CHAUVIN ARNOUX C.A 5220 G Manuel utilisateur

Marque: CHAUVIN ARNOUX

Modèle: C.A 5220 G

Catégorie: Multimètres

Taper: Manuel utilisateur

Ce manuel convient également à

C.A 5210 G

■■

■ MULTIMETRES

■■

■ MULTIMETERS

■■

■ MULTIMETROS

■■

■ MULTIMETERS

■■

■ MULTIMETRI

FRANCAIS

Mode d'emploi

ENGLISH User's manual

ESPANOL

Manual de Empleo

DEUTSCH Bedienungsanleitung

ITALIANO Libretto d'Istruzioni

C.A 5210 G

C.A 5220 G

CARACTÉRISTIQUES GÉNÉRALES

Dimensions et masse

■ 64 x 177 x 42 mm ■ 350 g

Alimentation

■ Deux piles 1,5 V (type R6)

■ Autonomie : 300 h avec piles R6

600 h avec pile alcaline LR 6

18000 mesures de 1 minute avec pile R6

■ Indication d'usure des piles :

NB : La tension des piles est indiquée approximativement sur la fonction

diodes en circuit ouvert.

■ Arrêt automatique au bout de 30 minutes

NB : Remise en marche en passant par la position OFF ou en

appuyant sur la touche .

Buzzer

■ Bip sonore continu pour le test de continuité

■ Bip sonore discontinu à chaque action sur le commutateur et les touches, et

pour l'indication de dépassement

NB : Pas de bip sonore sur la touche et sur le commutateur entre V

et Velec

Conditions climatiques

■ Température : - utilisation : 0°C à +50°C

- stockage : -20°C à +70°C

■ Humidité relative : - utilisation : ≤ 80 % HR

- stockage : ≤ 90 % HR (jusqu'à 45°C)

Conformité aux normes

■ Double isolation (selon CEI 1010-1 - Catégorie

d'installation III - degré de pollution 2)

■ Etancheité : IP 50 (selon CEI 529)

■ Autoextinguibilité : V1 et V2 (selon UL 94)

■ Chute libre : 1 m (selon CEI 1010)

■ Chocs : 0,5 J (selon CEI 68.2.27)

■ Vibrations : 0,75 mm (Selon CEI 68.2.6)

■ Décharge électrostatique : 4 kV classe 2 (selon CEI 801-2)

■ Champs rayonnés : 3 V/m (selon CEI 801-3)

■ Transitoires rapides : 2 kV (selon CEI 801-4)

■ Chocs électriques : 3 kV (selon CEI 801-5)

Sauf dérogation contraire, nos instruments sont garantis contre tout défaut de

fabrication ou de matière. Ils ne comportent pas la spécification dite de sécurité.

Notre garantie, qui ne saurait en aucun cas excéder le montant du prix facturé,

ne va pas au-delà de la remise en état de notre matériel défectueux, rendu franco

à nos ateliers. Elle s’entend pour une utilisation normale de nos appareils, et ne

s’applique pas aux détériorations ou destructions provoquées, notamment par

erreur de montage, accident mécanique, défaut d’entretien, utilisation défectueu-

se, surcharge ou surtension, intervention de calibration faite par des tiers.

Notre responsabilité étant strictement limitée au remplacement pur et simple des

pièces défectueuses de nos appareils, l’acquéreur renonce expressément à

rechercher notre responsabilité pour dommages ou pertes causés directement

ou indirectement.

Notre garantie s’exerce, sauf stipulation expresse, pendant trois ans après

la date de mise à disposition du matériel. La réparation, la modification ou le

remplacement d’une pièce pendant la période de garantie ne saurait avoir pour

effet de prolonger cette garantie.

POUR COMMANDER

Utiliser les désignations et références ci-dessous.

