Vari-Lite VLZ SPOT Guide de démarrage rapide

1

Introduction

About This Guide

This Quickstart Guide is intended for a knowledgeable user to unpack, install, and use the VLZ SPOT Luminaire in a short time period.

For the complete manual in PDF format, please visit our web site at: www.vari-lite.com and click the user manual download link on the

product downloads page. The complete manual provides you all information related to accessories, menu structures, DMX channel

mapping/ modes, and care for your new luminaire.

Read this manual in its entirety before operating luminaire. Keep this guide for future reference.

WARNING: It is important to read ALL accompanying safety and installation instructions to avoid damage to the product and potential

injury to yourself or others. AVERTISSEMENT: Il est important de lire toutes les instructions de sécurité et d'installation

d'accompagnement pour éviter d'endommager le produit et les risques de blessures à vous-même ou les autres.

Notes:

 For complete product description, features, and specifications, refer to product specification sheet on the Vari-Lite

web site at www.vari-lite.com.

 For power requirements, refer to “Current vs. Voltage” on page 8”.

 VLZ SPOT Luminaires accept glass gobos only. Use of metal gobos will void the luminaire’s warranty.

Additional Documentation

For more information on installing DMX512 control systems, the following publication is available for purchase from the United States

Institute for Theatre Technology (USITT), "Recommended Practice for DMX512: A Guide for Users and Installers, 2nd edition"

(ISBN: 9780955703522). USITT Contact Information:

USITT

315 South Crouse Avenue, Suite 200

Syracuse, New York 13210-1844 USA

Phone: 800-938-7488 or +1-315-463-6463

Fax: 866-398-7488 or +1-315-463-6525

Web Site: www.usitt.org

Customer Service

Our Goal

At Vari-Lite, we are committed to providing you the highest quality in customer service. Our comprehensive resources are available to

help your business succeed and ensure you get the full benefit of being a Vari-Lite customer. Whether your needs are telephone

troubleshooting assistance, product training or technical service, our full-time staff of experienced professionals are on-hand to provide

support.

How to Reach Us

For assistance in your area, call the dealer from which your product was purchased.

or Contact an Authorized Service Center

or Contact the Vari-Lite Customer Service Department, 7am - 6pm CST Monday through Friday, at the following:

phone:1-877-VARI-LITE (1-877-827-4548) or +1-214-647-7880

e-mail: entertainment.service@philips.com

Note: Performing maintenance procedures may void the product warranty. Refer to the Vari-Lite Limited Warranty card included in the

product shipping package for more information. For all service and maintenance issues, please contact your local Authorized

VARI*LITE Dealer or Service Center.

Additional Resources

For additional resources and documentation on this product, please visit our website at www.vari-lite.com and follow the Support link.

Document Number: 02.9708.0001 Version as of: 10 January 2017

VL6000 Beam Luminaire QuickStart Guide

3

Compliance & Safety Notices

Compliance

This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of FCC Rules.

These limits are designed to provide reasonable protection against harmful interference when this equipment is operated in a

commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in

accordance with Vari-Lite system, service, and safety guidelines, may cause harmful interference to radio communications.

As tested under this standard:

FCC 47CFR 15B clA*CEI

Issued:2009/10/01 Title 47 CFR Part 15 Subpart B Unintentional Radiators Class A

Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to

correct the interference at his/her own expense.

EC Declaration of Conformity

We, Vari-Lite B.V., 10911 Petal Street, Dallas, Texas 75238, declare under our responsibility for the products contained herein are in

conformity with the essential requirements of the following European Directives and harmonized standards: Low Voltage

Director (LVD), 2006/95/EC EN 60589-2-17:1984+A1:1987+A2:1990 used in conjunction with 60598-1:2008/A11:2009

Electromagnetic Compatibility Directive (EMC), 2004//108/EC EN 55022:2010, EN55024:2010

Safety Notice

It is extremely important to read ALL safety information and instructions provided in this manual and any accompanying documentation before

installing and operating the products described herein. Heed all cautions and warnings during installation and use of this product. Safety symbols

used throughout this manual are as follows:

CAUTION advising of potential damage to product.

