Frigidaire FPIC3077RF Manuel utilisateur

Marque: Frigidaire

Modèle: FPIC3077RF

Catégorie: Cuisinières

Taper: Manuel utilisateur

Ce manuel convient également à

FPIC3677RF

TABLE OF CONTENTS

www.frigidaire.com USA 1-800-944-9044 www.frigidaire.ca Canada 1-800-265-8352

All about the

Use & Care

of your Cooktop

Welcome & Congratulations ...................................2

Important Safety Instructions ................................. 3

Cooktop Features ..................................................7

Before Using the Cooktop ......................................8

A01704801 (August/ 2016) Rev. C

Setting Induction Surface Controls ........................10

Care & Cleaning ..................................................15

Before You Call ..................................................17

Major Appliance Warranty ....................................19

WELCOME & CONGRATULATIONS



NOTE

Please attach sales receipt here for future reference.

Please record your model and serial numbers

below for future reference.

Model Number:

Serial Number:

Purchase Date:

Printed in China

Congratulations on your purchase of a new appliance! At

Electrolux Home Products, we are very proud of our

product and are completely committed to providing you

with the best service possible. Your satisfaction is our

number one priority.

We know you’ll enjoy your new appliance and Thank You

for choosing our product. We hope you consider us for

future purchases.

PLEASE CAREFULLY READ AND SAVE THESE

INSTRUCTIONS

This Use & Care Manual contains general operating

instructions for your appliance and feature information

for several models. Your product may not have

all the described features. The graphics shown are

representative. The graphics on your appliance may not

look exactly like those shown. These instructions are not

meant to cover every possible condition and situation

that may occur. Common sense and caution must be

practiced when installing, operating and maintaining any

appliance.

Product Registration

Serial Plate Location

Cooktop Serial

Plate Location

The PRODUCT

REGISTRATION CARD

should be lled in completely,

signed and returned to

Electrolux Home Products.

IMPORTANT SAFETY INSTRUCTIONS

WARNING

This symbol will help alert you to situations that may

cause serious bodily harm, death or property damage.

IMPORTANT

IMPORTANT indicates installation, operation or

maintenance information which is important but not

hazard-related.

CAUTION

This symbol will help alert you to situations that may

cause bodily injury or property damage.

DEFINITIONS

This is the safety alert symbol. It is used to alert

you to potential personal injury hazards. Obey all safety

messages that follow this symbol to avoid possible injury

or death.

Read all instructions before using this appliance.

This manual contains important safety symbols and

instructions. Pay attention to these symbols and follow all

instructions given.

Do not attempt to install or operate your appliance until

you have read the safety precautions in this manual.

Safety items throughout this manual are labeled with a

WARNING or CAUTION statement based on the risk type.

Warnings and important instructions appearing in this

guide are not meant to cover all possible conditions and

situations that may occur. Common sense, caution, and

care must be exercised with installing, maintaining, or

operating your appliance.



NOTE

Indicates a short, informal reference – something

written down to assist the memory or for future

reference.

GROUNDING INSTRUCTIONS

• Proper Installation—Be sure your appliance is

properly installed and grounded by a qualied

technician. In the United States, install in accordance

with the National Fuel Gas Code ANSI Z223.1/

NPFA No. 54, latest edition and National Electrical

Code NFPA No. 70 latest edition, and local electrical

code requirements. In Canada, install in accordance

with CAN/CGA B149.1 and CAN/CGA B149.2 and

CSA Standard C22.1, Canadian Electrical code,

Part 1-latest editions and local electrical code

requirements. Install only per installation instructions

provided in the literature package for this appliance.

• For personal safety, this appliance must be properly

grounded. For maximum safety, the power cord

must be securely connected to an electrical outlet or

junction box that is the correct voltage, is correctly

polarized and properly grounded, and protected by a

circuit breaker in accordance with local codes.

• It is the personal responsibility of the consumer to

have the appropriate outlet or junction box with the

correct, properly grounded wall receptacle installed

by a qualied electrician. It is the responsibility and

obligation of the consumer to contact a qualied

installer to assure that the electrical installation is

adequate and is in conformance with all local codes

and ordinances.

See the installation instructions packaged with this

appliance for complete installation and grounding

instructions.

IMPORTANT INSTRUCTIONS FOR UNPACKING

AND INSTALLATION

IMPORTANT - Read and follow the below instructions and

precautions for unpacking, installing, and servicing your

appliance:

• Remove all tape and packaging wrap before using the

appliance. Destroy the carton and plastic bags after

unpacking the appliance. Never allow children to play

with packaging material. Do not remove the wiring

label and other literature attached to the appliance.

Do not remove model/serial number plate.

• Cold temperatures can damage the electronic control.

When using this appliance for the rst time, or when

the appliance has not been used for an extended

period of time, be sure the appliance has been in

temperatures above 32ºF (0ºC) for at least 3 hours

before turning on the power to the appliance.

• Never modify or alter the construction of the

appliance by removing the leveling legs, panels, wire

covers, anti-tip brackets/screws, or any other part of

the appliance.

• Be sure to have an appropriate foam-type re

extinguisher available, visible, and easily accessible

located near the appliance.

WARNING

If the information in this manual is not followed exactly,

a re or explosion may result causing property damage,

personal injury or death.

FOR YOUR SAFETY: Do not store or use gasoline or

other ammable vapors and liquids in the vicinity of

this or any other appliance.

IMPORTANT SAFETY INSTRUCTIONS

IMPORTANT INSTRUCTIONS FOR USING THE

APPLIANCE

WARNING

• Storage In or On Appliance—Flammable

materials should not be stored in an oven or

microwave, near surface burners or elements, or

in the storage or warmer drawer (if equipped).