Réf

C.A 5210 G (livré avec gaine n°12)

................................................. P01.1967.11B

C.A 5220 G (livré avec gaine n°12)

................................................. P01.1967.12B

Livrés avec un jeu de 2 cordons à pointe de touche,

2 piles 1,5 V et ce mode d'emploi

Accessoires et rechanges

■ Gaine antichoc n°12

..................................................................... P01.2980.15

■ Minipince n°5 (jusqu'à 100 A ~)

..................................................P01.1050.05

■ Pince Y 500 (jusqu'à 500 A ~)

.................................................... P01.1200.05

■ Pince C 31 (jusqu'à 1000 A ~)

.................................................... P01.1200.34

■ Pince PAC 500 B (jusqu'à 600 A

ou ~) ............................... P01.1200.38

■ Pince PAC 1000 B (jusqu'à 1000 A ou 700 A ~)

.................... P01.1200.32

■ Sonde haute tension 30 kV et 20 kV ~

..................................... P03.1002.34

■ Cellule photoélectrique 651 A (0-12000 lux)

............................ P03.1008.16

■ Sonde de température ST2

(-50°C à +1000°C selon capteur)

.............................................. P03.6525.01

■ Sonde tachymétrique TACHY 6

................................................. P03.1973.01

(jusqu'à 60000 tours/minute)

■ Cordon adaptateur n°214 (intensité alternatives)

................... P03.2955.04

■ Jeu de 2 cordons n°181 A/B

....................................................... P03.1008.19

■ Jeu de 10 fusibles 0,4 A HPC (6,3 x 32 mm)

.......................... P01.2970.20

■ Jeu de 10 fusibles 12 A HPC (10,3 x 38 mm)

......................... P01.2970.21

GARANTIE

English

Thank you for your confidence in choosing

a CHAUVIN ARNOUX instrument.

Before using your multimeter and in order to get the best use from it :

■ READ carefully the advice and recommendations in this

User’s manual.

■ RESPECT the safety precautions.

■ International electric symbol :

Warning ! Consult the User’s manual before using the

instrument

Warning, if replacing the fuses, it is essential to respect the value and

the type otherwise there is a risk of damage to the instrument and

invalidation of the warranty.

■ Fuse 0.4A HBC - 600V min (6.3 x 32mm)

■ Fuse 12A HBC - 600V min (10.3 x 38mm)

Fuses in the C.A 5220 G

SUMMARY

Page

■ Presentation ............................................................................................. 18

■ Safety precautions ................................................................................ 18

■ Replacing the batteries and fuses .................................................. 19

■ Description ............................................................................................... 19

■ DC and AC voltages [V] ..................................................................... 21

■ AC voltages - low impedance [V elec] ......................................... 21

■ Continuity sound test [ ] .............................................................. 23

■ Resistances [Ω] ..................................................................................... 23

■ Diode tests [ ] ................................................................................ 24

■ Capacitances [ ] .............................................................................. 25

■ Frequencies [ Hz] .................................................................................. 26

■ DC and AC currents (A and mA) .................................................... 27

■ Measurements with accessories .................................................... 29

■ General specifications ......................................................................... 30

■ Accessories and spare parts (To order) ..................................... 31

■ Warranty ................................................................................................... 31

■ Descriptive drawings .........................................................................80/81

PRESENTATION

The C.A 5210 G and C.A 5220 G are designed for the daily needs of professionals

in electricity.

They have a dual display :

- digital 4000 counts

- 40 segment bargraph

The range selection is automatic, with the possibility of manual selection on the

C.A 5220 G. It switches Off automatically if no control or function button is pressed

for 30 minutes.

For the safety of the user, these multimeters meet the most demanding

international standards; firstly : double insulation (in accordance with

IEC 1010-1-III-2).

Model C.A 5220 G, which is more complete, in particular allows the direct

measurement of current and frequency measurement (see Description chapter).

SAFETY PRECAUTIONS

■ Never use on DC or AC networks higher than 600V rms.

■ Never open the case of the multimeter before having disconnected it from all

electric sources.

■ Never connect to the circuit to be measured if the case of the instrument is not

correctly closed.

■ Before any measurement, check the correct position of the leads and of the

selector switch.

■ Never make resistance measurements on a live circuit.

■ For the C.A 5220 G multimeter, when making current measurements, always

switch Off the power supply to the circuit before connecting or disconnecting

the instrument to the circuit.

REPLACING THE BATTERIES

AND THE FUSES

The 1.5V batteries, as well as the 0.4 A HBC and 12 A HBC fuses for model

C.A 5220 G, are accessible at the back of the instrument.

Remove the lower half of the case after removing the three screws.