WARNING advising of potential injury or death to persons.

GENERAL INFORMATION PERTAINING TO PROTECTION AGAINST ELECTRICAL SHOCK, FIRE, EXPOSURE TO EXCESSIVE UV

RADIATION, AND INJURY TO PERSONS CAN BE FOUND BELOW.

WARNING: INSTRUCTIONS FOR CONTINUED PROTECTION AGAINST FIRE

1 Luminaires may be mounted on any type of surface as long as mounting instructions are followed. See instructions detailed in this manual.

2 Note distance requirement from combustible materials or illuminated objects for VARI❋LITE luminaires.

WARNING: INSTRUCTIONS FOR CONTINUED PROTECTION AGAINST ELECTRICAL SHOCK

1 VARI❋LITE luminaires are designed for dry locations only. Exposure to rain or moisture may damage luminaire.

2 Disconnect power before servicing any VARI❋LITE equipment.

3 Servicing to be performed by qualified personnel only.

WARNING: INSTRUCTIONS FOR CONTINUED PROTECTION AGAINST EXCESSIVE

EXPOSURE TO UV RADIATION

1 It is hazardous to operate luminaires without lens or shield. Shields, lenses, or ultraviolet screens shall be changed if they have become

visibly damaged to such an extent that their effectiveness is impaired. For example, by cracks or deep scratches. Replace any cracked or

protective shields.

FCC

4

WARNING: INSTRUCTIONS FOR PROTECTION AGAINST INJURY TO PERSONS

1 Exterior surfaces of the luminaire will be hot during operation. Use appropriate safety equipment (gloves, eye protection, etc.) when handling

and adjusting hot equipment and components.

WARNING: RF INTERFERENCE

This is a Class A product. In a domestic environment this product may cause radio interference, in which case, the user may be required to take

adequate measures.

Notes de sécurité

Avant de procéder à l’installation des produits décrits dans ce guide et de les mettre en marche, il est extrêmement important de lire TOUS les

renseignements et TOUTES les directives de sécurité contenues dans ce guide ainsi que toute documentation jointe. Tenir compte de tous les

avertissements et suivre toutes les précautions pendant l’installation et l’utilisation de cet appareil. Les symboles de sécurité utilisés dans ce guide sont

les suivants :

ATTENTION Ce symbole annonce que l’appareil risque d’être endommagé.

AVERTISSEMENT Ce symbole annonce qu’il y a risque d’accident grave ou même fatal.

CETTE SECTION CONTIENT DES INFORMATIONS GÉNÉRALES POUR SE PROTÉGER CONTRE LES DÉCHARGES

ÉLECTRIQUES , LES INCENDIES, L’EXPOSITION EXCESSIVE AUX RAYONS UV ET TOUT AUTRE ACCIDENT POUVANT

ENTRAÎNER DES BLESSURES.

AVERTISSEMENT: DIRECTIVES POUR SE PROTÉGER CONTRE LES INCENDIES

1 Les luminaires peuvent être fixés sur tout type de surface tant que les directives de montage sont respectées. Voir les explications détaillées

dans ce guide.

2 Vérifier la distance à respecter entre les matériaux combustibles ou les objets illuminés et les luminaires VARI❋LITE.

AVERTISSEMENT: DIRECTIVES POUR SE PROTÉGER CONTRE LES DÉCHARGES

ÉLECTRIQUES

1 Débrancher l’appareil avant de procéder à la révision de tout matériel VARI❋LITE.

2 Les révisions doivent être effectuées uniquement par des personnes qualifiées.

AVERTISSEMENT: DIRECTIVES POUR SE PROTÉGER CONTRE UNE EXPOSITION

EXCESSIVE AUX RAYONS UV

1 L’utilisation des luminaires sans lentille ou blindage pose des risques. Tous blindages, lentilles ou écrans ultraviolet visiblement endommagés

au point que leur efficacité en est affectée doivent être remplacés, par exemple s’il y a des fissures ou de profondes rayures.