This includes paper, plastic, and cloth items, such

as cookbooks, plastic ware, and towels, as well as

ammable liquids. Do not store explosives, such as

aerosol cans, on or near the appliance.

• Do not leave children alone - Children should not

be left alone or unattended in the area where

appliance is in use. They should never be allowed

to sit or stand on any part of the appliance,

including the storage drawer, lower broiler drawer,

warmer drawer, or lower double oven.

• Do not store items of interest to children in the

cabinets above the appliance or on the backguards

of ranges. Children climbing on or near the

appliance to reach items could be seriously injured.

• Do not allow children to climb or play around the

appliance. The weight of a child on an open oven

door may cause the appliance to tip, resulting in

serious burns or other injury. An open drawer when

hot may cause burns.

• Stepping, leaning, or sitting on the door or drawers

of this appliance can result in serious injuries and

also cause damage to the appliance.

WARNING

• Never cover any slots, holes, or passages in the

oven bottom or cover an entire oven rack with any

materials, such as aluminum foil or aftermarket

oven liners. Aluminum foil and other liners may

trap heat, causing a re hazard.

• Never use your appliance as a space heater to

heat or warm the room. Doing so may result in

carbon monoxide poisoning and overheating of the

appliance.

WARNING

• Avoid re hazard or electrical shock. Failure to

follow this warning may cause serious injury, re,

or death.

• Avoid re hazard or electrical shock. Do not use

an adapter plug, use an extension cord, or remove

grounding prong from the power cord. Failure to

follow this warning may cause serious injury, re,

or death.

CAUTION

• When heating fat or grease, watch it closely. Grease

may catch re if it becomes too hot.

• Do not use water or our on grease res. Smother

re or ame or use dry chemical or foam-type

extinguisher. Cover the re with a pan lid or use

baking soda.

• Use dry potholders. Moist or damp potholders on

hot surfaces may result in burns from steam. Do

not let potholders touch hot cooking areas. Do not

use towels or other bulky cloths.

• Do not heat unopened food containers - Build-up of

pressure may cause container to burst and result in

injury.

• Wear proper apparel - Loose-tting or hanging

garments should never be worn while using the

appliance. Do not let clothing or other ammable

materials contact hot surfaces.

• Do not touch surface burners or elements, areas

near these burners or elements, interior surfaces

of the oven, or the warmer drawer (if equipped).

Surface burners and elements may be hot even

though they appear cool. Areas near surface

burners and elements may become hot enough to

cause burns. During and after use, do not touch,

or let clothing or other ammable materials touch

these areas until they are cool. These areas may

include the cooktop, surfaces facing the cooktop,

oven vent areas, oven door, and oven window.

IMPORTANT SAFETY INSTRUCTIONS

• Know which knob or key controls each surface heat-

ing area. Place cookware with food on the cooking

area before turning it on. Turn the cooking area off

before removing the cookware.

• Cookware handles should be turned inward and not

extend over adjacent surface elements. — To reduce

the risk of burns, ignition of ammable materials, and

spillage due to unintentional contact with the utensil,

the handle of the cookware should be positioned so

that it is turned inward, and does not extend over

other cooking areas.

• Glazed cooking utensils — Only certain types of

cookware are suitable for cook top service and must

be magnetic to work properly on the induction zones.

Check the manufacturer’s recommendations for cook

top use to ensure that the cookware is compatible

with induction cooking.

• Improper cookware may break due to sudden

changes in temperature. Check the cookware manu-

facturer’s recommendations for cooktop use.

• Use proper pan size - This appliance is equipped with

one or more surface units of different sizes. Select

cookware with at bottoms that match the surface

unit size. Using the proper cookware on the cooking

area will improve efciency.

CAUTION

Persons with a pacemaker or similar medical device should

exercise caution using or standing near an induction unit

while it is in operation, as the electromagnetic eld may

affect the working of the pacemaker or similar medical

device. It would be advisable to consult your Doctor or

the pacemaker or similar medical device manufacturer

about your particular situation.

• Never leave surface elements unattended. Boil-overs

may cause smoking and greasy spills that may ignite.

A pan that has boiled dry could be damaged and may

damage the cooktop.

• When you are aming foods under a ventilating

hood, turn on the fan.

IMPORTANT INSTRUCTIONS FOR GLASS AND

CERAMIC COOKTOPS

• Do not clean or operate a broken cooktop. If cooktop

should break, cleaning solutions and spillovers may

penetrate the broken cooktop and create a risk of elec-

tric shock. Contact a qualied technician immediately.

• Clean cooktop glass with caution. If a wet sponge or

cloth is used to wipe spills on a hot cooking area, be

careful to avoid a steam burn. Some cleaners can pro-

duce harmful fumes if applied to a hot surface.

• Avoid scratching the cooktop glass with sharp objects.

IMPORTANT INSTRUCTIONS FOR CLEANING YOUR

APPLIANCE

CAUTION

• Before manually cleaning any part of the appliance,

be sure all controls are turned off and the

appliance is cool. Cleaning a hot appliance can

cause burns.

CAUTION

Do not attempt to operate the appliance during a

power failure. If the power fails, always turn off the

appliance. If the appliance is not turned off and the

power resumes, electric surface elements may resume

operation when power is restored. Once the power

resumes, reset the clock and the oven function.

IMPORTANT INSTRUCTIONS FOR YOUR INDUCTION

COOKTOP

• Clean the appliance regularly to keep all parts free of

grease that could catch re. Do not allow grease to

accumulate. Greasy deposits in the fan could catch

re.