Replace the faulty elements, in accordance with :

- polarity for the batteries

-the value and the type of fuses

■ Fuse 0.4 A HBC - 600V min (6.3 x 32 mm)

■ Fuse 12 A HBC - 600V min (10.3 x 38 mm)

DESCRIPTION

(See p.80 and 81)

1 - LIQUID CRYSTAL DISPLAY

■ 4000 measuring counts (digit height 10mm)

Rate : 2 measurements/sec

■ 40 segment bargraph

Rate : 20 measurements/sec

NB : the bargraph is not operational for frequency and capacitance

measurements

■ Automatic display of all the symbols for controls, ranges and functions

■ , low battery indication

■ Overload indication :

- the 4 on the left flashes

- arrow at the end of the bargraph

2 - CONTROL BUTTONS

/ ~ and

Ω Ω

Ω /

To change from AC (~) to DC (

) and the reverse, on voltage and current :

To change from continuity ( ) to the measurement of resistance (Ω) and back,

on ohmmeter function.

NB :Automatic selection of ~ and when it is switched On.

HOLD

To memorise the last measurement (digital and bargraph).

MIN.MAX (C.A 5220 G only)

To successively display the min or max values.

The C.A 5220 G then changes to manual range selection.

HOLD is also displayed. Min. acquisition time 500ms.

NB : Press the HOLD button to read the min value before disconnecting

the instrument

RANGE (C.A 5220 G only)

Range selection : To change from automatic mode to manual mode. A prolonged

press on this button allows you to exit the manual mode.

The automatic mode is selected when the instrument is switched On.

NB :This button also selects the sensitivity for the frequencemeter function (Hz).

(C.A 5220 G only)

To switch On and Off the lighting of the display.

NB : Auto Off after 5 minutes.

3 - FUNCTION SELECTOR SWITCH

OFF Off position

V DC and AC voltages up to 600 V, with high impedance : 10 MΩ

V elec AC voltages up to 600 V, with low impedance : 270 kΩ

NB : Also available on DC voltage.

Adp (C.A 5210 G only)

Adaptor input : 400mV DC ; to receive themeasurement accessories with mV DC

output. The value is displayed without indication of the mV unit for ease of reading

(in °C, in lux, ...)

Hz (C.A 5220 G only)

Frequencies of voltages, up to 200kHz

ΩΩ

Ω

Continuity sound test for a resistance ≤ 40 Ω, and resistance measurements up

to 40 MΩ

The continuity test is selected automatically when the instrument is swiched On.

Diode test. Measures the voltage of the junction in forward direction.

Capacitances up to 40µF

A (C.A 5220 G only)

10A DC and AC current ranges (via the 10A terminal)

mA (C.A 5220 G only)

Current ranges up to 400mA DC and AC (via the + terminal)

4 - TERMINALS

4mm diameter safety terminals

■ COM : common, terminal receiving the black lead

■ + : terminal receiving the red lead

■ 10 A (C.A 5220 G only) : terminal receiving the red lead for the 10A DC and

AC ranges

V DC

400 mV 4 V 40 V 400 V

Digital

resolution

0.1 mV 1 mV 10 mV 100 mV 1 V

Bargraph

resolution

10 mV 100 mV 1 V 10 V 100 V

V DC

Impedance

V elec

Impedance

Accuracy ± 1 % reading ± 1 count

Permitted

overload

600 V rms and 900 V peak

■ Connect the leads to the multimeter and connect it in parallel to the circuit to

be tested.

■ Place the selector switch on voltmeter (V) function (high impedance).

The instrument is in AC mode. Press the DC/AC button to select DC and vice

versa.

■ Automatic range selection : read the measured value.

■ Memorise the value, if necessary, by pressing the HOLD button.

C.A 5220 G only

If necessary, press the following buttons :

■ RANGE to select the ranges manually

■ MIN.MAX to read the min or max values

■ to switch on the backlight of the display

DC and AC VOLTAGES

VOLTAGES WITH

LOW IMPEDANCE: V elec

Identical procedure (as above) except for positioning the selector switch on

V elec.

DC VOLTAGES

270 kΩ

10 MΩ

(1) 4000 count display limited to 600V

600 V

(1)

AC voltages

(1) C.A 5220 G only. Press the RANGE button.

Min measurement : 40mV

(2) 4000 count display limited to 600V

(3) Use on frequency : 40Hz to 500Hz, except the

400mV range from 40Hz to 100Hz.

