Motorola H790 - Headset - Monaural Guide de démarrage rapide

MOTOROLA and the Stylized M Logo are registered in the US Patent &

Trademark Ofﬁce. All other product or service names are the property of

their respective owners. The Bluetooth trademark and logos are owned by

the Bluetooth SIG, Inc. and any use of such marks by Motorola, Inc. is under

68014301015

motorola.com

MOTOROLA and the Stylized M Logo are registered in the US Patent &

Trademark Ofﬁce. All other product or service names are the property of

their respective owners. The Bluetooth trademark and logos are owned by

the Bluetooth SIG, Inc. and any use of such marks by Motorola, Inc. is under

68014301015

motorola H790

Quick Start Guide

1

Figure 1

7

1

6

2

4

8

3

5

2

Figure 2

Figure 3

 



English

3

Before you begin

See ﬁgure 1 on page 1.

Take a moment to familiarize yourself with your new H790 Headset.

1 Charging port

2 Call button

3 Indicator light

4 Power switch

5 Microphone

6 Volume buttons

7 Earhook

8 Ear speaker

IMPORTANT

Depending on the country in which you purchased your H790 headset,

English language Voice Prompts may be defaulted ON or OFF. If the Voice

Prompts are ON, you will hear a voice when turning on the headset and

when using it.

If you wish to change the voice prompt default setting:

With the headset turned on, press and hold either Volume button and Call

button until you hear “voice prompts on” or “voice prompts off”.

Note: Voice prompts are supported in English only.

English

4

Wearing your headset

See ﬁgures 2 on page 2.

To get the best headset performance, try out all the supplied ear cushions

to get a good ﬁt.

Your headset comes ready for the right ear. You can change it for wear on

the left ear.

For optimal audio performance and comfort, be sure to position the ear

cushion into your ear canal and point the headset microphone towards

your mouth.

Charging your headset

See ﬁgure 3 on page 2.

Charge your headset before using it.

The indicator light is red or yellow while the battery is charging. When the

battery is fully charged, the indicator light turns green.

Note: Headset is not functional while charging.

Turning headset on & off

Slide the Power switch to the ON position (no red is shown under the switch).

The indicator light ﬂashes blue three times, then ﬂashes in blue and purple (if

connected with a device) or is steadily blue (if ready to be paired).

Slide the Power switch to the OFF position (red is shown under switch). The

indicator light ﬂashes three times then turns off.

English

5

Pairing & connecting your headset

Initial pairing & connection

Once charged, let’s get your headset paired and connected to your Bluetooth

phone(s).

1. Turn off any Bluetooth devices previously paired with your headset.

2. Turn on the Bluetooth feature on your phone.

3. Put headset on your ear and turn it on. The indicator light becomes

steadily lit in blue.

4. With voice prompts ON:

• You will hear“ready to pair”.

• Follow voice prompts to connect your phone to your headset.

• When prompted for the passkey, enter 0000.

• When your headset successfully pairs with your phone, you hear “pairing

complete”. When connected, you hear “phone 1 connected” and see the

indicator light rapidly ﬂash in blue and purple.

• OR

• With voice prompts OFF:

• Go to the Bluetooth menu on your phone and look for devices.

• Select Motorola H790.

• When your headset successfully pairs with your phone, the indicator light

ﬂashes purple and blue and you hear two ascending tones.

English

6

Pairing & connection to 2 devices (optional)

1. Turn off ﬁrst phone and any other Bluetooth devices previously paired

with your headset.

2. Turn your headset off

3. Turn on the Bluetooth feature on your phone.

4. Put headset on your ear and turn it on. The indicator light becomes

steadily lit in blue.

5. With voice prompts ON:

• You will hear“ready to pair”.

• Follow voice prompts to connect your phone to your headset.

• When your headset successfully pairs with your phone, you hear “pairing

complete”. When connected, you hear “phone 1 connected” and see the

indicator light rapidly ﬂash in blue and purple.