• Always follow the manufacturer’s recommended

directions for use of kitchen cleaners and aerosols.

Be aware that excess residue from cleaners and

aerosols may ignite causing damage and injury.

• Clean venitlating hoods frequently - Grease should

not be allowed to accumulate on hood or lter.

Follow the manufacturer’s instructions for cleaning

vent hoods.

IMPORTANT SAFETY INSTRUCTIONS

IMPORTANT SAFETY NOTICE

The California Safe Drinking Water and Toxic

Enforcement Act requires the Governor of California

to publish a list of substances known to the state to

cause cancer, birth defects or other reproductive harm,

and requires businesses to warn customers of potential

exposure to such substances.

Important: This appliance has been tested and found

to comply with the limits for a class B digital device,

pursuant to Part 18 of the FCC rules (United States) and

ICES-001 (Canada). These limits are designed to provide

reasonable protection against harmful interference in a

residential installation. This unit uses and can radiate

radio frequency energy and, if not installed and used

in accordance with the instructions, may cause harmful

interference to radio communications. However there

is no guarantee that interference will not occur in a

particular installation. If this unit does cause harmful

interference to radio or television reception, which can

be determined by turning the unit off and on, the user is

encouraged to try to correct the interference by one or

more of the following measures:

• Reorient or relocate the receiving antennae.

• Increase distance between unit and receiver.

• Connect the unit into an outlet or a circuit different

from that to which the receiver is connected.

IMPORTANT INSTRUCTIONS FOR SERVICE AND

MAINTENANCE

• Do not repair or replace any part of the appliance un-

less specically recommended in the manuals. All other

servicing should be done only by a qualied technician.

This reduces the risk of personal injury and damage

to the appliance.

• Always contact your dealer, distributor, service agent,

or manufacturer about problems or conditions you do

not understand.

• Ask your dealer to recommend a qualied technician

and an authorized repair service. Know how to discon-

nect the power to the appliance at the circuit breaker

or fuse box in case of an emergency.

• Remove the oven door from any unused oven if it is to

be stored or discarded.

• Do not touch a hot oven light bulb with a damp cloth.

Doing so could cause the bulb to break. Handle halogen

lights (if equipped) with paper towels or soft gloves.

Disconnect the appliance or shut off the power to the

appliance before removing and replacing the bulb.

COOKTOP FEATURES

Read these instructions carefully before using the cooktop

1. Left Rear Induction Element

2. Left Front Induction Element

3. Center Front Induction Element (36” model only)

4. Center Rear (30” model only) or Right Rear Induc-

tion Element (36” model only)

5. Right Front Induction Element

6. Left Front Element Control Knob & Indicator

7. Left Rear Element Control Knob & Indicator

8. Center Front Element Control Knob & Indicator (36”

model only)

9. Center Rear Element Control Knob & Indicator

10. Right Front Element Control Knob & Indicator

CAUTION

The Cooking Zones may appear to be cool while turned

ON and after they have been turned OFF. The glass

surface may be HOT from residual heat transferred

from the cookware and burns may occur.

Figure 1

30" Model

Figure 2

36" Model

6 8 9 107

6 7 9 10

Use the Correct Cookware Type

For the induction zones, the magnetic Cooking Zone

sensors located below the cooktop surface require the use

of cookware made with magnetic material in order to start

the heating process on any of the Cooking Zones.

When purchasing pans, look for cookware specically

identied by the manufacturer for use with Induction

cooktops. If you are not sure, use a magnet to test whether

the cookware type will work. If a magnet sticks to the

bottom of the cookware, the material type is correct for

Induction cooking (See Fig. 1).

Fig. 1

It is recommended to always use heavier high quality

stainless steel cookware on your Induction Cooktop

surface. This will greatly reduce the possibility of developing

scratches on the ceramic surface.

Even quality cookware can scratch the cooktop surface,

especially if cookware is slid over the ceramic cooktop

surface without being lifted up. Over time sliding ANY type

of cookware over the ceramic cooktop will likely alter the

overall appearance of the cooktop. Eventually the buildup

of scratches will make cleaning the surface difcult and

degrade the overall appearance of the cooktop.

BEFORE USING THE COOKTOP

Induction Cooktop Features

A COOLER COOKTOP- A unique feature of the

Induction Cooktop is whether turned ON or OFF, the

cooktop surface remains cooler than standard ceramic

cooktops.

The Cooking Zones may appear to be

cool while turned ON and after they have been turned

OFF. The glass surface may be HOT from residual heat

transferred from the cookware and burns may occur.

MAGNETIC DETECTOR- The coil sensor automatically

detects whether the pan is magnetic and eliminates ac-

cidental "turn-On".

PAN SIZE DETECTION- The pan recognition sensor

automatically detects and adapts the Cooking Zones to

the pan sizes in use.

EFFICIENT- Induction cooking heats faster while using

less energy. Induction power levels are quick to boil and

when simmering.

Selecting Surface Cooking Cookware

The cookware used with the Induction Cooktop should have

at bottoms that make good contact with the entire surface

of the Cooking Zone. Check for atness by rotating a ruler

across the bottom of the cookware (See Fig. 2). Be sure to

follow all the recommendations for using cookware.

Figure 2

Prior to using your cooktop for the rst time, apply a

cooktop cleaning creme to the ceramic surface. Buff with

a non-abrasive cloth or pad. This will make cleaning easier

when soiled from cooking. The special cooktop cleaning

cream leaves a protective nish on the glass to help prevent

scratches and abrasions.