AVERTISSEMENT: DIRECTIVES POUR SE PROTÉGER CONTRE LES ACCIDENTS POUVANT

ENTRAÎNER DES BLESSURES

1 Les surfaces externes du luminaire deviennent brûlantes quand l’appareil est en marche. Pour manœuvrer ou ajuster des appareils brûlants et

leurs composants, se protéger suffisamment (gants, protection pour les yeux, etc.).

AVERTISSEMENT:

5

INTERFÉRENCE RF

Cet appareil est de Classe A. Dans un environnement domestique, cet appareil peut causer des interférences radio, et si c’est le cas,

l’utilisateur peut avoir à prendre des mesures adéquates.

Other

Battery Information / Informations sur la batterie

 This unit has a battery. Warning: Caution risk of explosion if battery is replaced by an

incorrect type. Dispose of used batteries according to the instructions.

 Cet appareil dispose d'une batterie. Avertissement: Attention risque d'explosion si la batterie

de remplacement par un type incorrect. Jetez les piles usageesselon les instructions.



6

About The VLZ SPOT Luminaire Included Items

Included Items

The following illustration shows all items included with the luminaire:

Figure 1: VLZ SPOT Luminaire Included Items

Note: * Please Check with the local Vari-Lite Office or Authorized Vari*Lite dealer for availability on accessories.

QuickStart Guide(this document)

Neutrik® powerCON® True1

AC Input Connector

7

Connecting Power and Data

Connecting Power

The luminaire requires standard AC power distribution from AC120-240V~, 50/60Hz. Current required depends on the AC supply

voltage and product model. Refer to “Current vs. Voltage” on page 8 for all models covered in this manual.

Note: The mating Neutrik® powerCON® True1 connector is supplied; however, you will need to purchase or construct a cable

appropriate for your application.

Figure 2: Power Connector

Depending on the application, the luminaire’s AC input cable may require a different connector. If required, install a new connector

meeting your requirements using the following wire color code reference:

Wire*

Connection

Green

AC Ground

White

AC Neutral

Blcak

AC Line

* International (Harmonized) Standard

WARNING: DO NOT connect to three-phase service in countries with 240 volt power. AVERTISSEMENT: NE PAS se connecter au

service en trois phases dans les pays avec puissance de 240 volts.

8

For single-phase power at 240 volts RMS:

Connection

AC Neutral

X

AC Line

Y

Ground(Earth)

G

For three-phase power at 208 volts RMS:

Connection

Phase 1

X

Phase 2

Y

Ground (Earth)

G

WARNING: It is not recommended to power any VARI❋LITE luminaire from a dimmer - even in 'NONDIM' mode. Dimmer and

non-dim modules are not suitable sources of power because their output modifies the AC wave form. This may work for a short time,

but will eventually result in power problems, luminaire mis-operation and/or failure and may void the luminaire’s warranty.

AVERTISSEMENT: Il n'est pas recommandé pour alimenter un luminaire VARI❋LITE d'un gradateur - même en mode 'NONDIM.

Modules de gradation et non sombres ne sont pas des sources appropriées de pouvoir parce que leur production modifie la forme d'onde

AC. Cela peut fonctionner pendant une courte période, mais finira par entraîner des problèmes d'alimentation, luminaires mauvais

fonctionnement et / ou l'échec et peut annuler la garantie de l'appareil.

Current vs. Voltage

AC Power Operation

When connected to an AC source, the unit operates on 100 to 240 volts AC (+/- 10%, auto-ranging). The luminaire contains an auto-ranging power

supply.Each luminaire can draw up to 850 Watts.

WARNING: It is the responsibility of the user to adequately protect supply source with a correct size and type circuit breaker and not

overload circuits. AVERTISSEMENT: Il est de la responsibilité de l'utilisateur de protéger adéquatement la source d'alimentation

avec une taille correcte et le disjoncteur de type et surchargez pas les circuits.

Connecting Data

A maximum of 32 luminaires may be connected in any one DMX data link.