• To connect to both phones, simply turn on the ﬁrst phone while the second

phone is connected. When you hear “phone 2 connected”, your headset

is connected to both phones.

• OR

• With voice prompts OFF:

• Go to the Bluetooth menu on your phone and look for devices.

• Select Motorola H790.

• To connect to both phones, simply turn on the ﬁrst phone while the second

phone is connected. When you hear 2 ascending tones, your headset is

connected to both phones.

Note: The last paired phone (your second phone) is now your primary phone

(or “phone 1”) for voice dial functionality regardless of voice prompts being

activated or not.

English

7

Test your connection

Place the headset on your ear and make a call from the phone(s). If your

phone(s) and headset are successfully connected, you hear ringing on the

headset.

For daily use, make sure your headset is turned on, and your phone’s

Bluetooth feature is on. Your headset and phone will connect automatically!

Using your headset

Function Action

Answer a call Press the Call button

Reject a call Press and hold a Volume button until you hear

an audio tone

Make a voice dial call Press the Call button and you hear an audio

tone

Redial last call Press and hold the Call button until you hear an

audio tone

Mute or unmute a call With voice prompts ON: Press and hold both

Volume buttons until you hear “mute on” or

“mute off”

With voice prompts OFF: Press and hold both

Volume buttons until you hear 2 ascending

tones (for mute ON) and 2 descending tones

(for mute OFF)

End a call Press the Call button

Answer a second Press the Call button

incoming call

Reject second Press and hold a Volume button until you hear

incoming call a tone

English

8

Note: Your headset supports both Hands-free and Headset Profiles.

Accessing call functions depends upon which proﬁle your phone supports.

See the instructions that came with your phone. See your phone’s user’s

guide for more information.

Note: Some call features are phone/network dependent.

Tip: When connected to two phones, voice prompts help manage call

functions such as voice dial, redial, and end call. Follow the voice prompts to

execute a function on the desired phone.

Status Indicators

Battery check

Press and hold both Volume buttons while not on a call.

Indicator light Voice prompt Talk time

Red “battery level is low” Less than 1.5 hours

Yellow “battery level is medium” Between 1.5 to 3.5 hours

Green “battery level is high” More than 3.5 hours

To save battery power, turn off the headset when you don’t use it for an

extended time.

Charging status (with charger plugged in)

Indicator light Headset status

Red Charging (battery level less than 50% charge)

Yellow Charging (battery level more than 50% charge)

Green Charging complete

English

9

Operating status (with no charger plugged in)

Indicator light Headset status

Off Power off

3 blue ﬂashes Powering on/off

Steady blue Pairing/connect mode

Rapid blue/purple ﬂashes Connection successful

Quick blue ﬂash Incoming/outgoing call on phone 1

Quick purple ﬂash Incoming/outgoing call on phone 2

Slow blue pulse Connected (on a call)

Slow blue ﬂash Standby (connected to one phone)

Slow green ﬂash Standby (connected to two phones)

Slow red ﬂash Idle (not connected to a phone)

Slow purple pulse Connected call muted

Steady red Attempting to connect

Quick red ﬂash Low battery

Note: After 1 minute on a call or 20 minutes of inactivity, the light stops

ﬂashing to conserve power, but the headset remains on.

Tips and tricks

Restore to factory settings

Caution: This action erases all pairing information stored in your headset.

To restore your headset to original factory settings, with the headset turned

on, press and hold both Volume buttons and Call button for 10 seconds until

the indicator light is steady blue.

English

10

Troubleshooting

My headset will not enter pairing mode

Make sure that any devices previously paired with the headset are turned

off. If the indicator light is ﬂashing in blue, ﬁrst turn off the other device, then

turn the headset off and on. The indicator light becomes steadily lit in blue

and, with voice prompts ON, you hear “ready to pair”.

My phone doesn’t ﬁnd my headset when searching

Make sure the indicator light on your headset is steadily lit in blue when

your phone is searching for devices. If not, press and hold the Call button

and both Volume buttons until you hear “ready to pair” and see the indicator

light steadily lit in blue.