V AC

4 V 40 V 400 V

Digital

resolution

0.1 mV 1 mV 10 mV 100 mV 1 V

Bargraph

resolution

10 mV 100 mV 1 V 10 V 100 V

V AC

impedance

V elec

impedance

± 1.5 % reading ± 1 count

Permitted

overload

600 V rms and 900 V peak

270 kΩ

600 V

(2)

400 mV

(1)

10 MΩ

Accuracy

(3)

±5%R

Never test a resistance on a live circuit

■ Connect the leads to the multimeter and to the circuit or the component to be

tested.

■ Place the selector switch on the ohmmeter function Ω

Press the Ω/ button to change from continuity sound test to resistance

measurement and vice versa.

■ Automatic range selection: read the measured value

■ Memorise the value, if necessary, by pressing the HOLD button.

C.A 5220 G only

If necessary, press the following buttons:

■ RANGE to select the range manually

■ MIN.MAX to read the min or max values

■ to light the display

CONTINUITY AND RESISTANCES

Digital

resolution

Bargraph

resolution

Accuracy

± 1.5 %

R ± 8

counts

± 1.5 % R ± 3 counts

± 3 % R

± 5

counts

Voltage

on open

circuit

Protection 500 V rms and 750 V peak

ΩΩ

Ω 400 Ω 4 kΩ 40 kΩ 400 kΩ 4 MΩ 40 MΩ

0.1 Ω 1 Ω 10 Ω 100 Ω 1 kΩ 10 kΩ

10 Ω 100 Ω 1 kΩ 10 kΩ 100 kΩ 1 MΩ

≤ 0.5 V

CONTINUITY SOUND TEST

On the 400 Ω range, continuous beep for a resistance R ≤ 40 Ω

RESISTANCES

DIODES

Never make a diode test on a live circuit

■ Connect the leads to the multimeter and to the terminals of the component

to be tested.

■ Place the selector switch on the diode function :

-in forward direction the display gives the value of the junction in volts

(resolution 1mV)

- accuracy : ± 2 % R ± 15 mV

- open circuit voltage : ≥ 3 V

-short circuit current : 0.8mA

- in reverse direction the display indicates the open circuit voltage,

around 3V.

■ Memorise the value if necessary, by pressing the HOLD button.

■ With this function it is thus possible to test standard diodes, l.e.d’s or any other

semiconductor which has a junction that corresponds to a direct voltage of

less than 3V.

■ Protection : idem resistances

CAPACITANCES

■ Never measure a capacitance on a live circuit.

■ Always respect the polarity of electrolytic condensors.

This type of condenser may be sensitive to temperature,

so avoid touching it during measurement.

■ Connect the leads to the multimeter and to the terminals of the condenser.

■ Place the selector switch on the capacitance meter function .

■ Automatic range selection : read the measured value

NB : The bargraph is not operational during capacitance measurement.

■ Memorise the value, if necessary, by pressing the HOLD button.

C.A 5220 G only

If necessary, press the following buttons :

■ RANGE to select the ranges manually

■ to light the display

■ MIN.MAX to read the min or max values

CAPACITANCES

(1) Min measurement : 400pF.

4 nF

(1)

40 nF 400 nF 4 µF 40 µF

Resolution1 pF 10 pF 100 pF 1 nF 10 nF

Precision

Protection 500 V rms and 750 V peack

± 3 % R ± 3 % R ± 5 % reading ± 15 % R

± 400 ± 25 ± 10 counts ± 10

counts counts counts

■ Connect the leads to the multimeter and in parallel to the circuit to be tested.

■ Place the selector switch on the Hz voltage frequency function

■ Automatic range selection : read the measured value

NB : The bargraph is non-operational on frequency measurement

■ If necessary, press the following buttons

- MIN.MAX to read the max or min value

-to light the display

FREQUENCIES

(C.A 5220 G only)

100 Hz 1 kHz 10 kHz 100 kHz 200 kHz

Resolution 0.01 Hz 0.1 Hz 1 Hz 10 Hz 100 Hz

Accuracy ± 0.1 % reading ± 2 counts

Permitted

overload

600 V rms and 900 V peak

Operating range

4 V to 600 V

(1) The RANGE button on this function selects the trigger level :

10 mV, 100 mV or 1V (10 mV is selected when the instrument is

switched on).

FREQUENCIES (extension to 10 000 counts)

Always switch Off the circuit to be tested before connecting

the multimeter to the circuit

■ Warning : connect the leads to the multimeter and connect in series to the

circuit

-the red lead to the + terminal up to 400mA

-the red lead to the 10A terminal , from 400mA to 10A

■ Place the selector switch to the A or mA ammeter function.