Note: This maximum limit applies to the luminaire "daisy chain" only. Your system or console may require fewer luminaires on a

single data link path. Consult your console documentation for more information.

To connect power and data:

Step 1. Connect data cable from console to first luminaire in chain at DATA IN connector.

Step 2. If required, connect additional data cables from DATA THRU connectors to DATA IN connectors of remaining luminaires in link.

Step 3. At last luminaire in link, install male termination connector at DATA THRU connector. (Luminaires and other devices on the same DMX

chain may not function properly without termination.)

9

Figure 3: Data Link

Step 4. Connect AC Input Cable connector to power input source.

Step 5. Dress AC input and data cables and secure them so that they will not interfere with luminaire head and yoke movement.

10

Installation Procedures

Floor Mounting the Luminaire

All luminaires included in this manual are designed to sit directly on its base in a floor installation application. When used in this type of

application, be sure to leave enough space around the luminaire to allow proper, uninterrupted airflow for cooling and movement.

Hanging the Luminaire

The VLZ SPOT Luminaire can be hung horizontally or vertically from any structure designed to work with the type of load created by this

moving luminaire. Two mounting truss hooks or other mounting hardware are required. Many compatible truss hooks are available from different

manufacturers for your particular needs. A minimum of two hooks per luminaire is required. If mounting method does not use truss hooks, two

attachment points, per luminaire, are required.

Install mounting hardware and brackets:

Step 1. Install truss hooks on two provided truss hook brackets as required as shown in Figure 4.

Step 2. Determine required configuration of bracket installation. Brackets may be installed in

many different orientations as shown in Figure 5.

Step 3. While pulling up on locking mechanism release, fit keyed holes onto raised mounting buttons at

bottom of enclosure. Slide forward and release locking mechanism to lock in place. Ensure brackets are

locked securely.

WARNING: Ensure that the bracket locking mechanism is fully seated after the bracket is

installed on the luminaire. AVERTISSEMENT: Assurez-vous que le mécanisme de support

de verrouillage est complètement inséré après le support est installé sur l'appareil.

11

Figure 5: Installing Brackets on Luminaire Enclosure

12

Menu Operation

LCD Display and Menu System

The VLZ SPOT Luminaire’s LCD Display and Menu System provides local control for accessing the following fixture’s settings:

 Address – to set the DMX address

 Configure – various parameter settings

 Fixture – fixture status, recalibrate, reboot, software version, view fixtures hours, etc.

 DMX – change the map mode, invert pan/tilt ，check DMX real time data.

 Manual – manual control of parameters

 Test – test functions of parameters

The menu system is controlled at the Menu Display available at the enclosure input panel. If there are multiple luminaires in a system,

any settings or changes would need to be made at each LCD Menu as desired.

Menu Controls

The menu system is controlled by an MODE/ESC, , and four Arrow ( ) buttons. These buttons function are

shown in Figure 6.

Figure 6: Menu Controls

LCD Display and Menu System Operation

The LCD Display Menu system consists of several categories. Use the Menu Buttons to access and make changes to the menu items.

When the desired menu item is reached, press the desired Menu Button to display the menu options and to navigate and configure the

menu options as required.

To navigate and access menu settings/selections:

Step 1. Make sure unit is powered and turned on.

Step 2. Press [MODE/ESC] to access menu categories.

13

Step 3. Use four Arrow ( ) buttons to navigate through the various options and settings.

Step 4. Once menu item is reached, press OK [Enter] to access the menu item parameters.

Step 5. Make changes to parameters as desired.

Step 6. Press button to accept changes.

Other LCD Display Features

LCD Menu Battery Operation

The LCD menu system utilizes a battery powered system for operation when the luminaire is not connected to power. The primary

purpose of this mode is to allow basic setup and configuration of the luminaire.

To enable the battery operation of the menu system:

Step 1. Press [Mode] three seconds to activate display!