My headset will not pair with my phone

If the indicator light is not steadily lit in blue when your phone is searching

for your headset, you can reset the headset by pressing and holding the Call

button and both Volume buttons until the indicator light is steadily lit in blue.

Then follow pair & connect instructions.

My headset connected before, but now it’s not working

Make sure the indicator light on your headset is steadily lit in blue when

your phone is searching for devices. If not, press and hold the Call and both

Volume buttons until you see the indicator light steadily lit in blue and, with

voice prompts ON, you hear“ready to pair”.

If you have any additional questions, please call your hotline number

(0870-9010-555) or visit us at www.hellomoto.com.

English

11

European Union Directives Conformance Statement

Hereby, Motorola Inc., declares that this H790 is in compliance

with the essential requirements and other relevant provisions of

Directive 1999/5/EC.

You can view your product’s Declaration of Conformity (DoC) to Directive

1999/5/EC (the R&TTE Directive) at www.motorola.com/rtte.

Caring for the Environment by Recycling

When you see this symbol on a Motorola product, do not dispose of

the product with household waste.

Recycling Mobile Phones and Accessories

Do not dispose of mobile phones or electrical accessories, such as chargers

or headsets, with your household waste. In some countries or regions,

collection systems are set up to handle electrical and electronic waste

items. Contact your regional authorities for more details. If collection systems

aren’t available, return unwanted mobile phones or electrical accessories to

any Motorola Approved Service Centre in your region.

FCC Notice to Users

FCC Notice The following statement applies to all products that have

received FCC approval. Applicable products bear the FCC logo, and/or an

FCC ID in the format FCC-ID:xxxxxx on the product label.

Motorola has not approved any changes or modiﬁcations to this device by

the user. Any changes or modiﬁcations could void the user’s authority to

operate the equipment. See 47 CFR Sec. 15.21.

This device complies with part 15 of the FCC Rules. Operation is subject

to the following two conditions: (1) This device may not cause harmful

interference, and (2) this device must accept any interference received,

including interference that may cause undesired operation. See 47 CFR Sec.

15.19(3).

English

12

This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to part 15 of the FCC Rules. These limits are

designed to provide reasonable protection against harmful interference in

a residential installation. This equipment generates, uses and can radiate

radio frequency energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or

more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment to an outlet on a circuit different from that to which

the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Approved Accessories

Use of accessories not approved by Motorola, including but not limited to

batteries, antennas, and convertible covers, may cause your mobile device

to exceed RF energy exposure guidelines and may void your mobile device’s

warranty.

Motorola recommends that you always use Motorola-branded chargers.

Motorola devices are designed to work with Motorola chargers.

For approved Motorola accessories, visit our Web site at: www.motorola.com

Use & safety for battery-powered accessories

Your battery is designed to last the life of the product. It should only be

removed by a recycling facility. ANY ATTEMPT TO REMOVE OR REPLACE

YOUR BATTERY WILL DAMAGE THE PRODUCT.

• Battery life may temporarily shorten in low-temperature conditions (-10°C

for storage/use below 0°C for recharge) or permanently reduce in high

temperature conditions (above 60°C for storage/use or above 45°C for

recharge).

• Do not let your mobile device get wet.

• Do not store your accessory in a parked car or direct sunlight.

WARNING: MAY EXPLODE IF DISPOSED OF IN FIRE.

Driving Precautions

Check and obey the laws and regulations on the use of mobile devices in the

area where you drive. The use of wireless devices and their accessories in

your area may be prohibited or restricted. The use of wireless phones while

driving may cause distraction. Discontinue a call if you can’t concentrate on

driving. When using your mobile device while driving, please:

• Give full attention to driving and to the road.

• Use your hands-free solution to perform hands-free calls.

• Pull off the road and park before making or answering a call if driving

conditions so require.