Also remember to:

• Use cookware made with the correct material type for

Induction Cooking.

• Use quality cookware with heavier bottoms for better

heat distribution allowing for more even cooking results.

• The pan size should match the amount of food being

prepared.

• Do not let pans boil dry. This may cause permanent

damage in the form of breakage, fusion, or marring that

can affect the ceramic cooktop. (This type of damage is

not covered by your warranty).

• Do not use dirty pans with grease buildup. Always use

pans that are easy to clean after cooking.

CAUTION

• The Cooking Zones may appear to be cool while

turned ON and after they have been turned OFF. The

glass surface may be HOT from residual heat transferred

from the cookware and burns may occur.

• DO NOT SLIDE Cookware across the cooktop surface.

Doing so may permanently damage the appearance of

the ceramic cooktop.

• DO NOT TOUCH HOT COOKWARE or PANS directly

with hands. Always use oven mitts or pot holders to

protect hands from burns.

BEFORE USING THE COOKTOP



NOTE

Pan bottoms should not extend more than ½” (13mm)

beyond outer Cooking Zone (Induction).



NOTE

If a pan made of the correct material is centered

properly on any of the active Cooking Zones but is TOO

SMALL, the affected Cooking Zone display will ash the

power level and the pan will not heat.

The Cooking Zones available on the Induction Cooktop

require a MINIMUM pan size to be used at each location

(Figs. 2 & 3).

The outer tips of each cooking zone cross-hair is helpful

to determine the pan MAXIMUM size. After centering the

cookware on the cooktop, make sure the cookware does

not extend more than 1/2” beyond the thicker line on the

Cooking Zone. The pan must make FULL contact on the

glass surface without the bottom of the pan touching the

metal cooktop trims.

Cookware Recommendations Minimum Pan Size Requirements



NOTE

ANY one of the incorrect conditions listed above in Fig. 1

may be detected by the sensors located below the ceramic

cooktop surface. If the cookware does not meet any of

these conditions, one or more of the Cooking Zones will

not heat indicated by a ashing power level in the digital

display for that affected zone. Correct the problems before

attempting to reactivate the cooktop.

Be sure to follow the following recommendations for

using cookware as shown:

INCORRECT

CORRECT

• Cookware not centered

on Cooking Zone surface.

• Cookware centered

correctly on Cooking

Zone surface.

• Curved or warped pan

bottoms or sides.

• Flat pan bottom & straight

sides.

• Pan does not meet the

minimum size required for

the Cooking Zone used.

• Pan size meets or exceeds

the recommended minimum

size for the Cooking Zone.

• Pan bottom rests on cook-

top trim or does not rest

completely on the cook-

top surface.

• Pan rests completely on

the Cooktop surface.

• Heavy handle tilts pan.

• Pan is properly balanced.

Fig. 1

Fig. 2

Fig. 3

145mm

5 3/4”

Min.

145

5 3/4”

Min.

100

3 7/8”

Min.

230

9 1/16”

Min.

145mm

5 3/4”

Min.

180

7”

Min.

100

3 7/8”

Min.

230

9 1/16”

Min.

145

5 3/4”

Min.

SETTING INDUCTION SURFACE CONTROLS

Surface cooking settings

Use the chart to determine the correct setting for the

type of food you are preparing.

Note: The size and type of cookware used will inuence

the setting needed for best cooking results.

Recommended Setting for Surface Element

Setting Type of Cooking

HIGH (HI) Start most foods; bring water to a boil

and pan broiling.

MEDIUM HIGH

(8-10)

Continue a rapid boil; frying, deep fat

frying.

MEDIUM (6) Maintain a slow boil; thicken sauces

and gravies; steaming vegetables.

MEDIUM LOW

(2 - 4)

Keep foods cooking; poaching and

stewing.

LOW (LO) Keep warm, melting and simmering.

The Electronic Surface Element

Control

The Electronic Surface Element Control includes digital display

windows. The control provides a numeric digital setting for the

surface element positions on the cooktop. These settings work

the same way as normal knob setting indicators work except

the settings are displayed in digital windows (Figs. 1 thru 8).

The available Display Settings

The control provides various heat levels from Hi (Fig. 2) to Lo

(Fig. 4) and OFF (Fig. 1). The settings between 9.0 and 1.5

decrease or increase in increments of .5 (1/2).

Hot Element Indicator Message (HE)

After using any of the element positions the cooktop will

become very hot. Even after turning the control knob to OFF,

the cooktop will remain hot for some time. The control monitors

the temperature of the cooktop and displays the message "HE"

(hot element) warning when the cooktop is still too hot to touch

(See Fig. 5). If the HE message appears in the window, the

control can still be turned ON again for use.

Power Boost Indicator Message (Pb)

When an induction zone is rst set at Hi, the Power Boost

feature will turn on (see Fig. 6). The Power Boost feature

is used to bring large quantities of water or food to cooking

temperature at the fastest speed possible. The Power Boost

feature will give you up to 139% power output for a set

amount of time (approx. 10 min).

Error Indicator Message

An error message will be displayed at power up (or after a

power failure) if ANY of the surface control knobs were left

in the ON positions. If any control knobs were turned on

during a power failure of more than 10 seconds, the display

will show an “Er” message. If a power failure should occur,

be sure to set all of the surface control knobs to the OFF

position. This will reset the surface controls.

The induction zones are equipped with a pot detection system.

If the controls are activated and the detection system cannot

nd any pot of the correct material on the zone, it will ash

its power level for 3 minutes. After ashing for 3 minutes,

the digital display will show an “- -” message.