Step 2. Once enabled, the menu will function as normal with only the following sub-menu sections active:

 Address

 Configure

 DMX

 Fixture

Note: Any commands that require full power (calibrate, etc.) will be ignored while the menu system is in battery operation mode.

Step 3. To exit battery mode, press [MODE/ESC] three seconds.

Status Bar

The Status Bar (as illustrated in Figure 7) is present at all times and displays

luminaire operational information of the luminaire. The Status Bar contains the

following information:

 LED - indicates current lamp state - ON or OFF.

 ERRORS –Displays a number indicating the total amount of current errors. When

errors are present, messages will appear in Red text. When no errors are present, NO

will display.

 SHDN – indicates hibernate mode – YES or NO

 MODE：indicate fixture power mode，STA- Standard Mode，STE-- Studio Mode

 MAP – Displays the current DMX map mode setting. 16E--16-bit Enh Mode;16—16 bit Mode

 ADDR – Displays the current DMX address for the fixture. NOTE, when the fixture does not detect a DMX input signal, the

DMX address text will display in Red text.

Figure 7: LCD display Status Bar

14

Quick Reference DMX Map

DMX

Channel

Parameter

Range DMX

Defaults

Description

Intensity

0-65535

0

16-bit control of Fixture Intensity from 0 - 100%

1

High Byte

2

Low Byte

Pan

0 - 65535

32767

16-bit linear control of pan from 0°-540°.

3

High Byte

With Expanded Movement turned on, 630° of pan is possible

4

Low Byte

Tilt

0 - 65535

32767

16-bit linear control of tilt from 0°-270°.

5

High Byte

6

Low Byte

Edge

0 - 65535

32767

16-bit linear control of edge functions

7

High Byte

8

Low Byte

Zoom

0 - 65535

32767

16-bit linear control of fixture zoom range between

9

High Byte

0 (narrow) to 65535 (wide).

10

Low Byte

11

Programming

0 - 255

0

Used as a control channel for different programmable settings.

Control

Set value of desired effect.

0 - 2

→

Idle

3 - 5

→

Linear Dimming Curve

6 - 10

→

Square Law Dimming Curve

11 - 15

→

TV Dimming Curve

16 - 20

→

Architectural Dimming Curve

51 - 55

→

Edge Track ON

56 - 60

→

Edge Track ON

61 - 65

→

Edge Track ON

66 - 70

→

Edge Track OFF

Cyan

0 - 65535

0

16 Bit control of cyan color mechanism.

12

High Byte

13

Low Byte

Yellow

0 - 65535

0

16 Bit control of yellow color mechanism.

14

High Byte

15

Low Byte

Magenta

0 - 65535

0

16 Bit control of Magenta color mechanism.

16

High Byte

17

Low Byte

CTO

0 - 65535

0

16 Bit contol of CTO mechanism.

18

High Byte

19

Low Byte

15

20

Color Wheel

0 - 255

0

8-bit linear control of Color Wheel 1. See Channel 16 for

options.

1

0 - 16

→

1. Open

17 -33

→

2. (Open/Color 1)

34 - 50

→

3. (Color 1)

51 - 67

→

4. (Color 1/Color 2)

68 - 84

→

5. (Color 2)

85 - 101

→

6. (Color 2/Color 3)

102 - 118

→

7. (Color 3)

119 - 135

→

8. (Color 3/Color 4)

136 - 152

→

9. (Color 4)

153 - 169

→

10. (Color 4/Color 5)

170 - 186

→

11. (Color 5)

187 - 203

→

12. (Color 5/Color 6)

204 - 220

→

13. (Color 6)

221 - 237

→

14. (Color 6/Open)

238 - 255

→

15. (Open)

DMX

Channel

Parameter

Range DMX

Defaults

Description

21

Color Wheel

1

0 - 255

0

Used as a control channel for different movement options of

Color

Control

Wheel 1.

0 - 5

→

Linear Movement using shortest (quickest) path.

6 - 10

→

Linear Movement using normal (longest) path.