Caution about high volume usage

Warning: Exposure to loud noise from any source for extended periods of

time may temporarily or permanently affect your hearing. The louder the

volume sound level, the less time is required before your hearing could be

affected. Hearing damage from loud noise is sometimes undetectable at ﬁrst

and can have a cumulative effect. To protect your hearing:

• Start your volume control at a low setting and use as low a volume as

possible.

• Limit the amount of time you use headsets or headphones at high volume.

• Where possible, use your headset in a quiet environment with low

background noise.

• Avoid turning up the volume to block out noisy surrounding.

• Turn the volume down if you can’t hear people speaking near you.

If you experience hearing discomfort, including the sensation of pressure or

fullness in your ears, ringing in your ears, or mufﬂed speech, you should stop

listening to the device through your headset or headphones and have your

hearing checked by your doctor.

English

13

• Do not let your mobile device get wet.

• Do not store your accessory in a parked car or direct sunlight.

WARNING: MAY EXPLODE IF DISPOSED OF IN FIRE.

Driving Precautions

Check and obey the laws and regulations on the use of mobile devices in the

area where you drive. The use of wireless devices and their accessories in

your area may be prohibited or restricted. The use of wireless phones while

driving may cause distraction. Discontinue a call if you can’t concentrate on

driving. When using your mobile device while driving, please:

• Give full attention to driving and to the road.

• Use your hands-free solution to perform hands-free calls.

• Pull off the road and park before making or answering a call if driving

conditions so require.

Caution about high volume usage

Warning: Exposure to loud noise from any source for extended periods of

time may temporarily or permanently affect your hearing. The louder the

volume sound level, the less time is required before your hearing could be

affected. Hearing damage from loud noise is sometimes undetectable at ﬁrst

and can have a cumulative effect. To protect your hearing:

• Start your volume control at a low setting and use as low a volume as

possible.

• Limit the amount of time you use headsets or headphones at high volume.

• Where possible, use your headset in a quiet environment with low

background noise.

• Avoid turning up the volume to block out noisy surrounding.

• Turn the volume down if you can’t hear people speaking near you.

If you experience hearing discomfort, including the sensation of pressure or

fullness in your ears, ringing in your ears, or mufﬂed speech, you should stop

listening to the device through your headset or headphones and have your

hearing checked by your doctor.

Français

14

Avant de commencer

Voir ﬁgure 1, page 1

Prenez le temps de vous familiariser avec votre nouvelle oreillette H790.

1 Port de charge

2 Touche d’appel

3 Témoin

4 Bouton marche/arrêt

5 Microphone

6 Touches de volume

7 Tour d’oreille

8 Haut-parleur

IMPORTANT

Selon le pays dans lequel vous avez acheté votre oreillette H790, les

commandes vocales en langue anglaise peuvent, par défaut, être réglées

sur ON (activées) ou OFF (désactivées). Si les commandes vocales sont

réglées sur ON (activées), vous entendez une voix lors de la mise en

marche de l’oreillette, ainsi que lors de son utilisation.

Si vous souhaitez modiﬁer le réglage par défaut des commandes vocales:

Alors que l’oreillette est en marche, appuyez sur l’une des touches de

volume et sur la touche d’appel jusqu’à ce que vous entendiez « voice

prompts on » (commandes vocales activées) ou « voice prompts off »

(commandes vocales désactivées).

Remarque : les commandes vocales sont disponibles en anglais

uniquement.

Français

15

Port de votre oreillette

Voir ﬁgures 2, page 2

Pour tirer le meilleur parti et pour une confort optimal, essayez tous les

embouts fournis.

Par défaut, votre oreillette est à réglée pour être portée à oreille droite. Vous

pouvez toutefois intervertir le tour d’oreille pour la porter à l’oreille gauche.

Pour une qualité et un confort d’écoute optimaux, veillez à placer

correctement l’embout sur votre oreille en dirigeant le microphone de

l’oreillette en direction de votre bouche.

Charge de votre oreillette

Voir ﬁgure 3, page 2

Chargez votre oreillette avant toute utilisation.