Error message “C” will only appear during a fault condition.

Error messages “Er” and “- -” may appear on display after

an invalid action by the user. Set surface control knob to

the OFF position to reset the control.

Once the surface controls have been set to the OFF positions,

the surface controls should return to normal operation. If

the surface controls do not function and the “C”, “Er”, or

“- -” message remains in any display after following these

procedures, contact your authorized servicer for assistance.

Fig. 5

Fig. 1

Fig. 3

Fig. 2

Fig. 4

Fig. 6

Control knobs shown are typical only.

SETTING INDUCTION SURFACE CONTROLS

Figure 1

Figure 2

CAUTION

The glass cooktop may appear to have cooled after

the elements have been turned OFF. The induction

elements do not heat directly the cooktop but heat will

be transferred from the cookware to the glass cooktop.

HE (Hot Element) message will turn ON and will continue

to glow until the glass cooktop has cooled down to a

moderate level. The glass surface may still be hot and

burns may occur if the glass surface is touched before the

indicator light has turned OFF. The message may remain

on even though the controls are turned OFF.

Figure 3

Operating the Single Induction

Surface Elements

The cooktop is equipped with 3 (or 4) single induction

surface elements: the RIGHT FRONT, CENTER and REAR

positions (Figure 1 and 2).

To Operate the Induction Surface

Elements

1. Place the correctly sized cookware of the proper

material on the induction surface element.

2. Push in and turn the surface control knob in either

direction to the desired setting (Figure 3).

Note: Turning the knob to Hi from Off will activate the

Power Boost feature. The Power Boost feature is used

to bring large quantities of water or food to cooking

temperature at the fastest speed possible. The Power

Boost feature will give you up to 139% power output

for a set amount of time (approx. 10 min). The

increased power output will vary per zone.

3. Turn the knob to adjust the setting if desired. Start

most cooking operations on a higher setting and then

turn to a lower setting to nish cooking. Each surface

element provides a constant amount of heat at each

setting.

4. When cooking has completed, turn the surface

control knob to OFF before removing the cookware.

Control knob

shown is

typical only.



NOTE

See Recommended Surface Cooking Settings table on

page 10.

CAUTION

Do not place plastic items such as salt and pepper

shakers, spoon holders or plastic wrappings on

cooktop when it is in use. These items could melt or

ignite. Potholders, towels or wooden spoons could catch

re if placed too close to the surface elements.

CAUTION

Do not allow aluminum foil, or ANY material that

can melt to make contact with the ceramic glass

cooktop. If these items melt on the cooktop they will

damage the ceramic cooktop.



NOTE

The surface "Element On" indicator light will glow

when one or more induction elements are turned on.

A quick glance at this indicator light when cooking

is nished is an easy check to be sure all surface

induction elements are turned off.

SETTING INDUCTION SURFACE CONTROLS

Figure 1

Figure 2

Figure 6

Front plus Rear

Figure 5

Front portion only

Bridge Induction Surface Radiant

Element

The cooktop features with a "BRIDGE" induction element

on the left side. (See Figures 1 & 2) positions. The bridge

can be used with rectangular or oval shaped cookware

such as a griddle. The bridge feature maintains an even

temperature setting across both elements. The “bridge”

mark on the knob indicates that both front and rear

portions will heat (Fig. 4). You may switch from bridge

to single elements settings at any time during cooking.

To switch settings, turn the front left control knob to OFF

rst. The cooktop will triple beep and ash the display if

the knob is not turned OFF before switching settings.



NOTE

The surface "Element On" indicator light will glow

when one or more induction elements are turned on.

A quick glance at this indicator light when cooking

is nished is an easy check to be sure all surface

induction elements are turned off.

See Recommended Surface Cooking Settings table on

page 10.

Figure 3

Front left control knob

Figure 4

Front left control knob

To Operate the Bridge Induction Element

as a single element:

If needed for normal cookware, the Bridge induction

element can work like a single induction element without

the Bridge (See Figure 5). The “single” mark on the knob

indicates that only the front portion will heat (Fig. 3).

1. Place the correctly sized cookware on the induction

bridge surface element.

2. Push in and turn the control knob as shown in

Figure 3 to heat the front portion of the Bridge

element for normal shaped cookware.

3. Turn the knob to adjust the setting if needed. Start

most cooking operations on a higher setting and

then turn to a lower setting to nish cooking. Each

induction element provides a constant amount

of heat at each setting. Please note that not all

cookware will t the Bridge element correctly.

4. When cooking has completed, turn the surface

control knob to OFF before removing the cookware.



NOTE

Both left front and rear elements must be OFF before

activating the bridge element. Bridge element will

only operate by using the front left control knob. The

left rear knob cannot be used while in bridge mode.

The cooktop will triple beep and the display will ash

until the left rear knob is turned OFF if the cooktop is

already in bridge mode.

Turning on the front left knob to activate the bridge

element while the left rear element is on will also cause

the cooktop to triple beep and the display will ash

until the left rear knob is turned OFF.

To Operate the Bridge Induction Element:

1. Place the correctly sized cookware on the induction

bridge surface element.

2. Push in and turn the control knob as shown in Figure

4 for larger or rectangular shaped cookware. The

“bridge” mark on the knob indicates that both front

and rear portions will heat.

3. Turn the knob to adjust the setting if needed. Start

most cooking operations on a higher setting and

then turn to a lower setting to nish cooking. Each

induction element provides a constant amount

of heat at each setting. Please note that not all

cookware will t the Bridge element correctly.

4. When cooking has completed, turn the surface

control knob to OFF before removing the cookware.

