolution 1nm

Wavelength calibration Automatic

Wavelength selection Automatic, based on method selection

Scanning speed ≥ 8 nm/s (in steps of 1 nm)

Spectral bandwidth 5nm

Photometric measuring

range

± 3.0 Abs (wavelength range 340–900 nm)

Photometric accuracy

5 m Abs at 0.0–0.5 Abs

1% at 0.50–2.0 Abs

Photometric linearity

< 0.5% to 2 Abs

≤1% at > 2 Abs with neutral glass at 546 nm

Stray light < 0.1% T at 340 nm with NaNO

2

Data log

2000 readings (Result, Date, Time, Sample ID,

User ID)

User programs 100

Physical and environmental specifications

Width 350 mm (13.78 in)

Height 151 mm (5.94 in)

Depth 255 mm (10.04 in)

Mass 4200 g (9.26 lb)

Ambient operating

requirements

10–40 °C (50–104 °F), maximum 80% relative

humidity (without condensate formation)

Ambient storage

requirements

–40–60 °C (–40–140 °F), maximum 80% relative

humidity (without condensate formation)

Additional technical data

Power connector via

external power supply

Input:100–240 V/50–60 Hz

Output: 15 V/40 VA

Interfaces

Use only shielded cable with maximum length of 3 m:

2x USB type A

1x USB type B

Use only shielded cable (e.g. STP, FTP, S/FTP) with

maximum length of 20 m:

1x Ethernet

Enclosure rating IP40 (excluding interfaces and power supply)

Protection class Class I

This product has been tested to the requirements of

CAN/CSA-C22.2 No. 61010-1, second edition,

including Amendment 1, or a later version of the same

standard that incorporates the same level of testing

requirements.

Performance specifications

English 4

General Information

Safety information

Please read this entire manual before unpacking, setting up, or

operating this equipment. Pay attention to all danger and caution

statements. Failure to do so could result in serious injury to the operator

or damage to the equipment.

To make sure that the protection provided by this instrument is not

impaired, do not use or install this instrument in any manner other than

that specified in these operating instructions.

Note: Information that supplements points in the main text.

Precautionary labels

Read all labels and tags attached to the instrument. Personal injury or

damage to the instrument could occur if this information is not observed.

A symbol, if noted on the instrument, will be included with a danger or

caution statement in the operating instructions.

RFID module (not available on all models)

RFID technology is a radio application. Radio applications are subject to

national conditions of authorisation. The use of the DR 3900 (model with

RFID module) is currently permitted in the following countries: EU, CH,

NO, HR, RS, MK, TR, CY, US, CA, AU, NZ. The manufacturer advises

that the use of the DR 3900 (model with RFID module) outside of the

above-mentioned regions may contravene national laws. The

manufacturer reserves the right also to obtain authorisation in other

countries. In case of doubt, please contact the distributor.

The DR 3900 contains an RFID module to receive and transmit

information and data. The RFID module operates with a frequency of

13.56 MHz.

Follow the following safety information, in addition to any local guidelines

in force.

DANGER

Indicates a potentially or imminently hazardous situation that, if not avoided,

results in death or serious injury.

WARNING

Indicates a potentially or imminently hazardous situation that, if not avoided, may

result in death or serious injury.

CAUTION

Indicates a potentially hazardous situation that may result in minor or moderate

injury.

NOTICE

Indicates a situation that, if not avoided, could result in damage to the instrument.

Information that requires special emphasis.

This symbol, if noted on the instrument, references the user manual

for operation and/or safety information.

Electrical equipment marked with this symbol may not be disposed of

in European domestic or public disposal systems after 12 August

2005. In conformity with European local and national regulations

(EU Directive 2002/96/EC), European electrical equipment users

must now return old or end-of life equipment to the manufacturer for

disposal at no charge to the user.

Note: For return for recycling, please contact the equipment

manufacturer or supplier for instructions on how to return

end-of-life equipment, manufacturer-supplied electrical

accessories, and all auxiliary items for correct disposal.

WARNING

The spectrophotometer may not be used in dangerous environments.

The manufacturer and its suppliers reject any express or indirect guarantee for

the use with High Risk Activities.

English 5

Safety information for the correct use of the instrument:

• Do not operate the instrument in hospitals or comparable

establishments in proximity to medical equipment, like pace makers

or hearing aids.

• Do not operate the instrument near highly flammable substances,

such as fuels, highly combustible chemicals and explosives.

• Do not operate the instrument near combustible gases, vapors or

dust.