Le témoin est rouge ou jaune lorsque la batterie est en charge. Lorsque la

batterie est complètement chargée, le témoin devient vert.

Remarque : il est impossible d’utiliser l’oreillette pendant la charge.

Mise en marche/arrêt de l’oreillette

Glissez le bouton marche/arrêt en position ON/marche. Le témoin clignote

3 fois en bleu, puis clignote 3 fois en bleu et violet (en cas de connexion

à un périphérique) ou reste allumé en bleu (si l’oreillette est prête pour le

couplage).

Glissez le bouton marche/arrêt en position OFF/arrêt (le témoin situé sous le

bouton est rouge). Le témoin clignote 3 fois, puis s’éteint.

Français

16

Couplage et connexion de votre oreillette

Couplage/connexion de base

Une fois la charge terminée, couplez et connectez votre oreillette à votre ou

vos téléphone(s) Bluetooth.

1. Éteignez tous les périphériques Bluetooth précédemment couplés avec

votre oreillette.

2. Activez l’option Bluetooth de votre téléphone.

3. Placez l’oreillette sur votre oreille, puis mettez-la en marche. Le témoin

s’allume en bleu de façon continue.

4. Avec commandes vocales activées (ON):

• Vous entendez le message « ready to pair » (prêt pour le couplage).

• Suivez les commandes vocales pour connecter votre téléphone à votre

oreillette.

• Lorsque vous êtes invité à saisir le code, saisissez 0000.

• Une fois le couplage réussi, vous entendez le message « pairing

complete » (couplage terminé). Une fois la connexion établie, vous

entendez « phone 1 connected » (téléphone 1 connecté) et le témoin

clignote rapidement en bleu et violet.

• OU

• Avec commandes vocales désactivées (OFF):

• Accédez au menu Bluetooth de votre téléphone pour la recherche de

périphériques.

• Sélectionnez Motorola H790.

• Quand le couplage entre l’oreillette et votre téléphone est réussi, le

témoin clignote en violet et en bleu, puis deux tonalités ascendantes

retentissent.

Français

17

Couplage et connexion avec 2 périphériques (facultatif)

1. Éteignez d’abord votre téléphone et tous les périphériques Bluetooth

précédemment couplés avec votre oreillette.

2. Éteignez votre oreillette.

3. Activez l’option Bluetooth de votre téléphone.

4. Placez l’oreillette sur votre oreille, puis mettez-la en marche. Le témoin

s’allume en bleu de façon continue.

5. Avec commandes vocales activées (ON):

• Vous entendez le message « ready to pair » (prêt pour le couplage).

• Suivez les messages vocaux pour connecter votre téléphone à votre

oreillette.

• Une fois le couplage réussi, vous entendez le message « pairing

complete » (couplage terminé). Une fois la connexion établie, vous

entendez « phone 1 connected » (téléphone 1 connecté) et le témoin

clignote rapidement en bleu et violet.

• Pour connecter les deux téléphones simultanément, il vous suffit de

mettre votre premier téléphone en marche alors que le second est déjà

connecté. Lorsque vous entendez « phone 2 connected » (téléphone 2

connecté), votre oreillette est alors connectée aux deux téléphones.

• OU

• Avec commandes vocales désactivées (OFF):

• Accédez au menu Bluetooth de votre téléphone pour la recherche de

périphériques.

• Sélectionnez Motorola H790.

• Pour connecter les deux téléphones simultanément, il vous suffit de

mettre votre premier téléphone en marche alors que le second est déjà

connecté. Lorsque vous entendez 2 tonalités ascendantes, votre oreillette

est alors connectée aux deux téléphones.

Remarque : le dernier téléphone couplé (votre second téléphone) est

désormais votre téléphone principal (ou « téléphone 1 ») pour les fonctions de

numérotation vocale, que les commandes vocales soient activées ou non.

La page charge ...

Motorola H790 - Headset - Monaural Guide de démarrage rapide

Motorola H790 - Headset - Monaural Guide de démarrage rapide

dans d''autres langues

Documents connexes

Autres documents