SETTING INDUCTION SURFACE CONTROLS

Figure 6

Front plus Rear

Figure 4

Front left control knob

Power Management

In order to give you more exibility, your induction

cooktop is equipped with more cooking zones than the

number of induction generators. Each of those generators

is assigned to power a specic cooking zone. One or two

cooking zones are assigned to each generator. If you use

more than one cooking zone at high power on the same

generator, the generator may need to manage its power

to both cooking zones.

Depending on the size of your cooktop, 2 or 3 generators

are available:

• The 30” cooktop is equipped with 4 cooking zones

within 2 sections.

• The 36” cooktop is equipped with ve cooking zones

within 3 sections.

To get the highest power output from your

cooking zones, start your cooking process on only one

cooking zone within the heating section and then add

your second cookware on the second cooking zone when

the rst one has already reached its cooking temperature.

Preheat Recommendations

When preheating a pan on the cooktop always watch

carefully. Whenever using the cooktop, always pay

attention to any items cooking and remain attentive until

the cooking process is complete.

Keep in mind that induction may decrease the amount of

time required to preheat a cooking utensil.

Operational Noises

The electronics generating the induction elds are pretty

much noiseless but they do produce heat at high power

level. A soft-sounding cooling fan activates when the

unit is running multiple cooking zones at once or when a

cooking zone is set at very high power settings.

The buzzing sound you could hear from your cooktop is

not coming from the electronics but from the cookware

you are using. Here are some causes of this noise:

• Most induction-ready cookware are made of several

layers of materials. An encapsulated steel layer

is usually used to harness the induction eld and

transform it into heat, which is then transferred to

the other materials by radiant energy. The induction

eld will cause the steel layer to vibrate against the

other materials in which it is encapsulated. This is

the most common cause of noise from the induction

process. This buzzing only happens at the higher

power level settings. Note that high quality cookware

manufacturers weld this steel layer in place which

lowers or cancel this noise.

• Light weight cookware may also vibrate. We

recommend using heavy weight quality cookware.

• Cookware with warped bottoms can vibrate on the

ceramic glass surface at high power settings.

• The power output of your induction

cooktop is capable of warping an empty pan. Never

use the higher power settings on an empty pan. Even

the highest quality cookware is vulnerable to warping.

• Riveted handles on cookware can also cause buzzing

sounds from the vibrations.

• Solid cast iron and enamelware cookware should not

emit any noise. Top quality cookware made of several

layers should also be relatively quiet.

SETTING INDUCTION SURFACE CONTROLS

Generators

CARE & CLEANING

Cleaning Various Parts of Your Cooktop

Before cleaning any part of the cooktop, be sure all controls are turned OFF and the cooktop is COOL. REMOVE SPILLOVERS

AND HEAVY SOILING AS SOON AS POSSIBLE. REGULAR CLEANINGS NOW WILL REDUCE THE DIFFICULTY AND EXTENT

OF A MAJOR CLEANING LATER.

Surfaces How to Clean

Stainless Steel

Decorative Trim Cooktop, Control

Knobs, Control Panel

Wipe the control panel clean after each use. Before cleaning the control

panel, turn all controls to OFF and remove the control knobs. To remove, pull each

knob straight off the shaft. Clean using hot, soapy water and a cloth. Do not use

cleaners with high concentrations of chlorides or chlorines. Do not use

harsh scrubbing cleaners. Be sure to squeeze excess water from the cloth before

wiping the panel; especially when wiping around the controls. Excess water in or

around the controls may cause damage to the appliance. Only use kitchen cleaners

that are especially made for cleaning stainless steel. Always be sure to rinse the

cleaners from the surface as bluish stains may occur during heating that cannot be

removed. To replace knobs after cleaning, line up the at sides of both the knob

and the shaft; then push the knob into place.

Ceramic Glass

Cooktop

See Ceramic Glass Cooktop in this Owner’s Guide.

Ceramic Glass Cooktop Cleaning &

Maintenance

Consistent and proper cleaning is

essential to maintaining your Ceramic

glass cooktop.

Prior to using your cooktop for the rst time, apply

a ceramic cooktop cleaning cream (available in most

hardware, grocery and department stores) to the ceramic

surface. Clean and buff with a clean paper towel. This will

make cleaning easier when soiled from cooking. Cooktop

cleaning creams leave a protective nish on the glass to

help prevent scratches and abrasions.

Sliding aluminum or copper clad bottom pans on the

cooktop can cause metal markings on the cooktop

surface. These marks should be removed immediately

after the cooktop has cooled using the cooktop cleaning

cream. Metal marks can become permanent if not

removed prior to future use.

Cookware (cast iron, metal, ceramic or glass) with rough

bottoms can mark or scratch the cooktop surface. Do

not slide anything metal or glass across the cooktop.

Do not use your cooktop as a cutting board or work

surface in the kitchen. Do not cook foods directly on the

cooktop surface without a pan. Do not drop heavy or

hard objects on the glass cooktop, or they may crack it.

CARE & CLEANING

Cleaning Recommendations for the

Ceramic Glass Cooktop

For light to moderate soil:

Apply a few drops of cleaning creme directly to the

cooktop. Use a paper towel or use a non-abrasive

plastic type no-scratch pad to clean the entire cooktop

surface. Make sure the cooktop is cleaned thoroughly,

leaving no residue.

For heavy, burned on soil:

Apply a few drops of cleaning Creme directly to the soiled

area. Rub the soiled area using a non-abrasive plastic

type no-scratch pad, applying pressure as needed. Do

not use the pad you use to clean the cooktop for any

other purpose.