• Do not vibrate or jolt the instrument.

• The instrument can cause interference in immediate proximity to

televisions, radios and computers.

• Do not open the instrument.

• Improper use of the instrument voids the warrantee.

Certification (integrated RFID module)

FCC ID: YUH-QR15HL

IC : 9278A-QR15HL

This device complies with Part 15 of the FCC rules and Industry Canada

license exempt RSS standard(s).

Operation is subject to the following two conditions:

1. this device may not cause interference, and

2. this device must accept any interference, including interference that

may cause undesired operation of the device."

Changes or modifications to this equipment not expressly approved by

the party responsible for compliance could void the user's authority to

operate the equipment.

This equipment has been tested and found to comply with the limits for a

Class A digital device, pursuant to Part 15 of the FCC rules. These limits

are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial

environment. This equipment generates, uses and can radiate radio

frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is

likely to cause harmful interference, in which case the user will be

required to correct the interference at their expense. The following

techniques can be used to reduce interference problems:

1. Disconnect the equipment from its power source to verify that it is

or is not the source of the interference.

2. If the equipment is connected to the same outlet as the device

experiencing interference, connect the equipment to a different

outlet.

3. Move the equipment away from the device receiving the

interference.

4. Reposition the receiving antenna for the device receiving the

interference.

5. Try combinations of the above.

Chemical and Biological Safety

Normal operation of this instrument may involve the use of hazardous

chemicals or biologically harmful samples.

• Observe all cautionary information printed on the original solution

containers and safety data sheet prior to their use.

• Dispose of all consumed solutions in accordance with national

regulations and laws.

• Select the type of protective equipment suitable to the concentration

and quantity of the dangerous material at the respective work place.

Overview of product

The DR 3900 is a VIS spectrophotometer with a wavelength range of

320 to 1100 nm. The instrument is delivered with a complete series of

application programs and supports several languages.

DANGER

Potential danger in the event of contact with chemical/biological materials.

Handling chemical samples, standards and reagents can be dangerous.

Familiarise yourself with the necessary safety procedures and the correct

handling of the chemicals before the work and read and follow all relevant safety

data sheets.

English 6

The spectrophotometer DR 3900 contains the following programs and

operating types:

• Stored programs (pre-installed tests)

• Barcode Programs

• User Programs

• Favorites

• Single Wavelength

• Multi Wavelength

• Wavelength Scan

• Time course

The DR 3900 Spectrophotometer provides digital readouts in direct

concentration units, absorbance or percent transmittance.

When selecting a user-generated or programmed method, the menus

and prompts serve to direct the user through the test.

This menu system can also generate reports, statistical evaluations of

generated calibration curves and to report instrument diagnostic checks.

Installation

Unpack the instrument

The DR 3900 Spectrophotometer comes packaged with the following

items:

• DR 3900 spectrophotometer

• Dust Cover

• USB dust cover, fitted as standard

• Benchtop power supply with power cord for US, GB

• Cell adapter A

• Light shield, fitted as standard in the DR 3900

• Operator RFID tag (not available on all models)

• Basic operating instructions DR 3900, operating instructions

LINK2SC

Further information, detailed user manuals and documentation are

available on the website of the manufacturer.

Note: If any of these items are missing or damaged, please contact the

manufacturer or a sales representative immediately.

WARNING

Electrical and fire hazards.

Only use the supplied benchtop power supply LZV844.

Only qualified experts may perform the tasks described in this section of the

manual, while adhering to all locally valid safety regulations.

English 7

Operating environment

Note the following points so that the instrument will operate perfectly and

have a long service life.

• Place the instrument firmly on an even surface. Do not push any

objects under the instrument.

• The ambient temperature must be 10–40 °C (50–104 °F).

• The relative humidity should be less than 80%; moisture should not

condense on the instrument.

• Leave at least a 15 cm clearance at the top and on all sides for air

circulation, to avoid overheating of electrical parts.

• Do not operate or store the instrument in extremely dusty, humid or

wet locations.

• Keep the surface of the instrument, the cell compartment and all

accessories clean and dry at all times. Immediately remove

splashes or spilt materials on or in the instrument.

NOTICE

Protect the instrument from extreme temperatures from heaters, direct sunlight

and other heat sources.