11 - 15

→

Wheel Spin Forward (Fast to Slow)

16 - 20

→

Wheel Spin STOP

21 - 25

→

Wheel Spin Reverse (Slow to Fast)

26 - 56

→

Color Shake Quickest Path (Slow to Fast)

57 - 87

→

Color Shake Normal Path (Slow to Fast)

88 - 255

→

Reserved Values

22

Color Wheel

0 - 255

0

8-bit linear control of Color Wheel 1. See Channel 16 for

options.

2

0 - 16

→

1. Open

17 -33

→

2. (Open/Color 1)

34 - 50

→

3. (Color 1)

51 - 67

→

4. (Color 1/Color 2)

68 - 84

→

5. (Color 2)

85 - 101

→

6. (Color 2/Color 3)

102 - 118

→

7. (Color 3)

16

119 - 135

→

8. (Color 3/Color 4)

136 - 152

→

9. (Color 4)

153 - 169

→

10. (Color 4/Color 5)

170 - 186

→

11. (Color 5)

187 - 203

→

12. (Color 5/Color 6)

204 - 220

→

13. (Color 6)

221 - 237

→

14. (Color 6/Open)

238 - 255

→

15. (Open)

23

Color Wheel

2

0 - 255

0

Used as a control channel for different movement options of

Color

Control

Wheel 1.

0 - 5

→

Linear Movement using shortest (quickest) path.

6 - 10

→

Linear Movement using normal (longest) path.

11 - 15

→

Wheel Spin Forward (Fast to Slow)

16 - 20

→

Wheel Spin STOP

21 - 25

→

Wheel Spin Reverse (Slow to Fast)

26 - 56

→

Color Shake Quickest Path (Slow to Fast)

57 - 87

→

Color Shake Normal Path (Slow to Fast)

88 - 255

→

Reserved Values

24

Gobo Wheel

1

0 - 255

0

8-bit control of Gobo Wheel 2. See Channel 27 for control

options.

(Rotating

Gobo Wheel)

0 - 5

→

Open - No Gobo

6 - 10

→

Gobo 1 (Leafy Breakup) Index）

11 - 15

→

Gobo 2 (Wavy Triangle) Index

16 - 20

→

Gobo 3 (Lattice) Index

21 - 25

→

Gobo 4 (Swirl) Index

26 - 30

→

Gobo 5 (Radial Breakup) Index

31 - 35

→

Gobo 6 (Neurons) Index

36 - 40

→

Gobo 7 (Grid) Index

41 - 45

→

Open - No Gobo

46 - 50

→

Gobo 1 (Leafy Breakup) Rotate

51 - 55

→

Gobo 2 (Wavy Triangle) Rotate

56 - 60

→

Gobo 3 (Lattice) Rotate

61 - 65

→

Gobo 4 (Swirl) Rotate

66 - 70

→

Gobo 5 (Radial Breakup) Rotate

71 - 75

→

Gobo 6 (Neurons) Rotate

76 - 80

→

Gobo 7 (Grid) Rotate

81 - 85

→

Open - No Gobo

86 - 90

→

Gobo 1 (Leafy Breakup) Rotate with Mega Stepping

91 - 95

→

Gobo 2 (Wavy Triangle) Rotate with Mega Stepping

17

96 - 100

→

Gobo 3 (Lattice) Rotate with Mega Stepping

101 - 105

→

Gobo 4 (Swirl) Rotate with Mega Stepping

106 - 110

→

Gobo 5 (Radial Breakup) Rotate with Mega Stepping

111 - 115

→

Gobo 6 (Neurons) Rotate with Mega Stepping

116 - 120

→

Gobo 7 (Grid) Rotate with Mega Stepping

121 - 255

→

Reserved Values

Gobo 1

Rot/Index

0 - 65535

32767

16-bit control of index and rotation of gobo wheel 1.

25

High Byte

0~126

→

Rotate Fast to Slow <<<

127~128

→

Rotation STOP

129- 255

→

Rotate Slow to Fast >>>

26

Low Byte

DMX

Channel

Parameter

Range DMX

Defaults

Description

27

Gobo Wheel

1

0 - 255

0

Used as a control channel for different movement options for

Control

Gobo Wheel 1 (Channel 24).