Do not use the following on the ceramic glass

cooktop:

• Do not use abrasive cleaners and scouring pads,

such as metal and some nylon pads. They may

scratch the cooktop, making it more difcult to

clean.

• Do not use harsh cleaners, such as chlorine

bleach, ammonia or oven cleaners, as they may

etch or discolor the cooktop.

• Do not use dirty sponges, cloths or paper

towels, as they can leave soil or lint on the

cooktop which can burn and cause Special

Caution for Aluminum Foil and Aluminum

Cooking Utensils

WARNING

DO NOT use a cooktop cleaner on a hot cooktop.

The fumes can be hazardous to your health, and can

chemically damage the ceramic glass surface.

CAUTION

Before cleaning the cooktop, be sure the controls are

turned to OFF and the cooktop is COOL.

• Aluminum foil

Use of aluminum foil will damage the cooktop. Do not

use under any circumstances.

• Aluminum utensils

Since the melting point of aluminum is much lower

than that of other metals, care must be taken when

aluminum pots or pans are used. Pans that boil dry

may permanently damage cooktop by breaking, fusing

to, or marking it.

Care and Cleaning of Stainless Steel

Some models are equipped with stainless steel exterior

parts. Special care and cleaning are required for

maintaining the appearance of stainless parts. Refer

to the General Care & Cleaning table for detailed

cleaning instructions.

IMPORTANT

Damage to the ceramic glass cooktop may occur if you

use an abrasive type scratch pad. Only use cleaning

products that have been specically designed for

ceramic glass cooktop.

If soils remain, carefully scrape soils with a metal razor

blade scraper, holding scraper at a 30 degree angle to the

surface. Remove loosened soils, then apply a few drops

of cleaning cream and buff surface clean.

Plastic or foods with a high sugar content:

These types of soils need be removed immediately if

spilled or melted onto the ceramic cooktop surface.

Permanent damage (such as pitting of the cooktop

surface) may occur if not removed immediately. After

turning the surface elements OFF, use a razor blade

scraper or a metal spatula with a mitt and scrape the soil

from the hot surface (as illustrated). Allow the cooktop to

cool, and use the same method for heavy or burned on

soils.

IMPORTANT

Before you call for service, review this list. It may save you time and expense. The list includes common

occurrences that are not the result of defective workmanship or materials in this appliance.

BEFORE YOU CALL (Solutions to Common Problems)

OCCURRENCE POSSIBLE CAUSE/SOLUTION

Entire cooktop does

not operate.

House fuse has blown or circuit breaker has tripped. Check/reset breaker or replace fuse. If

the problem is a circuit overload, have this situation corrected by a qualied electrician.

Make sure household electrical circuit breaker is ON and that power is properly supplied to

the Cooktop.

Service wiring is not complete. Contact installation agent or dealer.

Electrical power outage. Check house lights to be sure. Call your local electric company for

service.

Cooktop turns OFF

while cooking.

Cooktop internal heat sensor has detected high temperatures inside the appliance. Be sure

the appliance vent holes are not blocked. Refer to the Installation Instructions supplied

with the cooktop for more detailed cooktop installation information.

Cooking Zone does

not heat food (Power

level is ashing).

No cookware was placed on the Cooking Zone, or the cookware material type is incorrect

for Induction Cooking.

Cookware bottom not large enough for Cooking Zone.

Cookware is warped or in poor condition.

Cookware is not centered on Cooking Zone.

Cookware resting on cooktop trim or does not rest completely on cooktop surface.

Cooking Zone does

not heat food.

No power to the appliance. Check steps under "Entire cooktop does not operate" in this

checklist.

Incorrect Cooking Zone control setting. Make sure the correct control is ON for the Cooking

Zone being used.

Cooking Zone heats

food too hot or not

hot enough.

Incorrect power level setting. Adjust the power level setting higher or lower and refer to

recipe for guidance and adjust accordingly.

Food does not heat

evenly.

Lightweight or warped pans were used. Be sure to use good quality cookware.

Use only at bottom, evenly balanced medium or heavyweight cookware. Heavy and

medium weight pans heat evenly. Because lightweight pans heat unevenly, foods may burn

more easily.

Adjust Cooking Zone power level setting until the proper amount of heat is obtained.

Poor cooking results. Many factors affect cooking results. Adjust the recipe’s recommended power levels or cooking

times.

Cookware is too lightweight or warped. Use heavier quality cookware so foods being

prepared may cook more evenly.

Cooktop Zone Control

displays C and

displays a 3 digits

error code.

Induction Cooktop main control has detected a fault or error condition. Try turning electrical

power supply OFF and back ON to cooktop in order to reset Cooktop main controls. If

fault recurs, record fault number and turn power supply to Cooktop OFF. Call service for

assistance.

BEFORE YOU CALL (Solutions to Common Problems)

OCCURRENCE POSSIBLE CAUSE/SOLUTION

Cooking Zone LED

continuously ashes.

Induction Cooktop pan detection sensors do not see the correct cookware. Test with a

magnet to be sure cookware is made with Induction compatible material.

Cookware has been removed from the Cooking Zone without turning the Cooking Zone OFF.

Place cookware back on to the Cooking Zone or if nished cooking turn off the affected

Cooking Zone.

Cookware is not centered over the Cooking Zone properly. Refer to page 7 for correct

cookware placement.

Metal marks on

ceramic cooktop

surface.

Sliding or scraping of metal utensils on cooktop surface. DO NOT slide cookware or cooking

utensils across the cooktop surface. Use the recommended ceramic glass cooktop cleaning

creme to remove the marks. See "Cooktop Cleaning & Maintenance" in the General Care &

Cleaning section.