English 8

Front and back view

Figure 1 Front view

1 USB port type A 4 On/off switch

2 Cell compartment cover

5 RFID module (not available on all models)

3 Touch screen

English 9

Figure 2 Back view

1 Ethernet port 3 USB port type A

2 USB port type B 4 Connection for benchtop power supply

English 10

Figure 3 Cell compartments

1 Cell compartment for round cells (1) 2 Cell compartment for rectangular cells (2)

English 11

Power connections

1. Connect the power cable to the benchtop power supply.

2. Plug the benchtop power supply cable into the back of the

instrument (Figure 2, page 9).

3. Insert the power cable plug into a mains socket (100–240 V~/

50–60 Hz).

Turn on the power button next to the display to turn on the power supply

(Figure 1, page 8).

Startup

Switch on the instrument, startup process

1. Connect the power cable to the mains outlet.

2. Switch on the instrument by using the power button next to the

display.

3. The instrument starts automatically with a startup process lasting

approximately 45 seconds. The display shows the logo of the

manufacturer. At the end of the startup process, a startup melody is

heard.

Note: Wait approximately 20 seconds before switching on again so as

not to damage the electronics and mechanics of the instrument.

Language selection

The DR 3900 software includes several language options. The first time

the instrument is switched on, the language selection screen will be

shown automatically after the startup process.

1. Select the required language.

2. Press OK to confirm the language selection. The self-check will

then start automatically.

Change the language setting

The instrument functions in the selected language until the option is

changed.

1. Turn the instrument on.

2. During the startup process, touch any point on the screen and

maintain contact until the option for selecting a language is shown

(approximately 45 seconds).

3. Select the required language.

4. Press OK to confirm the language selection. The self-check will

then start automatically.

WARNING

Electrical and fire hazards.

Only use the supplied benchtop power supply LZV844.

English 12

Self-check

Each time the instrument is powered up, a test program begins.

This procedure, which takes approximately two minutes, checks the

system, lamp, filter adjustment, wavelength calibration and voltage.

Each test that functions correctly is marked accordingly.

The Main Menu is displayed when diagnostics are completed.

Note: In the event of further error messages during the test program,

refer to Troubleshooting, page 19.

Sleep mode

The instrument can be put into sleep mode.

1. Briefly press the power button next to the display.

The "Sleep mode" message is shown. The display will then switch

off automatically.

2. To switch on, press the power button next to the display.

The self-check will start automatically.

After that, the instrument is ready to use.

Power off the instrument

1. Press the power button next to the display for approximately

5 seconds.

English 13

Standard programs

Tips for the use of the touch screen

The whole screen responds to touch. To choose an option, tap with a

fingernail, fingertip, an eraser or a specialised stylus. Do not press the

screen with a sharp object, such as the tip of a ballpoint pen.

• Do not place anything on top of the screen, to prevent damage or

scratches on the screen.

• Press buttons, words or icons to select them.

• Use scroll bars to move up and down long lists very quickly. Press

and hold the scroll bar, then move up or down to move through the

list.

• Highlight an item from a list by pressing it once. When the item has

been successfully selected, it will be displayed as reversed text

(light text on a dark background).

Use of the alphanumeric keypad

This display is used to enter letters, numbers and symbols as needed

when programming the instrument. Unavailable options are disabled

(grayed out). The icons on the right and left of the screen are described

in Table 1.

The central keypad changes to reflect the chosen entry mode. Press a

key repeatedly until the desired character appears on the screen. A

space can be entered by using the underscore on the YZ_ key.

Press Cancel to cancel an entry, or press OK to confirm an entry.

Note: It is also possible to use a USB keyboard (with US keyboard

layout) or a hand-held USB barcode scanner.

Table 1 Alphanumeric keypad

Icon / key Description Function

ABC/abc Alphabetic

Toggles the character input mode between upper

and lower case.

# % Symbols

Punctuation, symbols and numerical sub- and

superscripts may be entered.

123 Numeric For entering regular numbers.

CE Clear Entry Clear the entry.

Left Arrow Back

Deletes the current character and goes back one

position.

Right

Arrow

Next Navigates to the next space in an entry.

English 14

Main menu

A variety of modes may be selected from the Main Menu. The following

table briefly describes each menu option.

There is a toolbar on the right-hand side of the screen. Press to activate

the various functions.

Table 2 Main Menu options

Option Function

Stored

Programs /

Barcode

Programs

Stored programs are pre-programmed methods that make

use of HACH chemicals and vial tests.

Further information, as well as illustrated, step-by-step pro-

cess instructions for analyses using HACH programs, are

available on the website of the manufacturer.