0 - 5

→

Gobo Selection using shortest (quickest) path.

6 - 10

→

Gobo Selection using normal (longest) path.

11 - 20

→

Reserved Values

21 - 50

→

Wheel Spin Forward (Fast to Slow)

51 - 60

→

Wheel Spin STOP

61 - 90

→

Wheel Spin Reverse (Slow to Fast)

91 - 120

→

Gobo Shake Quickest Path (Slow to Fast)

121 - 150

→

Gobo Shake Normal Path (Slow to Fast)

151 - 180

→

Gobo Twist Quickest Path (Slow to Fast)

181 - 210

→

Gobo Twist Normal Path (Slow to Fast)

211 - 255

→

Reserved Values

28

Gobo Wheel

2

0 - 255

0

8-bit control of Gobo Wheel 2. See Channel 27 for control

options.

(Rotating

Gobo Wheel)

0 - 5

→

Open - No Gobo

6 - 10

→

Gobo 1 (Night Sky) Index

11 - 15

→

Gobo 2 (Circle of Ovals) Index

16 - 20

→

Gobo 3 (Bricked Out) Index

21 - 25

→

Gobo 4 (Punch Card) Index

26 - 30

→

Gobo 5 (Alpha Rays) Index

31 - 35

→

Gobo 6 (HONEYCOMB) Index

18

36 - 40

→

Gobo 7 (On the Rocks) Index

41 - 45

→

Open - No Gobo

46 - 50

→

Gobo 1 (Night Sky) Rotate

51 - 55

→

Gobo 2 (Circle of Ovals) Rotate

56 - 60

→

Gobo 3 (Bricked Out) Rotate

61 - 65

→

Gobo 4 (Punch Card) Rotate

66 - 70

→

Gobo 5 (Alpha Rays) Rotate

71 - 75

→

Gobo 6 (HONEYCOMB) Rotate

76 - 80

→

Gobo 7 (On the Rocks) Rotate

81 - 85

→

Open - No Gobo

86 - 90

→

Gobo 1 (Night Sky) Rotate with Mega Stepping

91 - 95

→

Gobo 2 (Circle of Ovals) Rotate with Mega Stepping

96 - 100

→

Gobo 3 (Bricked Out) Rotate with Mega Stepping

101 - 105

→

Gobo 4 (Punch Card) Rotate with Mega Stepping

106 - 110

→

Gobo 5 (Alpha Rays) Rotate with Mega Stepping

111 - 115

→

Gobo 6 (HONEYCOMB) Rotate with Mega Stepping

116 - 120

→

Gobo 7 (On the Rocks) Rotate with Mega Stepping

121 - 255

→

Reserved Values

Gobo 2

Rot/Index

0 - 65535

32767

16-bit control of index and rotation of gobo wheel 1.

29

High Byte

0~126

→

Rotate Fast to Slow <<<

127~128

→

Rotation STOP

129- 255

→

Rotate Slow to Fast >>>

30

Low Byte

DMX

Channel

Parameter

Range DMX

Defaults

Description

31

Gobo Wheel

2

0 - 255

0

Used as a control channel for different movement options for

Control

Gobo Wheel 1 (Channel 24).

0 - 5

→

Gobo Selection using shortest (quickest) path.

6 - 10

→

Gobo Selection using normal (longest) path.

11 - 20

→

Reserved Values

21 - 50

→

Wheel Spin Forward (Fast to Slow)

51 - 60

→

Wheel Spin STOP

61 - 90

→

Wheel Spin Reverse (Slow to Fast)

91 - 120

→

Gobo Shake Quickest Path (Slow to Fast)

121 - 150

→

Gobo Shake Normal Path (Slow to Fast)

151 - 180

→

Gobo Twist Quickest Path (Slow to Fast)

181 - 210

→

Gobo Twist Normal Path (Slow to Fast)

211 - 255

→

Reserved Values

19

32

Iris

0 - 255

0

Controls Iris mechanism from open (DMX 0) to Full (DMX

255).