Press the DC/AC button to select DC or AC.

■ Switch On the circuit to be tested so that it is live

■ Automatic range selection : read the measured value

■ If necessary, press the following buttons

- RANGE to manually select the ranges

-MIN.MAX to read the min or max values

- to light the display

DC and AC CURRENTS

(C.A 5220 G only)

A DC

40 mA 400 mA 10 A (1)

Voltage (2)

drop

600 mV 4,5 V 600 mV

Digital

resolution

10 µA 100 µA 10 mA

Bargraph

resolution

1 mA 10 mA 1 A

Accuracy

± 1.5 % reading ± 1 count

± 1.5 % R

± 2 counts

Protection (3)

Fuse 0.4 A HBC Fuse 12 A HBC

DC CURRENTS

A AC

40 mA 400 mA

Voltage (2)

drop

600 mV 4,5 V 600 mV

Digital

resolution

10 µA 100 µA 10 mA

Bargraph

resolution

1 mA 10 mA 1 A

Accuracy (4)

± 1.5 % reading ± 2 counts

± 2 % R

± 2 counts

Protection (3)

Fuse 0.4 A HBC Fuse 12 A HBC

(1) 4000 count display limited to 10 A Between 5A and 10A, to avoid

overheating, limit the operating time to 10 minutes

(2) Voltage drop at the terminals for 40mA, 400mA, 10A

(3) Permitted overloads :

600 mA for 30 seconds for the 400 mA range

15 A for 30 seconds for the 10 A range

(4) Use on frequency : 40Hz to 500Hz

AC CURRENTS

10 A (1)

Different measurement accessories enlarge the field of application or add new

functions to your multimeter.

(See «To order» for the list of accessories and their reference. Documentation

on request)

HIGH CURRENT MEASUREMENTS

■■

■

Miniclamps and current clamps, series C, D and Y, simplify the measurement

of AC currents.

Measurements are made rapidly and in complete safety, without the need to

switch Off the circuit.

According to the clamp used and the ranges concerned, you may measure

100A, 500A, 1000A and up to 3000A AC.

There are two types of clamps, with current output and with voltage output.

-Example of current output :

Output signal : 1mA AC/1 A AC

Use the mA AC ranges

For a current of 100A AC, reading 100mA AC

- Example of voltage output :

Output signal : 1mV AC/1 A AC

Use the mV AC ranges (C.A 5220 G only)

For a current of 100 A AC, reading 100mV AC

■■

■ Hall effect clamps, series E and PAC, have the

same advantages but measure both DC and AC

currents

- output signal : 1mV DC/1 A DC and 1mV AC/1 A AC

MEASUREMENT OF HIGH DC VOLTAGES

The HT probe enables the measurement of high voltages up to 30kV DC and

20 kV AC

- output signal : 1V DC/1kV DC or 1V AC/1kV AC

LIGHTING MEASUREMENTS

The 651 A cell transforms your multimeter into a luxmeter; measurements up to

12000 lux (with 1/10 screen)

- output signal : 1mV DC/10 lux

TEMPERATURE MEASUREMENTS

The ST2 probe transforms your multimeter into a thermometer; it can be used in

many applications with 8 specialised sensors (type K); measurements up to

1000°C according to the sensor chosen.

- output signal : 1mV DC/1°C

MEASUREMENTS OF ROTATIONAL SPEED

The TACHY 6 probe transforms your multimeter into a tachometer; measurements

up to 6000 and 60000 rpm

- output signal : 1mV DC/1 rpm

1mV DC/10 rpm

MEASUREMENTS WITH ACCESSORIES

CHAUVIN ARNOUX C.A 5220 G Manuel utilisateur

Marque: CHAUVIN ARNOUX

Modèle: C.A 5220 G

Catégorie: Multimètres

Taper: Manuel utilisateur

Ce manuel convient également à

C.A 5210 G

Télécharger le PDF

rapport

dans d''autres langues

English: CHAUVIN ARNOUX C.A 5220 G User manual

CHAUVIN ARNOUX C.A 5220 G Manuel utilisateur

Ce manuel convient également à

CHAUVIN ARNOUX C.A 5220 G Manuel utilisateur

dans d''autres langues

Autres documents