User Programs

User programs make "made to measure analysis" possible:

• Users can program methods they have

developed themselves

• Existing HACH methods can be stored as user

programs.

Favorites

List of methods/tests created by the user to suit his own

requirements.

Single

Wavelength

Single wavelength readings are:

Absorbance readings: The light absorbed by the sample is

measured in absorbance units.

Transmittance reading (%): Measures the percent of the

original light that passes through the sample and reaches the

detector.

Concentration readings: A concentration factor can be

entered to enable the measured absorbance values to be

converted into concentration values.

Multi

Wavelength

In the Multi Wavelength mode, absorbance (Abs) or

percentage transmittance (%T) is measured at up to four

wavelengths and absorbance differences and absorbance

relationships are calculated. Simple conversions into

concentrations can also be carried out.

Wavelength

Scan

A wavelength scan shows how the light from a sample is

absorbed over a defined wavelength spectrum. This function

can be used to determine the wavelength at which the maxi-

mum absorbance value can be measured. The absorbance

behavior is displayed graphically during the scan.

Time course

The time scan records the absorbance or % transmittance at

a wavelength over a defined time.

System checks

The "System check" menu offers a number of options,

including optical checks, output checks, lamp history,

instrument update, service time, settings for analytical

quality assurance and instrument backup.

Recall

measurement

data

Stored data can be called up, filtered, sent and deleted.

Instrument

Setup

In this mode, user-specific or method-specific settings can be

entered: operator ID, sample ID, date & time, sound, PC &

printer, password, energy-saving mode and stored data.

Table 2 Main Menu options

Option Function

English 15

Save, recall, send and delete data

The data log

The data log can store up to 2000 readings saved by the following

programs:

• Stored Programs,

• Barcode Programs,

• User programs,

• Favorites,

• Single Wavelength and

• Multi Wavelength.

A complete record of the analysis is stored, including the Date, Time,

Results, Sample ID and Operator ID.

Recall stored data from the data log

1. Press Recall Data in the Main Menu.

2. Press Data Log.

A listing of the stored data is displayed.

3. Press Filter: On/Off.

The function Filter Settings is used to search for specific items.

4. Activate On. The data can now be filtered using the following

selection criteria.

• Sample ID

• Operator ID

• Start Date

• Parameter

or any combination of the four.

English 16

5. Press OK to confirm the selection.

The chosen items are listed.

6. Press View Details to get more information.

Send data from the data log

Data is sent from the internal data log as an XML (Extensible Markup

Language) file or as a CSV (Comma Separated Value) file, to a directory

with the name DataLog on a USB mass storage device or a network

drive. The file can then be processed using a spreadsheet program. The

file name has the format: DLYear-Month-

Day_Hour_Minute_Second.csv or DLYear-Month-

Day_Hour_Minute_Second.xml.

1. Plug the USB storage device into the USB type A port on the

DR 3900, or connect the DR 3900 to a network drive.

2. Press Recall Data from the Main Menu.

3. Select the data category to be transferred, e.g. Data Log.

A list of the selected measurement data is displayed.

4. Press Options and then the PC&Printer icon.

English 17

5. Select the data to be sent.

The following options are available:

• Single point: only this selected reading will be sent

• Filtered data: only readings that correspond to the set filters

will be sent

• All data: all data in the selected data category will be sent.

6. Press OK to confirm.

Note: The number in parentheses is the total number of data sets

assigned to this selection.

Stored Programs

1. Press Stored Programs in the Main Menu to view an alphabetical

list of stored programs with program numbers.

The "Stored Programs" list will appear.

2. Highlight the required test.

Hinweis: Select the program by name or scroll through the list

using the arrow keys. Highlight the program or press Select by No.

to search for a specific program number. Press OK to confirm.

3. Press Start to run the program. The respective measurement

window is displayed.

Hinweis: All corresponding data (wavelength, factors and

constants) is already preset.

4. Follow the instructions for chemical procedures in the relevant

procedures manual. Further information are available on the

website of the manufacturer.

Hinweis: To display the procedural instructions in the display, press

the info icon. Not all programs have this option.

English 18

Complete a barcode test

1. Insert the light shield into cell compartment (2).

2. Prepare the barcode test according to the process specification,

and insert the cell in cell compartment (1).

• When a coded cell is placed in cell compartment (1) (Figure 3,

page 10), the corresponding reading program is automatically

activated in the Main Menu.

• Otherwise, press Barcode Programs in the Main Menu and

insert a zero cell (depending on process specification) into cell

compartment (1).