Scratches or

abrasions on ceramic

cooktop surface.

Coarse particles such as salt or sand between cooktop and cookware or cooking utensils

can cause scratches. Be sure cooktop surface and bottoms of utensils are clean before

placing on cooktop. Small scratches do not affect cooking and will become less visible with

time.

Cleaning materials not recommended for ceramic-glass cooktop have been used. See

"Cooktop Cleaning & Maintenance" in the General Care & Cleaning section.

Cookware with rough bottoms was used. Use smooth, at-bottomed cookware ONLY.

Brown streaks or

specks on ceramic

cooktop surface.

Boil overs are cooked onto cooktop surface. Use a razor blade scraper to remove soil. See

"Cooktop Cleaning & Maintenance" in the General Care & Cleaning section.

Areas of discoloration

with metallic sheen

on ceramic cooktop

surface.

Mineral deposits from food and/or water. Remove using a ceramic-glass cooktop cleaning

creme. Remember to use cookware with clean, dry bottoms. For more information See

"Cooktop Cleaning and Maintenance" in the General Care & Cleaning section.

Cooktop makes

buzzing noise.

Cookware is damaged. Please see pages 6 & 7 of this manual. Also see “Operational noise”

section on page 11.

Fig. 1

Error Codes Display Message

If an error occurs in any of the zones, the C0 error message

will display in zones 1 or 2 on the left side of the cooktop.

If the error occurs while either of the rst two zones have

been on and the zone is hot enough to display HE, the error

message will override the hot element warning.

MAJOR APPLIANCE WARRANTY

This warranty does not cover the following:

1 Products with original serial numbers that have been removed, altered or cannot be readily

determined.

2 Product that has been transferred from its original owner to another party or removed outside the

USA or Canada.

3 Rust on the interior or exterior of the unit.

4 Products purchased "as-is" are not covered by this warranty.

5 Food loss due to any refrigerator or freezer failures.

6 Products used in a commercial setting.

7 Service calls which do not involve malfunction or defects in materials or workmanship, or for

appliances not in ordinary household use or used other than in accordance with the provided

instructions.

8 Service calls to correct the installation of your appliance or to instruct you how to use your appliance.

9 Expenses for making the appliance accessible for servicing, such as removal of trim, cupboards,

shelves, etc., which are not a part of the appliance when it is shipped from the factory.

10 Service calls to repair or replace appliance light bulbs, air lters, water lters, other consumable, or

knobs, handles, or other cosmetic parts.

11 Surcharges including, but not limited to, any after hour, weekend, or holiday service calls, tolls, ferry

trip charges, or mileage expense for service calls to remote areas, including the state of Alaska.

12 Damages to the nish of appliance or home incurred during installation, including but not limited to

oors, cabinets, walls, etc.

13 Damages caused by: services performed by unauthorized service companies; use of parts other than

genuine Electrolux parts or parts obtained from persons other than authorized service companies; or

external causes such as abuse, misuse, inadequate power supply, accidents, res, or acts of God.

DISCLAIMER OF IMPLIES WARRANTIES; LIMITATION OF REMEDIES

Customer’s sole and exclusive remedy under this limited warranty shall be product repair or

replacement as provided herein. Claims based on implied warranties, including warranties of

merchantability or fitness for particular purpose, are limited to one year or the shortest period

allowed by law, but not less than one year. Electrolux shall not be liable for consequential or

incidental damages such as property damage and incidental expenses resulting from any breach

of this written limited warranty or any implied warranty. Some states and provinces do not allow

the exclusion or limitation of incidental or consequential damages, or limitations on the duration of

implied warranties, so these limitations or exclusions may not imply to you. This written warranty

gives you specific legal rights. You may also have other rights that vary from state to state.

Keep your receipt, delivery slip, or some other appropriate payment record to establish the warranty period

should service be required. If service is performed, it is in your best interest to obtain and keep all receipts.

Service under this warranty must be obtained contacting Electrolux at the addresses or phone numbers

below.

Exclusions

If You

Need

Service

USA

1.800.944.9044

Electrolux Major Appliances

North America

P.O. Box 212378

Augusta, GA 30907

Canada

1.800.265.8352

Electrolux Canada Corp.

5855 Terry Fox Way

Mississauga, Ontario, Canada

L5V 3E4

Your appliance is covered by a one year limited warranty. For one year from your original date of purchase, Electrolux

will pay all costs for repairing or replacing any parts of this appliance that prove to be defective in materials or

workmanship when such appliance is installed, used and maintained in accordance with the provided instructions.

This warranty only applies in the USA and Canada. In the USA, your appliance is warranted by Electrolux Major

Appliances North America, a division of Electrolux Home Products, Inc. In Canada, your appliance is warranted by

Electrolux Canada Corp. Electrolux authorizes no person to change or add to any obligations under this warranty.

Obligations for service and parts under this warranty must be performed by Electrolux or an authorized service

company. Product features or specications as described or illustrated are subject to change without notice.

La page charge ...

Frigidaire FPIC3077RF Manuel utilisateur

Marque: Frigidaire

Modèle: FPIC3077RF

Catégorie: Cuisinières

Taper: Manuel utilisateur

Ce manuel convient également à

FPIC3677RF

Télécharger le PDF

rapport

dans d''autres langues

English: Frigidaire FPIC3077RF User manual

Frigidaire FPIC3077RF Manuel utilisateur

Ce manuel convient également à

Frigidaire FPIC3077RF Manuel utilisateur

dans d''autres langues

Autres documents