33

Prism

0 - 255

0

Controls Prism mechanism with following values.

0 - 5

→

Open

6 - 10

→

Index

11 - 15

→

Rotate Normal

16 - 20

→

Rotate with Mega Stepping

21 - 255

→

Reserved Values

Prism

Index/Rot

0 - 65535

32767

16-bit control of prism rotation and index.

34

High Byte

0~126

→

Rotate Fast to Slow <<<

127~128

→

Rotation STOP

129- 255

→

Rotate Slow to Fast >>>

35

Low Byte

36

Frost

0 - 255

0

Insert control of frost mechanism with the following values.

0 - 50

→

Open - No Frost or Diffusion

51 - 100

→

Insert Light Diffusion

101 - 150

→

Insert Heavy Frost

151 - 200

→

Insert both Light Diffusion and Heavy Frost

37

Strobe

0 - 255

0

Controls Strobe functionality.

0 - 3

→

Open

4 - 6

→

Closed

7 - 32

→

Normal Strobe - Slow to Fast

33 - 58

→

Random Strobe - Slow to Fast

59 - 84

→

Random Sync - Slow to Fast

85 - 110

→

Pulse > - Slow to Fast

111 - 136

→

Pulse > Random - Slow to Fast

137 - 162

→

Pulse > Random Sync - Slow to Fast

163 - 188

→

Pulse < - Slow to Fast

189 - 214

→

Pulse < Random - Slow to Fast

215 - 240

→

Pulse < Random Sync - Slow to Fast

38

Focus Timing

0 - 255

255

Adjustment of fixture timing to control Pan/Tilt mechanisms.

- See Timing Channel Chart in User Manual

39

Optics

Timing

0 - 255

255

Adjustment of fixture timing to control lensing mechanisms.

- See Timing Channel Chart in User Manual

20

DMX

Channel

Parameter

Range DMX

Defaults

Description

40

Color Timing

0 - 255

255

Adjustment of fixture timing to control color mechanisms.

- See Timing Channel Chart in User Manual

41

Beam Timing

0 - 255

255

Adjustment of fixture timing to control beam shaping

mechanisms.

- See Timing Channel Chart in User Manual

42

Gobo Timing

0 - 255

255

Adjustment of fixture timing to control gobo mechanisms.

- See Timing Channel Chart in User Manual

43

Luminaire

0 - 255

0

Control Channel used for full fixture settings, lamp controls, and

Control

miscellaneous modes.

Set descreet value of desired effect, wait >3 seconds, then set

value to 0 (Idle).

0 - 5

→

Idle (Default)

6 - 10

→

Full Luminaire ReCal - Also Used to Wake fixture up from

shutdown

11 - 15

→

Reserved Values

16 - 20

→

Reserved Values

21 - 25

→

Fixture Shutdown

26 - 30

→

Display - Menu ON

31 - 35

→

Display - Menu OFF

36 - 40

→

ReCal Position

41 - 45

→

ReCal Color

46 - 50

→

ReCal Gobo

51 - 55

→

ReCal Beam

56 - 60

→

ReCal Optics

61 - 65

→

ReCal Dimmer/Strobe

66 - 70

→

Reset Fixture to Defaults - See Manual for a list of factory

defaults.

71 - 75

→

Full Luminaire Reboot. This command will reset all processors

in

fixture, then ReCal all parameters.

76 - 80

→

Fixture Status On/Off. This command will enable the display

to

show fixture status for 5 min. After this time, displays will

return

to default configuration. Repeating this command in less than

5

minutes will behave as a toggle.

81 - 85

→

Standard Mode - Fixture operates at maximum output (Default)

86 - 90

→

Studio Mode - Reduced output with lower fan settings

91 - 255

→

Reserved Values

La page charge ...

Vari-Lite VLZ SPOT Guide de démarrage rapide

Vari-Lite VLZ SPOT Guide de démarrage rapide

dans d''autres langues

Documents connexes

Autres documents