The reading is started automatically and the results are displayed.

To evaluate other cell tests and other parameters, insert the prepared

cell into the cell compartment and read off the result.

Note: The control bar displayed on the right of the screen shows the

relationship of the reading result to the measuring range. The black bar

shows the measured result independently of any dilution factor that was

entered.

Select the chemical evaluation form

The chemical form of the test result of a number of parameters can be

selected individually.

1. In the result display, press the unit (e. g. mg/L) or the chemical

representation of the evaluation form (e. g. PO

4

3–

–P).

A list of available evaluation forms appears.

2. Select the required form from the list. Press OK to confirm.

Another way of changing the standard setting is:

English 19

1. In the result display, press Options>More>Chemical Form.

A list of available evaluation forms appear.

2. Select the required chemical form and press OK to confirm.

Hinweis: The selected chemical form is displayed, but does not

become the default. To change the default, refer to section Change

of the default setting of the chemical form.

Change of the default setting of the chemical form

1. Insert the zero cell or sample cell (corresponding to the process

specification) into the cell compartment.

2. In the result display, press Options>More>Chemical Form.

3. A list of available evaluation forms appear. Select the new default

setting.

4. Press Save as Default.

The current result and all further readings will be displayed in the new

chemical form.

Troubleshooting

Error displayed Definition Resolution

Attention!

Please insert the light

shield.

Readings with barcode

cuvettes generally

require the light shield.

Insert the light shield.

Press OK.

Barcode label not read Barcode faulty

Reinsert the cell.

If the barcode is not

recognised, contact the

manufacturer or his

representative.

An error occurred

when uploading the

instrument data.

Start the procedure again

or contact the manufac-

turer or his representa-

tive.

An error occurred when

reading from the USB

memory stick.

Start the procedure again

or contact the

manufacturer or his

representative.

An error occurred when

writing to the USB

memory stick.

Start the procedure again

or contact the

manufacturer or his

representative.

Please check on the

current update file.

Error during update.

Check the USB memory

stick.

Please contact

Customer Services.

Error during update.

Please check network

configuration.

Please check the

connection.

Please close the cover. Close the cover.

English 20

Please insert the USB

memory stick.

Insert a USB memory

stick into a USB A port on

the instrument.

Please check the

connection and contact

the administrator.

Network setup or FTP

error

Blank value correction

not possible!

Blank value correction

not possible with

LCW919.

File for instrument

update missing.

Error during update.

Check the USB memory

stick.

File for instrument

update is faulty.

Error during update.

Save the update file

again and repeat the

procedure.

It’s recommended to

execute a Full System

Check

Check of the air values

failed

Switch the instrument of

and then back on again.

If the system check is not

successful, contact the

manufacturer or his

representative.

Entry invalid! Password incorrect

Forgotten your

password?

Contact the

manufacturer or his

representative.

Absorbance > 3.5!

The measured

absorbance exceeds 3.5

Dilute sample and

measure again

Fault

Barcode check

number?

Please update program

data!

Deviation to the stored

data

Data updating

Error when calling up

the local IP address.

Network setup: DHCP

client has no connection

to the DHCP server

Enter the IP address

again.

Error displayed Definition Resolution

Error during default

gateway setup.

Network setup: default

gateway cannot be set

for fixed IP address

Try to create the

connection again.

Error during network

drive setup!

Error during network

setup

Check the settings.

Error during subnet

mask setup.

Network setup: Subnet

mask cannot be set for

fixed IP address

Enter the subnet mask

again.

Error copying from USB

memory stick.

Error during update

Start the procedure again

or contact the

manufacturer or his

representative.

Error in FTP

connection.

FTP error

Make sure that the

instrument is connected

to the network.

Fault

Program not

accessible.

Please update program

data!

Barcode test not present Data updating

Fault

Clean cuvette!

The cuvette is soiled or

there are undissolved

particles in the cuvette

Clean the cuvette; allow

the particles to settle

Fault

Test program stopped!

Please check lamp

Close the lid.

Error [xx]

Test program stops when

the instrument is started

Check the lamp and

replace it if necessary.

Close lid.

Press Start Again.

Fault

Test program stopped!

Please remove the

cuvette

Close the lid.

Test program stops when

the instrument is started

Remove the cuvette/

sample cell from the cell

compartment.

Press OK.

Error displayed Definition Resolution

La page charge ...

Hach DR 3900 Basic User Manual

Hach DR 3900 Basic User Manual

dans d''autres langues

Documents connexes

Autres documents